Make use of the signal state registers to properly populate the signal lock
registers in the cx231xx driver.
This allows applications to know whether there is a signal present even in
devices which lack a tuner (since such apps typically won't call G_TUNER if
no tuner is present).
[mchehab@redhat.com: Fix CodingStyle: don't use {} for one-line if's]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On platforms that have CONFIG_HZ set to 100, the power ramp time effectively
ends up being 10ms. However, on those that have a higher CONFIG_HZ, the time
ends up *actually* being 5ms, which doesn't allow enough time for the hardware
to be fully powered up before attempting to address it via i2c.
Change the constant to 10ms, which is long enough for the hardware to power
up, and won't really be anymore time than it was previously on platforms
with CONFIG_HZ being 100.
Credit goes to Mauro Carvalho Chehab and Gerd Hoffmann who previously
investigated this issue.
Tested with the Hauppauge USBLive 2, with which the problem was readily
reproducible after setting CONFIG_HZ to 1000.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch addresses the regression introduced in the cx231xx
driver which stopped the Hauppauge USBLive2 from working.
Confirmed working by both myself and the user who reported the issue
on the KernelLabs blog (Robert DeLuca).
At some point during refactoring of the cx231xx driver, the USBLive 2 device
became broken. This patch results in the device working again.
Thanks to Robert DeLuca for sponsoring this work.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Robert DeLuca <robertdeluca@me.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The search for matching extension units fails to take account of the
current chain. In the case where you have two distinct video chains,
both containing an XU with the same GUID but different unit ids, you
will be unable to perform a mapping on the second chain because entity
on the first chain will always be found first
Fix this by only searching the current chain when performing a control
mapping. This is analogous to the search used by uvc_find_control(),
and is the correct behaviour.
Signed-off-by: Stephan Lachowsky <stephan.lachowsky@maxim-ic.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver reads PCI subsystem IDs from the PCI configuration registers while
they are already stored by the PCI subsystem in the 'subsystem_{vendor|device}'
fields of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both ngene and ddbrige calls dvb_attach once for drxk_attach.
The logic used there, and by tda18271c2dd driver is different
from similar logic on other frontends.
The right fix is to change them to use the same logic, but,
while we don't do that, we need to patch em28xx-dvb in order
to do cope with ngene/ddbridge magic.
While here, document why drxk_t_release should do nothing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch adds a new control that makes it possible to set the
luma notch filter type to finetune picture quality.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch implements support for a sharpness control, using the luma
peaking filter feature of cx2388x.
[mchehab@redhat.com: use cx_andor instead of cx_write]
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add driver for TV Mixer on Samsung platforms from S5P family.
Mixer is responsible for merging images from three layers and
passing result to the output.
Drivers are using:
- v4l2 framework
- videobuf2
- runtime PM
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add drivers for Standard Definition output (SDO) on Samsung platforms
from S5P family. The driver provides control over streaming analog TV
via Composite connector.
Driver is using:
- v4l2 framework
- runtime PM
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx88 driver would force core->input to always be zero when doing the
the request_acquire(). While it wasn't actually changing the input register
in the hardware, the driver makes decision based on the current input. In
particular, it decides whether to do things like enabling the comb filter
when on a composite input but disabling it on s-video. So for example, on
the HVR-1300, using the s-video input with the MPEG encoder would end up with
the video decoder core configured as though the input type were composite.
In short, the driver state did not match the hardware state.
This patch does two things:
1. It forces the input to zero only if actually switching to DVB mode. This
prevents the input from changing when the blackbird driver opens the device.
2. Keep track of what the input was set to when switching to DVB, and reset
it back when done. This eliminates a condition where for example the user
had the analog side of the board set to capture on the s-video input, then
he used DVB for a bit, then the analog input would unexpectedly be set to
the tuner input.
This work was sponsored by Anevia S.A.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Florent Audebert <florent.audebert@anevia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Multi Format Codec 5.1 is a hardware video coding acceleration
module found in the S5PV210 and Exynos4 Samsung SoCs. It is
capable of handling a range of video codecs and this driver
provides a V4L2 interface for video decoding and encoding.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Jeongtae Park <jtp.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Clear the cx231xx_devused variable and free dev in the error handling code,
as done in the error handling code nearby.
The semantic match that finds this problem is as follows:
// <smpl>
@r@
identifier x;
@@
kfree(x)
@@
identifier r.x;
expression E1!=0,E2,E3,E4;
statement S;
@@
(
if (<+...x...+>) S
|
if (...) { ... when != kfree(x)
when != if (...) { ... kfree(x); ... }
when != x = E3
* return E1;
}
... when != x = E2
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Free the recently allocated qcam in each case.
The semantic match that finds this problem is as follows:
// <smpl>
@r@
identifier x;
@@
kfree(x)
@@
identifier r.x;
expression E1!=0,E2,E3,E4;
statement S;
@@
(
if (<+...x...+>) S
|
if (...) { ... when != kfree(x)
when != if (...) { ... kfree(x); ... }
when != x = E3
* return E1;
}
... when != x = E2
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch, based on code by Mirek Slugen, implements support for the
Leadtek WinFast PxDVR3200 H card with XC4000 tuner (107d:6f39).
