commit 015c9cbcf0 upstream.
Due to a flaw in the hardware design, the GL9750 replay timer frequently
times out when ASPM is enabled. As a result, the warning messages will
often appear in the system log when the system accesses the GL9750
PCI config. Therefore, the replay timer timeout must be masked.
Fixes: d7133797e9 ("mmc: sdhci-pci-gli: A workaround to allow GL9750 to enter ASPM L1.2")
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kai-Heng Feng <kai.heng.geng@canonical.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231107095741.8832-2-victorshihgli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ab0c45d8a upstream.
For devices that support DASH, even DASH is disabled, there may still
exist a default firmware that will influence device behavior.
So driver needs to handle DASH for devices that support DASH, no
matter the DASH status is.
This patch also prepares for "fix network lost after resume on DASH
systems".
Fixes: ee7a1beb97 ("r8169:call "rtl8168_driver_start" "rtl8168_driver_stop" only when hardware dash function is enabled")
Cc: stable@vger.kernel.org
Signed-off-by: ChunHao Lin <hau@realtek.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20231109173400.4573-2-hau@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 868c3b95af upstream.
Device that support DASH may be reseted or powered off during suspend.
So driver needs to handle DASH during system suspend and resume. Or
DASH firmware will influence device behavior and causes network lost.
Fixes: b646d90053 ("r8169: magic.")
Cc: stable@vger.kernel.org
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: ChunHao Lin <hau@realtek.com>
Link: https://lore.kernel.org/r/20231109173400.4573-3-hau@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7cefbe5e1d upstream.
Running the mp_join selftest manually with the following command line:
./mptcp_join.sh -z -C
leads to some failures:
002 fastclose server test
# ...
rtx [fail] got 1 MP_RST[s] TX expected 0
# ...
rstrx [fail] got 1 MP_RST[s] RX expected 0
The problem is really in the wrong expectations for the RST checks
implied by the csum validation. Note that the same check is repeated
explicitly in the same test-case, with the correct expectation and
pass successfully.
Address the issue explicitly setting the correct expectation for
the failing checks.
Reported-by: Xiumei Mu <xmu@redhat.com>
Fixes: 6bf41020b7 ("selftests: mptcp: update and extend fastclose test-cases")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20231114-upstream-net-20231113-mptcp-misc-fixes-6-7-rc2-v1-5-7b9cd6a7b7f4@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8df220b292 upstream.
This patch adds the validity check for sending RM_ADDRs for userspace PM
in mptcp_pm_remove_addrs(), only send a RM_ADDR when the address is in the
anno_list or conn_list.
Fixes: 8b1c94da1e ("mptcp: only send RM_ADDR in nl_cmd_remove")
Cc: stable@vger.kernel.org
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20231114-upstream-net-20231113-mptcp-misc-fixes-6-7-rc2-v1-3-7b9cd6a7b7f4@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24948e3b7b upstream.
Objcg vectors attached to slab pages to store slab object ownership
information are allocated using gfp flags for the original slab
allocation. Depending on slab page order and the size of slab objects,
objcg vector can take several pages.
If the original allocation was done with the __GFP_NOFAIL flag, it
triggered a warning in the page allocation code. Indeed, order > 1 pages
should not been allocated with the __GFP_NOFAIL flag.
Fix this by simply dropping the __GFP_NOFAIL flag when allocating the
objcg vector. It effectively allows to skip the accounting of a single
slab object under a heavy memory pressure.
An alternative would be to implement the mechanism to fallback to order-0
allocations for accounting metadata, which is also not perfect because it
will increase performance penalty and memory footprint of the kernel
memory accounting under memory pressure.
