We'll need this to handle ICMP errors for tunnels without a sending socket
(i.e. FoU and GUE). There, we might have to look up different types of IP
tunnels, registered as network protocols, before we get a match, so we
want this for the error handlers of IPPROTO_IPIP and IPPROTO_IPV6 in both
inet_protos and inet6_protos. These error codes will be used in the next
patch.
For consistency, return sensible error codes in protocol error handlers
whenever handlers can't handle errors because, even if valid, they don't
match a protocol or any of its states.
This has no effect on existing error handling paths.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For both IPv4 and IPv6, if we can't match errors to a socket, try
tunnels before ignoring them. Look up a socket with the original source
and destination ports as found in the UDP packet inside the ICMP payload,
this will work for tunnels that force the same destination port for both
endpoints, i.e. VXLAN and GENEVE.
Actually, lwtunnels could break this assumption if they are configured by
an external control plane to have different destination ports on the
endpoints: in this case, we won't be able to trace ICMP messages back to
them.
For IPv6 redirect messages, call ip6_redirect() directly with the output
interface argument set to the interface we received the packet from (as
it's the very interface we should build the exception on), otherwise the
new nexthop will be rejected. There's no such need for IPv4.
Tunnels can now export an encap_err_lookup() operation that indicates a
match. Pass the packet to the lookup function, and if the tunnel driver
reports a matching association, continue with regular ICMP error handling.
v2:
- Added newline between network and transport header sets in
__udp{4,6}_lib_err_encap() (David Miller)
- Removed redundant skb_reset_network_header(skb); in
__udp4_lib_err_encap()
- Removed redundant reassignment of iph in __udp4_lib_err_encap()
(Sabrina Dubroca)
- Edited comment to __udp{4,6}_lib_err_encap() to reflect the fact this
won't work with lwtunnels configured to use asymmetric ports. By the way,
it's VXLAN, not VxLAN (Jiri Benc)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the backlog earlier in inet_dccp_listen() and inet_listen(),
then we can avoid the redundant setting.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some scenarios, the GRO engine can assemble an UDP GRO packet
that ultimately lands on a non GRO-enabled socket.
This patch tries to address the issue explicitly checking for the UDP
socket features before enqueuing the packet, and eventually segmenting
the unexpected GRO packet, as needed.
We must also cope with re-insertion requests: after segmentation the
UDP code calls the helper introduced by the previous patches, as needed.
Segmentation is performed by a common helper, which takes care of
updating socket and protocol stats is case of failure.
rfc v3 -> v1
- fix compile issues with rxrpc
- when gso_segment returns NULL, treat is as an error
- added 'ipv4' argument to udp_rcv_segment()
rfc v2 -> rfc v3
- moved udp_rcv_segment() into net/udp.h, account errors to socket
and ns, always return NULL or segs list
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that we can re-use it at the UDP level in a later patch
rfc v3 -> v1
- add the helper declaration into the ip header
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When UDP GRO is enabled, the UDP_GRO cmsg will carry the ingress
datagram size. User-space can use such info to compute the original
packets layout.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the RX counterpart of commit bec1f6f697 ("udp: generate gso
with UDP_SEGMENT"). When UDP_GRO is enabled, such socket is also
eligible for GRO in the rx path: UDP segments directed to such socket
are assembled into a larger GSO_UDP_L4 packet.
The core UDP GRO support is enabled with setsockopt(UDP_GRO).
Initial benchmark numbers:
Before:
udp rx: 1079 MB/s 769065 calls/s
After:
udp rx: 1466 MB/s 24877 calls/s
This change introduces a side effect in respect to UDP tunnels:
after a UDP tunnel creation, now the kernel performs a lookup per ingress
UDP packet, while before such lookup happened only if the ingress packet
carried a valid internal header csum.
rfc v2 -> rfc v3:
- fixed typos in macro name and comments
- really enforce UDP_GRO_CNT_MAX, instead of UDP_GRO_CNT_MAX + 1
- acquire socket lock in UDP_GRO setsockopt
rfc v1 -> rfc v2:
- use a new option to enable UDP GRO
- use static keys to protect the UDP GRO socket lookup
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The *encap_needed static keys are enabled by UDP tunnels
and several UDP encapsulations type, but they are never
turned off. This can cause unneeded overall performance
degradation for systems where such features are used
transiently.
This patch introduces complete book-keeping for such keys,
decreasing the usage at socket destruction time, if needed,
and avoiding that the same socket could increase the key
usage multiple times.
rfc v3 -> v1:
- add socket lock around udp_tunnel_encap_enable()
rfc v2 -> rfc v3:
- use udp_tunnel_encap_enable() in setsockopt()
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there exist a pair of raw sockets one unbound and one bound
to a VRF but equal in all other respects, when a packet is received
in the VRF context, __raw_v4_lookup() matches on both sockets.
This results in the packet being delivered over both sockets,
instead of only the raw socket bound to the VRF. The bound device
checks in __raw_v4_lookup() are replaced with a call to
raw_sk_bound_dev_eq() which correctly handles whether the packet
should be delivered over the unbound socket in such cases.
In __raw_v6_lookup() the match on the device binding of the socket is
similarly updated to use raw_sk_bound_dev_eq() which matches the
handling in __raw_v4_lookup().
Importantly raw_sk_bound_dev_eq() takes the raw_l3mdev_accept sysctl
into account.
Signed-off-by: Duncan Eastoe <deastoe@vyatta.att-mail.com>
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a sysctl raw_l3mdev_accept to control raw socket lookup in a manner
similar to use of tcp_l3mdev_accept for stream and of udp_l3mdev_accept
for datagram sockets. Have this default to enabled for reasons of
backwards compatibility. This is so as to specify the output device
with cmsg and IP_PKTINFO, but using a socket not bound to the
corresponding VRF. This allows e.g. older ping implementations to be
run with specifying the device but without executing it in the VRF.
If the option is disabled, packets received in a VRF context are only
handled by a raw socket bound to the VRF, and correspondingly packets
in the default VRF are only handled by a socket not bound to any VRF.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure an unbound datagram skt is chosen when not in a VRF. The check
for a device match in compute_score() for UDP must be performed when
there is no device match. For this, a failure is returned when there is
no device match. This ensures that bound sockets are never selected,
even if there is no unbound socket.
Allow IPv6 packets to be sent over a datagram skt bound to a VRF. These
packets are currently blocked, as flowi6_oif was set to that of the
master vrf device, and the ipi6_ifindex is that of the slave device.
Allow these packets to be sent by checking the device with ipi6_ifindex
has the same L3 scope as that of the bound device of the skt, which is
the master vrf device. Note that this check always succeeds if the skt
is unbound.
Even though the right datagram skt is now selected by compute_score(),
a different skt is being returned that is bound to the wrong vrf. The
difference between these and stream sockets is the handling of the skt
option for SO_REUSEPORT. While the handling when adding a skt for reuse
correctly checks that the bound device of the skt is a match, the skts
in the hashslot are already incorrect. So for the same hash, a skt for
the wrong vrf may be selected for the required port. The root cause is
that the skt is immediately placed into a slot when it is created,
but when the skt is then bound using SO_BINDTODEVICE, it remains in the
same slot. The solution is to move the skt to the correct slot by
forcing a rehash.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit a04a480d43 ("net: Require exact match for TCP socket
lookups if dif is l3mdev") only ensures that the correct socket is
selected for packets in a VRF. However, there is no guarantee that
the unbound socket will be selected for packets when not in a VRF.
By checking for a device match in compute_score() also for the case
when there is no bound device and attaching a score to this, the
unbound socket is selected. And if a failure is returned when there
is no device match, this ensures that bound sockets are never selected,
even if there is no unbound socket.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the inet socket lookup to avoid packets arriving on a device
enslaved to an l3mdev from matching unbound sockets by removing the
wildcard for non sk_bound_dev_if and instead relying on check against
the secondary device index, which will be 0 when the input device is
not enslaved to an l3mdev and so match against an unbound socket and
not match when the input device is enslaved.
Change the socket binding to take the l3mdev into account to allow an
unbound socket to not conflict sockets bound to an l3mdev given the
datapath isolation now guaranteed.
Signed-off-by: Robert Shearman <rshearma@vyatta.att-mail.com>
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack argument to ip_fib_metrics_init and add messages for invalid
metrics.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack arg to rtnl_create_link and add messages for invalid
number of Tx or Rx queues.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When iptables command is executed, ip_{set/get}sockopt() try to upload
bpfilter.ko if bpfilter is enabled. if it couldn't find bpfilter.ko,
command is failed.
bpfilter.ko is generated if CONFIG_BPFILTER_UMH is enabled.
ip_{set/get}sockopt() only checks CONFIG_BPFILTER.
So that if CONFIG_BPFILTER is enabled and CONFIG_BPFILTER_UMH is disabled,
iptables command is always failed.
test config:
CONFIG_BPFILTER=y
# CONFIG_BPFILTER_UMH is not set
test command:
%iptables -L
iptables: No chain/target/match by that name.
Fixes: d2ba09c17a ("net: add skeleton of bpfilter kernel module")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most callers of pskb_trim_rcsum() simply drop the skb when
it fails, however, ip_check_defrag() still continues to pass
the skb up to stack. This is suspicious.
In ip_check_defrag(), after we learn the skb is an IP fragment,
passing the skb to callers makes no sense, because callers expect
fragments are defrag'ed on success. So, dropping the skb when we
can't defrag it is reasonable.
Note, prior to commit 88078d98d1, this is not a big problem as
checksum will be fixed up anyway. After it, the checksum is not
correct on failure.
Found this during code review.
Fixes: 88078d98d1 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) BPF verifier fixes from Daniel Borkmann.
2) HNS driver fixes from Huazhong Tan.
3) FDB only works for ethernet devices, reject attempts to install FDB
rules for others. From Ido Schimmel.
4) Fix spectre V1 in vhost, from Jason Wang.
5) Don't pass on-stack object to irq_set_affinity_hint() in mvpp2
driver, from Marc Zyngier.
6) Fix mlx5e checksum handling when RXFCS is enabled, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (49 commits)
openvswitch: Fix push/pop ethernet validation
net: stmmac: Fix stmmac_mdio_reset() when building stmmac as modules
bpf: test make sure to run unpriv test cases in test_verifier
bpf: add various test cases to test_verifier
bpf: don't set id on after map lookup with ptr_to_map_val return
bpf: fix partial copy of map_ptr when dst is scalar
libbpf: Fix compile error in libbpf_attach_type_by_name
kselftests/bpf: use ping6 as the default ipv6 ping binary if it exists
selftests: mlxsw: qos_mc_aware: Add a test for UC awareness
selftests: mlxsw: qos_mc_aware: Tweak for min shaper
mlxsw: spectrum: Set minimum shaper on MC TCs
mlxsw: reg: QEEC: Add minimum shaper fields
net: hns3: bugfix for rtnl_lock's range in the hclgevf_reset()
net: hns3: bugfix for rtnl_lock's range in the hclge_reset()
net: hns3: bugfix for handling mailbox while the command queue reinitialized
net: hns3: fix incorrect return value/type of some functions
net: hns3: bugfix for hclge_mdio_write and hclge_mdio_read
net: hns3: bugfix for is_valid_csq_clean_head()
net: hns3: remove unnecessary queue reset in the hns3_uninit_all_ring()
net: hns3: bugfix for the initialization of command queue's spin lock
...
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We return 0 in the case of a nonblocking socket that has no data
available. However, this is incorrect and may confuse applications.
After this patch we do the correct thing and return the error
EAGAIN.
Quoting return codes from recvmsg manpage,
EAGAIN or EWOULDBLOCK
The socket is marked nonblocking and the receive operation would
block, or a receive timeout had been set and the timeout expired
before data was received.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Similiar with ipv6 mcast commit 89225d1ce6 ("net: ipv6: mld: fix v1/v2
switchback timeout to rfc3810, 9.12.")
i) RFC3376 8.12. Older Version Querier Present Timeout says:
The Older Version Querier Interval is the time-out for transitioning
a host back to IGMPv3 mode once an older version query is heard.
When an older version query is received, hosts set their Older
Version Querier Present Timer to Older Version Querier Interval.
This value MUST be ((the Robustness Variable) times (the Query
Interval in the last Query received)) plus (one Query Response
Interval).
Currently we only use a hardcode value IGMP_V1/v2_ROUTER_PRESENT_TIMEOUT.
Fix it by adding two new items mr_qi(Query Interval) and mr_qri(Query Response
Interval) in struct in_device.
Now we can calculate the switchback time via (mr_qrv * mr_qi) + mr_qri.
We need update these values when receive IGMPv3 queries.
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since its inception, udp_dump_one has had a bug where userspace
needs to swap src and dst addresses and ports in order to find
the socket it wants. This is because it passes the socket source
address to __udp[46]_lib_lookup's saddr argument, but those
functions are intended to find local sockets matching received
packets, so saddr is the remote address, not the local address.
This can no longer be fixed for backwards compatibility reasons,
so add a brief comment explaining that this is the case. This
will avoid confusion and help ensure SOCK_DIAG implementations
of new protocols don't have the same problem.
Fixes: a925aa00a5 ("udp_diag: Implement the get_exact dumping functionality")
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Traceroute executed in a vrf succeeds if no device is given or if the
vrf is given as the device, but fails if the interface is given as the
device. This is for default UDP probes, it succeeds for TCP SYN or ICMP
ECHO probes. As the skb bound dev is the interface and the sk dev is
the vrf, sk lookup fails for ICMP_DEST_UNREACH and ICMP_TIME_EXCEEDED
messages. The solution is for the secondary dev to be passed so that
the interface is available for the device match to succeed, in the same
way as is already done for non-error cases.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cleanup path will put the target net when netnsid is set. So we must
reset netnsid if the input is invalid.
Fixes: d7e38611b8 ("net/ipv4: Put target net when address dump fails due to bad attributes")
Fixes: 242afaa696 ("net/ipv6: Put target net when address dump fails due to bad attributes")
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current handling of CHECKSUM_COMPLETE packets by the UDP stack is
incorrect for any packet that has an incorrect checksum value.
udp4/6_csum_init() will both make a call to
__skb_checksum_validate_complete() to initialize/validate the csum
field when receiving a CHECKSUM_COMPLETE packet. When this packet
fails validation, skb->csum will be overwritten with the pseudoheader
checksum so the packet can be fully validated by software, but the
skb->ip_summed value will be left as CHECKSUM_COMPLETE so that way
the stack can later warn the user about their hardware spewing bad
checksums. Unfortunately, leaving the SKB in this state can cause
problems later on in the checksum calculation.
Since the the packet is still marked as CHECKSUM_COMPLETE,
udp_csum_pull_header() will SUBTRACT the checksum of the UDP header
from skb->csum instead of adding it, leaving us with a garbage value
in that field. Once we try to copy the packet to userspace in the
udp4/6_recvmsg(), we'll make a call to skb_copy_and_csum_datagram_msg()
to checksum the packet data and add it in the garbage skb->csum value
to perform our final validation check.
Since the value we're validating is not the proper checksum, it's possible
that the folded value could come out to 0, causing us not to drop the
packet. Instead, we believe that the packet was checksummed incorrectly
by hardware since skb->ip_summed is still CHECKSUM_COMPLETE, and we attempt
to warn the user with netdev_rx_csum_fault(skb->dev);
Unfortunately, since this is the UDP path, skb->dev has been overwritten
by skb->dev_scratch and is no longer a valid pointer, so we end up
reading invalid memory.
This patch addresses this problem in two ways:
1) Do not use the dev pointer when calling netdev_rx_csum_fault()
from skb_copy_and_csum_datagram_msg(). Since this gets called
from the UDP path where skb->dev has been overwritten, we have
no way of knowing if the pointer is still valid. Also for the
sake of consistency with the other uses of
netdev_rx_csum_fault(), don't attempt to call it if the
packet was checksummed by software.
2) Add better CHECKSUM_COMPLETE handling to udp4/6_csum_init().
If we receive a packet that's CHECKSUM_COMPLETE that fails
verification (i.e. skb->csum_valid == 0), check who performed
the calculation. It's possible that the checksum was done in
software by the network stack earlier (such as Netfilter's
CONNTRACK module), and if that says the checksum is bad,
we can drop the packet immediately instead of waiting until
we try and copy it to userspace. Otherwise, we need to
mark the SKB as CHECKSUM_NONE, since the skb->csum field
no longer contains the full packet checksum after the
call to __skb_checksum_validate_complete().
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Fixes: c84d949057 ("udp: copy skb->truesize in the first cache line")
Cc: Sam Kumar <samanthakumar@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing a route dump across all address families, do not error out
if the table does not exist. This allows a route dump for AF_UNSPEC
with a table id that may only exist for some of the families.
Do return the table does not exist error if dumping routes for a
specific family and the table does not exist.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If tgt_net is set based on IFA_TARGET_NETNSID attribute in the dump
request, make sure all error paths call put_net.
