PCI_MSIX_FLAGS_MASKALL is set in the MSI-X control register at MSI-X
interrupt setup time. It's cleared on success, but the error handling path
only clears the PCI_MSIX_FLAGS_ENABLE bit.
That's incorrect as the reset state of the PCI_MSIX_FLAGS_MASKALL bit is
zero. That can be observed via lspci:
Capabilities: [b0] MSI-X: Enable- Count=67 Masked+
Clear the bit in the error path to restore the reset state.
Fixes: 438553958b ("PCI/MSI: Enable and mask MSI-X early")
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Stefan Roese <sr@denx.de>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87tufevoqx.ffs@tglx
Masking all unused MSI-X entries is done to ensure that a crash kernel
starts from a clean slate, which correponds to the reset state of the
device as defined in the PCI-E specificion 3.0 and later:
Vector Control for MSI-X Table Entries
--------------------------------------
"00: Mask bit: When this bit is set, the function is prohibited from
sending a message using this MSI-X Table entry.
...
This bit’s state after reset is 1 (entry is masked)."
A Marvell NVME device fails to deliver MSI interrupts after trying to
enable MSI-X interrupts due to that masking. It seems to take the MSI-X
mask bits into account even when MSI-X is disabled.
While not specification compliant, this can be cured by moving the masking
into the success path, so that the MSI-X table entries stay in device reset
state when the MSI-X setup fails.
[ tglx: Move it into the success path, add comment and amend changelog ]
Fixes: aa8092c1d1 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211210161025.3287927-1-sr@denx.de
-----BEGIN PGP SIGNATURE-----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=BWkT
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Revert emulation of Marvell Armada A3720 expansion ROM because it
doesn't work as expected (Marek Behún)
- Assert PERST# in Apple M1 driver to fix initialization when booting
from bootloaders using PCIe, such as U-Boot (Marc Zyngier)
- Describe PERST# as active low in Apple T8103 DT and update driver to
match (Marc Zyngier)
* tag 'pci-v5.16-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: apple: Fix PERST# polarity
arm64: dts: apple: t8103: Mark PCIe PERST# polarity active low in DT
PCI: apple: Follow the PCIe specifications when resetting the port
Revert "PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated bridge"
Daniel Borkmann says:
====================
bpf 2021-12-08
We've added 12 non-merge commits during the last 22 day(s) which contain
a total of 29 files changed, 659 insertions(+), 80 deletions(-).
The main changes are:
1) Fix an off-by-two error in packet range markings and also add a batch of
new tests for coverage of these corner cases, from Maxim Mikityanskiy.
2) Fix a compilation issue on MIPS JIT for R10000 CPUs, from Johan Almbladh.
3) Fix two functional regressions and a build warning related to BTF kfunc
for modules, from Kumar Kartikeya Dwivedi.
4) Fix outdated code and docs regarding BPF's migrate_disable() use on non-
PREEMPT_RT kernels, from Sebastian Andrzej Siewior.
5) Add missing includes in order to be able to detangle cgroup vs bpf header
dependencies, from Jakub Kicinski.
6) Fix regression in BPF sockmap tests caused by missing detachment of progs
from sockets when they are removed from the map, from John Fastabend.
7) Fix a missing "no previous prototype" warning in x86 JIT caused by BPF
dispatcher, from Björn Töpel.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Add selftests to cover packet access corner cases
bpf: Fix the off-by-two error in range markings
treewide: Add missing includes masked by cgroup -> bpf dependency
tools/resolve_btfids: Skip unresolved symbol warning for empty BTF sets
bpf: Fix bpf_check_mod_kfunc_call for built-in modules
bpf: Make CONFIG_DEBUG_INFO_BTF depend upon CONFIG_BPF_SYSCALL
mips, bpf: Fix reference to non-existing Kconfig symbol
bpf: Make sure bpf_disable_instrumentation() is safe vs preemption.
Documentation/locking/locktypes: Update migrate_disable() bits.
bpf, sockmap: Re-evaluate proto ops when psock is removed from sockmap
bpf, sockmap: Attach map progs to psock early for feature probes
bpf, x86: Fix "no previous prototype" warning
====================
Link: https://lore.kernel.org/r/20211208155125.11826-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that PERST# is properly defined as active-low in the device tree, fix
the driver to correctly drive the line independently of the implied
polarity.
Suggested-by: Pali Rohár <pali@kernel.org>
Fixes: 1e33888fbe ("PCI: apple: Add initial hardware bring-up")
Link: https://lore.kernel.org/r/20211123180636.80558-4-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
While the Apple PCIe driver works correctly when directly booted from the
firmware, it fails to initialise when the kernel is booted from a
bootloader using PCIe such as u-boot.
That's because we're missing a proper reset of the port (we only clear the
reset, but never assert it).
