When a device attached to the roothub is suspended, the endpoint rings
are stopped. The host may generate a completion event with the
completion code set to 'Stopped' or 'Stopped Invalid' when the ring is
halted. The current xHCI code prints a warning in that case, which can
be really annoying if the USB device is coming into and out of suspend.
Remove the unnecessary warning.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Stephen Hemminger <stephen@networkplumber.org>
Use proper macro while extracting TRB transfer length from
Transfer event TRBs. Adding a macro EVENT_TRB_LEN (bits 0:23)
for the same, and use it instead of TRB_LEN (bits 0:16) in
case of event TRBs.
This patch should be backported to kernels as old as 2.6.31, that
contain the commit b10de14211 "USB: xhci:
Bulk transfer support". This patch will have issues applying to older
kernels.
Signed-off-by: Vivek gautam <gautam.vivek@samsung.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This patch is to bind xhci root hub usb port with its acpi node.
The port num in the acpi table matches with the sequence in the xhci
extended capabilities table. So call usb_hcd_find_raw_port_number() to
transfer hub port num into raw port number which associates with
the sequence in the xhci extended capabilities table before binding.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
xhci driver divides the root hub into two logical hubs which work
respectively for usb 2.0 and usb 3.0 devices. They are independent
devices in the usb core. But in the ACPI table, it's one device node
and all usb2.0 and usb3.0 ports are under it. Binding usb port with
its acpi node needs the raw port number which is reflected in the xhci
extended capabilities table. This patch is to add find_raw_port_number
callback to struct hc_driver(), fill it with xhci_find_raw_port_number()
which will return raw port number and add a wrap usb_hcd_find_raw_port_number().
Otherwise, refactor xhci_find_real_port_number(). Using
xhci_find_raw_port_number() to get real index in the HW port status
registers instead of scanning through the xHCI roothub port array.
This can help to speed up.
All addresses in xhci->usb2_ports and xhci->usb3_ports array are
kown good ports and don't include following bad ports in the extended
capabilities talbe.
(1) root port that doesn't have an entry
(2) root port with unknown speed
(3) root port that is listed twice and with different speeds.
So xhci_find_raw_port_number() will only return port num of good ones
and never touch bad ports above.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
/home/b29397/work/code/git/linus/linux-2.6/drivers/usb/host/xhci-ring.c: In function ‘handle_port_status’:
/home/b29397/work/code/git/linus/linux-2.6/drivers/usb/host/xhci-ring.c:1580: warning: ‘hcd’ may be used uninitialized in this function
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
As reported by Jan, and others over the past few years, there is a
race condition caused by unix_release setting the sock->sk pointer
to NULL before properly marking the socket as dead/orphaned. This
can cause a problem with the LSM hook security_unix_may_send() if
there is another socket attempting to write to this partially
released socket in between when sock->sk is set to NULL and it is
marked as dead/orphaned. This patch fixes this by only setting
sock->sk to NULL after the socket has been marked as dead; I also
take the opportunity to make unix_release_sock() a void function
as it only ever returned 0/success.
Dave, I think this one should go on the -stable pile.
Special thanks to Jan for coming up with a reproducer for this
problem.
Reported-by: Jan Stancek <jan.stancek@gmail.com>
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix for TX lockup in IPoIB
- QLogic -> Intel update for qib driver
- Small static checker fix for qib
- Fix error path return value in cxgb4
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=SOee
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma fixes from Roland Dreier:
"Small batch of InfiniBand/RDMA fixes for 3.9:
- Fix for TX lockup in IPoIB
- QLogic -> Intel update for qib driver
- Small static checker fix for qib
- Fix error path return value in cxgb4"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: change QLogic to Intel
IB/ipath: Silence a static checker warning
IPoIB: Fix send lockup due to missed TX completion
RDMA/cxgb4: Fix error return code in create_qp()
Four patches for arm-soc this week:
- Kevin Hilman is no longer reachable under his previous email address.
He submitted the patch earlier, but nobody felt responsible to pick
it up.
- One Tegra fix for an incorect register address in device tree.
- IMX multiplatform support exposes a configuration option that
leads to unbootable kernels on all other machines and that needs
to depend on that platform.
- A nontrivial bug fix for the setup of the mxs video output.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F6UW
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Arnd Bergmann:
"Four patches for arm-soc this week:
- Kevin Hilman is no longer reachable under his previous email
address. He submitted the patch earlier, but nobody felt
responsible to pick it up.
