The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Some trivial improvements on the returning value of the
functions:
- remove unnecessary goto labels that just return, return
immediately, instead.
- do not initialize when not needed.
- return the value from the calling function that fails instead
of politically choosing -EINVAL.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
val might become 7 in which case stime[7] (array of length 7) would be
accessed during the scnprintf call later and that will cause issues.
Obviously, string concatenation is not intended here so just a comma needs
to be added to fix the issue.
Fixes: 98a2766493 ("power_supply: Add new lp8788 charger driver")
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The custom CPCAP PMIC used on Motorola phones such as Droid 4 has a
USB battery charger. It can optionally also have a companion chip that
is used for wireless charging.
The charger on CPCAP also can feed VBUS for the USB host mode. This
can be handled by the existing kernel phy_companion interface.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add support for monitoring an extcon device with USB SDP/CDP/DCP and HOST
cables and adjust ilimit and enable/disable the 5V boost converter
accordingly. This is necessary on systems where the PSEL pin is hardwired
high and ILIM needs to be set by software based on the detected charger
type, as well as on systems where the 5V boost converter is used, as
that always needs to be enabled from software.
Cc: Liam Breck <kernel@networkimprov.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The bq24192 and bq24192i are mostly identical to the bq24190, TI even
published a single datasheet for all 3 of them. The difference
between the bq24190 and bq24192[i] is the way charger-type detection
is done, the bq24190 is to be directly connected to the USB a/b lines,
where as the the bq24192[i] has a gpio which should be driven high/low
externally depending on the type of charger connected, from a register
level access pov there is no difference.
The differences between the bq24192 and bq24192i are:
1) Lower default charge rate on the bq24192i
2) Pre-charge-current can be max 640 mA on the bq24192i
On x86/ACPI systems the code which instantiates the i2c client may not
know the exact variant being used, so instead of coding the model-id
in the i2c_id struct and bailing if it does not match, check the reported
model-id matches one of the supported variants.
This commit only adds support for the bq24192i as I don't
have a bq24192 to test with, adding support for the bq24192 should
be as simple as also accepting its model-id in the model-id test.
Cc: Liam Breck <kernel@networkimprov.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The i2c-core already maps of irqs before calling the driver's probe
function and there are no in tree users of
bq24190_platform_data->gpio_int.
Remove the redundant custom irq-mapping code and just use client->irq.
Cc: Liam Breck <kernel@networkimprov.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Without CONFIG_PM, we get a harmless warning:
drivers/power/supply/bq24190_charger.c:1514:12: error: 'bq24190_runtime_resume' defined but not used [-Werror=unused-function]
drivers/power/supply/bq24190_charger.c:1501:12: error: 'bq24190_runtime_suspend' defined but not used [-Werror=unused-function]
To avoid the warning, we can mark all four PM functions as __maybe_unused,
which also lets us remove the incorrect #ifdef.
Fixes: 3d8090cba638 ("power: bq24190_charger: Check the interrupt status on resume")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch fixes 4 checkpatch.pl errors on lines 433 to 436:
ERROR: code indent should use tabs where possible
Signed-off-by: Munir Contractor <munircontractor@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Since index is always 0, replace gpiod_get_index() by gpiod_get().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The Gemini (SL3516) SoC has a special power controller block
that only deal with shutting down the system.
If you do not register a driver and activate the block, the
power button on the systems utilizing this SoC will do an
uncontrolled power cut, which is why it is important to have
a special poweroff driver.
The most basic functionality is to just shut down the system
by writing a special bit in the control register after the
system has reached pm_poweroff.
It also handles the poweroff from a button or other sources:
When the poweroff button is pressed, or a signal is sent to
poweroff from an infrared remote control, or when the RTC
fires a special alarm (!) the system emits an interrupt.
At this point, Linux must acknowledge the interrupt and
proceed to do an orderly shutdown of the system.
After adding this driver, pressing the poweroff button gives
this dmesg:
root@gemini:/
root@gemini:/ gemini-poweroff 4b000000.power-controller:
poweroff button pressed
calling shutdown scripts..
setting /dev/rtc0 from system time
unmounting file systems...
umount: tmpfs busy - remounted read-only
umount: can't unmount /: Invalid argument
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system poweroff
uhci_hcd 0000:00:09.1: HCRESET not completed yet!
uhci_hcd 0000:00:09.0: HCRESET not completed yet!
reboot: Power down
gemini-poweroff 4b000000.power-controller: Gemini power off
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Make the syscon-poweroff driver accept value and mask instead of
just value.