The PCIe spec requirements are two-fold:
- PERST# must be asserted before setting up the clocks and stay asserted
for at least 100us (Tperst-clk)
- Once PERST# is deasserted, the OS must wait for at least 100ms "from
the end of a Conventional Reset" before we can start talking to the
devices
Implementing this results in a booting system.
[bhelgaas: #PERST -> PERST#, update spec references to current]
Fixes: 1e33888fbe ("PCI: apple: Add initial hardware bring-up")
Link: https://lore.kernel.org/r/20211123180636.80558-2-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Pali Rohár <pali@kernel.org>
Cc: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
cgroup.h (therefore swap.h, therefore half of the universe)
includes bpf.h which in turn includes module.h and slab.h.
Since we're about to get rid of that dependency we need
to clean things up.
v2: drop the cpu.h include from cacheinfo.h, it's not necessary
and it makes riscv sensitive to ordering of include files.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Acked-by: SeongJae Park <sj@kernel.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/all/20211120035253.72074-1-kuba@kernel.org/ # v1
Link: https://lore.kernel.org/all/20211120165528.197359-1-kuba@kernel.org/ # cacheinfo discussion
Link: https://lore.kernel.org/bpf/20211202203400.1208663-1-kuba@kernel.org
This reverts commit 239edf686c.
239edf686c ("PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated
bridge") added support for the Type 1 Expansion ROM BAR at config offset
0x38, based on the register being listed in the Marvell Armada A3720 spec.
But the spec doesn't document it at all for RC mode, and there is no ROM in
the SOC, so remove this emulation for now.
The PCI bridge which represents aardvark's PCIe Root Port has an Expansion
ROM Base Address register at offset 0x30, but its meaning is different than
PCI's Expansion ROM BAR register, although the layout is the same. (This
is why we thought it does the same thing.)
First: there is no ROM (or part of BootROM) in the A3720 SOC dedicated for
PCIe Root Port (or controller in RC mode) containing executable code that
would initialize the Root Port, suitable for execution in bootloader (this
is how Expansion ROM BAR is used on x86).
Second: in A3720 spec the register (address 0xD0070030) is not documented
at all for Root Complex mode, but similar to other BAR registers, it has an
"entangled partner" in register 0xD0075920, which does address translation
for the BAR in 0xD0070030:
- the BAR register sets the address from the view of PCIe bus
- the translation register sets the address from the view of the CPU
The other BAR registers also have this entangled partner, and they can be
used to:
- in RC mode: address-checking on the receive side of the RC (they can
define address ranges for memory accesses from remote Endpoints to the
RC)
- in Endpoint mode: allow the remote CPU to access memory on A3720
The Expansion ROM BAR has only the Endpoint part documented, but from the
similarities we think that it can also be used in RC mode in that way.
So either Expansion ROM BAR has different meaning (if the hypothesis above
is true), or we don't know it's meaning (since it is not documented for RC
mode).
Remove the register from the emulated bridge accessing functions.
[bhelgaas: summarize reason for removal (first paragraph)]
Fixes: 239edf686c ("PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated bridge")
Link: https://lore.kernel.org/r/20211125160148.26029-3-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
- Core code:
A regression fix for the Open Firmware interrupt mapping code where a
interrupt controller property in a node caused a map property in the
same node to be ignored.
- Interrupt chip drivers:
- Workaround a limitation in SiFive PLIC interrupt chip which silently
ignores an EOI when the interrupt line is masked.
- Provide the missing mask/unmask implementation for the CSKY MP
interrupt controller.
- PCI/MSI:
- Prevent a use after free when PCI/MSI interrupts are released by
destroying the sysfs entries before freeing the memory which is
accessed in the sysfs show() function.
- Implement a mask quirk for the Nvidia ION AHCI chip which does not
advertise masking capability despite implementing it. Even worse the
chip comes out of reset with all MSI entries masked, which due to the
missing masking capability never get unmasked.
- Move the check which prevents accessing the MSI[X] masking for XEN
back into the low level accessors. The recent consolidation missed
that these accessors can be invoked from places which do not have
that check which broke XEN. Move them back to he original place
instead of sprinkling tons of these checks all over the code.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAmGRDCsTHHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoTL5D/4n7CUudohHPckr0Rl3LbnSUfyY9g3H
irTKur71AT392YerJtQp+WBp3AKYMDD8wPTgydfpWe95ouIjx5jhb/co7uSifG6k
ZssXYS10bkvjqyS8E2s5FnA5xbnagunK/R981qju14Ec39xqx1JzlUnO/Pra0Kcr
5rBV7br9jJMBleBI4OFuS9fS8dVL1MH/yushkuDNfIKEnaElnaxaYUk/ZdzkMMAW
lt1B+dPhK24t1hXQvZKp/iVQUGrJWdzzy9aDiUYPv1IZP+V5nbLMgmFvEv8jNdNa
6kkfp0l30nXM9rgvcp2KkasVUPVhurVEwitzz9+tT6LRA+/kSwi2yx8/FwCVUcL6
xD0AgKQgxOj/WwGJTZswvPu3afsLuw3rGmx5uH1IV40P9mPX0AiHWgvoaInHjzlJ
QKFQ7mJEuUcC6cJ36RGqX9njhKvPIcUENGCTjGSffcXsWltPrOCg2mQFcsDa9fSH
qPfXDVv4YINI+0MAlOULh6TLWQ07xy37HiskJu/AgILOfipoDi8pXdqNJRfvxB1S
D3O8vB+SH3lPj69w4dtj7539SdNZn8CCyN3RbNlstl2vHV5Bus3cVk0CcOhG8qNW
KwK/tSH8O0ZYHAsUu8OqBipXy6qOPi/10MJQn3NOpvvOmS4oDd+82bq+jp5qJpsG
42WNuzEoBdaUiA==
=LBQL
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes for the interrupt subsystem
Core code:
- A regression fix for the Open Firmware interrupt mapping code where
a interrupt controller property in a node caused a map property in
the same node to be ignored.
