Pull ucounts fixes from Eric Biederman:
"There has been one very hard to track down bug in the ucount code that
we have been tracking since roughly v5.14 was released. Alex managed
to find a reliable reproducer a few days ago and then I was able to
instrument the code and figure out what the issue was.
It turns out the sigqueue_alloc single atomic operation optimization
did not play nicely with ucounts multiple level rlimits. It turned out
that either sigqueue_alloc or sigqueue_free could be operating on
multiple levels and trigger the conditions for the optimization on
more than one level at the same time.
To deal with that situation I have introduced inc_rlimit_get_ucounts
and dec_rlimit_put_ucounts that just focuses on the optimization and
the rlimit and ucount changes.
While looking into the big bug I found I couple of other little issues
so I am including those fixes here as well.
When I have time I would very much like to dig into process ownership
of the shared signal queue and see if we could pick a single owner for
the entire queue so that all of the rlimits can count to that owner.
That should entirely remove the need to call get_ucounts and
put_ucounts in sigqueue_alloc and sigqueue_free. It is difficult
because Linux unlike POSIX supports setuid that works on a single
thread"
* 'ucount-fixes-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ucounts: Move get_ucounts from cred_alloc_blank to key_change_session_keyring
ucounts: Proper error handling in set_cred_ucounts
ucounts: Pair inc_rlimit_ucounts with dec_rlimit_ucoutns in commit_creds
ucounts: Fix signal ucount refcounting
Current release - regressions:
- revert "vrf: reset skb conntrack connection on VRF rcv",
there are valid uses for previous behavior
- can: m_can: fix iomap_read_fifo() and iomap_write_fifo()
Current release - new code bugs:
- mlx5: e-switch, return correct error code on group creation failure
Previous releases - regressions:
- sctp: fix transport encap_port update in sctp_vtag_verify
- stmmac: fix E2E delay mechanism (in PTP timestamping)
Previous releases - always broken:
- netfilter: ip6t_rt: fix out-of-bounds read of ipv6_rt_hdr
- netfilter: xt_IDLETIMER: fix out-of-bound read caused by lack of init
- netfilter: ipvs: make global sysctl read-only in non-init netns
- tcp: md5: fix selection between vrf and non-vrf keys
- ipv6: count rx stats on the orig netdev when forwarding
- bridge: mcast: use multicast_membership_interval for IGMPv3
- can:
- j1939: fix UAF for rx_kref of j1939_priv
abort sessions on receiving bad messages
- isotp: fix TX buffer concurrent access in isotp_sendmsg()
fix return error on FC timeout on TX path
- ice: fix re-init of RDMA Tx queues and crash if RDMA was not inited
- hns3: schedule the polling again when allocation fails,
prevent stalls
- drivers: add missing of_node_put() when aborting
for_each_available_child_of_node()
- ptp: fix possible memory leak and UAF in ptp_clock_register()
- e1000e: fix packet loss in burst mode on Tiger Lake and later
- mlx5e: ipsec: fix more checksum offload issues
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Hwqr
-----END PGP SIGNATURE-----
Merge tag 'net-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, and can.
We'll have one more fix for a socket accounting regression, it's still
getting polished. Otherwise things look fine.
Current release - regressions:
- revert "vrf: reset skb conntrack connection on VRF rcv", there are
valid uses for previous behavior
- can: m_can: fix iomap_read_fifo() and iomap_write_fifo()
Current release - new code bugs:
- mlx5: e-switch, return correct error code on group creation failure
Previous releases - regressions:
- sctp: fix transport encap_port update in sctp_vtag_verify
- stmmac: fix E2E delay mechanism (in PTP timestamping)
Previous releases - always broken:
- netfilter: ip6t_rt: fix out-of-bounds read of ipv6_rt_hdr
- netfilter: xt_IDLETIMER: fix out-of-bound read caused by lack of
init
- netfilter: ipvs: make global sysctl read-only in non-init netns
- tcp: md5: fix selection between vrf and non-vrf keys
- ipv6: count rx stats on the orig netdev when forwarding
- bridge: mcast: use multicast_membership_interval for IGMPv3
- can:
- j1939: fix UAF for rx_kref of j1939_priv abort sessions on
receiving bad messages
- isotp: fix TX buffer concurrent access in isotp_sendmsg() fix
return error on FC timeout on TX path
- ice: fix re-init of RDMA Tx queues and crash if RDMA was not inited
- hns3: schedule the polling again when allocation fails, prevent
stalls
- drivers: add missing of_node_put() when aborting
for_each_available_child_of_node()
- ptp: fix possible memory leak and UAF in ptp_clock_register()
- e1000e: fix packet loss in burst mode on Tiger Lake and later
- mlx5e: ipsec: fix more checksum offload issues"
* tag 'net-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (75 commits)
usbnet: sanity check for maxpacket
net: enetc: make sure all traffic classes can send large frames
net: enetc: fix ethtool counter name for PM0_TERR
ptp: free 'vclock_index' in ptp_clock_release()
sfc: Don't use netif_info before net_device setup
sfc: Export fibre-specific supported link modes
net/mlx5e: IPsec: Fix work queue entry ethernet segment checksum flags
net/mlx5e: IPsec: Fix a misuse of the software parser's fields
net/mlx5e: Fix vlan data lost during suspend flow
net/mlx5: E-switch, Return correct error code on group creation failure
net/mlx5: Lag, change multipath and bonding to be mutually exclusive
ice: Add missing E810 device ids
igc: Update I226_K device ID
e1000e: Fix packet loss on Tiger Lake and later
e1000e: Separate TGP board type from SPT
ptp: Fix possible memory leak in ptp_clock_register()
net: stmmac: Fix E2E delay mechanism
nfc: st95hf: Make spi remove() callback return zero
net: hns3: disable sriov before unload hclge layer
net: hns3: fix vf reset workqueue cannot exit
...
