When building building AMSDU from non-linear SKB, we hit a
kernel panic when trying to push the padding to the tail.
Instead, put the padding at the head of the next subframe.
This also fixes the A-MSDU subframes to not have the padding
accounted in the length field and not have pad at all for
the last subframe, both required by the spec.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Reviewed-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE 802.11-2016 14.10.8.3 HWMP sequence numbering says:
If it is a target mesh STA, it shall update its own HWMP SN to
maximum (current HWMP SN, target HWMP SN in the PREQ element) + 1
immediately before it generates a PREP element in response to a
PREQ element.
Signed-off-by: Yuan-Chi Pang <fu3mo6goo@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes:
[BUG] gpio: gpio-adp5588: A possible sleep-in-atomic-context bug
in adp5588_gpio_write()
[BUG] gpio: gpio-adp5588: A possible sleep-in-atomic-context bug
in adp5588_gpio_direction_input()
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While recently going over bpf_msg_pull_data(), I noticed three
issues which are fixed in here:
1) When we attempt to find the first scatterlist element (sge)
for the start offset, we add len to the offset before we check
for start < offset + len, whereas it should come after when
we iterate to the next sge to accumulate the offsets. For
example, given a start offset of 12 with a sge length of 8
for the first sge in the list would lead us to determine this
sge as the first sge thinking it covers first 16 bytes where
start is located, whereas start sits in subsequent sges so
we would end up pulling in the wrong data.
2) After figuring out the starting sge, we have a short-cut test
in !msg->sg_copy[i] && bytes <= len. This checks whether it's
not needed to make the page at the sge private where we can
just exit by updating msg->data and msg->data_end. However,
the length test is not fully correct. bytes <= len checks
whether the requested bytes (end - start offsets) fit into the
sge's length. The part that is missing is that start must not
be sge length aligned. Meaning, the start offset into the sge
needs to be accounted as well on top of the requested bytes
as otherwise we can access the sge out of bounds. For example
the sge could have length of 8, our requested bytes could have
length of 8, but at a start offset of 4, so we also would need
to pull in 4 bytes of the next sge, when we jump to the out
label we do set msg->data to sg_virt(&sg[i]) + start - offset
and msg->data_end to msg->data + bytes which would be oob.
3) The subsequent bytes < copy test for finding the last sge has
the same issue as in point 2) but also it tests for less than
rather than less or equal to. Meaning if the sge length is of
8 and requested bytes of 8 while having the start aligned with
the sge, we would unnecessarily go and pull in the next sge as
well to make it private.
Fixes: 015632bb30 ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull thermal fixes from Eduardo Valentin:
"Minor fixes to OF thermal, qoriq, and rcar drivers"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: of-thermal: disable passive polling when thermal zone is disabled
thermal: rcar_gen3_thermal: convert to SPDX identifiers
thermal: rcar_thermal: convert to SPDX identifiers
thermal: qoriq: Switch to SPDX identifier
thermal: qoriq: Simplify the 'site' variable assignment
thermal: qoriq: Use devm_thermal_zone_of_sensor_register()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count,
GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
Notice that, currently, there is a bug during the allocation:
sizeof(npcm7xx_clk_data) should be sizeof(*npcm7xx_clk_data)
Fix this bug by using struct_size() in kzalloc()
This issue was detected with the help of Coccinelle.
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Avi Fishman <avifishman70@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Variable save_pud is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
variable 'save_pud' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Export device state to sysfs to allow for easier get device state.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Thanks to Christoph Hellwig for pointing out a cleaner way to do this,
as my approach was quite ugly.
CC: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
As of commit fd1102f0aa ("mm: mmu_notifier fix for tlb_end_vma"),
asm-generic/tlb.h now calls tlb_flush() from a static inline function,
so we need to make sure that it's declared before #including the
asm-generic header in the arch header.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: fd1102f0aa ("mm: mmu_notifier fix for tlb_end_vma")
Signed-off-by: Will Deacon <will.deacon@arm.com>
[groeck: Use forward declaration instead of moving inline function]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
I managed to miss one of Rob's code reviews on the mailing list
<http://lists.infradead.org/pipermail/linux-riscv/2018-August/001139.html>.
The patch has already been merged, so I'm submitting a fixup.
Sorry!
