While https was always supported on linuxtv.org, only in
Dec 3 2015 the website is using valid certificates.
As we're planning to drop pure http support on some
future, change all references at the media subsystem
to point to the https URL instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Without I get this error for by dvb-card:
tda10071: Unknown symbol devm_regmap_init_i2c (err 0)
cx23885_dvb_register() dvb_register failed err = -22
cx23885_dev_setup() Failed to register dvb adapters on VID_B
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It works only for HVR-4400/HVR-5500.
For WinTV-HVR-930C-HD it fails with bad/no reception
for unknown reasons.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The current si2165_set_frontend() function actually works only for DVB-T.
Split it into two functions, preparing the code to support DVB-C.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use si2165_write_reg_list() to do the DVB-T mode initialization altogether.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
si2165_set_if_freq_shift() needs to call get_if_frequency() in order to do
the right shift. Add such logic inside the function, simplifying the logic
for the callers.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The TS config is fixed, so no need to write it for each tune.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Datasheet says they must be rewritten after reset.
But it only makes sense to write them when trying to tune afterwards.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is common the need of writing a table of values. Add a function to provide a
helper to address such case. This will allow further code cleanups.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is tricky to get rid of those ops here, as the stv0299 driver
wants to set frequency in separate from setting the bandwidth.
So, we use a small trick: we temporarely fill the cache with
0 for either frequency or bandwidth and add some logic at
set_params to only change the property(ies) that aren't zero.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those ops aren't used by any driver, with is weird. I suspect
that mantis_vb3030 driver were not working properly...
Anyway, now that the driver uses the set_parms, the DVB
frontend core should do the right thing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those callbacks are meant to be used only on some very specific
cases. There's absolutely no need to do that at tda8261, as
the only parameter that it allows to be set/get is the frequency.
So, use the standard get_params() and get_frequency() kABI
ops.
There's no need to touch at any bridge driver, as all interactions
are done via the macros at tda8261_cfg.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those two callbacks are the ones that should be used by normal
DVB frontend drivers.
Add support for them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On tda665x, set_state only sets frequency. As the kABI for set_state
is meant to be used only on special cases, split the function
into two, in order to allow it to be latter used by a DVBv5
cache params logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The stb6100 driver has a struct tuner_state on its state
struct, that it is used only to store the bandwidth. Even so,
this struct is not really used, as every time the bandwidth
is get or set, it goes through the hardware.
So, get rid of that.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are several tuner_param values that aren't by any driver or core:
DVBFE_TUNER_TUNERSTEP
DVBFE_TUNER_IFFREQ
DVBFE_TUNER_REFCLOCK
DVBFE_TUNER_IQSENSE
DVBFE_TUNER_DUMMY
Several of those correspond to the values at the tuner_state
struct with is also only initialized by not used anyware:
u32 tunerstep;
u32 ifreq;
u32 refclock;
It doesn't make sense to keep anything at the kABI that it is
not used. So, get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sR0p
-----END PGP SIGNATURE-----
Merge tag 'media/v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Media updates, including:
- Lots of improvements at the kABI documentation
- Split of Videobuf2 into a common part and a V4L2 specific one
- Split of the VB2 tracing events into a separate header file
- s5p-mfc got support for Exynos 5433
- v4l2 fixes for 64-bits alignment when running 32 bits userspace
on ARM
- Added support for SDR radio transmitter at core, vivid and hackrf
drivers
- Some y2038 fixups
- Some improvements at V4L2 colorspace support
- saa7164 converted to use the V4L2 core control framework
- several new boards additions, cleanups and fixups
PS: There are two patches for scripts/kernel-doc that are needed by
the documentation patches on Media. Jon is OK on merging those via
my tree"
* tag 'media/v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (146 commits)
[media] c8sectpfe: Remove select on CONFIG_FW_LOADER_USER_HELPER_FALLBACK
[media] DocBook media: update copyright/version numbers
[media] ivtv: Convert to get_user_pages_unlocked()
[media] media/v4l2-ctrls: fix setting autocluster to manual with VIDIOC_S_CTRL
[media] DocBook media: Fix a typo in encoder cmd
[media] DocBook: add SDR specific info to G_MODULATOR / S_MODULATOR
[media] DocBook: add SDR specific info to G_TUNER / S_TUNER
[media] hackrf: do not set human readable name for formats
[media] hackrf: add support for transmitter
[media] hackrf: switch to single function which configures everything
[media] hackrf: add control for RF amplifier
[media] DocBook: add modulator type field
[media] v4l: add type field to v4l2_modulator struct
[media] DocBook: document SDR transmitter
[media] v4l2: add support for SDR transmitter
[media] DocBook: document tuner RF gain control
[media] v4l2: add RF gain control
[media] v4l2: rename V4L2_TUNER_ADC to V4L2_TUNER_SDR
[media] media/vivid-osd: fix info leak in ioctl
[media] media: videobuf2: Move v4l2-specific stuff to videobuf2-v4l2
...
