These are Gen3 Aquantia N-BASET PHYs which support 5GBASE-T,
2.5GBASE-T, 1000BASE-T and 100BASE-TX (not 10G); also EEE, Sync-E,
PTP, PoE.
The 112 is a single PHY package, the 412 is a quad PHY package.
The system-side SERDES interface of these PHYs selects its protocol
depending on the negotiated media side link speed. That protocol can be
1000BASE-X, 2500BASE-X, 10GBASE-R, SGMII, USXGMII.
The configuration of which SERDES protocol to use for which link speed
is made by firmware; even though it could be overwritten over MDIO by
Linux, we assume that the firmware provisioning is ok for the board on
which the driver probes.
For cases when the system side runs at a fixed rate, we want phylib/phylink
to detect the PAUSE rate matching ability of these PHYs, so we need to
use the Aquantia rather than the generic C45 driver. This needs
aqr107_read_status() -> aqr107_read_rate() to set phydev->rate_matching,
as well as the aqr107_get_rate_matching() method.
I am a bit unsure about the naming convention in the driver. Since
AQR107 is a Gen2 PHY, I assume all functions prefixed with "aqr107_"
rather than "aqr_" mean Gen2+ features. So I've reused this naming
convention.
I've tested PHY "SGMII" statistics as well as the .link_change_notify
method, which prints:
Aquantia AQR412 mdio_mux-0.4:00: Link partner is Aquantia PHY, FW 4.3, fast-retrain downshift advertised, fast reframe advertised
Tested SERDES protocols are usxgmii and 2500base-x (the latter with
PAUSE rate matching). Tested link modes are 100/1000/2500 Base-T
(with Aquantia link partner and with other link partners). No notable
events observed.
The placement of these PHY IDs in the driver is right before AQR113C,
a Gen4 PHY.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
1) Fix sparse warning in the new nft_inner expression, reported
by Jakub Kicinski.
2) Incorrect vlan header check in nft_inner, from Peng Wu.
3) Two patches to pass reset boolean to expression dump operation,
in preparation for allowing to reset stateful expressions in rules.
This adds a new NFT_MSG_GETRULE_RESET command. From Phil Sutter.
4) Inconsistent indentation in nft_fib, from Jiapeng Chong.
5) Speed up siphash calculation in conntrack, from Florian Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: conntrack: use siphash_4u64
netfilter: rpfilter/fib: clean up some inconsistent indenting
netfilter: nf_tables: Introduce NFT_MSG_GETRULE_RESET
netfilter: nf_tables: Extend nft_expr_ops::dump callback parameters
netfilter: nft_inner: fix return value check in nft_inner_parse_l2l3()
netfilter: nft_payload: use __be16 to store gre version
====================
Link: https://lore.kernel.org/r/20221115095922.139954-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The NFP documentation is updated to include information about Corigine,
and the new NFP3800 chips. The 'Acquiring Firmware' section is updated
with new information about where to find firmware.
Two new sections are added to expand the coverage of the documentation.
The new sections include:
- Devlink Info
- Configure Device
Signed-off-by: Walter Heymans <walter.heymans@corigine.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20221115090834.738645-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Felix Fietkau says:
====================
mtk_eth_soc rx vlan offload improvement + dsa hardware untag support
This series improves rx vlan offloading on mtk_eth_soc and extends it to
support hardware DSA untagging where possible.
This improves performance by avoiding calls into the DSA tag driver receive
function, including mangling of skb->data.
This is split out of a previous series, which added other fixes and
multiqueue support
====================
Link: https://lore.kernel.org/r/20221114124214.58199-1-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- pass the tag to DSA via metadata dst
- disabled on 7986 for now, since it's not working yet
- disabled if a MAC is enabled that does not use DSA
This improves performance by bypassing the DSA tag driver and avoiding extra
skb data mangling
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Keep the vlan rx offload feature in sync across all netdevs belonging to the
device, since the feature is global and can't be turned off per MAC
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the id from the DMA descriptor instead of hardcoding 802.1q
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a metadata dst is present with the type METADATA_HW_PORT_MUX on a dsa cpu
port netdev, assume that it carries the port number and that there is no DSA
tag present in the skb data.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch fixes a frame size warning, reported by kernel test robot.
