Keep track of the als and px enabled/disabled status in
order to enable them selectively.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This chip supports two power modes.
1. "one-shot" mode - the chip activates and executes one complete
conversion loop and then shuts itself down. This is the default mode
chosen for raw reads.
2. "continuous" mode - the chip takes continuous measurements.
Continuous mode is more expensive power-wise but may be more reliable.
Add a property so that if preferred, the default power mode for raw
reads can be set to continuous.
Separate one-shot enabling in a separate function that will be used
depending on the chosen power mode. Also create a function for
powering the chip on and off.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The mcp3421 is the single channel variant of the mcp342x family. Support
is straight forward, only the channels array has to be added for this
chip.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for the touchscreen on Samsung s3c64xx.
The driver is completely untested but shows roughly how
it could be done, following the example of the at91 driver.
compared to the old plat-samsung/adc driver, there is
no support for prioritizing ts over other clients, nor
for oversampling. From my reading of the code, the
priorities didn't actually have any effect at all, but
the oversampling might be needed.
Verifying this driver is the main issue that is currently
holding up multiplatform support for s3c64xx, so any help
in testing is very much appreciated.
The current version uses the IS_REACHABLE() that is
going to be introduced in the linux-media tree, please
comment this out for testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Usual mixed bag, but the big item perhaps in this series is the DMA buffer
support added by Lars-Peter Clausen. It's been in the works for a long time
and it will be interesting to see what hardware support shows up now that
this is available.
New core features + associate cleanup.
* Add generic DMA buffer infrastructure
* Add a DMAengine framework based buffer
Also associated minor changes.
- Set the device buffer watermark based on the minimum watermark for all
attached buffers rather than just the 'primary' one.
- iio_buffer_init - only set the watermark default if one hasn't already
been provided. This allows simple support for devices with a fixed
watermark.
- read only attribute for watermark on fixed watermark devices.
- add explicit buffer enable/disable callbacks to allow the buffer to
do more than trivial actions when it is being turned on and off.
* IIO_VAL_INT support in write_raw_get_fmt function.
New device support
* Freescale MMA7455/7456L accelerometers
* Memsic MXC6255XC accelerometer
* ST lis2dh12 accelerometer
* TI ADS8688 ADC
* TI Palamas (twl6035/7) gpadc
New driver features
* mma8452
- support either of the available interrupt pins to cope with the case
where board layout has lead to a particular one being connected.
Staging graduation
* Dummy driver
- this driver acts as both an example and a test device for those with
out hardware to develop userspace code against.
Cleanups and minor bits and bobs.
* treewide
- Sort out the ordering of iio_device_register/unregister vs runtime
pm function calls so that it's all nice and consistent and not race
prone.
- Check sscanf return values. None of the cases will actually happen as
the strings are supplied internally, but best to be consistent on this.
* ad7780
- switch over to the gpio descriptor interface and remove the now unused
platform data which gets rid of a header entirely.
* ad7793
- drop a pointless else statement.
* at91_adc
- Swap kmalloc_array in for a kmalloc doing the same job.
* dummy
- get rid of some commented out lines that snuck in during the move of
the driver.
* lm3533-als
- Print an error message on provision of an invalid resistance.
* mcp320x
- Add compatible strings with vendor prefix and deprecate those with
no vendor prefix.
* mxs-lradc
- Use BIT macro in various places rather than shifted ones.
* pa12203001
- Power off the chip if the registration fails.
* pulsedlight-lidar-lite
- add runtime PM support.
* xilinx XADC
- constify an iio_buffer_setup_ops structure.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=CfCl
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 4.5 cycle
Usual mixed bag, but the big item perhaps in this series is the DMA buffer
support added by Lars-Peter Clausen. It's been in the works for a long time
and it will be interesting to see what hardware support shows up now that
this is available.
New core features + associate cleanup.
* Add generic DMA buffer infrastructure
* Add a DMAengine framework based buffer
Also associated minor changes.
- Set the device buffer watermark based on the minimum watermark for all
attached buffers rather than just the 'primary' one.
- iio_buffer_init - only set the watermark default if one hasn't already
been provided. This allows simple support for devices with a fixed
watermark.
- read only attribute for watermark on fixed watermark devices.
- add explicit buffer enable/disable callbacks to allow the buffer to
do more than trivial actions when it is being turned on and off.
* IIO_VAL_INT support in write_raw_get_fmt function.
New device support
* Freescale MMA7455/7456L accelerometers
* Memsic MXC6255XC accelerometer
* ST lis2dh12 accelerometer
* TI ADS8688 ADC
* TI Palamas (twl6035/7) gpadc
New driver features
* mma8452
- support either of the available interrupt pins to cope with the case
where board layout has lead to a particular one being connected.
Staging graduation
* Dummy driver
- this driver acts as both an example and a test device for those with
out hardware to develop userspace code against.
