When using kgdb, you get an abort when accessing the UART registers.
This is because the driver has already entered runtime PM and so turned
off the bus clock needed to access the registers.
To fix this, set the capability indicating Runtime PM is active while idle.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I noticed that unused UARTs won't necessarily idle properly always
unless at least one byte tx transfer is done first.
After some debugging I narrowed down the problem to the scr register
dma configuration bits that need to be set before softreset for the
clocks to idle. Unless we do this, the module clkctrl idlest bits
may be set to 1 instead of 3 meaning the clock will never idle and
is blocking deeper idle states for the whole domain.
This might be related to the configuration done by the bootloader
or kexec booting where certain configurations cause the 8250 or
the clkctrl clock to jam in a way where setting of the scr bits
and reset is needed to clear it. I've tried diffing the 8250
registers for the various modes, but did not see anything specific.
So far I've only seen this on omap4 but I'm suspecting this might
also happen on the other clkctrl using SoCs considering they
already have a quirk enabled for UART_ERRATA_CLOCK_DISABLE.
Let's fix the issue by configuring scr before reset for basic dma
even if we don't use it. The scr register will be reset when we do
softreset few lines after, and we restore scr on resume. We should
do this for all the SoCs with UART_ERRATA_CLOCK_DISABLE quirk flag
set since the ones with UART_ERRATA_CLOCK_DISABLE are all based
using clkctrl similar to omap4.
Looks like both OMAP_UART_SCR_DMAMODE_1 | OMAP_UART_SCR_DMAMODE_CTL
bits are needed for the clkctrl to idle after a softreset.
And we need to add omap4 to also use the UART_ERRATA_CLOCK_DISABLE
for the related workaround to be enabled. This same compatible
value will also be used for omap5.
Fixes: cdb929e445 ("serial: 8250_omap: workaround errata around idling UART after using DMA")
Cc: Keerthy <j-keerthy@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Altera 16550 UART core supports FCR Rx Trigger Level setting,
but the port definition in the driver is missing the rxtrig_bytes
array specifying the trigger levels. Add the array to make the Rx
Trigger Level setting available on this type of 16550 UART.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "unthrottle_timeout" is HZ/10 but mod_timer() takes a the actual
jiffie where you want it to timeout, not an offset.
Fixes: 5909c0bf9c ("serial/aspeed-vuart: Implement quick throttle mechanism")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the 8250_of driver only supports MEM IO type
accesses.
Some development boards (Huawei D03, specifically) require
IO space access for 8250-compatible OF driver support, so
add it.
The modification is quite simple: just set the port iotype
and associated flags depending on the device address
resource type.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device->baud is always non zero value because it is checked already in
early_serial8250_setup() before init_port is called.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although we populate the ->throttle and ->unthrottle UART operations,
these may not be called until the ldisc has had a chance to schedule and
check buffer space. This means that we may overflow the flip buffers
without ever hitting the ldisc's throttle threshold.
This change implements an interrupt-based throttle, where we check for
space in the flip buffers before reading characters from the UART's
FIFO. If there's no space available, we disable the RX interrupt and
schedule a timer to check for space later.
For this, we need an unlocked version of the set_throttle function to be
able to change throttle state from the irq_handler, which already holds
port->lock.
This prevents a case where we drop characters under heavy RX load.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Tested-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The aspeed VUART runs at LPC bus frequency, rather than being restricted
to a typical UART baud rate. This means that the VUART can receive a lot
of data, which can overrun tty flip buffers, and/or cause a large amount
of interrupt traffic.
This change implements the uart_port->throttle & unthrottle callbacks,
implemented by disabling the receiver line status & received data
available IRQs.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Tested-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, we export serial8250_rx_chars, which does a whole bunch of
reads from the 8250 data register, without any form of flow control
between reads.
An upcoming change to the aspeed vuart driver implements more
fine-grained flow control in the interrupt handler, requiring
character-at-a-time control over the rx path.
This change exports serial8250_read_char to allow this.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Tested-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems IRQ lines between multiple UARTs might be shared. If so, the
irqflags have to be configured accordingly. The reason is: The 8250 port startup
code performs IRQ tests *before* the IRQ handler for that particular port is
registered. This is performed in serial8250_do_startup(). This function checks
whether IRQF_SHARED is configured and only then disables the IRQ line while
testing.
