This patch extends the existing malicious driver operation detection
logic to cover malicious operations by the VF driver as well.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Post VF initialization, there are a couple of different ways in which a
VF reset can be triggered. One is when the underlying PF itself goes
through a reset and other is via a VFLR interrupt. ice_reset_vf introduced
in this patch handles both these cases.
Also introduced in this patch is a helper function ice_aq_send_msg_to_vf
to send messages to VF over the mailbox queue. The PF uses this to send
reset notifications to VFs.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Until now, all the VSI and queue management code supported only the PF
VSI type (ICE_VSI_PF). Update these flows to handle the VF VSI type
(ICE_VSI_VF) type as well.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements parts of ice_sriov_configure and VF reset flow.
To create virtual functions (VFs), the user sets a value in num_vfs
through sysfs. This results in the kernel calling the handler for
.sriov_configure which is ice_sriov_configure.
VF setup first starts with a VF reset, followed by allocation of the VF
VSI using ice_vf_vsi_setup. Once the VF setup is complete a state bit
ICE_VF_STATE_INIT is set in the vf->states bitmap to indicate that
the VF is ready to go.
Also for VF reset to go into effect, it's necessary to issue a disable
queue command (ice_aqc_opc_dis_txqs). So this patch updates multiple
functions in the disable queue flow to take additional parameters that
distinguish if queues are being disabled due to VF reset.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mailbox queue is a type of control queue that's used for communication
between PF and VF. This patch adds code to initialize, configure and
use mailbox queues.
This patch also adds support to detect and parse SR-IOV capabilities
returned by the hardware.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently there is no support for dynamic interrupt moderation. This
patch adds some initial code to support this. The following changes
were made:
1. Currently we are using multiple members to store the interrupt
granularity (itr_gran_25/50/100/200). This is not necessary because
we can query the device to determine what the interrupt granularity
should be set to, done by a new function ice_get_itr_intrl_gran.
2. Added intrl to ice_q_vector structure to support interrupt rate
limiting.
3. Added the function ice_intrl_usecs_to_reg for converting to a value
in usecs that the device understands.
4. Added call to write to the GLINT_RATE register. Disable intrl by
default for now.
5. Changed rx/tx_itr_setting to itr_setting because having both seems
redundant because a ring is either Tx or Rx.
6. Initialize itr_setting for both Tx/Rx rings in ice_vsi_alloc_rings()
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a malicious operation is detected, the firmware triggers an
interrupt, which is then picked up by the service task (specifically by
ice_handle_mdd_event). A reset is scheduled if required.
Tx hang detection works in a similar way, except the logic here monitors
the VSI's Tx queues and tries to revive them if stalled. If the hang is
not resolved, the kernel eventually calls ndo_tx_timeout, which is
handled by ice_tx_timeout.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the existing register definitions.
1) Several instances of long defines names used in the BIT() macro
were replaced to use the actual values they represent. As a
result some defines for shifts (ending with _S) that were used
only to create bitmasks were removed completely.
2) Apply more consistent tab spacing.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the following interrupt causes that are not applicable or not
handled:
- PFINT_OICR_HLP_RDY_M
- PFINT_OICR_CPM_RDY_M
- PFINT_OICR_GPIO_M
- PFINT_OICR_STORM_DETECT_M
Add the following interrupt cause that's actually handled in ice_misc_intr:
- PFINT_OICR_PE_CRITERR_M
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the hardware spec, checking the INTEVENT bit isn't a
reliable way to detect if an OICR interrupt has occurred. This is
because this bit can be cleared by the hardware/firmware before the
interrupt service routine has run. So instead, just check for OICR
events every time.
Fixes: 940b61af02 ("ice: Initialize PF and setup miscellaneous interrupt")
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Link events are posted to a PF's admin receive queue (ARQ). This patch
adds the ability to detect and process link events.
This patch also adds the ability to process resets.
The driver can process the following resets:
1) EMP Reset (EMPR)
2) Global Reset (GLOBR)
3) Core Reset (CORER)
4) Physical Function Reset (PFR)
EMPR is the largest level of reset that the driver can handle. An EMPR
resets the manageability block and also the data path, including PHY and
link for all the PFs. The affected PFs are notified of this event through
a miscellaneous interrupt.
GLOBR is a subset of EMPR. It does everything EMPR does except that it
doesn't reset the manageability block.
CORER is a subset of GLOBR. It does everything GLOBR does but doesn't
reset PHY and link.
PFR is a subset of CORER and affects only the given physical function.
In other words, PFR can be thought of as a CORER for a single PF. Since
only the issuing PF is affected, a PFR doesn't result in the miscellaneous
interrupt being triggered.
All the resets have the following in common:
1) Tx/Rx is halted and all queues are stopped.
2) All the VSIs and filters programmed for the PF are lost and have to be
reprogrammed.
3) Control queue interfaces are reset and have to be reprogrammed.
In the rebuild flow, control queues are reinitialized, VSIs are reallocated
and filters are restored.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch configures the VSIs to be able to send and receive
packets by doing the following:
1) Initialize flexible parser to extract and include certain
fields in the Rx descriptor.
2) Add Tx queues by programming the Tx queue context (implemented in
ice_vsi_cfg_txqs). Note that adding the queues also enables (starts)
the queues.
3) Add Rx queues by programming Rx queue context (implemented in
ice_vsi_cfg_rxqs). Note that this only adds queues but doesn't start
them. The rings will be started by calling ice_vsi_start_rx_rings on
interface up.
4) Configure interrupts for VSI queues.
5) Implement ice_open and ice_stop.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch continues the initialization flow as follows:
1) Allocate and initialize necessary fields (like vsi, num_alloc_vsi,
irq_tracker, etc) in the ice_pf instance.
2) Setup the miscellaneous interrupt handler. This also known as the
"other interrupt causes" (OIC) handler and is used to handle non
hotpath interrupts (like control queue events, link events,
exceptions, etc.
3) Implement a background task to process admin queue receive (ARQ)
events received by the driver.
CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements multiple pieces of the initialization flow
as follows:
1) A reset is issued to ensure a clean device state, followed
by initialization of admin queue interface.
2) Once the admin queue interface is up, clear the PF config
and transition the device to non-PXE mode.
3) Get the NVM configuration stored in the device's non-volatile
memory (NVM) using ice_init_nvm.
CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A control queue is a hardware interface which is used by the driver
to interact with other subsystems (like firmware, PHY, etc.). It is
implemented as a producer-consumer ring. More specifically, an
"admin queue" is a type of control queue used to interact with the
firmware.
This patch introduces data structures and functions to initialize
and teardown control/admin queues. Once the admin queue is initialized,
the driver uses it to get the firmware version.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