Cleanups and minor bits and bobs.
* treewide
- Sort out the ordering of iio_device_register/unregister vs runtime
pm function calls so that it's all nice and consistent and not race
prone.
- Check sscanf return values. None of the cases will actually happen as
the strings are supplied internally, but best to be consistent on this.
* ad7780
- switch over to the gpio descriptor interface and remove the now unused
platform data which gets rid of a header entirely.
* ad7793
- drop a pointless else statement.
* at91_adc
- Swap kmalloc_array in for a kmalloc doing the same job.
* dummy
- get rid of some commented out lines that snuck in during the move of
the driver.
* lm3533-als
- Print an error message on provision of an invalid resistance.
* mcp320x
- Add compatible strings with vendor prefix and deprecate those with
no vendor prefix.
* mxs-lradc
- Use BIT macro in various places rather than shifted ones.
* pa12203001
- Power off the chip if the registration fails.
* pulsedlight-lidar-lite
- add runtime PM support.
* xilinx XADC
- constify an iio_buffer_setup_ops structure.
Add runtime PM support for the lidar-lite module to enable low power
mode when last device requested reading is over a second.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
So this patch swaps that use out for kmalloc_array instead.
Signed-off-by Nizam Haider <nijamh@cdac.in>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
for_each_available_child_of_node performs an of_node_get on each iteration,
so a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
WARN_ON() only takes a condition argument. I have changed these to
WARN() instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add missing pm_runtime_mark_last_busy to apds9960_set_power_state
function.
Unless pm_runtime_mark_last_busy is called the
pm_runtime_put_autosuspend may put the device into suspend before the
delay time requested.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Returning zero from the measurment function has the side effect of
corrupting the triggered buffer readings, better to use -EINVAL than
a zero measurement reading.
The INVALID status happens even it isn't out of range
sometimes roughly once every second or two. This can be from an
invalid second signal return path. Hence there are spurious zero
readings from the triggered buffer, and warning messages in the kernel
log.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This set does not include those for issues introduced during the merge
window. Fixes of those will follow in a future series.
* ad5064
- Make sure the local i2c_write returns 0 on success rather than the
number of bytes transfered. Otherwise we report an error on all writes.
- Fix a shift for ad5629 and ad5669 which gives incorrect DAC output on
these parts.
* ad7793
- The product ID on the datasheet is wrong. Fix it in the driver.
* IIO_DUMMY_EVGEN
- select IRQ_WORK as a dependency.
* lpc32xx
- make sure clock is prepared before enabling.
* si7020
- data byte order was reversed. Fix it.
* vf610
- Internal temperature calculation was wrong if a different
reference voltage was used. Now use a linear interpolation
function to make it work over the full range.
- Fix a division by zero in the case of a device tree property
not being present (same issue two fixes).
* xilinx XADC
- VREFN scale was wrong - fix it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=362F
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.4a' of ssh://ra.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.4 cycle.
This set does not include those for issues introduced during the merge
window. Fixes of those will follow in a future series.
* ad5064
- Make sure the local i2c_write returns 0 on success rather than the
number of bytes transfered. Otherwise we report an error on all writes.
- Fix a shift for ad5629 and ad5669 which gives incorrect DAC output on
these parts.
* ad7793
- The product ID on the datasheet is wrong. Fix it in the driver.
* IIO_DUMMY_EVGEN
- select IRQ_WORK as a dependency.
* lpc32xx
- make sure clock is prepared before enabling.
* si7020
- data byte order was reversed. Fix it.
* vf610
- Internal temperature calculation was wrong if a different
reference voltage was used. Now use a linear interpolation
function to make it work over the full range.
- Fix a division by zero in the case of a device tree property
not being present (same issue two fixes).
* xilinx XADC
- VREFN scale was wrong - fix it.
The iio_buffer_setup_ops structures are never modified, so declare this one
as const, like the others.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The scaling factor for VREFN is 3.0/4096 (not 1.0/4096), just as for
VREFP. This is not immediately obvious from the specification (Xilinx
UG480), but has been confirmed by Xilinx support.
Suggested-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Silicon Labs Si7013, Si7020, and Si7021 family of I2C humidity and
temperature sensors deliver 16 bit data high byte first.
See the datasheet available at:
https://www.silabs.com/Support%20Documents%2fTechnicalDocs%2fSi7020-A20.pdf
But as documented in Documentation/i2c/smbus-protocol,
i2c_smbus_read_word_data() expects the low byte first.
Change the driver to use i2c_smbus_read_word_swapped to get correct byte
order.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for the Texas Intruments ADS8688 ADC.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Reviewed-by: Martin Hundebøll <martin.hundeboll@prevas.dk>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added core support for IIO_VAL_INT in write_raw_get_fmt function.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This commit add support for STMicroelectronics lis2dh12 accelerometer.