Fixes: 5fcd266a9f ("net/ipv4: Add support for dumping addresses for a specific device")
Fixes: c33078e3df ("net/ipv4: Update inet_dump_ifaddr for strict data checking")
Reported-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With EDT model, SRTT no longer is inflated by pacing delays.
This means that RTO and some other xmit timers might be setup
incorrectly. This is particularly visible with either :
- Very small enforced pacing rates (SO_MAX_PACING_RATE)
- Reduced rto (from the default 200 ms)
This can lead to TCP flows aborts in the worst case,
or spurious retransmits in other cases.
For example, this session gets far more throughput
than the requested 80kbit :
$ netperf -H 127.0.0.2 -l 100 -- -q 10000
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 127.0.0.2 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
540000 262144 262144 104.00 2.66
With the fix :
$ netperf -H 127.0.0.2 -l 100 -- -q 10000
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 127.0.0.2 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
540000 262144 262144 104.00 0.12
EDT allows for better control of rtx timers, since TCP has
a better idea of the earliest departure time of each skb
in the rtx queue. We only have to eventually add to the
timer the difference of the EDT time with current time.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit dd979b4df8.
This broke tcp_poll for SMC fallback: An AF_SMC socket establishes an
internal TCP socket for the initial handshake with the remote peer.
Whenever the SMC connection can not be established this TCP socket is
used as a fallback. All socket operations on the SMC socket are then
forwarded to the TCP socket. In case of poll, the file->private_data
pointer references the SMC socket because the TCP socket has no file
assigned. This causes tcp_poll to wait on the wrong socket.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an RTM_GETADDR dump request has ifa_index set in the ifaddrmsg
header, then return only the addresses for that device.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to IPv6 move the logic that walks over the ipv4 address list
for a device into a helper.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-10-21
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Implement two new kind of BPF maps, that is, queue and stack
map along with new peek, push and pop operations, from Mauricio.
2) Add support for MSG_PEEK flag when redirecting into an ingress
psock sk_msg queue, and add a new helper bpf_msg_push_data() for
insert data into the message, from John.
3) Allow for BPF programs of type BPF_PROG_TYPE_CGROUP_SKB to use
direct packet access for __skb_buff, from Song.
4) Use more lightweight barriers for walking perf ring buffer for
libbpf and perf tool as well. Also, various fixes and improvements
from verifier side, from Daniel.
5) Add per-symbol visibility for DSO in libbpf and hide by default
global symbols such as netlink related functions, from Andrey.
6) Two improvements to nfp's BPF offload to check vNIC capabilities
in case prog is shared with multiple vNICs and to protect against
mis-initializing atomic counters, from Jakub.
7) Fix for bpftool to use 4 context mode for the nfp disassembler,
also from Jakub.
8) Fix a return value comparison in test_libbpf.sh and add several
bpftool improvements in bash completion, documentation of bpf fs
restrictions and batch mode summary print, from Quentin.
9) Fix a file resource leak in BPF selftest's load_kallsyms()
helper, from Peng.
10) Fix an unused variable warning in map_lookup_and_delete_elem(),
from Alexei.
11) Fix bpf_skb_adjust_room() signature in BPF UAPI helper doc,
from Nicolas.
12) Add missing executables to .gitignore in BPF selftests, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next tree:
1) Use lockdep_is_held() in ipset_dereference_protected(), from Lance Roy.
2) Remove unused variable in cttimeout, from YueHaibing.
3) Add ttl option for nft_osf, from Fernando Fernandez Mancera.
4) Use xfrm family to deal with IPv6-in-IPv4 packets from nft_xfrm,
from Florian Westphal.
5) Simplify xt_osf_match_packet().
6) Missing ct helper alias definition in snmp_trap helper, from Taehee Yoo.
7) Remove unnecessary parameter in nf_flow_table_cleanup(), from Taehee Yoo.
8) Remove unused variable definitions in nft_{dup,fwd}, from Weongyo Jeong.
9) Remove empty net/netfilter/nfnetlink_log.h file, from Taehee Yoo.
10) Revert xt_quota updates remain option due to problems in the listing
path for 32-bit arches, from Maze.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched/cls_api.c has overlapping changes to a call to
nlmsg_parse(), one (from 'net') added rtm_tca_policy instead of NULL
to the 5th argument, and another (from 'net-next') added cb->extack
instead of NULL to the 6th argument.
net/ipv4/ipmr_base.c is a case of a bug fix in 'net' being done to
code which moved (to mr_table_dump)) in 'net-next'. Thanks to David
Ahern for the heads up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported the following warning triggered while running CRIU tests:
tcp_clean_rtx_queue()
...
last_ackt = tcp_skb_timestamp_us(skb);
WARN_ON_ONCE(last_ackt == 0);
This is caused by 5f6188a800 ("tcp: do not change tcp_wstamp_ns
in tcp_mstamp_refresh"), as we end up having skbs in retransmit queue
with a zero skb->skb_mstamp_ns field.
We could fix this bug in different ways, like making sure
tp->tcp_wstamp_ns is not zero at socket creation, but as Neal pointed
out, we also do not want that pacing status of a repaired socket
could push tp->tcp_wstamp_ns far ahead in the future.
So we prefer changing tcp_write_xmit() to not call tcp_update_skb_after_send()
and instead do what is requested by TCP_REPAIR logic.
Fixes: 5f6188a800 ("tcp: do not change tcp_wstamp_ns in tcp_mstamp_refresh")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Vagin <avagin@openvz.org>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the skb space ends in an unresolved entry while dumping we'll miss
some unresolved entries. The reason is due to zeroing the entry counter
between dumping resolved and unresolved mfc entries. We should just
keep counting until the whole table is dumped and zero when we move to
the next as we have a separate table counter.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: 8fb472c09b ("ipmr: improve hash scalability")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Centralize the code that sets gains used for computing cwnd and pacing
rate. This simplifies the code and makes it easier to change the state
machine or (in the future) dynamically change the gain values and
ensure that the correct gain values are always used.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust TCP BBR for the new departure time pacing model in the recent
commit ab408b6dc7 ("tcp: switch tcp and sch_fq to new earliest
departure time model").
With TSQ and pacing at lower layers, there are often several skbs
queued in the pacing layer, and thus there is less data "in the
network" than "in flight".
With departure time pacing at lower layers (e.g. fq or potential
future NICs), the data in the pacing layer now has a pre-scheduled
("baked-in") departure time that cannot be changed, even if the
congestion control algorithm decides to use a new pacing rate.
This means that there can be a non-trivial lag between when BBR makes
a pacing rate change and when the inter-skb pacing delays
change. After a pacing rate change, the number of packets in the
network can gradually evolve to be higher or lower, depending on
whether the sending rate is higher or lower than the delivery
rate. Thus ignoring this lag can cause significant overshoot, with the
flow ending up with too many or too few packets in the network.
This commit changes BBR to adapt its pacing rate based on the amount
of data in the network that it estimates has already been "baked in"
by previous departure time decisions. We estimate the number of our
packets that will be in the network at the earliest departure time
(EDT) for the next skb scheduled as:
in_network_at_edt = inflight_at_edt - (EDT - now) * bw
If we're increasing the amount of data in the network ("in_network"),
then we want to know if the transmit of the EDT skb will push
in_network above the target, so our answer includes
bbr_tso_segs_goal() from the skb departing at EDT. If we're decreasing
in_network, then we want to know if in_network will sink too low just
before the EDT transmit, so our answer does not include the segments
from the skb departing at EDT.
Why do we treat pacing_gain > 1.0 case and pacing_gain < 1.0 case
differently? The in_network curve is a step function: in_network goes
up on transmits, and down on ACKs. To accurately predict when
in_network will go beyond our target value, this will happen on
different events, depending on whether we're concerned about
in_network potentially going too high or too low:
o if pushing in_network up (pacing_gain > 1.0),
then in_network goes above target upon a transmit event
o if pushing in_network down (pacing_gain < 1.0),
then in_network goes below target upon an ACK event
This commit changes the BBR state machine to use this estimated
"packets in network" value to make its decisions.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the MSG_PEEK flag when doing redirect to ingress
and receiving on the sk_msg psock queue. Previously the flag was
being ignored which could confuse applications if they expected the
flag to work as normal.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When converting sockmap to new skmsg generic data structures we missed
that the recvmsg handler did not correctly use sg.size and instead was
using individual elements length. The result is if a sock is closed
with outstanding data we omit the call to sk_mem_uncharge() and can
get the warning below.
[ 66.728282] WARNING: CPU: 6 PID: 5783 at net/core/stream.c:206 sk_stream_kill_queues+0x1fa/0x210
To fix this correct the redirect handler to xfer the size along with
the scatterlist and also decrement the size from the recvmsg handler.
Now when a sock is closed the remaining 'size' will be decremented
with sk_mem_uncharge().
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Eric reported that syzkaller triggered a splat in tcp_cleanup_ulp()
where assertion sock_owned_by_me() failed. This happened through
inet_csk_prepare_forced_close() first releasing the socket lock,
then calling into tcp_done(newsk) which is called after the
inet_csk_prepare_forced_close() and therefore without the socket
lock held. The sock_owned_by_me() assertion can generally be
removed as the only place where tcp_cleanup_ulp() is called from
now is out of inet_csk_destroy_sock() -> sk->sk_prot->destroy()
where socket is in dead state and unreachable. Therefore, add a
comment why the check is not needed instead.
Fixes: 8b9088f806 ("tcp, ulp: enforce sock_owned_by_me upon ulp init and cleanup")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to upload helper module automatically, helper alias name
is needed. so that MODULE_ALIAS_NFCT_HELPER() should be added.
And unlike other nat helper modules, the nf_nat_snmp_basic can be
used independently.
helper name is "snmp_trap" so that alias name will be
"nfct-helper-snmp_trap" by MODULE_ALIAS_NFCT_HELPER(snmp_trap)
test command:
%iptables -t raw -I PREROUTING -p udp -j CT --helper snmp_trap
%lsmod | grep nf_nat_snmp_basic
We can see nf_nat_snmp_basic module is uploaded automatically.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Unlike IPv6, IPv4 does not have routes marked with RTF_PREFIX_RT. If the
flag is set in the dump request, just return.
In the process of this change, move the CLONE check to use the new
filter flags.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update parsing of route dump request to enable kernel side filtering.
Allow filtering results by protocol (e.g., which routing daemon installed
the route), route type (e.g., unicast), table id and nexthop device. These
amount to the low hanging fruit, yet a huge improvement, for dumping
routes.
ip_valid_fib_dump_req is called with RTNL held, so __dev_get_by_index can
be used to look up the device index without taking a reference. From
there filter->dev is only used during dump loops with the lock still held.
Set NLM_F_DUMP_FILTERED in the answer_flags so the user knows the results
have been filtered should no entries be returned.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement kernel side filtering of routes by egress device index and
table id. If the table id is given in the filter, lookup table and
call mr_table_dump directly for it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move per-table loops from mr_rtm_dumproute to mr_table_dump and export
mr_table_dump for dumps by specific table id.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement kernel side filtering of routes by table id, egress device index,
protocol and route type. If the table id is given in the filter, lookup the
table and call fib_table_dump directly for it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add struct fib_dump_filter for options on limiting which routes are
returned in a dump request. The current list is table id, protocol,
route type, rtm_flags and nexthop device index. struct net is needed
to lookup the net_device from the index.
Declare the filter for each route dump handler and plumb the new
arguments from dump handlers to ip_valid_fib_dump_req.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-10-16
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Convert BPF sockmap and kTLS to both use a new sk_msg API and enable
sk_msg BPF integration for the latter, from Daniel and John.
2) Enable BPF syscall side to indicate for maps that they do not support
a map lookup operation as opposed to just missing key, from Prashant.
3) Add bpftool map create command which after map creation pins the
map into bpf fs for further processing, from Jakub.
4) Add bpftool support for attaching programs to maps allowing sock_map
and sock_hash to be used from bpftool, from John.
5) Improve syscall BPF map update/delete path for map-in-map types to
wait a RCU grace period for pending references to complete, from Daniel.
6) Couple of follow-up fixes for the BPF socket lookup to get it
enabled also when IPv6 is compiled as a module, from Joe.
7) Fix a generic-XDP bug to handle the case when the Ethernet header
was mangled and thus update skb's protocol and data, from Jesper.
8) Add a missing BTF header length check between header copies from
user space, from Wenwen.
9) Minor fixups in libbpf to use __u32 instead u32 types and include
proper perf_event.h uapi header instead of perf internal one, from Yonghong.
10) Allow to pass user-defined flags through EXTRA_CFLAGS and EXTRA_LDFLAGS
to bpftool's build, from Jiri.
11) BPF kselftest tweaks to add LWTUNNEL to config fragment and to install
with_addr.sh script from flow dissector selftest, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We store in tcp socket a cache of most recent high resolution
clock, there is no need to call local_clock() again, since
this cache is good enough.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a typo in this parameter name.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TCP implements its own pacing (when no fq packet scheduler is used),
it is arming high resolution timer after a packet is sent.
But in many cases (like TCP_RR kind of workloads), this high resolution
timer expires before the application attempts to write the following
packet. This overhead also happens when the flow is ACK clocked and
cwnd limited instead of being limited by the pacing rate.
This leads to extra overhead (high number of IRQ)
Now tcp_wstamp_ns is reserved for the pacing timer only
(after commit "tcp: do not change tcp_wstamp_ns in tcp_mstamp_refresh"),
we can setup the timer only when a packet is about to be sent,
and if tcp_wstamp_ns is in the future.
This leads to a ~10% performance increase in TCP_RR workloads.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit fefa569a9d ("net_sched: sch_fq: account for schedule/timers
drifts") we added a mitigation for scheduling jitter in fq packet scheduler.
This patch does the same in TCP stack, now it is using EDT model.
Note that this mitigation is valid for both external (fq packet scheduler)
or internal TCP pacing.
This uses the same strategy than the above commit, allowing
a time credit of half the packet currently sent.
Consider following case :
An skb is sent, after an idle period of 300 usec.
The air-time (skb->len/pacing_rate) is 500 usec
Instead of setting the pacing timer to now+500 usec,
it will use now+min(500/2, 300) -> now+250usec
This is like having a token bucket with a depth of half
an skb.
Tested:
tc qdisc replace dev eth0 root pfifo_fast
Before
netperf -P0 -H remote -- -q 1000000000 # 8000Mbit
540000 262144 262144 10.00 7710.43
After :
netperf -P0 -H remote -- -q 1000000000 # 8000 Mbit
540000 262144 262144 10.00 7999.75 # Much closer to 8000Mbit target
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_pacing_rate has beed introduced as a u32 field in 2013,
effectively limiting per flow pacing to 34Gbit.
We believe it is time to allow TCP to pace high speed flows
on 64bit hosts, as we now can reach 100Gbit on one TCP flow.
This patch adds no cost for 32bit kernels.
The tcpi_pacing_rate and tcpi_max_pacing_rate were already
exported as 64bit, so iproute2/ss command require no changes.
Unfortunately the SO_MAX_PACING_RATE socket option will stay
32bit and we will need to add a new option to let applications
control high pacing rates.
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 1787144 10.246.9.76:49992 10.246.9.77:36741
timer:(on,003ms,0) ino:91863 sk:2 <->
skmem:(r0,rb540000,t66440,tb2363904,f605944,w1822984,o0,bl0,d0)
ts sack bbr wscale:8,8 rto:201 rtt:0.057/0.006 mss:1448
rcvmss:536 advmss:1448
cwnd:138 ssthresh:178 bytes_acked:256699822585 segs_out:177279177
segs_in:3916318 data_segs_out:177279175
bbr:(bw:31276.8Mbps,mrtt:0,pacing_gain:1.25,cwnd_gain:2)
send 28045.5Mbps lastrcv:73333
pacing_rate 38705.0Mbps delivery_rate 22997.6Mbps
busy:73333ms unacked:135 retrans:0/157 rcv_space:14480
notsent:2085120 minrtt:0.013
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In EDT design, I made the mistake of using tcp_wstamp_ns
to store the last tcp_clock_ns() sample and to store the
pacing virtual timer.
This causes major regressions at high speed flows.
Introduce tcp_clock_cache to store last tcp_clock_ns().
This is needed because some arches have slow high-resolution
kernel time service.
tcp_wstamp_ns is only updated when a packet is sent.
Note that we can remove tcp_mstamp in the future since
tcp_mstamp is essentially tcp_clock_cache/1000, so the
apparent socket size increase is temporary.
Fixes: 9799ccb0e9 ("tcp: add tcp_wstamp_ns socket field")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a generic sk_msg layer, and convert current sockmap and later
kTLS over to make use of it. While sk_buff handles network packet
representation from netdevice up to socket, sk_msg handles data
representation from application to socket layer.
This means that sk_msg framework spans across ULP users in the
kernel, and enables features such as introspection or filtering
of data with the help of BPF programs that operate on this data
structure.
Latter becomes in particular useful for kTLS where data encryption
is deferred into the kernel, and as such enabling the kernel to
perform L7 introspection and policy based on BPF for TLS connections
where the record is being encrypted after BPF has run and came to
a verdict. In order to get there, first step is to transform open
coding of scatter-gather list handling into a common core framework
that subsystems can use.