Fix a bug exposed by a previous fix, where running guests with certain SMT topologies
could crash the host on Power8.
Fix atomic sleep warnings when re-onlining CPUs, when PREEMPT is enabled.
Thanks to: Nathan Lynch, Srikar Dronamraju, Valentin Schneider.
-----BEGIN PGP SIGNATURE-----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=572c
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix a bug exposed by a previous fix, where running guests with
certain SMT topologies could crash the host on Power8.
- Fix atomic sleep warnings when re-onlining CPUs, when PREEMPT is
enabled.
Thanks to Nathan Lynch, Srikar Dronamraju, and Valentin Schneider.
* tag 'powerpc-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/smp: do not decrement idle task preempt count in CPU offline
powerpc/idle: Don't corrupt back chain when going idle
The enetc driver does not implement .ndo_change_mtu, instead it
configures the MAC register field PTC{Traffic Class}MSDUR[MAXSDU]
statically to a large value during probe time.
The driver used to configure only the max SDU for traffic class 0, and
that was fine while the driver could only use traffic class 0. But with
the introduction of mqprio, sending a large frame into any other TC than
0 is broken.
This patch fixes that by replicating per traffic class the static
configuration done in enetc_configure_port_mac().
Fixes: cbe9e83594 ("enetc: Enable TC offloading with mqprio")
Reported-by: Richie Pearn <richard.pearn@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: <Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20211020173340.1089992-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are two counters named "MAC tx frames", one of them is actually
incorrect. The correct name for that counter should be "MAC tx error
frames", which is symmetric to the existing "MAC rx error frames".
Fixes: 16eb4c85c9 ("enetc: Add ethtool statistics")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: <Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20211020165206.1069889-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'vclock_index' is accessed from sysfs, it shouled be freed
in release function, so move it from ptp_clock_unregister()
to ptp_clock_release().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_info instead to avoid unnamed/uninitialized noise:
[197088.688729] sfc 0000:01:00.0: Solarflare NIC detected
[197088.690333] sfc 0000:01:00.0: Part Number : SFN5122F
[197088.729061] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no SR-IOV VFs probed
[197088.729071] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no PTP support
Inspired by fa44821a4d ("sfc: don't use netif_info et al before
net_device is registered") from Heiner Kallweit.
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 1/10GbaseT modes were set up for cards with SFP+ cages in
3497ed8c85 ("sfc: report supported link speeds on SFP connections").
10GbaseT was likely used since no 10G fibre mode existed.
The missing fibre modes for 1/10G were added to ethtool.h in 5711a98221
("net: ethtool: add support for 1000BaseX and missing 10G link modes")
shortly thereafter.
The user guide available at https://support-nic.xilinx.com/wp/drivers
lists support for the following cable and transceiver types in section 2.9:
- QSFP28 100G Direct Attach Cables
- QSFP28 100G SR Optical Transceivers (with SR4 modules listed)
- SFP28 25G Direct Attach Cables
- SFP28 25G SR Optical Transceivers
- QSFP+ 40G Direct Attach Cables
- QSFP+ 40G Active Optical Cables
- QSFP+ 40G SR4 Optical Transceivers
- QSFP+ to SFP+ Breakout Direct Attach Cables
- QSFP+ to SFP+ Breakout Active Optical Cables
- SFP+ 10G Direct Attach Cables
- SFP+ 10G SR Optical Transceivers
- SFP+ 10G LR Optical Transceivers
- SFP 1000BASE‐T Transceivers
- 1G Optical Transceivers
(From user guide issue 28. Issue 16 which also includes older cards like
SFN5xxx/SFN6xxx has matching lists for 1/10/40G transceiver types.)
Regarding SFP+ 10GBASE‐T transceivers the latest guide says:
"Solarflare adapters do not support 10GBASE‐T transceiver modules."
Tested using SFN5122F-R7 (with 2 SFP+ ports). Supported link modes do not change
depending on module used (tested with 1000BASE-T, 1000BASE-BX10, 10GBASE-LR).
Before:
$ ethtool ext
Settings for ext:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
10000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Link partner advertised link modes: Not reported
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: off
Port: FIBRE
PHYAD: 255
Transceiver: internal
Current message level: 0x000020f7 (8439)
drv probe link ifdown ifup rx_err tx_err hw
Link detected: yes
After:
$ ethtool ext
Settings for ext:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Link partner advertised link modes: Not reported
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: off
Port: FIBRE
PHYAD: 255
Transceiver: internal
Supports Wake-on: g
Wake-on: d
Current message level: 0x000020f7 (8439)
drv probe link ifdown ifup rx_err tx_err hw
Link detected: yes
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter fixes for net:
1) Crash due to missing initialization of timer data in
xt_IDLETIMER, from Juhee Kang.