- One Tegra fix for an incorect register address in device tree.
- IMX multiplatform support exposes a configuration option that leads
to unbootable kernels on all other machines and that needs to
depend on that platform.
- A nontrivial bug fix for the setup of the mxs video output."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: update email address for Kevin Hilman
ARM: tegra: fix register address of slink controller
ARM: imx: add dependency check for DEBUG_IMX_UART_PORT
ARM: video: mxs: Fix mxsfb misconfiguring VDCTRL0
Pull nfsd bugfixes from J Bruce Fields:
"Fixes for a couple mistakes in the new DRC code. And thanks to Kent
Overstreet for noticing we've been sync'ing the wrong range on stable
writes since 3.8."
* 'for-3.9' of git://linux-nfs.org/~bfields/linux:
nfsd: fix bad offset use
nfsd: fix startup order in nfsd_reply_cache_init
nfsd: only unhash DRC entries that are in the hashtable
We need to be careful when testing task->tk_waitqueue in
rpc_wake_up_task_queue_locked, because it can be changed while we
are holding the queue->lock.
By adding appropriate memory barriers, we can ensure that it is safe to
test task->tk_waitqueue for equality if the RPC_TASK_QUEUED bit is set.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org
With the addition of following patch:
fcf8058 cpufreq: Simplify cpufreq_add_dev()
cpufreq driver's .init() routine must initialize policy->cpus with
mask of all possible CPUs (Online + Offline) that share the clock.
Then the core would copy this mask onto policy->related_cpus and will
reset policy->cpus to carry only online cpus.
acpi-cpufreq driver wasn't updated with this assumption and so
sometimes when we try to hot[un]plug CPUs at run time, sysfs
directories get corrupted.
This patch fixes acpi-cpufreq driver against this corruption.
Reported-and-tested-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In cpufreq_stats_free_sysfs() we aren't balancing calls to
cpufreq_cpu_get() with cpufreq_cpu_put(). This will never let us have
ref count to policy->kobj as zero.
We will get a hang if somehow cpufreq_driver_unregister() is called.
And that can happen when we compile our driver as module and
insmod/rmmod it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
They are defined in coreboot (MSR_PLATFORM) and the other
one is already defined in msr-index.h.
Let's use those.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the correct pstate value to calculate the effective frequency.
References: https://bugzilla.redhat.com/show_bug.cgi?id=923942
Reported-by: Satish Balay <balay@fastmail.fm>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some VMs seem to try to implement some MSRs but not all the registers
the driver needs. Check to make sure all the MSR that we need are
available. If any of the required MSRs are not available refuse to
load.
References: https://bugzilla.redhat.com/show_bug.cgi?id=922923
Reported-by: Josh Stone <jistone@redhat.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull drm fixes from Dave Airlie:
"Exynos and Intel fixes.
The intel fixes are fairly straightforward, mostly reverts due to bugs
found. The exynos one is a big larger since they found some issues
with the G2D engine and iommu interaction, and needed to verify the
operations a lot better than they were previously, otherwise a user
app can just crash the kernel with an iommu fault."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
Revert "drm/i915: write backlight harder"
drm/i915: don't disable the power well yet
Revert "drm/i915: set TRANSCODER_EDP even earlier"
drm/exynos: Check g2d cmd list for g2d restrictions
drm/exynos: Add a new function to get gem buffer size
drm/exynos: Deal with g2d buffer info more efficiently
drm/exynos: Clean up some G2D codes for readability
drm/exynos: Fix G2D core malfunctioning issue
drm/exynos: clear node object type at gem unmap
drm/exynos: Fix error routine to getting dma addr.
drm/exynos: Replaced kzalloc & memcpy with kmemdup
drm/exynos: fimd: calculate the correct address offset
drm/exynos: Make mixer_check_timing static
drm/exynos: modify the compatible string for exynos fimd
The FWNMI region is fixed at 0x7000 and the vector are now overflowing
that with allmodconfig. Fix that by moving slb_miss_realmode code out
of that region as it doesn't need to be that close to the call sites
(it is a _GLOBAL function)
Fixes this build error:
arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:1304: Error: attempt to move .org backwards
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Daniel writes:
"Just three revert/disable by default patches, one of them cc: stable
(since the offending commit was cc: stable, too)."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
Revert "drm/i915: write backlight harder"
drm/i915: don't disable the power well yet
Revert "drm/i915: set TRANSCODER_EDP even earlier"
Inki writes:
Includes bug fixes and code cleanups.