This test is performed upon each open() of the UART device. Imagine two UARTs
share the same IRQ line: On is already opened and the IRQ is active. When the
second UART is opened, the IRQ line has to be disabled while performing IRQ
tests. Otherwise an IRQ might handler might be invoked, but the the IRQ itself
cannot be handled, because the corresponding handler isn't registered,
yet. That's because the 8250 code uses a chain-handler and invokes the
corresponding port's IRQ handling rountines himself.
Unfortunately this IRQF_SHARED flag isn't configured for UARTs probed via device
tree even if the IRQs are shared. This way, the actual and shared IRQ line isn't
disabled while performing tests and the kernel correctly detects a spurious
IRQ. So, adding this flag to the DT probe solves the issue.
Note: The UPF_SHARE_IRQ flag is configured unconditionally. Therefore, the
IRQF_SHARED flag can be set unconditionally as well.
Example stacktrace by performing echo 1 > /dev/ttyS2 on a non-patched system:
|irq 85: nobody cared (try booting with the "irqpoll" option)
| [...]
|handlers:
|[<ffff0000080fc628>] irq_default_primary_handler threaded [<ffff00000855fbb8>] serial8250_interrupt
|Disabling IRQ #85
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable/Clear module level UART wakeup in UART_OMAP_WER register based on
return value of device_may_wakeup() in .suspend(). This allows
userspace to use sysfs to control the ability of UART to wakeup the
system from deep sleep state. Register is restored back in .startup()
call that happens as part of resume sequence.
With this patch, userspace can control UART wakeup capability via sysfs:
To enable wakeup capability:
echo enabled > /sys/class/tty/ttyXX/device/power/wakeup
For disabling wakeup capability:
echo disabled > /sys/class/tty/ttyXX/device/power/wakeup
Note that the UART wakeup events configured in the 8250 hardware only
work for idle modes that do not cut off power for the UART. For deeper
idle states, dedicated padconf wakeirqs must be used. Or in some cases
the UART RX pin can be remuxed to GPIO input if the GPIO block stays
powered.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous implementation has had a detrimental effect on devices using
high bitrates (bluetooth), as the fifo being non-empty for a single check
would result in a 10 µs delay.
Limit the change to devices with the new "marvell,armada-38x-uart"
compatible string. Also update the code to allow the first 1000 retries
to not perform a delay.
The maximum duration of retries has been increased to cover a worst-case
seen on the Armada 385 SoC. "dmesg ; resize", will fill the buffer with
text to output before doing a resize. At 9600 baud this took up to 13 ms
to flush all characters and avoid some getting lost.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for two MEN UARTs (16z025 and 16z057) to the
8250_men_mcb driver.
The 16z025 consists of up to four ports, the 16z057 has
exactly four ports. Apart from that, all of them share the
Port settings.
Signed-off-by: Michael Moese <mmoese@suse.de>
Reported-by: Ben Turner <ben.turner@21net.com>
Tested-by: Ben Turner <ben.turner@21net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Nuvoton UART is almost compatible with the 8250 driver when probed
via the 8250_of driver, however it requires some extra configuration
at startup.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Special settings for APMC0D08 are applied when device is present
in the system. To check its presence we may use acpi_dev_present()
instead of current open coded variant.
Cc: Feng Kan <fkan@apm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI ID database is for IDs used across several drivers.
Here is the case for SUNIX combo cards.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add PCI ids for two variants of Brainboxes UC-260 quad port
PCI serial cards.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not fail on multiport cards in serial_pci_is_class_communication().
It restores behaviour for SUNIX multiport cards, that enumerated by
class and have a custom board data.
Moreover it allows users to reenumerate port-by-port from user space.
Fixes: 7d8905d064 ("serial: 8250_pci: Enable device after we check black list")
Reported-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An issue has been observed on the Marvell Armada 38x serial port.
Writes to UART_LCR can result in characters that are currently held in the
TX FIFO being lost rather than sent, even if the userspace process has
attempted to flush them.
