stm32_defconfig is used for several STM32 MCU: STM32F429, STM32F469,
STM32F746 and now STM32H743. Each of MCU listed have different interrupts
number mapped on NVIC. STM32F429: 81, STM32F469: 92, STM32F746: 97 and
STM32H743: 149. I could set CPU_V7M_NUM_IRQ to 149 but in order to avoid
forgetting to update this value for next STM32 MCU I prefer to set it to
max value: 240.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The imx6sl-evk board has a LAN8720A ethernet phy supported by SMSC_PHY.
Add this driver to the default imx config since the device is present on
one of the evaluation boards.
This used to work mostly fine with the generic phy driver until
commit 0878fff1f4 ("net: phy: Do not perform software reset for
Generic PHY"). The fact that soft reset is no longer performed
apparently causes RX to sometimes failes which can cause netboot to
timeout on DHCP. This is eventually retried and it works after link
up/down but can takes 90 seconds to reach the login prompt.
This was generated with "make savedefconfig" and it includes a few
additional minor cleanups.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts davinci_all_defconfig to use libata PATA
drivers.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[b.zolnierkie: split from bigger patch + added patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
An adsp-pil node is present in at least the MSM8974 SoC. Simply enable
all Qualcomm remoteproc drivers to avoid more work in the future.
The SMP2P driver is required for adsp-pil to initialize correctly.
Enable the SMSM driver at Bjorn Andersson's request: "We also need
CONFIG_QCOM_SMSM=y here, its currently used to signal state of the ring
buffers for WiFi."
CONFIG_QCOM_WCNSS_CTRL is required to load firmware/configuration data
into the WCNSS core, which handles WiFi and Bluetooth.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This is now supported on the dm8168-evm board, so enable it in
the defconfig for omap2+.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to enable this controller so that we can switch the SD card's
pinmux over to it by default, which will improve storage performance.
Read access (dd with 64k blocks on rpi2):
CONFIG_MMC_SDHCI_IPROC: 11-12 MB/s
CONFIG_MMC_BCM2835: 19-20 MB/s
Differences on write access are pretty much in the noise.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Currently bcm2835_defconfig has CMA disabled which makes the
HDMI output on a Raspberry Pi 1 stop working during boot:
fb: switching to vc4drmfb from simple
Console: switching to colour dummy device 80x30
[drm] Initialized vc4 0.0.0 20140616 for soc:gpu on minor 0
[drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[drm] Driver supports precise vblank timestamp query.
vc4-drm soc:gpu: failed to allocate buffer with size 9216000
vc4-drm soc:gpu: Failed to set initial hw configuration.
So enable CMA and DMA_CMA in bcm2835_defconfig.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 4400d9ac05 ("ARM: bcm2835: Enable the VC4 graphics driver in the defconfig")
Reviewed-by: Eric Anholt <eric@anholt.net>
This patch enables Altera TSE support in socfpga_defconfig
Signed-off-by: Jia Jie Ho <ho.jia.jie@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Select CONFIG_HID_MULTITOUCH so that we can have multi touchscreen
funtionality via USB by default on Engicam i.CoreM6 Quad with
OpenFrame Cap 10.1 display boards.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Select CONFIG_TOUCHSCREEN_MAX11801 so that we can have touchscreen
funtionality by default on Engicam i.CoreM6 Quad boards.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Current CMA size of 64 Mbytes is right on the edge of being small when
several drivers need to allocate large CMA buffers.
For example, if the s5p-mfc driver needs to pre-allocate CMA memory to
decode a H.264 1080p video, then there won't be enough CMA memory left
for other drivers, such as the exynos-drm driver that may need to
allocate GEM buffers for the display manager.
Increasing CMA size to 96 Mbytes in exynos_defconfig addresses use-cases
such as these.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
DYNAMIC_DEBUG is quite useful for debugging kernels and should not cause
noticeable performance regressions. It makes the kernel bigger (around 4%)
but this difference should not impact typical developer and reference
usage of this defconfig.
Sizes:
zImage-old: 4641496 bytes
zImage-new: 4811384 bytes
text data bss dec hex filename
7031229 2570916 327016 9929161 9781c9 vmlinux-old
7205921 2800052 327016 10332989 9dab3d vmlinux-new
Additionally, remove the EXT3_FS symbol because it is entirely replaced
by EXT4_FS.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
This enables the TI ADS7950 IIO driver. This is used on LEGO MINDSTORMS
EV3. The other IIO configs removed in this patch are selected by
CONFIG_TI_ADS7950, so they are not actually being desabled.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
AM335x, AM437x, DRA7xx, and AM57xx platforms all now depend on
ti-cpufreq driver to enable proper OPPs for use with cpufreq, so
enable the same.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need IRQs from the tca6416 expander for vpif capture to work on the
da850-evm board.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Enable the VPIF display module and the video encoder present on the
da850-evm UI board.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The AXP20X regulator support is currently built as a module, which means
it's not available until the root fs has been mounted, but the boot loader
might not have enabled the required regulators, so build their drivers
into the kernel.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the AC100 RTC driver so boards with it can keep track of time.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The sunxi RSB bus is used for peripherals like voltage regulators and
real-time clocks which should be available early in the boot process.
As a module, the driver will not be available until the root fs has been
mounted, so build the driver into the kernel.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the AC100 RTC driver so boards with it can keep track of time.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The moxart defconfig wasn't even building a kernel for Moxart,
it was building a kernel for V4T on the nothing platform. Switch
to MULTI_V4 and keep the right drivers, update a few selections.
Now it (presumably) builds a minimalist Moxart kernel again.
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Defconfig additions, removals, etc. Almost all of them just turn on
drivers that we want on some platform, usually after the driver
has been merged into mainline.
There is now a new defconfig file for tango4.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=noKQ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"Defconfig additions, removals, etc. Almost all of them just turn on
drivers that we want on some platform, usually after the driver has
been merged into mainline.
There is now a new defconfig file for tango4"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: multi_v7_defconfig: enable pstore configs
ARM: multi_v7_defconfig: enable some newly added crypto modules
ARM: davinci_all_defconfig: enable SATA modules
arm64: defconfig: enable CONFIG_MTD_NAND and CONFIG_MTD_NAND_DENALI_DT
arm64: defconfig: enable CONFIG_MTD_BLOCK
ARM: Import tango4_defconfig
ARM: omap2plus_defconfig: Enable support for RTC M41T80
ARM: omap2plus_defconfig: Enable support for micrell phys
ARM: vf610m4: defconfig: enable EXT4 filesystem
ARM: omap2plus_defconfig: Fix probe errors on UARTs 5 and 6
arm64: defconfig: Enable NUMA and NUMA_BALANCING
arm64: defconfig: enable SMMUv3 config
ARM: davinci_all_defconfig: enable iio
ARM: Keystone: Enable ARCH_HAS_RESET_CONTROLLER
ARM: configs: stm32: Add RTC support in STM32 defconfig
ARM: defconfig: qcom: add APQ8060 DragonBoard devices
ARM: qcom_defconfig: enable thermal sensors
ARM: qcom_defconfig: add ahci configs
ARM: qcom_defconfig: add pcie and atl1c ethernet configs
ARM: qcom_defconfig: add usb related configs
...
Pull networking updates from David Miller:
"Highlights:
1) Support TX_RING in AF_PACKET TPACKET_V3 mode, from Sowmini
Varadhan.
2) Simplify classifier state on sk_buff in order to shrink it a bit.
From Willem de Bruijn.
3) Introduce SIPHASH and it's usage for secure sequence numbers and
syncookies. From Jason A. Donenfeld.
4) Reduce CPU usage for ICMP replies we are going to limit or
suppress, from Jesper Dangaard Brouer.
5) Introduce Shared Memory Communications socket layer, from Ursula
Braun.
