Enable Silicon Labs Ember VID chips to enumerate with the cp210x usb serial
driver. EM358x devices operating with the Ember Z-Net 5.1.2 stack may now
connect to host PCs over a USB serial link.
Signed-off-by: Nathaniel Ting <nathaniel.ting@silabs.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Here's the big tty/serial driver patchset for 3.18-rc1.
Lots of little things in here, some good work from Peter Hurley on the
tty core, and in lots of drivers. There are also lots of other driver
updates in here as well, full details in the changelog below.
All have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQ0aDwACgkQMUfUDdst+ymueACeI1i2exlGaBBSVQuUK2Jmx8Uz
nukAn3KPuvvx+MKfMMBRpK0DQCzTxv4P
=dwv1
-----END PGP SIGNATURE-----
Merge tag 'tty-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the big tty/serial driver patchset for 3.18-rc1.
Lots of little things in here, some good work from Peter Hurley on the
tty core, and in lots of drivers. There are also lots of other driver
updates in here as well, full details in the changelogs.
All have been in the linux-next tree for a while"
* tag 'tty-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (99 commits)
Revert "serial/core: Initialize the console pm state"
tty: serial: 8250: use 32bit variable for rpm_tx_active
tty: serial: msm: Add earlycon support
serial/core: Initialize the console pm state
serial: asc: Conditionally use readl_relaxed (COMPILE_TEST)
serial: of-serial: add PM suspend/resume support
m68k: AMIGA_BUILTIN_SERIAL should depend on TTY
asm/uapi: Add definition of TIOC[SG]RS485
tty/metag_da: Add console_poll module parameter
serial: 8250_pci: remove rts_n override from Baytrail quirk
serial: cadence: Add generic earlycon support
serial: imx: change the wait even to interruptiable
serial: imx: terminate the RX DMA when the UART is suspending
serial: imx: fix throttle/unthrottle callbacks for hardware assisted flow control
serial: 8250: Add Quark X1000 to 8250_pci.c
tty: omap-serial: pull out calculation from baud_is_mode16
tty: omap-serial: fix division by zero
xen_hvc: no reason to write the type key on xenstore
tty: serial: 8250_core: remove UART_IER_RDI in serial8250_stop_rx()
tty: serial: 8250_core: use the ->line argument as a hint in serial8250_find_match_or_unused()
...
Here are two more device IDs for v3.17.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=G51o
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.17-final' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial fixes for v3.17
Here are two more device IDs for v3.17.
Signed-off-by: Johan Hovold <johan@kernel.org>
The tty core does not test tty->hw_stopped; remove from drivers
which don't test it themselves.
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added the Seluxit ApS USB Serial Dongle to cp210x driver.
Signed-off-by: Andreas Bomholtz <andreas@seluxit.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Added support for Ketra N1 wireless interface, which uses the
Silicon Labs' CP2104 USB to UART bridge with customized PID 8946.
Signed-off-by: Joe Savage <joe.savage@goketra.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The zte_ev driver is based on code (once) distributed by ZTE that still
appears to originally have been reverse-engineered and bolted onto the
generic driver.
A closer analysis of the zte_ev setup code reveals that it consists of
standard CDC requests (SET/GET_LINE_CODING and SET_CONTROL_LINE_STATE)
but unfortunately fails to get some of those right. In particular, as
reported by Lei Liu, it fails to lower DTR/RTS on close. It also appears
that the control requests lack the interface argument.
Since line control is already handled properly by the option driver, and
the SET/GET_LINE_CODING requests appears to be redundant (amounts to a
SET 9600 8N1) let's remove the redundant zte_ev driver.
Also move the remaining ZTE PIDs to the generic option modem driver.
Reported-by: Lei Liu <liu.lei78@zte.com.cn>
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUFjfVAAoJEHm+PkMAQRiGANkIAIU3PNrAz9dIItq8a/rEAhnx
l2shHoOyEmyNR2apholM3BPUNX50cbsc/HGdi7lZKLkA/ifAj6B9nFD2NzVsIChD
1QWVcvdkKlVuxXCDd26qbijlfmbTOAWrLw9ntvM+J6ZtECM6zCAZF4MAV/FwogPq
ETGKD76AxJtVIhBMS99troAiC1YxmQ7DKgEr8CraTOR1qwXEonnPCmN/IZA6x2/G
EXiihOuQB5me1X7k4PI0V8CDscQOn+3B2CQHIrjRB+KiTF+iKIuI8n6ORC6bpFh+
U8UZP9wLlIG1BrUHG83pIndglIHotqPcjmtfl1WGrRr2hn7abzVSfV+g5Syo3Vg=
=Ep+s
-----END PGP SIGNATURE-----
Merge tag 'v3.17-rc5' into usb-next
USB fixes in Linux 3.17-rc5 are needed to build on top of for 3.18.
Signed-off-by: Johan Hovold <johan@kernel.org>
Probe is testing if the current interface provides two bulk endpoints.