Device stopped to tuning some channels after regmap conversion.
Reason is that regmap_update_bits() works a bit differently for
partially volatile registers than old homemade routine. Return
back to old routine in order to fix issue.
Fixes: 478932b160
Cc: <stable@kernel.org> # 4.2+
Reported-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Tested-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When reading the firmware and sending commands, the length must
be bounds checked to avoid overrunning the size of the command
buffer and smashing the stack if the firmware is not in the expected
format:
si2168 11-0064: found a 'Silicon Labs Si2168-B40'
si2168 11-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 11-0064: firmware download failed -95
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: ffffffffa085708f
Add the proper check.
Cc: stable@kernel.org
Reported-by: Stuart Auchterlonie <sauchter@redhat.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If CONFIG_DVB_LNBH25 is disabled, a stub static inline function is
defined that just prints a warning about the driver being disabled
but the function return type was wrong which caused a build error.
Fixes: e025273b86 ("[media] lnbh25: LNBH25 SEC controller driver")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
If CONFIG_DVB_HORUS3A is disabled a stub static inline function is
defined that just prints a warning about the driver being disabled
but the function parameters were wrong which caused a build error.
Fixes: a5d32b3582 ("[media] horus3a: Sony Horus3A DVB-S/S2 tuner driver")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Replace struct v4l2_format * with void * to make queue_setup()
for common use.
And then, modify all device drivers related with this change.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix missing const in fimc-lite.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This saves a little .text and removes the sizeof(...) style
inconsistency. Use sizeof(*state) in accordance with CodingStyle.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove v4l2 stuff - v4l2_buf, v4l2_plane - from struct vb2_buffer.
Add new member variables - bytesused, length, offset, userptr, fd,
data_offset - to struct vb2_plane in order to cover all information
of v4l2_plane.
struct vb2_plane {
<snip>
unsigned int bytesused;
unsigned int length;
union {
unsigned int offset;
unsigned long userptr;
int fd;
} m;
unsigned int data_offset;
}
Replace v4l2_buf with new member variables - index, type, memory - which
are common fields for buffer management.
struct vb2_buffer {
<snip>
unsigned int index;
unsigned int type;
unsigned int memory;
unsigned int num_planes;
struct vb2_plane planes[VIDEO_MAX_PLANES];
<snip>
};
v4l2 specific fields - flags, field, timestamp, timecode,
sequence - are moved to vb2_v4l2_buffer in videobuf2-v4l2.c
struct vb2_v4l2_buffer {
struct vb2_buffer vb2_buf;
__u32 flags;
__u32 field;
struct timeval timestamp;
struct v4l2_timecode timecode;
__u32 sequence;
};
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cIed
-----END PGP SIGNATURE-----
Merge tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new DVB frontend drivers: ascot2e, cxd2841er, horus3a, lnbh25
- new HDMI capture driver: tc358743
- new driver for NetUP DVB new boards (netup_unidvb)
- IR support for DVBSky cards (smipcie-ir)
- Coda driver has gain macroblock tiling support
- Renesas R-Car gains JPEG codec driver
- new DVB platform driver for STi boards: c8sectpfe
- added documentation for the media core kABI to device-drivers DocBook
- lots of driver fixups, cleanups and improvements
* tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (297 commits)
[media] c8sectpfe: Remove select on undefined LIBELF_32
[media] i2c: fix platform_no_drv_owner.cocci warnings
[media] cx231xx: Use wake_up_interruptible() instead of wake_up_interruptible_nr()
[media] tc358743: only queue subdev notifications if devnode is set
[media] tc358743: add missing Kconfig dependency/select
[media] c8sectpfe: Use %pad to print 'dma_addr_t'
[media] DocBook media: Fix typo "the the" in xml files
[media] tc358743: make reset gpio optional
[media] tc358743: set direction of reset gpio using devm_gpiod_get
[media] dvbdev: document most of the functions/data structs
[media] dvb_frontend.h: document the struct dvb_frontend
[media] dvb-frontend.h: document struct dtv_frontend_properties
[media] dvb-frontend.h: document struct dvb_frontend_ops
[media] dvb: Use DVBFE_ALGO_HW where applicable
[media] dvb_frontend.h: document struct analog_demod_ops
[media] dvb_frontend.h: Document struct dvb_tuner_ops
[media] Docbook: Document struct analog_parameters
[media] dvb_frontend.h: get rid of dvbfe_modcod
[media] add documentation for struct dvb_tuner_info
[media] dvb_frontend: document dvb_frontend_tune_settings
...