6) Add RACK loss detection and allow it to actually trigger fast
recovery instead of just assisting after other algorithms have
triggered it. From Yuchung Cheng.
7) Add xmit_more and BQL support to mvneta driver, from Simon Guinot.
8) skb_cow_data avoidance in esp4 and esp6, from Steffen Klassert.
9) Export MPLS packet stats via netlink, from Robert Shearman.
10) Significantly improve inet port bind conflict handling, especially
when an application is restarted and changes it's setting of
reuseport. From Josef Bacik.
11) Implement TX batching in vhost_net, from Jason Wang.
12) Extend the dummy device so that VF (virtual function) features,
such as configuration, can be more easily tested. From Phil
Sutter.
13) Avoid two atomic ops per page on x86 in bnx2x driver, from Eric
Dumazet.
14) Add new bpf MAP, implementing a longest prefix match trie. From
Daniel Mack.
15) Packet sample offloading support in mlxsw driver, from Yotam Gigi.
16) Add new aquantia driver, from David VomLehn.
17) Add bpf tracepoints, from Daniel Borkmann.
18) Add support for port mirroring to b53 and bcm_sf2 drivers, from
Florian Fainelli.
19) Remove custom busy polling in many drivers, it is done in the core
networking since 4.5 times. From Eric Dumazet.
20) Support XDP adjust_head in virtio_net, from John Fastabend.
21) Fix several major holes in neighbour entry confirmation, from
Julian Anastasov.
22) Add XDP support to bnxt_en driver, from Michael Chan.
23) VXLAN offloads for enic driver, from Govindarajulu Varadarajan.
24) Add IPVTAP driver (IP-VLAN based tap driver) from Sainath Grandhi.
25) Support GRO in IPSEC protocols, from Steffen Klassert"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1764 commits)
Revert "ath10k: Search SMBIOS for OEM board file extension"
net: socket: fix recvmmsg not returning error from sock_error
bnxt_en: use eth_hw_addr_random()
bpf: fix unlocking of jited image when module ronx not set
arch: add ARCH_HAS_SET_MEMORY config
net: napi_watchdog() can use napi_schedule_irqoff()
tcp: Revert "tcp: tcp_probe: use spin_lock_bh()"
net/hsr: use eth_hw_addr_random()
net: mvpp2: enable building on 64-bit platforms
net: mvpp2: switch to build_skb() in the RX path
net: mvpp2: simplify MVPP2_PRS_RI_* definitions
net: mvpp2: fix indentation of MVPP2_EXT_GLOBAL_CTRL_DEFAULT
net: mvpp2: remove unused register definitions
net: mvpp2: simplify mvpp2_bm_bufs_add()
net: mvpp2: drop useless fields in mvpp2_bm_pool and related code
net: mvpp2: remove unused 'tx_skb' field of 'struct mvpp2_tx_queue'
net: mvpp2: release reference to txq_cpu[] entry after unmapping
net: mvpp2: handle too large value in mvpp2_rx_time_coal_set()
net: mvpp2: handle too large value handling in mvpp2_rx_pkts_coal_set()
net: mvpp2: remove useless arguments in mvpp2_rx_{pkts, time}_coal_set
...
CONFIG_SET_MODULE_RONX to the more sensible CONFIG_STRICT_KERNEL_RWX and
CONFIG_STRICT_MODULE_RWX.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=7KhR
-----END PGP SIGNATURE-----
Merge tag 'rodata-v4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull rodata updates from Kees Cook:
"This renames the (now inaccurate) DEBUG_RODATA and related
SET_MODULE_RONX configs to the more sensible STRICT_KERNEL_RWX and
STRICT_MODULE_RWX"
* tag 'rodata-v4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
arch: Rename CONFIG_DEBUG_RODATA and CONFIG_DEBUG_MODULE_RONX
arch: Move CONFIG_DEBUG_RODATA and CONFIG_SET_MODULE_RONX to be common
- Operating Performance Points (OPP) framework fixes, cleanups and
switch over from RCU-based synchronization to reference counting
using krefs (Viresh Kumar, Wei Yongjun, Dave Gerlach).
- cpufreq core cleanups and documentation updates (Viresh Kumar,
Rafael Wysocki).
- New cpufreq driver for Broadcom BMIPS SoCs (Markus Mayer).
- New cpufreq-dt sub-driver for TI SoCs requiring special handling,
like in the AM335x, AM437x, DRA7x, and AM57x families, along with
new DT bindings for it (Dave Gerlach, Paul Gortmaker).
- ARM64 SoCs support for the qoriq cpufreq driver (Tang Yuantian).
- intel_pstate driver updates including a new sysfs knob to control
the driver's operation mode and fixes related to the no_turbo
sysfs knob and the hardware-managed P-states feature support
(Rafael Wysocki, Srinivas Pandruvada).
- New interface to export ultra-turbo frequencies for the powernv
cpufreq driver (Shilpasri Bhat).
- Assorted fixes for cpufreq drivers (Arnd Bergmann, Dan Carpenter,
Wei Yongjun).
- devfreq core fixes, mostly related to the sysfs interface exported
by it (Chanwoo Choi, Chris Diamand).
- Updates of the exynos-bus and exynos-ppmu devfreq drivers (Chanwoo
Choi).
- Device PM QoS extension to support CPUs and support for per-CPU
wakeup (device resume) latency constraints in the cpuidle menu
governor (Alex Shi).
- Wakeup IRQs framework fixes (Grygorii Strashko).
- Generic power domains framework update including a fix to make
it handle asynchronous invocations of *noirq suspend/resume
callbacks correctly (Ulf Hansson, Geert Uytterhoeven).
- Assorted fixes and cleanups in the core suspend/hibernate code,
PM QoS framework and x86 ACPI idle support code (Corentin Labbe,
Geert Uytterhoeven, Geliang Tang, John Keeping, Nick Desaulniers).
- Update of the analyze_suspend.py script is updated to version 4.5
offering multiple improvements (Todd Brandt).
- New tool for intel_pstate diagnostics using the pstate_sample
tracepoint (Doug Smythies).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=57xJ
-----END PGP SIGNATURE-----
Merge tag 'pm-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The majority of changes go into the Operating Performance Points (OPP)
framework and cpufreq this time, followed by devfreq and some
scattered updates all over.
The OPP changes are mostly related to switching over from RCU-based
synchronization, that turned out to be overly complicated and
problematic, to reference counting using krefs.
In the cpufreq land there are core cleanups, documentation updates, a
new driver for Broadcom BMIPS SoCs, a new cpufreq-dt sub-driver for TI
SoCs that require special handling, ARM64 SoCs support for the qoriq
driver, intel_pstate updates, powernv driver update and assorted
fixes.
The devfreq changes are mostly fixes related to the sysfs interface
and some Exynos drivers updates.
Apart from that, the cpuidle menu governor will support per-CPU PM QoS
constraints for the wakeup latency now, some bugs in the wakeup IRQs
framework are fixed, the generic power domains framework should handle
asynchronous invocations of *noirq suspend/resume callbacks from now
on, the analyze_suspend.py script is updated and there is a new tool
for intel_pstate diagnostics.