While this achieves the goal of only binding to the correct interface,
we already know we can find the device on interface number 1. Stop
checking the endpoints and just return successfully when interface
number 1 is probed.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add simple driver for Medtronic CareLink USB devices.
Reported-by: Benjamin West <bewest@gmail.com>
Tested-by: Benjamin West <bewest@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use direct method for supported baud rates, otherwise use divisors.
Limit baud rate to 12 Mbaud with HX type.
This change has been tested to work with PL-2303HX at 115200, 500000,
1000000, 2000000, 2500000, 3000000 and 4000000 baud rates.
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
This VID:PID is used for some Direct IP devices behaving
identical to the already supported 0F3D:68AA devices.
Cc: <stable@vger.kernel.org>
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Sierra Wireless Direct IP devices using the 68A3 product ID
can be configured for modes including a CDC ECM class function.
The known example uses interface numbers 12 and 13 for the ECM
control and data interfaces respectively, consistent with CDC
MBIM function interface numbering on other Sierra devices.
It seems cleaner to restrict this driver to the ff/ff/ff
vendor specific interfaces rather than increasing the already
long interface number blacklist. This should be more future
proof if Sierra adds more class functions using interface
numbers not yet in the blacklist.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add device id for NOVITUS Bono E thermal printer.
Reported-by: Emanuel Koczwara <poczta@emanuelkoczwara.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add back some PIDs that were mistakingly remove when reverting commit
73228a0538 ("USB: option,zte_ev: move most ZTE CDMA devices to
zte_ev"), which apparently did more than its commit message claimed in
that it not only moved some PIDs from option to zte_ev but also added
some new ones.
Fixes: 63a901c06e ("Revert "USB: option,zte_ev: move most ZTE CDMA
devices to zte_ev"")
Reported-by: Lei Liu <lei35151@163.com>
Cc: stable <stable@vger.kernel.org>
Make sure to verify the number of ports requested by subdriver to avoid
writing beyond the end of fixed-size array in interface data.
The current usb-serial implementation is limited to eight ports per
interface but failed to verify that the number of ports requested by a
subdriver (which could have been determined from device descriptors) did
not exceed this limit.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to verify the maximum number of endpoints per type to avoid
writing beyond the end of a stack-allocated array.
The current usb-serial implementation is limited to eight ports per
interface but failed to verify that the number of endpoints of a certain
type reported by a device did not exceed this limit.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a potential security issue in the whiteheat USB driver
which might allow a local attacker to cause kernel memory corrpution. This
is due to an unchecked memcpy into a fixed size buffer (of 64 bytes). On
EHCI and XHCI busses it's possible to craft responses greater than 64
bytes leading a buffer overflow.
Signed-off-by: James Forshaw <forshaw@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added support to the ftdi_sio driver for ekey Converter USB which
uses an FT232BM chip.
Signed-off-by: Jaša Bartelj <jasa.bartelj@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds a new device id to the pl2303 driver for the ZTEK device.
Reported-by: Mike Chu <Mike-Chu@prolific.com.tw>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add device id for Basic Micro ATOM Nano USB2Serial adapters.
Reported-by: Nicolas Alt <n.alt@mytum.de>
Tested-by: Nicolas Alt <n.alt@mytum.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove dublicate Qualcom PID 0x3197 which is already handled by the
moto-modem driver since commit 6986a978ee ("USB: add new moto_modem
driver for some Morotola phones").
Fixes: 799ee9243d ("USB: serial: add zte_ev.c driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove dublicate Gobi PID 0x9008 which is already handled by the
qcserial driver since commit f05932c0ca ("USB: qcserial: Add extra
device IDs").
Fixes: 799ee9243d ("USB: serial: add zte_ev.c driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit 73228a0538 ("USB: option,zte_ev: move most ZTE
CDMA devices to zte_ev").
Move the IDs of the devices that were previously driven by the option
driver back to that driver.
As several users have reported, the zte_ev driver is causing random
disconnects as well as reconnect failures.
A closer analysis of the zte_ev setup code reveals that it consists of
standard CDC requests (SET/GET_LINE_CODING and SET_CONTROL_LINE_STATE)
but unfortunately fails to get some of those right. In particular, as
reported by Liu Lei, it fails to lower DTR/RTS on close. It also appears
that the control requests lack the interface argument.
Note that the zte_ev driver is based on code (once) distributed by ZTE
that still appears to originally have been reverse-engineered and bolted
onto the generic driver.
Since line control is already handled properly by the option driver, and
the SET/GET_LINE_CODING requests appears to be redundant (amounts to a
SET 9600 8N1), this is a first step in ultimately removing the redundant
zte_ev driver.
Note that AC2726 had already been moved back to option, and that some
IDs were in the device table of both drivers prior to the commit being
reverted.
Reported-by: Lei Liu <liu.lei78@zte.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This VIA Telecom baseband processor is used is used by by u-blox in both the
FW2770 and FW2760 products and may be used in others as well.
This patch has been tested on both of these modem versions.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Do not log normal interrupt-urb shutdowns as errors.