Fixes: b67bc7cb40 ("dt-bindings: interrupt-controller: RISC-V local interrupt controller")
Cc: Rob Herring <robh@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Karsten Merker <merker@debian.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
We use kzalloc to allocate the write_buf that we use for
i2c transfer on hdcp write. But it seems that we are forgetting
to free the memory that is not needed after i2c transfer is
completed.
Reported-by: Brian J Wood <brian.j.wood@intel.com>
Fixes: 2320175feb ("drm/i915: Implement HDCP for HDMI")
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180823205136.31310-1-rodrigo.vivi@intel.com
(cherry picked from commit 62d3a8deaa)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The workaround was supposed to look at the plane destination
coordinates. Currently it's looking at some mixture of src
and dst coordinates that doesn't make sense. Fix it up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180719182214.4323-2-ville.syrjala@linux.intel.com
Fixes: 394676f05b (drm/i915: Add WA for planes ending close to left screen edge)
Reviewed-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit b1f1c2c11f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Fix the VMC page fault when the running sequence is as below:
1.amdgpu_gem_create_ioctl
2.ttm_bo_swapout->amdgpu_vm_bo_invalidate, as not called
amdgpu_vm_bo_base_init, so won't called
list_add_tail(&base->bo_list, &bo->va). Even the bo was evicted,
it won't set the bo_base->moved.
3.drm_gem_open_ioctl->amdgpu_vm_bo_base_init, here only called
list_move_tail(&base->vm_status, &vm->evicted), but not set the
bo_base->moved.
4.amdgpu_vm_bo_map->amdgpu_vm_bo_insert_map, as the bo_base->moved is
not set true, the function amdgpu_vm_bo_insert_map will call
list_move(&bo_va->base.vm_status, &vm->moved)
5.amdgpu_cs_ioctl won't validate the swapout bo, as it is only in the
moved list, not in the evict list. So VMC page fault occurs.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise we can get the following errors occasionally on some devices:
mmc1: tried to HW reset card, got error -110
mmcblk1: error -110 requesting status
mmcblk1: recovery failed!
print_req_error: I/O error, dev mmcblk1, sector 14329
...
I have one device that hits this error almost on every boot, and another
one that hits it only rarely with the other ones I've used behave without
problems. I'm not sure if the issue is related to a particular eMMC card
model, but in case it is, both of the machines with issues have:
# cat /sys/class/mmc_host/mmc1/mmc1:0001/manfid \
/sys/class/mmc_host/mmc1/mmc1:0001/oemid \
/sys/class/mmc_host/mmc1/mmc1:0001/name
0x000045
0x0100
SEM16G
and the working ones have:
0x000011
0x0100
016G92
Note that "ti,non-removable" is different as omap_hsmmc_reg_get() does not
call omap_hsmmc_disable_boot_regulators() if no_regulator_off_init is set.
And currently we set no_regulator_off_init only for "ti,non-removable" and
not for "non-removable". It seems that we should have "non-removable" with
some other mmc generic property behave in the same way instead of having to
use a non-generic property. But let's fix the issue first.
Fixes: 7e2f8c0ae6 ("ARM: dts: Add minimal support for motorola droid 4
xt894")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix wrong mode for dts file added by commit bb3e3fbbac
("ARM: dts: Add DT support for Octavo Systems OSD3358-SM-RED
based on TI AM335x").
Signed-off-by: Neeraj Dantu <neeraj.dantu@octavosystems.com>
CC: Robert Nelson <robertcnelson@gmail.com>
CC: Jason Kridner <jkridner@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
freq_reg_info expects to get the frequency in kHz. Instead we
accidently pass it in MHz. Thus, currently the function always
return ERR rule. Fix that.
Fixes: 50f32718e1 ("nl80211: Add wmm rule attribute to NL80211_CMD_GET_WIPHY dump command")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[fix kHz/MHz in commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TXOP (also known as Channel Occupancy Time) is u16 and should be
added using nla_put_u16 instead of u8, fix that.
Fixes: 50f32718e1 ("nl80211: Add wmm rule attribute to NL80211_CMD_GET_WIPHY dump command")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
User controls @idx which to be used as index of hwsim_world_regdom_custom.
So, It can be exploited via Spectre-like attack. (speculative execution)
This kind of attack leaks address of hwsim_world_regdom_custom,
It leads an attacker to bypass security mechanism such as KASLR.
So sanitize @idx before using it to prevent attack.
I leveraged strategy [1] to find and exploit this gadget.