Prior to this patch, the property name for the value was 'mask'. If
only the mask property is defined on a node, maintain compatibility
by using it as the value.
Signed-off-by: Guy Shapiro <guy.shapiro@mobi-wize.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
We can get quite a few interrupts when the battery is trickle charging.
Let's enable PM runtime autosuspend to avoid constantly toggling device
driver PM runtime state.
Let's use a 600 ms timeout as that's how long the USB chager detection
might take.
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Some SoCs like omap3 can configure GPIO irqs to use Linux generic
dedicated wakeirq support. If the dedicated wakeirq is configured,
the SoC will use a always-on interrupt controller to produce wake-up
events.
If bq24190 is configured for dedicated wakeirq, we need to check the
interrupt status on PM runtime resume. This is because the Linux
generic wakeirq will call pm_runtime_resume() on the device on a
wakeirq. And as the bq24190 interrupt is falling edge sensitive
and only active for 250 us, there will be no device interrupt seen
by the runtime SoC IRQ controller.
Note that this can cause spurious interrupts on omap3 devices with
bq24190 connected to gpio banks 2 - 5 as there's a glitch on those
pins waking from off mode as listed in "Advisory 1.45". Devices
with this issue should not configure the optional wakeirq interrupt
in the dts file.
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Fix typos and add the following to the scripts/spelling.txt:
intialization||initialization
The "inintialization" in drivers/acpi/spcr.c is a different pattern but
I fixed it as well in this commit.
Link: http://lkml.kernel.org/r/1481573103-11329-16-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The X-Powers AXP20X and AXP22X PMICs expose the status of AC power
supply.
Moreover, the AXP20X can also expose the current current and voltage
values of the AC power supply.
This adds the driver which exposes the status of the AC power supply of
the AXP20X and AXP22X PMICs.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[removed unused elements from struct axp20x_ac_power]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The X-Powers AXP20X PMIC exposes the current current and voltage
measures via an internal ADC.
This adds the possibility to read IIO channels directly for processed
values rather than reading the registers and computing the value.
For backward compatibility purpose, if the IIO driver is not compiled,
this driver will fall back on previous behaviour which is direct
register readings.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
If the driver is built as a module, I2C module alias information is not
filled so the module won't be autoloaded. Export the I2C and OF devices
ID to the module by using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/power/supply/max14656_charger_detector.ko | grep alias
$
After this patch:
$ modinfo drivers/power/supply/max14656_charger_detector.ko | grep alias
alias: i2c:max14656
alias: of:N*T*Cmaxim,max14656C*
alias: of:N*T*Cmaxim,max14656
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
acpi_match_device can potentially return NULL, so it is prudent to
check if acpi_id is null before it is dereferenced. Add a check
and an error message to indicate the failure.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reading both fault and status registers and logging any fault should
take priority over handling status register update.
Fix by moving the status handling to later in interrupt routine.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Caching the fault register after a single I2C read may not keep an accurate
value.
Fix by doing two reads in irq_handle_thread() and using the cached value
elsewhere. If a safety timer fault later clears itself, we apparently don't get
an interrupt (INT), however other interrupts would refresh the register cache.
From the data sheet: "When a fault occurs, the charger device sends out INT
and keeps the fault state in REG09 until the host reads the fault register.
Before the host reads REG09 and all the faults are cleared, the charger
device would not send any INT upon new faults. In order to read the
current fault status, the host has to read REG09 two times consecutively.
The 1st reads fault register status from the last read [1] and the 2nd reads
the current fault register status."
[1] presumably a typo; should be "last fault"
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
We wrongly get uevents for bq24190-charger and bq24190-battery on every
register change.
Fix by checking the association with charger and battery before
emitting uevent(s).
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The device specific data is not fully initialized on
request_threaded_irq(). This may cause a crash when the IRQ handler
tries to reference them.
Fix the issue by installing IRQ handler at the end of the probe.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
pm_resume() does a register_reset() which clears charger host mode.