The option driver has always been logging any nonzero interrupt-urb
status as an error, including when the urb is killed during normal
operation.
Commit 9096f1fbba ("USB: usb_wwan: fix potential NULL-deref at
resume") moved the interrupt urb submission from port probe and release
to open and close, thus potentially increasing the number of these
false-positive error messages dramatically.
Reported-by: Ed Butler <ressy66@ausics.net>
Tested-by: Ed Butler <ressy66@ausics.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds support for new Xsens devices, using Xsens' own Vendor ID.
Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com>
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The converters are used in specific products. It can be useful to know
which they are exactly.
Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com>
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This `usb_reset_device` command has been around since the driver was
originally reverse engineered. It doesn't cause much issue on single
interface CP210x devices, but on the CP2105 and CP2108 with 2 and 4
interfaces respectively it will cause instability on enumeration and
delays enumeration noticably. There should be no reason to reset a device
at startup, per the CP210x AN571 spec.
Signed-off-by: Preston Fick <preston.fick@silabs.com>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some minor fixes and clean-ups to the ftdi_sio, mos7840 and kl5kusb105
drivers for v3.17-rc1.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=tUqf
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v3.17-rc1
Here are some minor fixes and clean-ups to the ftdi_sio, mos7840 and kl5kusb105
drivers for v3.17-rc1.
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds PID 0x0003 to the VID 0x128d (Testo). At least the
Testo 435-4 uses this, likely other gear as well.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch remove the function klsi_105_tiocmset which was only
returning -EINVAL. It also removes the function prototype and
the .tiocmset entry in the struct usb_serial_driver.
Verified by compilation only.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch remove the function klsi_105_tiocmset which was only
returning -EINVAL. It also removes the function prototype and
the .tiocmset entry in the struct usb_serial_driver.
Verified by compilation only.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add ID of the Telewell 4G v2 hardware to option driver to get legacy
serial interface working
Signed-off-by: Bernd Wachter <bernd.wachter@jolla.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Corsair USB Dongles are shipped with Corsair AXi series PSUs.
These are cp210x serial usb devices, so make driver detect these.
I have a program, that can get information from these PSUs.
Tested with 2 different dongles shipped with Corsair AX860i and
AX1200i units.
Signed-off-by: Andras Kovacs <andras@sth.sze.hu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove redundant mtxorb quirk used to fix up incorrect wMaxPacketSize,
which was added before 895f28badc ("USB: ftdi_sio: fix hi-speed device
packet size calculation") which does the same thing for all devices.
Signed-off-by: Johan Hovold <johan@kernel.org>
Promote max-packet-size-override message to warning level and use the
port device for logging, while using actual endpoint numbers in the
message itself.
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to print the number of endpoints per interface or
endpoint wMaxPacketSize during port probe. This information is readily
available using lsusb should it ever be needed.
Note that this also fixes the wMaxPacketSize being incorrectly reported
on big-endian systems due to a missing le16_to_cpu().
Signed-off-by: Johan Hovold <johan@kernel.org>
Adding a couple of Olivetti modems and blacklisting the net
function on a couple which are already supported.
Reported-by: Lars Melin <larsm17@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference when probing an interface with no
endpoints.
These devices have two bulk endpoints per interface, but this avoids
crashing the kernel if a user forces a non-FTDI device to be probed.
Note that the iterator variable was made unsigned in order to avoid
a maybe-uninitialized compiler warning for ep_desc after the loop.
Fixes: 895f28badc ("USB: ftdi_sio: fix hi-speed device packet size
calculation")
Reported-by: Mike Remski <mremski@mutualink.net>
Tested-by: Mike Remski <mremski@mutualink.net>
Cc: <stable@vger.kernel.org> # 2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Reported by Alif Mubarak Ahmad:
This device vendor and product id is 1c9e:9800
It is working as serial interface with generic usbserial driver.
I thought it is more suitable to use usbserial option driver, which has
better capability distinguishing between modem serial interface and
micro sd storage interface.
[ johan: style changes ]
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Alif Mubarak Ahmad <alive4ever@live.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Now that 3.15 is released, this merges the 'next' branch into 'master',
bringing us to the normal situation where my 'master' branch is the
merge window.
* accumulated work in next: (6809 commits)
ufs: sb mutex merge + mutex_destroy
powerpc: update comments for generic idle conversion
cris: update comments for generic idle conversion
idle: remove cpu_idle() forward declarations
nbd: zero from and len fields in NBD_CMD_DISCONNECT.
mm: convert some level-less printks to pr_*
MAINTAINERS: adi-buildroot-devel is moderated
MAINTAINERS: add linux-api for review of API/ABI changes
mm/kmemleak-test.c: use pr_fmt for logging
fs/dlm/debug_fs.c: replace seq_printf by seq_puts
fs/dlm/lockspace.c: convert simple_str to kstr
fs/dlm/config.c: convert simple_str to kstr
mm: mark remap_file_pages() syscall as deprecated
mm: memcontrol: remove unnecessary memcg argument from soft limit functions
mm: memcontrol: clean up memcg zoneinfo lookup
mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
mm/mempool.c: update the kmemleak stack trace for mempool allocations
lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
mm: introduce kmemleak_update_trace()
mm/kmemleak.c: use %u to print ->checksum
...