Specifics:
- Operating Performance Points (OPP) framework fixes, cleanups and
switch over from RCU-based synchronization to reference counting
using krefs (Viresh Kumar, Wei Yongjun, Dave Gerlach)
- cpufreq core cleanups and documentation updates (Viresh Kumar,
Rafael Wysocki)
- New cpufreq driver for Broadcom BMIPS SoCs (Markus Mayer)
- New cpufreq-dt sub-driver for TI SoCs requiring special handling,
like in the AM335x, AM437x, DRA7x, and AM57x families, along with
new DT bindings for it (Dave Gerlach, Paul Gortmaker)
- ARM64 SoCs support for the qoriq cpufreq driver (Tang Yuantian)
- intel_pstate driver updates including a new sysfs knob to control
the driver's operation mode and fixes related to the no_turbo sysfs
knob and the hardware-managed P-states feature support (Rafael
Wysocki, Srinivas Pandruvada)
- New interface to export ultra-turbo frequencies for the powernv
cpufreq driver (Shilpasri Bhat)
- Assorted fixes for cpufreq drivers (Arnd Bergmann, Dan Carpenter,
Wei Yongjun)
- devfreq core fixes, mostly related to the sysfs interface exported
by it (Chanwoo Choi, Chris Diamand)
- Updates of the exynos-bus and exynos-ppmu devfreq drivers (Chanwoo
Choi)
- Device PM QoS extension to support CPUs and support for per-CPU
wakeup (device resume) latency constraints in the cpuidle menu
governor (Alex Shi)
- Wakeup IRQs framework fixes (Grygorii Strashko)
- Generic power domains framework update including a fix to make it
handle asynchronous invocations of *noirq suspend/resume callbacks
correctly (Ulf Hansson, Geert Uytterhoeven)
- Assorted fixes and cleanups in the core suspend/hibernate code, PM
QoS framework and x86 ACPI idle support code (Corentin Labbe, Geert
Uytterhoeven, Geliang Tang, John Keeping, Nick Desaulniers)
- Update of the analyze_suspend.py script is updated to version 4.5
offering multiple improvements (Todd Brandt)
- New tool for intel_pstate diagnostics using the pstate_sample
tracepoint (Doug Smythies)"
* tag 'pm-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (85 commits)
MAINTAINERS: cpufreq: add bmips-cpufreq.c
PM / QoS: Fix memory leak on resume_latency.notifiers
PM / Documentation: Spelling s/wrtie/write/
PM / sleep: Fix test_suspend after sleep state rework
cpufreq: CPPC: add ACPI_PROCESSOR dependency
cpufreq: make ti-cpufreq explicitly non-modular
cpufreq: Do not clear real_cpus mask on policy init
tools/power/x86: Debug utility for intel_pstate driver
AnalyzeSuspend: fix drag and zoom bug in javascript
PM / wakeirq: report a wakeup_event on dedicated wekup irq
PM / wakeirq: Fix spurious wake-up events for dedicated wakeirqs
PM / wakeirq: Enable dedicated wakeirq for suspend
cpufreq: dt: Don't use generic platdev driver for ti-cpufreq platforms
cpufreq: ti: Add cpufreq driver to determine available OPPs at runtime
Documentation: dt: add bindings for ti-cpufreq
PM / OPP: Expose _of_get_opp_desc_node as dev_pm_opp API
cpufreq: qoriq: Don't look at clock implementation details
cpufreq: qoriq: add ARM64 SoCs support
PM / Domains: Provide dummy governors if CONFIG_PM_GENERIC_DOMAINS=n
cpufreq: brcmstb-avs-cpufreq: remove unnecessary platform_set_drvdata()
...
This patch enables the Qualcomm RPM based Clock Controller present on
A-family boards.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It's useful to get testing on these features on various boards (e.g., on
KernelCI), and (when they're working) the ramoops feature is extremely
helpful for debugging live systems.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the new accelerated CRC32(C), CRC-T10DIF and ChaCha20 drivers
as modules for multi_v7_defconfig builds.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Gwrq
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.11/defconfig-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/defconfig
Pull "Enable SATA support found on DA850 SoC" from Sekhar Nori:
* tag 'davinci-for-v4.11/defconfig-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci_all_defconfig: enable SATA modules
Both of these options are poorly named. The features they provide are
necessary for system security and should not be considered debug only.
Change the names to CONFIG_STRICT_KERNEL_RWX and
CONFIG_STRICT_MODULE_RWX to better describe what these options do.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Jessica Yu <jeyu@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
A single patch to enable the thermal DT support in sunxi_defconfig
-----BEGIN PGP SIGNATURE-----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=tqpm
-----END PGP SIGNATURE-----
Merge tag 'sunxi-defconfig-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/defconfig
Pull "Allwinner defconfig changes for 4.11" from Maxime Ripard:
A single patch to enable the thermal DT support in sunxi_defconfig
* tag 'sunxi-defconfig-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: Add CONFIG_THERMAL_OF
The symbols can no longer be used as loadable modules, leading to a harmless Kconfig
warning:
arch/arm/configs/imote2_defconfig:60:warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE
arch/arm/configs/imote2_defconfig:59:warning: symbol value 'm' invalid for NF_CT_PROTO_SCTP
arch/arm/configs/ezx_defconfig:68:warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE
arch/arm/configs/ezx_defconfig:67:warning: symbol value 'm' invalid for NF_CT_PROTO_SCTP
Let's make them built-in.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This doesn't have any benefit apart from saving a small amount of memory
when it is disabled. The ifdef hackery in the code makes it dirty
unnecessarily.
Clean it up by removing the Kconfig option completely. Few defconfigs
are also updated and CONFIG_CPU_FREQ_STAT_DETAILS is replaced with
CONFIG_CPU_FREQ_STAT now in them, as users wanted stats to be enabled.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add the da850-ahci driver to davinci defconfig.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
- Select wireless extensions option for imx_v6_v7_defconfig, so that
wireless works out of box with userspace tools such as 'iwconfig'.
- Enable EXT4 filesystem support for vf610m4_defconfig.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYjWf2AAoJEFBXWFqHsHzOSicH/Rg+X7Qat+pMxINB7+enJqlw
mIM5WTUwhO4txugFD84ybcBitC/+t/kS5ffEM7ckkDDn6p6bN0K9vcU137V/CkE2
cMHgnuawXs3qCu4D+h4X3MsdF/AWTOD20dv1W5QMhC9/kANP2emQ6ohB5Wee0Gmx
5Mi4UaD0QNYrFsukayWhQ45i0RbsNRdiyzAntIpY1Xz8JJGL/ufTk233wtfxihsV
8MQw/Ar1Q3Hz8+eIKj+9dqDKV5AUrXQ3GvrvTfwlXlLM+NNSN5UWfJsbzob9754P
h02zRhjtQfjFKTUVAJKQPTNPci8b+8InnKyLgqSNSAnb/2PXtJB0AlFXJfaZ/LM=
=VjCo
-----END PGP SIGNATURE-----
Merge tag 'imx-defconfig-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/defconfig
i.MX defconfig updates for 4.11:
- Select wireless extensions option for imx_v6_v7_defconfig, so that
wireless works out of box with userspace tools such as 'iwconfig'.
- Enable EXT4 filesystem support for vf610m4_defconfig.
* tag 'imx-defconfig-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: vf610m4: defconfig: enable EXT4 filesystem
ARM: imx_v6_v7_defconfig: Select wireless extensions option
Signed-off-by: Olof Johansson <olof@lixom.net>
- Switch to use LIS3LV02DL IIO driver instead of the
LIS3LC02D misc driver
- Set CONFIG_SERIAL_8250_RUNTIME_UARTS=6 to avoid runtime
warnings on omap5 and dra7
- Enable ksz9021 phy and m41t80 rtc as they are used at
least on phyCORE-AM335x
-----BEGIN PGP SIGNATURE-----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=Vv0t
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.11/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/defconfig
Few omap2plus_defconfig changes for v4.11 merge window:
- Switch to use LIS3LV02DL IIO driver instead of the
LIS3LC02D misc driver
- Set CONFIG_SERIAL_8250_RUNTIME_UARTS=6 to avoid runtime
warnings on omap5 and dra7
- Enable ksz9021 phy and m41t80 rtc as they are used at
least on phyCORE-AM335x
* tag 'omap-for-v4.11/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2plus_defconfig: Enable support for RTC M41T80
ARM: omap2plus_defconfig: Enable support for micrell phys
ARM: omap2plus_defconfig: Fix probe errors on UARTs 5 and 6
ARM: defconfig: omap2plus: switch LIS3LV02DL driver
Signed-off-by: Olof Johansson <olof@lixom.net>
Import a minimal defconfig for tango4 boards.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The phyCORE-AM335x SoM has a RV4162 RTC populated which is supported
by the M41T80 driver. Enabled it so make the RTC support on the SoM
available.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phyCORE-AM335x SoM with PCM-953 carrierboard has a
KSZ9021 phy mounted. To add support for this we need to enable
the micrell phy driver in the config.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable EXT4_FS to have rootfs in EXT[2-4].
