In case we have transfers which aren't aligned
to wMaxPacketSize, we need to be careful with
how we start the transfer with the HW. OUT
transfers _must_ be aligned with wMaxPacketSize
and in order to guarantee that, we use a bounce
buffer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This core cannot handle OUT transfers which aren't
aligned to wMaxPacketSize, but that can happen at
least on control endpoint with the USB Audio Class.
This patch adds a bounce buffer to be used on the
case of a non-aligned ep0out request is queued.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The status field of the Transfer Not Read event
is different on Control Endpoints. On this patch
we are just adding the defines to be used on a
later patch which will re-work the control endpoint
handling.
Signed-off-by: Felipe Balbi <balbi@ti.com>
the previous message had too little meaning. Make
it more human readable and use the macro we already
had for extracting the command completion status out
of DEPCMDn register.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if we don't set DMA address to invalid when unmapping,
we might fall in a situation where request buffer
can't be mapped to DMA again.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We may as well fix this potential leak so we don't have to listen to
the static checkers complain.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Without this patch we won't clear that bit and instead will
clear all other bits on our endpoint flag.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Type 6 should be used for the first transfer during an interval. This is
also what the reference driver is using. Type 7 seems to be for following
or additional transfers within the same interval.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we collected two requests together (i.e. only the last of them has
LST=1) then we only have to stop transfer once: The clean-up code will
cleanup everything until first TRB with the LST bit set.
After XferComplete this index should be no longer valid since there is
no transfer pending.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A TRB which is dequeued seems to have its HWO bits set to 1. Therefore
we ignore it if we dequeue it after the command is completed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch changes rts51x_read_mem, rts51x_write_mem, and rts51x_read_status to
allocate temporary buffers with kmalloc. This way stack addresses are not used
for DMA when these functions call rts51x_bulk_transport.
Signed-off-by: Adam Cozzette <acozzette@cs.hmc.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the MACH_MX* macros are scheduled for removal, so just depend
on ARCH_MXC instead. The Kconfig text makes it clear on which
SoC the driver runs on.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ARCH_MX1 scheduled for removal. Instead, depend on ARCH_MXC
and make clear in the Kconfig text that only i.MX1 has this
hardware.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build error when CONFIG_USB_GADGET_DWC3 is not enabled:
ERROR: "dwc3_send_gadget_ep_cmd" [drivers/usb/dwc3/dwc3.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now ${LINUX}/drivers/usb/* can use usb_endpoint_maxp(desc) to get maximum packet size
instead of le16_to_cpu(desc->wMaxPacketSize).
This patch fix it up
Cc: Armin Fuerst <fuerst@in.tum.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Johannes Erdfelt <johannes@erdfelt.com>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: David Kubicek <dave@awk.cz>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Brad Hards <bhards@bigpond.net.au>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: David Lopo <dlopo@chipidea.mips.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Xie Xiaobo <X.Xie@freescale.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Jiang Bo <tanya.jiang@freescale.com>
Cc: Yuan-hsin Chen <yhchen@faraday-tech.com>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Xiaochen Shen <xiaochen.shen@intel.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: OKI SEMICONDUCTOR, <toshiharu-linux@dsn.okisemi.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Herbert Pötzl <herbert@13thfloor.at>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Roman Weissgaerber <weissg@vienna.at>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: Florian Floe Echtler <echtler@fs.tum.de>
Cc: Christian Lucht <lucht@codemercs.com>
Cc: Juergen Stuber <starblue@sourceforge.net>
Cc: Georges Toth <g.toth@e-biz.lu>
Cc: Bill Ryder <bryder@sgi.com>
Cc: Kuba Ober <kuba@mareimbrium.org>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes this build error:
drivers/usb/dwc3/dwc3-pci.c: In function 'dwc3_pci_init':
drivers/usb/dwc3/dwc3-pci.c:211:9: error: 'THIS_MODULE' undeclared (first use in this function)
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Executing
| testusb -a -c 1 -t 3 -v 421 -s 2048
does not complete on the gadget side.
g_zero enqueues a 4096 bytes long buffer. The host sends 2048bytes which
is a multiple of wMaxPacketSize (either 64 or 512 bytes). The host is
done with sending data but the gadget waits for more.
Since the protocol does not include transfer-length-field sending a
terminating zero packet seems the only way out.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MPC832x does not have enough MURAM to do fixed MURAM allocation.
Change to dynamic allocation.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a low or full speed urb in progress is unlinked (or some other error
occurs), the buffer in the transaction translator (part of the hub) might end
up in an inconsistent state. This can make all further low and full speed
transactions fail, unless the buffer is cleared.
The bug can be seen when running the usbtest unlink tests as "set altsetting
to 0 failed, -110", and gets fixed by this patch.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Test the just-initialized value rather than some other one.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier x,y,f!={PTR_ERR,ERR_PTR,ERR_CAST};
statement S;
@@
x = f(...);
(
if (\(x == NULL\|IS_ERR(x)\)) S
|
*if (\(y == NULL\|IS_ERR(y)\))
{ ... when != x
return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the unused function twl6030_set_phy_clk of twl6030-usb.c.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Makes it possible to use i.e. gpio-vbus to handle vbus events.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb-interrupt is requested before the endpoints are initalised.
