1. Rewrite of the non-dma data transfer functions to use only ONE mode
of TIMOD (TIMOD=0x1). With TIMOD=0, it was not possible to set the TX
bit pattern. So the TDBR = 0xFFFF inside the read calls won't work.
2. Clear SPI_RDBR before reading and before duplex transfer.
Otherwise the garbage data in RDBR will get read. Since mmc_spi uses a
lot of duplex transfers, this is the main cause of mmc_spi failure.
3. Poll RXS for transfer completion. Polling SPIF or TXS cannot
guarantee transfer completion. This may interrupt a transfer before it
is finished. Also this may leave garbage data in buffer and affect
next transfer.
[Yi Li <yi.li@analog.com>: add a field "u16 idle_tx_val" in "struct
bfin5xx_spi_chip" to specify the value to transmit if no TX value
is supplied.]
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for GPIO controlled SPI Chip Selects. To make use of this
feature, set chip_select = 0 and add a proper cs_gpio to your
controller_data.
struct spi_board_info
.chip_select = 0
struct bfin5xx_spi_chip
.cs_gpio = GPIO_P###
There are various SPI devices that require SPI MODE_0, and need to have
the Chip Selects asserted during the entire transfer. Consider using
SPI_MODE_3 (SPI_CPHA | SPI_CPOL) if your device allows it.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do this because when things crash, we get simple names like "setup" and
"start_queue" which is pretty difficult to trace back to the real thing:
the spi driver
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to comments in linux/spi/spi.h:
* All SPI transfers start with the relevant chipselect active. Normally
* it stays selected until after the last transfer in a message. Drivers
* can affect the chipselect signal using cs_change.
*
* (i) If the transfer isn't the last one in the message, this flag is
* used to make the chipselect briefly go inactive in the middle of the
* message. Toggling chipselect in this way may be needed to terminate
* a chip command, letting a single spi_message perform all of group of
* chip transactions together.
*
* (ii) When the transfer is the last one in the message, the chip may
* stay selected until the next transfer. On multi-device SPI busses
* with nothing blocking messages going to other devices, this is just
* a performance hint; starting a message to another device deselects
* this one. But in other cases, this can be used to ensure correctness.
* Some devices need protocol transactions to be built from a series of
* spi_message submissions, where the content of one message is determined
* by the results of previous messages and where the whole transaction
* ends when the chipselect goes intactive.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This bug can be observed when two SPI devices are sharing the spi bus: One
device is set as SPI CS 7, another one is using SPI CS 4.
In spi_bfin5xx.c: cs_active(), cs_deactive() are used to control SPI_FLG
register. From the debug bellow:
cs_active: flag: 0x7f91, chip->flag: 0x7f80, cs: 7
cs_active: flag: 0xef91, chip->flag: 0xef10, cs: 4
When device A (cs_7) activate CS 7, SPI_FLG is set as 0x7f91 (however,
SPI_FLG should be set as 0x7f80, or 0x6f91 if in broadcast mode).
Due to some HW bug (very possibly), if SPI_FLG is set as 0x7f91, SPISSEL7
is asserted, however SPISSEL4 will be asserted too (I can see this using
the scope). This is unreasonable according to HRM.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Without this change, SPI DMA is not reliably under stress tests.
Obiviously it's a hardware issue which is not addressed by any document.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "while" endless loop will cause the system hang if hardware error, so
we add timeout control to make the system alive.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When using a BF533-STAMP here with a W25X10 SPI flash. It works fine when
enable_dma is disabled, but doesn't work at all when turning DMA on. We
get just 0xff bytes back when trying to read the device.
Change the code around so that it programs the SPI first and then enables
DMA, it seems to work a lot better ...
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
use the properl BIT_CTL_... defines rather than the internal driv er
CFG_SPI_... defines
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We only need to check SPI error when DMA failes, cause that is the DMA IRQ
handling routine.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because of DMA hardware issue, we were trying to use software workaround.
This patch add some useful debug messages to help us debugging the DMA
code.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Blackfin's related DMA callback API doesn't need void * cast, so drop it.
And this driver is for all Blackfin processors not only for BF53x, we
update the DMA request label for more meaningful information.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For DMA TX/RX operation in pump_transfers, DMA contriguration code in TX
and RX paths are almost the same. This patch unify the duplicated DMA
code to make it more readable.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the SPI bus registers a receive overflow error, pass the result back up
to the higher levels.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use len_in_bytes when we care about the number of bytes transferred rather
than the number of spi transactions. (this value will be the same for
8bit transfers, but not any other sizes)
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We already moved bfin_addr_dcachable() and friends into the cacheflush
header where it belongs, so don't need to include <asm/cplbinit.h> here.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix erroneous SPI Clock divisor calculation. Make sure SPI_BAUD is always
>= 2. Writing a value of 0 or 1 to the SPI_BAUD register disables the
serial clock.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flush or invalidate caches before doing DMA transfer, if needed.
[Mike Frysinger <vapier.adi@gmail.com>: add comment to address the
issue "Full duplex only works for non-DMA transfers".]