The code itself has been split and refactored into three bigger
pieces: i) the generic sk_msg API which deals with managing the
scatter gather ring, providing helpers for walking and mangling,
transferring application data from user space into it, and preparing
it for BPF pre/post-processing, ii) the plain sock map itself
where sockets can be attached to or detached from; these bits
are independent of i) which can now be used also without sock
map, and iii) the integration with plain TCP as one protocol
to be used for processing L7 application data (later this could
e.g. also be extended to other protocols like UDP). The semantics
are the same with the old sock map code and therefore no change
of user facing behavior or APIs. While pursuing this work it
also helped finding a number of bugs in the old sockmap code
that we've fixed already in earlier commits. The test_sockmap
kselftest suite passes through fine as well.
Joint work with John.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In order to prepare sockmap logic to be used in combination with kTLS
we need to detangle it from ULP, and further split it in later commits
into a generic API.
Joint work with John.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Whenever the ULP data on the socket is mangled, enforce that the
caller has the socket lock held as otherwise things may race with
initialization and cleanup callbacks from ulp ops as both would
mangle internal socket state.
Joint work with John.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link's carrier goes down it could be a sign of the port changing
networks. If the new network has overlapping addresses with the old one,
then the kernel will continue trying to use neighbor entries established
based on the old network until the entries finally age out - meaning a
potentially long delay with communications not working.
This patch evicts neighbor entries on carrier down with the exception of
those marked permanent. Permanent entries are managed by userspace (either
an admin or a routing daemon such as FRR).
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an MTU update with PMTU smaller than net.ipv4.route.min_pmtu is
received, we must clamp its value. However, we can receive a PMTU
exception with PMTU < old_mtu < ip_rt_min_pmtu, which would lead to an
increase in PMTU.
To fix this, take the smallest of the old MTU and ip_rt_min_pmtu.
Before this patch, in case of an update, the exception's MTU would
always change. Now, an exception can have only its lock flag updated,
but not the MTU, so we need to add a check on locking to the following
"is this exception getting updated, or close to expiring?" test.
Fixes: d52e5a7e7c ("ipv4: lock mtu in fnhe when received PMTU < net.ipv4.route.min_pmtu")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 5aad1de5ea ("ipv4: use separate genid for next hop
exceptions"), exceptions get deprecated separately from cached
routes. In particular, administrative changes don't clear PMTU anymore.
As Stefano described in commit e9fa1495d7 ("ipv6: Reflect MTU changes
on PMTU of exceptions for MTU-less routes"), the PMTU discovered before
the local MTU change can become stale:
- if the local MTU is now lower than the PMTU, that PMTU is now
incorrect
- if the local MTU was the lowest value in the path, and is increased,
we might discover a higher PMTU
Similarly to what commit e9fa1495d7 did for IPv6, update PMTU in those
cases.
If the exception was locked, the discovered PMTU was smaller than the
minimal accepted PMTU. In that case, if the new local MTU is smaller
than the current PMTU, let PMTU discovery figure out if locking of the
exception is still needed.
To do this, we need to know the old link MTU in the NETDEV_CHANGEMTU
notifier. By the time the notifier is called, dev->mtu has been
changed. This patch adds the old MTU as additional information in the
notifier structure, and a new call_netdevice_notifiers_u32() function.
Fixes: 5aad1de5ea ("ipv4: use separate genid for next hop exceptions")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DCTCP has two parts - a new ECN signalling mechanism and the response
function to it. The first part can be used by other congestion
control for DCTCP-ECN deployed networks. This patch moves that part
into a separate tcp_dctcp.h to be used by other congestion control
module (like how Yeah uses Vegas algorithmas). For example, BBR is
experimenting such ECN signal currently
https://tinyurl.com/ietf-102-iccrg-bbr2
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next tree:
1) Support for matching on ipsec policy already set in the route, from
Florian Westphal.
2) Split set destruction into deactivate and destroy phase to make it
fit better into the transaction infrastructure, also from Florian.
This includes a patch to warn on imbalance when setting the new
activate and deactivate interfaces.
3) Release transaction list from the workqueue to remove expensive
synchronize_rcu() from configuration plane path. This speeds up
configuration plane quite a bit. From Florian Westphal.
4) Add new xfrm/ipsec extension, this new extension allows you to match
for ipsec tunnel keys such as source and destination address, spi and
reqid. From Máté Eckl and Florian Westphal.
5) Add secmark support, this includes connsecmark too, patches
from Christian Gottsche.
6) Allow to specify remaining bytes in xt_quota, from Chenbo Feng.
One follow up patch to calm a clang warning for this one, from
Nathan Chancellor.
7) Flush conntrack entries based on layer 3 family, from Kristian Evensen.
8) New revision for cgroups2 to shrink the path field.
9) Get rid of obsolete need_conntrack(), as a result from recent
demodularization works.
10) Use WARN_ON instead of BUG_ON, from Florian Westphal.
11) Unused exported symbol in nf_nat_ipv4_fn(), from Florian.
12) Remove superfluous check for timeout netlink parser and dump
functions in layer 4 conntrack helpers.
13) Unnecessary redundant rcu read side locks in NAT redirect,
from Taehee Yoo.
14) Pass nf_hook_state structure to error handlers, patch from
Florian Westphal.
15) Remove ->new() interface from layer 4 protocol trackers. Place
them in the ->packet() interface. From Florian.
16) Place conntrack ->error() handling in the ->packet() interface.
Patches from Florian Westphal.
17) Remove unused parameter in the pernet initialization path,
also from Florian.
18) Remove additional parameter to specify layer 3 protocol when
looking up for protocol tracker. From Florian.
19) Shrink array of layer 4 protocol trackers, from Florian.
20) Check for linear skb only once from the ALG NAT mangling
codebase, from Taehee Yoo.
21) Use rhashtable_walk_enter() instead of deprecated
rhashtable_walk_init(), also from Taehee.
22) No need to flush all conntracks when only one single address
is gone, from Tan Hu.
23) Remove redundant check for NAT flags in flowtable code, from
Taehee Yoo.
24) Use rhashtable_lookup() instead of rhashtable_lookup_fast()
from netfilter codebase, since rcu read lock side is already
assumed in this path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update inet_netconf_dump_devconf, inet6_netconf_dump_devconf, and
mpls_netconf_dump_devconf for strict data checking. If the flag is set,
the dump request is expected to have an netconfmsg struct as the header.
The struct only has the family member and no attributes can be appended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper to check netlink message for route dumps. If the strict flag
is set the dump request is expected to have an rtmsg struct as the header.
All elements of the struct are expected to be 0 with the exception of
rtm_flags (which is used by both ipv4 and ipv6 dumps) and no attributes
can be appended. rtm_flags can only have RTM_F_CLONED and RTM_F_PREFIX
set.
Update inet_dump_fib, inet6_dump_fib, mpls_dump_routes, ipmr_rtm_dumproute,
and ip6mr_rtm_dumproute to call this helper if strict data checking is
enabled.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update ipmr_rtm_dumplink for strict data checking. If the flag is set,
the dump request is expected to have an ifinfomsg struct as the header.
All elements of the struct are expected to be 0 and no attributes can
be appended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update inet_dump_ifaddr for strict data checking. If the flag is set,
the dump request is expected to have an ifaddrmsg struct as the header
potentially followed by one or more attributes. Any data passed in the
header or as an attribute is taken as a request to influence the data
returned. Only values supported by the dump handler are allowed to be
non-0 or set in the request. At the moment only the IFA_TARGET_NETNSID
attribute is supported. Follow on patches can support for other fields
(e.g., honor ifa_index and only return data for the given device index).
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure extack is passed to nlmsg_parse where easy to do so.
Most of these are dump handlers and leveraging the extack in
the netlink_callback.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2276f58ac5 ("udp: use a separate rx queue for packet reception")
turned static inline __skb_recv_udp() from being a trivial helper around
__skb_recv_datagram() into a UDP specific implementaion, making it
EXPORT_SYMBOL_GPL() at the same time.
There are external modules that got broken by __skb_recv_udp() not being
visible to them. Let's unbreak them by making __skb_recv_udp EXPORT_SYMBOL().
Rationale (one of those) why this is actually "technically correct" thing
to do: __skb_recv_udp() used to be an inline wrapper around
__skb_recv_datagram(), which itself (still, and correctly so, I believe)
is EXPORT_SYMBOL().
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 2276f58ac5 ("udp: use a separate rx queue for packet reception")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the socket lookup cost in udp_gro_receive if no socket has a
udp tunnel callback configured.
udp_sk(sk)->gro_receive requires a registration with
setup_udp_tunnel_sock, which enables the static key.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the refcounting and potential free of dst metrics associated
for ipv4 and ipv6 to a common helper.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4 and ipv6 both use refcounted metrics if FIB entries have metrics set.
Move the common initialization code to a helper and use for both protocols.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the refcounting and potential free of dst metrics associated
with a fib entry to a helper and use it in both ipv4 and ipv6.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate initialization of ipv4 and ipv6 metrics when fib entries
are created into a single helper, ip_fib_metrics_init, that handles
the call to ip_metrics_convert.
If no metrics are defined for the fib entry, then the metrics is set
to dst_default_metrics.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Caching ip_hdr(skb) before a call to pskb_may_pull() is buggy,
do not do it.
Fixes: 2efd4fca70 ("ip: in cmsg IP(V6)_ORIGDSTADDR call pskb_may_pull")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is useful to be able to use the same socket for listening in a
specific VRF, as for sending multicast packets out of a specific
interface. However, the bound device on the socket currently takes
precedence and results in the packets not being sent.
Relax the condition on overriding the output interface to use for
sending packets out of UDP, raw and ping sockets to allow multicast
packets to be sent using the specified multicast interface.
Signed-off-by: Robert Shearman <rshearma@vyatta.att-mail.com>
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzkaller was able to hit the WARN_ON(sock_owned_by_user(sk));
in tcp_close()
While a socket is being closed, it is very possible other
threads find it in rtnetlink dump.
tcp_get_info() will acquire the socket lock for a short amount
of time (slow = lock_sock_fast(sk)/unlock_sock_fast(sk, slow);),
enough to trigger the warning.
Fixes: 67db3e4bfb ("tcp: no longer hold ehash lock while calling tcp_get_info()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(allows for better compiler optimization)
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timer handlers do not imply rcu_read_lock(), so my recent fix
triggered a LOCKDEP warning when SYNACK is retransmit.
Lets add rcu_read_lock()/rcu_read_unlock() pairs around ireq->ireq_opt
usages instead of guessing what is done by callers, since it is
not worth the pain.
Get rid of ireq_opt_deref() helper since it hides the logic
without real benefit, since it is now a standard rcu_dereference().
Fixes: 1ad98e9d1b ("tcp/dccp: fix lockdep issue when SYN is backlogged")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the recent TCP/EDT patch series, I switched TCP and sch_fq
clocks from MONOTONIC to TAI, in order to meet the choice done
earlier for sch_etf packet scheduler.
But sure enough, this broke some setups were the TAI clock
jumps forward (by almost 50 year...), as reported
by Leonard Crestez.
If we want to converge later, we'll probably need to add
an skb field to differentiate the clock bases, or a socket option.
In the meantime, an UDP application will need to use CLOCK_MONOTONIC
base for its SCM_TXTIME timestamps if using fq packet scheduler.
Fixes: 72b0094f91 ("tcp: switch tcp_clock_ns() to CLOCK_TAI base")
Fixes: 142537e419 ("net_sched: sch_fq: switch to CLOCK_TAI")
Fixes: fd2bca2aa7 ("tcp: switch internal pacing timer to CLOCK_TAI")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Tested-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SKBs are coalesced, we can have SKBs with different
frag sizes. Some with PAGE_SIZE and some not with PAGE_SIZE.
Since recv_skip_hint is always set to the full SKB size,
it can overestimate the amount that should be read using
normal read for coalesced packets.
Change the recv_skip_hint so that it only includes the first
frags that are not of PAGE_SIZE.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we have less than PAGE_SIZE of data on receive queue,
we set recv_skip_hint to 0. Instead, set it to the actual
number of bytes available.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2018-10-01
1) Make xfrmi_get_link_net() static to silence a sparse warning.
From Wei Yongjun.
2) Remove a unused esph pointer definition in esp_input().
From Haishuang Yan.
3) Allow the NIC driver to quietly refuse xfrm offload
in case it does not support it, the SA is created
without offload in this case.
From Shannon Nelson.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2018-10-01
1) Validate address prefix lengths in the xfrm selector,
otherwise we may hit undefined behaviour in the
address matching functions if the prefix is too
big for the given address family.
2) Fix skb leak on local message size errors.
From Thadeu Lima de Souza Cascardo.
3) We currently reset the transport header back to the network
header after a transport mode transformation is applied. This
leads to an incorrect transport header when multiple transport
mode transformations are applied. Reset the transport header
only after all transformations are already applied to fix this.
From Sowmini Varadhan.
4) We only support one offloaded xfrm, so reset crypto_done after
the first transformation in xfrm_input(). Otherwise we may call
the wrong input method for subsequent transformations.
From Sowmini Varadhan.
5) Fix NULL pointer dereference when skb_dst_force clears the dst_entry.
skb_dst_force does not really force a dst refcount anymore, it might
clear it instead. xfrm code did not expect this, add a check to not
dereference skb_dst() if it was cleared by skb_dst_force.
6) Validate xfrm template mode, otherwise we can get a stack-out-of-bounds
read in xfrm_state_find. From Sean Tranchetti.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously receiver buffer auto-tuning starts after receiving
one advertised window amount of data. After the initial receiver
buffer was raised by patch a337531b94 ("tcp: up initial rmem to
128KB and SYN rwin to around 64KB"), the reciver buffer may take
too long to start raising. To address this issue, this patch lowers
the initial bytes expected to receive roughly the expected sender's
initial window.
Fixes: a337531b94 ("tcp: up initial rmem to 128KB and SYN rwin to around 64KB")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In normal SYN processing, packets are handled without listener
lock and in RCU protected ingress path.
But syzkaller is known to be able to trick us and SYN
packets might be processed in process context, after being
queued into socket backlog.
In commit 06f877d613 ("tcp/dccp: fix other lockdep splats
accessing ireq_opt") I made a very stupid fix, that happened
to work mostly because of the regular path being RCU protected.
Really the thing protecting ireq->ireq_opt is RCU read lock,
and the pseudo request refcnt is not relevant.
This patch extends what I did in commit 449809a66c ("tcp/dccp:
block BH for SYN processing") by adding an extra rcu_read_{lock|unlock}
pair in the paths that might be taken when processing SYN from
socket backlog (thus possibly in process context)
Fixes: 06f877d613 ("tcp/dccp: fix other lockdep splats accessing ireq_opt")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously TCP initial receive buffer is ~87KB by default and
the initial receive window is ~29KB (20 MSS). This patch changes
the two numbers to 128KB and ~64KB (rounding down to the multiples
of MSS) respectively. The patch also simplifies the calculations s.t.
the two numbers are directly controlled by sysctl tcp_rmem[1]:
1) Initial receiver buffer budget (sk_rcvbuf): while this should
be configured via sysctl tcp_rmem[1], previously tcp_fixup_rcvbuf()
always override and set a larger size when a new connection
establishes.
2) Initial receive window in SYN: previously it is set to 20
packets if MSS <= 1460. The number 20 was based on the initial
congestion window of 10: the receiver needs twice amount to
avoid being limited by the receive window upon out-of-order
delivery in the first window burst. But since this only
applies if the receiving MSS <= 1460, connection using large MTU
(e.g. to utilize receiver zero-copy) may be limited by the
receive window.
With this patch TCP memory configuration is more straight-forward and
more properly sized to modern high-speed networks by default. Several
popular stacks have been announcing 64KB rwin in SYNs as well.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We configured iptables as below, which only allowed incoming data on
established connections:
iptables -t mangle -A PREROUTING -m state --state ESTABLISHED -j ACCEPT
iptables -t mangle -P PREROUTING DROP
When deleting a secondary address, current masquerade implements would
flush all conntracks on this device. All the established connections on
primary address also be deleted, then subsequent incoming data on the
connections would be dropped wrongly because it was identified as NEW
connection.
So when an address was delete, it should only flush connections related
with the address.
Signed-off-by: Tan Hu <tan.hu@zte.com.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
(the parameters in question are mark and flow_flags)
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(the parameters in question are mark and flow_flags)
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong noted that we need the same checks introduced by commit 76c0ddd8c3
("ip6_tunnel: be careful when accessing the inner header")
even for ipv4 tunnels.
Fixes: c544193214 ("GRE: Refactor GRE tunneling code.")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ip[6]frag_high_thresh sysctl values in new namespaces are
hard-limited to those of the root/init ns.