Other changes are result of savedefconfig keeping minimal config (even
without enabling EXT4_FS, these would be present).
Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This enables the iio subsystem. This will be used by LEGO MINDSTORMS EV3,
which has an ADS7957 chip.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Just the one commit that updates our defconfigs with network (ftgmac100
and ncsi), bt ipmi, gpio and ncsi.
ARM: configs: Update Aspeed with new drivers
-----BEGIN PGP SIGNATURE-----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=307A
-----END PGP SIGNATURE-----
Merge tag 'aspeed-4.11-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/defconfig
Aspeed defconfig updates for 4.11
Just the one commit that updates our defconfigs with network (ftgmac100
and ncsi), bt ipmi, gpio and ncsi.
* tag 'aspeed-4.11-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: configs: Update Aspeed with new drivers
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add driver support for the Axentia TSE-850
-----BEGIN PGP SIGNATURE-----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=fZjs
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.11-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/defconfig
defconfig for 4.11:
- Add driver support for the Axentia TSE-850
* tag 'at91-ab-4.11-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: sama5_defconfig: add support for the Axentia TSE-850 board
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Cleanup from old MACHs in s5pv210.
2. Enable IP_MULTICAST for libnss-mdns.
-----BEGIN PGP SIGNATURE-----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=3+O7
-----END PGP SIGNATURE-----
Merge tag 'samsung-defconfig-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/defconfig
Samsung defconfig update for v4.11:
1. Cleanup from old MACHs in s5pv210.
2. Enable IP_MULTICAST for libnss-mdns.
* tag 'samsung-defconfig-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: exynos_defconfig: Enable IP multicast
ARM: s5pv210_defconfig: Remove old MACHs
Signed-off-by: Olof Johansson <olof@lixom.net>
- enables Marvell PHY support
- enable MTD(I2C EEPROM), and NAND support
- enable SPI, RTC and LED support
- enables OF CONFIGFS to support DTS overlays
- enables more FS options
- enables A10 hwmon support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYdlZIAAoJEBmUBAuBoyj0J4MP/1L6tUv43jN9vzFISGlXCmQ/
O23QsY6ZNbpvFxXsS4DBJ3eX8Mke9Efghcl0ngZtjz6W0erqTQF0ViSOuVMfm8v8
78mziOkAohZ6hOJTTLIkRE+P4+JWZonIGkimViL/ZwtQJVKCVdOF5Jjk0Tis+kCE
/7oSmRXbb9FMSIMBLzQpNqiWaGqubiVom20pAt14UEgUfy84LIkZiMqA8QWT4329
ZH56QdQMytdbpth1aAP1W1Q38IeC/Zgm0Y5H6+IKELOSpbXq1OU7tcGOK26Gqlkh
CTvpc1iUIBs3BJUWIAbLfruEVPL5vSVeLPd4QZeuL5iVV1kRndDVs6G0nQnnnVv6
8r/4nNJ/lpxVrS4nJSO6kI+xrp5tPxmWIyzocEomVgfv9mgy1OvzT3p1o6fExrl0
qTNdz7AUTI9rYJKEta+9Eyy0oMCvJ0XZhqaDiXapiSBie4C2PYiN8aVApPT3KcDT
lqGqiyVpERYUoxPfjULxJVYb/dcGc1K8zrPaAyv6lNybLRFbg+S7uPl7PEs8z/1w
u2xxK6/UJbWXnXIMxiBjEVeRLvyjKgWtuX+saqcofLzWnNI4vATnJzXfJ7UkAEJA
jYjh0sbdtdGeCmgz01J4zlnKjdyoHK2CPCWAiAFpNP8QAXk3QB7Hg5KTRpgMypJ7
73P3hXRYeAXhBR3MFm8+
=LMBa
-----END PGP SIGNATURE-----
Merge tag 'socfpga_defconfig_updates_for_v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/defconfig
SoCFPGA defconfig updates for v4.11
- enables Marvell PHY support
- enable MTD(I2C EEPROM), and NAND support
- enable SPI, RTC and LED support
- enables OF CONFIGFS to support DTS overlays
- enables more FS options
- enables A10 hwmon support
* tag 'socfpga_defconfig_updates_for_v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga_defconfig: update defconfig for SoCFPGA
Signed-off-by: Olof Johansson <olof@lixom.net>
SoCs, please pull the following changes:
- Valenting fixes two incorrect Kconfig symbols for BCM47xx: NVRAM and watchdog drivers
-----BEGIN PGP SIGNATURE-----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=LqGx
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.10/defconfig-fixes' of http://github.com/Broadcom/stblinux into fixes
This pull request contains fixes to multi_v7_defconfig for Broadcom ARM-based
SoCs, please pull the following changes:
- Valenting fixes two incorrect Kconfig symbols for BCM47xx: NVRAM and watchdog drivers
* tag 'arm-soc/for-4.10/defconfig-fixes' of http://github.com/Broadcom/stblinux:
ARM: multi_v7_defconfig: set bcm47xx watchdog
ARM: multi_v7_defconfig: fix config typo
Signed-off-by: Olof Johansson <olof@lixom.net>
This driver is no longer necessary since it was merged into stmmac.
Acked-by: Lars Persson <larper@axis.com>
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This default-enables the devices found on the APQ8060 DragonBoard
in the qcom_defconfig:
- EBI2 bus
- SMSC911x ethernet
- LEDs class and PM8058 LEDs driver, trigger and heartbeat
trigger (so we get heartbeat on the board by default)
- IIO framework, including the HRTimer trigger, KXSD9
accelerometer, MPU3050 gyroscope, AK8975 magnetometer and
BMP085 pressure sensor
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch enables thermal sensors and QFPROM support for qcom platforms.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch enables configs required to get SATA functionality working on
IFC6410 board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
IFC6410 board has PCIE based ATL1C ethernet controller, so enable related configs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable support for clocks, controlled by the RPM processor on
Qualcomm platforms.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The Axentia TSE-850 is a SAMA5D3-based device designed to generate
FM subcarrier signals.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
We have upstream support for ftgmac100 ethernet with NCSI, GPIO, pinmux,
and IPMI BT. Enable these for both g4 and g5 platforms.
