Properly initialize scatterlist before using it.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Defined SSDID & HW vendor brand strings. Added entries for SSDID within the
function that prints the brand string.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When resetting an ipr adapter, we use scsi_block_requests to
block any new commands from scsi core, and then unblock after
the reset. When hotplug removing an adapter, we shut it down
and go through this same code, but we've seen issues with
scsi_unblock_requests running after the adapter's memory has
been freed. There is really no need to block/unblock when
the adapter is being removed, so this patch skips the
block/unblock and will immediately fail any commands that
happen to make it to queuecommand while the adapter is
being shutdown.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fnic Trace utility is a tracing functionality built directly into fnic driver
to trace events. The benefit that trace buffer brings to fnic driver is the
ability to see what it happening inside the fnic driver. It also provides the
capability to trace every IO event inside fnic driver to debug panics, hangs
and potentially IO corruption issues. This feature makes it easy to find
problems in fnic driver and it also helps in tracking down strange bugs in a
more manageable way. Trace buffer is shared across all fnic instances for
this implementation.
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added new fnic debug flags for identifying IO state at every stage of IO while
debugging and also added more log messages for better debugging capability.
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The issue was observed when LUN Reset is issued through IOCTL or sg_reset
utility.
fnic driver issues LUN RESET to firmware. On successful completion of device
reset, driver cleans up all the pending IOs that were issued prior to device
reset. These pending IOs are expected to be in ABTS_PENDING state. This works
fine, when the device reset operation resulted from midlayer, but not when
device reset was triggered from IOCTL path as the pending IOs were not in
ABTS_PENDING state. execution path hits panic if the pending IO is not in
ABTS_PENDING state.
Changes:
The fix replaces BUG_ON check in fnic_clean_pending_aborts() with marking
pending IOs as ABTS_PENDING if they were not in ABTS_PENDING state and skips
if they were already in ABTS_PENDING state. An extra check is added to validate
the abort status of the commands after a delay of 2 * E_D_TOV using a
helper function. The helper function returns 1 if it finds any pending IO in
ABTS_PENDING state, belong to the LUN on which device reset was issued else 0.
With this, device reset operation returns success only if the helper funciton
returns 0, otherwise it returns failure.
Other changes:
- Removed code in fnic_clean_pending_aborts() that returns failure if it finds
io_req NULL, instead of returning failure added code to continue with next io
- Added device reset flags for debugging in fnic_terminate_rport_io,
fnic_rport_exch_reset, and fnic_clean_pending_aborts
Signed-off-by: Narsimhulu Musini <nmusini@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver allows IOs with more SGEs than max SGEs supported by Palo. The current
max SGEs supported by the fnic driver is 1024. The current register settings
on Palo supports a max of 256 only. Palo would return any IO with more than
256 SGEs with an error indicating INVALID_SGLS. Fnic driver should limit the
max supported SGLs in the driver to 256 to avoid this error.
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
1. Handling overlapped firmware resets
This fix serialize multiple firmware resets to avoid situation where fnic
device fails to come up for link up event, when firmware resets are issued
back to back. If there are overlapped firmware resets are issued,
the firmware reset operation checks whether there is any firmware reset in
progress, if so it polls for its completion in a loop with 100ms delay.
2. Handling device reset timeout
fnic_device_reset code has been modified to handle Device reset timeout:
- Issue terminate on device reset timeout.
- Introduced flags field (one of the scratch fields in scsi_cmnd).
With this, device reset request would have DEVICE_RESET flag set for other
routines to determine the type of the request.
Also modified fnic_terminate_rport_io, fnic_rport_exch_rset, completion
routines to handle SCSI commands with DEVICE_RESET flag.
3. LUN/Device Reset hangs when issued through IOCTL using utilities like
sg_reset.
Each SCSI command is associated with a valid tag, fnic uses this tag to
retrieve associated scsi command on completion. the LUN/Device Reset issued
through IOCTL resulting into a SCSI command that is not associated with a
valid tag. So fnic fails to retrieve associated scsi command on completion,
which causes hang. This fix allocates tag, associates it with the
scsi command and frees the tag, when the operation completed.
4. Preventing IOs during firmware reset.
Current fnic implementation allows IO submissions during firmware reset.
This fix synchronizes IO submissions and firmware reset operations.
