Value must be a power of 2 due to HW limitation.
Driver supports only 'equal' mode in ethtool and can't be set by using weights.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several problems fixed in this patch :
1) Target of the conditional jump in case a divide by 0 is performed
by a bpf is wrong.
2) Must 'generate' the full function prologue/epilogue at pass=0,
or else we can stop too early in pass=1 if the proglen doesnt change.
(if the increase of prologue/epilogue equals decrease of all
instructions length because some jumps are converted to near jumps)
3) Change the wrong length detection at the end of code generation to
issue a more explicit message, no need for a full stack trace.
Reported-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deauth is requested while an auth or assoc
work item is in progress, we currently delete it
without regard for any state it might need to
clean up. Fix it by cleaning up for those items.
In the case Pontus found, the problem manifested
itself as such:
authenticate with 00:23:69:aa:dd:7b (try 1)
authenticated
failed to insert Dummy STA entry for the AP (error -17)
deauthenticating from 00:23:69:aa:dd:7b by local choice (reason=2)
It could also happen differently if the driver
uses the tx_sync callback.
We can't just call the ->done() method of the work
items because that will lock up due to the locking
in cfg80211. This fix isn't very clean, but that
seems acceptable since I have patches pending to
remove this code completely.
Cc: stable@vger.kernel.org
Reported-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Tested-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use local->tx_headroom instad of local->hw.extra_tx_headroom.
local->tx_headroom is the max of hw.extra_tx_headroom required by the
driver and the headroom required by mac80211 for status reporting. On
drivers where hw.extra_tx_headroom is smaller than what mac80211
requires (e.g. ath5k), we would not reserve sufficient buffer space to
report tx status.
Also, don't reserve local->tx_headroom + local->hw.extra_tx_headroom.
Reported-by: Simon Morgenthaler <s.morgenthaler@students.unibe.ch>
Reported-by: Kai Scharwies <kai@scharwies.de>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch workaround live deadlock problem caused by infinite loop
in brcms_c_wait_for_tx_completion(). I do not consider the patch as
the proper fix, which should fix the real reason of tx queue flush
failure, but patch helps with system lockup.
Reference:
https://bugzilla.kernel.org/show_bug.cgi?id=42576
Reported-and-tested-by: Patrick <ragamuffin@datacomm.ch>
Cc: stable@vger.kernel.org # 3.2+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since stations moved into a virtual interface
subdirectory, this link has been broken. Fix it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
tg3: Fix single-vector MSI-X code
openvswitch: Fix multipart datapath dumps.
ipv6: fix per device IP snmp counters
inetpeer: initialize ->redirect_genid in inet_getpeer()
net: fix NULL-deref in WARN() in skb_gso_segment()
net: WARN if skb_checksum_help() is called on skb requiring segmentation
caif: Remove bad WARN_ON in caif_dev
caif: Fix typo in Vendor/Product-ID for CAIF modems
bnx2x: Disable AN KR work-around for BCM57810
bnx2x: Remove AutoGrEEEn for BCM84833
bnx2x: Remove 100Mb force speed for BCM84833
bnx2x: Fix PFC setting on BCM57840
bnx2x: Fix Super-Isolate mode for BCM84833
net: fix some sparse errors
net: kill duplicate included header
net: sh-eth: Fix build error by the value which is not defined
net: Use device model to get driver name in skb_gso_segment()
bridge: BH already disabled in br_fdb_cleanup()
net: move sock_update_memcg outside of CONFIG_INET
mwl8k: Fixing Sparse ENDIAN CHECK warning
...
Kdump kernels leave MSI-X interrupts (as setup by the crashed kernel)
enabled. However, kdump only enables one CPU in the new environment,
thus causing tg3 to abort MSI-X setup. When the driver attempts to
enable INTA or MSI interrupt modes on a kdump kernel, interrupt
delivery fails.