>> net/dcb/dcbnl.c:1230:1: warning: the frame size of 1244 bytes is
>> larger than 1024 bytes [-Wframe-larger-than=]
The getapptrust part of dcbnl_ieee_fill is moved to a separate function,
and the selector array is now dynamically allocated, instead of stack
allocated.
Tested on microchip sparx5 driver.
Fixes: 6182d5875c ("net: dcb: add new apptrust attribute")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://lore.kernel.org/r/20221114092950.2490451-1-daniel.machon@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This function is used for every packet, siphash_4u64 is noticeably faster
than using local buffer + siphash:
Before:
1.23% kpktgend_0 [kernel.vmlinux] [k] __siphash_unaligned
0.14% kpktgend_0 [nf_conntrack] [k] hash_conntrack_raw
After:
0.79% kpktgend_0 [kernel.vmlinux] [k] siphash_4u64
0.15% kpktgend_0 [nf_conntrack] [k] hash_conntrack_raw
In the pktgen test this gives about ~2.4% performance improvement.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Analogous to NFT_MSG_GETOBJ_RESET, but for rules: Reset stateful
expressions like counters or quotas. The latter two are the only
consumers, adjust their 'dump' callbacks to respect the parameter
introduced earlier.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add a 'reset' flag just like with nft_object_ops::dump. This will be
useful to reset "anonymous stateful objects", e.g. simple rule counters.
No functional change intended.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The SYN flood message prints the listening port number, but with many
processes bound to the same port on different IPs, it's impossible to
tell which socket is the problem.
Add the listen IP address to the SYN flood message.
For IPv6 use "[IP]:port" as per RFC-5952 and to provide ease of
copy-paste to "ss" filters. For IPv4 use "IP:port" to match.
Each protcol's "any" address and a host address now look like:
Possible SYN flooding on port 0.0.0.0:9001.
Possible SYN flooding on port 127.0.0.1:9001.
Possible SYN flooding on port [::]:9001.
Possible SYN flooding on port [fc00::1]:9001.
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Link: https://lore.kernel.org/r/4fedab7ce54a389aeadbdc639f6b4f4988e9d2d7.1668386107.git.jamie.bainbridge@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Thomas Gleixner says:
====================
genirq/msi: Treewide cleanup of pointless linux/msi.h includes
While working on per device MSI domains I noticed that quite some files
include linux/msi.h just because.
The top level comment in the header file clearly says:
Regular device drivers have no business with any of these functions....
and actually none of the drivers needs anything from msi.h.
====================
Link: https://lore.kernel.org/r/20221113201935.776707081@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nothing in these files needs anything from linux/msi.h
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: oss-drivers@corigine.com
Acked-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nothing in these file needs anything from linux/msi.h
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If CONFIG_PTP_1588_CLOCK_OPTIONAL=m and CONFIG_RENESAS_ETHER_SWITCH=y,
the following build error happened:
aarch64-linux-ld: DWARF error: could not find abbrev number 60
drivers/net/ethernet/renesas/rswitch.o: in function `rswitch_get_ts_info':
rswitch.c:(.text+0x408): undefined reference to `ptp_clock_index'
aarch64-linux-ld: DWARF error: could not find abbrev number 1190123
drivers/net/ethernet/renesas/rcar_gen4_ptp.o: in function `rcar_gen4_ptp_register':
rcar_gen4_ptp.c:(.text+0x4dc): undefined reference to `ptp_clock_register'
aarch64-linux-ld: drivers/net/ethernet/renesas/rcar_gen4_ptp.o: in function `rcar_gen4_ptp_unregister':
rcar_gen4_ptp.c:(.text+0x584): undefined reference to `ptp_clock_unregister'
To fix the issue, add "depends on PTP_1588_CLOCK_OPTIONAL" into the
Kconfig.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6c6fa1a00a ("net: ethernet: renesas: rswitch: Add R-Car Gen4 gPTP support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20221110012720.3552060-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Misc updates to mlx5 driver
1) Support enhanced CQE compression, on ConnectX6-Dx
Reduce irq rate, cpu utilization and latency.