Interrupt chip drivers:
- Workaround a limitation in SiFive PLIC interrupt chip which
silently ignores an EOI when the interrupt line is masked.
- Provide the missing mask/unmask implementation for the CSKY MP
interrupt controller.
PCI/MSI:
- Prevent a use after free when PCI/MSI interrupts are released by
destroying the sysfs entries before freeing the memory which is
accessed in the sysfs show() function.
- Implement a mask quirk for the Nvidia ION AHCI chip which does not
advertise masking capability despite implementing it. Even worse
the chip comes out of reset with all MSI entries masked, which due
to the missing masking capability never get unmasked.
- Move the check which prevents accessing the MSI[X] masking for XEN
back into the low level accessors. The recent consolidation missed
that these accessors can be invoked from places which do not have
that check which broke XEN. Move them back to he original place
instead of sprinkling tons of these checks all over the code"
* tag 'irq-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
of/irq: Don't ignore interrupt-controller when interrupt-map failed
irqchip/sifive-plic: Fixup EOI failed when masked
irqchip/csky-mpintc: Fixup mask/unmask implementation
PCI/MSI: Destroy sysfs before freeing entries
PCI: Add MSI masking quirk for Nvidia ION AHCI
PCI/MSI: Deal with devices lying about their MSI mask capability
PCI/MSI: Move non-mask check back into low level accessors
- Add PCI automatic error recovery.
- Fix tape driver timer initialization broken during timers api cleanup.
- Fix bogus CPU measurement counters values on CPUs offlining.
- Check the validity of subchanel before reading other fields in
the schib in cio code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAmGPwDMACgkQjYWKoQLX
FBgCoQf/VBel0vDex9NNVo59OmGTNh9NPPT2cUU8vYEmwHfaBeInZVEx5WOxXijl
8MIbEgi6Wt3EwnIghjouC50nk8jCiNOJ8Z/wG+01zZpVpLk2GvKGjxoYxKg+5E6T
sOSr7TMeKOtOp23xKAXGVIzzkrDTSyr3qruTKg/m6TFhQ0XSm/ld2k6tR5AARbuB
UtsxBOtPWyHm1xPyuhjr+c6riK2vGQwJwYya4vGtIW8ix9uZoPabdqqzWsD3meBc
B6fe96YQGxA8Tt80FtyJ6pHEhNDr8CE656aJZNJCnd7q1RmLWC1R/aUme+9wqQtO
i9YmMvc+uzgQonpo+YgWqu9fIQqcXA==
=OjW1
-----END PGP SIGNATURE-----
Merge tag 's390-5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Vasily Gorbik:
- Add PCI automatic error recovery.
- Fix tape driver timer initialization broken during timers api
cleanup.
- Fix bogus CPU measurement counters values on CPUs offlining.
- Check the validity of subchanel before reading other fields in the
schib in cio code.