This patch attempts to workaround the problem by forcing the driver
to enable a single MSI-X interrupt. In such a configuration, the
device's multivector interrupt mode must be disabled.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic to split up the list of datapaths into multiple Netlink messages
was simply wrong, causing the list to be terminated after the first part.
Only about the first 50 datapaths would be dumped. This fixes the
problem.
Reported-by: Paul Ingram <paul@nicira.com>
Signed-off-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 4ce3c183fc (snmp: 64bit ipstats_mib for all arches), I forgot
to change the /proc/net/dev_snmp6/xxx output for IP counters.
percpu array is 64bit per counter but the folding still used the 'long'
variant, and output garbage on 32bit arches.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some fallout from the 3.3. merge window as well as a couple bug fixes
for older preexisting bugs that seem valid to include at this time:
* sched_clock changes broke picoxcell, fix included
* BSYM bugs causing issues with thumb2-built kernels on SMP
* Missing module.h include on msm.
* A collection of bugfixes for samsung platforms that didn't make it into
the first pull requests.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=+GJ1
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
ARM: fixes for ARM platforms
Some fallout from the 3.3. merge window as well as a couple bug fixes
for older preexisting bugs that seem valid to include at this time:
* sched_clock changes broke picoxcell, fix included
* BSYM bugs causing issues with thumb2-built kernels on SMP
* Missing module.h include on msm.
* A collection of bugfixes for samsung platforms that didn't make it into
the first pull requests.
* tag 'arm-soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: make BSYM macro assembly only
ARM: highbank: remove incorrect BSYM usage
ARM: imx: remove incorrect BSYM usage
ARM: exynos: remove incorrect BSYM usage
ARM: ux500: add missing ENDPROC to headsmp.S
ARM: msm: Add missing ENDPROC to headsmp.S
ARM: versatile: Add missing ENDPROC to headsmp.S
ARM: EXYNOS: Invert VCLK polarity for framebuffer on ORIGEN
ARM: S3C64XX: Fix interrupt configuration for PCA935x on Cragganmore
ARM: S3C64XX: Fix the memory mapped GPIOs on Cragganmore
ARM: S3C64XX: Remove hsmmc1 from Cragganmore
ARM: S3C64XX: Remove unconditional power domain disables
ARM: SAMSUNG: Declare struct platform_device in plat/s3c64xx-spi.h
ARM: SAMSUNG: dma-ops.h needs mach/dma.h
ARM: SAMSUNG: Guard against multiple inclusion of plat/dma.h
ARM: picoxcell: fix sched_clock() cleanup fallout
ARM: msm: vreg is a module and so needs module.h
* 'upstream-linus' of git://github.com/jgarzik/libata-dev:
[libata] ata_piix: Add Toshiba Satellite Pro A120 to the quirks list due to broken suspend functionality.
[libata] add DVRTD08A and DVR-215 to NOSETXFER device quirk list
[libata] pata_bf54x: Support sg list in bmdma transfer.
[libata] sata_fsl: fix the controller operating mode
[libata] enable ata port async suspend
JONGMAN HEO reports:
With current linus git (commit a25a2b84), I got following build error,
arch/x86/kernel/vm86_32.c: In function 'do_sys_vm86':
arch/x86/kernel/vm86_32.c:340: error: implicit declaration of function '__audit_syscall_exit'
make[3]: *** [arch/x86/kernel/vm86_32.o] Error 1
OK, I can reproduce it (32bit allmodconfig with AUDIT=y, AUDITSYSCALL=n)
It's due to commit d7e7528bcd: "Audit: push audit success and retcode
into arch ptrace.h".
Reported-by: JONGMAN HEO <jongman.heo@samsung.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
BF54x on-chip ATAPI controller allows maximum 0x1fffe bytes to be transfered
in one ATAPI transfer. So, set the max sg_tablesize to 4.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Configure the FSL SATA controller to the preferred, enterprise mode.