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure that the 'static' keywork is at the beginning of declaration
for drivers/media/video/omap/omap_vout.c
This gets rid of warnings like
when building with -Wold-style-declaration (and/or -Wextra which also
enables it).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Delete a couple of leftover fields whose time has passed.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Marvell camera core can support all three videobuf2 buffer modes, which
is slick, but it also requires that all three modes be built and present,
even though only one is likely to be used. This patch allows the supported
modes to be selected at configuration time, reducing the footprint of the
driver. Prior to this patch, the MMP camera driver looked like this:
mmp_camera 19092 0
videobuf2_core 15542 1 mmp_camera
videobuf2_dma_sg 3173 1 mmp_camera
videobuf2_dma_contig 2188 1 mmp_camera
videobuf2_vmalloc 1718 1 mmp_camera
videobuf2_memops 2100 3 videobuf2_dma_sg,videobuf2_dma_contig,videobuf2_vmalloc
Afterward, instead, with scatter/gather only configured:
mmp_camera 16021 0
videobuf2_core 15542 1 mmp_camera
videobuf2_dma_sg 3173 1 mmp_camera
videobuf2_memops 2100 1 videobuf2_dma_sg
The total goes from 43,813 bytes to 36,836.
The emphasis has been on simplicity and minimal #ifdef use rather than on
squeezing out every possible byte of code. For configuration, the driver
simply looks at which videobuf2 modes have been configured in and supports
them all; it's simplistic but should be good enough.
The cafe driver is set to support vmalloc and dma-contig; mmp supports only
dma-sg, since that's the only mode that really makes sense to use.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If registration does not work, we don't want to leave the sensor powered on.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Somewhere along the way the code stopped actually paying any attention to
them, and I doubt anybody has ever made use of them.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This code shows signs of having been mucked with over the last five years
or so; things were kind of mixed up. This patch reorders functions into a
more rational organization which, with luck, will facilitate making the
buffer modes selectable at configuration time. Code movement only: no
functional changes here.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This structure got passed over in the videobuf2 conversion; it has no
reason to exist now.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on the work of John Newbigin, Davor Emard and others who contributed
on the mailing lists.
The previous 'support' for this card was a partial merge of John's changes
that, as far as I can tell, never actually got the thing working (no DVB-T,
analog tuner not initialised).
Initialise the analog tuner properly and hook up the DVB tuner and demodulator.
DVB-T and analog now work (though I can't tune every DVB channel, but I think
there's an issue with the aerial and signal boosters here that is causing
me problems).
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use a name convention for the firmware file that matches on the
current firmware namespacing. Also, add it to the firmware
download script.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On em28xx, tda18271C2 is accessible when the i2c port
is not touched. Touching on it breaks the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All I2C logs we got for em28xx does that. With Terratec H5, at
400MHz speed, it seems that this is required, to avoid having
troubles at the I2C bus.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The microcode firmware provided on Terratec H5 seems to be
different. Add a parameter to allow specifying a different
firmware per-device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the codec controls to the v4l2 control framework.
[mchehab@redhat.com: Fix merge conflicts and removed some hunks that were
adding blank lines without a good reason]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the driver for the adp1653 LED flash controller. This
controller supports a high power led in flash and torch modes and an
indicator light, sometimes also called privacy light.
The adp1653 is used on the Nokia N900.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Tuukka Toivonen <tuukkat76@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David Cohen <dacohen@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a control class and a set of controls to support LED and Xenon flash
devices. An example of such a device is the adp1653.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By default no control events are sent to the application that caused the
control value or flags change (i.e. the control(s) passed to VIDIOC_S_CTRL
or VIDIOC_S_EXT_CTRLS). But if a change in one control causes a change in
another control that was not part of the control(s) in VIDIOC_S_CTRL or
S_EXT_CTRLS, then the application should be notified.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new values were never copied to userspace due to this copy and paste
error. This was introduced during the rewrite of this part of the code in
commit 3219f8a362640b7e4b7e2187b1094c4e46d85aa0.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove unused pwc-ioctl.h (the copy in include/media is used everywhere)
Remove almost empty pwc-uncompress.h, move single define to pwc.h
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes the API for this:
1) v4l2 spec compliant
2) match that of the UVC Logitech QuickCam Sphere models
For now this operates in parellel to the sysfs interface for this, but the
intend is to deprecate the sysfs interface and remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also remove all the converting from native range to 0-65535 and back
that was going on. This is no longer needed now that we no longer support
v4l1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow multiple opens of the /dev/video node so that control panel apps
can be open to-gether with streaming apps.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Doing a bunch of initialization every time /dev/video is opened, and thus
for example when the udev rules probe for capabilities makes no sense,
do it at driver load, resp. stream start instead.
This is a preparation patch for allowing multiple opens of the /dev/video
node.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
as vcinterface must be set before calling pwc_camera_power()
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