Signed-off-by: Joel Stanley <joel@jms.id.au>
This enables PWM and the TI ECAP and EHRWPM modules. These are used on LEGO
MINDSTORMS EV3.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This enables the DA8xx pinconf driver by default. It is needed by LEGO
MINDSTORMS EV3.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Enable:
* Recently added Enable r8a774[35] SoCs
* CMA for DMA to allow use of VIN with large frame sizes
* CONFIG_VIDEO_ADV7604 to allow use of HDMI input
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYb3wlAAoJENfPZGlqN0++P8oP/iyhFrcWs0h3L2fJWfn1zP/N
2LB0PdGtzgoeJbY6pCbWE1ujegNE+GAb9TDw9IvOGPv35sd5BJjUal01bD3ZM1Ct
tngHJ3OyWDI3jAlEkwiHesxoa60PxB/bFy/M3TZu9vBStEbVs6uBjiv8woCPhxhV
ZDKu++St+PYUAmEvYbt+TA+la2ZAmZwfrSSnrkvZvhBT2oTYIobMm1wHfjCRkrtv
NBMV6KwfgQTtS2iVIwES/4zYoFDdbt8qk2saB4fscBnQzml4ueFaO8INfefilBcx
x/1ky48QYSNVIDcZ5aNS/KBgP3vRNozoemF/ehArj0ZK/K/i5QoqtYl/vVQHf7An
KgETb33jh1+yb6AA1NxG4BcGPoWhTIw+SI6gTbdtfETNSoxF5PQhLAehl+EiC6OT
NUdjgQd4xgqq8KsSQxfP1vs+F+l1OsssuQkfJ51CEm2u+0wdXNsZO4P5B6QAOsYV
e9EB1yJDbOwJkmsN7tHxcQhp6SjzHZ879y64h7izh+lu6FtyOrE/twRyOMxadVZG
eNIXbPiIcYBhOj5EEfweUOqZg7B0YnFxAnbZ4EPnfK4ieDnKYr6XgoDAU2umLb0J
b/Hj/ZWN8dnCdOgn3I8LIPkc+GGhiDqK3gNYMSdOlVlOT2JsvA3KD3882rDXdhAu
Acy96jpmJG8jiRq8qmHB
=4Ph/
-----END PGP SIGNATURE-----
Merge tag 'renesas-defconfig-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/defconfig
Renesas ARM Based SoC Defconfig Updates for v4.11
Enable:
* Recently added Enable r8a774[35] SoCs
* CMA for DMA to allow use of VIN with large frame sizes
* CONFIG_VIDEO_ADV7604 to allow use of HDMI input
* tag 'renesas-defconfig-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: multi_v7_defconfig: Enable r8a774[35] SoCs
ARM: shmobile: defconfig: Enable r8a774[35] SoCs
ARM: shmobile: defconfig: Enable CMA for DMA
ARM: shmobile: defconfig: Enable CONFIG_VIDEO_ADV7604
Signed-off-by: Olof Johansson <olof@lixom.net>
The PXA defconfig compiles the legacy MPU3050 driver as a module,
but the device does not appear in device trees nor board files, so
remove this from the defconfig assuming it was a mistake to add it
in the first place.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Tegra is currently configured to use the old input driver for the
MPU-3050. Switch to the new IIO driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The multi_v7 config enable the MPU3050 gyro input driver, but
there is now a dedicated IIO gyro driver for the same component,
which is the right subsystem to handle this. Replace it in the
defconfig. As we want the full IIO featureset and as other v7
systems will likely enjoy using IIO for their sensor work (such
as the Android-to-IIO userspace HAL), we take this opportunity to
turn on the standard sensor HRtimer triggering.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch enables the Qualcomm RPM based Clock Controller present on
A-family boards.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
ADC driver depends on REGULATOR and IIO that are not yet selected.
Current hardware boards (like stm32f429i-eval) is using fixed
regulators.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This enables the pwm-beeper module. This is used by the speaker on LEGO
MINDSTORMS EV3.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
All the Keystone 2 SoCs have an on-chip RAM called the MultiCore
Shared Memory (MSM) RAM managed by the Multicore Shared Memory
Controller (MSMC) that provides faster access compared to normal
DDR.
This patch enables the Generic on-chip SRAM driver that manages
this memory in software.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The OMAP2 plus defconfig lists the LIS3LC02D MISC driver
but there is nowadays a proper IIO driver for this accelerometer.
Switch the config to the new driver.
The IIO software triggers are helpful when using these devices
without a dedicated IRQ line, so activate those too.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MARVELL_PHY - support for the Marvell PHY that is on most of the devkits
EEPROM_AT24 - support for I2C EEPROMs on the devkits
GPIO_ALTERA - support for Altera's GPIO driver
NAND - support for the Denali NAND controller along with MTD subsystem
SPI_DESIGNWARE - support for SPI that is on SoCFPGA
SPI_DW_MMIO - support for the memory-mapped io interface for the DW SPI core
OF_CONFIGFS - SoCFPGA makes use of DT overlays using configfs, enable it
GPIO_ALTERA_A10SR - support for the newly added Altera HWMON driver
LEDS - support for the GPIO LEDs on the SoCFPGA devkits
RTC - support for the DS1307 RTC
JFFS2_FS - support for the JFFS2 filesystem
NFS_V4 - supports for v4 NFS
FUNCTION_TRACER - supports debug function tracing
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
To be able to use VIN with larger frame sizes CMA memory are needed for
DMA. If this is not enabled trying to capture large frames can result in
errors such as:
rcar-vin e6ef0000.video: dma_alloc_coherent of size 8388608 failed
A CMA area of 64MB are needed for v4l2-compliance to pass on all formats
on the largest possible frame size of 2048x2048.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The adv7612 is used on Gen2 boards (Lager, Koelsch and Gose) for HDMI
input. Enable support for this chip in shmobile_defconfig.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables the dumb-vga-dac driver by default for davinci boards.
The driver is needed for tilcdc support on da850-lcdk board.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Select CONFIG_CFG80211_WEXT so that wireless can work out of the box
when using userspace tools such as 'iwconfig'.
Generated by manually selecting CONFIG_CFG80211_WEXT and
then running:
make savedefconfig
cp defconfig arch/arm/configs/imx_v6_v7_defconfig
, which results in additional cleanup.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable media support and V4L2 capture, along with video decoders used
on da850 platforms.
Tested on da850-lcdk.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This enables CONFIG_THERMAL_OF by default for sunxi_defconfig. It is
required to get Allwinner SoCs' temperature from the GPADC driver.
The Allwinner SoCs all have an ADC that can also act as a touchscreen
controller and a thermal sensor. The first four channels can be used
either for the ADC or the touchscreen and the fifth channel is used for
the thermal sensor.
The thermal sensor requires the IP to be in touchscreen mode to return
correct values. Therefore, if the user is continuously reading the ADC
channel(s), the thermal framework in which the thermal sensor is
registered will switch the IP in touchscreen mode to get a temperature
value and requires a delay of 100ms (because of the mode switching),
then the ADC will switch back to ADC mode and requires also a delay of
100ms. If the ADC readings are critical to user and the SoC temperature
is not, the GPADC driver is capable of not registering the thermal
sensor in the thermal framework and thus, "quicken" the ADC readings. In
most use cases, the SoC temperature is more critical (for cpu throttling
for example or activating cooling devices) than ADC readings, thus it is
now enabled by default.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
NF_CT_PROTO_DCCP/SCTP/UDPLITE were switched from tristate to boolean so
defconfig needs to be adjusted to silence warnings:
warning: symbol value 'm' invalid for NF_CT_PROTO_DCCP
warning: symbol value 'm' invalid for NF_CT_PROTO_SCTP
warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Prior to Nikolay's commit dcd87999d, libnss-mdns (eg. to resolve
"foo.local" on the LAN using mDNS) worked without CONFIG_IP_MULTICAST
defined, but dcd87999d caused it to stop working without having
CONFIG_IP_MULTICAST defined explicitly.
Since exynos_defconfig did not previously define CONFIG_IP_MULTICAST,
mDNS used to work for users building with just exynos_defconfig, but
stopped working from dcd87999d.
Define CONFIG_IP_MULTICAST explicitly in exynos_defconfig as it appears
essential anyway.
Signed-off-by: Robie Basak <robie@justgohome.co.uk>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Defconfig additions, removals, etc. Most of these are small changes adding
the options for newly upstreamed drivers, or drivers needed for new board
support.
Bartlomiej Zolnierkiewicz has done a series of patches reducing the use
of CONFIG_IDE from 19 to 3 in favor of CONFIG_ATA.