2) NF_CONNTRACK_SECMARK should be bool in Kconfig, from Vegard Nossum.
3) Skip netdev events on netns removal, from Florian Westphal.
4) Add testcase to show port shadowing via UDP, also from Florian.
5) Remove pr_debug() code in ip6t_rt, this fixes a crash due to
unsafe access to non-linear skbuff, from Xin Long.
6) Make net/ipv4/vs/debug_level read-only from non-init netns,
from Antoine Tenart.
7) Remove bogus invocation to bash in selftests/netfilter/nft_flowtable.sh
also from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-10-20
This series contains updates to e1000e, igc, and ice drivers.
Sasha fixes an issue with dropped packets on Tiger Lake platforms for
e1000e and corrects a device ID for igc.
Tony adds missing E810 device IDs for ice.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
superblocks issue was particularly annoying because for unexperienced
users it essentially exacted a reboot to establish a new functional
mount in that scenario.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAmFwWuYTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHziwdHB/wJEvFkMQrlzbgVmijhmneU+TseAMxR
UBGnsyHdiimIDWqzb81cBuDfrocQzyhntghP2lBzcbzI+gZN1KlrYzKAbYk++cfi
E5Zbw3U8+moa5B2CnO19QEgmJY5DoXYXb6AbO3udIIj1Ls9lx0ByUyDoSn6fZyVH
iUQ9OH7zVTsTscoaBiEVcutmhQjIFjoYJqPpfCg6/15xcXX/L1DvxQFBWOxXqHQw
LYfCQIu8orrA2QdZpuTRpklrMg1Ih+RmqYTdQST6tTtTKJUrHPI0r3A8c2vUoBk1
ph4fBNsAMUqFn1fIGT88PJg81RC5RC3E6D5PqErzRFsPbAv9FHfGYvGQ
=FadF
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.15-rc7' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"Two important filesystem fixes, marked for stable.
The blocklisted superblocks issue was particularly annoying because
for unexperienced users it essentially exacted a reboot to establish a
new functional mount in that scenario"
* tag 'ceph-for-5.15-rc7' of git://github.com/ceph/ceph-client:
ceph: fix handling of "meta" errors
ceph: skip existing superblocks that are blocklisted or shut down when mounting
Current Work Queue Entry (WQE) checksum (csum) flags in the ethernet
segment (eseg) in case of IPsec crypto offload datapath are not aligned
with PRM/HW expectations.
Currently the driver always sets the l3_inner_csum flag in case of IPsec
because of the wrong usage of skb->encapsulation as indicator for inner
IPsec header since skb->encapsulation is always ON for IPsec packets
since IPsec itself is an encapsulation protocol. The above forced a
failing attempts of calculating csum of non-existing segments (like in
the IP|ESP|TCP packet case which does not have an l3_inner) which led
to lots of packet drops hence the low throughput.
Fix by using xo->inner_ipproto as indicator for inner IPsec header
instead of skb->encapsulation in addition to setting the csum flags
as following:
* Tunnel Mode:
* Pkt: MAC IP ESP IP L4
* CSUM: l3_cs | l3_inner_cs | l4_inner_cs
*
* Transport Mode:
* Pkt: MAC IP ESP L4
* CSUM: l3_cs [ | l4_cs (checksum partial case)]
*
* Tunnel(VXLAN TCP/UDP) over Transport Mode
* Pkt: MAC IP ESP UDP VXLAN IP L4
* CSUM: l3_cs | l3_inner_cs | l4_inner_cs
Fixes: f1267798c9 ("net/mlx5: Fix checksum issue of VXLAN and IPsec crypto offload")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
IPsec crypto offload current Software Parser (SWP) fields settings in
the ethernet segment (eseg) are not aligned with PRM/HW expectations.
Among others in case of IP|ESP|TCP packet, current driver sets the
offsets for inner_l3 and inner_l4 although there is no inner l3/l4
headers relative to ESP header in such packets.
SWP provides the offsets for HW ,so it can be used to find csum fields
to offload the checksum, however these are not necessarily used by HW
and are used as fallback in case HW fails to parse the packet, e.g
when performing IPSec Transport Aware (IP | ESP | TCP) there is no
need to add SW parse on inner packet. So in some cases packets csum
was calculated correctly , whereas in other cases it failed. The later
faced csum errors (caused by wrong packet length calculations) which
led to lots of packet drops hence the low throughput.
Fix by setting the SWP fields as expected in a IP|ESP|TCP packet.
the following describe the expected SWP offsets:
* Tunnel Mode:
* SWP: OutL3 InL3 InL4
* Pkt: MAC IP ESP IP L4
*
* Transport Mode:
* SWP: OutL3 OutL4
* Pkt: MAC IP ESP L4
*
* Tunnel(VXLAN TCP/UDP) over Transport Mode
* SWP: OutL3 InL3 InL4
* Pkt: MAC IP ESP UDP VXLAN IP L4
Fixes: f1267798c9 ("net/mlx5: Fix checksum issue of VXLAN and IPsec crypto offload")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
During suspend flow the driver calls mlx5e_destroy_vlan_table() which
does not only delete the vlans steering flow rules, but also frees the
data on currently active vlans, thus it is not restored during resume
flow.