[1] https://github.com/jinb-park/linux-exploit/tree/master/exploit-remaining-spectre-gadget/
Signed-off-by: Jinbum Park <jinb.park7@gmail.com>
[johannes: unwrap URL]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I changed the way mac80211 updates the PM state of the peer.
I forgot that we could also have multicast frames from the
peer and that those frame should of course not change the
PM state of the peer: A peer goes to power save when it
needs to scan, but it won't send the broadcast Probe Request
with the PM bit set.
This made us mark the peer as awake when it wasn't and then
Intel's firmware would fail to transmit because the peer is
asleep according to its database. The driver warned about
this and it looked like this:
WARNING: CPU: 0 PID: 184 at /usr/src/linux-4.16.14/drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1369 iwl_mvm_rx_tx_cmd+0x53b/0x860
CPU: 0 PID: 184 Comm: irq/124-iwlwifi Not tainted 4.16.14 #1
RIP: 0010:iwl_mvm_rx_tx_cmd+0x53b/0x860
Call Trace:
iwl_pcie_rx_handle+0x220/0x880
iwl_pcie_irq_handler+0x6c9/0xa20
? irq_forced_thread_fn+0x60/0x60
? irq_thread_dtor+0x90/0x90
The relevant code that spits the WARNING is:
case TX_STATUS_FAIL_DEST_PS:
/* the FW should have stopped the queue and not
* return this status
*/
WARN_ON(1);
info->flags |= IEEE80211_TX_STAT_TX_FILTERED;
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=199967.
Fixes: 9fef654433 ("mac80211: always update the PM state of a peer on MGMT / DATA frames")
Cc: <stable@vger.kernel.org> #4.16+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make wmm_rule be part of the reg_rule structure. This simplifies the
code a lot at the cost of having bigger memory usage. However in most
cases we have only few reg_rule's and when we do have many like in
iwlwifi we do not save memory as it allocates a separate wmm_rule for
each channel anyway.
This also fixes a bug reported in various places where somewhere the
pointers were corrupted and we ended up doing a null-dereference.
Fixes: 230ebaa189 ("cfg80211: read wmm rules from regulatory database")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
[rephrase commit message slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mac80211_hwsim driver intends to say that it supports up to four
STBC receive streams, but instead it ends up saying something undefined.
The IEEE80211_VHT_CAP_RXSTBC_X macros aren't independent bits that can
be ORed together, but values. In this case, _4 is the appropriate one
to use.
Signed-off-by: Danek Duvall <duvall@comfychair.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mod mask for VHT capabilities intends to say that you can override
the number of STBC receive streams, and it does, but only by accident.
The IEEE80211_VHT_CAP_RXSTBC_X aren't bits to be set, but values (albeit
left-shifted). ORing the bits together gets the right answer, but we
should use the _MASK macro here instead.
Signed-off-by: Danek Duvall <duvall@comfychair.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, when a redirect occurs in sockmap and an error occurs in
the redirect call we unwind the scatterlist once in the error path
of bpf_tcp_sendmsg_do_redirect() and then again in sendmsg(). Then
in the error path of sendmsg we decrement the copied count by the
send size.
However, its possible we partially sent data before the error was
generated. This can happen if do_tcp_sendpages() partially sends the
scatterlist before encountering a memory pressure error. If this
happens we need to decrement the copied value (the value tracking
how many bytes were actually sent to TCP stack) by the number of
remaining bytes _not_ the entire send size. Otherwise we risk
confusing userspace.
Also we don't need two calls to free the scatterlist one is
good enough. So remove the one in bpf_tcp_sendmsg_do_redirect() and
then properly reduce copied by the number of remaining bytes which
may in fact be the entire send size if no bytes were sent.
To do this use bool to indicate if free_start_sg() should do mem
accounting or not.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When a targetport is removed from the config, fcloop will avoid calling
the LS done() routine thinking the targetport is gone. This leaves the
initiator reset/reconnect hanging as it waits for a status on the
Create_Association LS for the reconnect.
Change the filter in the LS callback path. If tport null (set when
failed validation before "sending to remote port"), be sure to call
done. This was the main bug. But, continue the logic that only calls
done if tport was set but there is no remoteport (e.g. case where
remoteport has been removed, thus host doesn't expect a completion).
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In many architectures loads may be reordered with older stores to
different locations. In the nvme driver the following two operations
could be reordered:
- Write shadow doorbell (dbbuf_db) into memory.
