We're moving pistachio to generic MIPS kernel. The clk driver
should be avilable to the generic MIPS kernel.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
- Texas Instruments' LMK04832 Ultra Low-Noise JESD204B Compliant Clock
Jitter Cleaner With Dual Loop PLLs
- Support secure mode of STM32MP1 SoCs
- Improve clock support for Actions S500 SoC
* clk-lmk04832:
clk: lmk04832: Use of match table
clk: lmk04832: Depend on SPI
clk: lmk04832: add support for digital delay
clk: add support for the lmk04832
dt-bindings: clock: add ti,lmk04832 bindings
* clk-stm:
clk: stm32mp1: new compatible for secure RCC support
dt-bindings: clock: stm32mp1 new compatible for secure rcc
dt-bindings: reset: add MCU HOLD BOOT ID for SCMI reset domains on stm32mp15
dt-bindings: reset: add IDs for SCMI reset domains on stm32mp15
dt-bindings: clock: add IDs for SCMI clocks on stm32mp15
reset: stm32mp1: remove stm32mp1 reset
clk: stm32mp1: move RCC reset controller into RCC clock driver
clk: stm32mp1: convert to module driver
clk: stm32mp1: remove intermediate pll clocks
clk: stm32mp1: merge 'ck_hse_rtc' and 'ck_rtc' into one clock
clk: stm32mp1: merge 'clk-hsi-div' and 'ck_hsi' into one clock
* clk-rohm:
clk: bd718xx: Drop BD70528 support
* clk-actions:
clk: actions: Add NIC and ETHERNET clock support for Actions S500 SoC
dt-bindings: clock: Add NIC and ETHERNET bindings for Actions S500 SoC
clk: actions: Fix AHPPREDIV-H-AHB clock chain on Owl S500 SoC
clk: actions: Fix bisp_factor_table based clocks on Owl S500 SoC
clk: actions: Fix SD clocks factor table on Owl S500 SoC
clk: actions: Fix UART clock dividers on Owl S500 SoC
* clk-ingenic:
clk: ingenic: Add support for the JZ4760
clk: ingenic: Support overriding PLLs M/N/OD calc algorithm
clk: ingenic: Remove pll_info.no_bypass_bit
clk: ingenic: Read bypass register only when there is one
clk: Support bypassing dividers
dt-bindings: clock: ingenic: Add ingenic,jz4760{,b}-cgu compatibles
The LMK04832 is an ultra-high performance clock conditioner with JEDEC
JESD204B support and is also pin compatible with the LMK0482x family of
devices.
Signed-off-by: Liam Beguin <lvb@xiphos.com>
Link: https://lore.kernel.org/r/20210423004057.283926-2-liambeguin@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This option is now synonymous with CONFIG_HAVE_CLK, so use
the latter globally. Any out-of-tree platform ports that
still use a private clk_get()/clk_put() implementation should
move to CONFIG_COMMON_CLK.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
usual suspects are here: i.MX, Qualcomm, Renesas, Allwinner, Samsung, and
Rockchip, but it feels pretty light on commits. There's only one real commit to
the framework core and that's to consolidate code. Otherwise the diffstat is
dominated by many Qualcomm clk driver patches that modernize the driver for the
proper way of speciying clk parents. That's shifting data around, which could
subtly break things so I'll be on the lookout for fixes.
New Drivers:
- Proper clk driver for Mediatek MT7621 SoCs
- Support for the clock controller on the new Rockchip rk3568
Updates:
- Simplify Zynq Kconfig dependencies
- Use clk_hw pointers in socfpga driver
- Cleanup parent data in qcom clk drivers
- Some cleanups for rk3399 modularization
- Fix reparenting of i.MX UART clocks by initializing only the ones
associated to stdout
- Correct the PCIE clocks for i.MX8MP and i.MX8MQ
- Make i.MX LPCG and SCU clocks return on registering failure
- Kernel doc fixes
- Add DAB hardware accelerator clocks on Renesas R-Car E3 and M3-N
- Add timer (TMU) clocks on Renesas R-Car H3 ES1.0
- Add Timer (TMU & CMT) and thermal sensor (TSC) clocks on Renesas R-Car V3U
- Sigma-delta modulation on Allwinner V3s audio PLL
-----BEGIN PGP SIGNATURE-----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=z+1G
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Here's a collection of largely clk driver updates. The usual suspects
are here: i.MX, Qualcomm, Renesas, Allwinner, Samsung, and Rockchip,
but it feels pretty light on commits.
There's only one real commit to the framework core and that's to
consolidate code. Otherwise the diffstat is dominated by many Qualcomm
clk driver patches that modernize the driver for the proper way of
speciying clk parents. That's shifting data around, which could subtly
break things so I'll be on the lookout for fixes.