This fix keeps the vlan data on suspend flow and frees it only on driver
remove flow.
Fixes: 6783f0a21a ("net/mlx5e: Dynamic alloc vlan table for netdev when needed")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Dan Carpenter report:
The patch f47e04eb96: "net/mlx5: E-switch, Allow setting share/max
tx rate limits of rate groups" from May 31, 2021, leads to the
following Smatch static checker warning:
drivers/net/ethernet/mellanox/mlx5/core/esw/qos.c:483 esw_qos_create_rate_group()
warn: passing zero to 'ERR_PTR'
If min rate normalization failed then error code may be overwritten to 0
if scheduling element destruction succeed. Ignore this value and always
return initial one.
Fixes: f47e04eb96 ("net/mlx5: E-switch, Allow setting share/max tx rate limits of rate groups")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Both multipath and bonding events are changing the HW LAG state
independently.
Handling one of the features events while the other is already
enabled can cause unwanted behavior, for example handling
bonding event while multipath enabled will disable the lag and
cause multipath to stop working.
Fix it by ignoring bonding event while in multipath and ignoring FIB
events while in bonding mode.
Fixes: 544fe7c2e6 ("net/mlx5e: Activate HW multipath and handle port affinity based on FIB events")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Again it became bigger than wished, unfortunately, as this contains
quite a few ASoC fixes that came up a bit late. It also includes
yet more HD- and USB-audio quirks: I decided to merge them now, as
those are for stable, and we'll need them sooner or later.
Although the volumes are a bit high, all changes are device-specific
(and reasonably small) fixes, so it should be safe for the late rc.
-----BEGIN PGP SIGNATURE-----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=zrEF
-----END PGP SIGNATURE-----
Merge tag 'sound-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Again it became bigger than wished, unfortunately, as this contains
quite a few ASoC fixes that came up a bit late. It also includes yet
more HD- and USB-audio quirks: I decided to merge them now, as those
are for stable, and we'll need them sooner or later.
Although the volumes are a bit high, all changes are device-specific
(and reasonably small) fixes, so it should be safe for the late rc"
* tag 'sound-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Fix microphone sound on Jieli webcam.
ALSA: hda/realtek: Fixes HP Spectre x360 15-eb1xxx speakers
ALSA: usb-audio: Provide quirk for Sennheiser GSP670 Headset
ALSA: hda/realtek: Add quirk for Clevo PC50HS
ALSA: usb-audio: add Schiit Hel device to quirk table
ASoC: wm8960: Fix clock configuration on slave mode
ASoC: cs42l42: Ensure 0dB full scale volume is used for headsets
ASoC: soc-core: fix null-ptr-deref in snd_soc_del_component_unlocked()
ASoC: codec: wcd938x: Add irq config support
ASoC: DAPM: Fix missing kctl change notifications
ASoC: Intel: bytcht_es8316: Utilize dev_err_probe() to avoid log saturation
ASoC: Intel: bytcht_es8316: Switch to use gpiod_get_optional()
ASoC: Intel: bytcht_es8316: Use temporary variable for struct device
ASoC: Intel: bytcht_es8316: Get platform data via dev_get_platdata()
ASoC: wcd938x: Fix jack detection issue
ASoC: nau8824: Fix headphone vs headset, button-press detection no longer working
ASoC: cs4341: Add SPI device ID table
ASoC: pcm179x: Add missing entries SPI to device ID table
ASoC: fsl_xcvr: Fix channel swap issue with ARC
ASoC: pcm512x: Mend accesses to the I2S_1 and I2S_2 registers
-----BEGIN PGP SIGNATURE-----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=tBGu
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20211019' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit fix from Paul Moore:
"One small audit patch to add a pointer NULL check"
* tag 'audit-pr-20211019' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: fix possible null-pointer dereference in audit_filter_rules
As part of support for E810 XXV devices, some device ids were
inadvertently left out. Add those missing ids.
Fixes: 195fb97766 ("ice: add additional E810 device id")
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
The device ID for I226_K was incorrectly assigned, update the device
ID to the correct one.
Fixes: bfa5e98c9d ("igc: Add new device ID")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Update the HW MAC initialization flow. Do not gate DMA clock from
the modPHY block. Keeping this clock will prevent dropped packets
sent in burst mode on the Kumeran interface.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213651
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213377
Fixes: fb776f5d57 ("e1000e: Add support for Tiger Lake")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Mark Pearson <markpearson@lenovo.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
- While cleaning up some of the tracing recursion protection logic,
I discovered a scenario that the current design would miss, and
would allow an infinite recursion. Removing an optimization trick
that opened the hole, fixes the issue and cleans up the code as well.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYW7CqRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qmVWAQDnboKAUVmB/3D/L1T9XdWEq4AzCS6W
51QpzWff0pBVkwEAuc1af2gqDZ6/N9sQjN9kGxikY6luVs3CSQ1yHkcanQw=
=1zGP
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Recursion fix for tracing.