Signed-off-by: Yutaka Ando <r46913@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit: (29 commits)
audit: no leading space in audit_log_d_path prefix
audit: treat s_id as an untrusted string
audit: fix signedness bug in audit_log_execve_info()
audit: comparison on interprocess fields
audit: implement all object interfield comparisons
audit: allow interfield comparison between gid and ogid
audit: complex interfield comparison helper
audit: allow interfield comparison in audit rules
Kernel: Audit Support For The ARM Platform
audit: do not call audit_getname on error
audit: only allow tasks to set their loginuid if it is -1
audit: remove task argument to audit_set_loginuid
audit: allow audit matching on inode gid
audit: allow matching on obj_uid
audit: remove audit_finish_fork as it can't be called
audit: reject entry,always rules
audit: inline audit_free to simplify the look of generic code
audit: drop audit_set_macxattr as it doesn't do anything
audit: inline checks for not needing to collect aux records
audit: drop some potentially inadvisable likely notations
...
Use evil merge to fix up grammar mistakes in Kconfig file.
Bad speling and horrible grammar (and copious swearing) is to be
expected, but let's keep it to commit messages and comments, rather than
expose it to users in config help texts or printouts.
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: cleanup xfs_file_aio_write
xfs: always return with the iolock held from xfs_file_aio_write_checks
xfs: remove the i_new_size field in struct xfs_inode
xfs: remove the i_size field in struct xfs_inode
xfs: replace i_pin_wait with a bit waitqueue
xfs: replace i_flock with a sleeping bitlock
xfs: make i_flags an unsigned long
xfs: remove the if_ext_max field in struct xfs_ifork
xfs: remove the unused dm_attrs structure
xfs: cleanup xfs_iomap_eof_align_last_fsb
xfs: remove xfs_itruncate_data
* 'btrfs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
btrfs: take allocation of ->tree_root into open_ctree()
btrfs: let ->s_fs_info point to fs_info, not root...
btrfs: consolidate failure exits in btrfs_mount() a bit
btrfs: make free_fs_info() call ->kill_sb() unconditional
btrfs: merge free_fs_info() calls on fill_super failures
btrfs: kill pointless reassignment of ->s_fs_info in btrfs_fill_super()
btrfs: make open_ctree() return int
btrfs: sanitizing ->fs_info, part 5
btrfs: sanitizing ->fs_info, part 4
btrfs: sanitizing ->fs_info, part 3
btrfs: sanitizing ->fs_info, part 2
btrfs: sanitizing ->fs_info, part 1
btrfs: fix a deadlock in btrfs_scan_one_device()
btrfs: fix mount/umount race
btrfs: get ->kill_sb() of its own
btrfs: preparation to fixing mount/umount race
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (62 commits)
Btrfs: use larger system chunks
Btrfs: add a delalloc mutex to inodes for delalloc reservations
Btrfs: space leak tracepoints
Btrfs: protect orphan block rsv with spin_lock
Btrfs: add allocator tracepoints
Btrfs: don't call btrfs_throttle in file write
Btrfs: release space on error in page_mkwrite
Btrfs: fix btrfsck error 400 when truncating a compressed
Btrfs: do not use btrfs_end_transaction_throttle everywhere
Btrfs: add balance progress reporting
Btrfs: allow for resuming restriper after it was paused
Btrfs: allow for canceling restriper
Btrfs: allow for pausing restriper
Btrfs: add skip_balance mount option
Btrfs: recover balance on mount
Btrfs: save balance parameters to disk
Btrfs: soft profile changing mode (aka soft convert)
Btrfs: implement online profile changing
Btrfs: do not reduce profile in do_chunk_alloc()
Btrfs: virtual address space subset filter
...
Fix up trivial conflict in fs/btrfs/ioctl.c due to the use of the new
mnt_drop_write_file() helper.