Fix by calling set_mode_host() after the reset.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The interrupt signal is TRIGGER_FALLING. This is is specified in the
data sheet PIN FUNCTIONS: "The INT pin sends active low, 256us
pulse to host to report charger device status and fault."
Also the direction can be seen in the data sheet Figure 37 "BQ24190
with D+/D- Detection and USB On-The-Go (OTG)" which shows a 10k
pull-up resistor installed for the sample configurations.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The added regulator dependency in the smbb driver causes build errors
when regulators are disabled, e.g. in randconfig build testing:
drivers/power/supply/qcom_smbb.o: In function `smbb_chg_otg_is_enabled':
qcom_smbb.c:(.text.smbb_chg_otg_is_enabled+0x18): undefined reference to `rdev_get_drvdata'
drivers/power/supply/qcom_smbb.o: In function `smbb_charger_probe':
qcom_smbb.c:(.text.smbb_charger_probe+0x410): undefined reference to `devm_regulator_register'
This adds a Kconfig dependency to avoid the link error.
Fixes: 61274eff0d ("power: supply: qcom_smbb: Add otg regulator for control of vbus")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
commit eacd8d09db ("power/reset: at91-reset: remove useless
at91_reset_platform_probe()") removed non DT probe support but forgot to
remove the now useless id_table. Do that now.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add samx7 support. It is lacking a few bits and needs a new reset function.
Signed-off-by: Szemző András <sza@esh.hu>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
drivers/power/supply/max14656_charger_detector.c:317:3-8:
No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Alexander Kurz <akurz@blala.de>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Simplify return logic to avoid unnecessary variable assignments.
These issues were detected using Coccinelle and the following semantic patch:
@@
local idexpression ret;
expression e;
@@
-ret =
+return
e;
-return ret;
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Simplify return logic to avoid unnecessary variable assignments.
These issues were detected using Coccinelle and the following semantic patch:
@@
local idexpression ret;
expression e;
@@
-ret =
+return
e;
-return ret;
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
LPDDR memories can only handle up to 400 uncontrolled power off. Ensure the
proper power off sequence is used before shutting down the platform.
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The MAX14656 USB charger detector, also known as "AL32" is used to detect
the presence and capabilities of attached USB chargers. The device is
attached via I2C plus one interrupt line to signalize events.
The device can be found in LG smartphones like LS665 and LS770, compatible
devices are present in 4th/5th generation Amazon Kindle readers referenced
in source code packages as "Maxim AL32".
The initial version of this driver has been extracted from LG source code
package LGLS665_Android_Lollipop_LS665ZV3, enriched with information from
the Kindle_src_4.1.3 source code package and adapted to the current power
class sysfs interface. Non-Standard Apple chargers which the device may
detect are mapped to the USB Battery Charging Specification Revision 1.2
class USB_DCP.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add a regulator to control the OTG chargepath switch. This
is used by USB code to control VBUS direction - out for host mode
on the OTG port, and in for charging mode.
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
[stephen.boyd@linaro.org: Fix supply name, constify ops, drop
machine.h and of_regulator.h includes]
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27520G4 chip definition to specifically match the
bq27520-G4 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27520G3 chip definition to specifically match the
bq27520-G3 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27520G2 chip definition to specifically match the
bq27520-G2 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27520G1 chip definition to specifically match the
bq27520-G1 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27510G3 chip definition to specifically match the
bq27510-G3 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Tested-by: Chris Lapa <chris@lapa.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27510G2 chip definition to specifically match the
bq27510-G2 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27510G1 chip definition to specifically match the
bq27510-G1 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27500 chip definition to specifically match the
bq27500/1 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The BQ2751X definition exists only to satisfy backwards compatibility.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The BQ2750X definition exists only to satisfy backwards compatibility.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Casting of_device_get_match_data return value to int causes warning on 64bit
architectures.
../drivers/power/supply/axp20x_usb_power.c: In function
'axp20x_usb_power_probe':
../drivers/power/supply/axp20x_usb_power.c:297:21: warning: cast from
pointer to integer of different size [-Wpointer-to-int-cast]
Fixes: 0dcc70ca86 ("power: supply: axp20x_usb_power: use of_device_id
data field instead of device_is_compatible")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
