* master.kernel.org:/pub/scm/linux/kernel/git/paulus/powerpc: (116 commits)
[POWERPC] Add export of vgacon_remap_base
[POWERPC] Remove bogus comment about page_is_ram
[POWERPC] windfarm: don't die on suspend thread signal
[POWERPC] Fix comment in kernel/irq.c
[POWERPC] ppc: Fix booke watchdog initialization
[POWERPC] PPC: Use ARRAY_SIZE macro when appropriate
[POWERPC] Use ARRAY_SIZE macro when appropriate
[POWERPC] Fix ppc64's writing to struct file_operations
[POWERPC] ppc: use syslog macro for the printk log level
[POWERPC] ppc: cs4218_tdm remove extra brace
[POWERPC] Add mpc52xx/lite5200 PCI support
[POWERPC] Only use H_BULK_REMOVE if the firmware supports it
[POWERPC] Fixup error handling when emulating a floating point instruction
[POWERPC] Enable interrupts if we are doing fp math emulation
[POWERPC] Added kprobes support to ppc32
[POWERPC] Make pSeries use the H_BULK_REMOVE hypervisor call
[POWERPC] Clear RI bit in MSR before restoring r13 when returning to userspace
[POWERPC] Fix performance monitor exception
[POWERPC] Compile fixes for arch/powerpc dcr code
[POWERPC] Maple: use mmio nvram
...
The following macro :
include/asm-powerpc/vga.h:#define VGA_MAP_MEM(x,s) (x + vgacon_remap_base)
is used by drivers/video/console/vgacon.c which can be compiled as a module
(drivers/video/vga16fb.ko).
Therefore, vgacon_remap_base should be exported.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/mm/mem.c states that page_is_ram is called by the code that
implements /dev/mem, which isn't true. Remove the comment.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
kernel/irq.c contains a comment that speaks of -1 and -2 as interrupt
numbers, but this is actually dependent on configuration options now.
Replace by NO_IRQ and NO_IRQ_ENABLED.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use ARRAY_SIZE macro already defined in linux/kernel.h
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In preparation for marking file_operations as const.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The previous patch changing pSeries to use H_BULK_REMOVE broke the
JS20 blade, where the firmware doesn't support H_BULK_REMOVE. This
adds a firmware check so that on machines that don't have H_BULK_REMOVE,
we just use the H_REMOVE call as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
pci_scan_msi_device() doesn't do anything anymore, so remove it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB OHCI driver bus glue for the PS3 game console.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB EHCI driver bus glue for the PS3 game console.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we do full FP emulation its possible that we need to post a SIGFPE based
on the results of the emulation. The previous code ignored this case completely.
Additionally, the Soft_emulate_8xx case had two issues. One, we should never
generate a SIGFPE since the code only does data movement. Second, we were
interpreting the return codes incorrectly, it returns 0 on success, 1 on
illop and -EFAULT on a data access error.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Anytime we are emulating an instruction we are going to be doing some form of
get_user() to get the instruction image to decode. Since get_user() might
sleep we need to ensure we have interrupts enabled or we might see something
like:
Debug: sleeping function called from invalid context at arch/powerpc/kernel/traps.c:697
in_atomic():0, irqs_disabled():1
Call Trace:
[D6023EB0] [C0007F84] show_stack+0x58/0x174 (unreliable)
[D6023EE0] [C0022C34] __might_sleep+0xbc/0xd0
[D6023EF0] [C000D158] program_check_exception+0x1d8/0x4fc
[D6023F40] [C000E744] ret_from_except_full+0x0/0x4c
--- Exception: 700 at 0x102a7100
LR = 0xdb9ef04
However, we want to ensure that interrupts are disabled when handling a trap
exception that might be used for a kernel breakpoint. This is why ProgramCheck
is marked as EXC_XFER_STD instead of EXC_XFER_EE.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added kprobes to ppc32 platforms that have use single_step_exception. This
excludes 4xx and anything Book-E since their debug mechanisms for single stepping
are completely different.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
H_BULK_REMOVE lets us remove 4 entries from the MMU hash table with one
hypervisor call. This uses it in pSeries_lpar_hpte_invalidate so we
can tear down mappings with fewer hypervisor calls.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some instruction tracing tools use the RI (recoverable interrupt) bit
in the MSR to indicate when it's safe to single-step. Currently we
clear RI after restoring r13 when returning to userspace. However,
if we single-step past the point where r13 is restored, we'll corrupt
r13 in the exception entry code and not restore it. This moves the
clearing of RI to just before r13 is restored so this doesn't happen.
Signed-off-by: Paul Mackerras <paulus@samba.org>
To the issue: some point during 2.6.20 development, Paul Mackerras
introduced the "lazy IRQ disabling" patch (very cool work, BTW).