Link: https://lkml.kernel.org/r/ZUp8ZFGxwmCx4ZFr@P9FQF9L96D.corp.robot.car
Signed-off-by: Roman Gushchin <roman.gushchin@linux.dev>
Reported-by: Christoph Lameter <cl@linux.com>
Closes: https://lkml.kernel.org/r/6b42243e-f197-600a-5d22-56bd728a5ad8@gentwo.org
Acked-by: Shakeel Butt <shakeelb@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a48d5bdc87 upstream.
While qualifiying the 6.4 release, the following warning was detected in
messages:
vmstat_refresh: nr_file_hugepages -15664
The warning is caused by the incorrect updating of the NR_FILE_THPS
counter in the function split_huge_page_to_list. The if case is checking
for folio_test_swapbacked, but the else case is missing the check for
folio_test_pmd_mappable. The other functions that manipulate the counter
like __filemap_add_folio and filemap_unaccount_folio have the
corresponding check.
I have a test case, which reproduces the problem. It can be found here:
https://github.com/sroeschus/testcase/blob/main/vmstat_refresh/madv.c
The test case reproduces on an XFS filesystem. Running the same test
case on a BTRFS filesystem does not reproduce the problem.
AFAIK version 6.1 until 6.6 are affected by this problem.
[akpm@linux-foundation.org: whitespace fix]
[shr@devkernel.io: test for folio_test_pmd_mappable()]
Link: https://lkml.kernel.org/r/20231108171517.2436103-1-shr@devkernel.io
Link: https://lkml.kernel.org/r/20231106181918.1091043-1-shr@devkernel.io
Signed-off-by: Stefan Roesch <shr@devkernel.io>
Co-debugged-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7133797e9 upstream.
When GL9750 enters ASPM L1 sub-states, it will stay at L1.1 and will not
enter L1.2. The workaround is to toggle PM state to allow GL9750 to enter
ASPM L1.2.
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20230912091710.7797-1-victorshihgli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8cb22bec14 upstream.
Instructions can write to x0, so we should simulate these instructions
normally.
Currently, the kernel hangs if an instruction who writes to x0 is
simulated.
Fixes: c22b0bcb1d ("riscv: Add kprobes supported")
Cc: stable@vger.kernel.org
Signed-off-by: Nam Cao <namcaov@gmail.com>
Reviewed-by: Charlie Jenkins <charlie@rivosinc.com>
Acked-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/20230829182500.61875-1-namcaov@gmail.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e59e5e2754 upstream.
The pt_level uses CONFIG_PGTABLE_LEVELS to display page table names.
But if page mode is downgraded from kernel cmdline or restricted by
the hardware in 64BIT, it will give a wrong name.
Like, using no4lvl for sv39, ptdump named the 1G-mapping as "PUD"
that should be "PGD":
0xffffffd840000000-0xffffffd900000000 0x00000000c0000000 3G PUD D A G . . W R V
So select "P4D/PUD" or "PGD" via pgtable_l5/4_enabled to correct it.
Fixes: e8a62cc26d ("riscv: Implement sv48 support")
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Song Shuai <suagrfillet@gmail.com>
Link: https://lore.kernel.org/r/20230712115740.943324-1-suagrfillet@gmail.com
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230830044129.11481-3-palmer@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87615e95f6 upstream.
The interrupt entries are expected to be in the .irqentry.text section.
For example, for kprobes to work properly, exception code cannot be
probed; this is ensured by blacklisting addresses in the .irqentry.text
section.
Fixes: 7db91e57a0 ("RISC-V: Task implementation")
Signed-off-by: Nam Cao <namcaov@gmail.com>
Link: https://lore.kernel.org/r/20230821145708.21270-1-namcaov@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd16ac404a upstream.
Actually it is a part of Conor's
commit aae538cd03 ("riscv: fix detection of toolchain
Zihintpause support").
It is looks like a merge issue. Samuel's
commit 0b1d60d6dd ("riscv: Fix build with
CONFIG_CC_OPTIMIZE_FOR_SIZE=y") do not base on Conor's commit and
revert to __riscv_zihintpause. So this patch can fix it.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Fixes: 3c349eacc5 ("Merge patch "riscv: Fix build with CONFIG_CC_OPTIMIZE_FOR_SIZE=y"")
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230802064215.31111-1-minda.chen@starfivetech.com
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71945968d8 upstream.
