e1000 uses the same metadata struct for Rx and Tx. But Tx and Rx have
different requirements.
For Rx, we only need to store a buffer and a DMA address.
Follow-up patch will remove skb for Rx, bringing rx_buffer_info down
to 16 bytes on x86_64.
[ buffer_info is 48 bytes ]
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we unmap the DMA range, then copy to new skb.
Change this so we can keep the mapping in case the data is copied.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Its the same in both handlers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
... and make it static.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change addresses several issues in the current ixgbe implementation of
busy poll sockets.
First was the fact that it was possible for frames to be delivered out of
order if they were held in GRO. This is addressed by flushing the GRO buffers
before releasing the q_vector back to the idle state.
The other issue was the fact that we were having to take a spinlock on
changing the state to and from idle. To resolve this I have replaced the
state value with an atomic and use atomic_cmpxchg to change the value from
idle, and a simple atomic set to restore it back to idle after we have
acquired it. This allows us to only use a locked operation on acquiring the
vector without a need for a locked operation to release it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change removes the Rx buffer allocation at the end of ixgbe_clean_rx_irq.
The reason for removing this is to avoid the extra latency introduced by the
MMIO write. This can amount to somewhere around an extra 100ns of latency and
one extra message worth of PCIe bus overhead.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resolve missing-field-initializers warnings by using
designated initialization.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves warnings produced by ixgbe in W=2 kernel
builds. There are missing-field-initializers warnings and shadow
warnings. None of these point to any deeper problem, so just
resolve them so any new warnings get analyzed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since BPF JIT depends on the availability of module_alloc() and
module_free() helpers (HAVE_BPF_JIT and MODULES), we better build
that code only in case we have BPF_JIT in our config enabled, just
like with other JIT code. Fixes builds for arm/marzen_defconfig
and sh/rsk7269_defconfig.
====================
kernel/built-in.o: In function `bpf_jit_binary_alloc':
/home/cwang/linux/kernel/bpf/core.c:144: undefined reference to `module_alloc'
kernel/built-in.o: In function `bpf_jit_binary_free':
/home/cwang/linux/kernel/bpf/core.c:164: undefined reference to `module_free'
make: *** [vmlinux] Error 1
====================
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: 738cbe72ad ("net: bpf: consolidate JIT binary allocator")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai says:
====================
cxgb4: Allow FW size upto 1MB, support for S25FL032P flash and misc. fixes
This patch series adds support to allow FW size upto 1MB, support for S25FL032P
flash. Fix t4_flash_erase_sectors to throw an error, when erase sector aren't in
the flash and also warning message when adapters have flashes less than 2Mb.
Adds device id of new adapter and removes device id of debug adapter.
The patches series is created against 'net-next' tree.
And includes patches on cxgb4 driver and cxgb4vf driver.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Spansion S25FL032P flash
Based on original work by Dimitris Michailidis
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following sparse warnings:
sparse: symbol 'tipc_update_nametbl' was not declared. Should it be static?
Also, the function is changed to return bool upon success, rather than a
potentially freed pointer.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free resources before being disconnected from phy and calling core driver is
wrong and should not happen. It avoids a delay of 4-5s caused by the timeout of
phy_disconnect().
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
nf-next pull request
The following patchset contains Netfilter/IPVS updates for your
net-next tree. Regarding nf_tables, most updates focus on consolidating
the NAT infrastructure and adding support for masquerading. More
specifically, they are:
1) use __u8 instead of u_int8_t in arptables header, from
Mike Frysinger.
2) Add support to match by skb->pkttype to the meta expression, from
Ana Rey.
3) Add support to match by cpu to the meta expression, also from
Ana Rey.
4) A smatch warning about IPSET_ATTR_MARKMASK validation, patch from
Vytas Dauksa.
5) Fix netnet and netportnet hash types the range support for IPv4,
from Sergey Popovich.
6) Fix missing-field-initializer warnings resolved, from Mark Rustad.
7) Dan Carperter reported possible integer overflows in ipset, from
Jozsef Kadlecsick.
8) Filter out accounting objects in nfacct by type, so you can
selectively reset quotas, from Alexey Perevalov.
9) Move specific NAT IPv4 functions to the core so x_tables and
nf_tables can share the same NAT IPv4 engine.
10) Use the new NAT IPv4 functions from nft_chain_nat_ipv4.
