Atmel touchscreen chips have different firmware version with each chip,
so we cannot distinguish attribute of chip by firmware version.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Explicitly set all the enable bits when opening the device just in case
something left the device in an unexpected state.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The AT42QT1070 QTouch sensor supports up to 7 keys.
The driver has been tested on Atmel AT91SAM9M10-G45-EK board, and it
should work fine on other platforms.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
tslib expects pressure measurements so enable them by default for better
compatibility.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch add multitouch support for the MacBookPro8,1 and
MacBookPro8,2 models.
Cc: stable@kernel.org
Signed-off-by: Andy Botting <andy@andybotting.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are two types of 1FGT devices supported in wacom_wac.c.
Changing them to follow the existing touchscreen format, i.e.,
only report BTN_TOUCH as a valid tool type.
Touch data will be ignored if pen is in proximity. This requires
a touch up event sent if touch was down when pen comes in. The
touch up event should be sent before any pen events are emitted.
Otherwise, two pointers would race for the cursor.
However, we can not send a touch up inside wacom_tpc_pen since
pen and touch are on different logical port. That is why we
have to check if touch is up before sending pen events.
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
So it would be easier for patch reviewers to follow the data path.
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2FGT Tablet PC touch events were processed in _TAP_ format. Remove
them so we can change to _MT_ format.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The mxt_check_matrix_size() is currently setting the CTE mode to match
xline/yline information that is in the platform data, but it does not
take into account for example the fact that we could have a key array
in use too (key array would use some x/y lines as well).
It would be better to simply rely on the configuration data, and make
sure that the CTE mode set in there matches the touch object (touchscreen,
key array, proximity) configuration (which are set in the config data too).
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The MCS50XX series has a HW bug that requires explicit chip power down.
If chip is not powered down before shutting the system down the control
pins (powerup, interrupt) are pulled up and residue current continues
flowing into the chips making them continue consuming power.
Signed-off-by: Heungjun Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds support for system-level suspend/resume to the driver.
Signed-off-by: Heungjun Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Enable Runtime PM functionality in OMAP4 driver based on the following
assumptions:
- keyboard controller in wakeup domain so it is always on and power
impact is minimal;
- in OMAP4 the device control is at module/device level and ick/fclk
level control is difficult so cutting of clocks will prevent
interrupts.
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The test here is reversed. It should be if (IS_ERR()) instead of
if (!IS_ERR()).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Different board have different requirements/setups so let's be more
flexible.
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
As there is no common configuration settings that would work in every
situation, remove the fixed config data from driver code and add
config data to platform data.
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
"mXT224" is used in the Intel mid firmware in SFI tables to identify the
presence of this I2C device.
Signed-off-by: Chris Leech <christopher.leech@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move to convert drivers to dev_pm_ops rather than bus
specific PM ops in order to facilitate core development. Do this converison
for synaptics-i2c.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The adxl34x SPI driver has what appears to be a typo referring to the
device as adx134x with the numeral 1 rather than letter l. This appears
to be an error so convert.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move to convert drivers to use dev_pm_ops rather than
bus specific ones in order to facilitate core development. Do this
conversion for adxl34x-spi.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move to convert drivers to use dev_pm_ops rather than
bus specific ones in order to facilitate core development. Do this
conversion for adxl34x-i2c.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move to convert drivers to use dev_pm_ops rather than
bus specific ops to facilitate core work. Do this conversion for max7359.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move away from bus specific PM operations to using
dev_pm_ops in order to facilicate core improvements. Update lm8323 to
the new model.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move to convert drivers to use dev_pm_ops rather than
bus specific PM operations in order to facilitate core work. Do this
conversion for ad714x-spi.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move to convert drivers to use dev_pm_ops rather than
bus specific PM operations in order to facilitate core work. Do this
conversion for ad714x-i2c.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of open-coding copying of data structures from userspace use
memdup_user() and strndup_user(). Note that this introduces change in
behavior because driver used to truncate 'phys' longer than 1024 bytes,
but now it will refuse to set 'phys' that long. Arguably trying to set
such 'phys' is suspect anyways.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The check for non-empty device name was botched since we tried to account
for extra space for the terminating zero at the same time. Convert to
kstrndup() to avoid this problem.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Aristeu Rozanski <aris@ruivo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Read the whole message, as reading just the first byte isn't always
guaranteed to clear the message.
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Change prefixes from qt602240 to mxt to reflect that the driver supports
whole line of mXT touchscreens.
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since the driver will be supporting whole range of Atmels mXT touchscreen
controllers we better rename it to atmel_mxt_ts.