There are at least two use cases when it would be desirable to
set the high_thresh values higher in a child namespace vs the global hard
limit:
- a security/ddos protection policy may lower the thresholds in the
root/init ns but allow for a special exception in a child namespace
- testing: a test running in a namespace may want to set these
thresholds higher in its namespace than what is in the root/init ns
The new behavior:
# ip netns add testns
# ip netns exec testns bash
# sysctl -w net.ipv4.ipfrag_high_thresh=9000000
net.ipv4.ipfrag_high_thresh = 9000000
# sysctl net.ipv4.ipfrag_high_thresh
net.ipv4.ipfrag_high_thresh = 9000000
# sysctl -w net.ipv6.ip6frag_high_thresh=9000000
net.ipv6.ip6frag_high_thresh = 9000000
# sysctl net.ipv6.ip6frag_high_thresh
net.ipv6.ip6frag_high_thresh = 9000000
The old behavior:
# ip netns add testns
# ip netns exec testns bash
# sysctl -w net.ipv4.ipfrag_high_thresh=9000000
net.ipv4.ipfrag_high_thresh = 9000000
# sysctl net.ipv4.ipfrag_high_thresh
net.ipv4.ipfrag_high_thresh = 4194304
# sysctl -w net.ipv6.ip6frag_high_thresh=9000000
net.ipv6.ip6frag_high_thresh = 9000000
# sysctl net.ipv6.ip6frag_high_thresh
net.ipv6.ip6frag_high_thresh = 4194304
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv4/fib_frontend.c: In function 'fib_info_nh_uses_dev':
net/ipv4/fib_frontend.c:322:6: error: unused variable 'ret' [-Werror=unused-variable]
cc1: all warnings being treated as errors
Fixes: 78f2756c5f ("net/ipv4: Move device validation to helper")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Ahern <dsahern@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now TCP keeps track of tcp_wstamp_ns, recording the earliest
departure time of next packet, we can remove duplicate code
from tcp_internal_pacing()
This removes one ktime_get_tai_ns() call, and a divide.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP keeps track of tcp_wstamp_ns by itself, meaning sch_fq
no longer has to do it.
Thanks to this model, TCP can get more accurate RTT samples,
since pacing no longer inflates them.
This has the nice effect of removing some delays caused by FQ
quantum mechanism, causing inflated max/P99 latencies.
Also we might relax TCP Small Queue tight limits in the future,
since this new model allow TCP to build bigger batches, since
sch_fq (or a device with earliest departure time offload) ensure
these packets will be delivered on time.
Note that other protocols are not converted (they will probably
never be) so sch_fq has still support for SO_MAX_PACING_RATE
Tested:
Test showing FQ pacing quantum artifact for low-rate flows,
adding unexpected throttles for RPC flows, inflating max and P99 latencies.
The parameters chosen here are to show what happens typically when
a TCP flow has a reduced pacing rate (this can be caused by a reduced
cwin after few losses, or/and rtt above few ms)
MIBS="MIN_LATENCY,MEAN_LATENCY,MAX_LATENCY,P99_LATENCY,STDDEV_LATENCY"
Before :
$ netperf -H 10.246.7.133 -t TCP_RR -Cc -T6,6 -- -q 2000000 -r 100,100 -o $MIBS
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.246.7.133 () port 0 AF_INET : first burst 0 : cpu bind
Minimum Latency Microseconds,Mean Latency Microseconds,Maximum Latency Microseconds,99th Percentile Latency Microseconds,Stddev Latency Microseconds
19,82.78,5279,3825,482.02
After :
$ netperf -H 10.246.7.133 -t TCP_RR -Cc -T6,6 -- -q 2000000 -r 100,100 -o $MIBS
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.246.7.133 () port 0 AF_INET : first burst 0 : cpu bind
Minimum Latency Microseconds,Mean Latency Microseconds,Maximum Latency Microseconds,99th Percentile Latency Microseconds,Stddev Latency Microseconds
20,49.94,128,63,3.18
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Next patch will use tcp_wstamp_ns to feed internal
TCP pacing timer, so switch to CLOCK_TAI to share same base.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch internal TCP skb->skb_mstamp to skb->skb_mstamp_ns,
from usec units to nsec units.
Do not clear skb->tstamp before entering IP stacks in TX,
so that qdisc or devices can implement pacing based on the
earliest departure time instead of socket sk->sk_pacing_rate
Packets are fed with tcp_wstamp_ns, and following patch
will update tcp_wstamp_ns when both TCP and sch_fq switch to
the earliest departure time mechanism.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP will soon provide earliest departure time on TX skbs.
It needs to track this in a new variable.
tcp_mstamp_refresh() needs to update this variable, and
became too big to stay an inline.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where TCP reads skb->skb_mstamp expecting
a value in usec unit.
skb->tstamp (aka skb->skb_mstamp) will soon store CLOCK_TAI nsec value.
Add tcp_skb_timestamp_us() to provide proper conversion when needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kfree_skb has taken the null pointer into account. hence it is safe
to remove the redundant null pointer check before kfree_skb.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert nft_fib4_eval to the new device checking helper and
remove the duplicate code.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert rpfilter_lookup_reverse to the new device checking helper
and remove the duplicate code.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the device matching check in __fib_validate_source to a helper and
export it for use by netfilter modules. Code move only; no functional
change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new tls tests added in parallel in both net and net-next.
Used Stephen Rothwell's linux-next resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 40413955ee ("Cipso: cipso_v4_optptr enter infinite loop") fixed
a possible infinite loop in the IP option parsing of CIPSO. The fix
assumes that ip_options_compile filtered out all zero length options and
that no other one-byte options beside IPOPT_END and IPOPT_NOOP exist.
While this assumption currently holds true, add explicit checks for zero
length and invalid length options to be safe for the future. Even though
ip_options_compile should have validated the options, the introduction of
new one-byte options can still confuse this code without the additional
checks.
Signed-off-by: Stefan Nuernberger <snu@amazon.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Simon Veith <sveith@amazon.de>
Cc: stable@vger.kernel.org
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no external callers anymore, previous change just
forgot to also remove the EXPORT_SYMBOL().
Fixes: 9971a514ed ("netfilter: nf_nat: add nat type hooks to nat core")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
gre_parse_header stops parsing when csum_err is encountered, which means
tpi->key is undefined and ip_tunnel_lookup will return NULL improperly.
This patch introduce a NULL pointer as csum_err parameter. Even when
csum_err is encountered, it won't return error and continue parsing gre
header as expected.
Fixes: 9f57c67c37 ("gre: Remove support for sharing GRE protocol hook.")
Reported-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2abb7cdc0d ("udp: Add support for doing checksum
unnecessary conversion") left out the early demux path for
connected sockets. As a result IP_CMSG_CHECKSUM gives wrong
values for such socket when GRO is not enabled/available.
This change addresses the issue by moving the csum conversion to a
common helper and using such helper in both the default and the
early demux rx path.
Fixes: 2abb7cdc0d ("udp: Add support for doing checksum unnecessary conversion")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When splitting a GSO segment that consists of encapsulated packets, the
skb->mac_len of the segments can end up being set wrong, causing packet
drops in particular when using act_mirred and ifb interfaces in
combination with a qdisc that splits GSO packets.
This happens because at the time skb_segment() is called, network_header
will point to the inner header, throwing off the calculation in
skb_reset_mac_len(). The network_header is subsequently adjust by the
outer IP gso_segment handlers, but they don't set the mac_len.
Fix this by adding skb_reset_mac_len() calls to both the IPv4 and IPv6
gso_segment handlers, after they modify the network_header.
Many thanks to Eric Dumazet for his help in identifying the cause of
the bug.
Acked-by: Dave Taht <dave.taht@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When splitting a GSO segment that consists of encapsulated packets, the
skb->mac_len of the segments can end up being set wrong, causing packet
drops in particular when using act_mirred and ifb interfaces in
combination with a qdisc that splits GSO packets.
This happens because at the time skb_segment() is called, network_header
will point to the inner header, throwing off the calculation in
skb_reset_mac_len(). The network_header is subsequently adjust by the
outer IP gso_segment handlers, but they don't set the mac_len.
Fix this by adding skb_reset_mac_len() calls to both the IPv4 and IPv6
gso_segment handlers, after they modify the network_header.
Many thanks to Eric Dumazet for his help in identifying the cause of
the bug.
Acked-by: Dave Taht <dave.taht@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing icmp unreachable message for erspan tunnel, tunnel id
should be erspan_net_id instead of ipgre_net_id.
Fixes: 84e54fe0a5 ("gre: introduce native tunnel support for ERSPAN")
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If erspan tunnel hasn't been established, we'd better send icmp port
unreachable message after receive erspan packets.
Fixes: 84e54fe0a5 ("gre: introduce native tunnel support for ERSPAN")
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert pr_info to net_info_ratelimited to limit the total number of
synflood warnings.
Commit 946cedccbd ("tcp: Change possible SYN flooding messages")
rate limits synflood warnings to one per listener.
Workloads that open many listener sockets can still see a high rate of
log messages. Syzkaller is one frequent example.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for you net tree:
1) Remove duplicated include at the end of UDP conntrack, from Yue Haibing.
2) Restore conntrack dependency on xt_cluster, from Martin Willi.
3) Fix splat with GSO skbs from the checksum target, from Florian Westphal.
4) Rework ct timeout support, the template strategy to attach custom timeouts
is not correct since it will not work in conjunction with conntrack zones
and we have a possible free after use when removing the rule due to missing
refcounting. To fix these problems, do not use conntrack template at all
and set custom timeout on the already valid conntrack object. This
fix comes with a preparation patch to simplify timeout adjustment by
initializating the first position of the timeout array for all of the
existing trackers. Patchset from Florian Westphal.
5) Fix missing dependency on from IPv4 chain NAT type, from Florian.
6) Release chain reference counter from the flush path, from Taehee Yoo.
7) After flushing an iptables ruleset, conntrack hooks are unregistered
and entries are left stale to be cleaned up by the timeout garbage
collector. No TCP tracking is done on established flows by this time.
If ruleset is reloaded, then hooks are registered again and TCP
tracking is restored, which considers packets to be invalid. Clear
window tracking to exercise TCP flow pickup from the middle given that
history is lost for us. Again from Florian.
8) Fix crash from netlink interface with CONFIG_NF_CONNTRACK_TIMEOUT=y
and CONFIG_NF_CT_NETLINK_TIMEOUT=n.
9) Broken CT target due to returning incorrect type from
ctnl_timeout_find_get().
10) Solve conntrack clash on NF_REPEAT verdicts too, from Michal Vaner.
11) Missing conversion of hashlimit sysctl interface to new API, from
Cong Wang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It documents what is happening, and eliminates the spurious list
pointer poisoning.
In the long term, in order to get proper list head debugging, we
might want to use the list poison value as the indicator that
an SKB is a singleton and not on a list.
Signed-off-by: David S. Miller <davem@davemloft.net>
An SKB is not on a list if skb->next is NULL.
Codify this convention into a helper function and use it
where we are dequeueing an SKB and need to mark it as such.
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the documentation in msg_zerocopy.rst, the SO_ZEROCOPY
flag was introduced because send(2) ignores unknown message flags and
any legacy application which was accidentally passing the equivalent of
MSG_ZEROCOPY earlier should not see any new behaviour.
Before commit f214f915e7 ("tcp: enable MSG_ZEROCOPY"), a send(2) call
which passed the equivalent of MSG_ZEROCOPY without setting SO_ZEROCOPY
would succeed. However, after that commit, it fails with -ENOBUFS. So
it appears that the SO_ZEROCOPY flag fails to fulfill its intended
purpose. Fix it.
Fixes: f214f915e7 ("tcp: enable MSG_ZEROCOPY")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_fill_ifaddr() already took 6 arguments which meant the 7th argument
would need to be pushed onto the stack on x86.
Add a new struct inet_fill_args which holds common information passed
to inet_fill_ifaddr() and shortens the function to three pointer arguments.
Signed-off-by: Christian Brauner <christian@brauner.io>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Backwards Compatibility:
If userspace wants to determine whether ipv4 RTM_GETADDR requests
support the new IFA_TARGET_NETNSID property it should verify that the
reply includes the IFA_TARGET_NETNSID property. If it does not
userspace should assume that IFA_TARGET_NETNSID is not supported for
ipv4 RTM_GETADDR requests on this kernel.
- From what I gather from current userspace tools that make use of
RTM_GETADDR requests some of them pass down struct ifinfomsg when they
should actually pass down struct ifaddrmsg. To not break existing
tools that pass down the wrong struct we will do the same as for
RTM_GETLINK | NLM_F_DUMP requests and not error out when the
nlmsg_parse() fails.
- Security:
Callers must have CAP_NET_ADMIN in the owning user namespace of the
target network namespace.
Signed-off-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
A policy may have been set up with multiple transforms (e.g., ESP
and ipcomp). In this situation, the ingress IPsec processing
iterates in xfrm_input() and applies each transform in turn,
processing the nexthdr to find any additional xfrm that may apply.
This patch resets the transport header back to network header
only after the last transformation so that subsequent xfrms
can find the correct transport header.
Fixes: 7785bba299 ("esp: Add a software GRO codepath")
Suggested-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
cp_hashinfo.ehash_mask is always an odd number, which is set in function
alloc_large_system_hash(). See bellow,
if (_hash_mask)
*_hash_mask = (1 << log2qty) - 1; <<< always odd number
Hence the local variable 'cnt' is a even number, as a result of that it is
no difference to do the incrementation here.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After link down and up, i.e. when call ip_mc_up(), we doesn't init
im->unsolicit_count. So after igmp_timer_expire(), we will not start
timer again and only send one unsolicit report at last.
Fix it by initializing im->unsolicit_count in igmp_group_added(), so
we can respect igmp robustness value.
Fixes: 24803f38a5 ("igmp: do not remove igmp souce list info when set link down")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not start timer if im->unsolicit_count equal to 0 after decrease.
Or we will send one more unsolicit report message. i.e. 3 instead of 2 by
default.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 1337 says:
''Ignore RST segments in TIME-WAIT state.
If the 2 minute MSL is enforced, this fix avoids all three hazards.''
So with net.ipv4.tcp_rfc1337=1, expected behaviour is to have TIME-WAIT sk
expire rather than removing it instantly when a reset is received.
However, Linux will also re-start the TIME-WAIT timer.
This causes connect to fail when tying to re-use ports or very long
delays (until syn retry interval exceeds MSL).
packetdrill test case:
// Demonstrate bogus rearming of TIME-WAIT timer in rfc1337 mode.
`sysctl net.ipv4.tcp_rfc1337=1`
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
0.000 bind(3, ..., ...) = 0
0.000 listen(3, 1) = 0
0.100 < S 0:0(0) win 29200 <mss 1460,nop,nop,sackOK,nop,wscale 7>
0.100 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 7>
0.200 < . 1:1(0) ack 1 win 257
0.200 accept(3, ..., ...) = 4
// Receive first segment
0.310 < P. 1:1001(1000) ack 1 win 46
// Send one ACK
0.310 > . 1:1(0) ack 1001
// read 1000 byte
0.310 read(4, ..., 1000) = 1000
// Application writes 100 bytes
0.350 write(4, ..., 100) = 100
0.350 > P. 1:101(100) ack 1001
// ACK
0.500 < . 1001:1001(0) ack 101 win 257
// close the connection
0.600 close(4) = 0
0.600 > F. 101:101(0) ack 1001 win 244
// Our side is in FIN_WAIT_1 & waits for ack to fin
0.7 < . 1001:1001(0) ack 102 win 244
// Our side is in FIN_WAIT_2 with no outstanding data.
0.8 < F. 1001:1001(0) ack 102 win 244
0.8 > . 102:102(0) ack 1002 win 244
// Our side is now in TIME_WAIT state, send ack for fin.
0.9 < F. 1002:1002(0) ack 102 win 244
0.9 > . 102:102(0) ack 1002 win 244
// Peer reopens with in-window SYN:
1.000 < S 1000:1000(0) win 9200 <mss 1460,nop,nop,sackOK,nop,wscale 7>
// Therefore, reply with ACK.
1.000 > . 102:102(0) ack 1002 win 244
// Peer sends RST for this ACK. Normally this RST results
// in tw socket removal, but rfc1337=1 setting prevents this.
1.100 < R 1002:1002(0) win 244
// second syn. Due to rfc1337=1 expect another pure ACK.
31.0 < S 1000:1000(0) win 9200 <mss 1460,nop,nop,sackOK,nop,wscale 7>
31.0 > . 102:102(0) ack 1002 win 244
// .. and another RST from peer.
31.1 < R 1002:1002(0) win 244
31.2 `echo no timer restart;ss -m -e -a -i -n -t -o state TIME-WAIT`
// third syn after one minute. Time-Wait socket should have expired by now.
63.0 < S 1000:1000(0) win 9200 <mss 1460,nop,nop,sackOK,nop,wscale 7>
// so we expect a syn-ack & 3whs to proceed from here on.
63.0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 7>
Without this patch, 'ss' shows restarts of tw timer and last packet is
thus just another pure ack, more than one minute later.