Datasheet for this device can be found here:
http://www.st.com/st-web-ui/static/active/en/resource/technical/
document/datasheet/DM00091513.pdf
Signed-off-by: Giuseppe Barba <giuseppe.barba@st.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fixes the following checkpatch warning:
WARNING: unchecked sscanf return value
Signed-off-by: Ioana Ciornei <ciorneiioana@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
At probe, runtime pm should be setup before registering the sysfs interface so
that all the power attributes are accurate and functional when registering.
Also, when removing the device we should unregister first to make sure
that the interfaces that may result in wakeups are no longer available.
Fix this behaviour for the following drivers: bmc150, bmg160, kmx61,
kxcj-1013, mma9551, mma9553, rpr0521.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Make sure we poweroff the chip if for any reason iio_register
returns an error.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
Add support for Freescale MMA7455L/MMA7456L 3-axis in 10-bit mode for
I2C and SPI bus. This rather simple driver that currently doesn't
support all the hardware features of MMA7455L/MMA7456L.
Tested on Embedded Artist's LPC4357 Dev Kit with MMA7455L on I2C bus.
Data sheets for the two devices can be found here:
http://cache.freescale.com/files/sensors/doc/data_sheet/MMA7455L.pdfhttp://cache.freescale.com/files/sensors/doc/data_sheet/MMA7456L.pdf
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Print an error message to indicate that invalid configuration data was
provided in the platform_data, rather than just aborting initialization.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a generic fully device independent DMA buffer implementation that uses
the DMAegnine framework to perform the DMA transfers. This can be used by
converter drivers that whish to provide a DMA buffer for converters that
are connected to a DMA core that implements the DMAengine API.
Apart from allocating the buffer using iio_dmaengine_buffer_alloc() and
freeing it using iio_dmaengine_buffer_free() no additional converter driver
specific code is required when using this DMA buffer implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The traditional approach used in IIO to implement buffered capture requires
the generation of at least one interrupt per sample. In the interrupt
handler the driver reads the sample from the device and copies it to a
software buffer. This approach has a rather large per sample overhead
associated with it. And while it works fine for samplerates in the range of
up to 1000 samples per second it starts to consume a rather large share of
the available CPU processing time once we go beyond that, this is
especially true on an embedded system with limited processing power. The
regular interrupt also causes increased power consumption by not allowing
the hardware into deeper sleep states, which is something that becomes more
and more important on mobile battery powered devices.
And while the recently added watermark support mitigates some of the issues
by allowing the device to generate interrupts at a rate lower than the data
output rate, this still requires a storage buffer inside the device and
even if it exists it is only a few 100 samples deep at most.
DMA support on the other hand allows to capture multiple millions or even
more samples without any CPU interaction. This allows the CPU to either go
to sleep for longer periods or focus on other tasks which increases overall
system performance and power consumption. In addition to that some devices
might not even offer a way to read the data other than using DMA, which
makes DMA mandatory to use for them.
The tasks involved in implementing a DMA buffer can be divided into two
categories. The first category is memory buffer management (allocation,
mapping, etc.) and hooking this up the IIO buffer callbacks like read(),
enable(), disable(), etc. The second category of tasks is to setup the
DMA hardware and manage the DMA transfers. Tasks from the first category
will be very similar for all IIO drivers supporting DMA buffers, while the
tasks from the second category will be hardware specific.
This patch implements a generic infrastructure that take care of the former
tasks. It provides a set of functions that implement the standard IIO
buffer iio_buffer_access_funcs callbacks. These can either be used as is or
be overloaded and augmented with driver specific code where necessary.
For the DMA buffer support infrastructure that is introduced in this series
sample data is grouped by so called blocks. A block is the basic unit at
which data is exchanged between the application and the hardware. The
application is responsible for allocating the memory associated with the
block and then passes the block to the hardware. When the hardware has
captured the amount of samples equal to size of a block it will notify the
application, which can then read the data from the block and process it.
The block size can freely chosen (within the constraints of the hardware).
This allows to make a trade-off between latency and management overhead.
The larger the block size the lower the per sample overhead but the latency
between when the data was captured and when the application will be able to
access it increases, in a similar way smaller block sizes have a larger per
sample management overhead but a lower latency. The ideal block size thus
depends on system and application requirements.
For the time being the infrastructure only implements a simple double
buffered scheme which allocates two blocks each with half the size of the
configured buffer size. This provides basic support for capturing
continuous uninterrupted data over the existing file-IO ABI. Future
extensions to the DMA buffer infrastructure will give applications a more
fine grained control over how many blocks are allocated and the size of
each block. But this requires userspace ABI additions which are
intentionally not part of this patch and will be added separately.
Tasks of the second category need to be implemented by a device specific
driver. They can be hooked up into the generic infrastructure using two
simple callbacks, submit() and abort().