2) Connection tracking: Optimize the pre_ct table lookup for rules
installed on chain 0.
3) implement ethtool get_link_ext_stats for PHY down events
4) Expose device vhca_id to debugfs
5) misc cleanups and trivial changes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmNvc2QACgkQSD+KveBX
+j4DuggAiKEu7Imu94k+zXhm/n7Ykb8c1VIQVT9d9+lkyLaRVt5i7q6OpKtbRl4X
k5JMK0+xxXZ6lN/Du+iC3hwAxTayVOQn1KoQFVA85aAOBfd8fS4o7hMZ+gEAeaOy
qh34sUGPX5YzALN5zhIdk97h1kYvjbjX8CujyluBR9TR9564m4e9oJzqBPC1otab
3YHqeCiP0P8TEclUbiKgkCxvB1JgnzXUnu/u74O6nmzB51gqr1gAZWIUE5y7uuGD
WjD/1x62h5kr1xN1TtItKJQWVi1QGXsgiYbB13pNvDCpEMM2ZioEp9GDhWjOLQyh
gYHm3Bne8YaV4dVf0lr/7ijTMSwJjQ==
=BBj5
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2022-11-12' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2022-11-12
Misc updates to mlx5 driver
1) Support enhanced CQE compression, on ConnectX6-Dx
Reduce irq rate, cpu utilization and latency.
2) Connection tracking: Optimize the pre_ct table lookup for rules
installed on chain 0.
3) implement ethtool get_link_ext_stats for PHY down events
4) Expose device vhca_id to debugfs
5) misc cleanups and trivial changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Added xdp and page pool statistics.
In order to make the implementation simple and compatible, the patch
uses the 32bit integer to record the XDP statistics.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steen Hegelund says:
====================
net: Add support for sorted VCAP rules in Sparx5
This provides support for adding Sparx5 VCAP rules in sorted order, VCAP
rule counters and TC filter matching on ARP frames.
It builds on top of the initial IS2 VCAP support found in these series:
https://lore.kernel.org/all/20221020130904.1215072-1-steen.hegelund@microchip.com/https://lore.kernel.org/all/20221109114116.3612477-1-steen.hegelund@microchip.com/
Functionality
=============
When a new VCAP rule is added the driver will now ensure that the rule is
inserted in sorted order, and when a rule is removed, the remaining rules
will be moved to keep the sorted order and remove any gaps in the VCAP
address space.
A VCAP rule is ordered using these 3 values:
- Rule size: the count of VCAP addresses used by the rule. The largest
rule have highest priority
- Rule User: The rules are ordered by the user enumeration
- Priority: The priority provided in the flower filter. The lowest value
has the highest priority.
A VCAP instance may contain the counter as part of the VCAP cache area, and
this counter may be one or more bits in width. This type of counter
automatically increments its value when the rule is hit.
Other VCAP instances have a dedicated counter area outside of the VCAP and
in this case the rule must contain the counter id to be able to locate the
counter value and cause the counter to be incremented. In this case there
must also be a VCAP rule action that sets the counter id.
The Sparx5 IS2 VCAP uses a dedicated counter area with 32bit counters.
This series adds support for getting VCAP rule counters and provide these
via the TC statistic interface.
This only support packet counters, not byte counters.
Finally the series adds support for the ARP frame dissector and configures
the Sparx5 IS2 VCAP to generate the ARP keyset when ARP traffic is
received.
Delivery:
=========
This is current plan for delivering the full VCAP feature set of Sparx5:
- DebugFS support for inspecting rules
- TC protocol all support
- Sparx5 IS0 VCAP support
- TC policer and drop action support (depends on the Sparx5 QoS support
upstreamed separately)
- Sparx5 ES0 VCAP support
- TC flower template support
- TC matchall filter support for mirroring and policing ports
- TC flower filter mirror action support
- Sparx5 ES2 VCAP support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This tests the insert, move and deleting of rules and checks that the
unused VCAP addresses are initialized correctly.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides flower filter packet statistics (bytes are not supported) via
the dedicated IS2 counter feature.