New Drivers:
- Proper clk driver for Mediatek MT7621 SoCs
- Support for the clock controller on the new Rockchip rk3568
Updates:
- Simplify Zynq Kconfig dependencies
- Use clk_hw pointers in socfpga driver
- Cleanup parent data in qcom clk drivers
- Some cleanups for rk3399 modularization
- Fix reparenting of i.MX UART clocks by initializing only the ones
associated to stdout
- Correct the PCIE clocks for i.MX8MP and i.MX8MQ
- Make i.MX LPCG and SCU clocks return on registering failure
- Kernel doc fixes
- Add DAB hardware accelerator clocks on Renesas R-Car E3 and M3-N
- Add timer (TMU) clocks on Renesas R-Car H3 ES1.0
- Add Timer (TMU & CMT) and thermal sensor (TSC) clocks on
Renesas R-Car V3U
- Sigma-delta modulation on Allwinner V3s audio PLL"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (82 commits)
MAINTAINERS: add MT7621 CLOCK maintainer
staging: mt7621-dts: use valid vendor 'mediatek' instead of invalid 'mtk'
staging: mt7621-dts: make use of new 'mt7621-clk'
clk: ralink: add clock driver for mt7621 SoC
clk: uniphier: Fix potential infinite loop
clk: qcom: rpmh: add support for SDX55 rpmh IPA clock
clk: qcom: gcc-sdm845: get rid of the test clock
clk: qcom: convert SDM845 Global Clock Controller to parent_data
dt-bindings: clock: separate SDM845 GCC clock bindings
clk: qcom: apss-ipq-pll: Add missing MODULE_DEVICE_TABLE
clk: qcom: a53-pll: Add missing MODULE_DEVICE_TABLE
clk: qcom: a7-pll: Add missing MODULE_DEVICE_TABLE
dt: bindings: add mt7621-sysc device tree binding documentation
dt-bindings: clock: add dt binding header for mt7621 clocks
clk: samsung: Remove redundant dev_err calls
clk: zynqmp: pll: add set_pll_mode to check condition in zynqmp_pll_enable
clk: zynqmp: move zynqmp_pll_set_mode out of round_rate callback
clk: zynqmp: Drop dependency on ARCH_ZYNQMP
clk: zynqmp: Enable the driver if ZYNQMP_FIRMWARE is selected
clk: qcom: gcc-sm8350: use ARRAY_SIZE instead of specifying num_parents
...
The documentation for this SOC only talks about two
registers regarding to the clocks:
* SYSC_REG_CPLL_CLKCFG0 - provides some information about
boostrapped refclock. PLL and dividers used for CPU and some
sort of BUS.
* SYSC_REG_CPLL_CLKCFG1 - a banch of gates to enable/disable
clocks for all or some ip cores.
Looking into driver code, and some openWRT patched there are
another frequencies which are used in some drivers (uart, sd...).
According to all of this information the clock plan for this
SoC is set as follows:
- Main top clock "xtal" from where all the rest of the world is
derived.
- CPU clock "cpu" derived from "xtal" frequencies and a bunch of
register reads and predividers.
- BUS clock "bus" derived from "cpu" and with (cpu / 4) MHz.
- Fixed clocks from "xtal":
* "50m": 50 MHz.
* "125m": 125 MHz.
* "150m": 150 MHz.
* "250m": 250 MHz.
* "270m": 270 MHz.
We also have a buch of gate clocks with their parents:
* "hsdma": "150m"
* "fe": "250m"
* "sp_divtx": "270m"
* "timer": "50m"
* "pcm": "270m"
* "pio": "50m"
* "gdma": "bus"
* "nand": "125m"
* "i2c": "50m"
* "i2s": "270m"
* "spi": "bus"
* "uart1": "50m"
* "uart2": "50m"
* "uart3": "50m"
* "eth": "50m"
* "pcie0": "125m"
* "pcie1": "125m"
* "pcie2": "125m"
* "crypto": "250m"
* "shxc": "50m"
With this information the clk driver will provide clock and gates
functionality from a a set of hardcoded clocks allowing to define
a nice device tree without fixed clocks.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210410055059.13518-2-sergio.paracuellos@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Stratix 10 / Agilex / N5X clocks do not use anything other than OF
or COMMON_CLK so they should be compile testable on most of the
platforms.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Agilex, N5X and Stratix 10 share all quite similar arm64 hard cores and
SoC-part. Up to a point that N5X uses the same DTSI as Agilex. From
the Linux kernel point of view these are flavors of the same
architecture so there is no need for three top-level arm64
architectures. Simplify this by merging all three architectures into
ARCH_INTEL_SOCFPGA and dropping the other ARCH* arm64 Kconfig entries.
The side effect is that the INTEL_STRATIX10_SERVICE will now be
available for both 32-bit and 64-bit Intel SoCFPGA, even though it is
used only for 64-bit.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Simplify 32-bit and 64-bit Intel SoCFPGA Kconfig options by having only
one for both of them. This the common practice for other platforms.
Additionally, the ARCH_SOCFPGA is too generic as SoCFPGA designs come
from multiple vendors.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The Intel's eASIC N5X (ARCH_N5X) architecture shares a lot with Agilex
(ARCH_AGILEX) so it uses the same socfpga_agilex.dtsi, with minor
changes. Also the clock drivers are the same.
However the clock drivers won't be build without ARCH_AGILEX. One could
assume that ARCH_N5X simply depends on ARCH_AGILEX but this was not
modeled in Kconfig. In current stage the ARCH_N5X is simply
unbootable.