The submit() callback is used to schedule DMA transfers for blocks. Once a
DMA transfer has been completed it is expected that the buffer driver calls
iio_dma_buffer_block_done() to notify. The abort() callback is used for
stopping all pending and active DMA transfers when the buffer is disabled.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds a enable and disable callback that is called when the
buffer is enabled/disabled. This can be used by buffer implementations that
need to do some setup or teardown work. E.g. a DMA based buffer can use
this to start/stop the DMA transfer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
For buffers which have a fixed wake-up watermark the watermark attribute
should be read-only. Add a new FIXED_WATERMARK flag to the
struct iio_buffer_access_funcs, which can be set by a buffer
implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Only initialize the watermark field if it is still 0. This allows drivers
to provide a custom default watermark value. E.g. some driver might have a
fixed watermark or can only support watermarks within a certain range and
the initial value for the watermark should be within this range.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently the watermark of the device is only set based on the watermark
that is set for the user space buffer. This doesn't consider the watermarks
set on any attached in-kernel buffers.
Change this so that the watermark of the device should be the minimum of
the watermarks over all attached buffers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
While the datasheet for the AD7785 lists 0xXB as the product ID the actual
product ID is 0xX3.
Fix the product ID otherwise the driver will reject the device due to non
matching IDs.
Fixes: e786cc26dc ("staging:iio:ad7793: Implement stricter id checking")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver Device Tree binding now documents compatible strings that have
a vendor prefix, so add these to the OF device ID table to match and mark
the old ones as deprecated explaining that should not be used anymore.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch moves the reference IIO dummy driver from drivers/staging/iio
into a separate folder, drivers/iio/dummy and adds the proper Kconfig
and Makefile for it.
A new config menu entry called IIO dummy driver has also been added
in the Industrial I/O support menu, corresponding to this driver.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ad5629/ad5669 are the I2C variant of the ad5628/ad5668, which has a SPI
interface. They are mostly identical with the exception that the shift
factor is different. Currently the driver does not take care of this
difference which leads to incorrect DAC output values.
Fix this by introducing a custom channel spec for the ad5629/ad5669 with
the correct shift factor.
Fixes: commit 6a17a0768f ("iio:dac:ad5064: Add support for the ad5629r and ad5669r")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
i2c_master_send() returns the number of bytes transferred on success while
the ad5064 driver expects that the write() callback returns 0 on success.
Fix that by translating any non negative return value of i2c_master_send()
to 0.
Fixes: commit 6a17a0768f ("iio:dac:ad5064: Add support for the ad5629r and ad5669r")
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Calculate ADCR_VTEMP25 using VTEMP25 at VREFH_ADC 3V3. Existing
calculations consider the typical values provided in datasheet.
Those typical values are valid for VREFH_ADC at 3.0V. VTEMP25
is different for different VREFH_ADC voltages. With VREFH_ADC
at 3.3V, voltage at 25°C is 0.699V. Hence update the VTEMP25
to 0.699V which gives ADCR@Temp25 as 867.
Formula for finding ADCR@Temp25:
ADCR@Temp25 = (ADCR@Vdd * V@TEMP25 * 10) / VDDconv
ADCR@Vdd for 12-Bit ADC = 4095
VDDconv = VREFH_ADC * 10
VREFH_ADC@3.3V
ADCR@Temp25 = (4095 * .699 * 10) / 33
ADCR@Temp25 ~= 867
| VREFH_ADC | V@TEMP25 | VDDconv | ADCR@Temp25 |
| 3.0V | 0.696mV | 30 | 950 |
| 3.3V | 0.699mV | 33 | 867 |
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Code was found at:
a90856a662%5E%21/#F1
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Marek Belisko <marek@goldelico.com> [Fixed minor typos + add channels list to documentation]
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This driver code was found as:
aaabb2e045/drivers/staging/iio/adc
Fixed various compilation issues and test this driver on omap5 evm.
Signed-off-by: Pradeep Goudagunta <pgoudagunta@nvidia.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds a minimal implementation for the Memsic MXC6255XC
orientation sensing accelerometer. The supported operations are reading
raw acceleration values for X/Y axis that can be scaled using the
exposed scale.
Signed-off-by: Teodora Baluta <teodora.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This change is important in order for everyone to be easily able to use the
driver for one of the supported accelerometer chips!
Until now, the driver blindly assumed that the INT1 interrupt line is wired
on a user's board. But these devices have 2 interrupt lines and can route
their interrupt sources to one of them. Now, if "INT2" is found and matches
i2c_client->irq, INT2 will be used.
The chip's default actually is INT2, which is why probably many boards will
have it wired and can make use of this.
Of course, this also falls back to assuming INT1, so for existing users
nothing will break. The new functionality is described in the bindings doc.
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
For the binding: Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch is a tidy up of warnings from the autobuilder.