Overall more patches than usual, but nothing big.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2XsL
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"Defconfig additions, removals, etc. Most of these are small changes
adding the options for newly upstreamed drivers, or drivers needed for
new board support.
Bartlomiej Zolnierkiewicz has done a series of patches reducing the
use of CONFIG_IDE from 19 to 3 in favor of CONFIG_ATA.
Overall more patches than usual, but nothing big"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: davinci_all_defconfig: Enable da8xx usb otg
ARM: defconfig: drop GPIO_SYSFS on multiplatforms
ARM: multi_v7_defconfig: enable STMicroelectronics HVA driver
ARM: configs: Add new config fragment to change RAM start point
ARM: davinci_all_defconfig: Enable OHCI as module
ARM: defconfig: turn on the DT cpufreq for Integrator
ARM: omap2plus_defconfig: Run make savedefconfig to save some space
ARM: davinci_all_defconfig: add missing options for systemd
ARM: davinci_all_defconfig: enable the mstpri and ddrctl drivers
ARM: bcm2835: add thermal driver to default config
ARM: omap2plus_defconfig: Enable LP873X support
ARM: omap2plus_defconfig: Enable REGULATOR_GPIO
ARM: omap2plus_defconfig: Enable TOUCHSCREEN_TSC2004
ARM: socfpga_defconfig: enable FS configs to support Angstrom filesystem
ARM: config: Enable GPIO Key driver in stm32_defconfig
ARM: tegra: Enable GMI driver in default configuration
ARM: tegra: Enable SGTL5000 audio
ARM: tegra: Update default configuration for v4.9-rc1
ARM: socfpga: updates for socfpga_defconfig
ARM: davinci_all_defconfig: enable LED default-on trigger
...
Introduces remoteproc "subdevice" support, which allows remoteproc
driver to associate devices to the "running" state of the remoteproc,
allowing devices to be probed and removed as the remote processor is
booted, shut down or recovering from a crash.
Handling of virtio device resources was improved, vring memory is now
allocated as part of other memory allocation. This ensures that all
vrings for all virtio devices are allocated before we boot the remote
processor.
The debugfs mechanism for starting and stopping remoteproc instances was
replaced with a sysfs interface, also providing a mechanism for
specifying firmware to use by the instance. This allows user space to
load and boot use case specific firmware on remote processors.
New drivers for the ST Slimcore and Qualcomm Hexagon DSP as well as
removal of the unused StE modem loader.
Finally support for crash recovery in the Qualcomm Wirelss subsystem
(used for WiFi/BT/FM on a number of platforms) and a number of bug fixes
and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/1kU
-----END PGP SIGNATURE-----
Merge tag 'rproc-v4.10' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
- introduce remoteproc "subdevice" support, which allows remoteproc
driver to associate devices to the "running" state of the remoteproc,
allowing devices to be probed and removed as the remote processor is
booted, shut down or recovering from a crash.
- handling of virtio device resources was improved, vring memory is now
allocated as part of other memory allocation. This ensures that all
vrings for all virtio devices are allocated before we boot the remote
processor.
- the debugfs mechanism for starting and stopping remoteproc instances
was replaced with a sysfs interface, also providing a mechanism for
specifying firmware to use by the instance. This allows user space to
load and boot use case specific firmware on remote processors.
- new drivers for the ST Slimcore and Qualcomm Hexagon DSP as well as
removal of the unused StE modem loader.
- finally support for crash recovery in the Qualcomm Wirelss subsystem
(used for WiFi/BT/FM on a number of platforms) and a number of bug
fixes and cleanups
* tag 'rproc-v4.10' of git://github.com/andersson/remoteproc: (49 commits)
remoteproc: qcom_adsp_pil: select qcom_scm
remoteproc: Drop wait in __rproc_boot()
remoteproc/ste: Delete unused driver
remoteproc: Remove "experimental" warning
remoteproc: qcom_adsp_pil: select qcom_scm
dt-binding: soc: qcom: smd: Add label property
remoteproc: qcom: mdt_loader: add include for sizes
remoteproc: Update last rproc_put users to rproc_free
remoteproc: qcom: adsp: Add missing MODULE_DEVICE_TABLE
remoteproc: wcnss-pil: add QCOM_SMD dependency
dmaengine: st_fdma: Revert: "Revert: Update st_fdma to 'depends on REMOTEPROC'"
remoteproc: Add support for xo clock
remoteproc: adsp-pil: fix recursive dependency
remoteproc: Introduce Qualcomm ADSP PIL
dt-binding: remoteproc: Introduce ADSP loader binding
remoteproc: qcom_wcnss: Fix circular module dependency
remoteproc: Merge table_ptr and cached_table pointers
remoteproc: Remove custom vdev handler list
remoteproc: Update max_notifyid as we allocate vrings
remoteproc: Decouple vdev resources and devices
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=4k30
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
- userspace LED class driver - it can be useful for testing triggers
and can also be used to implement virtual LEDs
- LED class driver for NIC78bx device
- LED core fixes for preventing potential races while setting
brightness when software blinking is enabled
- improvements in LED documentation to mention semantics on changing
brightness while trigger is active
* tag 'leds_for_4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: pca955x: Add ACPI support
leds: netxbig: fix module autoload for OF registration
leds: pca963x: Add ACPI support
leds: leds-cobalt-raq: use builtin_platform_driver
led: core: Fix blink_brightness setting race
led: core: Use atomic bit-field for the blink-flags
leds: Add user LED driver for NIC78bx device
leds: verify vendor and change license in mlxcpld driver
leds: pca963x: enable low-power state
leds: pca9532: Use default trigger value from platform data
leds: pca963x: workaround group blink scaling issue
cleanup LED documentation and make it match reality
leds: lp3952: Export I2C module alias information for module autoload
leds: mc13783: Fix MC13892 keypad led access
ledtrig-cpu.c: fix english
leds/leds-lp5523.txt: make documentation match reality
tools/leds: Add uledmon program for monitoring userspace LEDs
leds: Use macro for max device node name size
leds: Introduce userspace LED class driver
mfd: qcom-pm8xxx: Clean up PM8XXX namespace
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SQob
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.10/defconfig-4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/defconfig
Enable support for MUSB based USB OTG on DA850.
* tag 'davinci-for-v4.10/defconfig-4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci_all_defconfig: Enable da8xx usb otg
Signed-off-by: Olof Johansson <olof@lixom.net>
The musb driver is enabled but the phy and the glue
for the da8xx are not enabled.
Enable them.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Enable HVA (Hardware Video Accelerator) video encoder
driver for STMicroelectronics SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DIwx
-----END PGP SIGNATURE-----
Merge tag 'sti-defconfig-for-4.10-round3' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into next/defconfig
Pull "STi defconfig fix" from Patrice Chotard:
Enable HVA (Hardware Video Accelerator) video encoder
driver for STMicroelectronics SoC.
* tag 'sti-defconfig-for-4.10-round3' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: multi_v7_defconfig: enable STMicroelectronics HVA driver
The sysfs ABI to GPIO is marked obsolete and should not be
encouraged. Users should be encouraged to switch to using the
character device.