A recent change to the optimization pipeline in LLVM reveals some
fragility around the inlining of LoongArch's __percpu functions, which
manifests as a BUILD_BUG() failure:
In file included from kernel/sched/build_policy.c:17:
In file included from include/linux/sched/cputime.h:5:
In file included from include/linux/sched/signal.h:5:
In file included from include/linux/rculist.h:11:
In file included from include/linux/rcupdate.h:26:
In file included from include/linux/irqflags.h:18:
arch/loongarch/include/asm/percpu.h:97:3: error: call to '__compiletime_assert_51' declared with 'error' attribute: BUILD_BUG failed
97 | BUILD_BUG();
| ^
include/linux/build_bug.h:59:21: note: expanded from macro 'BUILD_BUG'
59 | #define BUILD_BUG() BUILD_BUG_ON_MSG(1, "BUILD_BUG failed")
| ^
include/linux/build_bug.h:39:37: note: expanded from macro 'BUILD_BUG_ON_MSG'
39 | #define BUILD_BUG_ON_MSG(cond, msg) compiletime_assert(!(cond), msg)
| ^
include/linux/compiler_types.h:425:2: note: expanded from macro 'compiletime_assert'
425 | _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
| ^
include/linux/compiler_types.h:413:2: note: expanded from macro '_compiletime_assert'
413 | __compiletime_assert(condition, msg, prefix, suffix)
| ^
include/linux/compiler_types.h:406:4: note: expanded from macro '__compiletime_assert'
406 | prefix ## suffix(); \
| ^
<scratch space>:86:1: note: expanded from here
86 | __compiletime_assert_51
| ^
1 error generated.
If these functions are not inlined (which the compiler is free to do
even with functions marked with the standard 'inline' keyword), the
BUILD_BUG() in the default case cannot be eliminated since the compiler
cannot prove it is never used, resulting in a build failure due to the
error attribute.
Mark these functions as __always_inline to guarantee inlining so that
the BUILD_BUG() only triggers when the default case genuinely cannot be
eliminated due to an unexpected size.
Cc: <stable@vger.kernel.org>
Closes: https://github.com/ClangBuiltLinux/linux/issues/1955
Fixes: 46859ac8af ("LoongArch: Add multi-processor (SMP) support")
Link: 1a2e77cf9e
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49cecd8628 upstream.
When inserting a DRC-cached response into the reply buffer, ensure
that the reply buffer's xdr_stream is updated properly. Otherwise
the server will send a garbage response.
Cc: stable@vger.kernel.org # v6.3+
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Tested-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc1b5acb40 upstream.
seq_release should be called to free the allocated seq_file
Cc: stable@vger.kernel.org # v5.3+
Signed-off-by: Mahmoud Adam <mngyadam@amazon.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Fixes: 78599c42ae ("nfsd4: add file to display list of client's opens")
Reviewed-by: NeilBrown <neilb@suse.de>
Tested-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28f07f2ab4 upstream.
The commit 5721d4e5a9 enhanced dm-verity, so that it can verify blocks
from tasklets rather than from workqueues. This reportedly improves
performance significantly.
However, dm-verity was using the flag CRYPTO_TFM_REQ_MAY_SLEEP from
tasklets which resulted in warnings about sleeping function being called
from non-sleeping context.