11) Move specific NAT IPv6 functions to the core so x_tables and
nf_tables can share the same NAT IPv4 engine.
12) Use the new NAT IPv6 functions from nft_chain_nat_ipv6.
13) Refactor code to add nft_delrule(), which can be reused in the
enhancement of the NFT_MSG_DELTABLE to remove a table and its
content, from Arturo Borrero.
14) Add a helper function to unregister chain hooks, from
Arturo Borrero.
15) A cleanup to rename to nft_delrule_by_chain for consistency with
the new nft_*() functions, also from Arturo.
16) Add support to match devgroup to the meta expression, from Ana Rey.
17) Reduce stack usage for IPVS socket option, from Julian Anastasov.
18) Remove unnecessary textsearch state initialization in xt_string,
from Bojan Prtvar.
19) Add several helper functions to nf_tables, more work to prepare
the enhancement of NFT_MSG_DELTABLE, again from Arturo Borrero.
20) Enhance NFT_MSG_DELTABLE to delete a table and its content, from
Arturo Borrero.
21) Support NAT flags in the nat expression to indicate the flavour,
eg. random fully, from Arturo.
22) Add missing audit code to ebtables when replacing tables, from
Nicolas Dichtel.
23) Generalize the IPv4 masquerading code to allow its re-use from
nf_tables, from Arturo.
24) Generalize the IPv6 masquerading code, also from Arturo.
25) Add the new masq expression to support IPv4/IPv6 masquerading
from nf_tables, also from Arturo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the more common pr_warn.
Other miscellanea:
o Coalesce formats
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the more common pr_warn.
Coalesce formats.
Realign arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert says:
====================
net: enable GRO for IPIP and SIT
This patch sets populates the IPIP and SIT offload structures with
gro_receive and gro_complete functions. This enables use of GRO
for these. Also, fixed a problem in IPv6 where we were not properly
initializing flush_id.
Peformance results are below. Note that these tests were done on bnx2x
which doesn't provide RX checksum offload of IPIP or SIT (i.e. does
not give CHEKCSUM_COMPLETE). Also, we don't get 4-tuple hash for RSS
only 2-tuple in this case so all the packets between two hosts are
winding up on the same queue. Net result is the interrupting CPU is
the bottleneck in GRO (checksumming every packet there).
Testing:
netperf TCP_STREAM between two hosts using bnx2x.
* Before fix
IPIP
1 connection
6.53% CPU utilization
6544.71 Mbps
20 connections
13.79% CPU utilization
9284.54 Mbps
SIT
1 connection
6.68% CPU utilization
5653.36 Mbps
20 connections
18.88% CPU utilization
9154.61 Mbps
* After fix
IPIP
1 connection
5.73% CPU utilization
9279.53 Mbps
20 connections
7.14% CPU utilization
7279.35 Mbps
SIT
1 connection
2.95% CPU utilization
9143.36 Mbps
20 connections
7.09% CPU utilization
6255.3 Mbps
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ipv6_gro_receive and ipv6_gro_complete to sit_offload to
support GRO.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add inet_gro_receive and inet_gro_complete to ipip_offload to
support GRO.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In TCP gro we check flush_id which is derived from the IP identifier.
In IPv4 gro path the flush_id is set with the expectation that every
matched packet increments IP identifier. In IPv6, the flush_id is
never set and thus is uinitialized. What's worse is that in IPv6
over IPv4 encapsulation, the IP identifier is taken from the outer
header which is currently not incremented on every packet for Linux
stack, so GRO in this case never matches packets (identifier is
not increasing).
This patch clears flush_id for every time for a matched packet in
IPv6 gro_receive. We need to do this each time to overwrite the
setting that would be done in IPv4 gro_receive per the outer
header in IPv6 over Ipv4 encapsulation.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Typo fixes submiting/submitting
o Coalesce formats
o Realign arguments
o Add missing terminating '\n' to formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv4/udp_offload.c:339:5: warning: symbol 'udp4_gro_complete' was
not declared. Should it be static?
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Fixes: 57c67ff4bd ("udp: additional GRO support")
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/core/net_namespace.c:227:18: warning: incorrect type in argument 1
(different address spaces)
net/core/net_namespace.c:227:18: expected void const *<noident>
net/core/net_namespace.c:227:18: got struct net_generic [noderef]
<asn:4>*gen
We can use rcu_access_pointer() here as read-side access to the pointer
was removed at least one grace period ago.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/udp_offload.c:159:5: warning: symbol 'udp6_gro_complete' was
not declared. Should it be static?