In that patch, the performance monitor unit exception was marked as
"maskable", in the sense that if interrupts were soft-disabled, that
exception could be ignored. This broke my PowerPC profiling code.
The symptom that I see is that a varying number of interrupts
(from 0 to $n$, typically closer to 0) get delivered, when, in
reality, it should always be very close to $n$.
The issue stems from the way masking is being done. Masking in
this fashion seems to work well with the decrementer and external
interrupts, because they are raised again until "really" handled.
For the PMU, however, this does not apply (at least on my Xserver
machine with a 970FX processor). If the PMU exception is not handled,
it will _not_ be re-raised (at least on my machine). The documentation
states that the PMXE bit in MMCR0 is set to 0 when the PMU exception
is raised. However, software must re-set the bit to re-enable PMU
exceptions. If the exception is ignored (as currently) not only is
that interrupt lost, but because software does not re-set PMXE, the
PMU registers are "frozen" forever.
[This patch means that performance monitor exceptions are taken and
handled even if irqs are off, as long as some other interrupt hasn't
come along and caused interrupts to be hard-disabled. In this sense
the PMU exception becomes like an NMI. The oprofile code for most
powerpc processors does nothing that is unsafe in an NMI context, but
the Cell oprofile code does a spin_lock_irqsave. However, that turns
out to be OK because Cell doesn't actually use the performance
monitor exception; performance monitor interrupts come in as a
regular interrupt on Cell, so will be disabled when irqs are off.
-- paulus.]
Signed-off-by: Paul Mackerras <paulus@samba.org>
The new dcr code does not currently compile when configured for native
DCR access on ARCH=powerpc. This patch fixes the problems.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some systems supported by the maple platform (e.g. JS2x blades running
SLOF) are able to use the mmio_nvram backend for reading and writing
nvram. This is an improvement over the current situation -- no nvram
access from userspace at all.
Select MMIO_NVRAM for the maple platform.
Initialize the mmio_nvram backend from maple setup code.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Base pasemi defconfig. Nothing special, just the native drivers plus
common PCI-express/PCI cards.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The DMA controller on PWRficient is somewhat special -- has a PCI header
so it looks like it's on the root PCI (-Express) root bus, but it uses
more than the default number of interrupts (and they are hardwired).
We need to wire up all interrupts for the DMA controller. The generic
IRQ code will only map the primary interrupt from the PCI header (128),
so add 129->211 by hand.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Timebase update is simple on PA6T, since global updates can be done from
one core by writing to an SPR.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement reset on platforms/pasemi. Default is just to reset the
cpu using the SDC registers.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Powersave support on PA6T. Right now it only uses 'doze' mode, and
will default to no savings (spin).
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Early debug output for PA Semi UART. Uses the 2.05 CI real mode ops.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
G3 Blue & White is misconfigured by default so that CardBus controllers
in PCI slots don't work. The PCI bridge is programmed to only allow
access to bus 1 but not higher busses.
The patch forces the PCI busses to be reassigned if a Grackle controller
is found and the machine identifies itself as "PowerMac1,1"
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds base support for Celleb platform.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Spu management ops in arch/platforms/cell/spu_priv1_mmio.h can be used
commonly in of based platform. This patch separates spu management ops
from native cell code and uses on celleb platform.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds udbg support for Celleb platform.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch creates Celleb platform dependent file to support iommu.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
USB host controller in SCC requires enable sequence. It should be done
before USB host drivers start.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Default config file for mpc8272ads (powerpc port).Though relevant bits went
in, it is required to keep proper default configuration for the target,
which seems to be missed initially.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Recent update of asm-powerpc/io.h caused cpm-related stuff to break in the
current kernel. Current patch fixes it, as well as other inconsistencies
expressed, that do not permit targets from working properly:
- Updated dts with a chosen node with interrupt controller,
- fixed messed device IDs among CPM2 SoC devices,
- corrected odd header name and fixed type in defines,
- Added 82xx subdir to the powerpc/platforms Makefile, missed during
initial commit,
- new solely-powerpc header file for 8260 family (was using one from
arch/ppc, this one cleaned up from the extra stuff), in fact for now
a placeholder to get the board-specific includes for stuff not yet
capable to live with devicetree peeks only
- Fixed couple of misprints in reference mpc8272 dts.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This contains important fixes for the CPM2 PIC code. Eliminated
CPM_IRQ_OFFSET, pulling the respective interrupt numbers from the interrupt
mapping. Updated devicetree files to reflect that. Changed direct
IC-related IO accesses to the IO accessors. Fixed all the sense values to
keep coherency with ipic. In the current code, CPM2 stuff will have no IRQs
and hence could be hardly usable.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update ps3_defconfig to enable USB mass storage and VFAT.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the missing pieces to support DMA scatter-gather on the PS3 system bus.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