Add a separate Kconfig entry for clocks used by both ARCH_N5X and
ARCH_AGILEX so the necessary objects will be built if either of them is
selected.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
I have a handful of new RISC-V related patches for this merge window:
* A check to ensure drivers are properly using uaccess. This isn't
manifesting with any of the drivers I'm currently using, but may catch
errors in new drivers.
* Some preliminary support for the FU740, along with the HiFive
Unleashed it will appear on.
* NUMA support for RISC-V, which involves making the arm64 code generic.
* Support for kasan on the vmalloc region.
* A handful of new drivers for the Kendryte K210, along with the DT
plumbing required to boot on a handful of K210-based boards.
* Support for allocating ASIDs.
* Preliminary support for kernels larger than 128MiB.
* Various other improvements to our KASAN support, including the
utilization of huge pages when allocating the KASAN regions.
We may have already found a bug with the KASAN_VMALLOC code, but it's
passing my tests. There's a fix in the works, but that will probably
miss the merge window.
-----BEGIN PGP SIGNATURE-----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=CutX
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.12-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
"A handful of new RISC-V related patches for this merge window:
- A check to ensure drivers are properly using uaccess. This isn't
manifesting with any of the drivers I'm currently using, but may
catch errors in new drivers.
- Some preliminary support for the FU740, along with the HiFive
Unleashed it will appear on.
- NUMA support for RISC-V, which involves making the arm64 code
generic.
- Support for kasan on the vmalloc region.
- A handful of new drivers for the Kendryte K210, along with the DT
plumbing required to boot on a handful of K210-based boards.
- Support for allocating ASIDs.
- Preliminary support for kernels larger than 128MiB.
- Various other improvements to our KASAN support, including the
utilization of huge pages when allocating the KASAN regions.
We may have already found a bug with the KASAN_VMALLOC code, but it's
passing my tests. There's a fix in the works, but that will probably
miss the merge window.
* tag 'riscv-for-linus-5.12-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (75 commits)
riscv: Improve kasan population by using hugepages when possible
riscv: Improve kasan population function
riscv: Use KASAN_SHADOW_INIT define for kasan memory initialization
riscv: Improve kasan definitions
riscv: Get rid of MAX_EARLY_MAPPING_SIZE
soc: canaan: Sort the Makefile alphabetically
riscv: Disable KSAN_SANITIZE for vDSO
riscv: Remove unnecessary declaration
riscv: Add Canaan Kendryte K210 SD card defconfig
riscv: Update Canaan Kendryte K210 defconfig
riscv: Add Kendryte KD233 board device tree
riscv: Add SiPeed MAIXDUINO board device tree
riscv: Add SiPeed MAIX GO board device tree
riscv: Add SiPeed MAIX DOCK board device tree
riscv: Add SiPeed MAIX BiT board device tree
riscv: Update Canaan Kendryte K210 device tree
dt-bindings: add resets property to dw-apb-timer
dt-bindings: fix sifive gpio properties
dt-bindings: update sifive uart compatible string
dt-bindings: update sifive clint compatible string
...
Add a clock provider driver for the Canaan Kendryte K210 RISC-V SoC.
This new driver with the compatible string "canaan,k210-clk" implements
support for the full clock structure of the K210 SoC. Since it is
required for the correct operation of the SoC, this driver is
selected by default for compilation when the SOC_CANAAN option is
selected.
With this change, the k210-sysctl driver is turned into a simple
platform driver which enables its power bus clock and triggers
populating its child nodes. The sysctl driver retains the SOC early
initialization code, but the implementation now relies on the new
function k210_clk_early_init() provided by the new clk-k210 driver.
The clock structure implemented and many of the coding ideas for the
driver come from the work by Sean Anderson on the K210 support for the
U-Boot project.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Allow COMPILE_TEST to also build the MStar clk drivers
instead of only building them when ARCH_MSTARV7 is selected.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20210215115710.3762276-1-daniel@0x0f.com
[sboyd@kernel.org: Drop regmap select too]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds a basic driver for the MPLL block found in MStar/SigmaStar
ARMv7 SoCs.
Currently this driver is only good for calculating the rates of it's
outputs and the actual configuration must be done before the kernel
boots. Usually this is done even before u-boot starts.
This driver targets the MPLL block found in the MSC313/MSC313E but
there is no documentation this chip so the register descriptions for
the another MStar chip the MST786 were used as they seem to match.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20210211052206.2955988-5-daniel@0x0f.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The ST-Ericsson U300 platform is getting removed, so this driver is no
longer needed.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120131026.1721788-5-arnd@kernel.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120131026.1721788-4-arnd@kernel.org
Acked-by: Barry Song <baohua@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The zte zx platform is getting removed, so this driver is no
longer needed.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120131026.1721788-3-arnd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The tango platform is getting removed, so the driver is no
longer needed.
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120131026.1721788-2-arnd@kernel.org
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The xlnx_vcu driver is actually a clock controller driver which provides
clocks that can be used by a driver for the encoder/decoder units. There
is no reason to keep this driver in soc. Move the driver to clk.
NOTE: The register mapping actually contains registers for AXI
performance monitoring, but these are not used by the driver.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20210121071659.1226489-16-m.tretter@pengutronix.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the FlexSPI clock on Freescale Layerscape SoCs. The
clock is a simple divider based one and is located inside the device
configuration space (DCFG).