A set of new VID/PIDs retrieved from the out-of-tree GobiNet/GobiSerial
Sierra Wireless drivers.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Link: http://marc.info/?l=linux-usb&m=140136310027293&w=2
Cc: <stable@vger.kernel.org> # backport in link above
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move control-urb dereference to after NULL-check. There is otherwise a
risk of a possible null pointer dereference.
Was largely found by using a static code analysis program called
cppcheck.
[Johan: modify commit message somewhat ]
[gkh: remove stable tag as it's not a real problem that anyone has ever hit]
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NovaTech OrionLXm uses an onboard FTDI serial converter for JTAG and
console access.
Here is the lsusb output:
Bus 004 Device 123: ID 0403:7c90 Future Technology Devices
International, Ltd
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent patch that purported to fix firmware download on big-endian
machines failed to add the corresponding sparse annotation to the
i2c-header. This was reported by the kbuild test robot.
Adding the appropriate annotation revealed another endianess bug related
to the i2c-header Size-field in a code path that is exercised when the
firmware is actually being downloaded (and not just verified and left
untouched unless older than the firmware at hand).
This patch adds the required sparse annotation to the i2c-header and
makes sure that the Size-field is sent in little-endian byte order
during firmware download also on big-endian machines.
Note that this patch is only compile-tested, but that there is no
functional change for little-endian systems.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Ludovic Drolez <ldrolez@debian.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix incorrect pipe directions and remove bogus data buffer arguments
from control requests without data stage.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only way a port pointer may be NULL is if probe() failed, and in
that case neither disconnect(), resume(), or reset_resume() will be
called.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only call usb_autopm_put_interface() if the corresponding
usb_autopm_get_interface() was successful.
This prevents a potential runtime PM counter imbalance should
usb_autopm_get_interface() fail. Note that the USB PM usage counter is
reset when the interface is unbound, but that the runtime PM counter may
be left unbalanced.
Also add comment on why we don't need to worry about racing
resume/suspend on autopm_get failures.
Fixes: d5fd650cfc ("usb: serial: prevent suspend/resume from racing
against probe/remove")
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use tty-port initialised flag rather than private flag to determine when
port is closing down.
Since the tty-port flag is set prior to dropping DTR/RTS (when HUPCL is
set) this avoid submitting the read urbs when resuming the interface in
dtr_rts() only to immediately kill them again in shutdown().
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Promote failed-submission messages in open() and write() to error log
level.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_wwan_send_setup() function has never existed.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove some more outdated or superfluous comments.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove superfluous and cryptic comment from close.
It should be obvious that we're balancing the autopm_put in open (and
that operation already mentions the autopm_get done in the USB serial
core).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up and rename delay-urb submission function using a more
descriptive name.
Also add comment on locking assumptions.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use usb_get_serial_data() rather than accessing the private pointer
directly.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the port interrupt URB is submitted by the subdriver at open, we
should also kill it explicitly at suspend (even though this will be
taken care of by USB serial core otherwise).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant usb_kill_urb from port remove, which is called
post-shutdown (close).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver does not implement set_termios so the operation can be left
unset (tty will do the tty_termios_copy_hw for us).
Note that the send_setup call is bogus as it really only sets DTR/RTS
to their current values.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty-port implementation has already made sure that DTR/RTS have been
raised by calling dtr_rts so remove the redundant call from open.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that needs_remote_wake up is always set when there are open
ports.
Currently close() would unconditionally set needs_remote_wakeup to 0
even though there might still be open ports. This could lead to blocked
input and possibly dropped data on devices that do not support remote
wakeup (and which must therefore not be runtime suspended while open).
Add an open_ports counter (protected by the susp_lock) and only clear
needs_remote_wakeup when the last port is closed.
Note that there are currently no multi-port drivers using the usb_wwan
implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no reason not to try sending off any further delayed write urbs,
should one urb-submission fail.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep trying to submit urbs rather than bail out on first read-urb
submission error, which would also prevent I/O for any further ports
from being resumed.
Instead keep an error count, for all types of failed submissions, and
let USB core know that something went wrong.
Also make sure to always clear the suspended flag. Currently a failed
read-urb submission would prevent cached writes as well as any
subsequent writes from being submitted until next suspend-resume cycle,
something which may not even necessarily happen.
Note that USB core currently only logs an error if an interface resume
failed.
Fixes: 383cedc3bb ("USB: serial: full autosuspend support for the
option driver")
Cc: <stable@vger.kernel.org> # v2.6.32
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt urb was submitted unconditionally at resume, something
which could lead to a NULL-pointer dereference in the urb completion
handler as resume may be called after the port and port data is gone.