BUG: sleeping function called from invalid context at crypto/internal.h:206
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 14, name: ksoftirqd/0
preempt_count: 100, expected: 0
RCU nest depth: 0, expected: 0
CPU: 0 PID: 14 Comm: ksoftirqd/0 Tainted: G W 6.7.0-rc1 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x32/0x50
__might_resched+0x110/0x160
crypto_hash_walk_done+0x54/0xb0
shash_ahash_update+0x51/0x60
verity_hash_update.isra.0+0x4a/0x130 [dm_verity]
verity_verify_io+0x165/0x550 [dm_verity]
? free_unref_page+0xdf/0x170
? psi_group_change+0x113/0x390
verity_tasklet+0xd/0x70 [dm_verity]
tasklet_action_common.isra.0+0xb3/0xc0
__do_softirq+0xaf/0x1ec
? smpboot_thread_fn+0x1d/0x200
? sort_range+0x20/0x20
run_ksoftirqd+0x15/0x30
smpboot_thread_fn+0xed/0x200
kthread+0xdc/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x28/0x40
? kthread_complete_and_exit+0x20/0x20
ret_from_fork_asm+0x11/0x20
</TASK>
This commit fixes dm-verity so that it doesn't use the flags
CRYPTO_TFM_REQ_MAY_SLEEP and CRYPTO_TFM_REQ_MAY_BACKLOG from tasklets. The
crypto API would do GFP_ATOMIC allocation instead, it could return -ENOMEM
and we catch -ENOMEM in verity_tasklet and requeue the request to the
workqueue.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # v6.0+
Fixes: 5721d4e5a9 ("dm verity: Add optional "try_verify_in_tasklet" feature")
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a695062a5 upstream.
dm-bufio has a no-sleep mode. When activated (with the
DM_BUFIO_CLIENT_NO_SLEEP flag), the bufio client is read-only and we
could call dm_bufio_get from tasklets. This is used by dm-verity.
Unfortunately, commit 450e8dee51 ("dm bufio: improve concurrent IO
performance") broke this and the kernel would warn that cache_get()
was calling down_read() from no-sleeping context. The bug can be
reproduced by using "veritysetup open" with the "--use-tasklets"
flag.
This commit fixes dm-bufio, so that the tasklet mode works again, by
expanding use of the 'no_sleep_enabled' static_key to conditionally
use either a rw_semaphore or rwlock_t (which are colocated in the
buffer_tree structure using a union).
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # v6.4
Fixes: 450e8dee51 ("dm bufio: improve concurrent IO performance")
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 724ff68e96 upstream.
Initialise the try sink compose rectangle size to the sink compose
rectangle for binner and scaler sub-devices. This was missed due to the
faulty condition that lead to the compose rectangles to be initialised for
the pixel array sub-device where it is not relevant.
Fixes: ccfc97bdb5 ("[media] smiapp: Add driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d0b89398b upstream.
The hfi parser, parses the capabilities received from venus firmware and
copies them to core capabilities. Consider below api, for example,
fill_caps - In this api, caps in core structure gets updated with the
number of capabilities received in firmware data payload. If the same api
is called multiple times, there is a possibility of copying beyond the max
allocated size in core caps.
Similar possibilities in fill_raw_fmts and fill_profile_level functions.
Cc: stable@vger.kernel.org
Fixes: 1a73374a04 ("media: venus: hfi_parser: add common capability parser")
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b18e36dfd6 upstream.
Buffer requirement, for different buffer type, comes from video firmware.
While copying these requirements, there is an OOB possibility when the
payload from firmware is more than expected size. Fix the check to avoid
the OOB possibility.
Cc: stable@vger.kernel.org
Fixes: 09c2845e8f ("[media] media: venus: hfi: add Host Firmware Interface (HFI)")
Reviewed-by: Nathan Hebert <nhebert@chromium.org>
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0768a9dd80 upstream.
Supported codec bitmask is populated from the payload from venus firmware.
There is a possible case when all the bits in the codec bitmask is set. In
such case, core cap for decoder is filled and MAX_CODEC_NUM is utilized.
Now while filling the caps for encoder, it can lead to access the caps
array beyong 32 index. Hence leading to OOB write.