If an interrupt happens in the time between request_irq and the init
of the endpoint-data (as seen on the Qisda ESx00 ebook-platforms),
it is therefore possible for the interrupt handler to access endpoint-
data before its creation resulting in a null-pointer dereference.
This patch simply moves the irq request below the endpoint init.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'll be focussed on this driver and can maintain
it without any problem.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DesignWare USB3 is a highly
configurable IP Core which can be
instantiated as Dual-Role Device (DRD),
Peripheral Only and Host Only (XHCI)
configurations.
Several other parameters can be configured
like amount of FIFO space, amount of TX and
RX endpoints, amount of Host Interrupters,
etc.
The current driver has been validated with
a virtual model of version 1.73a of that core
and with an FPGA burned with version 1.83a
of the DRD core. We have support for PCIe
bus, which is used on FPGA prototyping, and
for the OMAP5, more adaptation (or glue)
layers can be easily added and the driver
is half prepared to handle any possible
configuration the HW engineer has chosen
considering we have the information on
one of the GHWPARAMS registers to do
runtime checking of certain features.
More runtime checks can, and should, be added
in order to make this driver even more flexible
with regards to number of endpoints, FIFO sizes,
transfer types, etc.
While this supports only the device side, for
now, we will add support for Host side (xHCI -
see the updated series Sebastian has sent [1])
and OTG after we have it all stabilized.
[1] http://marc.info/?l=linux-usb&m=131341992020339&w=2
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
not to confuse with Table 9-7 in USB 2.0 spec
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1483) improves the ehci-hcd driver family by getting rid
of the reliance on the hcd->state variable. It has no clear owner and
it isn't protected by the usual HCD locks. In its place, the patch
adds a new, private ehci->rh_state field to record the state of the
root hub.
Along the way, the patch removes a couple of lines containing
redundant assignments to the state variable. Also, the QUIESCING
state simply gets changed to the RUNNING state, because the driver
doesn't make any distinction between them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add supprt for on-chip USB controller for Netlogic XLS MIPS64
SoC processor family.
Changes are:
- update ehci-hcd.c and ohci-hcd.c to add XLS hcds
- add ehci-xls.c: EHCI support for Netlogic XLS.
- add ohci-xls.c: OHCI support for Netlogic XLS.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These messages just clutter the log and provide no useful information to
the user, so make them pr_debug().
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1) A bug in the usage of time_after() in errata2_function().
2) Clear done_maps just prior to starting a new transfer in
start_bus_transfer(), instead of just after, when done_map bits might have
been validly set by the started transfer.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
... and some small code style fixes.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Errata 2 for the isp1760 explains that the chip sometimes does not issue
interrupts when an ATL (bulk or control) transfer is completed. There are
several issues with the current work-around (SOF interrupts) for this:
1) It seems the chip sometimes does not even set the done bit for a
completed transfer, in which case SOF interrupts does not solve
the problem since we still check the done map to find out which
transfer descriptors to handle.
2) The above point seems to happen only when ATL and SOF interrupts
are enabled at the same time. However, disabling ATL interrupts
increases the latency between transfer completion and handling.
This is very noticeable in the testusb suite, which take several
minutes more to run with ATL interrupts disabled.
This patch removes the code to switch on SOF interrupts, and instead
use a kernel timer to periodically check for "old" descriptors that
have their VALID and ACTIVE flags unset, indicating completion, thus
avoiding the dependency on the chip's done map (and SOF interrupts)
to find transfers affected by this HW bug.
[bigeasy@linutronix: 80 lines limit]
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Like the previous patch, this patch has been split from the next one
for clarity.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the few lines of code in isp1760_enable_interrupts() and
isp1760_init_maps() into isp1760_run(). This makes the following patch
easier.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From 2d487c10136f76cf3705881d34868e8592839cfe Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Tue, 12 Jul 2011 15:36:51 +0200
Subject: [PATCH] USB: ipw: convert to usb-wwan framework
This patch allows the ipw driver to use the multibuffer
infrastructure of usb-wwan. This improves speed.
Signed-off-by: Oliver Neukum<oneukum@suse.de>
Tested-by: Michal Hybner <dta081@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Scanning cannot be run during suspend or hibernation, but if
usb-stor-scan freezes another thread waiting on scanning to
complete may fail to freeze.
However, if usb-stor-scan is left freezable without ever actually
freezing then the freezer will wait on it to exit, and threads
waiting for scanning to finish will no longer be blocked. One
problem with this approach is that usb-stor-scan has a delay to
wait for devices to settle (which is currently the only point where
it can freeze). To work around this we can request that the freezer
send a fake signal when freezing, then use interruptible sleep to
wake the thread early when freezing happens.
To make this happen, the following changes are made to
usb-stor-scan:
* Use set_freezable_with_signal() instead of set_freezable() to
request a fake signal when freezing
* Use wait_event_interruptible_timeout() instead of
wait_event_freezable_timeout() to avoid freezing
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In drivers/usb/core/hub.c::usb_disconnect(), 'udev' will never be
NULL, so remove the test and printing of debug message.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