Fix this by making sure the interrupt urb is only submitted and active
when the port is open.
Fixes: 383cedc3bb ("USB: serial: full autosuspend support for the
option driver")
Cc: <stable@vger.kernel.org> # v2.6.32: 032129cb03
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The delayed-write queue was never emptied at shutdown (close), something
which could lead to leaked urbs if the port is closed before being
runtime resumed due to a write.
When this happens the output buffer would not drain on close
(closing_wait timeout), and after consecutive opens, writes could be
corrupted with previously buffered data, transfered with reduced
throughput or completely blocked.
Note that unbusy_queued_urb() was simply moved out of CONFIG_PM.
Fixes: 383cedc3bb ("USB: serial: full autosuspend support for the
option driver")
Cc: <stable@vger.kernel.org> # v2.6.32
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix race between write() and suspend() which could lead to writes being
dropped (or I/O while suspended) if the device is runtime suspended
while a write request is being processed.
Specifically, suspend() releases the susp_lock after determining the
device is idle but before setting the suspended flag, thus leaving a
window where a concurrent write() can submit an urb.
Fixes: 383cedc3bb ("USB: serial: full autosuspend support for the
option driver")
Cc: <stable@vger.kernel.org> # v2.6.32
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We find a race between write and resume. usb_wwan_resume run play_delayed()
and spin_unlock, but intfdata->suspended still is not set to zero.
At this time usb_wwan_write is called and anchor the urb to delay
list. Then resume keep running but the delayed urb have no chance
to be commit until next resume. If the time of next resume is far
away, tty will be blocked in tty_wait_until_sent during time. The
race also can lead to writes being reordered.
This patch put play_Delayed and intfdata->suspended together in the
spinlock, it's to avoid the write race during resume.
Fixes: 383cedc3bb ("USB: serial: full autosuspend support for the
option driver")
Signed-off-by: xiao jin <jin.xiao@intel.com>
Signed-off-by: Zhang, Qi1 <qi1.zhang@intel.com>
Reviewed-by: David Cohen <david.a.cohen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v2.6.32
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When enable usb serial for modem data, sometimes the tty is blocked
in tty_wait_until_sent because portdata->out_busy always is set and
have no chance to be cleared.
We find a bug in write error path. usb_wwan_write set portdata->out_busy
firstly, then try autopm async with error. No out urb submit and no
usb_wwan_outdat_callback to this write, portdata->out_busy can't be
cleared.
This patch clear portdata->out_busy if usb_wwan_write try autopm async
with error.
Fixes: 383cedc3bb ("USB: serial: full autosuspend support for the
option driver")
Signed-off-by: xiao jin <jin.xiao@intel.com>
Signed-off-by: Zhang, Qi1 <qi1.zhang@intel.com>
Reviewed-by: David Cohen <david.a.cohen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v2.6.32
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should call usb_mark_last_busy in all input paths, including the
interrupt completion handler.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The option line-control request has been using the wrong pipe direction,
while relying on USB core to fix it up.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix potential I/O while runtime suspended due to missing PM operations
in send_setup.
Fixes: 383cedc3bb ("USB: serial: full autosuspend support for the
option driver")
Cc: <stable@vger.kernel.org> # v2.6.32
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use tty-port initialised flag rather than private flag to determine when
port is closing down.
Since the tty-port flag is set prior to dropping DTR/RTS (when HUPCL is
set) this avoid submitting the read urbs when resuming the interface in
dtr_rts() only to immediately kill them again in shutdown().
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move usb_autopm_get_interface_no_resume to the end of close(). This
makes the window during which suspend is prevented before the final put
in USB serial core slightly smaller.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor and clean up delayed-urb submission at resume.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up suspend() somewhat and make sure to always set the suspended
flag (although it's only used for runtime PM) in order to match
resume().
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use usb_get_serial_data() rather than accessing the private pointer
directly.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty-port implementation has already made sure that DTR/RTS have been
raised and lowered by calling dtr_rts so remove the redundant calls from
open and close.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not resume any I/O, including the delayed write queue, on closed
ports.
Note that this currently has no functional impact due to the
usb_autopm_get_interface() in close(), but that call is about to be
removed by a follow-up patch.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove no longer needed disconnected test from close, which is never
called post disconnect (and drivers must handle failed I/O during
disconnect anyway).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver does not implement set_termios so the operation can be left
unset (tty will do the tty_termios_copy_hw for us).
Note that the send_setup call is bogus as it really only sets DTR/RTS
to their current values.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus endpoint-address test which is never true.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sierra line-control request has been using the wrong pipe direction,
while relying on USB core to fix it up.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add error message to resume error path and make sure to also return an
error when failing to submit a cached write.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to stop all I/O, including any active write urbs, at shutdown.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix characters potentially being dropped at close due to missing
chars_in_buffer implementation.
Note that currently the write urbs are not even killed at close (will be
fixed separately), but this could still lead to dropped data since we
have lowered DTR/RTS.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that needs_remote_wake up is always set when there are open
ports.