While cleaning up some of the tracing recursion protection logic, I
discovered a scenario that the current design would miss, and would
allow an infinite recursion. Removing an optimization trick that
opened the hole fixes the issue and cleans up the code as well"
* tag 'trace-v5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Have all levels of checks prevent recursion
- Renamed CTL_STATUS to CTL_FSTATUS to fix a redefined warning
-----BEGIN PGP SIGNATURE-----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=D96y
-----END PGP SIGNATURE-----
Merge tag 'nios2_fixes_for_v5.15_part2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux
Pull nios2 fix from Dinh Nguyen:
- Renamed CTL_STATUS to CTL_FSTATUS to fix a redefined warning
* tag 'nios2_fixes_for_v5.15_part2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
NIOS2: irqflags: rename a redefined register name
* kvm_stat: do not show halt_wait_ns since it is not a cumulative statistic
x86:
* clean ups and fixes for bus lock vmexit and lazy allocation of rmaps
* two fixes for SEV-ES (one more coming as soon as I get reviews)
* fix for static_key underflow
ARM:
* Properly refcount pages used as a concatenated stage-2 PGD
* Fix missing unlock when detecting the use of MTE+VM_SHARED
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmFtuqYUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNGbAf9Ha4mlieY7lDQLk96GydPwlMofi1B
dteRaWizokT0Xk7HovPr8G1zwwE9DrqO1FuHiZrkckzf7cloaPDvncLag3D3Vakr
dWIqa7MaavSWBKDpcEIKOEo2SfIBU38xXQSEpegz2f2fhZK0Ud2xUNtGQMNrYatX
Lz6FXHRvHDmv4+9EjASoGBd0/C/NxMaumYa1VOxMt8JPyn+zho0z5rUDKDF4pg70
KAgxVZuksy15XFRTgaSaU0BqVn9uCHwZVqRFKBm+ocPXIFjhdMkgrxJ7NSYB1T+N
VFqcUBTFTjhg9e5eZnQ6GMf9FXpLzK912VhCRd0uU5PGeBwUDJTSnyu5OQ==
=GZqR
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Tools:
- kvm_stat: do not show halt_wait_ns since it is not a cumulative statistic
x86:
- clean ups and fixes for bus lock vmexit and lazy allocation of rmaps
- two fixes for SEV-ES (one more coming as soon as I get reviews)
- fix for static_key underflow
ARM:
- Properly refcount pages used as a concatenated stage-2 PGD
- Fix missing unlock when detecting the use of MTE+VM_SHARED"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: SEV-ES: reduce ghcb_sa_len to 32 bits
KVM: VMX: Remove redundant handling of bus lock vmexit
KVM: kvm_stat: do not show halt_wait_ns
KVM: x86: WARN if APIC HW/SW disable static keys are non-zero on unload
Revert "KVM: x86: Open code necessary bits of kvm_lapic_set_base() at vCPU RESET"
KVM: SEV-ES: Set guest_state_protected after VMSA update
KVM: X86: fix lazy allocation of rmaps
KVM: SEV-ES: fix length of string I/O
KVM: arm64: Release mmap_lock when using VM_SHARED with MTE
KVM: arm64: Report corrupted refcount at EL2
KVM: arm64: Fix host stage-2 PGD refcount
KVM: s390: Function documentation fixes
We have the same LAN controller on different PCHs. Separate TGP board
type from SPT which will allow for specific fixes to be applied for
TGP platforms.
Suggested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Mark Pearson <markpearson@lenovo.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Setting cred->ucounts in cred_alloc_blank does not make sense. The
uid and user_ns are deliberately not set in cred_alloc_blank but
instead the setting is delayed until key_change_session_keyring.
So move dealing with ucounts into key_change_session_keyring as well.
Unfortunately that movement of get_ucounts adds a new failure mode to
key_change_session_keyring. I do not see anything stopping the parent
process from calling setuid and changing the relevant part of it's
cred while keyctl_session_to_parent is running making it fundamentally
necessary to call get_ucounts in key_change_session_keyring. Which
means that the new failure mode cannot be avoided.
A failure of key_change_session_keyring results in a single threaded
parent keeping it's existing credentials. Which results in the parent
process not being able to access the session keyring and whichever
keys are in the new keyring.
Further get_ucounts is only expected to fail if the number of bits in
the refernece count for the structure is too few.
Since the code has no other way to report the failure of get_ucounts
and because such failures are not expected to be common add a WARN_ONCE
to report this problem to userspace.
Between the WARN_ONCE and the parent process not having access to
the keys in the new session keyring I expect any failure of get_ucounts
will be noticed and reported and we can find another way to handle this
condition. (Possibly by just making ucounts->count an atomic_long_t).
Cc: stable@vger.kernel.org
Fixes: 905ae01c4a ("Add a reference to ucounts for each cred")
Link: https://lkml.kernel.org/r/7k0ias0uf.fsf_-_@disp2133
Tested-by: Yu Zhao <yuzhao@google.com>
Reviewed-by: Alexey Gladkov <legion@kernel.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
I got memory leak as follows when doing fault injection test:
unreferenced object 0xffff88800906c618 (size 8):
comm "i2c-idt82p33931", pid 4421, jiffies 4294948083 (age 13.188s)
hex dump (first 8 bytes):
70 74 70 30 00 00 00 00 ptp0....
backtrace:
[<00000000312ed458>] __kmalloc_track_caller+0x19f/0x3a0
[<0000000079f6e2ff>] kvasprintf+0xb5/0x150
[<0000000026aae54f>] kvasprintf_const+0x60/0x190
[<00000000f323a5f7>] kobject_set_name_vargs+0x56/0x150
[<000000004e35abdd>] dev_set_name+0xc0/0x100
[<00000000f20cfe25>] ptp_clock_register+0x9f4/0xd30 [ptp]
[<000000008bb9f0de>] idt82p33_probe.cold+0x8b6/0x1561 [ptp_idt82p33]
When posix_clock_register() returns an error, the name allocated
in dev_set_name() will be leaked, the put_device() should be used
to give up the device reference, then the name will be freed in
kobject_cleanup() and other memory will be freed in ptp_clock_release().