It ensures that IOs issued to fnic prior to reset will be issued to the
firmware before firmware reset.
Signed-off-by: Narsimhulu Musini <nmusini@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
All memory regions are allocated based on variables total_len
and alignment but free was based on element_size.
Signed-off-by: Sakthivel K <DL.Team.PMC.SPC.Linux.open.source@pmcs.com>
Signed-off-by: Anand Kumar S <DL.Team.PMC.SPC.Linux.open.source@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch updates the megaraid_sas driver version and updates
Documentation/scsi/ChangeLog.megaraid_sas.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas will fix an issue where the
driver should not be loading the DevHandle unless FastPath is enabled.
If FastPath was not enabled, this means the hardware raid map
validation failed for some reason, or the map was corrupted, which
could mean the DevHandle could be invalid.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas will allow Fastpath T10PI/DIF
frame builds to work with 4k sector size.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Wait for the IDC complete AEN before returning the loopback operation back to
the application to make sure the port is put back into normal operations.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Give priority to I2C thermal.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently,the driver is processes RSCNs for each new NPIV ports that is created.
Processing the RSCN includes a name server query to see what has changed at the
name server side. The name server query is performed by the physical port and
each virtual port on the physical adapter (since the RSCN is passed to each
virtual port for processing). As the number of virtual ports being created
increases, this causes a lot of traffic and busies the firmware.
Processing the RSCN for a virtual port we already have a priori knowledge of is
not necessary so check the 24-bit fabric ID of the RSCN entry and skip
processing it if the RSCN is for a virtual port we already know about.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Code in qla24xx_report_id_acquisition() incorrectly assumed that
upon completion of list iteration (with no match), the 'pos'
(vp) variable passed to list_for_each_entry() would be set to
NULL. In this context, if the firmware were to return an
unrecognized vp_idx, the follow-on assignments to vp-members
could result in corruption of the structure.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Compiling qla_gs.o (part of the qla2xxx module) triggers two GCC
warnings:
drivers/scsi/qla2xxx/qla_gs.c: In function ‘qla2x00_fdmi_rhba’:
drivers/scsi/qla2xxx/qla_gs.c:1339:7: warning: array subscript is above array bounds [-Warray-bounds]
drivers/scsi/qla2xxx/qla_gs.c: In function ‘qla2x00_fdmi_register’:
drivers/scsi/qla2xxx/qla_gs.c:1663:15: warning: array subscript is above array bounds [-Warray-bounds]
It seems that the sequence of a strcpy followed by a strlen confuses GCC
when it is keeping track of array bounds here. (It is not clear to me
which array triggers this warning and by how much GCC thinks the
subscript is above its bounds. Neither is it clear to me why comparable
code in these two functions doesn't trigger this warning.)
An easy way to silence these warnings is to use preprocessor macros and
strncpy, as that apparently gives GCC enough information to keep track
of array bounds.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If we need to do a chip reset because of a serious loopback error don't try to
reset the loopback mode on the port as the mailbox command will timeout.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add the following error handling for loopback diagnostic mode with ISP83xx:
1. If we do not receive an MBA_DCBX_COMPLETE after our initial set port
configuration command, try to reset the port back into normal operation.
If that fails, take a FCoE dump and then reset the chip.
2. After completing the loopback diagnostic operation, if the reset of the port
back into normal operation fails then reset the port so we take a FCoE dump
and then reset the chip.
3. When we receive an IDC notification and the requested operation is loopback
extend the loop down timer so the link does not appear to down for an
extended period of time.
[jejb: fix checkpatch issue]
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
BSG code path increments ref count in the send path, but does not
decrement in the return path leading to hang during unload of the
driver.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
To avoid continually doing ISP resets when get loop id fails to
obtain the adapter loop id, first try to do a link initialization.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If another function on the port has initiated a loopback operation do not
process the current request.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the Read SFP mailbox command fails on the thermal device,
print a message explaining that thermal is not supported.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There's a subtle race in the loop/bus-reset handling whereby a
VHA's loop-state can get incorrectly set to 'down' after the
loop-reset and firmware's completion of link re-negotiation. The
original code incorrectly assumes that firmware AENs would arrive
only after mailbox-command execution to initiate the link-flap.