This will allow switching the SCK frequencies for the FlexSPI interface
on the LS1028A and the LX2160A.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20201108185113.31377-8-michael@walle.cc
[sboyd@kernel.org: Drop modalias, add module table]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
function that isn't used anymore. Otherwise the main new thing for the common
clk framework is that it is selectable in the Kconfig language now. Hopefully
this will let clk drivers and clk consumers be testable on more than the
architectures that support the clk framework. The goal is to introduce some
Kunit tests for the framework.
Outside of the core framework we have the usual set of various driver updates
and non-critical fixes. The dirstat shows that the new Baikal-T1 driver is the
largest addition this time around in terms of lines of code. After that the x86
(Intel), Qualcomm, and Mediatek drivers introduce many lines to support new or
upcoming SoCs. After that the dirstat shows the usual suspects working on their
SoC support by fixing minor bugs, correcting data and converting some of their
DT bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix clock support
on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and clk-pllv3
drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support aarch32 mode on
aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using composite
clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102 defined
bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+
-----BEGIN PGP SIGNATURE-----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=nuG5
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time around we have four lines of diff in the core framework,
removing a function that isn't used anymore. Otherwise the main new
thing for the common clk framework is that it is selectable in the
Kconfig language now. Hopefully this will let clk drivers and clk
consumers be testable on more than the architectures that support the
clk framework. The goal is to introduce some Kunit tests for the
framework.
Outside of the core framework we have the usual set of various driver
updates and non-critical fixes. The dirstat shows that the new
Baikal-T1 driver is the largest addition this time around in terms of
lines of code. After that the x86 (Intel), Qualcomm, and Mediatek
drivers introduce many lines to support new or upcoming SoCs. After
that the dirstat shows the usual suspects working on their SoC support
by fixing minor bugs, correcting data and converting some of their DT
bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix
clock support on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and
clk-pllv3 drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support
aarch32 mode on aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using
composite clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102
defined bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on
Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (155 commits)
clk: mediatek: Remove ifr{0,1}_cfg_regs structures
clk: baikal-t1: remove redundant assignment to variable 'divider'
clk: baikal-t1: fix spelling mistake "Uncompatible" -> "Incompatible"
dt-bindings: clock: Add a missing include to MMP Audio Clock binding
dt: Add bindings for IDT VersaClock 5P49V5925
clk: vc5: Add support for IDT VersaClock 5P49V6965
clk: Add Baikal-T1 CCU Dividers driver
clk: Add Baikal-T1 CCU PLLs driver
dt-bindings: clk: Add Baikal-T1 CCU Dividers binding
dt-bindings: clk: Add Baikal-T1 CCU PLLs binding
clk: mediatek: assign the initial value to clk_init_data of mtk_mux
clk: mediatek: Add MT6765 clock support
clk: mediatek: add mt6765 clock IDs
dt-bindings: clock: mediatek: document clk bindings vcodecsys for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings mipi0a for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings for Mediatek MT6765 SoC
CLK: HSDK: CGU: add support for 148.5MHz clock
CLK: HSDK: CGU: support PLL bypassing
CLK: HSDK: CGU: check if PLL is bypassed first
clk: clk-si5341: Add support for the Si5345 series
...
These are updates to SoC specific drivers that did not have
another subsystem maintainer tree to go through for some
reason:
- Some bus and memory drivers for the MIPS P5600 based
Baikal-T1 SoC that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3,
Qualcomm MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas
RZ/G1H, and Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC
as a transport.
- Mediatek platforms now use a new driver for their "MMSYS"
hardware block that controls clocks and some other aspects
in behalf of the media and gpu drivers.
- Some Tegra processors have improved power management
support, including getting woken up by the PMIC and cluster
power down during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon,
Mediatek, and Tegra.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=44Jc
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM/SoC driver updates from Arnd Bergmann:
"These are updates to SoC specific drivers that did not have another
subsystem maintainer tree to go through for some reason:
- Some bus and memory drivers for the MIPS P5600 based Baikal-T1 SoC
that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3, Qualcomm
MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas RZ/G1H, and
Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC as a
transport.
- Mediatek platforms now use a new driver for their "MMSYS" hardware
block that controls clocks and some other aspects in behalf of the
media and gpu drivers.
- Some Tegra processors have improved power management support,
including getting woken up by the PMIC and cluster power down
during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon, Mediatek, and
Tegra"
* tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (155 commits)
clk: sprd: fix compile-testing
bus: bt1-axi: Build the driver into the kernel
bus: bt1-apb: Build the driver into the kernel
bus: bt1-axi: Use sysfs_streq instead of strncmp
bus: bt1-axi: Optimize the return points in the driver
bus: bt1-apb: Use sysfs_streq instead of strncmp
bus: bt1-apb: Use PTR_ERR_OR_ZERO to return from request-regs method
bus: bt1-apb: Fix show/store callback identations
bus: bt1-apb: Include linux/io.h
dt-bindings: memory: Add Baikal-T1 L2-cache Control Block binding
memory: Add Baikal-T1 L2-cache Control Block driver
bus: Add Baikal-T1 APB-bus driver
bus: Add Baikal-T1 AXI-bus driver
dt-bindings: bus: Add Baikal-T1 APB-bus binding
dt-bindings: bus: Add Baikal-T1 AXI-bus binding
staging: tegra-video: fix V4L2 dependency
tee: fix crypto select
drivers: soc: ti: knav_qmss_queue: Make knav_gp_range_ops static
soc: ti: add k3 platforms chipid module driver
dt-bindings: soc: ti: add binding for k3 platforms chipid module
...