This restores the original code from commit 283fd6cf0be690a83
("Merge in ANK networking jumbo patch") in netdev-vger-cvs.git .
For some reason the else branch was removed/lost in 1f28b683339f7
("Merge in TCP/UDP optimizations and [..]") and timer restart became
unconditional.
Reported-by: Michal Tesar <mtesar@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make IPv4 consistent with IPv6 and return an extack message that the
ONLINK flag requires a nexthop device.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently a Linux IPv6 TCP sender will change the flow label upon
timeouts to potentially steer away from a data path that has gone
bad. However this does not help if the problem is on the ACK path
and the data path is healthy. In this case the receiver is likely
to receive repeated spurious retransmission because the sender
couldn't get the ACKs in time and has recurring timeouts.
This patch adds another feature to mitigate this problem. It
leverages the DSACK states in the receiver to change the flow
label of the ACKs to speculatively re-route the ACK packets.
In order to allow triggering on the second consecutive spurious
RTO, the receiver changes the flow label upon sending a second
consecutive DSACK for a sequence number below RCV.NXT.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NF_TABLES_IPV4 is now boolean so it is possible to set
NF_TABLES=m
NF_TABLES_IPV4=y
NFT_CHAIN_NAT_IPV4=y
which causes:
nft_chain_nat_ipv4.c:(.text+0x6d): undefined reference to `nft_do_chain'
Wrap NFT_CHAIN_NAT_IPV4 and related nat expressions with NF_TABLES to
restore the dependency.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 02c7b25e5f ("netfilter: nf_tables: build-in filter chain type")
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The current behavior of IP defragmentation is inconsistent:
- some overlapping/wrong length fragments are dropped without
affecting the queue;
- most overlapping fragments cause the whole frag queue to be dropped.
This patch brings consistency: if a bad fragment is detected,
the whole frag queue is dropped. Two major benefits:
- fail fast: corrupted frag queues are cleared immediately, instead of
by timeout;
- testing of overlapping fragments is now much easier: any kind of
random fragment length mutation now leads to the frag queue being
discarded (IP packet dropped); before this patch, some overlaps were
"corrected", with tests not seeing expected packet drops.
Note that in one case (see "if (end&7)" conditional) the current
behavior is preserved as there are concerns that this could be
legitimate padding.
Signed-off-by: Peter Oskolkov <posk@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer 'esph' is defined but is never used hence it is redundant
and canbe removed.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
After erspan_ver is introudced, if erspan_ver is not set in iproute, its
value will be left 0 by default. Since Commit 02f99df187 ("erspan: fix
invalid erspan version."), it has broken the traffic due to the version
check in erspan_xmit if users are not aware of 'erspan_ver' param, like
using an old version of iproute.
To fix this compatibility problem, it sets erspan_ver to 1 by default
when adding an erspan dev in erspan_setup. Note that we can't do it in
ipgre_netlink_parms, as this function is also used by ipgre_changelink.
Fixes: 02f99df187 ("erspan: fix invalid erspan version.")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes a corner case where TCP BBR would enter PROBE_RTT
mode but not reduce its cwnd. If a TCP receiver ACKed less than one
full segment, the number of delivered/acked packets was 0, so that
bbr_set_cwnd() would short-circuit and exit early, without cutting
cwnd to the value we want for PROBE_RTT.
The fix is to instead make sure that even when 0 full packets are
ACKed, we do apply all the appropriate caps, including the cap that
applies in PROBE_RTT mode.
Fixes: 0f8782ea14 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Kevin Yang <yyd@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the case where BBR does not exit PROBE_RTT mode when
it restarts from idle. When BBR restarts from idle and if BBR is in
PROBE_RTT mode, BBR should check if it's time to exit PROBE_RTT. If
yes, then BBR should exit PROBE_RTT mode and restore the cwnd to its
full value.
Fixes: 0f8782ea14 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Kevin Yang <yyd@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add a helper function bbr_check_probe_rtt_done() to
1. check the condition to see if bbr should exit probe_rtt mode;
2. process the logic of exiting probe_rtt mode.
Fixes: 0f8782ea14 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Kevin Yang <yyd@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp uses per-cpu (and per namespace) sockets (net->ipv4.tcp_sk) internally
to send some control packets.
1) RST packets, through tcp_v4_send_reset()
2) ACK packets in SYN-RECV and TIME-WAIT state, through tcp_v4_send_ack()
These packets assert IP_DF, and also use the hashed IP ident generator
to provide an IPv4 ID number.
Geoff Alexander reported this could be used to build off-path attacks.
These packets should not be fragmented, since their size is smaller than
IPV4_MIN_MTU. Only some tunneled paths could eventually have to fragment,
regardless of inner IPID.
We really can use zero IPID, to address the flaw, and as a bonus,
avoid a couple of atomic operations in ip_idents_reserve()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Geoff Alexander <alexandg@cs.unm.edu>
Tested-by: Geoff Alexander <alexandg@cs.unm.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
I found that in BPF sockmap programs once we either delete a socket
from the map or we updated a map slot and the old socket was purged
from the map that these socket can never get reattached into a map
even though their related psock has been dropped entirely at that
point.
Reason is that tcp_cleanup_ulp() leaves the old icsk->icsk_ulp_ops
intact, so that on the next tcp_set_ulp_id() the kernel returns an
-EEXIST thinking there is still some active ULP attached.
BPF sockmap is the only one that has this issue as the other user,
kTLS, only calls tcp_cleanup_ulp() from tcp_v4_destroy_sock() whereas
sockmap semantics allow dropping the socket from the map with all
related psock state being cleaned up.
Fixes: 1aa12bdf1b ("bpf: sockmap, add sock close() hook to remove socks")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Lets not turn the TCP ULP lookup into an arbitrary module loader as
we only intend to load ULP modules through this mechanism, not other
unrelated kernel modules:
[root@bar]# cat foo.c
#include <sys/types.h>
#include <sys/socket.h>
#include <linux/tcp.h>
#include <linux/in.h>
int main(void)
{
int sock = socket(PF_INET, SOCK_STREAM, 0);
setsockopt(sock, IPPROTO_TCP, TCP_ULP, "sctp", sizeof("sctp"));
return 0;
}
[root@bar]# gcc foo.c -O2 -Wall
[root@bar]# lsmod | grep sctp
[root@bar]# ./a.out
[root@bar]# lsmod | grep sctp
sctp 1077248 4
libcrc32c 16384 3 nf_conntrack,nf_nat,sctp
[root@bar]#
Fix it by adding module alias to TCP ULP modules, so probing module
via request_module() will be limited to tcp-ulp-[name]. The existing
modules like kTLS will load fine given tcp-ulp-tls alias, but others
will fail to load:
[root@bar]# lsmod | grep sctp
[root@bar]# ./a.out
[root@bar]# lsmod | grep sctp
[root@bar]#
Sockmap is not affected from this since it's either built-in or not.
Fixes: 734942cc4e ("tcp: ULP infrastructure")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-08-13
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add driver XDP support for veth. This can be used in conjunction with
redirect of another XDP program e.g. sitting on NIC so the xdp_frame
can be forwarded to the peer veth directly without modification,
from Toshiaki.
2) Add a new BPF map type REUSEPORT_SOCKARRAY and prog type SK_REUSEPORT
in order to provide more control and visibility on where a SO_REUSEPORT
sk should be located, and the latter enables to directly select a sk
from the bpf map. This also enables map-in-map for application migration
use cases, from Martin.
3) Add a new BPF helper bpf_skb_ancestor_cgroup_id() that returns the id
of cgroup v2 that is the ancestor of the cgroup associated with the
skb at the ancestor_level, from Andrey.
4) Implement BPF fs map pretty-print support based on BTF data for regular
hash table and LRU map, from Yonghong.
5) Decouple the ability to attach BTF for a map from the key and value
pretty-printer in BPF fs, and enable further support of BTF for maps for
percpu and LPM trie, from Daniel.
6) Implement a better BPF sample of using XDP's CPU redirect feature for
load balancing SKB processing to remote CPU. The sample implements the
same XDP load balancing as Suricata does which is symmetric hash based
on IP and L4 protocol, from Jesper.
7) Revert adding NULL pointer check with WARN_ON_ONCE() in __xdp_return()'s
critical path as it is ensured that the allocator is present, from Björn.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the runtime behavior of IP defrag queue:
incoming in-order fragments are added to the end of the current
list/"run" of in-order fragments at the tail.
On some workloads, UDP stream performance is substantially improved:
RX: ./udp_stream -F 10 -T 2 -l 60
TX: ./udp_stream -c -H <host> -F 10 -T 5 -l 60
with this patchset applied on a 10Gbps receiver:
throughput=9524.18
throughput_units=Mbit/s
upstream (net-next):
throughput=4608.93
throughput_units=Mbit/s
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces several helper functions/macros that will be
used in the follow-up patch. No runtime changes yet.
The new logic (fully implemented in the second patch) is as follows:
* Nodes in the rb-tree will now contain not single fragments, but lists
of consecutive fragments ("runs").
* At each point in time, the current "active" run at the tail is
maintained/tracked. Fragments that arrive in-order, adjacent
to the previous tail fragment, are added to this tail run without
triggering the re-balancing of the rb-tree.
* If a fragment arrives out of order with the offset _before_ the tail run,
it is inserted into the rb-tree as a single fragment.
* If a fragment arrives after the current tail fragment (with a gap),
it starts a new "tail" run, as is inserted into the rb-tree
at the end as the head of the new run.
skb->cb is used to store additional information
needed here (suggested by Eric Dumazet).
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 5681 sec 4.2:
To provide feedback to senders recovering from losses, the receiver
SHOULD send an immediate ACK when it receives a data segment that
fills in all or part of a gap in the sequence space.
When a gap is partially filled, __tcp_ack_snd_check already checks
the out-of-order queue and correctly send an immediate ACK. However
when a gap is fully filled, the previous implementation only resets
pingpong mode which does not guarantee an immediate ACK because the
quick ACK counter may be zero. This patch addresses this issue by
marking the one-time immediate ACK flag instead.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent fix of acking immediately in DCTCP on CE status change
has an undesirable side-effect: it also resets TCP ack timer and
disables pingpong mode (interactive session). But the CE status
change has nothing to do with them. This patch addresses that by
using the new one-time immediate ACK flag instead of calling
tcp_enter_quickack_mode().
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new flag to indicate a one-time immediate ACK. This flag is
occasionaly set under specific TCP protocol states in addition to
the more common quickack mechanism for interactive application.
In several cases in the TCP code we want to force an immediate ACK
but do not want to call tcp_enter_quickack_mode() because we do
not want to forget the icsk_ack.pingpong or icsk_ack.ato state.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows a BPF_PROG_TYPE_SK_REUSEPORT bpf prog to select a
SO_REUSEPORT sk from a BPF_MAP_TYPE_REUSEPORT_ARRAY introduced in
the earlier patch. "bpf_run_sk_reuseport()" will return -ECONNREFUSED
when the BPF_PROG_TYPE_SK_REUSEPORT prog returns SK_DROP.
The callers, in inet[6]_hashtable.c and ipv[46]/udp.c, are modified to
handle this case and return NULL immediately instead of continuing the
sk search from its hashtable.
It re-uses the existing SO_ATTACH_REUSEPORT_EBPF setsockopt to attach
BPF_PROG_TYPE_SK_REUSEPORT. The "sk_reuseport_attach_bpf()" will check
if the attaching bpf prog is in the new SK_REUSEPORT or the existing
SOCKET_FILTER type and then check different things accordingly.
One level of "__reuseport_attach_prog()" call is removed. The
"sk_unhashed() && ..." and "sk->sk_reuseport_cb" tests are pushed
back to "reuseport_attach_prog()" in sock_reuseport.c. sock_reuseport.c
seems to have more knowledge on those test requirements than filter.c.
In "reuseport_attach_prog()", after new_prog is attached to reuse->prog,
the old_prog (if any) is also directly freed instead of returning the
old_prog to the caller and asking the caller to free.
The sysctl_optmem_max check is moved back to the
"sk_reuseport_attach_filter()" and "sk_reuseport_attach_bpf()".
As of other bpf prog types, the new BPF_PROG_TYPE_SK_REUSEPORT is only
bounded by the usual "bpf_prog_charge_memlock()" during load time
instead of bounded by both bpf_prog_charge_memlock and sysctl_optmem_max.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch adds a BPF_PROG_TYPE_SK_REUSEPORT which can select
a SO_REUSEPORT sk from a BPF_MAP_TYPE_REUSEPORT_ARRAY. Like other
non SK_FILTER/CGROUP_SKB program, it requires CAP_SYS_ADMIN.
BPF_PROG_TYPE_SK_REUSEPORT introduces "struct sk_reuseport_kern"
to store the bpf context instead of using the skb->cb[48].
At the SO_REUSEPORT sk lookup time, it is in the middle of transiting
from a lower layer (ipv4/ipv6) to a upper layer (udp/tcp). At this
point, it is not always clear where the bpf context can be appended
in the skb->cb[48] to avoid saving-and-restoring cb[]. Even putting
aside the difference between ipv4-vs-ipv6 and udp-vs-tcp. It is not
clear if the lower layer is only ipv4 and ipv6 in the future and
will it not touch the cb[] again before transiting to the upper
layer.
For example, in udp_gro_receive(), it uses the 48 byte NAPI_GRO_CB
instead of IP[6]CB and it may still modify the cb[] after calling
the udp[46]_lib_lookup_skb(). Because of the above reason, if
sk->cb is used for the bpf ctx, saving-and-restoring is needed
and likely the whole 48 bytes cb[] has to be saved and restored.
Instead of saving, setting and restoring the cb[], this patch opts
to create a new "struct sk_reuseport_kern" and setting the needed
values in there.
The new BPF_PROG_TYPE_SK_REUSEPORT and "struct sk_reuseport_(kern|md)"
will serve all ipv4/ipv6 + udp/tcp combinations. There is no protocol
specific usage at this point and it is also inline with the current
sock_reuseport.c implementation (i.e. no protocol specific requirement).
In "struct sk_reuseport_md", this patch exposes data/data_end/len
with semantic similar to other existing usages. Together
with "bpf_skb_load_bytes()" and "bpf_skb_load_bytes_relative()",
the bpf prog can peek anywhere in the skb. The "bind_inany" tells
the bpf prog that the reuseport group is bind-ed to a local
INANY address which cannot be learned from skb.
The new "bind_inany" is added to "struct sock_reuseport" which will be
used when running the new "BPF_PROG_TYPE_SK_REUSEPORT" bpf prog in order
to avoid repeating the "bind INANY" test on
"sk_v6_rcv_saddr/sk->sk_rcv_saddr" every time a bpf prog is run. It can
only be properly initialized when a "sk->sk_reuseport" enabled sk is
adding to a hashtable (i.e. during "reuseport_alloc()" and
"reuseport_add_sock()").
The new "sk_select_reuseport()" is the main helper that the
bpf prog will use to select a SO_REUSEPORT sk. It is the only function
that can use the new BPF_MAP_TYPE_REUSEPORT_ARRAY. As mentioned in
the earlier patch, the validity of a selected sk is checked in
run time in "sk_select_reuseport()". Doing the check in
verification time is difficult and inflexible (consider the map-in-map
use case). The runtime check is to compare the selected sk's reuseport_id
with the reuseport_id that we want. This helper will return -EXXX if the
selected sk cannot serve the incoming request (e.g. reuseport_id
not match). The bpf prog can decide if it wants to do SK_DROP as its
discretion.
When the bpf prog returns SK_PASS, the kernel will check if a
valid sk has been selected (i.e. "reuse_kern->selected_sk != NULL").
If it does , it will use the selected sk. If not, the kernel
will select one from "reuse->socks[]" (as before this patch).
The SK_DROP and SK_PASS handling logic will be in the next patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
We accidentally removed the parentheses here, but they are required
because '!' has higher precedence than '&'.
Fixes: fa0f527358 ("ip: use rb trees for IP frag queue.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to TCP OOO RX queue, it makes sense to use rb trees to store
IP fragments, so that OOO fragments are inserted faster.
Tested:
- a follow-up patch contains a rather comprehensive ip defrag
self-test (functional)
- ran neper `udp_stream -c -H <host> -F 100 -l 300 -T 20`:
netstat --statistics
Ip:
282078937 total packets received
0 forwarded
0 incoming packets discarded
946760 incoming packets delivered
18743456 requests sent out
101 fragments dropped after timeout
282077129 reassemblies required
944952 packets reassembled ok
262734239 packet reassembles failed
(The numbers/stats above are somewhat better re:
reassemblies vs a kernel without this patchset. More
comprehensive performance testing TBD).
Reported-by: Jann Horn <jannh@google.com>
Reported-by: Juha-Matti Tilli <juha-matti.tilli@iki.fi>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This behavior is required in IPv6, and there is little need
to tolerate overlapping fragments in IPv4. This change
simplifies the code and eliminates potential DDoS attack vectors.
Tested: ran ip_defrag selftest (not yet available uptream).