Similar to SIGNATURE, rename INTEGRITY_DIGSIG to INTEGRITY_SIGNATURE.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: James Morris <jmorris@namei.org>
As modules are expected to select MPILIB, MPILIB_EXTRA, and SIGNATURE,
removed Kconfig prompts.
Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: James Morris <jmorris@namei.org>
It was reported that description of the MPILIB_EXTRA is confusing.
Indeed it was copy-paste typo. It is fixed here.
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: James Morris <jmorris@namei.org>
It was reported that DIGSIG is confusing name for digital signature
module. It was suggested to rename DIGSIG to SIGNATURE.
Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Suggested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: James Morris <jmorris@namei.org>
Enabling CONFIG_PROVE_RCU and CONFIG_SPARSE_RCU_POINTER resulted in
"suspicious rcu_dereference_check() usage!" and "incompatible types
in comparison expression (different address spaces)" messages.
Access the masterkey directly when holding the rwsem.
Changelog v1:
- Use either rcu_read_lock()/rcu_derefence_key()/rcu_read_unlock()
or remove the unnecessary rcu_derefence() - David Howells
Reported-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Define rcu_assign_keypointer(), which uses the key payload.rcudata instead
of payload.data, to resolve the CONFIG_SPARSE_RCU_POINTER message:
"incompatible types in comparison expression (different address spaces)"
Replace the rcu_assign_pointer() calls in encrypted/trusted keys with
rcu_assign_keypointer().
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Add missing smp_rmb() primitives to the keyring search code.
When keyring payloads are appended to without replacement (thus using up spare
slots in the key pointer array), an smp_wmb() is issued between the pointer
assignment and the increment of the key count (nkeys).
There should be corresponding read barriers between the read of nkeys and
dereferences of keys[n] when n is dependent on the value of nkeys.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
TOMOYO 2.5 in Linux 3.2 and later handles Unix domain socket's address.
Thus, tomoyo_correct_word2() needs to accept \000 as a valid character, or
TOMOYO 2.5 cannot handle Unix domain's abstract socket address.
Reported-by: Steven Allen <steven@stebalien.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
CC: stable@vger.kernel.org [3.2+]
Signed-off-by: James Morris <jmorris@namei.org>
This set of build failures just started appearing on parisc:
In file included from drivers/input/serio/serio_raw.c:12:
include/linux/kref.h: In function 'kref_get':
include/linux/kref.h:40: error: 'TAINT_WARN' undeclared (first use in this function)
include/linux/kref.h:40: error: (Each undeclared identifier is reported only once
include/linux/kref.h:40: error: for each function it appears in.)
include/linux/kref.h: In function 'kref_sub':
include/linux/kref.h:65: error: 'TAINT_WARN' undeclared (first use in this function)
It happens because TAINT_WARN is defined in kernel.h and this particular
compile doesn't seem to include it (no idea why it's just manifesting ..
probably some #include file untangling exposed it).
Fix by adding
#include <linux/kernel.h>
to linux/kref.h
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update MAINTAINERS file with new git repo:
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security.git
Signed-off-by: James Morris <jmorris@namei.org>
Jüri Aedla reported that the /proc/<pid>/mem handling really isn't very
robust, and it also doesn't match the permission checking of any of the
other related files.
This changes it to do the permission checks at open time, and instead of
tracking the process, it tracks the VM at the time of the open. That
simplifies the code a lot, but does mean that if you hold the file
descriptor open over an execve(), you'll continue to read from the _old_
VM.
That is different from our previous behavior, but much simpler. If
somebody actually finds a load where this matters, we'll need to revert
this commit.
I suspect that nobody will ever notice - because the process mapping
addresses will also have changed as part of the execve. So you cannot
actually usefully access the fd across a VM change simply because all
the offsets for IO would have changed too.