I got a build failure with CONFIG_ARCH_SPRD=m when the
main portion of the clock driver failed to get linked into
the kernel:
ERROR: modpost: "sprd_pll_sc_gate_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_pll_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_div_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_comp_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_mux_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_gate_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_sc_gate_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_clk_probe" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_clk_regmap_init" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_pll_ops" [drivers/clk/sprd/sc9860-clk.ko] undefined!
ERROR: modpost: "sprd_div_ops" [drivers/clk/sprd/sc9860-clk.ko] undefined!
ERROR: modpost: "sprd_mux_ops" [drivers/clk/sprd/sc9860-clk.ko] undefined!
This is a combination of two trivial bugs:
- A platform should not be 'tristate', it should be a 'bool' symbol
like the other platforms, if only for consistency, and to avoid
surprises like this one.
- The clk Makefile does not traverse into the sprd subdirectory
if the platform is disabled but the drivers are enabled for
compile-testing.
Fixing either of the two would be sufficient to address the link failure,
but for correctness, both need to be changed.
Fixes: 2b1b799d76 ("arm64: change ARCH_SPRD Kconfig to tristate")
Fixes: d41f59fd92 ("clk: sprd: Add common infrastructure")
Acked-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Baikal-T1 is supposed to be supplied with a high-frequency external
oscillator. But in order to create signals suitable for each IP-block
embedded into the SoC the oscillator output is primarily connected to
a set of CCU PLLs. There are five of them to create clocks for the MIPS
P5600 cores, an embedded DDR controller, SATA, Ethernet and PCIe domains.
The last three domains though named by the biggest system interfaces in
fact include nearly all of the rest SoC peripherals. Each of the PLLs is
based on True Circuits TSMC CLN28HPM IP-core with an interface wrapper
(so called safe PLL' clocks switcher) to simplify the PLL configuration
procedure.
This driver creates the of-based hardware clocks to use them then in
the corresponding subsystems. In order to simplify the driver code we
split the functionality up into the PLLs clocks operations and hardware
clocks declaration/registration procedures.
Even though the PLLs are based on the same IP-core, they may have some
differences. In particular, some CCU PLLs support the output clock change
without gating them (like CPU or PCIe PLLs), while the others don't, some
CCU PLLs are critical and aren't supposed to be gated. In order to cover
all of these cases the hardware clocks driver is designed with an
info-descriptor pattern. So there are special static descriptors declared
for each PLL, which is then used to create a hardware clock with proper
operations. Additionally debugfs-files are provided for each PLL' field
to make sure the implemented rate-PLLs-dividers calculation algorithm is
correct.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200526222056.18072-4-Sergey.Semin@baikalelectronics.ru
[sboyd@kernel.org: Silence sparse warning about initializing structs
with NULL vs. integer]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For the most part the Agilex clock structure is very similar to
Stratix10, so we re-use most of the Stratix10 clock driver.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lkml.kernel.org/r/20200512181647.5071-5-dinguyen@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
CONFIG_COMMON_CLK_VERSATILE doesn't really do anything other than hiding
Arm Ltd reference platform clock drivers. It is both selected by the
platforms that need it and has a 'depends on' for those platforms. Let's
drop the selects and convert CONFIG_COMMON_CLK_VERSATILE into a
menuconfig entry. With this make CONFIG_ICST visible.
Move the 'select REGMAP_MMIO' to the drivers that require it (SP810 did
not).
This also has the side effect of enabling CONFIG_ICST for COMPILE_TEST
as it was not visible before.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Fixes for clk controllers on qcom msm8998 SoCs
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Adjust composite clk to new way of describing clk parents
- Add a driver for BCLK of Freescale SAI cores
* clk-imx: (32 commits)
clk: imx: Add support for i.MX8MP clock driver
dt-bindings: imx: Add clock binding doc for i.MX8MP
clk: imx: gate4: Switch imx_clk_gate4_flags() to clk_hw based API
clk: imx: imx8mq: Switch to clk_hw based API
clk: imx: imx8mm: Switch to clk_hw based API
clk: imx: imx8mn: Switch to clk_hw based API
clk: imx: Remove __init for imx_obtain_fixed_clk_hw() API
clk: imx: gate3: Switch to clk_hw based API
clk: imx: add hw API imx_clk_hw_mux2_flags
clk: imx: add imx_unregister_hw_clocks
clk: imx: clk-composite-8m: Switch to clk_hw based API
clk: imx: clk-pll14xx: Switch to clk_hw based API
clk: imx7up: Rename the clks to hws
clk: imx: Rename the imx_clk_divider_gate to imply it's clk_hw based
clk: imx: Rename the imx_clk_pfdv2 to imply it's clk_hw based
clk: imx: Rename the imx_clk_pllv4 to imply it's clk_hw based
clk: imx: Rename sccg and frac pll register to suggest clk_hw
clk: imx: imx7ulp composite: Rename to show is clk_hw based
clk: imx: pllv2: Switch to clk_hw based API
clk: imx: pllv1: Switch to clk_hw based API
...