- Read EventIdx (dbbuf_ei) from memory.
This can result in a potential race condition between driver and VM host
processing requests (if given virtual NVMe controller has a support for
shadow doorbell). If that occurs, then the NVMe controller may decide to
wait for MMIO doorbell from guest operating system, and guest driver may
decide not to issue MMIO doorbell on any of subsequent commands.
This issue is purely timing-dependent one, so there is no easy way to
reproduce it. Currently the easiest known approach is to run "Oracle IO
Numbers" (orion) that is shipped with Oracle DB:
orion -run advanced -num_large 0 -size_small 8 -type rand -simulate \
concat -write 40 -duration 120 -matrix row -testname nvme_test
Where nvme_test is a .lun file that contains a list of NVMe block
devices to run test against. Limiting number of vCPUs assigned to given
VM instance seems to increase chances for this bug to occur. On test
environment with VM that got 4 NVMe drives and 1 vCPU assigned the
virtual NVMe controller hang could be observed within 10-20 minutes.
That correspond to about 400-500k IO operations processed (or about
100GB of IO read/writes).
Orion tool was used as a validation and set to run in a loop for 36
hours (equivalent of pushing 550M IO operations). No issues were
observed. That suggest that the patch fixes the issue.
Fixes: f9f38e3338 ("nvme: improve performance for virtual NVMe devices")
Signed-off-by: Michal Wnukowski <wnukowski@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
[hch: updated changelog and comment a bit]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Building the newly introduced BPF_PROG_TYPE_SK_REUSEPORT leads to
a compile time error when building with clang:
net/core/filter.o: In function `sk_reuseport_convert_ctx_access':
../net/core/filter.c:7284: undefined reference to `__compiletime_assert_7284'
It seems that clang has issues resolving hweight_long at compile
time. Since SK_FL_PROTO_MASK is a constant, we can use the interface
for known constant arguments which works fine with clang.
Fixes: 2dbb9b9e6d ("bpf: Introduce BPF_PROG_TYPE_SK_REUSEPORT")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In bpf_tcp_recvmsg() we first took a reference on the psock, however
once we find that there are skbs in the normal socket's receive queue
we return with processing them through tcp_recvmsg(). Problem is that
we leak the taken reference on the psock in that path. Given we don't
really do anything with the psock at this point, move the skb_queue_empty()
test before we fetch the psock to fix this case.
Fixes: 8934ce2fd0 ("bpf: sockmap redirect ingress support")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
bpf_tcp_close() we pop the psock linkage to a map via psock_map_pop().
A parallel update on the sock hash map can happen between psock_map_pop()
and lookup_elem_raw() where we override the element under link->hash /
link->key. In bpf_tcp_close()'s lookup_elem_raw() we subsequently only
test whether an element is present, but we do not test whether the
element is infact the element we were looking for.
We lock the sock in bpf_tcp_close() during that time, so do we hold
the lock in sock_hash_update_elem(). However, the latter locks the
sock which is newly updated, not the one we're purging from the hash
table. This means that while one CPU is doing the lookup from bpf_tcp_close(),
another CPU is doing the map update in parallel, dropped our sock from
the hlist and released the psock.
Subsequently the first CPU will find the new sock and attempts to drop
and release the old sock yet another time. Fix is that we need to check
the elements for a match after lookup, similar as we do in the sock map.
Note that the hash tab elems are freed via RCU, so access to their
link->hash / link->key is fine since we're under RCU read side there.
Fixes: e9db4ef6bf ("bpf: sockhash fix omitted bucket lock in sock_close")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Currently, variable ref_count within the bsg_device struct is of
type atomic_t. For variables being used as reference counters,
the refcount API should be used instead of atomic. The newer
refcount API works to prevent counter overflows and use-after-free
bugs. So, move this varable from the atomic API to refcount,
potentially avoiding the issues mentioned.
Signed-off-by: John Pittman <jpittman@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
kmem_cache_destroy() can handle NULL pointer correctly, so there is
no need to check e->icq_cache before calling kmem_cache_destroy().
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In IPv4, the newly introduced rdma_read_gids is used to read the SGID/DGID
for the connection which returns GID correctly for RoCE transport as well.