Currently close() would unconditionally set needs_remote_wakeup to 0
even though there might still be open ports. This could lead to blocked
input and possibly dropped data on devices that do not support remote
wakeup (and which must therefore not be runtime suspended while open).
Add an open_ports counter (protected by the susp_lock) and only clear
needs_remote_wakeup when the last port is closed.
Fixes: e6929a9020 ("USB: support for autosuspend in sierra while
online")
Cc: <stable@vger.kernel.org> # v2.6.32
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The delayed-write queue was never emptied on disconnect, something which
would lead to leaked urbs and transfer buffers if the device is
disconnected before being runtime resumed due to a write.
Fixes: e6929a9020 ("USB: support for autosuspend in sierra while
online")
Cc: <stable@vger.kernel.org> # v2.6.32
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neither the transfer buffer or the urb itself were released in the
resume error path for delayed writes. Also on errors, the remainder of
the queue was not even processed, which leads to further urb and buffer
leaks.
The same error path also failed to balance the outstanding-urb counter,
something which results in degraded throughput or completely blocked
writes.
Fix this by releasing urb and buffer and balancing counters on errors,
and by always processing the whole queue even when submission of one urb
fails.
Fixes: e6929a9020 ("USB: support for autosuspend in sierra while
online")
Cc: <stable@vger.kernel.org> # v2.6.32
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix use after free or NULL-pointer dereference during suspend and
resume.
The port data may never have been allocated (port probe failed)
or may already have been released by port_remove (e.g. driver is
unloaded) when suspend and resume are called.
Fixes: e6929a9020 ("USB: support for autosuspend in sierra while
online")
Cc: <stable@vger.kernel.org> # v2.6.32
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix AA deadlock in open error path that would call close() and try to
grab the already held disc_mutex.
Fixes: b9a44bc19f ("sierra: driver urb handling improvements")
Cc: <stable@vger.kernel.org> # v2.6.31
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matching on interface numbers was not such a good idea
for multi-function serial devices after all. It is much
better do create well defined device layouts, allowing
a single match entry per device.
Remove this now unused code.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the "non Gobi" Qualcomm based devices handled by this
driver share a common standard Sierra Wireless specific
layout. Adding code specifically for this layout allow
us to reduce the number of match entries per device from
three to one.
This change will result in a penalty wrt stable backports,
but simplifies new Sierra device addtitions in the long
term.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preparing for more supported standard device layouts. Keeping
the matching macros unchanged to avoid breaking stable
backporting of new device additions.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a consistent style for all multiline comments.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan writes:
"The Dell drivers use the same configuration for PIDs:
81A2: Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card
81A3: Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card
81A4: Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card
81A8: Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card
81A9: Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card
These devices are all clearly Sierra devices, but are also definitely
Gobi-based. The A8 might be the MC7700/7710 and A9 is likely a MC7750.
>From DellGobi5kSetup.exe from the Dell drivers:
usbif0: serial/firmware loader?
usbif2: nmea
usbif3: modem/ppp
usbif8: net/QMI"
Cc: <stable@vger.kernel.org>
Reported-by: AceLan Kao <acelan.kao@canonical.com>
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A number of older CMOTech modems are based on Qualcomm
chips. The blacklisted interfaces are QMI/wwan.
Reported-by: Lars Melin <larsm17@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During firmware download the device expects memory addresses in
big-endian byte order. As the wIndex parameter which hold the address is
sent in little-endian byte order regardless of host byte order, we need
to use swab16 rather than cpu_to_be16.
Also make sure to handle the struct ti_i2c_desc size parameter which is
returned in little-endian byte order.
Reported-by: Ludovic Drolez <ldrolez@debian.org>
Tested-by: Ludovic Drolez <ldrolez@debian.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix driver new_id sysfs-attribute removal deadlock by making sure to
not hold any locks that the attribute operations grab when removing the
attribute.
Specifically, usb_serial_deregister holds the table mutex when
deregistering the driver, which includes removing the new_id attribute.
This can lead to a deadlock as writing to new_id increments the
attribute's active count before trying to grab the same mutex in
usb_serial_probe.
The deadlock can easily be triggered by inserting a sleep in
usb_serial_deregister and writing the id of an unbound device to new_id
during module unload.
As the table mutex (in this case) is used to prevent subdriver unload
during probe, it should be sufficient to only hold the lock while
manipulating the usb-serial driver list during deregister. A racing
probe will then either fail to find a matching subdriver or fail to get
the corresponding module reference.