* clk-ti:
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
clk: ti: dra7: fix parent for gmac_clkctrl
clk: ti: dra7: add vpe clkctrl data
clk: ti: dra7: add cam clkctrl data
dt-bindings: clock: Move ti-dra7-atl.h to dt-bindings/clock
* clk-xilinx:
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
* clk-nvidia:
clk: tegra20/30: Explicitly set parent clock for Video Decoder
clk: tegra20/30: Don't pre-initialize displays parent clock
clk: tegra: divider: Check UART's divider enable-bit state on rate's recalculation
clk: tegra: clk-dfll: Remove call to pm_runtime_irq_safe()
clk: tegra: Mark fuse clock as critical
* clk-qcom: (35 commits)
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: qcom: Add ipq6018 Global Clock Controller support
clk: qcom: Add DT bindings for ipq6018 gcc clock controller
clk: qcom: gcc-msm8996: Fix parent for CLKREF clocks
clk: qcom: rpmh: Add IPA clock for SC7180
clk: qcom: rpmh: skip undefined clocks when registering
clk: qcom: Add video clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Video clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM VIDEOCC clock bindings
clk: qcom: Add graphics clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Graphics clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM GPUCC clock bindings
clk: qcom: apcs-msm8916: use clk_parent_data to specify the parent
clk: qcom: Add display clock controller driver for SC7180
dt-bindings: clock: Introduce QCOM sc7180 display clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM DISPCC clock bindings
clk: qcom: clk-alpha-pll: Add support for Fabia PLL calibration
clk: qcom: alpha-pll: Remove useless read from set rate
...
* clk-freescale:
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
* clk-qoriq:
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
Add clock driver for QorIQ LS1028A Display output interfaces(LCD, DPHY),
as implemented in TSMC CLN28HPM PLL, this PLL supports the programmable
integer division and range of the display output pixel clock's 27-594MHz.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lkml.kernel.org/r/20191213083402.35678-2-wen.he_1@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
With this driver it is possible to use the BCLK pin of the SAI module as
a generic clock output. This is esp. useful if you want to drive a clock
to an audio codec. Because the output only allows integer divider values
the audio codec needs an integrated PLL.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lkml.kernel.org/r/20200102231101.11834-3-michael@walle.cc
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add common clock driver for Bitmain BM1880 SoC. The clock controller on
BM1880 has supplies clocks to all peripherals in the form of gate clocks
and composite clocks (fixed factor + gate).
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lkml.kernel.org/r/20191115162901.17456-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The ast2600 is a new BMC SoC from ASPEED. It contains many more clocks
than the previous iterations, so support is broken out into it's own
driver.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lkml.kernel.org/r/20190825141848.17346-3-joel@jms.id.au
[sboyd@kernel.org: Mark arrays const]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Adds a driver for the Si5341 and Si5340 chips. The driver does not fully
support all features of these chips, but allows the chip to be used
without any support from the "clockbuilder pro" software.
If the chip is preprogrammed, that is, you bought one with some defaults
burned in, or you programmed the NVM in some way, the driver will just
take over the current settings and only change them on demand. Otherwise
the input must be a fixed XTAL in its most basic configuration (no
predividers, no feedback, etc.).
The driver supports dynamic changes of multisynth, output dividers and
enabling or powering down outputs and multisynths.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
[sboyd@kernel.org: Mark some things static, use BIT_ULL for big bits and
ULL for big constants]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- Mark UFS clk as critical on Hi-Silicon hi3660 SoCs
- Support for Cirrus Logic Lochnagar clks
* clk-hisi:
clk: hi3660: Mark clk_gate_ufs_subsys as critical
* clk-lochnagar:
clk: lochnagar: Add support for the Cirrus Logic Lochnagar
clk: lochnagar: Add initial binding documentation
* clk-allwinner:
clk: sunxi-ng: sun5i: Export the MBUS clock
clk: sunxi-ng: a83t: Add pll-video0 as parent of csi-mclk
clk: sunxi-ng: h6: Allow video & vpu clocks to change parent rate
clk: sunxi-ng: h6: Preset hdmi-cec clock parent
clk: sunxi: Add Kconfig options
clk: sunxi-ng: f1c100s: fix USB PHY gate bit offset
clk: sunxi-ng: Allow DE clock to set parent rate
* clk-rockchip:
clk: rockchip: undo several noc and special clocks as critical on rk3288
clk: rockchip: add a COMPOSITE_DIV_OFFSET clock-type
clk: rockchip: Turn on "aclk_dmac1" for suspend on rk3288
clk: rockchip: Limit use of USB PHY clock to USB on rk3288
clk: rockchip: Fix video codec clocks on rk3288
clk: rockchip: Make rkpwm a critical clock on rk3288
clk: rockchip: fix wrong clock definitions for rk3328
* clk-qoriq:
clk: qoriq: increase array size of cmux_to_group
dt-bindings: qoriq-clock: Add ls1028a chip compatible string
clk: qoriq: Add ls1028a clock configuration
clk: qoriq: add more PLL divider clocks support
dt-bindings: qoriq-clock: add more PLL divider clocks support
Add driver code for the SiFive FU540 PRCI IP block. This IP block
handles reset and clock control for the SiFive FU540 device and
implements SoC-level clock tree controls and dividers.