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: a33121e548 ("ptp: fix the race between the release of ptp_clock and cdev")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When utilizing End to End delay mechanism, the following error messages show up:
|root@ehl1:~# ptp4l --tx_timestamp_timeout=50 -H -i eno2 -E -m
|ptp4l[950.573]: selected /dev/ptp3 as PTP clock
|ptp4l[950.586]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE
|ptp4l[950.586]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE
|ptp4l[952.879]: port 1: new foreign master 001395.fffe.4897b4-1
|ptp4l[956.879]: selected best master clock 001395.fffe.4897b4
|ptp4l[956.879]: port 1: assuming the grand master role
|ptp4l[956.879]: port 1: LISTENING to GRAND_MASTER on RS_GRAND_MASTER
|ptp4l[962.017]: port 1: received DELAY_REQ without timestamp
|ptp4l[962.273]: port 1: received DELAY_REQ without timestamp
|ptp4l[963.090]: port 1: received DELAY_REQ without timestamp
Commit f2fb6b6275 ("net: stmmac: enable timestamp snapshot for required PTP
packets in dwmac v5.10a") already addresses this problem for the dwmac
v5.10. However, same holds true for all dwmacs above version v4.10. Correct the
check accordingly. Afterwards everything works as expected.
Tested on Intel Atom(R) x6414RE Processor.
Fixes: 14f347334b ("net: stmmac: Correctly take timestamp for PTPv2")
Fixes: f2fb6b6275 ("net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a")
Suggested-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If something goes wrong in the remove callback, returning an error code
just results in an error message. The device still disappears.
So don't skip disabling the regulator in st95hf_remove() if resetting
the controller via spi fails. Also don't return an error code which just
results in two error messages.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guangbin Huang says:
====================
net: hns3: add some fixes for -net
This series adds some fixes for the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 driver includes hns3.ko, hnae3.ko and hclge.ko.
hns3.ko includes network stack and pci_driver, hclge.ko includes
HW device action, algo_ops and timer task, hnae3.ko includes some
register function.
When SRIOV is enable and hclge.ko is removed, HW device is unloaded
but VF still exists, PF will not reply VF mbx messages, and cause
errors.
This patch fix it by disable SRIOV before remove hclge.ko.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The task of VF reset is performed through the workqueue. It checks the
value of hdev->reset_pending to determine whether to exit the loop.
However, the value of hdev->reset_pending may also be assigned by
the interrupt function hclgevf_misc_irq_handle(), which may cause the
loop fail to exit and keep occupying the workqueue. This loop is not
necessary, so remove it and the workqueue will be rescheduled if the
reset needs to be retried or a new reset occurs.
Fixes: 1cc9bc6e58 ("net: hns3: split hclgevf_reset() into preparing and rebuilding part")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when there is a rx page allocation failure, it is
possible that polling may be stopped if there is no more packet
to be reveiced, which may cause queue stall problem under memory
pressure.
This patch makes sure polling is scheduled again when there is
any rx page allocation failure, and polling will try to allocate
receive buffers until it succeeds.
Now the allocation retry is added, it is unnecessary to do the rx
page allocation at the end of rx cleaning, so remove it. And reset
the unused_count to zero after calling hns3_nic_alloc_rx_buffers()
to avoid calling hns3_nic_alloc_rx_buffers() repeatedly under
memory pressure.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx unused desc is the desc that need attatching new buffer
before refilling to hw to receive new packet, the number of
desc need attatching new buffer is calculated using next_to_use
and next_to_clean. when next_to_use == next_to_clean, currently
hns3 driver assumes that all the desc has the buffer attatched,
but 'next_to_use == next_to_clean' also means all the desc need
attatching new buffer if hw has comsumed all the desc and the
driver has not attatched any buffer to the desc yet.
This patch adds 'refill' in desc_cb to indicate whether a new
buffer has been refilled to a desc.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the max tx size supported by the hw is calculated by
using the max BD num supported by the hw. According to the hw
user manual, the max tx size is fixed value for both non-TSO and
TSO skb.
This patch updates the max tx size according to the manual.
Fixes: 8ae10cfb5089("net: hns3: support tx-scatter-gather-fraglist feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ets dwrr bandwidth of tc is set to 0, the hardware will switch to SP
mode. In this case, this tc may occupy all the tx bandwidth if it has
huge traffic, so it violates the purpose of the user setting.
To fix this problem, limit the ets dwrr bandwidth must greater than 0.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, DWRR of tc will be initialized to a fixed value when this tc
is enabled, but it is not been reset to 0 when this tc is disabled. It
cause a problem that the DWRR of unused tc is not 0 after using tc tool
to add and delete multi-tc parameters.