Let's begin by removing it from the multi defconfigs. Then
as time goes by I can aggressively remove it from other
defconfigs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
pull the following:
- Florian updates the multi_v7_defconfig with the relevant basic drivers needed
for the Broadcom BCM5301x (Northstar) SoCs to reboot, have PCIe, and Ethernet
- Martin enables the Raspberry Pi thermal driver in bcm2835_defconfig
-----BEGIN PGP SIGNATURE-----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=Tf8a
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.10/defconfig' of http://github.com/Broadcom/stblinux into next/defconfig
Pull "Broadcom defconfig changes for 4.10" from Florian Fainelli:
This pull request contains Broadcom ARM-based defconfig changes for 4.10, please
pull the following:
- Florian updates the multi_v7_defconfig with the relevant basic drivers needed
for the Broadcom BCM5301x (Northstar) SoCs to reboot, have PCIe, and Ethernet
- Martin enables the Raspberry Pi thermal driver in bcm2835_defconfig
* tag 'arm-soc/for-4.10/defconfig' of http://github.com/Broadcom/stblinux:
ARM: bcm2835: add thermal driver to default config
ARM: multi_v7_defconfig: Enable BCM47xx/BCM5301x drivers
defconfig.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pEwL
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.10/defconfig-3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/defconfig
Pull "DaVinci defconfig updates for v4.10 (part 3)" from Sekhar Nori:
Enables newly introduced DDR controller and
master priority setting drivers in kernel.
Also, update defconfig to boot latest systemd
based filesystems on DA850.
A patch enabling USB OHCI support in davinci
defconfig.
* tag 'davinci-for-v4.10/defconfig-3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci_all_defconfig: Enable OHCI as module
ARM: davinci_all_defconfig: add missing options for systemd
ARM: davinci_all_defconfig: enable the mstpri and ddrctl drivers
Merge "IDE to PATA change in ARM defconfigs from Bartlomiej Zolnierkiewicz:
On Monday, October 31, 2016 07:14:13 PM Bartlomiej Zolnierkiewicz wrote:
> On Monday, October 31, 2016 03:46:22 PM Russell King - ARM Linux wrote:
> > On Wed, Oct 26, 2016 at 07:01:12PM +0200, Bartlomiej Zolnierkiewicz wrote:
> > > On Wednesday, July 13, 2016 04:37:31 PM Arnd Bergmann wrote:
> > > > I'd be fine with just getting a pull request with all the patches that
> > > > had no negative feedback and that were not already applied (if any).
> > >
> > > Here it is (sorry for taking so long).
> >
> > I've just been digging in the dmesg logs from when I was using the
> > Assabet+Neponset as my firewall, and it was having to use the IDE
> > ide-cs driver rather than the pata pcmcia driver.
> >
> > I don't recall whether the pata pcmcia driver was a problem or not,
> > as the PCMCIA interface can't cope with _any_ 32-bit accesses. I
> > think PATA tries to use the "highest" possible access size by
> > default...
>
> It doesn't actually - it defaults to 16-bits for PIO data access and
> you must explicitly enable 32-bits using ATA_PFLAG_PIO32 port flag
> (pata_pcmcia doesn't set it so it should be okay). Also taskfile
> registers are accessed using 8-bits access by default transport
> functions (which are used by pata_pcmcia).
Please also note that:
- assebet_defconfig currently doesn't even enable ide-cs
(CONFIG_BLK_DEV_IDECS) in the mainline kernel
- neponset_defconfig doesn't even enable IDE (CONFIG_IDE)
in the mainline kernel
so there is no risk of breaking anything..
* 'v4.9-rc2-arm-configs-pata' of https://github.com/bzolnier/linux:
arm: spitz_defconfig: convert to use libata PATA drivers
arm: s3c2410_defconfig: convert to use libata PATA drivers
arm: netwinder_defconfig: convert to use libata PATA drivers
arm: jornada720_defconfig: convert to use libata PATA drivers
arm: ixp4xx_defconfig: convert to use libata PATA drivers
arm: h3600_defconfig: convert to use libata PATA drivers
arm: corgi_defconfig: convert to use libata PATA drivers
arm: am200epdkit_defconfig: convert to use libata PATA drivers
arm: omap1_defconfig: convert to use libata PATA drivers
arm: collie_defconfig: convert to use libata PATA drivers
arm: shannon_defconfig: disable IDE subsystem
arm: mainstone_defconfig: disable IDE subsystem
arm: lart_defconfig: disable IDE subsystem
arm: cerfcube_defconfig: disable IDE subsystem
arm: badge4_defconfig: disable IDE subsystem
arm: assabet_defconfig: disable IDE subsystem
Enable the davinci ohci driver as a module for usb
tested with the omap138-lcdk board.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The Kconfig and file naming for the PM8xxx driver is totally
confusing:
- Kconfig options MFD_PM8XXX and MFD_PM8921_CORE, some in-kernel
users depending on or selecting either at random.
- A driver file named pm8921-core.c even if it is indeed
used by the whole PM8xxx family of chips.
- An irqchip named pm8xxx since it was (I guess) realized that
the driver was generic for all pm8xxx PMICs.
As I may want to add support for PM8901 this is starting to get
really messy. Fix this situation by:
- Remove the MFD_PM8921_CORE symbol and rely solely on MFD_PM8XXX
and convert all users, including LEDs Kconfig and ARM defconfigs
for qcom and multi_v7 to use that single symbol.
- Renaming the driver to qcom-pm8xxx.c to fit along the two
other qcom* prefixed drivers.
- Rename functions withing the driver from 8921 to 8xxx to
indicate it is generic.
- Just drop the =m config from the pxa_defconfig, I have no clue
why it is even there, it is not a Qualcomm platform. (Possibly
older Kconfig noise from saveconfig.)
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Enable audio support for various Toradex devices as well as the GMI.
-----BEGIN PGP SIGNATURE-----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=zelz
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.10-arm-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/defconfig
ARM: tegra: Default configuration updates for v4.10-rc1
Enable audio support for various Toradex devices as well as the GMI.
* tag 'tegra-for-4.10-arm-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Enable GMI driver in default configuration
ARM: tegra: Enable SGTL5000 audio
ARM: tegra: Update default configuration for v4.9-rc1
Signed-off-by: Olof Johansson <olof@lixom.net>
- Enable tsc2004 touchscreen as a loadable module
- Enable REGULATOR_GPIO, dra71-evm needs this for MMC voltage
- Enable LP873x PMICs for dra71x-evm
- Run make savedefconfig to save some space and make it
easier to generate minimal patches against it
-----BEGIN PGP SIGNATURE-----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=h0e5
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.10/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/defconfig
Defconfig changes for omaps for v4.10 merge window:
- Enable tsc2004 touchscreen as a loadable module
- Enable REGULATOR_GPIO, dra71-evm needs this for MMC voltage
- Enable LP873x PMICs for dra71x-evm
- Run make savedefconfig to save some space and make it
easier to generate minimal patches against it
* tag 'omap-for-v4.10/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2plus_defconfig: Run make savedefconfig to save some space
ARM: omap2plus_defconfig: Enable LP873X support
ARM: omap2plus_defconfig: Enable REGULATOR_GPIO
ARM: omap2plus_defconfig: Enable TOUCHSCREEN_TSC2004
Signed-off-by: Olof Johansson <olof@lixom.net>
Two patches to enable the dumb VGA bridges in the multi_v7 and sunxi
defconfig.
-----BEGIN PGP SIGNATURE-----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=P4mc
-----END PGP SIGNATURE-----
Merge tag 'sunxi-defconfig-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/defconfig
Allwinner defconfig changes for 4.10
Two patches to enable the dumb VGA bridges in the multi_v7 and sunxi
defconfig.
* tag 'sunxi-defconfig-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: multi_v7: enable VGA bridge
ARM: sunxi: Enable VGA bridge
Signed-off-by: Olof Johansson <olof@lixom.net>
- Increase CMA size to 64 MiB, so that we can use etnaviv driver with
1920x1080 display devices.