Based on code written by Wesley Terpstra <wesley@sifive.com>:
999529edf5
Boot and PLL rate change were tested on a SiFive HiFive Unleashed
board.
This version includes several changes requested by Stephen Boyd
<sboyd@kernel.org>.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Wesley W. Terpstra <wesley@sifive.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Megan Wachs <megan@sifive.com>
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-clk@vger.kernel.org
[sboyd@kernel.org: Fix some const and ARRAY_SIZE() issues, make makefile
only descend if CLK_SIFIVE=y]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add common library code for the Analog Bits Wide-Range PLL (WRPLL) IP
block, as implemented in TSMC CLN28HPC.
There is no bus interface or register target associated with this PLL.
This library is intended to be used by drivers for IP blocks that
expose registers connected to the PLL configuration and status
signals.
Based on code originally written by Wesley Terpstra
<wesley@sifive.com>:
999529edf5
This version incorporates several changes requested by Stephen
Boyd <sboyd@kernel.org>.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Wesley Terpstra <wesley@sifive.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Megan Wachs <megan@sifive.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
[sboyd@kernel.org: Fix some const issues]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The M10V of the Milbeaut SoCs has an on-chip controller that derive
mostly clocks from a single external clock, using PLLs, dividers,
multiplexers and gates. Since the PLLs have already been started and
will not stop / restart, they are fixed factor. The gates will be added
in later patch (all of the gates are off state now).
Signed-off-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform. This driver supports the board
controller chip on the Lochnagar board.
The Lochnagar can take several input clocks from the host system,
provides several of its own clock sources, and provides extensive
routing options for those clocks to be supplied to the attached
CODEC/Amp device.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use CONFIG_ARCH_MESON to let make enter the meson clock directory.
As part of a rework, CONFIG_COMMON_CLK_AMLOGIC is about to be removed.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20190201125841.26785-3-jbrunet@baylibre.com
This patch adds a driver for Fixed MMIO clock.
The driver reads a clock frequency value from a single 32-bit memory
mapped register and registers it as a fixed rate clock.
It can be enabled with COMMON_CLK_FIXED_MMIO Kconfig option.
Signed-off-by: Jan Kotas <jank@cadence.com>
[sboyd@kernel.org: Make of_fixed_mmio_clk_setup() static, use clk_hw
based APIs]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The patch introduces CONFIG_MXC_CLK option for legacy MMIO clocks,
this is required to compile legacy MMIO clock conditionally when adding
SCU based clocks for MX8 platforms later.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
ROHM bd71837 and bd71847 contain 32768Hz clock gate. Support the clock
using generic clock framework. Note, only bd71837 is tested but bd71847
should be identical what comes to clk parts.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
because of summer time holidays/vacations. The biggest change in the diffstat
is in the Qualcomm clk driver, where they got support for CPUs and handful of
SoCs. After that, the at91 driver got a major rewrite for newer DT bindings
that should make things easier going forward and the TI code moved to a
clockdomain based design. The long tail is mostly small driver updates for
newer clks and some simpler SoC clock drivers such as the Hisilicon and imx
support.
In the core framework, we only have two small changes this time. One is a new
clk API to get all clks for a device with the bulk clk APIs. This allows
drivers that don't care about doing anything besides turning on all the clks to
just clk_get() them all and turn them on. The other change is the beginning of
a way to support save and restore of clk settings in the clk framework. TI is
the only user right now, but we will want to expand upon this design in the
future to support more save and restore of clk registers. At least this gets
us started and works well enough for one SoC, but there's more work in the
future.
Core:
- clk_bulk_get_all() API and friends to get all the clks for a device
- Basic clk state save/restore hooks
New Drivers:
- Renesas RZ/A2 (R7S9210) SoC, including early clocks
- Rensas RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs
- Rensas RZ/G2M (r8a774a1) SoC
- Qualcomm Krait CPU clk support
- Qualcomm QCS404 GCC support
- Qualcomm SDM660 GCC support
- Qualcomm SDM845 camera clock controller
- Ingenic jz4725b CGU
- Hisilicon 3670 SoC support
- TI SCI clks on K3 SoCs
- iMX6 MMDC clks
- Reset Controller (RMU) support for Actions Semi Owl S900 and S700 SoCs
Updates:
- Rework at91 PMC clock driver for new DT bindings
- Nvidia Tegra clk driver MBIST workaround fix
- S2RAM support for Marvell mvebu periph clks
- Use updated printk format for OF node names
- Fix TI code to only search DT subnodes
- Various static analysis finds
- Tag various drivers with SPDX license tags
- Support dynamic frequency switching (DFS) on qcom SDM845 GCC
- Only use s2mps11 dt-binding defines instead of redefining them in the driver
- Add some more missing clks to qcom MSM8996 GCC
- Quad SPI clks on qcom SDM845
- Add support for CMT timer clocks on R-Car V3H
- Add support for SHDI and various timer clocks on R-Car V3M
- Improve OSC and RCLK (watchdog) handling on R-Car Gen3 SoCs
- Amlogic clk-pll driver improvements and updates
- Amlogic axg audio controller system clocks
- Register Amlogic meson8b clock controller early
- Add support for SATA and Fine Display Processor (FDP) clocks on R-Car M3-N
- Consolidation of system suspend related code in Exynos, S5P, S3C SoC clk drivers
- Fixes for system suspend support on Exynos542x (Odroid boards) and Exynos5433 SoC
- Remove obsoleted Exynos4212 ISP clock definitions
- Migrated TI am3/4/5 and dra7 SoCs to clockdomain based design
- TI RTC+DDR sleep mode support for clock save/restore
- Allwinner A64 display engine support and fixes
- Allwinner A83t display engine support and fixes
-----BEGIN PGP SIGNATURE-----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=V5aK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time it looks like a quieter release cycle in the clk tree. I
guess that's because of summer time holidays/vacations. The biggest
change in the diffstat is in the Qualcomm clk driver, where they got
support for CPUs and handful of SoCs. After that, the at91 driver got
a major rewrite for newer DT bindings that should make things easier
going forward and the TI code moved to a clockdomain based design.