>> drivers/iio/light/apds9960.c:495:32: sparse: cast to restricted __le16
drivers/iio/light/apds9960.c:635:24: sparse: cast to restricted __le16
>> drivers/iio/light/apds9960.c:672:21: sparse: incorrect type in assignment (different base types)
drivers/iio/light/apds9960.c:672:21: expected unsigned short [unsigned] [usertype] buf
drivers/iio/light/apds9960.c:672:21: got restricted __le16 [usertype] <noident>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: mranostay@gmail.com
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch changes various types to the appropriate endian specific
versions. Also introduces an additional local variable to avoid
a single variable being used for both be and cpu endianness.
These aren't bugs as such, but clearing them up does make the code
clearer.
Warning was:
sparse warnings: (new ones prefixed by >>)
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:126:9: sparse: cast to restricted __be32
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:126:9: sparse: cast to restricted __be32
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:126:9: sparse: cast to restricted __be32
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:126:9: sparse: cast to restricted __be32
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:126:9: sparse: cast to restricted __be32
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:126:9: sparse: cast to restricted __be32
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:127:16: sparse: cast to restricted __be32
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:127:16: sparse: cast to restricted __be32
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:127:16: sparse: cast to restricted __be32
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:127:16: sparse: cast to restricted __be32
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:127:16: sparse: cast to restricted __be32
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:127:16: sparse: cast to restricted __be32
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:208:18: sparse: incorrect type in assignment (different base types)
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:208:18: expected unsigned short [unsigned] [addressable] [usertype] send_buf
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:208:18: got restricted __be16 [usertype] <noident>
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:230:18: sparse: incorrect type in assignment (different base types)
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:230:18: expected unsigned short [unsigned] [addressable] [usertype] send_buf
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:230:18: got restricted __be16 [usertype] <noident>
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some regulators can supply multiple voltages. To take changing voltages
into account, the scale needs to be calculated on every read access.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix some indentation issues and separate returns by empty lines (IIO
style). Also rename the channel mask in _read_raw() to mask.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A return variable is not required in _write_raw(), and dropping it reduces
complexity, as well.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Make use of ARRAY_SIZE to prevent buffer issues.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The regulator framework requests to balance regulator_enable() calls with
regulator_disable() calls. To meet this requirement, set channels to 0 on
remove, which implies a regulator_disable() call in case that channel was
enabled.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This device simply uses its Vcc as reference voltage, so the same scale
applies for all channels. Also offset doesn't appear to be different for
any channel. Represent this by switching these two attributes to
info_mask_shared_by_type.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Previous offset wasn't applied in the correct order and invalid.
This patchset fixes this issue, and also has the correct scale value
applied to the offset.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Support for MS8607 temperature, pressure & humidity sensor.
This part is using functions from MS5637 for temperature and pressure
and HTU21 for humidity
Signed-off-by: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Support for MS5637 temperature & pressure sensor
Signed-off-by: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Support for HTU21 temperature & humidity sensor
Signed-off-by: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Support for TSYS02D temperature sensor
Signed-off-by: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Support for TSYS01 temperature sensor
Signed-off-by: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Measurement specialties drivers common part.
These functions are used by further drivers
in the patchset: TSYS01, TSYS02D, HTU21, MS5637, MS8607
Signed-off-by: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a simple SPI driver which initializes the spi regmap for the bmc150
core driver.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
i2c_client struct is now only used for debugging output. We can use the
device struct as well so we can remove all struct i2c_client usage.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This replaces all usage of direct i2c accesses with regmap accesses.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Commit 845c877009 ("i2c / ACPI: Assign IRQ for devices that have
GpioInt automatically") automatically assigns the first ACPI GPIO
interrupt in client->irq, so we can remove the probing code from
drivers that use only one interrupt.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Since commit dab472eb93 ("i2c / ACPI: Use 0 to indicate that
device does not have interrupt assigned") 0 is not a valid i2c
client irq anymore, so change all driver's checks accordingly.
The same issue occurs when the device is instantiated via device tree
with no IRQ, or from the i2c sysfs interface, even before the patch
above.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This accelerometer accidentally either emits a DRDY signal or an
IRQ signal. Accidentally I activated the IRQ signal as I thought
it was analogous to the interrupt generator on other ST
accelerometers. This was wrong. After this patch generic_buffer
gives a nice stream of accelerometer readings.
Fixes: 3acddf74f8 "iio: st-sensors: add support for lis3lv02d accelerometer"
Cc: Denis CIOCCA <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
MADC[3:6] reads incorrect values without these two following changes:
- enable the 3v1 bias regulator for ADC[3:6]
- configure ADC[3:6] lines as input, not as USB
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Dan Carpenter reported a static checker report and after his mail I
noticed that we actually return from function if positive value is
obtained from i2c read. This was remainder from when code was not in
separate function (which I changed during the review process).