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
variable 'err' is unmodified after initalization,
so simply cleans up it and returns 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit ffc2b6ee41 ("ip_gre: fix IFLA_MTU ignored on NEWLINK")
variable t_hlen is assigned values that are never read,
hence they are redundant and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
net/ipv4/tcp_output.c: In function 'tcp_collapse_retrans':
net/ipv4/tcp_output.c:2700:6: warning:
variable 'skb_size' set but not used [-Wunused-but-set-variable]
int skb_size, next_skb_size;
^
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new TCP stats to record the number of reordering events seen
and expose it in both tcp_info (TCP_INFO) and opt_stats
(SOF_TIMESTAMPING_OPT_STATS).
Application can use this stats to track the frequency of the reordering
events in addition to the existing reordering stats which tracks the
magnitude of the latest reordering event.
Note: this new stats tracks reordering events triggered by ACKs, which
could often be fewer than the actual number of packets being delivered
out-of-order.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new TCP stat to record the number of DSACK blocks received
(RFC4989 tcpEStatsStackDSACKDups) and expose it in both tcp_info
(TCP_INFO) and opt_stats (SOF_TIMESTAMPING_OPT_STATS).
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new TCP stat to record the number of bytes retransmitted
(RFC4898 tcpEStatsPerfOctetsRetrans) and expose it in both tcp_info
(TCP_INFO) and opt_stats (SOF_TIMESTAMPING_OPT_STATS).
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new TCP stat to record the number of bytes sent
(RFC4898 tcpEStatsPerfHCDataOctetsOut) and expose it in both tcp_info
(TCP_INFO) and opt_stats (SOF_TIMESTAMPING_OPT_STATS).
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to refactor the calculation of the size of opt_stats to a helper
function to make the code cleaner and easier for later changes.
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may make offloading decision based on whether
ip_forward_update_priority is enabled or not. Therefore distribute
netevent notifications to give them a chance to react to a change.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After IPv4 packets are forwarded, the priority of the corresponding SKB
is updated according to the TOS field of IPv4 header. This overrides any
prioritization done earlier by e.g. an skbedit action or ingress-qos-map
defined at a vlan device.
Such overriding may not always be desirable. Even if the packet ends up
being routed, which implies this is an L3 network node, an administrator
may wish to preserve whatever prioritization was done earlier on in the
pipeline.
Therefore introduce a sysctl that controls this behavior. Keep the
default value at 1 to maintain backward-compatible behavior.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The construction "net->ipv4.sysctl_ip_nonlocal_bind || inet->freebind
|| inet->transparent" is present three times and its IPv6 counterpart
is also present three times. We introduce two small helpers to
characterize these tests uniformly.
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_frag_queue() might call pskb_pull() on one skb that
is already in the fragment queue.
We need to take care of possible truesize change, or we
might have an imbalance of the netns frags memory usage.
IPv6 is immune to this bug, because RFC5722, Section 4,
amended by Errata ID 3089 states :
When reassembling an IPv6 datagram, if
one or more its constituent fragments is determined to be an
overlapping fragment, the entire datagram (and any constituent
fragments) MUST be silently discarded.
Fixes: 158f323b98 ("net: adjust skb->truesize in pskb_expand_head()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently check current frags memory usage only when
a new frag queue is created. This allows attackers to first
consume the memory budget (default : 4 MB) creating thousands
of frag queues, then sending tiny skbs to exceed high_thresh
limit by 2 to 3 order of magnitude.
Note that before commit 648700f76b ("inet: frags: use rhashtables
for reassembly units"), work queue could be starved under DOS,
getting no cpu cycles.
After commit 648700f76b, only the per frag queue timer can eventually
remove an incomplete frag queue and its skbs.
Fixes: b13d3cbfb8 ("inet: frag: move eviction of queues to work queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jann Horn <jannh@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Peter Oskolkov <posk@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wait_address argument is always directly derived from the filp
argument, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the feature described in rfc1812#section-5.3.5.2
and rfc2644. It allows the router to forward directed broadcast when
sysctl bc_forwarding is enabled.
Note that this feature could be done by iptables -j TEE, but it would
cause some problems:
- target TEE's gateway param has to be set with a specific address,
and it's not flexible especially when the route wants forward all
directed broadcasts.
- this duplicates the directed broadcasts so this may cause side
effects to applications.
Besides, to keep consistent with other os router like BSD, it's also
necessary to implement it in the route rx path.
Note that route cache needs to be flushed when bc_forwarding is
changed.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some very small BDPs (with just a few packets) there was a
quantization effect where the target number of packets in flight
during the super-unity-gain (1.25x) phase of gain cycling was
implicitly truncated to a number of packets no larger than the normal
unity-gain (1.0x) phase of gain cycling. This meant that in multi-flow
scenarios some flows could get stuck with a lower bandwidth, because
they did not push enough packets inflight to discover that there was
more bandwidth available. This was really only an issue in multi-flow
LAN scenarios, where RTTs and BDPs are low enough for this to be an
issue.
This fix ensures that gain cycling can raise inflight for small BDPs
by ensuring that in PROBE_BW mode target inflight values with a
super-unity gain are always greater than inflight values with a gain
<= 1. Importantly, this applies whether the inflight value is
calculated for use as a cwnd value, or as a target inflight value for
the end of the super-unity phase in bbr_is_next_cycle_phase() (both
need to be bigger to ensure we can probe with more packets in flight
reliably).
This is a candidate fix for stable releases.
Fixes: 0f8782ea14 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Priyaranjan Jha <priyarjha@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove BUG_ON() from fib_compute_spec_dst routine and check
in_dev pointer during flowi4 data structure initialization.
fib_compute_spec_dst routine can be run concurrently with device removal
where ip_ptr net_device pointer is set to NULL. This can happen
if userspace enables pkt info on UDP rx socket and the device
is removed while traffic is flowing
Fixes: 35ebf65e85 ("ipv4: Create and use fib_compute_spec_dst() helper")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2018-07-27
1) Extend the output_mark to also support the input direction
and masking the mark values before applying to the skb.
2) Add a new lookup key for the upcomming xfrm interfaces.
3) Extend the xfrm lookups to match xfrm interface IDs.
4) Add virtual xfrm interfaces. The purpose of these interfaces
is to overcome the design limitations that the existing
VTI devices have.
The main limitations that we see with the current VTI are the
following:
VTI interfaces are L3 tunnels with configurable endpoints.
For xfrm, the tunnel endpoint are already determined by the SA.
So the VTI tunnel endpoints must be either the same as on the
SA or wildcards. In case VTI tunnel endpoints are same as on
the SA, we get a one to one correlation between the SA and
the tunnel. So each SA needs its own tunnel interface.
On the other hand, we can have only one VTI tunnel with
wildcard src/dst tunnel endpoints in the system because the
lookup is based on the tunnel endpoints. The existing tunnel
lookup won't work with multiple tunnels with wildcard
tunnel endpoints. Some usecases require more than on
VTI tunnel of this type, for example if somebody has multiple
namespaces and every namespace requires such a VTI.
VTI needs separate interfaces for IPv4 and IPv6 tunnels.
So when routing to a VTI, we have to know to which address
family this traffic class is going to be encapsulated.
This is a lmitation because it makes routing more complex
and it is not always possible to know what happens behind the
VTI, e.g. when the VTI is move to some namespace.
VTI works just with tunnel mode SAs. We need generic interfaces
that ensures transfomation, regardless of the xfrm mode and
the encapsulated address family.
VTI is configured with a combination GRE keys and xfrm marks.
With this we have to deal with some extra cases in the generic
tunnel lookup because the GRE keys on the VTI are actually
not GRE keys, the GRE keys were just reused for something else.
All extensions to the VTI interfaces would require to add
even more complexity to the generic tunnel lookup.
So to overcome this, we developed xfrm interfaces with the
following design goal:
It should be possible to tunnel IPv4 and IPv6 through the same
interface.
No limitation on xfrm mode (tunnel, transport and beet).
Should be a generic virtual interface that ensures IPsec
transformation, no need to know what happens behind the
interface.
Interfaces should be configured with a new key that must match a
new policy/SA lookup key.
The lookup logic should stay in the xfrm codebase, no need to
change or extend generic routing and tunnel lookups.
Should be possible to use IPsec hardware offloads of the underlying
interface.
5) Remove xfrm pcpu policy cache. This was added after the flowcache
removal, but it turned out to make things even worse.
From Florian Westphal.
6) Allow to update the set mark on SA updates.
From Nathan Harold.
7) Convert some timestamps to time64_t.
From Arnd Bergmann.
8) Don't check the offload_handle in xfrm code,
it is an opaque data cookie for the driver.
From Shannon Nelson.
9) Remove xfrmi interface ID from flowi. After this pach
no generic code is touched anymore to do xfrm interface
lookups. From Benedict Wong.
10) Allow to update the xfrm interface ID on SA updates.
From Nathan Harold.
11) Don't pass zero to ERR_PTR() in xfrm_resolve_and_create_bundle.
From YueHaibing.
12) Return more detailed errors on xfrm interface creation.
From Benedict Wong.
13) Use PTR_ERR_OR_ZERO instead of IS_ERR + PTR_ERR.
From the kbuild test robot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
net/ipv4/igmp.c:1391:6: warning:
symbol '__ip_mc_inc_group' was not declared. Should it be static?
Fixes: 6e2059b53f ("ipv4/igmp: init group mode as INCLUDE when join source group")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
net/ipv4/tcp_timer.c:25:5: warning:
symbol 'tcp_retransmit_stamp' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported a read beyond the end of the skb head when returning
IPV6_ORIGDSTADDR:
BUG: KMSAN: kernel-infoleak in put_cmsg+0x5ef/0x860 net/core/scm.c:242
CPU: 0 PID: 4501 Comm: syz-executor128 Not tainted 4.17.0+ #9
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x185/0x1d0 lib/dump_stack.c:113
kmsan_report+0x188/0x2a0 mm/kmsan/kmsan.c:1125
kmsan_internal_check_memory+0x138/0x1f0 mm/kmsan/kmsan.c:1219
kmsan_copy_to_user+0x7a/0x160 mm/kmsan/kmsan.c:1261
copy_to_user include/linux/uaccess.h:184 [inline]
put_cmsg+0x5ef/0x860 net/core/scm.c:242
ip6_datagram_recv_specific_ctl+0x1cf3/0x1eb0 net/ipv6/datagram.c:719
ip6_datagram_recv_ctl+0x41c/0x450 net/ipv6/datagram.c:733
rawv6_recvmsg+0x10fb/0x1460 net/ipv6/raw.c:521
[..]
This logic and its ipv4 counterpart read the destination port from
the packet at skb_transport_offset(skb) + 4.
With MSG_MORE and a local SOCK_RAW sender, syzbot was able to cook a
packet that stores headers exactly up to skb_transport_offset(skb) in
the head and the remainder in a frag.
Call pskb_may_pull before accessing the pointer to ensure that it lies
in skb head.
Link: http://lkml.kernel.org/r/CAF=yD-LEJwZj5a1-bAAj2Oy_hKmGygV6rsJ_WOrAYnv-fnayiQ@mail.gmail.com
Reported-by: syzbot+9adb4b567003cac781f0@syzkaller.appspotmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several files have extra line at end of file.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case skb in out_or_order_queue is the result of
multiple skbs coalescing, we would like to get a proper gso_segs
counter tracking, so that future tcp_drop() can report an accurate
number.
I chose to not implement this tracking for skbs in receive queue,
since they are not dropped, unless socket is disconnected.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be able to give better diagnostics and detect
malicious traffic, we need to have better sk->sk_drops tracking.
Fixes: 9f5afeae51 ("tcp: use an RB tree for ooo receive queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case an attacker feeds tiny packets completely out of order,
tcp_collapse_ofo_queue() might scan the whole rb-tree, performing
expensive copies, but not changing socket memory usage at all.
1) Do not attempt to collapse tiny skbs.
2) Add logic to exit early when too many tiny skbs are detected.
We prefer not doing aggressive collapsing (which copies packets)
for pathological flows, and revert to tcp_prune_ofo_queue() which
will be less expensive.
In the future, we might add the possibility of terminating flows
that are proven to be malicious.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right after a TCP flow is created, receiving tiny out of order
packets allways hit the condition :
if (atomic_read(&sk->sk_rmem_alloc) >= sk->sk_rcvbuf)
tcp_clamp_window(sk);
tcp_clamp_window() increases sk_rcvbuf to match sk_rmem_alloc
(guarded by tcp_rmem[2])
Calling tcp_collapse_ofo_queue() in this case is not useful,
and offers a O(N^2) surface attack to malicious peers.
Better not attempt anything before full queue capacity is reached,
forcing attacker to spend lots of resource and allow us to more
easily detect the abuse.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Juha-Matti Tilli reported that malicious peers could inject tiny
packets in out_of_order_queue, forcing very expensive calls
to tcp_collapse_ofo_queue() and tcp_prune_ofo_queue() for
every incoming packet. out_of_order_queue rb-tree can contain
thousands of nodes, iterating over all of them is not nice.
Before linux-4.9, we would have pruned all packets in ofo_queue
in one go, every XXXX packets. XXXX depends on sk_rcvbuf and skbs
truesize, but is about 7000 packets with tcp_rmem[2] default of 6 MB.
Since we plan to increase tcp_rmem[2] in the future to cope with
modern BDP, can not revert to the old behavior, without great pain.
Strategy taken in this patch is to purge ~12.5 % of the queue capacity.
Fixes: 36a6503fed ("tcp: refine tcp_prune_ofo_queue() to not drop all packets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Juha-Matti Tilli <juha-matti.tilli@iki.fi>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb hash for locally generated ip[v6] fragments belonging
to the same datagram can vary in several circumstances:
* for connected UDP[v6] sockets, the first fragment get its hash
via set_owner_w()/skb_set_hash_from_sk()
* for unconnected IPv6 UDPv6 sockets, the first fragment can get
its hash via ip6_make_flowlabel()/skb_get_hash_flowi6(), if
auto_flowlabel is enabled
For the following frags the hash is usually computed via
skb_get_hash().
The above can cause OoO for unconnected IPv6 UDPv6 socket: in that
scenario the egress tx queue can be selected on a per packet basis
via the skb hash.
It may also fool flow-oriented schedulers to place fragments belonging
to the same datagram in different flows.
Fix the issue by copying the skb hash from the head frag into
the others at fragmentation time.
Before this commit:
perf probe -a "dev_queue_xmit skb skb->hash skb->l4_hash:b1@0/8 skb->sw_hash:b1@1/8"
netperf -H $IPV4 -t UDP_STREAM -l 5 -- -m 2000 -n &
perf record -e probe:dev_queue_xmit -e probe:skb_set_owner_w -a sleep 0.1
perf script
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=3713014309 l4_hash=1 sw_hash=0
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=0 l4_hash=0 sw_hash=0
After this commit:
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=2171763177 l4_hash=1 sw_hash=0
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=2171763177 l4_hash=1 sw_hash=0
Fixes: b73c3d0e4f ("net: Save TX flow hash in sock and set in skbuf on xmit")
Fixes: 67800f9b1f ("ipv6: Call skb_get_hash_flowi6 to get skb->hash in ip6_make_flowlabel")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two scenarios that we will restore deleted records. The first is
when device down and up(or unmap/remap). In this scenario the new filter
mode is same with previous one. Because we get it from in_dev->mc_list and
we do not touch it during device down and up.
The other scenario is when a new socket join a group which was just delete
and not finish sending status reports. In this scenario, we should use the
current filter mode instead of restore old one. Here are 4 cases in total.
old_socket new_socket before_fix after_fix
IN(A) IN(A) ALLOW(A) ALLOW(A)
IN(A) EX( ) TO_IN( ) TO_EX( )
EX( ) IN(A) TO_EX( ) ALLOW(A)
EX( ) EX( ) TO_EX( ) TO_EX( )
Fixes: 24803f38a5 (igmp: do not remove igmp souce list info when set link down)
Fixes: 1666d49e1d (mld: do not remove mld souce list info when set link down)
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the mode parameter for igmp/igmp6_group_added as we can get it
from first parameter.
Fixes: 6e2059b53f (ipv4/igmp: init group mode as INCLUDE when join source group)
Fixes: c7ea20c9da (ipv6/mcast: init as INCLUDE when join SSM INCLUDE group)
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create the tcp_clamp_rto_to_user_timeout() helper routine. To calculate
the correct rto, so that the TCP_USER_TIMEOUT socket option is more
accurate. Taking suggestions and feedback into account from
Eric Dumazet, Neal Cardwell and David Laight. Due to the 1st commit we
can avoid the msecs_to_jiffies() and jiffies_to_msecs() dance.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a seperate helper routine as per Neal Cardwells suggestion. To
be used by the final commit in this series and retransmits_timed_out().
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparatory commit. Part of this series that improves the
socket TCP_USER_TIMEOUT option accuracy. Implement Eric Dumazets idea
to convert icsk->icsk_user_timeout from jiffies to msecs. To eliminate
the msecs_to_jiffies() and jiffies_to_msecs() dance in future.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree:
1) No need to set ttl from reject action for the bridge family, from
Taehee Yoo.