Signed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This controller can be found on the D-Link DNS-323 for instance, where
it is to be configured via static i2c_board_info in the board-specific
mach-orion/dns323-setup.c; this driver supports only the new-style
driver model.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Matthew Palmer <mpalmer@debian.org>
Signed-off-by: Laurie Bradshaw <bradshaw.laurie@googlemail.com>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently, it's argued that what proc/pid/maps shows is ugly when a 32bit
binary runs on 64bit host.
/proc/pid/maps outputs vma's pgoff member but vma->pgoff is of no use
information is the vma is for ANON. With this patch, /proc/pid/maps shows
just 0 if no file backing store.
[akpm@linux-foundation.org: coding-style fixes]
[kamezawa.hiroyu@jp.fujitsu.com: coding-style fixes]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mike Waychison <mikew@google.com>
Reported-by: Ying Han <yinghan@google.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add /proc entries to give the admin the ability to control the minimum and
maximum number of pdflush threads. This allows finer control of pdflush
on both large and small machines.
The rationale is simply one size does not fit all. Admins on large and/or
small systems may want to tune the min/max pdflush thread count to best
suit their needs. Right now the min/max is hardcoded to 2/8. While
probably a fair estimate for smaller machines, large machines with large
numbers of CPUs and large numbers of filesystems/block devices may benefit
from larger numbers of threads working on different block devices.
Even if the background flushing algorithm is radically changed, it is
still likely that multiple threads will be involved and admins would still
desire finer control on the min/max other than to have to recompile the
kernel.
The patch adds '/proc/sys/vm/nr_pdflush_threads_min' and
'/proc/sys/vm/nr_pdflush_threads_max' with r/w permissions.
The minimum value for nr_pdflush_threads_min is 1 and the maximum value is
the current value of nr_pdflush_threads_max. This minimum is required
since additional thread creation is performed in a pdflush thread itself.
The minimum value for nr_pdflush_threads_max is the current value of
nr_pdflush_threads_min and the maximum value can be 1000.
Documentation/sysctl/vm.txt is also updated.
[akpm@linux-foundation.org: fix comment, fix whitespace, use __read_mostly]
Signed-off-by: Peter W Morreale <pmorreale@novell.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a race on creating pdflush threads. Without the patch, it is possible
to create more than MAX_PDFLUSH_THREADS threads, and this has been
observed in practice on IO loaded SMP machines.
The fix involves moving the lock around to protect the check against the
thread count and correctly dealing with thread creation failure.
This fix also _mostly_ repairs a race condition on how quickly the threads
are created. The original intent was to create a pdflush thread (up to
the max allowed) every second. Without this patch is is possible to
create NCPUS pdflush threads concurrently. The 'mostly' caveat is because
an assumption is made that thread creation will be successful. If we fail
to create the thread, the miss is not considered fatal. (we will try
again in 1 second)
Signed-off-by: Peter W Morreale <pmorreale@novell.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not critical.
WARNING: drivers/char/esp.o(.text+0x278): Section mismatch in reference from the function show_serial_version() to the variable .init.data:serial_version
The function show_serial_version() references
the variable __initdata serial_version.
This is often because show_serial_version lacks a __initdata
annotation or the annotation of serial_version is wrong.
WARNING: drivers/char/esp.o(.text+0x27d): Section mismatch in reference from the function show_serial_version() to the variable .init.data:serial_name
The function show_serial_version() references
the variable __initdata serial_name.
This is often because show_serial_version lacks a __initdata
annotation or the annotation of serial_name is wrong.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andrew J. Robinson <arobinso@nyx.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-module-and-param:
Revert "module: remove the SHF_ALLOC flag on the __versions section."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (28 commits)
powerpc: Fix oops when loading modules
powerpc: Wire up preadv and pwritev
powerpc/ftrace: Fix printf format warning
powerpc/ftrace: Fix #if that should be #ifdef
powerpc: Fix ptrace compat wrapper for FPU register access
powerpc: Print information about mapping hw irqs to virtual irqs
powerpc: Correct dependency of KEXEC
powerpc: Disable VSX or current process in giveup_fpu/altivec
powerpc/pseries: Enable relay in pseries_defconfig
powerpc/pseries: Fix ibm,client-architecture comment
powerpc/pseries: Scan for all events in rtasd
powerpc/pseries: Add dispatch dispersion statistics
powerpc: Clean up some prom printouts
powerpc: Print progress of ibm,client-architecture method
powerpc: Remove duplicated #include's
powerpc/pmac: Fix internal modem IRQ on Wallstreet PowerBook
powerpc/wdrtas: Update wdrtas_get_interval to use rtas_data_buf
fsl-diu-fb: Pass the proper device for dma mapping routines
powerpc/pq2fads: Update device tree for use with device-tree-aware u-boot.
cpm_uart: Disable CPM udbg when re-initing CPM uart, even if not the console.
...
If ramfs mount fails, s_fs_info will be freed twice in ramfs_fill_super()
and ramfs_kill_sb(), leading to kernel oops.
Consolidate and beautify the code.
Make sure s_fs_info and s_root are in known good states.
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 9cb610d8e3.