Static checker reported
drivers/iio/temperature/mlx90614.c:167
mlx90614_iir_search()
warn: this cast is a no-op
which meant that cast before negating is useless. Dan also proposed a
solution on nicer bit operation form.
Also changed magic number to macro in process as that was confusing.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The device tree compatible strings weren't properly
registered for the pulsedlight-lidar-lite-v2 driver.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Chipset sometime updates in the middle of a reading causing it
to reset the data pointer, and causing invalid reading of previous data.
We can check for this invalid state by reading MSB of the resistance
reading that is always zero, and by also confirming the VOC_short isn't
zero.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This shouldn't actually change anything since the core calls the events
sysfs folder "events" anyways.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This shouldn't actually change anything since the core calls the events
sysfs folder "events" anyways.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This shouldn't change anything since the core calls the events folder
"events" anyways.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New device support
* APDS9960 ALS + proximity driver
* bmg160 SPI devices.
* HDC100x humidity sensors
* Holt HI-8435 threshold detector
* mma8453Q accelerometer added to the mma8452 driver
* mma86452FC and mma8653FC accelerometers added to the mma8452 driver
* mxc4005 accelerometer
* PulsedLight LIDAR
* SensorTech VZ89x volatile organic compound sensor
* UPISEMI uS5182d ALS and proximity sensors
New core functionality
* triggered events - use triggers to check for changes in threshold type
detectors on devices with out interrupt support. First user is the holt
comparator.
* chemical concentration and resistance channel types.
New driver functionality
* vf610
- buffer support.
- followup coccinelle warning fix.
Core rework
* buffers
- break out callback buffer to own module.
- move buffer implementations to a new subdirectory
* percolate the error code form iio_event_getfd out to userspace
rather than giving a missleading error later on.
Cleanups
* adddac drivers
- use BIT macro where appropriate.
* meter drivers
- use BIT macro where appropriate.
* ad7303
- add an OF match table to line up with the binding docs.
* adc128s052
- add an OF match table to line up with the binding docs.
* adf4350
- add an OF match table to line up with the binding docs
* as3935
- add an OF match table to line up with the binding docs.
* berlin2-adc
- use GENMASK and BIT for masks
- prevent attempting to sample multiple channels at once by moving a
mutex scop
- coding style cleanups
* bmg150_magn
- kconfig sort order was wrong - fix it.
* bmg160
- use i2c regmap and drop all uses of i2c_client
- separate i2c and core driver
* cc10001_adc
- kconfig sort order was wrong - fix it.
* evgen (dummy driver helper module)
- move interrupt generation to irq_work to reduce differences between
the dummy driver and real hardware drivers.
* hmc5843
- set the name dynamically rather than to a fixed value for one of the
suported parts.
- export module alias information to allow autoprobing of module.
* lpc32xx
- on failure to get resource or irq return -ENXIO as uppose to -EBUSY
* max1027
- set .of_match_table to actually allow OF style matching.
* max5821
- add MODULE_DEVICE_TABLE for OF table.
* mma8452
- refactor to separate out chip specific data.
- add freefall / motion interrupt source for devices that do their
interrupts slightly differently.
- update copywrite notice.
- leave naming of events directory in sysfs to the core
* mcp320x
- set .of_match_table so that it can be use for OF style matching.
* mlx90614
- Implement filter configuration (note the datasheet changed as a result
of the driver reviews to include the values we needed ;)
* opt3001
- drop .owner field as assigned by platform driver core.
* si7020
- replace a bitmask on the humidity values with a more correct range
check.
* stk310
- improved error handling.
- use BIT macro where appropriate and use the resulting defines
instead of magic numbers in the code.
- fix indentation
* st-sensors
- add debugfs register read hook
* tsl4531
- fix error handling in check_id
* twl6030
- fix module autoload for OF
* iio-trig-sysfs
- document add and remove attribute
* trigger in staging
- code alignment fixes.
- braces on both branches of if statement if needed for one.
* xilinx-xadc
- push interrupts into hardirq context as there isn't much in them
any more and it avoids breaking PREEMPT_RT builds due to the use
of a spinlock between the hardirq and the thread.
Tools
* event-monitor
- report unsupported events. We keep expanding what can come from drivers
so give a helpful error if one turns up in an out of date userspace
program.
* generic-buffer
- helpful message about needing to enable a channel to start the buffer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=E+jf
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.4a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new driver, new functionality and cleanups for IIO in the 4.4 cycle
New device support
* APDS9960 ALS + proximity driver
* bmg160 SPI devices.
* HDC100x humidity sensors
* Holt HI-8435 threshold detector
* mma8453Q accelerometer added to the mma8452 driver
* mma86452FC and mma8653FC accelerometers added to the mma8452 driver
* mxc4005 accelerometer
* PulsedLight LIDAR
* SensorTech VZ89x volatile organic compound sensor
* UPISEMI uS5182d ALS and proximity sensors
New core functionality
* triggered events - use triggers to check for changes in threshold type
detectors on devices with out interrupt support. First user is the holt
comparator.