The long tail is mostly small driver updates for newer clks and some
simpler SoC clock drivers such as the Hisilicon and imx support.
In the core framework, we only have two small changes this time.
One is a new clk API to get all clks for a device with the bulk clk
APIs. This allows drivers that don't care about doing anything besides
turning on all the clks to just clk_get() them all and turn them on.
The other change is the beginning of a way to support save and restore
of clk settings in the clk framework. TI is the only user right now,
but we will want to expand upon this design in the future to support
more save and restore of clk registers. At least this gets us started
and works well enough for one SoC, but there's more work in the
future.
Core:
- clk_bulk_get_all() API and friends to get all the clks for a device
- Basic clk state save/restore hooks
New Drivers:
- Renesas RZ/A2 (R7S9210) SoC, including early clocks
- Rensas RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs
- Rensas RZ/G2M (r8a774a1) SoC
- Qualcomm Krait CPU clk support
- Qualcomm QCS404 GCC support
- Qualcomm SDM660 GCC support
- Qualcomm SDM845 camera clock controller
- Ingenic jz4725b CGU
- Hisilicon 3670 SoC support
- TI SCI clks on K3 SoCs
- iMX6 MMDC clks
- Reset Controller (RMU) support for Actions Semi Owl S900 and S700 SoCs
Updates:
- Rework at91 PMC clock driver for new DT bindings
- Nvidia Tegra clk driver MBIST workaround fix
- S2RAM support for Marvell mvebu periph clks
- Use updated printk format for OF node names
- Fix TI code to only search DT subnodes
- Various static analysis finds
- Tag various drivers with SPDX license tags
- Support dynamic frequency switching (DFS) on qcom SDM845 GCC
- Only use s2mps11 dt-binding defines instead of redefining them in the driver
- Add some more missing clks to qcom MSM8996 GCC
- Quad SPI clks on qcom SDM845
- Add support for CMT timer clocks on R-Car V3H
- Add support for SHDI and various timer clocks on R-Car V3M
- Improve OSC and RCLK (watchdog) handling on R-Car Gen3 SoCs
- Amlogic clk-pll driver improvements and updates
- Amlogic axg audio controller system clocks
- Register Amlogic meson8b clock controller early
- Add support for SATA and Fine Display Processor (FDP) clocks on R-Car M3-N
- Consolidation of system suspend related code in Exynos, S5P, S3C SoC clk drivers
- Fixes for system suspend support on Exynos542x (Odroid boards) and Exynos5433 SoC
- Remove obsoleted Exynos4212 ISP clock definitions
- Migrated TI am3/4/5 and dra7 SoCs to clockdomain based design
- TI RTC+DDR sleep mode support for clock save/restore
- Allwinner A64 display engine support and fixes
- Allwinner A83t display engine support and fixes"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (186 commits)
clk: qcom: Remove unused arrays in SDM845 GCC
clk: fixed-rate: fix of_node_get-put imbalance
clk: s2mps11: Add used attribute to s2mps11_dt_match
clk: qcom: gcc-sdm660: Add MODULE_LICENSE
clk: qcom: Add safe switch hook for krait mux clocks
dt-bindings: clock: Document qcom,krait-cc
clk: qcom: Add Krait clock controller driver
dt-bindings: arm: Document qcom,kpss-gcc
clk: qcom: Add KPSS ACC/GCC driver
clk: qcom: Add support for Krait clocks
clk: qcom: Add IPQ806X's HFPLLs
clk: qcom: Add MSM8960/APQ8064's HFPLLs
dt-bindings: clock: Document qcom,hfpll
clk: qcom: Add HFPLL driver
clk: qcom: Add support for High-Frequency PLLs (HFPLLs)
ARM: Add Krait L2 register accessor functions
clk: imx6q: add mmdc0 ipg clock
clk: imx6sl: add mmdc ipg clocks
clk: imx6sll: add mmdc1 ipg clock
clk: imx6sx: add mmdc1 ipg clock
...