The dvb_frontend.c core defines a FE_ALGO_HW symbol that it is
never used. Also, both cx24123 returns 1 to get_algo() callback
instead of using DVBFE_ALGO_HW.
Probably, those are some left overs from some code cleanup.
Let's stop returning magic numbers and use the proper macro
value.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Shut up this compiler warning that I get during the daily build:
horus3a.c: In function 'horus3a_set_params':
horus3a.c:308:24: warning: 'rolloff' may be used uninitialized in this function [-Wmaybe-uninitialized]
symbol_rate * (100 + rolloff), 200000) + 5;
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert the struct dvb_pll_desc uses to const and
change the "entries" fixed array size from 12 to []
It saves a couple KB overall and remove ~5KB of data.
$ size drivers/media/dvb-frontends/dvb-pll.o*
text data bss dec hex filename
8520 1552 2120 12192 2fa0 drivers/media/dvb-frontends/dvb-pll.o.new
5624 6363 2120 14107 371b drivers/media/dvb-frontends/dvb-pll.o.old
[PG] Patch taken from https://lkml.org/lkml/2015/6/24/721 with
commit message updated.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Michael Ira Krufky <m.krufky@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The B2100A dvb NIM card from ST has 2x stv0367 demodulators
and 2x TDA18212 silicon tuners, with a 16Mhz crystal. To
get this working properly with the upstream driver we need
to add support for the 16Mhz reference clock.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When using stv0367 demodulator with STi STB platforms,
we can have easily have four or more stv0367 demods running
in the system at one time.
As typically the b2120 reference design ships with a b2004a daughter
board, which can accept two dvb NIM cards, and each b2100A NIM
has 2x stv0367 demods and 2x NXPs tuner on it.
In such circumstances it is useful to print the i2c address
on error messages to know which one is failing due to I2C issues.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Linux stack is short; we need to be able to count the number
of bytes used at stack on each function. So, we don't like to
use variable-length arrays, as complained by smatch:
drivers/media/dvb-frontends/horus3a.c:57:19: warning: Variable length array is used.
The max usecase of the driver seems to be 10 bytes + 1 for the
register.
So, let's be safe and allocate 11 bytes for the write buffer.
This should be enough to cover all cases. If not, let's print
an error message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Linux stack is short; we need to be able to count the number
of bytes used at stack on each function. So, we don't like to
use variable-length arrays, as complained by smatch:
drivers/media/dvb-frontends/horus3a.c:57:19: warning: Variable length array is used.
The max usecase of the driver seems to be 5 bytes + 1 for the
register.
So, let's be safe and allocate 6 bytes for the write buffer.
This should be enough to cover all cases. If not, let's print
an error message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Linux stack is short; we need to be able to count the number
of bytes used at stack on each function. So, we don't like to
use variable-length arrays, as complained by smatch:
drivers/media/dvb-frontends/cxd2841er.c:205:19: warning: Variable length array is used.
The max usecase of the driver seems to be 15 bytes + 1 for the
register.
So, let's be safe and allocate 17 bytes for the write buffer.
This should be enough to cover all cases. If not, let's print
an error message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/cxd2841er.c:992:5: warning: no previous prototype for 'cxd2841er_get_carrier_offset_t2' [-Wmissing-prototypes]
int cxd2841er_get_carrier_offset_t2(
^
drivers/media/dvb-frontends/cxd2841er.c:1032:5: warning: no previous prototype for 'cxd2841er_get_carrier_offset_c' [-Wmissing-prototypes]
int cxd2841er_get_carrier_offset_c(
^
drivers/media/dvb-frontends/cxd2841er.c:1360:5: warning: no previous prototype for 'cxd2841er_read_snr_t2' [-Wmissing-prototypes]
int cxd2841er_read_snr_t2(struct cxd2841er_priv *priv, u32 *snr)
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add DVB SEC frontend driver for STM LNBH25PQR chip.
[mchehab@osg.samsung.com: fix merge conflict:
fe_sec_voltage_t should not be used in kernelspace anymore.
instead, it should use enum fe_sec_voltage]
Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the DVB Frontends menu visible when compile-testing, to allow
selecting additional drivers on top of the drivers that are already
automatically selected if MEDIA_SUBDRV_AUTOSELECT is enabled.
Without this, many drivers stay disabled during e.g. allmodconfig.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement DVBv5 CNR, signal strength, BER and block errors.
Wrap legacy DVBv3 statistics to DVBv5 internally.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is a bit hack, but returning error when driver is not tuned yet
causes DVBv5 zap stop polling DVBv5 statistics. Thus return 0 even
callback is called during invalid device state.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There should be clearly some lock in order to make sure firmware
command in execution is not disturbed by another command. It has
worked as callbacks are serialized somehow pretty well and command
execution happens usually without any delays.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