The fix counts the supported encoder and decoder. If the count is more than
max, then it skips accessing the caps.
Cc: stable@vger.kernel.org
Fixes: 1a73374a04 ("media: venus: hfi_parser: add common capability parser")
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8a489f820 upstream.
When transmitting, infrared drivers expect an odd number of samples; iow
without a trailing space. No problems have been observed so far, so
this is just belt and braces.
Fixes: 9b6192589b ("media: lirc: implement scancode sending")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0d4e8acb3 upstream.
With gcc and W=1 option, there's a warning like this:
fs/f2fs/compress.c: In function ‘f2fs_init_page_array_cache’:
fs/f2fs/compress.c:1984:47: error: ‘%u’ directive writing between
1 and 7 bytes into a region of size between 5 and 8
[-Werror=format-overflow=]
1984 | sprintf(slab_name, "f2fs_page_array_entry-%u:%u", MAJOR(dev),
MINOR(dev));
| ^~
String "f2fs_page_array_entry-%u:%u" can up to 35. The first "%u" can up
to 4 and the second "%u" can up to 7, so total size is "24 + 4 + 7 = 35".
slab_name's size should be 35 rather than 32.
Cc: stable@vger.kernel.org
Signed-off-by: Su Hui <suhui@nfschina.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50a472bbc7 upstream.
If we return the error, there's no way to recover the status as of now, since
fsck does not fix the xattr boundary issue.
Cc: stable@vger.kernel.org
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f78ca48a8b upstream.
Currently we set SMBHSTCNT_LAST_BYTE only after the host has started
receiving the last byte. If we get e.g. preempted before setting
SMBHSTCNT_LAST_BYTE, the host may be finished with receiving the byte
before SMBHSTCNT_LAST_BYTE is set.
Therefore change the code to set SMBHSTCNT_LAST_BYTE before writing
SMBHSTSTS_BYTE_DONE for the byte before the last byte. Now the code
is also consistent with what we do in i801_isr_byte_done().
Reported-by: Jean Delvare <jdelvare@suse.com>
Closes: https://lore.kernel.org/linux-i2c/20230828152747.09444625@endymion.delvare/
Cc: stable@vger.kernel.org
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cdc6f44e9 upstream.
In gfs2_fill_super(), when mounting a gfs2 filesystem is interrupted,
kthread_create() can return -EINTR. When that happens, we roll back
what has already been done and abort the mount.
Since commit 62dd0f98a0 ("gfs2: Flag a withdraw if init_threads()
fails), we are calling gfs2_withdraw_delayed() in gfs2_fill_super();
first via gfs2_make_fs_rw(), then directly. But gfs2_withdraw_delayed()
only marks the filesystem as withdrawing and relies on a caller further
up the stack to do the actual withdraw, which doesn't exist in the
gfs2_fill_super() case. Because the filesystem is marked as withdrawing
/ withdrawn, function gfs2_lm_unmount() doesn't release the dlm
lockspace, so when we try to mount that filesystem again, we get:
gfs2: fsid=gohan:gohan0: Trying to join cluster "lock_dlm", "gohan:gohan0"
gfs2: fsid=gohan:gohan0: dlm_new_lockspace error -17
Since commit b77b4a4815 ("gfs2: Rework freeze / thaw logic"), the
deadlock this gfs2_withdraw_delayed() call was supposed to work around
cannot occur anymore because freeze_go_callback() won't take the
sb->s_umount semaphore unconditionally anymore, so we can get rid of the
gfs2_withdraw_delayed() in gfs2_fill_super() entirely.
Reported-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Cc: stable@vger.kernel.org # v6.5+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02d5fdbf4f upstream.
Background: Turris Omnia (Armada 385); eth2 (mvneta) connected to SFP bus;
SFP module is present, but no fiber connected, so definitely no carrier.
After booting, eth2 is down, but netdev LED trigger surprisingly reports
link active. Then, after "ip link set eth2 up", the link indicator goes
away - as I would have expected it from the beginning.