All rules having the same TC cookie will contribute to the packet
statistics for the filter as they are considered to be part of the same TC
flower filter.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds API methods to set and get a rule counter.
A VCAP instance may contain the counter as part of the VCAP cache area, and
this counter may be one or more bits in width. This type of counter
automatically increments it value when the rule is hit.
Other VCAP instances have a dedicated counter area outside of the VCAP and
in this case the rule must contain the counter id to be able to locate the
counter value. In this case there must also be a rule action that updates
the counter using the rule id when the rule is hit.
The Sparx5 IS2 VCAP uses a dedicated counter area.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a sorting criteria to rule insertion and deletion.
The criteria is (in the listed order):
- Rule size (largest size first)
- User (based on an enumerated user value)
- Priority (highest priority first, aka lowest value)
When a rule is deleted the other rules may need to be moved to fill the gap
to use the available VCAP address space in the best possible way.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This add support for Sparx5 for dissecting TC ARP flower filter keys and
sets up the Sparx5 IS2 VCAP to generate the ARP keyset for ARP frames.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a new flow_rule_match_arp function that allows drivers
to be able to dissect ARP frames.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of 'st->state' has been verified as "TCP_SEQ_STATE_LISTENING",
it's unnecessary to assign TCP_SEQ_STATE_LISTENING to it, so we can remove it.
Signed-off-by: xu xin <xu.xin16@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nick Child says:
====================
ibmvnic: Introduce affinity hint support
This is a patchset to do 3 things to improve ibmvnic performance:
1. Assign affinity hints to ibmvnic queue irq's
2. Update affinity hints on cpu hotplug events
3. Introduce transmit packet steering (XPS)
NOTE: If irqbalance is running, you need to stop it from overriding
our affinity hints. To do this you can do one of:
- systemctl stop irqbalance
- ban the ibmvnic module irqs
- you must have the latest irqbalance v9.2, the banmod argument was broken before this
- in /etc/sysconfig/irqbalance -> IRQBALANCE_ARGS="--banmod=ibmvnic"
- systemctl restart irqbalance
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Transmit Packet Steering (XPS) maps cpu numbers to transmit
queues. By running the same connection on the same set of cpu's,
contention for the queue and cache miss rate can be minimized.
When assigning a cpu mask for a tranmit queues irq number, assign
the same cpu mask as the set of cpu's that XPS should use for that
queue.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Rick Lindsley <ricklind@linux.ibm.com>
Reviewed-by: Haren Myneni <haren@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CPU's are added and removed, ibmvnic devices will reassign
hint values. Introduce a new cpu hotplug state CPUHP_IBMVNIC_DEAD
to signal to ibmvnic devices that the CPU has been removed and it
is time to reset affinity hint assignments. On the other hand,
when CPU's are being added, add a state instance to
CPUHP_AP_ONLINE_DYN which will trigger a reassignment of affinity
hints once the new CPU's are online. This implementation is based
on the virtio_net driver.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Rick Lindsley <ricklind@linux.ibm.com>
Reviewed-by: Haren Myneni <haren@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign affinity hints to ibmvnic device queue interrupts.
Affinity hints are assigned and removed during sub-crq init and
teardown, respectively. This update should improve latency if
utilized as interrupt lines and processing are more equally
distributed among CPU's. This implementation is based on the
virtio_net driver.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Rick Lindsley <ricklind@linux.ibm.com>
Reviewed-by: Haren Myneni <haren@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 2 virtchnl msgs:
VIRTCHNL_OP_SET_RSS_HENA
VIRTCHNL_OP_GET_RSS_HENA_CAPS
The first one allows VFs to clear all previously programmed
RSS configuration and customize it. The second one returns
the RSS HENA bits allowed by the hardware.