Since v3.15-rc1 this also triggers the following lockdep warning:
======================================================
[ INFO: possible circular locking dependency detected ]
3.15.0-rc2 #123 Tainted: G W
-------------------------------------------------------
modprobe/190 is trying to acquire lock:
(s_active#4){++++.+}, at: [<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94
but task is already holding lock:
(table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (table_lock){+.+.+.}:
[<c0075f84>] __lock_acquire+0x1694/0x1ce4
[<c0076de8>] lock_acquire+0xb4/0x154
[<c03af3cc>] _raw_spin_lock+0x4c/0x5c
[<c02bbc24>] usb_store_new_id+0x14c/0x1ac
[<bf007eb4>] new_id_store+0x68/0x70 [usbserial]
[<c025f568>] drv_attr_store+0x30/0x3c
[<c01690e0>] sysfs_kf_write+0x5c/0x60
[<c01682c0>] kernfs_fop_write+0xd4/0x194
[<c010881c>] vfs_write+0xbc/0x198
[<c0108e4c>] SyS_write+0x4c/0xa0
[<c000f880>] ret_fast_syscall+0x0/0x48
-> #0 (s_active#4){++++.+}:
[<c03a7a28>] print_circular_bug+0x68/0x2f8
[<c0076218>] __lock_acquire+0x1928/0x1ce4
[<c0076de8>] lock_acquire+0xb4/0x154
[<c0166b70>] __kernfs_remove+0x254/0x310
[<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94
[<c0169fb8>] remove_files.isra.1+0x48/0x84
[<c016a2fc>] sysfs_remove_group+0x58/0xac
[<c016a414>] sysfs_remove_groups+0x34/0x44
[<c02623b8>] driver_remove_groups+0x1c/0x20
[<c0260e9c>] bus_remove_driver+0x3c/0xe4
[<c026235c>] driver_unregister+0x38/0x58
[<bf007fb4>] usb_serial_bus_deregister+0x84/0x88 [usbserial]
[<bf004db4>] usb_serial_deregister+0x6c/0x78 [usbserial]
[<bf005330>] usb_serial_deregister_drivers+0x2c/0x4c [usbserial]
[<bf016618>] usb_serial_module_exit+0x14/0x1c [sierra]
[<c009d6cc>] SyS_delete_module+0x184/0x210
[<c000f880>] ret_fast_syscall+0x0/0x48
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(table_lock);
lock(s_active#4);
lock(table_lock);
lock(s_active#4);
*** DEADLOCK ***
1 lock held by modprobe/190:
#0: (table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial]
stack backtrace:
CPU: 0 PID: 190 Comm: modprobe Tainted: G W 3.15.0-rc2 #123
[<c0015e10>] (unwind_backtrace) from [<c0013728>] (show_stack+0x20/0x24)
[<c0013728>] (show_stack) from [<c03a9a54>] (dump_stack+0x24/0x28)
[<c03a9a54>] (dump_stack) from [<c03a7cac>] (print_circular_bug+0x2ec/0x2f8)
[<c03a7cac>] (print_circular_bug) from [<c0076218>] (__lock_acquire+0x1928/0x1ce4)
[<c0076218>] (__lock_acquire) from [<c0076de8>] (lock_acquire+0xb4/0x154)
[<c0076de8>] (lock_acquire) from [<c0166b70>] (__kernfs_remove+0x254/0x310)
[<c0166b70>] (__kernfs_remove) from [<c0167aa0>] (kernfs_remove_by_name_ns+0x4c/0x94)
[<c0167aa0>] (kernfs_remove_by_name_ns) from [<c0169fb8>] (remove_files.isra.1+0x48/0x84)
[<c0169fb8>] (remove_files.isra.1) from [<c016a2fc>] (sysfs_remove_group+0x58/0xac)
[<c016a2fc>] (sysfs_remove_group) from [<c016a414>] (sysfs_remove_groups+0x34/0x44)
[<c016a414>] (sysfs_remove_groups) from [<c02623b8>] (driver_remove_groups+0x1c/0x20)
[<c02623b8>] (driver_remove_groups) from [<c0260e9c>] (bus_remove_driver+0x3c/0xe4)
[<c0260e9c>] (bus_remove_driver) from [<c026235c>] (driver_unregister+0x38/0x58)
[<c026235c>] (driver_unregister) from [<bf007fb4>] (usb_serial_bus_deregister+0x84/0x88 [usbserial])
[<bf007fb4>] (usb_serial_bus_deregister [usbserial]) from [<bf004db4>] (usb_serial_deregister+0x6c/0x78 [usbserial])
[<bf004db4>] (usb_serial_deregister [usbserial]) from [<bf005330>] (usb_serial_deregister_drivers+0x2c/0x4c [usbserial])
[<bf005330>] (usb_serial_deregister_drivers [usbserial]) from [<bf016618>] (usb_serial_module_exit+0x14/0x1c [sierra])
[<bf016618>] (usb_serial_module_exit [sierra]) from [<c009d6cc>] (SyS_delete_module+0x184/0x210)
[<c009d6cc>] (SyS_delete_module) from [<c000f880>] (ret_fast_syscall+0x0/0x48)
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit 8e493ca176 ("USB: usb_wwan: fix
bulk-urb allocation") by making sure to require both bulk-in and out
endpoints during port probe.