It turns out, that the default carrier state after netdev creation is
"carrier ok". Some ethernet drivers explicitly call netif_carrier_off
during probing, others (like mvneta) don't - which explains the current
behaviour: only when the device is brought up, phylink_start calls
netif_carrier_off.
Fix this for all drivers using phylink, by calling netif_carrier_off in
phylink_create.
Fixes: 089381b27a ("leds: initial support for Turris Omnia LEDs")
Cc: stable@vger.kernel.org
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f55d8e60f1 upstream.
This function takes a pointer to a pointer, unlike sprintf() which is
passed a plain pointer. Fix up the documentation to make this clear.
Fixes: 7888fe53b7 ("ethtool: Add common function for filling out strings")
Cc: Alexander Duyck <alexanderduyck@fb.com>
Cc: Justin Stitt <justinstitt@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Justin Stitt <justinstitt@google.com>
Link: https://lore.kernel.org/r/20231028192511.100001-1-andrew@lunn.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e14aec2302 upstream.
Fix kernel crash in AP bus code caused by very early invocation of the
config change callback function via SCLP.
After a fresh IML of the machine the crypto cards are still offline and
will get switched online only with activation of any LPAR which has the
card in it's configuration. A crypto card coming online is reported
to the LPAR via SCLP and the AP bus offers a callback function to get
this kind of information. However, it may happen that the callback is
invoked before the AP bus init function is complete. As the callback
triggers a synchronous AP bus scan, the scan may already run but some
internal states are not initialized by the AP bus init function resulting
in a crash like this:
[ 11.635859] Unable to handle kernel pointer dereference in virtual kernel address space
[ 11.635861] Failing address: 0000000000000000 TEID: 0000000000000887
[ 11.635862] Fault in home space mode while using kernel ASCE.
[ 11.635864] AS:00000000894c4007 R3:00000001fece8007 S:00000001fece7800 P:000000000000013d
[ 11.635879] Oops: 0004 ilc:1 [#1] SMP
[ 11.635882] Modules linked in:
[ 11.635884] CPU: 5 PID: 42 Comm: kworker/5:0 Not tainted 6.6.0-rc3-00003-g4dbf7cdc6b42 #12
[ 11.635886] Hardware name: IBM 3931 A01 751 (LPAR)
[ 11.635887] Workqueue: events_long ap_scan_bus
[ 11.635891] Krnl PSW : 0704c00180000000 0000000000000000 (0x0)
[ 11.635895] R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:0 PM:0 RI:0 EA:3
[ 11.635897] Krnl GPRS: 0000000001000a00 0000000000000000 0000000000000006 0000000089591940
[ 11.635899] 0000000080000000 0000000000000a00 0000000000000000 0000000000000000
[ 11.635901] 0000000081870c00 0000000089591000 000000008834e4e2 0000000002625a00
[ 11.635903] 0000000081734200 0000038000913c18 000000008834c6d6 0000038000913ac8
[ 11.635906] Krnl Code:>0000000000000000: 0000 illegal
[ 11.635906] 0000000000000002: 0000 illegal
[ 11.635906] 0000000000000004: 0000 illegal
[ 11.635906] 0000000000000006: 0000 illegal
[ 11.635906] 0000000000000008: 0000 illegal
[ 11.635906] 000000000000000a: 0000 illegal
[ 11.635906] 000000000000000c: 0000 illegal
[ 11.635906] 000000000000000e: 0000 illegal
[ 11.635915] Call Trace:
[ 11.635916] [<0000000000000000>] 0x0
[ 11.635918] [<000000008834e4e2>] ap_queue_init_state+0x82/0xb8
[ 11.635921] [<000000008834ba1c>] ap_scan_domains+0x6fc/0x740
[ 11.635923] [<000000008834c092>] ap_scan_adapter+0x632/0x8b0
[ 11.635925] [<000000008834c3e4>] ap_scan_bus+0xd4/0x288
[ 11.635927] [<00000000879a33ba>] process_one_work+0x19a/0x410
[ 11.635930] Discipline DIAG cannot be used without z/VM
[ 11.635930] [<00000000879a3a2c>] worker_thread+0x3fc/0x560
[ 11.635933] [<00000000879aea60>] kthread+0x120/0x128
[ 11.635936] [<000000008792afa4>] __ret_from_fork+0x3c/0x58
[ 11.635938] [<00000000885ebe62>] ret_from_fork+0xa/0x30
[ 11.635942] Last Breaking-Event-Address:
[ 11.635942] [<000000008834c6d4>] ap_wait+0xcc/0x148
This patch improves the ap_bus_force_rescan() function which is
invoked by the config change callback by checking if a first
initial AP bus scan has been done. If not, the force rescan request
is simple ignored. Anyhow it does not make sense to trigger AP bus
re-scans even before the very first bus scan is complete.