And it considers some restrictions to G2D hardware.
With this, the malfunction and page fault issues to g2d driver
would be fixed.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: Check g2d cmd list for g2d restrictions
drm/exynos: Add a new function to get gem buffer size
drm/exynos: Deal with g2d buffer info more efficiently
drm/exynos: Clean up some G2D codes for readability
drm/exynos: Fix G2D core malfunctioning issue
drm/exynos: clear node object type at gem unmap
drm/exynos: Fix error routine to getting dma addr.
drm/exynos: Replaced kzalloc & memcpy with kmemdup
drm/exynos: fimd: calculate the correct address offset
drm/exynos: Make mixer_check_timing static
drm/exynos: modify the compatible string for exynos fimd
On SACK reneging the sender immediately retransmits and forces a
timeout but disables Eifel (undo). If the (buggy) receiver does not
drop any packet this can trigger a false slow-start retransmit storm
driven by the ACKs of the original packets. This can be detected with
undo and TCP timestamps.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix for incorrect assignment of signed expression to unsigned variable.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I tried to set mac address of a bridge interface to a mac
address which already learned on this bridge, I got system hang.
The cause is straight forward: function br_fdb_change_mac_address
calls fdb_insert with NULL source nbp. Then an fdb lookup is
performed. If an fdb entry is found and it's local, it's OK. But
if it's not local, source is dereferenced for printk without NULL
check.
Signed-off-by: Hong Zhiguo <honkiko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan_vid_del() could possibly free ->vlan_info after a RCU grace
period, however, we may still refer to the freed memory area
by 'grp' pointer. Found by code inspection.
This patch moves vlan_vid_del() as behind as possible.
Cc: Patrick McHardy <kaber@trash.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WARN_ON(in_interrupt()) in net_enable_timestamp() can get false
positive, in socket clone path, run from softirq context :
[ 3641.624425] WARNING: at net/core/dev.c:1532 net_enable_timestamp+0x7b/0x80()
[ 3641.668811] Call Trace:
[ 3641.671254] <IRQ> [<ffffffff80286817>] warn_slowpath_common+0x87/0xc0
[ 3641.677871] [<ffffffff8028686a>] warn_slowpath_null+0x1a/0x20
[ 3641.683683] [<ffffffff80742f8b>] net_enable_timestamp+0x7b/0x80
[ 3641.689668] [<ffffffff80732ce5>] sk_clone_lock+0x425/0x450
[ 3641.695222] [<ffffffff8078db36>] inet_csk_clone_lock+0x16/0x170
[ 3641.701213] [<ffffffff807ae449>] tcp_create_openreq_child+0x29/0x820
[ 3641.707663] [<ffffffff807d62e2>] ? ipt_do_table+0x222/0x670
[ 3641.713354] [<ffffffff807aaf5b>] tcp_v4_syn_recv_sock+0xab/0x3d0
[ 3641.719425] [<ffffffff807af63a>] tcp_check_req+0x3da/0x530
[ 3641.724979] [<ffffffff8078b400>] ? inet_hashinfo_init+0x60/0x80
[ 3641.730964] [<ffffffff807ade6f>] ? tcp_v4_rcv+0x79f/0xbe0
[ 3641.736430] [<ffffffff807ab9bd>] tcp_v4_do_rcv+0x38d/0x4f0
[ 3641.741985] [<ffffffff807ae14a>] tcp_v4_rcv+0xa7a/0xbe0
Its safe at this point because the parent socket owns a reference
on the netstamp_needed, so we cant have a 0 -> 1 transition, which
requires to lock a mutex.
Instead of refining the check, lets remove it, as all known callers
are safe. If it ever changes in the future, static_key_slow_inc()
will complain anyway.
Reported-by: Laurent Chavey <chavey@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Usecount bounds checking so we do not go below zero on
mux usecounts.
- Loop range checking in GPIO ranges in the DT range parser.
- Proper print in debugfs for pinconf state.
- Fix compilation bug in generic pinconf code.
- Minor bugfixes to abx500 and mvebu drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=9iL3
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"Here are a few pinctrl fixes for the v3.9 rc series:
- Usecount bounds checking so we do not go below zero on mux
usecounts.
- Loop range checking in GPIO ranges in the DT range parser.
- Proper print in debugfs for pinconf state.
- Fix compilation bug in generic pinconf code.
- Minor bugfixes to abx500 and mvebu drivers."