* tag 's390-5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cio: check the subchannel validity for dev_busid
s390/cpumf: cpum_cf PMU displays invalid value after hotplug remove
s390/tape: fix timer initialization in tape_std_assign()
s390/pci: implement minimal PCI error recovery
PCI: Export pci_dev_lock()
s390/pci: implement reset_slot for hotplug slot
s390/pci: refresh function handle in iomap
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmGNcPYUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vxTvQ//Wl8O7D+ckdw/4xMVi2N2uc6vCbB6
or5wmW1jfE6H7YvXbUrSMEBFoRfaz9nhuT3w9i60hzYmc9uqbsMCONBHLFAaILCP
By/qkNgMFuskZGHTziqsf2Qfza04KQDv4quUl8SvlUfQeOtzUXe0vtXCrFmMTDGs
QQ/bbVbI6WazTwzC11NALU3Kc8AZQXQMkd5Nt4fBfuZwFhBfnEckJgF3PmSZ7PpO
N/29wJDsdkHSBNqTO1eeqdVIN8GQ6aycUYEQp3gvDCvwQ3CXtPP6SScTnqibbzjO
3wuBk+FFH8Zdq8e7CEYoj0mL2RMKhLrY1MLV8IGI1YiPy8pH1EujOiDG0uNk7YSg
Zqo3NMq9L2IR28odTMc8W8oknz6CTO+rhoW22CbyImtrPT5RnWsyj1xH+k2lMxt/
3viTV5lDzKr6V6c5xdhCP26eNzt06mlrduvQ5EvsfGu6whckyrgd6XOppExdWA/S
24N9GCJuZRCp5wgETq+Vxl48ZWLzkJ3IwoVrIhx4UTChvXPIgYrviGnEFp64ZCuc
FbrINeeddxWdXkkuJ44FhmSkv7Gcl87w0cofy9tnArxZza5v3wGATFp7G1z8WO+0
HWoBhdeGGQ3+ClJUo9ihO2r9hABUbveJqxgjQbCs8P/7bR0acCoeGJCoZVj7KUUe
a6GDw16Lfu87QuQ=
=0aFC
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Revert conversion to struct device.driver instead of struct
pci_dev.driver.
The device.driver is set earlier, and using it caused the PCI core to
call driver PM entry points before .probe() and after .remove(), when
the driver isn't prepared.
This caused NULL pointer dereferences in i2c_designware_pci and
probably other driver issues"
* tag 'pci-v5.16-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: Use to_pci_driver() instead of pci_dev->driver"
Revert "PCI: Remove struct pci_dev->driver"
This reverts commit 2a4d9408c9.
Robert reported a NULL pointer dereference caused by the PCI core
(local_pci_probe()) calling the i2c_designware_pci driver's
.runtime_resume() method before the .probe() method. i2c_dw_pci_resume()
depends on initialization done by i2c_dw_pci_probe().
Prior to 2a4d9408c9 ("PCI: Use to_pci_driver() instead of
pci_dev->driver"), pci_pm_runtime_resume() avoided calling the
.runtime_resume() method because pci_dev->driver had not been set yet.
2a4d9408c9 and b5f9c644eb ("PCI: Remove struct pci_dev->driver"),
removed pci_dev->driver, replacing it by device->driver, which *has* been
set by this time, so pci_pm_runtime_resume() called the .runtime_resume()
method when it previously had not.
Fixes: 2a4d9408c9 ("PCI: Use to_pci_driver() instead of pci_dev->driver")
Link: https://lore.kernel.org/linux-i2c/CAP145pgdrdiMAT7=-iB1DMgA7t_bMqTcJL4N0=6u8kNY3EU0dw@mail.gmail.com/
Reported-by: Robert Święcki <robert@swiecki.net>
Tested-by: Robert Święcki <robert@swiecki.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit b5f9c644eb.
Revert b5f9c644eb ("PCI: Remove struct pci_dev->driver"), which is needed
to revert 2a4d9408c9 ("PCI: Use to_pci_driver() instead of
pci_dev->driver").
2a4d9408c9 caused a NULL pointer dereference reported by Robert Święcki.
Details in the revert of that commit.
Fixes: 2a4d9408c9 ("PCI: Use to_pci_driver() instead of pci_dev->driver")
Link: https://lore.kernel.org/linux-i2c/CAP145pgdrdiMAT7=-iB1DMgA7t_bMqTcJL4N0=6u8kNY3EU0dw@mail.gmail.com/
Reported-by: Robert Święcki <robert@swiecki.net>
Tested-by: Robert Święcki <robert@swiecki.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
free_msi_irqs() frees the MSI entries before destroying the sysfs entries
which are exposing them. Nothing prevents a concurrent free while a sysfs
file is read and accesses the possibly freed entry.
Move the sysfs release ahead of freeing the entries.
Fixes: 1c51b50c29 ("PCI/MSI: Export MSI mode using attributes, not kobjects")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87sfw5305m.ffs@tglx
It appears that some devices are lying about their mask capability,
pretending that they don't have it, while they actually do.
The net result is that now that we don't enable MSIs on such
endpoint.
Add a new per-device flag to deal with this. Further patches will
make use of it, sadly.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20211104180130.3825416-2-maz@kernel.org
Cc: Bjorn Helgaas <helgaas@kernel.org>
The recent rework of PCI/MSI[X] masking moved the non-mask checks from the
low level accessors into the higher level mask/unmask functions.
This missed the fact that these accessors can be invoked from other places
as well. The missing checks break XEN-PV which sets pci_msi_ignore_mask and
also violates the virtual MSIX and the msi_attrib.maskbit protections.
Instead of sprinkling checks all over the place, lift them back into the
low level accessor functions. To avoid checking three different conditions
combine them into one property of msi_desc::msi_attrib.