Cc: stable@vger.kernel.org
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8183fa10c upstream.
During SMBus block data read process, we have seen high interrupt rate
because of TX_EMPTY irq status while waiting for block length byte (the
first data byte after the address phase). The interrupt handler does not
do anything because the internal state is kept as STATUS_WRITE_IN_PROGRESS.
Hence, we should disable TX_EMPTY IRQ until I2C DesignWare receives
first data byte from I2C device, then re-enable it to resume SMBus
transaction.
It takes 0.789 ms for host to receive data length from slave.
Without the patch, i2c_dw_isr() is called 99 times by TX_EMPTY interrupt.
And it is none after applying the patch.
Cc: stable@vger.kernel.org
Co-developed-by: Chuong Tran <chuong@os.amperecomputing.com>
Signed-off-by: Chuong Tran <chuong@os.amperecomputing.com>
Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d6aa89bba upstream.
Commit abd3ac7902 ("watchdog: sbsa: Support architecture version 1")
introduced new timer math for watchdog revision 1 with the 48 bit offset
register.
The gwdt->clk and timeout are u32, but the argument being calculated is
u64. Without a cast, the compiler performs u32 operations, truncating
intermediate steps, resulting in incorrect values.
A watchdog revision 1 implementation with a gwdt->clk of 1GHz and a
timeout of 600s writes 3647256576 to the one shot watchdog instead of
300000000000, resulting in the watchdog firing in 3.6s instead of 600s.
Force u64 math by casting the first argument (gwdt->clk) as a u64. Make
the order of operations explicit with parenthesis.
Fixes: abd3ac7902 ("watchdog: sbsa: Support architecture version 1")
Reported-by: Vanshidhar Konda <vanshikonda@os.amperecomputing.com>
Signed-off-by: Darren Hart <darren@os.amperecomputing.com>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: <stable@vger.kernel.org> # 5.14.x
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/7d1713c5ffab19b0f3de796d82df19e8b1f340de.1695286124.git.darren@os.amperecomputing.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b36995b860 upstream.
-EOPNOTSUPP is the return value that implements a "no-op" hook, not 0.
Without this fix having only the BPF LSM enabled (with no programs
attached) can cause uninitialized variable reads in
nfsd4_encode_fattr(), because the BPF hook returns 0 without touching
the 'ctxlen' variable and the corresponding 'contextlen' variable in
nfsd4_encode_fattr() remains uninitialized, yet being treated as valid
based on the 0 return value.
Cc: stable@vger.kernel.org
Fixes: 98e828a065 ("security: Refactor declaration of LSM hooks")
Reported-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 866d648059 upstream.
1 is the return value that implements a "no-op" hook, not 0.
Cc: stable@vger.kernel.org
Fixes: 98e828a065 ("security: Refactor declaration of LSM hooks")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b211c7671 upstream.
This reverts commit 0b01392c18.