For examples, after enabling 4 TCs and restoring to 1 TC by follow
tc commands:
$ tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3 0 1 2 3 queues \
8@0 8@8 8@16 8@24 hw 1 mode channel
$ tc qdisc del dev eth0 root
Now there is just one TC is enabled for eth0, but the tc info querying by
debugfs is shown as follow:
$ cat /mnt/hns3/0000:7d:00.0/tm/tc_sch_info
enabled tc number: 1
weight_offset: 14
TC MODE WEIGHT
0 dwrr 100
1 dwrr 100
2 dwrr 100
3 dwrr 100
4 dwrr 0
5 dwrr 0
6 dwrr 0
7 dwrr 0
This patch fixes it by resetting DWRR of tc to 0 when tc is disabled.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add configuration of interrupt type and fifo interrupt enable of TM QCN
error event if enabled, otherwise this event will not be reported when
there is error.
Fixes: d914971df0 ("net: hns3: remove redundant query in hclge_config_tm_hw_err_int()")
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With PREEMPT_COUNT=y, when a CPU is offlined and then onlined again, we
get:
BUG: scheduling while atomic: swapper/1/0/0x00000000
no locks held by swapper/1/0.
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.15.0-rc2+ #100
Call Trace:
dump_stack_lvl+0xac/0x108
__schedule_bug+0xac/0xe0
__schedule+0xcf8/0x10d0
schedule_idle+0x3c/0x70
do_idle+0x2d8/0x4a0
cpu_startup_entry+0x38/0x40
start_secondary+0x2ec/0x3a0
start_secondary_prolog+0x10/0x14
This is because powerpc's arch_cpu_idle_dead() decrements the idle task's
preempt count, for reasons explained in commit a7c2bb8279 ("powerpc:
Re-enable preemption before cpu_die()"), specifically "start_secondary()
expects a preempt_count() of 0."
However, since commit 2c669ef697 ("powerpc/preempt: Don't touch the idle
task's preempt_count during hotplug") and commit f1a0a376ca ("sched/core:
Initialize the idle task with preemption disabled"), that justification no
longer holds.
The idle task isn't supposed to re-enable preemption, so remove the
vestigial preempt_enable() from the CPU offline path.
Tested with pseries and powernv in qemu, and pseries on PowerVM.
Fixes: 2c669ef697 ("powerpc/preempt: Don't touch the idle task's preempt_count during hotplug")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211015173902.2278118-1-nathanl@linux.ibm.com
In isa206_idle_insn_mayloss() we store various registers into the stack
red zone, which is allowed.
However inside the IDLE_STATE_ENTER_SEQ_NORET macro we save r2 again,
to 0(r1), which corrupts the stack back chain.
We used to do the same in isa206_idle_insn_mayloss() itself, but we
fixed that in 73287caa92 ("powerpc64/idle: Fix SP offsets when saving
GPRs"), however we missed that the macro also corrupts the back chain.
Corrupting the back chain is bad for debuggability but doesn't
necessarily cause a bug.
However we recently changed the stack handling in some KVM code, and it
now relies on the stack back chain being valid when it returns. The
corruption causes that code to return with r1 pointing somewhere in
kernel data, at some point LR is restored from the stack and we branch
to NULL or somewhere else invalid.
Only affects Power8 hosts running KVM guests, with dynamic_mt_modes
enabled (which it is by default).
The fixes tag below points to the commit that changed the KVM stack
handling, exposing this bug. The actual corruption of the back chain has
always existed since 948cf67c47 ("powerpc: Add NAP mode support on
Power7 in HV mode").
Fixes: 9b4416c509 ("KVM: PPC: Book3S HV: Fix stack handling in idle_kvm_start_guest()")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211020094826.3222052-1-mpe@ellerman.id.au
This reverts commit 09e856d54b.
When an interface is enslaved in a VRF, prerouting conntrack hook is
called twice: once in the context of the original input interface, and
once in the context of the VRF interface. If no special precausions are
taken, this leads to creation of two conntrack entries instead of one,
and breaks SNAT.
Commit above was intended to avoid creation of extra conntrack entries
when input interface is enslaved in a VRF. It did so by resetting
conntrack related data associated with the skb when it enters VRF context.
However it breaks netfilter operation. Imagine a use case when conntrack
zone must be assigned based on the original input interface, rather than
VRF interface (that would make original interfaces indistinguishable). One
could create netfilter rules similar to these:
chain rawprerouting {
type filter hook prerouting priority raw;
iif realiface1 ct zone set 1 return
iif realiface2 ct zone set 2 return
}
This works before the mentioned commit, but not after: zone assignment
is "forgotten", and any subsequent NAT or filtering that is dependent
on the conntrack zone does not work.
Here is a reproducer script that demonstrates the difference in behaviour.