Introduce ice_err_to_virt_err which converts kernel
specific errors to virtchnl errors.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error handling in tun_get_user is very scattered.
This patch unifies error handling, reduces duplication of code, and
makes the logic clearer.
Signed-off-by: Chuang Wang <nashuiliang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ethtool_op get_link_ext_stats for PHY down events
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
The pre_ct table realizes in hardware the act_ct cache logic, bypassing
the CT table if the ct state was already set by a previous ct lookup.
As such, the pre_ct table will always miss for chain 0 filters.
Optimize the pre_ct table lookup for rules installed on chain 0.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
A single async context object is sufficient to wait for the completions
of many callbacks. Switch to using one instance per a bulk of commands.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Waiting on a completion object for each callback before cleaning up their
async contexts is not necessary, as this is already implied in the
mlx5_cmd_cleanup_async_ctx() API.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Work field in struct mlx5e_async_ctx is not used. Remove it.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The case where the packet is not offloaded and needs to be restored
to slow path and couldn't find expected tunnel information should not
dump a call trace to the user. there is a debug call.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Up until now, return value of update_rx was ignored. Therefore, flow
continues even if it fails. Add error flow in case of update_rx fails in
mlx5e_open_locked, mlx5i_open and mlx5i_pkey_open.
Signed-off-by: Guy Truzman <gtruzman@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Params info print was meant to be printed on load.
With time, new calls to mlx5e_init_rq_type_params and
mlx5e_build_rq_params were added, mistakenly printing
the params once again.
Move the print to were it belongs, in mlx5e_probe.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
CQE compression feature improves performance by reducing PCI bandwidth
bottleneck on CQEs write.
Enhanced CQE compression introduced in ConnectX-6 and it aims to reduce
CPU utilization of SW side packets decompression by eliminating the
need to rewrite ownership bit, which is likely to cost a cache-miss, is
replaced by validity byte handled solely by HW.
Another advantage of the enhanced feature is that session packets are
available to SW as soon as a single CQE slot is filled, instead of
waiting for session to close, this improves packet latency from NIC to
host.
Performance:
Following are tested scenarios and reults comparing basic and enahnced
CQE compression.
setup: IXIA 100GbE connected directly to port 0 and port 1 of
ConnectX-6 Dx 100GbE dual port.
Case #1 RX only, single flow goes to single queue:
IRQ rate reduced by ~ 30%, CPU utilization improved by 2%.
Case #2 IP forwarding from port 1 to port 0 single flow goes to
single queue:
Avg latency improved from 60us to 21us, frame loss improved from 0.5% to 0.0%.
Case #3 IP forwarding from port 1 to port 0 Max Throughput IXIA sends
100%, 8192 UDP flows, goes to 24 queues:
Enhanced is equal or slightly better than basic.
Testing the basic compression feature with this patch shows there is
no perfrormance degradation of the basic compression feature.
Signed-off-by: Ofer Levi <oferle@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Replace the min/max operations with a single clamp.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This is never used, and probably something that was intended to be used
before per-protocol hash tables were chosen instead.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
hca_id is an identifier of an mlx5_core instance within the hardware.
This identifier may be required for troubleshooting.
Expose it to debugfs.
Example:
$ cat /sys/kernel/debug/mlx5/mlx5_core.sf.2/vhca_id
0x12
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Before this patch, devlink traps are registered only on full driver
probe and unregistered on driver removal. As devlink traps are not
usable once driver functionality is unloaded, it should be unrgeistered
also on flows that unload the driver and then registered when loaded
back, e.g. devlink reload flow.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
There is a spelling mistake in an error message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
There is no need for the warn if entry already removed.
Use debug print like in the update flow.
Also update the messages so user can identify if the it's
from the update flow or remove flow.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Use try_cmpxchg() (instead of cmpxchg()) in a more readable way.
oval = smp_load_acquire(&sk->sk_tsq_flags);
do {
...
} while (!try_cmpxchg(&sk->sk_tsq_flags, &oval, nval));
Reduce indentation level.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221110190239.3531280-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