In IPv6, rdma_read_gids is also used. The following are why rdma_read_gids
is introduced.
rdma_addr_get_dgid() for RoCE for client side connections returns MAC
address, instead of DGID.
rdma_addr_get_sgid() for RoCE doesn't return correct SGID for IPv6 and
when more than one IP address is assigned to the netdevice.
So the transport agnostic rdma_read_gids() API is provided by rdma_cm
module.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 52638f71fc ("dsa: Move gpio reset into switch driver")
moved the GPIO handling into the switch drivers but forgot
to remove the GPIO header includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function tipc_dest_push, the 32bit variables 'node' and 'port'
are stored separately in uppper and lower part of 64bit 'value'.
Then this value is assigned to dst->value which is a union like:
union
{
struct {
u32 port;
u32 node;
};
u64 value;
}
This works on little-endian machines like x86 but fails on big-endian
machines.
The fix remove the 'value' stack parameter and even the 'value'
member of the union in tipc_dest, assign the 'node' and 'port' member
directly with the input parameter to avoid the endian issue.
Fixes: a80ae5306a ("tipc: improve destination linked list")
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Haiqing Bai <Haiqing.Bai@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
net: sched: couple of small fixes
Jiri Pirko (2):
net: sched: fix extack error message when chain is failed to be
created
net: sched: return -ENOENT when trying to remove filter from
non-existent chain
====================
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When chain 0 was implicitly created, removal of non-existent filter from
chain 0 gave -ENOENT. Once chain 0 became non-implicit, the same call is
giving -EINVAL. Fix this by returning -ENOENT in that case.
Reported-by: Roman Mashak <mrv@mojatatu.com>
Fixes: f71e0ca4db ("net: sched: Avoid implicit chain 0 creation")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After erspan_ver is introudced, if erspan_ver is not set in iproute, its
value will be left 0 by default. Since Commit 02f99df187 ("erspan: fix
invalid erspan version."), it has broken the traffic due to the version
check in erspan_xmit if users are not aware of 'erspan_ver' param, like
using an old version of iproute.
To fix this compatibility problem, it sets erspan_ver to 1 by default
when adding an erspan dev in erspan_setup. Note that we can't do it in
ipgre_netlink_parms, as this function is also used by ipgre_changelink.
Fixes: 02f99df187 ("erspan: fix invalid erspan version.")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After changing rhashtable_walk_start to return void, start_fail would
never be set other value than 0, and the checking for start_fail is
pointless, so remove it.
Fixes: 97a6ec4ac0 ("rhashtable: Change rhashtable_walk_start to return void")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Marcelo noticed, in sctp_transport_get_next, it is iterating over
transports but then also accessing the association directly, without
checking any refcnts before that, which can cause an use-after-free
Read.
So fix it by holding transport before accessing the association. With
that, sctp_transport_hold calls can be removed in the later places.
Fixes: 626d16f50f ("sctp: export some apis or variables for sctp_diag and reuse some for proc")
Reported-by: syzbot+fe62a0c9aa6a85c6de16@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA is broken on this specific device for some unknown
reason (probably badly designed or plain broken interface
electronics) and will only work with PIO. Other users of
the same hardware does not have this problem.
Add a specific quirk so that this Gemini device gets
DMA turned off. Also fix up some code around passing the
port information around in probe while we're at it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
when ac/dc switch, driver will be notified by acpi event.
then the power source will be updated. so don't need to
get power source when set power state.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is currently an intermittent hang from a memory leak in
DTN stress testing. It is caused by unfreed memory during driver
disable.
[How]
Do a dc_sink_release in the case that skips it incorrectly.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can't hold the mn_lock while allocating memory.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
when hw_fini/suspend, smu only need to power on uvd block
if uvd pg is supported, don't need to call uvd to do hw_init.
v2: fix typo in patch descriptions and comments.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For SI/Kv, the power state is managed by function
amdgpu_pm_compute_clocks.
when dpm enabled, we should call amdgpu_pm_compute_clocks
to update current power state instand of set boot state.
this change can fix the oops when kfd driver was enabled on Kv.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Forgot to add vce pg support via smu for Kaveri/Mullins.
Fixes: 561a5c83eadd ("drm/amd/pp: Unify powergate_uvd/vce/mmhub
to set_powergating_by_smu")
v2: refine patch descriptions suggested by Michel
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is required by gfx hw and can fix the rlc hang when
do s3 stree test on Cz/St.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Hang Zhou <hang.zhou@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