[ josef: Fixed the missed conversion in the core code ]
Fixes: fcacdfbef5 ("PCI/MSI: Provide a new set of mask and unmask functions")
Reported-by: Josef Johansson <josef@oderland.se>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Josef Johansson <josef@oderland.se>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: stable@vger.kernel.org
BMIPS_GENERIC denotes support for the MIPS-based Broadcom STB platforms
which this driver can support.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
- Fix support for platforms that do not enumerate every ACPI0016 (CXL
Host Bridge) in the CHBS (ACPI Host Bridge Structure).
- Introduce a common pci_find_dvsec_capability() helper, clean up open
coded implementations in various drivers.
- Add 'cxl_test' for regression testing CXL subsystem ABIs. 'cxl_test'
is a module built from tools/testing/cxl/ that mocks up a CXL topology
to augment the nascent support for emulation of CXL devices in QEMU.
- Convert libnvdimm to use the uuid API.
- Complete the definition of CXL namespace labels in libnvdimm.
- Tunnel libnvdimm label operations from nd_ioctl() back to the CXL
mailbox driver. Enable 'ndctl {read,write}-labels' for CXL.
- Continue to sort and refactor functionality into distinct driver and
core-infrastructure buckets. For example, mailbox handling is now a
generic core capability consumed by the PCI and cxl_test drivers.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSbo+XnGs+rwLz9XGXfioYZHlFsZwUCYYRtyQAKCRDfioYZHlFs
Z7UsAP9DzUN6IWWnYk1R95YXYVxFriRtRsBjujAqTg49EMghawEAoHaA9lxO3Hho
l25TLYUOmB/zFTlUbe6YQptMJZ5YLwY=
=im9j
-----END PGP SIGNATURE-----
Merge tag 'cxl-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl updates from Dan Williams:
"More preparation and plumbing work in the CXL subsystem.
From an end user perspective the highlight here is lighting up the CXL
Persistent Memory related commands (label read / write) with the
generic ioctl() front-end in LIBNVDIMM.
Otherwise, the ability to instantiate new persistent and volatile
memory regions is still on track for v5.17.
Summary:
- Fix support for platforms that do not enumerate every ACPI0016 (CXL
Host Bridge) in the CHBS (ACPI Host Bridge Structure).
- Introduce a common pci_find_dvsec_capability() helper, clean up
open coded implementations in various drivers.
- Add 'cxl_test' for regression testing CXL subsystem ABIs.
'cxl_test' is a module built from tools/testing/cxl/ that mocks up
a CXL topology to augment the nascent support for emulation of CXL
devices in QEMU.
- Convert libnvdimm to use the uuid API.
- Complete the definition of CXL namespace labels in libnvdimm.
- Tunnel libnvdimm label operations from nd_ioctl() back to the CXL
mailbox driver. Enable 'ndctl {read,write}-labels' for CXL.
- Continue to sort and refactor functionality into distinct driver
and core-infrastructure buckets. For example, mailbox handling is
now a generic core capability consumed by the PCI and cxl_test
drivers"
* tag 'cxl-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl: (34 commits)
ocxl: Use pci core's DVSEC functionality
cxl/pci: Use pci core's DVSEC functionality
PCI: Add pci_find_dvsec_capability to find designated VSEC
cxl/pci: Split cxl_pci_setup_regs()
cxl/pci: Add @base to cxl_register_map
cxl/pci: Make more use of cxl_register_map
cxl/pci: Remove pci request/release regions
cxl/pci: Fix NULL vs ERR_PTR confusion
cxl/pci: Remove dev_dbg for unknown register blocks
cxl/pci: Convert register block identifiers to an enum
cxl/acpi: Do not fail cxl_acpi_probe() based on a missing CHBS
cxl/pci: Disambiguate cxl_pci further from cxl_mem
Documentation/cxl: Add bus internal docs
cxl/core: Split decoder setup into alloc + add
tools/testing/cxl: Introduce a mock memory device + driver
cxl/mbox: Move command definitions to common location
cxl/bus: Populate the target list at decoder create
tools/testing/cxl: Introduce a mocked-up CXL port hierarchy
cxl/pmem: Add support for multiple nvdimm-bridge objects
cxl/pmem: Translate NVDIMM label commands to CXL label commands
...
Commit e3a9b1212b ("PCI: Export pci_dev_trylock() and pci_dev_unlock()")
already exported pci_dev_trylock()/pci_dev_unlock() however in some
circumstances such as during error recovery it makes sense to block
waiting to get full access to the device so also export pci_dev_lock().
Link: https://lore.kernel.org/all/20210928181014.GA713179@bhelgaas/
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
This is done by adding a zpci_hot_reset_device() call which does a low
level reset of the PCI function without changing its higher level
function state. This way it can be used while the zPCI function is bound
to a driver and with DMA tables being controlled either through the
IOMMU or DMA APIs which is prohibited when using zpci_disable_device()
as that drop existing DMA translations.
As this reset, unlike a normal FLR, also calls zpci_clear_irq() we need
to implement arch_restore_msi_irqs() and make sure we re-enable IRQs for
the PCI function if they were previously disabled.