2) Use a fixed timeout for flow that are passed up from the flowtable
to conntrack, from Florian Westphal.
3) More preparation patches for tproxy support for nf_tables, from Mate
Eckl.
4) Remove unnecessary indirection in core IPv6 checksum function, from
Florian Westphal.
5) Use nf_ct_get_tuplepr() from openvswitch, instead of opencoding it.
From Florian Westphal.
6) socket match now selects socket infrastructure, instead of depending
on it. From Mate Eckl.
7) Patch series to simplify conntrack tuple building/parsing from packet
path and ctnetlink, from Florian Westphal.
8) Fetch timeout policy from protocol helpers, instead of doing it from
core, from Florian Westphal.
9) Merge IPv4 and IPv6 protocol trackers into conntrack core, from
Florian Westphal.
10) Depend on CONFIG_NF_TABLES_IPV6 and CONFIG_IP6_NF_IPTABLES
respectively, instead of IPV6. Patch from Mate Eckl.
11) Add specific function for garbage collection in conncount,
from Yi-Hung Wei.
12) Catch number of elements in the connlimit list, from Yi-Hung Wei.
13) Move locking to nf_conncount, from Yi-Hung Wei.
14) Series of patches to add lockless tree traversal in nf_conncount,
from Yi-Hung Wei.
15) Resolve clash in matching conntracks when race happens, from
Martynas Pumputis.
16) If connection entry times out, remove template entry from the
ip_vs_conn_tab table to improve behaviour under flood, from
Julian Anastasov.
17) Remove useless parameter from nf_ct_helper_ext_add(), from Gao feng.
18) Call abort from 2-phase commit protocol before requesting modules,
make sure this is done under the mutex, from Florian Westphal.
19) Grab module reference when starting transaction, also from Florian.
20) Dynamically allocate expression info array for pre-parsing, from
Florian.
21) Add per netns mutex for nf_tables, from Florian Westphal.
22) A couple of patches to simplify and refactor nf_osf code to prepare
for nft_osf support.
23) Break evaluation on missing socket, from Mate Eckl.
24) Allow to match socket mark from nft_socket, from Mate Eckl.
25) Remove dependency on nf_defrag_ipv6, now that IPv6 tracker is
built-in into nf_conntrack. From Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Per DCTCP RFC8257 (Section 3.2) the ACK reflecting the CE status change
has to be sent immediately so the sender can respond quickly:
""" When receiving packets, the CE codepoint MUST be processed as follows:
1. If the CE codepoint is set and DCTCP.CE is false, set DCTCP.CE to
true and send an immediate ACK.
2. If the CE codepoint is not set and DCTCP.CE is true, set DCTCP.CE
to false and send an immediate ACK.
"""
Previously DCTCP implementation may continue to delay the ACK. This
patch fixes that to implement the RFC by forcing an immediate ACK.
Tested with this packetdrill script provided by Larry Brakmo
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
0.000 setsockopt(3, SOL_TCP, TCP_CONGESTION, "dctcp", 5) = 0
0.000 bind(3, ..., ...) = 0
0.000 listen(3, 1) = 0
0.100 < [ect0] SEW 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
0.100 > SE. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 8>
0.110 < [ect0] . 1:1(0) ack 1 win 257
0.200 accept(3, ..., ...) = 4
+0 setsockopt(4, SOL_SOCKET, SO_DEBUG, [1], 4) = 0
0.200 < [ect0] . 1:1001(1000) ack 1 win 257
0.200 > [ect01] . 1:1(0) ack 1001
0.200 write(4, ..., 1) = 1
0.200 > [ect01] P. 1:2(1) ack 1001
0.200 < [ect0] . 1001:2001(1000) ack 2 win 257
+0.005 < [ce] . 2001:3001(1000) ack 2 win 257
+0.000 > [ect01] . 2:2(0) ack 2001
// Previously the ACK below would be delayed by 40ms
+0.000 > [ect01] E. 2:2(0) ack 3001
+0.500 < F. 9501:9501(0) ack 4 win 257
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when a DCTCP receiver delays an ACK and receive a
data packet with a different CE mark from the previous one's, it
sends two immediate ACKs acking previous and latest sequences
respectly (for ECN accounting).
Previously sending the first ACK may mark off the delayed ACK timer
(tcp_event_ack_sent). This may subsequently prevent sending the
second ACK to acknowledge the latest sequence (tcp_ack_snd_check).
The culprit is that tcp_send_ack() assumes it always acknowleges
the latest sequence, which is not true for the first special ACK.
The fix is to not make the assumption in tcp_send_ack and check the
actual ack sequence before cancelling the delayed ACK. Further it's
safer to pass the ack sequence number as a local variable into
tcp_send_ack routine, instead of intercepting tp->rcv_nxt to avoid
future bugs like this.
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor and create helpers to send the special ACK in DCTCP.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The offload_handle should be an opaque data cookie for the driver
to use, much like the data cookie for a timer or alarm callback.
Thus, the XFRM stack should not be checking for non-zero, because
the driver might use that to store an array reference, which could
be zero, or some other zero but meaningful value.
We can remove the checks for non-zero because there are plenty
other attributes also being checked to see if there is an offload
in place for the SA in question.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Attempt to make cryptic TCP seq number error messages clearer by
(1) identifying the source of the message as "TCP", (2) identifying the
errors as "seq # bug", and (3) grouping the field identifiers and values
by separating them with commas.
E.g., the following message is changed from:
recvmsg bug 2: copied 73BCB6CD seq 70F17CBE rcvnxt 73BCB9AA fl 0
WARNING: CPU: 2 PID: 1501 at /linux/net/ipv4/tcp.c:1881 tcp_recvmsg+0x649/0xb90
to:
TCP recvmsg seq # bug 2: copied 73BCB6CD, seq 70F17CBE, rcvnxt 73BCB9AA, fl 0
WARNING: CPU: 2 PID: 1501 at /linux/net/ipv4/tcp.c:2011 tcp_recvmsg+0x694/0xba0
Suggested-by: 積丹尼 Dan Jacobson <jidanni@jidanni.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This unifies ipv4 and ipv6 protocol trackers and removes the l3proto
abstraction.
This gets rid of all l3proto indirect calls and the need to do
a lookup on the function to call for l3 demux.
It increases module size by only a small amount (12kbyte), so this reduces
size because nf_conntrack.ko is useless without either nf_conntrack_ipv4
or nf_conntrack_ipv6 module.
before:
text data bss dec hex filename
7357 1088 0 8445 20fd nf_conntrack_ipv4.ko
7405 1084 4 8493 212d nf_conntrack_ipv6.ko
72614 13689 236 86539 1520b nf_conntrack.ko
19K nf_conntrack_ipv4.ko
19K nf_conntrack_ipv6.ko
179K nf_conntrack.ko
after:
text data bss dec hex filename
79277 13937 236 93450 16d0a nf_conntrack.ko
191K nf_conntrack.ko
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Correct previous bad attempt at allowing sockets to come out of TCP
repair without sending window probes. To avoid changing size of
the repair variable in struct tcp_sock, this lets the decision for
sending probes or not to be made when coming out of repair by
introducing two ways to turn it off.
v2:
* Remove erroneous comment; defines now make behavior clear
Fixes: 70b7ff1302 ("tcp: allow user to create repair socket without window probes")
Signed-off-by: Stefan Baranoff <sbaranoff@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on RFC3376 5.1
If no interface
state existed for that multicast address before the change (i.e., the
change consisted of creating a new per-interface record), or if no
state exists after the change (i.e., the change consisted of deleting
a per-interface record), then the "non-existent" state is considered
to have a filter mode of INCLUDE and an empty source list.
Which means a new multicast group should start with state IN().
Function ip_mc_join_group() works correctly for IGMP ASM(Any-Source Multicast)
mode. It adds a group with state EX() and inits crcount to mc_qrv,
so the kernel will send a TO_EX() report message after adding group.
But for IGMPv3 SSM(Source-specific multicast) JOIN_SOURCE_GROUP mode, we
split the group joining into two steps. First we join the group like ASM,
i.e. via ip_mc_join_group(). So the state changes from IN() to EX().
Then we add the source-specific address with INCLUDE mode. So the state
changes from EX() to IN(A).
Before the first step sends a group change record, we finished the second
step. So we will only send the second change record. i.e. TO_IN(A).
Regarding the RFC stands, we should actually send an ALLOW(A) message for
SSM JOIN_SOURCE_GROUP as the state should mimic the 'IN() to IN(A)'
transition.
The issue was exposed by commit a052517a8f ("net/multicast: should not
send source list records when have filter mode change"). Before this change,
we used to send both ALLOW(A) and TO_IN(A). After this change we only send
TO_IN(A).
Fix it by adding a new parameter to init group mode. Also add new wrapper
functions so we don't need to change too much code.
v1 -> v2:
In my first version I only cleared the group change record. But this is not
enough. Because when a new group join, it will init as EXCLUDE and trigger
an filter mode change in ip/ip6_mc_add_src(), which will clear all source
addresses' sf_crcount. This will prevent early joined address sending state
change records if multi source addressed joined at the same time.
In v2 patch, I fixed it by directly initializing the mode to INCLUDE for SSM
JOIN_SOURCE_GROUP. I also split the original patch into two separated patches
for IPv4 and IPv6.
Fixes: a052517a8f ("net/multicast: should not send source list records when have filter mode change")
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not needed, we can have the l4trackers fetch it themselvs.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Handle it in the core instead.
ipv6_skip_exthdr() is built-in even if ipv6 is a module, i.e. this
doesn't create an ipv6 dependency.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Its simpler to just handle it directly in nf_ct_invert_tuple().
Also gets rid of need to pass l3proto pointer to resolve_conntrack().
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
handle everything from ctnetlink directly.
After all these years we still only support ipv4 and ipv6, so it
seems reasonable to remove l3 protocol tracker support and instead
handle ipv4/ipv6 from a common, always builtin inet tracker.
Step 1: Get rid of all the l3proto->func() calls.
Start with ctnetlink, then move on to packet-path ones.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
allows to make nf_ip_checksum_partial static, it no longer
has an external caller.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Prevent coalescing of decrypted and encrypted SKBs in GRO
and TCP layer.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-07-15
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Various different arm32 JIT improvements in order to optimize code emission
and make the JIT code itself more robust, from Russell.
2) Support simultaneous driver and offloaded XDP in order to allow for advanced
use-cases where some work is offloaded to the NIC and some to the host. Also
add ability for bpftool to load programs and maps beyond just the cgroup case,
from Jakub.
3) Add BPF JIT support in nfp for multiplication as well as division. For the
latter in particular, it uses the reciprocal algorithm to emulate it, from Jiong.
4) Add BTF pretty print functionality to bpftool in plain and JSON output
format, from Okash.
5) Add build and installation to the BPF helper man page into bpftool, from Quentin.
6) Add a TCP BPF callback for listening sockets which is triggered right after
the socket transitions to TCP_LISTEN state, from Andrey.
7) Add a new cgroup tree command to bpftool which iterates over the whole cgroup
tree and prints all attached programs, from Roman.
8) Improve xdp_redirect_cpu sample to support parsing of double VLAN tagged
packets, from Jesper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new TCP-BPF callback that is called on listen(2) right after socket
transition to TCP_LISTEN state.
It fills the gap for listening sockets in TCP-BPF. For example BPF
program can set BPF_SOCK_OPS_STATE_CB_FLAG when socket becomes listening
and track later transition from TCP_LISTEN to TCP_CLOSE with
BPF_SOCK_OPS_STATE_CB callback.
Before there was no way to do it with TCP-BPF and other options were
much harder to work with. E.g. socket state tracking can be done with
tracepoints (either raw or regular) but they can't be attached to cgroup
and their lifetime has to be managed separately.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
tcp_rcv_nxt_update() is already executed in tcp_data_queue().
This line is redundant.
See bellow,
tcp_queue_rcv
tcp_rcv_nxt_update(tcp_sk(sk), TCP_SKB_CB(skb)->end_seq);
tcp_rcv_nxt_update(tp, TCP_SKB_CB(skb)->end_seq); <<<< redundant
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After fixing the way DCTCP tracking delayed ACKs, the delayed-ACK
related callbacks are no longer needed
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, when a data segment was sent an ACK was piggybacked
on the data segment without generating a CA_EVENT_NON_DELAYED_ACK
event to notify congestion control modules. So the DCTCP
ca->delayed_ack_reserved flag could incorrectly stay set when
in fact there were no delayed ACKs being reserved. This could result
in sending a special ECN notification ACK that carries an older
ACK sequence, when in fact there was no need for such an ACK.
DCTCP keeps track of the delayed ACK status with its own separate
state ca->delayed_ack_reserved. Previously it may accidentally cancel
the delayed ACK without updating this field upon sending a special
ACK that carries a older ACK sequence. This inconsistency would
lead to DCTCP receiver never acknowledging the latest data until the
sender times out and retry in some cases.
Packetdrill script (provided by Larry Brakmo)
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
0.000 setsockopt(3, SOL_TCP, TCP_CONGESTION, "dctcp", 5) = 0
0.000 bind(3, ..., ...) = 0
0.000 listen(3, 1) = 0
0.100 < [ect0] SEW 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
0.100 > SE. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 8>
0.110 < [ect0] . 1:1(0) ack 1 win 257
0.200 accept(3, ..., ...) = 4
0.200 < [ect0] . 1:1001(1000) ack 1 win 257
0.200 > [ect01] . 1:1(0) ack 1001
0.200 write(4, ..., 1) = 1
0.200 > [ect01] P. 1:2(1) ack 1001
0.200 < [ect0] . 1001:2001(1000) ack 2 win 257
0.200 write(4, ..., 1) = 1
0.200 > [ect01] P. 2:3(1) ack 2001
0.200 < [ect0] . 2001:3001(1000) ack 3 win 257
0.200 < [ect0] . 3001:4001(1000) ack 3 win 257
0.200 > [ect01] . 3:3(0) ack 4001
0.210 < [ce] P. 4001:4501(500) ack 3 win 257
+0.001 read(4, ..., 4500) = 4500
+0 write(4, ..., 1) = 1
+0 > [ect01] PE. 3:4(1) ack 4501
+0.010 < [ect0] W. 4501:5501(1000) ack 4 win 257
// Previously the ACK sequence below would be 4501, causing a long RTO
+0.040~+0.045 > [ect01] . 4:4(0) ack 5501 // delayed ack
+0.311 < [ect0] . 5501:6501(1000) ack 4 win 257 // More data
+0 > [ect01] . 4:4(0) ack 6501 // now acks everything
+0.500 < F. 9501:9501(0) ack 4 win 257
Reported-by: Larry Brakmo <brakmo@fb.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for IGMPMSG_WRVIFWHOLE which is used to pass
full packet and real vif id when the incoming interface is wrong.
While the RP and FHR are setting up state we need to be sending the
registers encapsulated with all the data inside otherwise we lose it.
The RP then decapsulates it and forwards it to the interested parties.
Currently with WRONGVIF we can only be sending empty register packets
and will lose that data.
This behaviour can be enabled by using MRT_PIM with
val == IGMPMSG_WRVIFWHOLE. This doesn't prevent IGMPMSG_WRONGVIF from
happening, it happens in addition to it, also it is controlled by the same
throttling parameters as WRONGVIF (i.e. 1 packet per 3 seconds currently).
Both messages are generated to keep backwards compatibily and avoid
breaking someone who was enabling MRT_PIM with val == 4, since any
positive val is accepted and treated the same.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 5fa12739a5 ("net: ipv4: listify ip_rcv_finish") calling
dst_input(skb) was split-out. The ip_sublist_rcv_finish() just calls
dst_input(skb) in a loop.
The problem is that ip_sublist_rcv_finish() forgot to remove the SKB
from the list before invoking dst_input(). Further more we need to
clear skb->next as other parts of the network stack use another kind
of SKB lists for xmit_more (see dev_hard_start_xmit).
A crash occurs if e.g. dst_input() invoke ip_forward(), which calls
dst_output()/ip_output() that eventually calls __dev_queue_xmit() +
sch_direct_xmit(), and a crash occurs in validate_xmit_skb_list().
This patch only fixes the crash, but there is a huge potential for
a performance boost if we can pass an SKB-list through to ip_forward.
Fixes: 5fa12739a5 ("net: ipv4: listify ip_rcv_finish")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using get_seconds() for timestamps is deprecated since it can lead
to overflows on 32-bit systems. While the interface generally doesn't
overflow until year 2106, the specific implementation of the TCP PAWS
algorithm breaks in 2038 when the intermediate signed 32-bit timestamps
overflow.
A related problem is that the local timestamps in CLOCK_REALTIME form
lead to unexpected behavior when settimeofday is called to set the system
clock backwards or forwards by more than 24 days.
While the first problem could be solved by using an overflow-safe method
of comparing the timestamps, a nicer solution is to use a monotonic
clocksource with ktime_get_seconds() that simply doesn't overflow (at
least not until 136 years after boot) and that doesn't change during
settimeofday().