Here's a good case with the old code (AENs arrive after
mailbox-command completion):
qla2xxx [0000:03:00.1]-8012:91: BUS RESET ISSUED nexus=91:0:4.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010100.
qla2xxx [0000:03:00.1]-580e:91: Asynchronous P2P MODE received.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010400.
qla2xxx [0000:03:00.1]-802b:91: BUS RESET SUCCEEDED nexus=91:0:4.
qla2xxx [0000:03:00.1]-480b:91: Reset marker scheduled.
qla2xxx [0000:03:00.1]-5812:91: Port database changed ffff 0006 0000.
qla2xxx [0000:03:00.1]-505f:91: Link is operational (4 Gbps).
qla2xxx [0000:03:00.1]-480c:91: Reset marker end.
qla2xxx [0000:03:00.1]-480f:91: Loop resync scheduled.
qla2xxx [0000:03:00.1]-8837:91: F/W Ready - OK.
qla2xxx [0000:03:00.1]-883a:91: fw_state=3 (7, 0, 0, 0) curr time=170b8f315.
qla2xxx [0000:03:00.1]-280e:91: HBA in F P2P topology.
qla2xxx [0000:03:00.1]-2812:91: qla2x00_configure_hba success
qla2xxx [0000:03:00.1]-2814:91: Configure loop -- dpc flags = 0x5260.
notice how the 'Port database changed' (8014) arrived after the
bus-reset handler completed 'BUS RESET SUCCEEDED'.
Now, here's a failing case with the old code (AENs arrive before
mailbox-command completion):
qla2xxx [0000:03:00.1]-8012:91: BUS RESET ISSUED nexus=91:0:0.
qla2xxx [0000:03:00.1]-580e:91: Asynchronous P2P MODE received.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010100.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010400.
qla2xxx [0000:03:00.1]-4800:91: DPC handler sleeping.
qla2xxx [0000:03:00.1]-5812:91: Port database changed ffff 0006 0000.
qla2xxx [0000:03:00.1]-505f:91: Link is operational (4 Gbps).
qla2xxx [0000:03:00.1]-802b:91: BUS RESET SUCCEEDED nexus=91:0:0.
qla2xxx [0000:03:00.1]-480b:91: Reset marker scheduled.
qla2xxx [0000:03:00.1]-480c:91: Reset marker end.
qla2xxx [0000:03:00.1]-480f:91: Loop resync scheduled.
qla2xxx [0000:03:00.1]-8837:91: F/W Ready - OK.
qla2xxx [0000:03:00.1]-883a:91: fw_state=3 (7, 0, 0, 0) curr time=170be9eb2.
qla2xxx [0000:03:00.1]-280e:91: HBA in F P2P topology.
qla2xxx [0000:03:00.1]-2812:91: qla2x00_configure_hba success
qla2xxx [0000:03:00.1]-2814:91: Configure loop -- dpc flags = 0x5260.
qla2xxx [0000:03:00.1]-281e:91: Needs RSCN update and loop transition.
qla2xxx [0000:03:00.1]-286a:91: qla2x00_configure_loop *** FAILED ***.
qla2xxx [0000:03:00.1]-4810:91: Loop resync end.
qla2xxx [0000:03:00.1]-4800:91: DPC handler sleeping.
This race would ultimately lead to devices go unexpectedly
offline until another link-flap or chip-reset would cause driver
re-discovery to take place.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Base the number of outstanding requests the driver will keep track of on the
available resources instead of being hard-coded.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There wasn't any error handling for this kzalloc().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The error path calls dma_pool_free() on this path but "chap_table" is
NULL and "chap_dma" is uninitialized. It's cleaner to just return
directly.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Root cause is libsas will clear asd_sas_port phy_mask value in sas_port_deform
after triggering destruct workqueue, but the workqueue will send sync cmd and
still need phy_mask value. Now, mvsas using asd_sas_phy setting instead of
asd_sas_port setting.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Delete successive tests to the same location. The code tested the result
of a previous allocation, that itself was already tested. It is changed to
test the result of the most recent allocation.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
While reading sysfs chap_in_idx and chap_out_idx attribute, if chap
authentication is not set we get an error as "Invalid argument".
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Boot from SAN fails in some cases where boot target login response
is slow. In this case, probe finishes early and triggers init, which
doesn't find remote disk to mount root which leads to BFS failure.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch force driver to collect firmware dump using following command:-
"echo 2 > /sys/class/scsi_host/hostX/device/fw_dump"
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