==========
#!/bin/sh
# This script demonstrates unexpected change of nftables behaviour
# caused by commit 09e856d54b ""vrf: Reset skb conntrack
# connection on VRF rcv"
# https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=09e856d54bda5f288ef8437a90ab2b9b3eab83d1
#
# Before the commit, it was possible to assign conntrack zone to a
# packet (or mark it for `notracking`) in the prerouting chanin, raw
# priority, based on the `iif` (interface from which the packet
# arrived).
# After the change, # if the interface is enslaved in a VRF, such
# assignment is lost. Instead, assignment based on the `iif` matching
# the VRF master interface is honored. Thus it is impossible to
# distinguish packets based on the original interface.
#
# This script demonstrates this change of behaviour: conntrack zone 1
# or 2 is assigned depending on the match with the original interface
# or the vrf master interface. It can be observed that conntrack entry
# appears in different zone in the kernel versions before and after
# the commit.
IPIN=172.30.30.1
IPOUT=172.30.30.2
PFXL=30
ip li sh vein >/dev/null 2>&1 && ip li del vein
ip li sh tvrf >/dev/null 2>&1 && ip li del tvrf
nft list table testct >/dev/null 2>&1 && nft delete table testct
ip li add vein type veth peer veout
ip li add tvrf type vrf table 9876
ip li set veout master tvrf
ip li set vein up
ip li set veout up
ip li set tvrf up
/sbin/sysctl -w net.ipv4.conf.veout.accept_local=1
/sbin/sysctl -w net.ipv4.conf.veout.rp_filter=0
ip addr add $IPIN/$PFXL dev vein
ip addr add $IPOUT/$PFXL dev veout
nft -f - <<__END__
table testct {
chain rawpre {
type filter hook prerouting priority raw;
iif { veout, tvrf } meta nftrace set 1
iif veout ct zone set 1 return
iif tvrf ct zone set 2 return
notrack
}
chain rawout {
type filter hook output priority raw;
notrack
}
}
__END__
uname -rv
conntrack -F
ping -W 1 -c 1 -I vein $IPOUT
conntrack -L
Signed-off-by: Eugene Crosser <crosser@average.org>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of leaking the ucounts in new if alloc_ucounts fails, store
the result of alloc_ucounts into a temporary variable, which is later
assigned to new->ucounts.
Cc: stable@vger.kernel.org
Fixes: 905ae01c4a ("Add a reference to ucounts for each cred")
Link: https://lkml.kernel.org/r/87pms2s0v8.fsf_-_@disp2133
Tested-by: Yu Zhao <yuzhao@google.com>
Reviewed-by: Alexey Gladkov <legion@kernel.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The purpose of inc_rlimit_ucounts and dec_rlimit_ucounts in commit_creds
is to change which rlimit counter is used to track a process when the
credentials changes.
Use the same test for both to guarantee the tracking is correct.
Cc: stable@vger.kernel.org
Fixes: 21d1c5e386 ("Reimplement RLIMIT_NPROC on top of ucounts")
Link: https://lkml.kernel.org/r/87v91us0w4.fsf_-_@disp2133
Tested-by: Yu Zhao <yuzhao@google.com>
Reviewed-by: Alexey Gladkov <legion@kernel.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Merge misc fixes from Andrew Morton:
"19 patches.
Subsystems affected by this patch series: mm (userfaultfd, migration,
memblock, mempolicy, slub, secretmem, and thp), ocfs2, binfmt, vfs,
and misc"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mailmap: add Andrej Shadura
mm/thp: decrease nr_thps in file's mapping on THP split
mm/secretmem: fix NULL page->mapping dereference in page_is_secretmem()
vfs: check fd has read access in kernel_read_file_from_fd()
elfcore: correct reference to CONFIG_UML
mm, slub: fix incorrect memcg slab count for bulk free
mm, slub: fix potential use-after-free in slab_debugfs_fops
mm, slub: fix potential memoryleak in kmem_cache_open()
mm, slub: fix mismatch between reconstructed freelist depth and cnt
mm, slub: fix two bugs in slab_debug_trace_open()
mm/mempolicy: do not allow illegal MPOL_F_NUMA_BALANCING | MPOL_LOCAL in mbind()
memblock: check memory total_size
ocfs2: mount fails with buffer overflow in strlen
ocfs2: fix data corruption after conversion from inline format
mm/migrate: fix CPUHP state to update node demotion order
mm/migrate: add CPU hotplug to demotion #ifdef
mm/migrate: optimize hotplug-time demotion order updates
userfaultfd: fix a race between writeprotect and exit_mmap()
mm/userfaultfd: selftests: fix memory corruption with thp enabled
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAmFub7gTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqf6yCACAiYQuk1sRh7/b6G4Qk2QUTWUxhG/T
NWAOVuYMJkvGAMRAxjA7ecwRqA19/WIS2ys00t8UW62mvFGrGfcSBXWj3baPnx7w
rfhyd+gk1LqOjWcaQriDmLO2ERY27roNA7FMtcMCoRlbYkrnYcFyKUMdhQXSW3/R
/5KIEWBFzmr6ISUBUpkOeDs3irjy3ScIE0fEBt1+Uu3XydFWt7qnrMqBGlwoc9Xs
du5VN5nWTZzdB9ju7p0PyrYdwoHsa1L1XbnIJd1hTLCua38028nuL9v7OGy3QvwN
1Tz10PTnTk+2KMCkR4AwuzEBcHBVIcNmTrpTQAKiecB0QbXQlR9es0J5
=9TSz
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.15-20211019' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2021-10-19
this is a pull request of a single patch for net/master.
The patch is by me and fixes the error handling in case of a FC
timeout in the TX path of the ISOTOP CAN protocol.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
