Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Xiaolei Li <xiaolei.li@mediatek.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Harvey Hunt <harveyhuntnexus@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Notes:
"pw 947037"
Return -ENOTSUPP instead of -1 from ->chip_init_tail() before migrating
this driver to use nand_scan() and transform this function to be a
callback run by the core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Also change the unused "struct device *dev" parameter of the driver
structure into a platform device to reuse it in the ->attach_chip()
hook.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
We don't use the GPIO API in this driver, let's just remove the
<linux/gpio.h> inclusion.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
gpio/consumer.h defines everything we need, and it's clearly stated in
gpio.h that GPIO consumers should directly stop including gpio.h if they
can.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit ddd5ed3a90 ("mtd: rawnand: sunxi: Remove support for
GPIO-based Ready/Busy polling") removed GPIO-based RB polling. We no
longer need to include gpio headers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
GPIO consumers should no longer include <linux/gpio.h>, and instead
include <linux/gpio/consumer.h>.
Also, explicitly include <include/io.h> since it seems to be missing
after switching to <linux/gpio/consumer.h>.
This fixes a build error when selecting the driver without selecting
GPIOLIB, which can happen when COMPILE_TEST=y.
Fixes: 6968e07e81 ("mtd: rawnand: jz4740: Allow selection of this driver when COMPILE_TEST=y")
Reported-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In order to remove the limitation that forbids dynamic allocation in
nand_scan_ident(), we must create a path that will be the same for all
controller drivers. The idea is to use nand_scan() instead of the widely
used nand_scan_ident()/nand_scan_tail() couple. In order to achieve
this, controller drivers will need to adjust some parameters between
these two functions depending on the NAND chip wired on them.
This takes the form of two new hooks (->{attach,detach}_chip()) that are
placed in a new nand_controller_ops structure, which is then attached
to the nand_controller object at driver initialization time.
->attach_chip() is called between nand_scan_ident() and
nand_scan_tail(), and ->detach_chip() is called in the error path of
nand_scan() and in nand_cleanup().
Note that some NAND controller drivers don't have a dedicated
nand_controller object and instead rely on the default/dummy one
embedded in nand_chip. If you're in this case and still want to
initialize the controller ops, you'll have to manipulate
chip->dummy_controller directly.
Last but not least, it's worth mentioning that we plan to move some of
the controller related hooks placed in nand_chip into
nand_controller_ops to make the separation between NAND chip and NAND
controller methods clearer.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
In the raw NAND core, a NAND chip is described by a nand_chip structure,
while a NAND controller is described with a nand_hw_control structure
which is not very meaningful.
Rename this structure nand_controller.
As the structure gets renamed, it is logical to also rename the core
function initializing it from nand_hw_control_init() to
nand_controller_init().
Lastly, the 'hwcontrol' entry of the nand_chip structure is not
meaningful neither while it has the role of fallback when no controller
structure is provided by the driver (the controller driver is dumb and
can only control a single chip). Thus, it is renamed dummy_controller.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Commit 260e89a6e0 ("mtd: core: tone down suggestion that dev.parent
should be set") removed the only user of caller_is_module() but forgot
to remove the definition itself. Let's remove it now.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
All of the code in the probe path assumes ->sets != NULL and
->nrsets > 0. Error out if that's not the case to avoid dereferencing a
NULL pointer.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
A report from Colin Ian King pointed a CoverityScan issue where error
values on these helpers where not checked in the drivers. These
helpers can error out only in case of a software bug in driver code,
not because of a runtime/hardware error. Hence, let's WARN_ON() in this
case and return 0 which is harmless anyway.
Fixes: 8878b126df ("mtd: nand: add ->exec_op() implementation")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Make sure __LINUX_ARM_ARCH__ is defined before testing its value.
This is needed if we want to allow selection of this driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Include linux/sizes.h instead of asm/sizes.h to make code completely
arch independent.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We currently don't store the on-die ECC state (enabled/disabled) which
might force us to re-disable the engine even if it's already been
disabled after we've read the page in raw mode to count the actual
number of bitflips.
Add an "enabled" field to struct micron_on_die_ecc to keep track of the
ECC state.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some chips have their on-die ECC forcibly enabled, there's no point in
trying to enable/disable the ECC engine in that case.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The MT29F2Gxxx chips with 4bits/512byte on-die ECC let us know when
some bitflips were corrected by the on-die ECC, but they do not report
the actual number of bitflips that were present in the data+ECC chunk.
We initially decided to always return ecc->strength to avoid re-reading
the page in raw mode + comparing it to the corrected buffer to extract
the real number of bitflips, but this forces UBI to move data around as
soon as one bitflip is present in a page.
This not only wears the NAND out faster, but also degrades
performances, since reading a full PEB + writing it back to a different
PEB + erasing the old one is much more expensive than re-reading the
faulty page in raw mode and comparing it to the corrected buffer.
In most cases, the actual number of bitflips does not exceed the
bitflips threshold, and UBI won't have to move data around. Otherwise,
we can assume the time spent re-reading the page and doing the
comparison is negligible compared to the time UBI spends moving a full
PEB to another PEB.
Note that this logic is not applied to chips with 8bits/512byte on-die
ECC, because those chips provide fine-grained information (the maximum
error is 1 bit, and it will not force UBI to move blocks around at the
first bitflip).