This is most visible when using the "resize" command (tested on Busybox),
where we have observed the escape code for restoring cursor position
becoming mangled.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap_8250_throttle() is called when tty RX buffer is about to overflow
and can no longer keep up with the rate at which UART is receiving data.
So, the expectation of this callback, is that UART stops RX and asserts
HW flow control to signal the sender to stop sending more data.
omap_8250_throttle() disables RX FIFO interrupts thus FIFO is no longer
serviced, leading to assertion of flow control once RX FIFO is full.
But, this does not work when DMA is enabled as driver keeps queuing new
RX DMA request in completion handler without brothering about throttling
request made by the higher layer.
This patch introduces a flag that can be used to determine whether or
not to queue next RX DMA request based on throttling request.
Without this patch, tty buffer overflows are reported at higher
baudrates.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, data in RX FIFO is read based on UART_LSR register state even
if RDI and RLSI interrupts are disabled in UART_IER register.
This is because when IRQ handler is called due to TX FIFO empty event,
RX FIFO is serviced based on UART_LSR register status instead of
UART_IIR status. This defeats the purpose of disabling UART RX
FIFO interrupts during throttling(see, omap_8250_throttle()) as IRQ
handler continues to drain UART RX FIFO resulting in overflow of buffer
at tty layer.
Fix this by making sure that driver drains UART RX FIFO only when
UART_IIR_RDI is set along with UART_LSR_BI or UART_LSR_DR bits.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exar sleep wake-up handling has been done on a per-channel basis by
virtue of INT0 being accessible from each channel's address space. I
believe this was initially done out of necessity, but now that Exar
devices have their own driver, we can do things more efficiently by
registering a dedicated INT0 handler at the PCI device level.
I see this change providing the following benefits:
1. If more than one port is active, eliminates the redundant bus
cycles for reading INT0 on every interrupt.
2. This note associated with hooking in the per-channel handler in
8250_port.c is resolved:
/* Fixme: probably not the best place for this */
Cc: Matt Schulte <matts@commtech-fastcom.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit
de9e33bdfa ("serial: 8250_dw: Improve clock rate setting")
obviously tries to cure symptoms, and not a root cause.
The root cause is the non-flexible rate calculation inside the
corresponding clock driver. What we need is to provide maximum UART
divisor value to the clock driver to allow it do the job transparently
to the caller.
Since from the initial commit message I have got no clue which clock
driver actually needs to be amended, I leave this exercise to the people
who know better the case.
Moreover, it seems [1] the fix introduced a regression. And possible
even one more [2].
Taking above, revert the commit de9e33bdfa for now.
[1]: https://www.spinics.net/lists/linux-serial/msg28872.html
[2]: https://github.com/Dunedan/mbp-2016-linux/issues/29#issuecomment-357583782
Fixes: de9e33bdfa ("serial: 8250_dw: Improve clock rate setting")
Cc: stable <stable@vger.kernel.org> # 4.15
Cc: Ed Blake <ed.blake@sondrel.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the devicetree, it is possible to specify the baudrate, parity,
bits, flow of the early console, by passing a configuration string like
this:
aliases {
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:57600n8";
};
This, for instance, will configure the early console for a baudrate of
57600 bps, no parity, and 8 bits per baud.
This patches implements parsing of this configuration string in the
8250_ingenic driver, which previously just ignored it.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The JZ4770 SoC's UART is no different from the other JZ SoCs, so this
commit simply adds the ingenic,jz4770-uart compatible string.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error pointer from devm_reset_control_get_optional_shared() is
not propagated.
One of the most common problem scenarios is it returns -EPROBE_DEFER
when the reset controller has not probed yet. In this case, the
probe of the reset consumer should be deferred.
Fixes: e2860e1f62 ("serial: 8250_of: Add reset support")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return a negative error code from the port register error
handling case instead of 0, as done elsewhere in this function.
Fixes: 39be40ce06 ("serial: 8250_uniphier: fix serial port index in private data")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed a spelling error in a comment.