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----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=nsMh
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
- Use PCI_VENDOR_ID_AMCC macro instead of defining a custom macro in
pci-xgene.c (Pali Rohár)
* remotes/lorenzo/pci/xgene:
PCI: xgene: Use PCI_VENDOR_ID_AMCC macro
- Assign a number to each VMD controller to distinguish them in
/proc/interrupts (Chunguang Xu)
- Don't disable VMD MSI-X remapping if IOMMU remapping is enabled (Adrian
Huang)
- Add Kconfig dependency on !UML for allyesconfig build issue (Johannes
Berg)
* remotes/lorenzo/pci/vmd:
PCI: vmd: depend on !UML
PCI: vmd: Do not disable MSI-X remapping if interrupt remapping is enabled by IOMMU
PCI: vmd: Assign a number to each VMD controller
- Reorganize to separate out PHY logic (Mauro Carvalho Chehab)
- Add support for external PHY in addition to the internal PHY (Mauro
Carvalho Chehab)
- Use regmap so both kirin driver and PHY can access APB registers (Mauro
Carvalho Chehab)
- Add support for per-lane PERST# GPIOs on HiKey970 external PEX 8606 PCI
bridge (Mauro Carvalho Chehab)
- Add "hisilicon,kirin970-pcie" compatible string (Mauro Carvalho Chehab)
- Add MODULE_* macros (Mauro Carvalho Chehab)
- Allow building as a module (Mauro Carvalho Chehab)
- Add power_off support for Kirin 960 PHY (Mauro Carvalho Chehab)
- Disable clkreq during poweroff sequence (Mauro Carvalho Chehab)
- De-init the dwc driver during remove (Mauro Carvalho Chehab)
- Allow removal of kirin driver (Mauro Carvalho Chehab)
* pci/host/kirin:
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: kirin: Use regmap for APB registers
PCI: kirin: Add support for a PHY layer
PCI: kirin: Reorganize the PHY logic inside the driver
- Use sysfs_emit() in "show" functions instead of sprintf() to avoid buffer
overruns (Kunihiko Hayashi)
* remotes/lorenzo/pci/endpoint:
PCI: endpoint: Use sysfs_emit() in "show" functions
- Export dw_pcie_ep_reset_bar(), dw_pcie_link_up() so more drivers can be
modular (Luca Ceresoli)
- Allow dra7xx host and endpoint drivers to be modules (Luca Ceresoli)
- Enable dra7xx optional external clock if present (Luca Ceresoli)
- Clean up Kconfig dependencies for PCIE_DW_HOST- and PCIE_DW_EP-based
drivers (Andy Shevchenko)
- Remove visconti redundant dev_err() after platform_get_irq_byname()
failure (Krzysztof Wilczyński)
- Run dwc .host_init() method before registering MSI interrupt handler so
we have a chance to deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Serialize uniphier INTx masking/unmasking (Kunihiko Hayashi)
* pci/host/dwc:
PCI: uniphier: Serialize INTx masking/unmasking and fix the bit operation
PCI: dwc: Perform host_init() before registering msi
PCI: visconti: Remove surplus dev_err() when using platform_get_irq_byname()
PCI: dwc: Clean up Kconfig dependencies (PCIE_DW_EP)
PCI: dwc: Clean up Kconfig dependencies (PCIE_DW_HOST)
PCI: dra7xx: Get an optional clock
PCI: dra7xx: Remove unused include
PCI: dra7xx: Make it a kernel module
PCI: dwc: Export more symbols to allow modular drivers
- Make of_phandle_args_to_fwspec() generally available (Marc Zyngier)
- Allow matching of interrupt-maps local to interrupt controller or PCI
device (Marc Zyngier)
- Add Apple SoC (e.g., M1) PCIe host controller driver, which enables
access to USB type-A, Ethernet, Wi-Fi, Bluetooth devices; these require
additional drivers of their own (Alyssa Rosenzweig)
- Add apple INTx, per-port, and MSI interrupt support (Marc Zyngier)
- Configure apple Requester-ID-to-Stream-ID mapper for IOMMU (DART) support
(Marc Zyngier)
* pci/host/apple:
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits (Marek
Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits at
startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge" instead of
the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement this per
spec (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated bridge
PCI: aardvark: Fix support for PCI_BRIDGE_CTL_BUS_RESET on emulated bridge
PCI: aardvark: Set PCI Bridge Class Code to PCI Bridge
PCI: aardvark: Fix support for bus mastering and PCI_COMMAND on emulated bridge
PCI: aardvark: Read all 16-bits from PCIE_MSI_PAYLOAD_REG
PCI: aardvark: Fix return value of MSI domain .alloc() method
PCI: pci-bridge-emul: Fix emulation of W1C bits
PCI: aardvark: Fix reporting Data Link Layer Link Active
PCI: aardvark: Fix checking for link up via LTSSM state
PCI: aardvark: Fix link training