To make 32-bit and 64-bit architectures behave the same way here, and
also save a few bytes in the tcp_options_received structure, I'm changing
the type to a 32-bit integer, which is now safe on all architectures.
Finally, the ts_recent_stamp field also (confusingly) gets used to store
a jiffies value in tcp_synq_overflow()/tcp_synq_no_recent_overflow().
This is currently safe, but changing the type to 32-bit requires
some small changes there to keep it working.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under rare conditions where repair code may be used it is possible that
window probes are either unnecessary or undesired. If the user knows that
window probes are not wanted or needed this change allows them to skip
sending them when a socket comes out of repair.
Signed-off-by: Stefan Baranoff <sbaranoff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug where the sequence numbers of a socket created using
TCP repair functionality are lower than set after connect is called.
This occurs when the repair socket overlaps with a TIME-WAIT socket and
triggers the re-use code. The amount lower is equal to the number of times
that a particular IP/port set is re-used and then put back into TIME-WAIT.
Re-using the first time the sequence number is 1 lower, closing that socket
and then re-opening (with repair) a new socket with the same addresses/ports
puts the sequence number 2 lower than set via setsockopt. The third time is
3 lower, etc. I have not tested what the limit of this acrewal is, if any.
The fix is, if a socket is in repair mode, to respect the already set
sequence number and timestamp when it would have already re-used the
TIME-WAIT socket.
Signed-off-by: Stefan Baranoff <sbaranoff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Congestion control algorithms, which access the rate sample
through the tcp_cong_control function, only have access to the maximum
of the send and receive interval, for cases where the acknowledgment
rate may be inaccurate due to ACK compression or decimation. Algorithms
may want to use send rates and receive rates as separate signals.
Signed-off-by: Deepti Raghavan <deeptir@mit.edu>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 74d4a8f8d3 ("tcp: remove sk_can_gso() use"), the code
doesn't care whether the interface supports SG.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree:
1) Missing module autoloadfor icmp and icmpv6 x_tables matches,
from Florian Westphal.
2) Possible non-linear access to TCP header from tproxy, from
Mate Eckl.
3) Do not allow rbtree to be used for single elements, this patch
moves all set backend into one single module since such thing
can only happen if hashtable module is explicitly blacklisted,
which should not ever be done.
4) Reject error and standard targets from nft_compat for sanity
reasons, they are never used from there.
5) Don't crash on double hashsize module parameter, from Andrey
Ryabinin.
6) Drop dst on skb before placing it in the fragmentation
reassembly queue, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In both tcp_splice_read() and tcp_recvmsg(), we already test
sock_flag(sk, SOCK_DONE) right before evaluating sk->sk_state,
so "!sock_flag(sk, SOCK_DONE)" is always true.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_zerocopy_receive() relies on tcp_inq() to limit number of bytes
requested by user.
syzbot found that after tcp_disconnect(), tcp_inq() was returning
a stale value (number of bytes in queue before the disconnect).
Note that after this patch, ioctl(fd, SIOCINQ, &val) is also fixed
and returns 0, so this might be a candidate for all known linux kernels.
While we are at this, we probably also should clear urg_data to
avoid other syzkaller reports after it discovers how to deal with
urgent data.
syzkaller repro :
socket(PF_INET, SOCK_STREAM, IPPROTO_IP) = 3
bind(3, {sa_family=AF_INET, sin_port=htons(20000), sin_addr=inet_addr("224.0.0.1")}, 16) = 0
connect(3, {sa_family=AF_INET, sin_port=htons(20000), sin_addr=inet_addr("127.0.0.1")}, 16) = 0
send(3, ..., 4096, 0) = 4096
connect(3, {sa_family=AF_UNSPEC, sa_data="\0\0\0\0\0\0\0\0\0\0\0\0\0\0"}, 128) = 0
getsockopt(3, SOL_TCP, TCP_ZEROCOPY_RECEIVE, ..., [16]) = 0 // CRASH
Fixes: 05255b823a ("tcp: add TCP_ZEROCOPY_RECEIVE support for zerocopy receive")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the low threshold to 0 has no effect on frags allocation,
we need to clear high_thresh instead.
The code was pre-existent to commit 648700f76b ("inet: frags:
use rhashtables for reassembly units"), but before the above,
such assignment had a different role: prevent concurrent eviction
from the worker and the netns cleanup helper.
Fixes: 648700f76b ("inet: frags: use rhashtables for reassembly units")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tcp_diag_destroy closes a TCP_NEW_SYN_RECV socket, it first
frees it by calling inet_csk_reqsk_queue_drop_and_and_put in
tcp_abort, and then frees it again by calling sock_gen_put.
Since tcp_abort only has one caller, and all the other codepaths
in tcp_abort don't free the socket, just remove the free in that
function.
Cc: David Ahern <dsa@cumulusnetworks.com>
Tested: passes Android sock_diag_test.py, which exercises this codepath
Fixes: d7226c7a4d ("net: diag: Fix refcnt leak in error path destroying socket")
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin reported that icmp replies may not use the address on the device the
echo request is received if the destination address is broadcast. Instead
a route lookup is done without considering VRF context. Fix by setting
oif in flow struct to the master device if it is enslaved. That directs
the lookup to the VRF table. If the device is not enslaved, oif is still
0 so no affect.
Fixes: cd2fbe1b6b ("net: Use VRF device index for lookups on RX")
Reported-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ipc(6)->gso_size is correctly initialized in all callers of
ip(6)_setup_cork, it is safe to unconditionally pass it to the cork.
Link: http://lkml.kernel.org/r/20180619164752.143249-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_shinfo(skb)->tx_flags is derived from sk->sk_tsflags, possibly
after modification by __sock_cmsg_send, by calling sock_tx_timestamp.
The IPv4 and IPv6 paths do this conversion differently. In IPv4, the
individual protocols that support tx timestamps call this function
and store the result in ipc.tx_flags. In IPv6, sock_tx_timestamp is
called in __ip6_append_data.
There is no need to store both tx_flags and ts_flags in the cookie
as one is derived from the other. Convert when setting up the cork
and remove the redundant field. This is similar to IPv6, only have
the conversion happen only once per datagram, in ip(6)_setup_cork.
Also change __ip6_append_data to match __ip_append_data. Only update
tskey if timestamping is enabled with OPT_ID. The SOCK_.. test is
redundant: only valid protocols can have non-zero cork->tx_flags.
After this change the IPv4 and IPv6 logic is the same.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize the cookie in one location to reduce code duplication and
avoid bugs from inconsistent initialization, such as that fixed in
commit 9887cba199 ("ip: limit use of gso_size to udp").
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize the cookie in one location to reduce code duplication and
avoid bugs from inconsistent initialization, such as that fixed in
commit 9887cba199 ("ip: limit use of gso_size to udp").
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a silent out-of-bound read possibility that was present
because of the misuse of this function.
Mostly it was called with a struct udphdr *hp which had only the udphdr
part linearized by the skb_header_pointer, however
nf_tproxy_get_sock_v{4,6} uses it as a tcphdr pointer, so some reads for
tcp specific attributes may be invalid.
Fixes: a583636a83 ("inet: refactor inet[6]_lookup functions to take skb")
Signed-off-by: Máté Eckl <ecklm94@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The low and high values of the net.ipv4.ping_group_range sysctl were
being silently forced to the default disabled state when a write to the
sysctl contained GIDs that didn't map to the associated user namespace.
Confusingly, the sysctl's write operation would return success and then
a subsequent read of the sysctl would indicate that the low and high
values are the overflowgid.
This patch changes the behavior by clearly returning an error when the
sysctl write operation receives a GID range that doesn't map to the
associated user namespace. In such a situation, the previous value of
the sysctl is preserved and that range will be returned in a subsequent
read of the sysctl.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have an L3 master device, l3mdev_ip_rcv() will steal the skb, but
we were returning NET_RX_SUCCESS from ip_rcv_finish_core() which meant
that ip_list_rcv_finish() would keep it on the list. Instead let's
move the l3mdev_ip_rcv() call into the caller, so that our response to
a steal can be different in the single packet path (return
NET_RX_SUCCESS) and the list path (forget this packet and continue).
Fixes: 5fa12739a5 ("net: ipv4: listify ip_rcv_finish")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nft_compat relies on xt_request_find_match to increment
refcount of the module that provides the match/target.
The (builtin) icmp matches did't set the module owner so it
was possible to rmmod ip(6)tables while icmp extensions were still in use.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since callees (ip_rcv_core() and ip_rcv_finish_core()) might free or steal
the skb, we can't use the list_cut_before() method; we can't even do a
list_del(&skb->list) in the drop case, because skb might have already been
freed and reused.
So instead, take each skb off the source list before processing, and add it
to the sublist afterwards if it wasn't freed or stolen.
Fixes: 5fa12739a5 net: ipv4: listify ip_rcv_finish
Fixes: 17266ee939 net: ipv4: listified version of ip_rcv
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a transmit_time field to struct inet_cork, then copy the
timestamp from the CMSG cookie at ip_setup_cork() so we can
safely copy it into the skb later during __ip_make_skb().
For the raw fast path, just perform the copy at raw_send_hdrinc().
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_rcv_finish_core(), if it does not drop, sets skb->dst by either early
demux or route lookup. The last step, calling dst_input(skb), is left to
the caller; in the listified case, we split to form sublists with a common
dst, but then ip_sublist_rcv_finish() just calls dst_input(skb) in a loop.
The next step in listification would thus be to add a list_input() method
to struct dst_entry.
Early demux is an indirect call based on iph->protocol; this is another
opportunity for listification which is not taken here (it would require
slicing up ip_rcv_finish_core() to allow splitting on protocol changes).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also involved adding a way to run a netfilter hook over a list of packets.
Rather than attempting to make netfilter know about lists (which would be
a major project in itself) we just let it call the regular okfn (in this
case ip_rcv_finish()) for any packets it steals, and have it give us back
a list of packets it's synchronously accepted (which normally NF_HOOK
would automatically call okfn() on, but we want to be able to potentially
pass the list to a listified version of okfn().)
The netfilter hooks themselves are indirect calls that still happen per-
packet (see nf_hook_entry_hookfn()), but again, changing that can be left
for future work.
There is potential for out-of-order receives if the netfilter hook ends up
synchronously stealing packets, as they will be processed before any
accepts earlier in the list. However, it was already possible for an
asynchronous accept to cause out-of-order receives, so presumably this is
considered OK.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces __ip_queue_xmit(), through which the callers
can pass tos param into it without having to set inet->tos. For
ipv6, ip6_xmit() already allows passing tclass parameter.
It's needed when some transport protocol doesn't use inet->tos,
like sctp's per transport dscp, which will be added in next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Verify netlink attributes properly in nf_queue, from Eric Dumazet.
2) Need to bump memory lock rlimit for test_sockmap bpf test, from
Yonghong Song.
3) Fix VLAN handling in lan78xx driver, from Dave Stevenson.
4) Fix uninitialized read in nf_log, from Jann Horn.
5) Fix raw command length parsing in mlx5, from Alex Vesker.
6) Cleanup loopback RDS connections upon netns deletion, from Sowmini
Varadhan.
7) Fix regressions in FIB rule matching during create, from Jason A.
Donenfeld and Roopa Prabhu.
8) Fix mpls ether type detection in nfp, from Pieter Jansen van Vuuren.
9) More bpfilter build fixes/adjustments from Masahiro Yamada.
10) Fix XDP_{TX,REDIRECT} flushing in various drivers, from Jesper
Dangaard Brouer.
11) fib_tests.sh file permissions were broken, from Shuah Khan.
12) Make sure BH/preemption is disabled in data path of mac80211, from
Denis Kenzior.
13) Don't ignore nla_parse_nested() return values in nl80211, from
Johannes berg.
14) Properly account sock objects ot kmemcg, from Shakeel Butt.
15) Adjustments to setting bpf program permissions to read-only, from
Daniel Borkmann.
16) TCP Fast Open key endianness was broken, it always took on the host
endiannness. Whoops. Explicitly make it little endian. From Yuching
Cheng.
17) Fix prefix route setting for link local addresses in ipv6, from
David Ahern.
18) Potential Spectre v1 in zatm driver, from Gustavo A. R. Silva.
19) Various bpf sockmap fixes, from John Fastabend.
20) Use after free for GRO with ESP, from Sabrina Dubroca.
21) Passing bogus flags to crypto_alloc_shash() in ipv6 SR code, from
Eric Biggers.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
qede: Adverstise software timestamp caps when PHC is not available.
qed: Fix use of incorrect size in memcpy call.
qed: Fix setting of incorrect eswitch mode.
qed: Limit msix vectors in kdump kernel to the minimum required count.
ipvlan: call dev_change_flags when ipvlan mode is reset
ipv6: sr: fix passing wrong flags to crypto_alloc_shash()
net: fix use-after-free in GRO with ESP
tcp: prevent bogus FRTO undos with non-SACK flows
bpf: sockhash, add release routine
bpf: sockhash fix omitted bucket lock in sock_close
bpf: sockmap, fix smap_list_map_remove when psock is in many maps
bpf: sockmap, fix crash when ipv6 sock is added
net: fib_rules: bring back rule_exists to match rule during add
hv_netvsc: split sub-channel setup into async and sync
net: use dev_change_tx_queue_len() for SIOCSIFTXQLEN
atm: zatm: Fix potential Spectre v1
s390/qeth: consistently re-enable device features
s390/qeth: don't clobber buffer on async TX completion
s390/qeth: avoid using is_multicast_ether_addr_64bits on (u8 *)[6]
s390/qeth: fix race when setting MAC address
...
Since the addition of GRO for ESP, gro_receive can consume the skb and
return -EINPROGRESS. In that case, the lower layer GRO handler cannot
touch the skb anymore.
Commit 5f114163f2 ("net: Add a skb_gro_flush_final helper.") converted
some of the gro_receive handlers that can lead to ESP's gro_receive so
that they wouldn't access the skb when -EINPROGRESS is returned, but
missed other spots, mainly in tunneling protocols.
This patch finishes the conversion to using skb_gro_flush_final(), and
adds a new helper, skb_gro_flush_final_remcsum(), used in VXLAN and
GUE.
Fixes: 5f114163f2 ("net: Add a skb_gro_flush_final helper.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new field to sock_common 'skc_rx_queue_mapping'
which holds the receive queue number for the connection. The Rx queue
is marked in tcp_finish_connect() to allow a client app to do
SO_INCOMING_NAPI_ID after a connect() call to get the right queue
association for a socket. Rx queue is also marked in tcp_conn_request()
to allow syn-ack to go on the right tx-queue associated with
the queue on which syn is received.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SACK is not enabled and the first cumulative ACK after the RTO
retransmission covers more than the retransmitted skb, a spurious
FRTO undo will trigger (assuming FRTO is enabled for that RTO).
The reason is that any non-retransmitted segment acknowledged will
set FLAG_ORIG_SACK_ACKED in tcp_clean_rtx_queue even if there is
no indication that it would have been delivered for real (the
scoreboard is not kept with TCPCB_SACKED_ACKED bits in the non-SACK
case so the check for that bit won't help like it does with SACK).
Having FLAG_ORIG_SACK_ACKED set results in the spurious FRTO undo
in tcp_process_loss.
We need to use more strict condition for non-SACK case and check
that none of the cumulatively ACKed segments were retransmitted
to prove that progress is due to original transmissions. Only then
keep FLAG_ORIG_SACK_ACKED set, allowing FRTO undo to proceed in
non-SACK case.
(FLAG_ORIG_SACK_ACKED is planned to be renamed to FLAG_ORIG_PROGRESS
to better indicate its purpose but to keep this change minimal, it
will be done in another patch).
Besides burstiness and congestion control violations, this problem
can result in RTO loop: When the loss recovery is prematurely
undoed, only new data will be transmitted (if available) and
the next retransmission can occur only after a new RTO which in case
of multiple losses (that are not for consecutive packets) requires
one RTO per loss to recover.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sk_rmem_alloc is larger than the receive buffer and we can't
schedule more memory for it, the skb will be dropped.
In above situation, if this skb is put into the ofo queue,
LINUX_MIB_TCPOFODROP is incremented to track it.
While if this skb is put into the receive queue, there's no record.
So a new SNMP counter is introduced to track this behavior.
LINUX_MIB_TCPRCVQDROP: Number of packets meant to be queued in rcv queue
but dropped because socket rcvbuf limit hit.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fast Open key could be stored in different endian based on the CPU.
Previously hosts in different endianness in a server farm using
the same key config (sysctl value) would produce different cookies.
This patch fixes it by always storing it as little endian to keep
same API for LE hosts.
Reported-by: Daniele Iamartino <danielei@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the tunnel option type stored in tunnel flags when creating options
for tunnels. Thereby ensuring we do not set geneve, vxlan or erspan tunnel
options on interfaces that are not associated with them.
Make sure all users of the infrastructure set correct flags, for the BPF
helper we have to set all bits to keep backward compatibility.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