Reported-by: Jüri Aedla <asd@ut.ee>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
audit_log_d_path() injects an additional space before the prefix,
which serves no purpose and doesn't mix well with other audit_log*()
functions that do not sneak extra characters into the log.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Eric Paris <eparis@redhat.com>
The use of s_id should go through the untrusted string path, just to be
extra careful.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
In the loop, a size_t "len" is used to hold the return value of
audit_log_single_execve_arg(), which returns -1 on error. In that
case the error handling (len <= 0) will be bypassed since "len" is
unsigned, and the loop continues with (p += len) being wrapped.
Change the type of "len" to signed int to fix the error handling.
size_t len;
...
for (...) {
len = audit_log_single_execve_arg(...);
if (len <= 0)
break;
p += len;
}
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
This allows audit to specify rules in which we compare two fields of a
process. Such as is the running process uid != to the running process
euid?
Signed-off-by: Peter Moody <pmoody@google.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
This completes the matrix of interfield comparisons between uid/gid
information for the current task and the uid/gid information for inodes.
aka I can audit based on differences between the euid of the process and
the uid of fs objects.
Signed-off-by: Peter Moody <pmoody@google.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Rather than code the same loop over and over implement a helper function which
uses some pointer magic to make it generic enough to be used numerous places
as we implement more audit interfield comparisons
Signed-off-by: Eric Paris <eparis@redhat.com>
We wish to be able to audit when a uid=500 task accesses a file which is
uid=0. Or vice versa. This patch introduces a new audit filter type
AUDIT_FIELD_COMPARE which takes as an 'enum' which indicates which fields
should be compared. At this point we only define the task->uid vs
inode->uid, but other comparisons can be added.
Signed-off-by: Eric Paris <eparis@redhat.com>
This patch provides functionality to audit system call events on the
ARM platform. The implementation was based off the structure of the
MIPS platform and information in this
(http://lists.fedoraproject.org/pipermail/arm/2009-October/000382.html)
mailing list thread. The required audit_syscall_exit and
audit_syscall_entry checks were added to ptrace using the standard
registers for system call values (r0 through r3). A thread information
flag was added for auditing (TIF_SYSCALL_AUDIT) and a meta-flag was
added (_TIF_SYSCALL_WORK) to simplify modifications to the syscall
entry/exit. Now, if either the TRACE flag is set or the AUDIT flag is
set, the syscall_trace function will be executed. The prober changes
were made to Kconfig to allow CONFIG_AUDITSYSCALL to be enabled.
Due to platform availability limitations, this patch was only tested
on the Android platform running the modified "android-goldfish-2.6.29"
kernel. A test compile was performed using Code Sourcery's
cross-compilation toolset and the current linux-3.0 stable kernel. The
changes compile without error. I'm hoping, due to the simple modifications,
the patch is "obviously correct".
Signed-off-by: Nathaniel Husted <nhusted@gmail.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Just a code cleanup really. We don't need to make a function call just for
it to return on error. This also makes the VFS function even easier to follow
and removes a conditional on a hot path.
Signed-off-by: Eric Paris <eparis@redhat.com>
At the moment we allow tasks to set their loginuid if they have
CAP_AUDIT_CONTROL. In reality we want tasks to set the loginuid when they
log in and it be impossible to ever reset. We had to make it mutable even
after it was once set (with the CAP) because on update and admin might have
to restart sshd. Now sshd would get his loginuid and the next user which
logged in using ssh would not be able to set his loginuid.
Systemd has changed how userspace works and allowed us to make the kernel
work the way it should. With systemd users (even admins) are not supposed
to restart services directly. The system will restart the service for
them. Thus since systemd is going to loginuid==-1, sshd would get -1, and
sshd would be allowed to set a new loginuid without special permissions.
If an admin in this system were to manually start an sshd he is inserting
himself into the system chain of trust and thus, logically, it's his
loginuid that should be used! Since we have old systems I make this a
Kconfig option.
Signed-off-by: Eric Paris <eparis@redhat.com>
The function always deals with current. Don't expose an option
pretending one can use it for something. You can't.
Signed-off-by: Eric Paris <eparis@redhat.com>