Signed-off-by: Rolf Evers-Fischer <rolf.evers.fischer@aptiv.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there is no clock rate for uartclk defined, disable the previously
enabled clock again.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 23f5b3fdd0 serial: 8250_dw: only get the clock rate in one place
Signed-off-by: Stefan Potyra <Stefan.Potyra@elektrobit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using "make kvmconfig" results in a potentially unusable linux image
on s390. The reason is that both the (default on s390) sclp consoles
as well as the 8250 console register a ttyS<x> as console. Since there
will be no 8250 on s390 let's fence 8250. This will ensure that there
is always a working sclp console.
Reported-by: Alice Frosi <alice@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If either uartclk or baud are 0, avoid calculating and setting a divisor
based on them since the output will almost certainly be garbage.
This also allows platforms such as the MIPS generic kernel, which has no
way to know a valid BASE_BASE for the board it is actually booted on at
compile time, to set BASE_BAUD to 0 and avoid early_8250 setting a bad
divisor.
This fixes a regression caused by commit 31cb9a8575 ("earlycon:
initialise baud field of earlycon device structure"), which changed the
behavior of of_setup_earlycon such that it sets a baud rate in the
earlycon structure where previously it was left as 0. All boards
supported by the MIPS generic kernel started outputting garbage from the
boot console due to an incorrect divisor being set.
Fixes: 31cb9a8575 ("earlycon: initialise baud field of earlycon device structure")
Cc: stable <stable@vger.kernel.org> # 4.14
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device will be used in future Amazon EC2 instances as the primary
serial port (i.e., data sent to this port will be available via the
GetConsoleOuput [1] EC2 API).
[1] http://docs.aws.amazon.com/AWSEC2/latest/APIReference/API_GetConsoleOutput.html
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Matt Wilson <msw@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With all callbacks converted, and the timer callback prototype
switched over, the TIMER_FUNC_TYPE cast is no longer needed,
so remove it. Conversion was done with the following scripts:
perl -pi -e 's|\(TIMER_FUNC_TYPE\)||g' \
$(git grep TIMER_FUNC_TYPE | cut -d: -f1 | sort -u)
perl -pi -e 's|\(TIMER_DATA_TYPE\)||g' \
$(git grep TIMER_DATA_TYPE | cut -d: -f1 | sort -u)
The now unused macros are also dropped from include/linux/timer.h.
Signed-off-by: Kees Cook <keescook@chromium.org>
Here is the big tty/serial driver pull request for 4.15-rc1.
Lots of serial driver updates in here, some small vt cleanups, and a
raft of SPDX and license boilerplate cleanups, messing up the diffstat a
bit.
Nothing major, with no realy functional changes except better hardware
support for some platforms.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnD+w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynAmgCfSSr/9qiCE0vfP5eVYjddzxfWyZ4AoMbKORZC
5x2KVW0Btrbs3WmnD7ZU
=PSea
-----END PGP SIGNATURE-----
Merge tag 'tty-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big tty/serial driver pull request for 4.15-rc1.
Lots of serial driver updates in here, some small vt cleanups, and a
raft of SPDX and license boilerplate cleanups, messing up the diffstat
a bit.
Nothing major, with no realy functional changes except better hardware
support for some platforms.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (110 commits)
tty: ehv_bytechan: fix spelling mistake
tty: serial: meson: allow baud-rates lower than 9600
serial: 8250_fintek: Fix crash with baud rate B0
serial: 8250_fintek: Disable delays for ports != 0
serial: 8250_fintek: Return -EINVAL on invalid configuration
tty: Remove redundant license text
tty: serdev: Remove redundant license text
tty: hvc: Remove redundant license text
tty: serial: Remove redundant license text
tty: add SPDX identifiers to all remaining files in drivers/tty/
tty: serial: jsm: remove redundant pointer ts
tty: serial: jsm: add space before the open parenthesis '('
tty: serial: jsm: fix coding style
tty: serial: jsm: delete space between function name and '('
tty: serial: jsm: add blank line after declarations
tty: serial: jsm: change the type of local variable
tty: serial: imx: remove dead code imx_dma_rxint
tty: serial: imx: disable ageing timer interrupt if dma in use
serial: 8250: fix potential deadlock in rs485-mode
serial: m32r_sio: Drop redundant .data assignment
...
The 8250_fintek.c is support the Fintek F81866/F81216 with dynamic clock.