The original option driver (which usb_wwan is based on) was written
under the assumption that either endpoint could be missing, but
evidently this cannot have been tested properly. Specifically, it would
handle opening a device without bulk-in (but would blow up during resume
which was implemented later), but not a missing bulk-out in write()
(although it is handled in some places such as write_room()).
Fortunately (?), the driver also got the test for missing endpoints
wrong so the urbs were in fact always allocated, although they would be
initialised using the wrong endpoint address (0) and any submission of
such an urb would fail.
The commit mentioned above fixed the test for missing endpoints but
thereby exposed the other bugs which would now generate null-pointer
exceptions rather than failed urb submissions.
The regression was introduced in v3.7, but the offending commit was also
marked for stable.
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 1ebca9dad5.
This device was erroneously added to the sierra driver even though it's
not a Sierra device and was already handled by the option driver.
Cc: Richard Farina <sidhayn@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing newlines to dev_<level> messages.
Also make some messages less verbose where appropriate.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Add missing braces to conditional branches and one loop in usb-serial
core and generic implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Do not discard buffered data and make sure to try to resubmit the write
urbs on errors.
Currently a recoverable error would lead to more data than necessary
being dropped.
Also upgrade error messages from debug to error log level.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Make sure to try to resubmit the read urb on errors.
Currently a recoverable error would lead to reduced throughput as only
one urb will be used until the port is closed and reopened (or
resumed or unthrottled).
Also upgrade error messages from debug to error log level.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Drivers are allowed to override the default bulk-out buffer size
(endpoint maximum packet size) in order to increase throughput, but it
does not make much sense to allow buffers smaller than the default.
Note that this is already how bulk_in_size is defined.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Remove erroneous call to usb_clear_halt which is blocking and cannot be
used in interrupt context.
This code has possibly never been executed as it would cause an oops if
it was. Simply treat a stalled-endpoint error as any other error
condition.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Hello,
the following patch adds an entry for the PID of a Cressi Leonardo
diving computer interface to kernel 3.13.0.
It is detected as FT232RL.
Works with subsurface.
Signed-off-by: Joerg Dorchain <joerg@dorchain.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This interface is to be handled by the qmi_wwan driver.
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interface #5 of 19d2:1270 is a net interface which has been submitted to the
qmi_wwan driver so consequently remove it from the option driver.
Signed-off-by: Raymond Wanyoike <raymond.wanyoike@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding two more IDs to the ftdi_sio usb serial driver.
It now connects Tagsys RFID readers.
There might be more IDs out there for other Tagsys models.
Signed-off-by: Ulrich Hahn <uhahn@eanco.de>
Cc: Johan Hovold <johan@hovold.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device was mentioned in an OpenWRT forum. Seems to have a "standard"
Sierra Wireless ifnumber to function layout:
0: qcdm
2: nmea
3: modem
8: qmi
9: storage
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for ANT USB-m Stick from Dynastream Innovations, by listing
USB pid
[34366.944805] usb 6-1: New USB device found, idVendor=0fcf, idProduct=1009
[34366.944817] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[34366.944824] usb 6-1: Product: ANT USB-m Stick
[34366.944831] usb 6-1: Manufacturer: Dynastream Innovations
Device reported (https://code.google.com/p/antpm/issues/detail?id=5) to
work through:
$ modprobe usbserial vendor=0x0fcf product=0x1009
Signed-off-by: Kristóf Ralovich <kristof.ralovich@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
Often, usb drivers need some driver_info to get a device to work. To
have access to driver_info when using new_id, allow to pass a reference
vendor:product tuple from which new_id will inherit driver_info.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Genuine FTDI chips support only CS7/8. A previous fix in commit
8704211f65 ("USB: ftdi_sio: fixed handling of unsupported CSIZE
setting") enforced this limitation and reported it back to userspace.
However, certain types of smartcard readers depend on specific
driver behaviour that requests 0 data bits (not 5) to change into a
different operating mode if CS5 has been set.
This patch reenables this behaviour for all FTDI devices.
Tagged to be added to stable, because it affects a lot of users of
embedded systems which rely on these readers to work properly.
Cc: stable <stable@vger.kernel.org>
Reported-by: Heinrich Siebmanns <H.Siebmanns@t-online.de>
Tested-by: Heinrich Siebmanns <H.Siebmanns@t-online.de>
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixed several typo in printk from various
part of kernel source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Switch to the generic TIOCMIWAIT implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only wake up MSR wait queue on actual modem-status changes.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation which does not suffer
from the races involved when using the deprecated sleep_on functions.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only wake up MSR wait queue on actual modem-status changes.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the TIOCMIWAIT mask is always honoured.
The CH341 interrupt status has a multiple-status changed flag which
indicates that multiple status changes has occurred since last interrupt
event. Unfortunately, if the final status is the same, there appears to
be no way to determine which signal(s) has changed (an even number of
times).
This means that the multiple-status flag should not be used in
TIOCMIWAIT as it leads to the signal mask argument being ignored (e.g.
TIOCMIWAIT could return if DSR changes twice, even though the user only
cares about carrier changes).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