* chemical concentration and resistance channel types.
New driver functionality
* vf610
- buffer support.
- followup coccinelle warning fix.
Core rework
* buffers
- break out callback buffer to own module.
- move buffer implementations to a new subdirectory
* percolate the error code form iio_event_getfd out to userspace
rather than giving a missleading error later on.
Cleanups
* adddac drivers
- use BIT macro where appropriate.
* meter drivers
- use BIT macro where appropriate.
* ad7303
- add an OF match table to line up with the binding docs.
* adc128s052
- add an OF match table to line up with the binding docs.
* adf4350
- add an OF match table to line up with the binding docs
* as3935
- add an OF match table to line up with the binding docs.
* berlin2-adc
- use GENMASK and BIT for masks
- prevent attempting to sample multiple channels at once by moving a
mutex scop
- coding style cleanups
* bmg150_magn
- kconfig sort order was wrong - fix it.
* bmg160
- use i2c regmap and drop all uses of i2c_client
- separate i2c and core driver
* cc10001_adc
- kconfig sort order was wrong - fix it.
* evgen (dummy driver helper module)
- move interrupt generation to irq_work to reduce differences between
the dummy driver and real hardware drivers.
* hmc5843
- set the name dynamically rather than to a fixed value for one of the
suported parts.
- export module alias information to allow autoprobing of module.
* lpc32xx
- on failure to get resource or irq return -ENXIO as uppose to -EBUSY
* max1027
- set .of_match_table to actually allow OF style matching.
* max5821
- add MODULE_DEVICE_TABLE for OF table.
* mma8452
- refactor to separate out chip specific data.
- add freefall / motion interrupt source for devices that do their
interrupts slightly differently.
- update copywrite notice.
- leave naming of events directory in sysfs to the core
* mcp320x
- set .of_match_table so that it can be use for OF style matching.
* mlx90614
- Implement filter configuration (note the datasheet changed as a result
of the driver reviews to include the values we needed ;)
* opt3001
- drop .owner field as assigned by platform driver core.
* si7020
- replace a bitmask on the humidity values with a more correct range
check.
* stk310
- improved error handling.
- use BIT macro where appropriate and use the resulting defines
instead of magic numbers in the code.
- fix indentation
* st-sensors
- add debugfs register read hook
* tsl4531
- fix error handling in check_id
* twl6030
- fix module autoload for OF
* iio-trig-sysfs
- document add and remove attribute
* trigger in staging
- code alignment fixes.
- braces on both branches of if statement if needed for one.
* xilinx-xadc
- push interrupts into hardirq context as there isn't much in them
any more and it avoids breaking PREEMPT_RT builds due to the use
of a spinlock between the hardirq and the thread.
Tools
* event-monitor
- report unsupported events. We keep expanding what can come from drivers
so give a helpful error if one turns up in an out of date userspace
program.
* generic-buffer
- helpful message about needing to enable a channel to start the buffer.
drivers/iio/light/apds9960.c:1125:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
drivers/iio/light/apds9960.c:986:1-4: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
CC: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
drivers/iio/adc/vf610_adc.c:766:1-4: WARNING: end returns can be simpified and declaration on line 755 can be dropped
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
CC: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for UPISEMI us5182d als and proximity sensor.
Supports raw readings.
Data sheet for this device can be found here:
http://www.upi-semi.com/temp/uS5182D-DS-P0103-temp.pdf
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for VZ89X sensors VOC and CO2 reporting channels in
percentage which can be converted to part per million.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There are air quality sensors that report data back in parts per million
of VOC (Volatile Organic Compounds) which are usually indexed from CO2
or another common pollutant.
This patchset adds an IIO_CONCENTRATION type that returns a percentage
of substance because no other channels types fit this use case.
Modifiers for IIO_MOD_CO2 and IIO_MOD_VOC gas types are defined.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This doesn't actually change anything since the core names the sysfs folder
for the iio event attributes "events" anyways. It only leaves the job to the
core.
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
MMA8652FC and MMA8653FC don't provide the transient interrupt source, so
the motion interrupt source is used by providing a new iio_chan_spec
definition, so that other supported devices are not affected by this.
Datasheets for the newly supported devices are available at Freescale's
website:
http://cache.freescale.com/files/sensors/doc/data_sheet/MMA8652FC.pdfhttp://cache.freescale.com/files/sensors/doc/data_sheet/MMA8653FC.pdf
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds the freefall / motion interrupt source definitions to the driver.
It is used in this series' next patch, for chips that don't support the
transient interrupt source.