Suggested-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some Micron NAND chips have on-die ECC forceably enabled. Allow such
chips to be used as long as the controller has set chip->ecc.mode to
NAND_ECC_ON_DIE.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some implementations simply can't disable their ECC engine. Expose
helpers returning -ENOTSUPP so that the caller knows that raw accesses
are not supported instead of silently falling back to non-raw
accessors.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Micron MT29F1G08ABAFAWP-ITE:F supports an on-die ECC with 8 bits
per 512 bytes. Add support for this combination.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Basing the "mandatory on-die" detection on ID byte 2 does not work,
because Micron has plenty of NANDs using the same device ID code, and
not all of them have forcibly enabled on-die ECC.
Since the "Array Operation" feature does not provide the "ECC
enabled/disabled" bit when the ECC can't be disabled, let's try to use
the "ECC enabled/disabled" bit in the READ_ID bytes.
It seems that this bit is dynamically updated on NANDs where on-die ECC
can freely be enabled/disabled, so let's hope it stays at one when we
have a NAND with on-die ECC forcibly enabled.
Fixes: 51f3b3970a8c ("mtd: rawnand: micron: detect forced on-die ECC")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
chip->read_buf is left unassigned since commit 4da712e702 ("mtd: nand:
fsmc: use ->exec_op()"), leading to a NULL pointer dereference when it's
called from fsmc_read_page_hwecc(). Fix that by using the appropriate
helper to read data out of the NAND.
Fixes: 4da712e702 ("mtd: nand: fsmc: use ->exec_op()")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Compile-testing this driver on x86 caused a link error:
ERROR: "__phys_to_dma" [drivers/mtd/nand/raw/qcom_nandc.ko] undefined!
The problem here is that the driver attempts to convert the physical
address into the DMA controller as a dma_addr_t and calls phys_to_dma()
to do the conversion.
The correct way to do the conversion is using the dma mapping interfaces.
Fixes: c76b78d8ec ("mtd: nand: Qualcomm NAND controller driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The Tegra driver currently only support a single chip select, hence
check boundaries accordingly. This fixes a off by one issue catched
with Smatch:
drivers/mtd/nand/raw/tegra_nand.c:476 tegra_nand_select_chip()
warn: array off by one? 'nand->cs[die_nr]'
Also warn in case the stack asks for a chip select we currently do
not support.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some timings like tBERS (block erase time), tCCs (change column setup
time), tPROG (page program time) and tR (page read time) are derived
from the ONFI parameter page. They are set in the SDR interface only
if the chip is ONFI compliant.
It makes these timings unreliable and prevent the driver to use one of
these four values with a non-ONFI chip.
Fix this situation by taking the highest possible value (or a default
one) value for each missing timing (stored as unsigned 16-bit entries in
the parameter page).
This makes tBERS and tPROG being ~65ms while typical values are at most
a few milliseconds. As these are timeouts, it is not impacting at all
the performances in nominal use.
tR maximum time and tCCS minimum time (delay to wait after a change
column) are set, according to the ONFI specification, to default 'slow'
values; respectively 200us and 500ns.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If driver doesn't specify parsers it can use that little helper.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If driver doesn't specify parsers it can use that little helper.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We already have a dependency on BCMA_NFLASH, which in turn depends on
BCMA, but since BCMA is a tristate option and BCMA_NFLASH is bool,
we can run into an invalid configuration with MTD_NAND_BCM47XXNFLASH=y
and BCMA=m:
drivers/mtd/nand/raw/bcm47xxnflash/ops_bcm4706.o: In function `bcm47xxnflash_ops_bcm4706_init':
ops_bcm4706.c:(.text+0x790): undefined reference to `bcma_chipco_pll_read'
Adding the dependency here forces MTD_NAND_BCM47XXNFLASH to only be
configured =m here so it can link against the BCMA driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In jz_nand_detect_bank(), chipnr is a size_t argument. Use %zu instead
of %i when printing it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This MACH_JZ4780 dependency is taken care of by JZ4780_NEMC, no need
to repeat it here.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having MACH_JZ4740 enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This way we will be able to compile the jz4740_nand driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having SOC_TX4938 or SOC_TX4939
enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This way we will be able to compile the ndfmc driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes maintainers' life easier by allowing them to compile-test
this driver without having FSL_SOC, ARCH_LAYERSCAPE or SOC_LS1021A
enabled.
We also need to add a dependency on HAS_IOMEM to make sure the
driver compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The local eccstat_regs variable in fsl_ifc_run_command() is missing an
__iomem specifier, and sparce complains about that.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having PLAT_SPEAR, ARCH_NOMADIK,
ARCH_U8500 or MACH_U300 enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
uintptr_t should be used when casting a pointer to an unsigned int so
that the code compiles without warnings even on 64-bit architectures.
This is needed if we want to allow selection of this driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We want to allow this driver to be selected when COMPILE_TEST=y, this
means the driver can be compiled for any arch, including MIPS. When
compiling this driver for MIPS, we end up with a collision on the 'PC'
macro definition (also defined in arch/mips/include/asm/ptrace.h).
Prefix the fsmc one with FSMC_ to avoid this problem.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_SUNXI enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