PCI: aardvark: Simplify initialization of rootcap on virtual bridge
PCI: aardvark: Implement re-issuing config requests on CRS response
PCI: aardvark: Deduplicate code in advk_pcie_rd_conf()
PCI: aardvark: Do not unmask unused interrupts
PCI: aardvark: Do not clear status bits of masked interrupts
PCI: aardvark: Fix configuring Reference clock
PCI: aardvark: Fix preserving PCI_EXP_RTCTL_CRSSVE flag on emulated bridge
PCI: aardvark: Don't spam about PIO Response Status
PCI: aardvark: Fix PCIe Max Payload Size setting
PCI: Add PCI_EXP_DEVCTL_PAYLOAD_* macros
- Tidy setup-irq.c comments (Pranay Sanghai)
- Fix misspellings (Krzysztof Wilczyński)
- Fix sprintf(), sscanf() format mismatches (Krzysztof Wilczyński)
- Tidy cpqphp code formatting (Krzysztof Wilczyński)
- Remove unused pci_pool wrappers, which have been replaced by dma_pool
(Cai Huoqing)
- Remove a redundant initialization in __pci_reset_function_locked() (Colin
Ian King)
- Use 'unsigned int' instead of 'unsigned' (Krzysztof Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof Wilczyński)
- Include generic <linux/> headers instead of <asm/> for cpqphp and vmd
(Krzysztof Wilczyński)
* pci/misc:
PCI: vmd: Drop redundant includes of <asm/device.h>, <asm/msi.h>
PCI: cpqphp: Use <linux/io.h> instead of <asm/io.h>
MAINTAINERS: Update PCI subsystem information
PCI: Prefer 'unsigned int' over bare 'unsigned'
PCI: Remove redundant 'rc' initialization
PCI: Remove unused pci_pool wrappers
PCI: cpqphp: Format if-statement code block correctly
PCI: Use unsigned to match sscanf("%x") in pci_dev_str_match_path()
PCI: hv: Remove unnecessary use of %hx
PCI: Correct misspelled and remove duplicated words
PCI: Tidy comments
- Add pci_read_vpd_any(), pci_write_vpd_any() to access VPD at arbitrary
offsets (Heiner Kallweit)
- Use VPD API to replace custom code in cxgb3 driver (Heiner Kallweit)
* pci/vpd:
cxgb3: Remove seeprom_write and use VPD API
cxgb3: Use VPD API in t3_seeprom_wp()
cxgb3: Remove t3_seeprom_read and use VPD API
PCI/VPD: Use pci_read_vpd_any() in pci_vpd_size()
PCI/VPD: Add pci_read/write_vpd_any()
- Avoid bus resets on Atheros QCA6174, since they hang (Ingmar Klein)
- Use store and forward mode on Pericom PI7C9X2G switches to avoid ACS
erratum with ACS P2P Request Redirect (Nathan Rossi)
* pci/virtualization:
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: Mark Atheros QCA6174 to avoid bus reset
- Check for CAP_SYS_ADMIN before validating sysfs user input, not after
(Krzysztof Wilczyński)
- Always return -EINVAL from sysfs "store" functions for invalid user input
instead of -EINVAL sometimes and -ERANGE others (Krzysztof Wilczyński)
- Use kstrtobool() directly instead of the strtobool() wrapper (Krzysztof
Wilczyński)
* pci/sysfs:
PCI: Use kstrtobool() directly, sans strtobool() wrapper
PCI/sysfs: Return -EINVAL consistently from "store" functions
PCI/sysfs: Check CAP_SYS_ADMIN before parsing user input
# Conflicts:
# drivers/pci/iov.c
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable, etc
(Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID (Kelvin
Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions (Kelvin
Cao)
- Add check of event support (Logan Gunthorpe)
* pci/switchtec:
PCI/switchtec: Add check of event support
PCI/switchtec: Replace ENOTSUPP with EOPNOTSUPP
PCI/switchtec: Update the way of getting management VEP instance ID
PCI/switchtec: Fix a MRPC error status handling issue
PCI/switchtec: Error out MRPC execution when MMIO reads fail
- Don't setup portdrv IRQs if there are no port drivers that use them, to
conserve vectors and avoid spurious events (Jan Kiszka)
* pci/portdrv:
PCI/portdrv: Do not setup up IRQs if there are no users
- Apply bus offset correctly in DMA address calculation, which used the
wrong sign before (Wang Lu)
* pci/p2pdma:
PCI/P2PDMA: Apply bus offset correctly in DMA address calculation
- Document sysfs "irq" attribute, which contains either the INTx IRQ (the
intended behavior) or the first MSI IRQ (historical mistake retained for
backwards compatibility) (Barry Song)
- Rework "irq" sysfs show function to explicitly fetch first MSI IRQ
instead of depending on core to put it in dev->irq, to enable future core
cleanup (Barry Song)
* pci/msi:
PCI/sysfs: Explicitly show first MSI IRQ for 'irq'
PCI: Document /sys/bus/pci/devices/.../irq
- Ignore Link Down/Up caused by error-induced Hot Reset so endpoint driver
can remain bound to device during error recovery (Lukas Wunner)