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for the 10 bit version if Freescale's accelerometers
of this series. The datasheet is available at Freescale's website:
http://cache.freescale.com/files/sensors/doc/data_sheet/MMA8453Q.pdf
It creates a devicetree bindings file to document the new functionality
and removes the driver from the trivial-devices list.
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds a struct mma_chip_info to hold data that will remain specific to
the chip in use. It is provided during probe() and linked in
struct of_device_id.
Also this suggests that the driver is called "mma8452" and now handles the
MMA8452Q device, but is not limited to it.
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the HDC100x temperature and humidity sensors
including the resistive heater element.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc
versions of the descriptor calls that did not use the flags
argument on the end. This was around for too long and eventually
Uwe Kleine-König took the time to clean it out and the last
users are removed along with the macros in this tag. In several
cases the use of flags simplifies the code. For this reason we
have (ACKed) patches hitting in DRM, IIO, media, NFC, USB+PHY
up until we hammer in the nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff
we have i the kernel to discourage people from reinventing
a square wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO
IRQ chip instead of using one class for all chips, as the current
code will not work with systems with several GPIO chips doing
lockdep debugging.
- Protect against driver unloading also when a GPIO line is only
used as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent
device driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing
all call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a
combined call to irq_set_chained_handler_and_data(). This
series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which
is way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs
from IRQ numbers. The goal is to get rid of the irq number
from the handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO
drivers. This was an ARM specific function that is replaced
with the generic irq_modify_status() where special flags
are actually needed.
- When an OF node has a pin range for its GPIOs, return
-EPROBE_DEFER if the pin controller isn't available.
Pretty logical, yet needed to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own
irq_*_resources call back, then call these instead of the
defaults provided by the GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not
properly documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the
generic GPIO driver.
- Clean out platform data support from the Emma Mobile (EM)
driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver,
we now support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iQ2P
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.3 kernel cycle.
There is quite a lot going on in the GPIO subsystem this merge window,
so the main matter is decribed below.
The hits in other subsystems when making the GPIO flags optional are
all ACKed by their respective subsystem maintainers.
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc versions
of the descriptor calls that did not use the flags argument on the
end. This was around for too long and eventually Uwe Kleine-König
took the time to clean it out and the last users are removed along
with the macros in this tag. In several cases the use of flags
simplifies the code. For this reason we have (ACKed) patches
hitting in DRM, IIO, media, NFC, USB+PHY up until we hammer in the
nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff we
have i the kernel to discourage people from reinventing a square
wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO IRQ
chip instead of using one class for all chips, as the current code
will not work with systems with several GPIO chips doing lockdep
debugging.
- Protect against driver unloading also when a GPIO line is only used
as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent device
driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data().
This series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO drivers.
This was an ARM specific function that is replaced with the generic
irq_modify_status() where special flags are actually needed.
- When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER
if the pin controller isn't available. Pretty logical, yet needed
to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own irq_*_resources call
back, then call these instead of the defaults provided by the
GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not properly
documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the generic
GPIO driver.
- Clean out platform data support from the Emma Mobile (EM) driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver, we now
support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver"
* tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: extraxfs: fix returnvar.cocci warnings"
gpio: tc3589x: use static container helper
gpio: xlp: fix error return code
gpio: vf610: handle level IRQ's properly
gpio: max732x: Fix error handling in probe()
gpio: omap: fix clk_prepare/unprepare usage
gpio: omap: protect regs access in omap_gpio_irq_handler
gpio: omap: fix omap2_set_gpio_debounce
gpio: omap: switch to use platform_get_irq
gpio: omap: remove wrong irq_domain_remove usage in probe
gpiolib: add description for gpio irqchip fields in struct gpio_chip
gpio: extraxfs: fix returnvar.cocci warnings
gpiolib: irqchip: use different lockdep class for each gpio irqchip
gpio/grgpio: fix deadlock in grgpio_irq_unmap()
Documentation: gpio: consumer: describe active low property
gpio: mxc: fix section mismatch warning
gpio/mxc: mask gpio interrupts in suspend
gpio: omap: Fix missing raw locks conversion
gpio: brcmstb: support wakeup from S5 cold boot
gpio: brcmstb: Add interrupt and wakeup source support
...
Add iio trigger for the data ready interrupt that signals new
measurements for the X, Y and Z axes.
Signed-off-by: Teodora Baluta <teodora.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for buffered readings for the 3-axis
accelerometer mxc4005.
Signed-off-by: Teodora Baluta <teodora.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for Memsic MXC4005XC 3-axis accelerometer. The
current implementation is a minimal one as it adds raw readings for the
three axes and setting scale from userspace.
Signed-off-by: Teodora Baluta <teodora.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch separates the core driver using regmap and the i2c driver
which creates the i2c regmap. Also in the Kconfig file BMG160 and
BMG160_I2C are separate now.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