This was an impressively stupid patch. Firstly, we reset the SHF_ALLOC
flag lower down in the same function, so the patch was useless. Even
better, find_sec() ignores sections with SHF_ALLOC not set, so
it breaks CONFIG_MODVERSIONS=y with CONFIG_MODULE_FORCE_LOAD=n, which
refuses to load the module since it can't find the __versions section.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Since TOMOYO's policy management tools does not use the "undelete domain"
command, we decided to remove that command.
Signed-off-by: Kentaro Takeda <takedakn@nttdata.co.jp>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Toshiharu Harada <haradats@nttdata.co.jp>
Signed-off-by: James Morris <jmorris@namei.org>
This fixes a problem reported by Sean MacLennan where loading any
module would cause an oops. We weren't marking the pages containing
the module text as having hardware execute permission, due to a bug
introduced in commit 8d1cf34e ("powerpc/mm: Tweak PTE bit combination
definitions"), hence trying to execute the module text caused an
exception on processors that support hardware execute permission.
This adds _PAGE_HWEXEC to the definitions of PAGE_KERNEL_X and
PAGE_KERNEL_ROX to fix this problem.
Reported-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
[paulus@samba.org: changed to use syscall numbers 320 and 321 since
perf_counters is currently using 319.]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
'tramp' is an unsigned long, so print it with %lx.
Fixes the following build warning:
arch/powerpc/kernel/ftrace.c:291: error: format ‘%x’ expects type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit bb7253403f ("powerpc64,
ftrace: save toc only on modules for function graph"), added an
#if CONFIG_PPC64. This changes it to #ifdef.
Fixes the following warning on 32-bit builds:
arch/powerpc/kernel/ftrace.c:562:5: error: "CONFIG_PPC64" is not defined
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ptrace compat wrapper mishandles access to the fpu registers. The
PTRACE_PEEKUSR and PTRACE_POKEUSR requests miscalculate the index into
the fpr array due to the broken FPINDEX macro. The
PPC_PTRACE_PEEKUSR_3264 request needs to use the same formula that the
native ptrace interface uses when operating on the register number (as
opposed to the 4-byte offset). The PPC_PTRACE_POKEUSR_3264 request
didn't take TS_FPRWIDTH into account.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The irq remapping layer seems to cause some confusion when people
see a different irq number in /proc/interrupts vs the one they
request in their driver or DTS.
So have the irq remapping layer print out a message when we map an
irq. The message is only printed the first time the irq is mapped,
and it's KERN_DEBUG so most people won't see it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
commit 28794d34ec ("powerpc/kconfig: Kill
PPC_MULTIPLATFORM") broke KEXEC, by making it dependent on BOOK3S, while it
should be PPC_BOOK3S.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we call giveup_fpu, we need to need to turn off VSX for the
current process. If we don't, on return to userspace it may execute a
VSX instruction before the next FP instruction, and not have its
register state refreshed correctly from the thread_struct. Ditto for
altivec.
This caused a bug where an unaligned lfs or stfs results in
fix_alignment calling giveup_fpu so it can use the FPRs (in order to
do a single <-> double conversion), and then returning to userspace
with FP off but VSX on. Then if a VSX instruction is executed, before
another FP instruction, it will proceed without another exception and
hence have the incorrect register state for VSX registers 0-31.
lfs unaligned <- alignment exception turns FP off but leaves VSX on
VSX instruction <- no exception since VSX on, hence we get the
wrong VSX register values for VSX registers 0-31,
which overlap the FPRs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Enable relay in pseries config, ppc64_defconfig had it enabled but pseries
did not.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Instead of checking for known events, pass in all 1s so we handle future
event types. We were currently missing the IO event type.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PHYP tells us how often a shared processor dispatch changed physical cpus.
This can highlight performance problems caused by the hypervisor.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make all messages consistent, some have spaces before the "...", some do not.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ibm,client-architecture method will often cause a reconfiguration reboot.
When this happens the last thing we see is:
Hypertas detected, assuming LPAR !
Which doesn't explain what just happened. Wrap the ibm,client-architecture
so it's clear what is going on:
Calling ibm,client-architecture... done
In order to maintain the law of conservation of screen real estate, downgrade
two other messages to debug.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The (relatively) new pmac_zilog driver doesn't use the pre-munged
IRQ numbers from the macio_dev unlike other macio things, it
directly maps it off the OF device-tree.
It does that because it can be initialized much earlier than the
registration of the macio devices, in order to get a serial
console early.
Unfortunately, that means that it "misses" some fixups done
by the macio layer to work around missing interrupt descriptions
in the device-tree of the Wallstreet machines.
This patch brings the necessary workaround into the pmac_zilog
driver itself to bring it back to working condition.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The buffer passed to the ibm,get-system-parameter RTAS call must be
in the RMA. To ensure we pass an address in the RMA use rtas_data_buf
for the actual RTAS call and then copy the result to value. We can't
just make it static because this can be compiled in as a module.
Also add the WDRTAS_SP_SPI_LEN so we don't litter '4' throughout the
function.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Tested-by: Adrian Reber <adrian@lisas.de>
Acked-by: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