- Remove unused resume err_handler (Lukas Wunner)
- Remove unused pcie_port_bus_{,un}register() declarations (Lukas Wunner)
- Skip compiling err.c when CONFIG_PCIEAER not set (Lukas Wunner)
* pci/hotplug:
PCI/ERR: Reduce compile time for CONFIG_PCIEAER=n
PCI/portdrv: Remove unused pcie_port_bus_{,un}register() declarations
PCI/portdrv: Remove unused resume err_handler
PCI: pciehp: Ignore Link Down/Up caused by error-induced Hot Reset
PCI/portdrv: Rename pm_iter() to pcie_port_device_iter()
- Drop the struct pci_dev.driver pointer, which is redundant with the
struct device.driver pointer (Uwe Kleine-König)
* pci/driver:
PCI: Remove struct pci_dev->driver
PCI: Use to_pci_driver() instead of pci_dev->driver
x86/pci/probe_roms: Use to_pci_driver() instead of pci_dev->driver
perf/x86/intel/uncore: Use to_pci_driver() instead of pci_dev->driver
powerpc/eeh: Use to_pci_driver() instead of pci_dev->driver
usb: xhci: Use to_pci_driver() instead of pci_dev->driver
cxl: Use to_pci_driver() instead of pci_dev->driver
cxl: Factor out common dev->driver expressions
xen/pcifront: Use to_pci_driver() instead of pci_dev->driver
xen/pcifront: Drop pcifront_common_process() tests of pcidev, pdrv
nfp: use dev_driver_string() instead of pci_dev->driver->name
mlxsw: pci: Use dev_driver_string() instead of pci_dev->driver->name
net: marvell: prestera: use dev_driver_string() instead of pci_dev->driver->name
net: hns3: use dev_driver_string() instead of pci_dev->driver->name
crypto: hisilicon - use dev_driver_string() instead of pci_dev->driver->name
powerpc/eeh: Use dev_driver_string() instead of struct pci_dev->driver->name
ssb: Use dev_driver_string() instead of pci_dev->driver->name
bcma: simplify reference to driver name
crypto: qat - simplify adf_enable_aer()
scsi: message: fusion: Remove unused mpt_pci driver .probe() 'id' parameter
PCI/ERR: Factor out common dev->driver expressions
PCI: Drop pci_device_probe() test of !pci_dev->driver
PCI: Drop pci_device_remove() test of pci_dev->driver
PCI: Return NULL for to_pci_driver(NULL)
- Rename pcibios_add_device() to pcibios_device_add() since it's called
from pci_device_add() (Oliver O'Halloran)
- Don't try to enable AtomicOps on VFs, since they can only be enabled on
the PF (Selvin Xavier)
* pci/enumeration:
PCI: Do not enable AtomicOps on VFs
PCI: Rename pcibios_add_device() to pcibios_device_add()
The Pericom PI7C9X2G404/PI7C9X2G304/PI7C9X2G303 PCIe switches have an
erratum for ACS P2P Request Redirect behaviour when used in the cut-through
forwarding mode. The recommended work around for this issue is to use the
switch in store and forward mode. The erratum results in packets being
queued and not being delivered upstream, which can be observed as very poor
downstream device performance and/or dropped device-generated
data/interrupts.
Add a fixup so that when enabling or resuming the downstream port we check
if it has enabled ACS P2P Request Redirect, and if so, change the device
(via the upstream port) to use the store and forward operating mode.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=177471
Link: https://lore.kernel.org/r/20210910025823.196508-1-nathan@nathanrossi.com
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Apple PCIe controller doesn't directly feed the endpoint's Requester ID
to the IOMMU (DART), but instead maps RIDs onto Stream IDs (SIDs). The DART
and the PCIe controller must thus agree on the SIDs that are used for
translation (by using the 'iommu-map' property).
For this purpose, parse the 'iommu-map' property each time a device gets
added, and use the resulting translation to configure the PCIe RID-to-SID
mapper. Similarly, remove the translation if/when the device gets removed.
This is all driven from a bus notifier which gets registered at probe time.
Hopefully this is the only PCI controller driver in the whole system.
[bhelgaas: squash indentation from Zhaoyu Liu <zackary.liu.pro@gmail.com>:
https://lore.kernel.org/r/20211031135544.GA1616@pc]
Link: https://lore.kernel.org/r/20210929163847.2807812-10-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
The MSI doorbell on Apple HW can be any address in the low 4GB range.
However, the MSI write is matched by the PCIe block before hitting the
iommu. It must thus be excluded from the IOVA range that is assigned to any
PCIe device.
Link: https://lore.kernel.org/r/20210929163847.2807812-9-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