Acked-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
All users of old style get/setkeycode methids have been converted so
it is time to retire them.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
While being applied the driver was modified to add use of the ternary
operator. Write the conditionals out longhand as I find it terribly
unhelpful for legibility.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
arch/arm/mach-omap2/dma.c: Convert IS_ERR result to PTR_ERR
arm: omap2: mux: fix compile warning
omap1: Simplify use of omap_irq_flags
omap2+: Fix unused variable warning for omap_irq_base
Fix kernel-doc warning in kernel.h from commit 7ef88ad561
("BUILD_BUG_ON: make it handle more cases"):
Warning(include/linux/kernel.h:605): No description found for parameter 'condition'
Warning(include/linux/kernel.h:605): Excess function parameter 'cond' description in 'BUILD_BUG_ON'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patches should keep coming through Rusty but it helps if I'm Cc'd as
well.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (42 commits)
usb: gadget: composite: avoid access beyond array max length
USB: serial: handle Data Carrier Detect changes
USB: gadget: Fix endpoint representation in ci13xxx_udc
USB: gadget: Fix error path in ci13xxx_udc gadget probe function
usb: pch_udc: Fix the worning log issue at gadget driver remove
USB: serial: Updated support for ICOM devices
USB: ehci-mxc: add work-around for efika mx/sb bug
USB: unbreak ehci-mxc on otg port of i.MX27
drivers: update to pl2303 usb-serial to support Motorola cables
USB: adding USB support for Cinterion's HC2x, EU3 and PH8 products
USB serial: add missing .usb_driver field in serial drivers
USB: ehci-fsl: Fix 'have_sysif_regs' detection
USB: g_printer: fix bug in module parameter definitions
USB: g_printer: fix bug in unregistration
USB: uss720: remove duplicate USB device
MAINTAINERS: add ueagle-atm entry
USB: EHCI: fix DMA deallocation bug
USB: pch_udc: support new device ML7213 IOH
usb: pch_udc: Fixed issue which does not work with g_serial
usb: set ep_dev async suspend should be later than device_initialize
...
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (26 commits)
staging: r8712u: Add new device IDs
staging: brcm80211: fix suspend/resume issue in brcmsmac
staging: brcm80211: remove assert to avoid panic since 2.6.37 kernel
Staging: iio: Aditional fixpoint formatted output bugfix
staging: usbip: vhci: use urb->dev->portnum to find port
staging: usbip: vhci: handle EAGAIN from SO_RCVTIMEO
staging: usbip: vhci: friendly log messages for connection errors
staging: usbip: vhci: refuse to enqueue for dead connections
staging: usbip: vhci: give back URBs from in-flight unlink requests
staging: usbip: vhci: update reference count for usb_device
staging: usbip: stub: update refcounts for devices and interfaces
staging: tidspbridge: replace mbox callback with notifier_call
staging: comedi: ni_labpc: Use shared IRQ for PCMCIA card
Staging: speakup: &&/|| confusion in silent_store()
iio: Fixpoint formatted output bugfix
staging: rt2860: Fix incorrect netif_stop_queue usage warning
staging: r8712u: Fix memory leak in firmware loading
staging: tidspbridge: configure full L1 MMU range
staging: rt2870sta: Add ID for Linksys WUSB100v2
Staging: xgfib: put parenthesis in the right place
...
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty/serial: fix apbuart build
n_hdlc: fix read and write locking
serial: unbreak billionton CF card
tty: use for_each_console() and WARN() on sysfs failures
vt: fix issue when fbcon wants to takeover a second time.
Fix up trivial conflict in drivers/tty/tty_io.c
Allow non-ARM SMP processors to use the SMP_ON_UP feature. CPUs
supporting SMP must have the new CPU ID format, so check for this first.
Then check for ARM11MPCore, which fails the MPIDR check. Lastly check
the MPIDR reports multiprocessing extensions and that the CPU is part of
a multiprocessing system.
Cc: <stable@kernel.org>
Reported-and-Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that the ISA/PCI IO space accessors are properly ordered on
ARMv6+ architectures. These should always be ordered with respect to
all other accesses.
This also fixes __iormb() and __iowmb() not being visible to ioread/
iowrite if a platform defines its own MMIO accessors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Disable the initrd if the passed address already overlaps the reserved
region. This avoids oopses on Netwinders when NeTTrom tells the kernel
that an initrd is located at mem+4MB, but this overlaps the BSS,
resulting in the kernels in-use BSS being freed.
This should be applied to v2.6.37-stable.
Cc: <stable@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
0ea1293 (arm: return both physical and virtual addresses from addruart)
changed the way the 'addruart' worked, making it return both the virt
and phys addresses. Unfortunately, for footbridge, these were reversed.
Fix that. Tested on Netwinder.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We should not report incomplete blocks on error. Return the number of
bytes successfully transferred, rounded down to the nearest block.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>