* tag 'pinctrl-fixes-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinmux: forbid mux_usecount to be set at UINT_MAX
pinctrl: mvebu: fix checking for SoC specific controls
pinctrl: generic: Fix compilation error
pinctrl: Print the correct information in debugfs pinconf-state file
pinctrl: abx500: Fix checking if pin use AlternateFunction register
gpio: fix wrong checking condition for gpio range
Pull x86 fixes from Peter Anvin:
"A collection of minor fixes, more EFI variables paranoia
(anti-bricking) plus the ability to disable the pstore either as a
runtime default or completely, due to bricking concerns."
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efivars: Fix check for CONFIG_EFI_VARS_PSTORE_DEFAULT_DISABLE
x86, microcode_intel_early: Mark apply_microcode_early() as cpuinit
efivars: Handle duplicate names from get_next_variable()
efivars: explicitly calculate length of VariableName
efivars: Add module parameter to disable use as a pstore backend
efivars: Allow disabling use as a pstore backend
x86-32, microcode_intel_early: Fix crash with CONFIG_DEBUG_VIRTUAL
x86-64: Fix the failure case in copy_user_handle_tail()
This reverts commit cf0a6584aa.
Turns out that cargo-culting breaks systems. Note that we can't revert
further, since
commit 770c12312a
Author: Takashi Iwai <tiwai@suse.de>
Date: Sat Aug 11 08:56:42 2012 +0200
drm/i915: Fix blank panel at reopening lid
fixed a regression in 3.6-rc kernels for which we've never figured out
the exact root cause. But some further inspection of the backlight
code reveals that it's seriously lacking locking. And especially the
asle backlight update is know to get fired (through some smm magic)
when writing specific backlight control registers. So the possibility
of suffering from races is rather real.
Until those races are fixed I don't think it makes sense to try
further hacks. Which sucks a bit, but sometimes that's how it is :(
References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18788.html
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47941
Tested-by: Takashi Iwai <tiwai@suse.de>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org (the reverted commit was cc: stable, too)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're still not 100% ready to disable the power well, so don't disable
it for now. When we disable it we break the audio driver (because some
of the audio registers are on the power well) and machines with eDP on
port D (because it doesn't use TRANSCODER_EDP).
Also, instead of just reverting the code, add a Kernel option to let
us disable it if we want. This will allow us to keep developing and
testing the feature while it's not enabled.
This fixes problems caused by the following commit:
commit d6dd9eb1d9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jan 29 16:35:20 2013 -0200
drm/i915: dynamic Haswell display power well support
References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18788.html
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit cc464b2a17.
The reason is that Takashi Iwai reported a regression bisected to this
commit:
http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18788.html
His machine has eDP on port D (usual desktop all-in-on setup), which
intel_dp.c identifies as an eDP panel, but the hsw ddi code
mishandles.
Closer inspection of the code reveals that haswell_crtc_mode_set also
checks intel_encoder_is_pch_edp when setting is_cpu_edp. On haswell
that doesn't make much sense (since there's no edp on the pch), but
what this function _really_ checks is whether that edp connector is on
port A or port D. It's just that on ilk-ivb port D was on the pch ...
So that explains why this seemingly innocent change killed eDP on port
D. Furthermore it looks like everything else accidentally works, since
we've never enabled eDP on port D support for hsw intentionally (e.g.
we still register the HDMI output for port D in that case).
But in retrospective I also don't like that this leaks highly platform
specific details into common code, and the reason is that the drm
vblank layer sucks. So instead I think we should:
- move the cpu_transcoder into the dynamic pipe_config tracking (once
that's merged).
- fix up the drm vblank layer to finally deal with kms crtc objects
instead of int pipes.
v2: Pimp commit message with the better diagnosis as discussed with
Paulo on irc.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull SCSI target fixes from Nicholas Bellinger:
"These are mostly minor fixes this time around. The iscsi-target CHAP
big-endian bugfix and bump FD_MAX_SECTORS=2048 default patch to allow
1MB sized I/Os for FILEIO backends on >= v3.5 code are both CC'ed to
stable.