But It'll generate "division by zero" exception and crash in
fintek_8250_set_termios() with baud rate 0 on baudrate_table[i] % baud.
It can be tested with following C code:
...
struct termios options;
tcgetattr(fd, &options);
...
options.c_cflag = CS8 | CREAD; /* baud rate 0 */
tcsetattr(fd, TCSANOW, &options);
tcflush(fd, TCIOFLUSH);
Fixes: 195638b6d4 ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81866")
Reported-by: Lukas Redlinger <rel+kernel@agilox.net>
Cc: Lukas Redlinger <rel+kernel@agilox.net>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the datasheet, only the first port supports delay before
send and delay after send.
Reported-by: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardware does not support having the same RTS level during RX and TX
when RS485 mode is on (URA in Fintek terminology).
The manufacturer has also confirmed that the delays are not enabled if
the RS485 mode is not enabled.
Therefore we should return -EINVAL if the user wants to have the same
value for RTS_ON_SEND and RTS_AFTER_SEND.
Cc: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all tty files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/tty files files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Canceling hrtimer when holding uart spinlock can deadlock.
CPU0: syscall write
-> get uart port spinlock
-> write uart
-> start_tx_rs485
-> hrtimer_cancel
-> wait for hrtimer callback to finish
CPU1: hrtimer IRQ
-> run hrtimer
-> em485_handle_stop_tx
-> get uart port spinlock
CPU0 is waiting for the hrtimer callback to finish, but the hrtimer
callback running on CPU1 is waiting to get the uart port spinlock.
This deadlock can be avoided by not canceling the hrtimers in these paths.
Setting active_timer=NULL can be done without accessing hrtimer,
and that will effectively cancel operations that would otherwise have been
performed by the hrtimer callback.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver's ->rs485_config callback checks if SER_RS485_RTS_ON_SEND
and SER_RS485_RTS_AFTER_SEND have the same value. If they do, it means
the user has passed in invalid data with the TIOCSRS485 ioctl()
since RTS must have a different polarity when sending and when not
sending. In this case, rs485 mode is not enabled (the RS485_URA bit
is not set in the RS485 Enable Register) and this is supposed to be
signaled back to the user by clearing the SER_RS485_ENABLED bit in
struct serial_rs485 ... except a missing tilde character is preventing
that from happening.
Fixes: 28e3fb6c4d ("serial: Add support for Fintek F81216A LPC to 4 UART")
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Ed Blake <ed.blake@imgtec.com>
Cc: Matthias Brugger <mbrugger@suse.com>
Cc: Sean Young <sean@mess.org>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SuperIO will be configured at boot time by BIOS, but some BIOS
will not deactivate the SuperIO when the end of configuration. It'll
lead to mismatch for pdata->base_port in probe_setup_port(). So we'll
deactivate all SuperIO before activate special base_port in
fintek_8250_enter_key().
Tested on iBASE MI802.
Cc: stable@vger.kernel.org
Tested-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Reviewd-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The upper four bits of the XR17V35x fractional divisor register (DLD)
control general chip function (RS-485 direction pin polarity, multidrop
mode, XON/XOFF parity check, and fast IR mode). Don't allow these bits
to be clobbered when setting the baudrate.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently dw8250_set_termios sets the input clock to the nearest
achievable rate to baudx16. If necessary, the input clock is then
divided down to baudx16 using an integer divider within the UART
device, with the divisor calculated in the 8250 core driver.
However, the clock rate set by dw8250_set_termios and subsequently
divided down could be considerably different to the target baudx16
rate, resulting in incorrect operation. This patch fixes this by
iteratively searching for an input clock rate that is within +/-1.6%
of an integer multiple of the target baudx16 rate.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a define for the maximum baud rate divisor, to improve code
readability.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Cedar Fork PCH has similar HSU as has been used on Intel Denverton.
Add PCI ID to get it enumerated.
While here, remove DNV part form INTEL_MID_UART_DNV_FISR to show that is
used not only on Intel Denverton from now on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is fix the warning reported by smatch as following:
drivers/tty/serial/8250/8250_fintek.c:294 fintek_8250_goto_highspeed()
warn: inconsistent indenting
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