Conversion of PXA to generic I2C recovery, makes the I2C bus completely
lock up if recovery pinctrl is present in the DT and I2C recovery is
enabled.
So, until the generic I2C recovery can also work with PXA lets revert
to have working I2C and I2C recovery again.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: stable@vger.kernel.org # 5.11+
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e2e7efbbb upstream.
This reverts commit 3780bb2931.
The cited commit introduced unwanted behavior.
The intent for the commit was to be able to detect carrier loss/gain
for just the NIC connected to the BMC. The unwanted effect is a
carrier loss for auxiliary paths also causes the BMC to lose
carrier. The BMC never regains carrier despite the secondary NIC
regaining a link.
This change, when merged, needs to be backported to stable kernels.
5.4-stable, 5.10-stable, 5.15-stable, 6.1-stable, 6.5-stable
Fixes: 3780bb2931 ("ncsi: Propagate carrier gain/loss events to the NCSI controller")
CC: stable@vger.kernel.org
Signed-off-by: Johnathan Mantey <johnathanx.mantey@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d639b6097 upstream.
These HP laptops use Realtek HDA codec combined with 2 or 4 CS35L41
Amplifiers using SPI with Internal Boost.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231115162116.494968-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b944aa9d86 upstream.
HP 255 G10 has a mute LED that can be made to work using quirk
ALC236_FIXUP_HP_MUTE_LED_COEFBIT2.
Enable already existing quirk - at correct line to keep order
Signed-off-by: Matus Malych <matus@malych.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231114133524.11340-1-matus@malych.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b21a669ca upstream.
Add ALC295 to pin fall back table.
Remove 5 pin quirks for Dell ALC295.
ALC295 was only support MIC2 for external MIC function.
ALC295 assigned model "ALC269_FIXUP_DELL1_MIC_NO_PRESENCE" for pin
fall back table.
It was assigned wrong model. So, let's remove it.
Fixes: fbc571290d ("ALSA: hda/realtek - Fixed Headphone Mic can't record on Dell platform")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/7c1998e873834df98d59bd7e0d08c72e@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7a6065195 upstream.
As reported recently, ALSA core info helper may cause a deadlock at
the forced device disconnection during the procfs operation.
The proc_remove() (that is called from the snd_card_disconnect()
helper) has a synchronization of the pending procfs accesses via
wait_for_completion(). Meanwhile, ALSA procfs helper takes the global
mutex_lock(&info_mutex) at both the proc_open callback and
snd_card_info_disconnect() helper. Since the proc_open can't finish
due to the mutex lock, wait_for_completion() never returns, either,
hence it deadlocks.
TASK#1 TASK#2
proc_reg_open()
takes use_pde()
snd_info_text_entry_open()
snd_card_disconnect()
snd_info_card_disconnect()
takes mutex_lock(&info_mutex)
proc_remove()
wait_for_completion(unused_pde)
... waiting task#1 closes
mutex_lock(&info_mutex)
=> DEADLOCK
This patch is a workaround for avoiding the deadlock scenario above.
The basic strategy is to move proc_remove() call outside the mutex
lock. proc_remove() can work gracefully without extra locking, and it
can delete the tree recursively alone. So, we call proc_remove() at
snd_info_card_disconnection() at first, then delete the rest resources
recursively within the info_mutex lock.
After the change, the function snd_info_disconnect() doesn't do
disconnection by itself any longer, but it merely clears the procfs
pointer. So rename the function to snd_info_clear_entries() for
avoiding confusion.
The similar change is applied to snd_info_free_entry(), too. Since
the proc_remove() is called only conditionally with the non-NULL
entry->p, it's skipped after the snd_info_clear_entries() call.
Reported-by: Shinhyung Kang <s47.kang@samsung.com>
Closes: https://lore.kernel.org/r/664457955.21699345385931.JavaMail.epsvc@epcpadp4
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231109141954.4283-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