Also, there is a persistent reservations regression that has recently
been reported for >= v3.8.x code, that is currently being tracked down
for v3.9."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/pscsi: Reject cross page boundary case in pscsi_map_sg
target/file: Bump FD_MAX_SECTORS to 2048 to handle 1M sized I/Os
tcm_vhost: Flush vhost_work in vhost_scsi_flush()
tcm_vhost: Add missed lock in vhost_scsi_clear_endpoint()
target: fix possible memory leak in core_tpg_register()
target/iscsi: Fix mutual CHAP auth on big-endian arches
target_core_sbc: use noop for SYNCHRONIZE_CACHE
- recent regressions in raid5
- recent regressions in dmraid
- a few instances of CONFIG_MULTICORE_RAID456 linger
Several tagged for -stable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=Rycs
-----END PGP SIGNATURE-----
Merge tag 'md-3.9-fixes' of git://neil.brown.name/md
Pull md fixes from NeilBrown:
"A few bugfixes for md
- recent regressions in raid5
- recent regressions in dmraid
- a few instances of CONFIG_MULTICORE_RAID456 linger
Several tagged for -stable"
* tag 'md-3.9-fixes' of git://neil.brown.name/md:
md: remove CONFIG_MULTICORE_RAID456 entirely
md/raid5: ensure sync and DISCARD don't happen at the same time.
MD: Prevent sysfs operations on uninitialized kobjects
MD RAID5: Avoid accessing gendisk or queue structs when not available
md/raid5: schedule_construction should abort if nothing to do.
Pull i2c fixes from Wolfram Sang:
"One bugfix for the tegra driver. Two updates regarding email
addresses and MAINTAINERS which I like to have up-to-date so people
can be reached immediately. While we are here, there is on PCI_ID
addition."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer entry for atmel i2c driver
i2c: Fix my e-mail address in drivers and documentation
i2c: iSMT: add Intel Avoton DeviceIDs
i2c: tegra: check the clk_prepare_enable() return value
Pull watchdog fixes from Wim Van Sebroeck:
"Fix a boot issues and correct the AcpiMmioSel bitmask in the
sp5100_tco watchdog device driver"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: sp5100_tco: Set the AcpiMmioSel bitmask value to 1 instead of 2
watchdog: sp5100_tco: Remove code that may cause a boot failure
When KMS has parsed an EDID "detailed timing", it leaves the frame rate
zeroed. Consecutive (debug-) output of that mode thus yields 0 for
vsync. This simple fix also speeds up future invocations of
drm_mode_vrefresh().
While it is debatable whether this qualifies as a -stable fix I'd apply
it for consistency's sake; drm_helper_probe_single_connector_modes()
does the same thing already for all probed modes.
Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
EDID spreads some values across multiple bytes; bit-fiddling is needed
to retrieve these. The current code to parse "detailed timings" has a
cut&paste error that results in a vsync offset of at most 15 lines
instead of 63.
See
http://en.wikipedia.org/wiki/EDID
and in the "EDID Detailed Timing Descriptor" see bytes 10+11 show why
that needs to be a left shift.
Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These changes modify the qib driver as part of acquiring
the InfiniBand assets of QLogic.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Vinit Agnihotri <vinit.abhay.agnihotri@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
I have a static checker which complains that 0x255 is too high for
the "dev->opstats[opcode]" array. It turns out that the hardware
has already validated the opcode at this point so it can't actually
overflow.
However, silencing the warning is good and this matches how the
opcode is treated in qib_ib_rcv() as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit f0dc117abd ("IPoIB: Fix TX queue lockup with mixed UD/CM
traffic") attempts to solve an issue where unprocessed UD send
completions can deadlock the netdev.
The patch doesn't fully resolve the issue because if more than half
the tx_outstanding's were UD and all of the destinations are RC
reachable, arming the CQ doesn't solve the issue.
This patch uses the IB_CQ_REPORT_MISSED_EVENTS on the
ib_req_notify_cq(). If the rc is above 0, the UD send cq completion
callback is called directly to re-arm the send completion timer.
This issue is seen in very large parallel filesystem deployments
and the patch has been shown to correct the issue.
Cc: <stable@vger.kernel.org>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix to return a negative error code from the error handling case
instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull NVMe driver update from Matthew Wilcox:
"These patches have mostly been baking for a few months; sorry I didn't
get them in during the merge window. They're all bug fixes, except
for the addition of the SMART log and the addition to MAINTAINERS."