- Enable ES8328 codec driver support, which is required by Kosagi
Novena boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYKrrAAAoJEFBXWFqHsHzOj4EH/2hdhqbgnOXkYfxU1vp+Pic1
n3CAeRwtgIkfVWRxPn0ljx3XUppqnkGbTtn0JcgNDiPJnmiwhdPdVzUaekw+HVXL
kGp3O7gxnop7txSsCuMy6jFJxIpPPO0eiH8j0NfYv1WqjFo/6lJJmCaowxoEEKXn
T51/e7+W76WR294JruYDTgtDYHXphX58gI1vqAs/2r/wDFxThkxGSDQlNq8edrA7
dtP1urqDR6Q99eeA4gBNl/xqkN0NOKImf7wM05Pvyf5uRzVtHiYBhl3/3x2wgcsF
u9sehmu8vFPaifYbCoczxcRmiJew1ZAg0LdrFh1BJMnKRxbTVOl4NGPKYxALRT8=
=vMwU
-----END PGP SIGNATURE-----
Merge tag 'imx-defconfig-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/defconfig
i.MX defconfig updates for 4.10:
- Increase CMA size to 64 MiB, so that we can use etnaviv driver with
1920x1080 display devices.
- Enable ES8328 codec driver support, which is required by Kosagi
Novena boards.
* tag 'imx-defconfig-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: Select the es8328 codec driver
ARM: imx_v6_v7_defconfig: Increase CMA size
Signed-off-by: Olof Johansson <olof@lixom.net>
The Integrators are now migrated to handle the CPUfreq
scaling using the generic devicetree CPUfreq driver using the
common clock framework and have the required device tree
modifications, so turn off the old driver and turn on the new
generic driver.
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'sti-defconfig-for-4.10-round2' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: multi_v7_defconfig: Remove ST_THERMAL_SYSCFG Kconfig symbol
Signed-off-by: Olof Johansson <olof@lixom.net>
This shrinks down omap2plus_defconfig a bit and makes it easier for
people to generate minimal patches against it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some kernel configuration options required for systemd
support are missing in davinci_all_defconfig. Add them.
This is based on recommendations in:
http://cgit.freedesktop.org/systemd/systemd/tree/README
Options which kernel enables by default (and will thus be removed
upon next savedefconfig update) are not included.
Tested on OMAP-L138 LCDK board with fully up to date armv5
archlinux filesystem.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
With the da8xx memory controller and master peripheral priority
drivers merged and corresponding device tree changes in place we can
now enable appropriate options by default.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add the thermal driver to list of compiled modules in the default
config for bcm2835.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
LP873X family of PMICs are used in dra71x-evm, So enable the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO regulator is used on dra71-evm platform to control MMCSD IO
voltage
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LogicPD DM3730 Torpedo and SOM-LV devices have the TI
TSC2004 touchscreen controller. Enable the related driver as
a module.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
systemd on the Angstrom root file system expects AUTOFS to be configured
as a module and NFSD to be statically linked into the kernel. This patch
adds the necessary configuration to get rid two "FAILED" error messages
during systemd startup.
Signed-off-by: Matthew Gerlach <mgerlach@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v2: provide a more descriptive changelog
The NVIDIA Tegra 3 aka T30 based Apalis T30 and Colibri T30 as well as
the new Tegra K1 aka TK1 based Apalis TK1 modules contain a Freescale
SGTL5000 analogue audio codec.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Regenerate the default configuration on top of v4.9-rc1. This shuffles
around a couple of symbols and drops some that have become defaults or
which were dropped.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch enables the following in the
socfpga_defconfig:
+CONFIG_OF_OVERLAY=y
Enable support for Device Tree Overlays
+CONFIG_FPGA_REGION=y
Enable device tree overlay support for FPGA
programming
+CONFIG_FPGA_MGR_SOCFPGA_A10=y
Enable partial reconfiguration for Altera
Arria 10 FPGA
+CONFIG_FPGA_BRIDGE=y
Enable the FPGA Bridges framework
+CONFIG_SOCFPGA_FPGA_BRIDGE=y
Enable support for SoCFPGA hardware
bridges
+CONFIG_ALTERA_FREEZE_BRIDGE=y
Enable support for the Altera Soft IP
Freeze bridges
Signed-off-by: Alan Tull <atull@opensource.altera.com>
The LEDs default-on trigger is nice to have. For example, it can be used
to configure a LED as a power indicator.
Signed-off-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: build as module, subject line fixes]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This changes the davinci default configuration to build the davinci
MMC driver into the kernel. This allows booting from an SD card without
requiring an initrd containing the kernel module.
Signed-off-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: minor commit message adjustments]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The gpio-poweroff driver is needed by LEGO MINDSTORMS EV3 (AM1808 based
board).
Signed-off-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: subject line adjustment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
With the device tree changes for tilcdc in place, we can now enable
the driver by default in the davinci_all defconfig file.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
As STiH415/416 have been removed from kernel, remove IPs only found
on these socs, remove CONFIG_PHY_MIPHY365X and CONFIG_PHY_STIH41X_USB.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYCN27AAoJEMrHeC97M/+m7PwQAIVn/UpHkG9RJCfMG0Fk1M6S
PdpDcdRmB/6tEN0rInzvQbQEr+UZfZEL5wWWvwp3YgQqPOL1dCALQr91qEvj1CC1
OesmqqXCCUiC8sNVz9ctugYh6XDybsAEAtpuPnueVX7VMUqSqgczPOlGJaxsHMPo
5ySzEETIvvBAFxJUpBOecZNS5LPHOhLw4MH/0eHmFntVmVME/a6Uvu/A2uIkdRed
54K5Clg5HSArPY/+fNorODnXNK3ny+h+EPpRvJySjGKFCCoM++ZfNd3XGp5Zf5Nj
CKJoVLqSbRL9yiuiUNZbjpEioX4Wh+rY1lh6n84exKVOTRC32MMELg5Woff/yagX
B/lnOmXXqJQbIrpTRPr5OZgketsdbmetus5KKOnL8JhbjrQeh09nfpwqxQ6oRZzv
pGMTwJS3HAfZ6rVlZ3k0n+tEyiMWWY5vwRKM/PDLM8ATdC7GNHs/hDPK8hejbzyS
QrJUIPzZLd98C7t5M24H+jqAd+WDNDETN8Lfx4ELnGFme7vUVqN/JOkqF88F1OC8
y/EetThjRFf7iwIrexNgJj17ZZ1/HSy2exrsRCtrO3bate2ZbWhWZqQYiqZJJPQo
48+CMc/F7h/e4cF943cWwxMkroQZIgnm7tdyrTAOadacPR892cLGHT8fxC1K127Q
NKuiFC71JmblnOYP/KHY
=5dHw
-----END PGP SIGNATURE-----
Merge tag 'sti-defconfig-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into next/defconfig
Remove STiH415/416 specific IPs
As STiH415/416 have been removed from kernel, remove IPs only found
on these socs, remove CONFIG_PHY_MIPHY365X and CONFIG_PHY_STIH41X_USB.
* tag 'sti-defconfig-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: multi_v7_defconfig: Remove stih41x phy Kconfig symbol.
ARM: multi_v7_defconfig: Remove miphy365 phy Kconfig symbol.
Signed-off-by: Olof Johansson <olof@lixom.net>
Some config options like perf events and PM are now implicit,
we have an upstream driver for the AK8974, and we really
want the HRTIMER software triggers from configfs with some
of the sensors.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts spitz_defconfig to use libata PATA
drivers.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts s3c2410_defconfig to use libata PATA
drivers.
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Vincent Sanders <vince@simtec.co.uk>
Cc: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts netwinder_defconfig to use libata PATA
drivers.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts jornada720_defconfig to use libata PATA
drivers.
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts ixp4xx_defconfig to use libata PATA
drivers.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khalasa@piap.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts h3600_defconfig to use libata PATA
drivers.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts corgi_defconfig to use libata PATA
drivers.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts am200epdkit_defconfig to use libata PATA
drivers.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts omap1_defconfig to use libata PATA
drivers.
Cc: linux-omap@vger.kernel.org
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts collie_defconfig to use libata PATA
drivers.
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