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 57c67ff4bd ("udp: additional GRO support")
Cc: Tom Herbert <therbert@google.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove one sparse warning :
net/ipv4/ip_sockglue.c:328:22: warning: incorrect type in assignment (different address spaces)
net/ipv4/ip_sockglue.c:328:22: expected struct ip_ra_chain [noderef] <asn:4>*next
net/ipv4/ip_sockglue.c:328:22: got struct ip_ra_chain *[assigned] ra
And replace one rcu_assign_ptr() by RCU_INIT_POINTER() where applicable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not used anywhere, so just remove these.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of looping in the code let's use kernel extension to dump small
buffers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace mdelay with usleep_range to avoid busy loop.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few packets have timestamping enabled. Exit sock_tx_timestamp quickly
in this common case.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
not used anymore since ddecf0f
(net_sched: sfq: add optional RED on top of SFQ).
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the normal transmit completion path from dev_kfree_skb_any()
to dev_consume_skb_any() to help keep dropped packet profiling
meaningful.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov says:
====================
bonding: get rid of bond->lock
This patch-set removes the last users of bond->lock and converts the places
that needed it for sync to use curr_slave_lock or RCU as appropriate.
I've run this with lockdep and have stress-tested it via loading/unloading
and enslaving/releasing in parallel while outputting bond's proc, I didn't
see any issues. Please pay special attention to the procfs change, I've
done about an hour of stress-testing on it and have checked that the event
that causes the bonding to delete its proc entry (NETDEV_UNREGISTER) is
called before ndo_uninit() and the freeing of the dev so any readers will
sync with that. Also ran sparse checks and there were no splats.
v2: Add patch 0001/cxgb4 bond->lock removal, RTNL should be held in the
notifier call, the other patches are the same. Also tested with
allmodconfig to make sure there're no more users of bond->lock.
Changes from the RFC:
use RCU in procfs instead of RTNL since RTNL might lead to a deadlock with
unloading and also is much slower. The bond destruction syncs with proc
via the proc locks. There's one new patch that converts primary_slave to
use RCU as it was necessary to fix a longstanding bugs in sysfs and
procfs and to make it easy to migrate bond's procfs to RCU. And of course
rebased on top of net-next current.
This is the first patch-set in a series that should simplify the bond's
locking requirements and will make it easier to define the locking
conditions necessary for the various paths. The goal is to rely on RTNL
and rcu alone, an extra lock would be needed in a few special cases that
would be documented very well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of bond->lock in bond_main.c was completely unnecessary as it
didn't help to sync with anything, most of the spots already had RTNL.
Since there're no more users of bond->lock, remove it.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're safe to remove the bond->lock use from the arp targets because
arp_rcv_probe no longer acquires bond->lock, only rcu_read_lock.
Also setting the primary slave is safe because noone uses the bond->lock
as a syncing mechanism for that anymore.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use RCU to protect against slave release, the proc show function will sync
with the bond destruction by the proc locks and the fact that the bond is
released after NETDEV_UNREGISTER which causes the bonding to remove the
proc entry.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is necessary mainly for two bonding call sites: procfs and
sysfs as it was dereferenced without any real protection.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can remove the lock/unlock as it's no longer necessary since
RTNL should be held while calling bond_alb_set_mac_address().
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 3ad mode the only syncing needed by bond->lock is for the wq
and the recv handler, so change them to use curr_slave_lock.
There're no locking dependencies here as 3ad doesn't use
curr_slave_lock at all.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTNL should be already held in the notifier call so the slave list can
be traversed without a problem, remove the unnecessary bond->lock.
CC: Hariprasad S <hariprasad@chelsio.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables EMAC Rockchip support on radxa rock boards.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for EMAC Rockchip driver on RK3188 SoCs.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the necessary binding documentation for the EMAC Rockchip platform
driver found in RK3066 and RK3188 SoCs.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines a platform glue layer for Rockchip SoCs which
support arc-emac driver. It ensures that regulator for the rmii is on
before trying to connect to the ethernet controller. It applies right
speed and mode changes to the grf when ethernet settings change.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