* git://git.infradead.org/users/willy/linux-nvme:
NVMe: Add namespaces with no LBA range feature
MAINTAINERS: Add entry for the NVMe driver
NVMe: Initialize iod nents to 0
NVMe: Define SMART log
NVMe: Add result to nvme_get_features
NVMe: Set result from user admin command
NVMe: End queued bio requests when freeing queue
NVMe: Free cmdid on nvme_submit_bio error
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mqueue: sys_mq_open: do not call mnt_drop_write() if read-only
mm/hotplug: only free wait_table if it's allocated by vmalloc
dma-debug: update DMA debug API to better handle multiple mappings of a buffer
dma-debug: fix locking bug in check_unmap()
drivers/rtc/rtc-at91rm9200.c: use a variable for storing IMR
drivers/video/ep93xx-fb.c: include <linux/io.h> for devm_ioremap()
drivers/rtc/rtc-da9052.c: fix for rtc device registration
mm: zone_end_pfn is too small
poweroff: change orderly_poweroff() to use schedule_work()
mm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting
printk: Provide a wake_up_klogd() off-case
irq_work.h: fix warning when CONFIG_IRQ_WORK=n
mnt_drop_write() must be called only if mnt_want_write() succeeded,
otherwise the mnt_writers counter will diverge.
mnt_writers counters are used to check if remounting FS as read-only is
OK, so after an extra mnt_drop_write() call, it would be impossible to
remount mqueue FS as read-only. Besides, on umount a warning would be
printed like this one:
=====================================
[ BUG: bad unlock balance detected! ]
3.9.0-rc3 #5 Not tainted
-------------------------------------
a.out/12486 is trying to release lock (sb_writers) at:
mnt_drop_write+0x1f/0x30
but there are no more locks to release!
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
zone->wait_table may be allocated from bootmem, it can not be freed.
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Reviewed-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There were reports of the igb driver unmapping buffers without calling
dma_mapping_error. On closer inspection issues were found in the DMA
debug API and how it handled multiple mappings of the same buffer.
The issue I found is the fact that the debug_dma_mapping_error would
only set the map_err_type to MAP_ERR_CHECKED in the case that the was
only one match for device and device address. However in the case of
non-IOMMU, multiple addresses existed and as a result it was not setting
this field once a second mapping was instantiated. I have resolved this
by changing the search so that it instead will now set MAP_ERR_CHECKED
on the first buffer that matches the device and DMA address that is
currently in the state MAP_ERR_NOT_CHECKED.
A secondary side effect of this patch is that in the case of multiple
buffers using the same address only the last mapping will have a valid
map_err_type. The previous mappings will all end up with map_err_type
set to MAP_ERR_CHECKED because of the dma_mapping_error call in
debug_dma_map_page. However this behavior may be preferable as it means
you will likely only see one real error per multi-mapped buffer, versus
the current behavior of multiple false errors mer multi-mapped buffer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Reviewed-by: Shuah Khan <shuah.khan@hp.com>
Tested-by: Shuah Khan <shuah.khan@hp.com>
Cc: Jakub Kicinski <kubakici@wp.pl>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In check_unmap() it is possible to get into a dead-locked state if
dma_mapping_error is called. The problem is that the bucket is locked in
check_unmap, and locked again by debug_dma_mapping_error which is called
by dma_mapping_error. To resolve that we must release the lock on the
bucket before making the call to dma_mapping_error.
[akpm@linux-foundation.org: restore 80-col trickery to be consistent with the rest of the file]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Reviewed-by: Shuah Khan <shuah.khan@hp.com>
Tested-by: Shuah Khan <shuah.khan@hp.com>
Cc: Jakub Kicinski <kubakici@wp.pl>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some revisions of AT91 SoCs, the RTC IMR register is not working.
Instead of elaborating a workaround for that specific SoC or IP version,
we simply use a software variable to store the Interrupt Mask Register
and modify it for each enabling/disabling of an interrupt. The overhead
of this is negligible anyway.
The interrupt mask register (IMR) for the RTC is broken on the AT91SAM9x5
sub-family of SoCs (good overview of the members here:
http://www.eewiki.net/display/linuxonarm/AT91SAM9x5 ). The "user visible
effect" is the RTC doesn't work.
That sub-family is less than two years old and only has devicetree (DT)
support and came online circa lk 3.7 . The dust is yet to settle on the
DT stuff at least for AT91 SoCs (translation: lots of stuff is still
broken, so much that it is hard to know where to start).
The fix in the patch is pretty simple: just shadow the silicon IMR
register with a variable in the driver. Some older SoCs (pre-DT) use the
the rtc-at91rm9200 driver (e.g. obviously the AT91RM9200) and they should
not be impacted by the change. There shouldn't be a large volume of
interrupts associated with a RTC.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
