sdhci_add_host() allows the Host Controller Capability registers
to be supplied by the calling driver by using
SDHCI_QUIRK_MISSING_CAPS, but the check for the Capabilities bit
SDHCI_CAN_64BIT doesn't use the applied value and instead reads
the Host register directly. This change uses the supplied "caps"
register instead of reading the host register.
This change will allow a calling driver to simply clear the
SDHCI_CAN_64BIT bit in "caps" to handle some cases of
SDHCI_QUIRK2_BROKEN_64_BIT_DMA.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver supports the SDHCI host controller found on a PIC32.
Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
This patch make num_slots to 1 if pdata->num_slot is not
defined. Meanwhile, we need to make sure num_slots should
not larger that the supported slots
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_probe clear interrupts and disable all interrupts firstly.
While it clear interrupt again before enable some interrupts. We
can't see any reason to clear it twice here, so remove the second one.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mmc already use mmc_of_parse to get "broken-cd" property,
but it considered "broken-cd" to be a quirk in its driver. We
don't need this quirk here, and just take what we need from
mmc->caps.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch implement hw_reset function for DesignWare
MMC controller. By adding this feature, mmc blk can
do some basic recovery.
Set the following resets:
software reset – BMOD[0] for IDMAC only
DMA reset - CTRL[2]
FIFO reset - CTRL[1] bits
Program the CARD_RESET register with a value of 0 for the bit
corresponding to the card number; This programming asserts the
RST_n signal and resets the card. After a minimum of 1 ?s, de-asserts the
RST_n signal and takes the card out of reset. The application can program
a new CMD only after a minimum of 200 us
This implementation can be easily tested by cutting off->On vmmc
while doing data accessing in background to simulate that case.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch removes the prepare_command hook from entire dw_mmc driver.
Now, almost all SoCs are using by default, except Exynos.
It seems that dwmmc controller is using unnecessary hook.
To know whether needs to set this bit or not,
add the DW_MMC_CARD_NO_USE_HOLD bit.
If some SoCs need to disable this in future, just set the
DW_MMC_CARD_NO_USE_HOLD bit.
set_bit(DW_MMC_CARD_NO_USE_HOLD, &slot->flags),
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Print the error code when the tuning command fails. This allows the
reason for the failure to be reported, which aids debugging.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Re-tuning is part of standard requirements for the higher speed SD
card protocols, and is not an error when this occurs. When we retry
a command due to a retune, we should not print a message to the
kernel log.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Improve mmc_of_parse_voltage()'s return values so that drivers can tell
whether a voltage-range specification was present, and whether it has
been successfully parsed, or there was an error while parsing.
We return a negative errno when parsing fails, zero if no voltage-range
specification is present, or one if a voltage-range specification is
successfully parsed.
No users need modifying as no users check the return value.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Each time a driver such as sdhci-esdhc-imx is probed, we get a info
printk complaining that the DT voltage-ranges property has not been
specified.
However, the DT binding specifically says that the voltage-ranges
property is optional. That means we should not be complaining that
DT hasn't specified this property: by indicating that it's optional,
it is valid not to have the property in DT.
Silence the warning if the property is missing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rcar2 & 3 docs state that for going to and coming from the 0xff setting,
the clock must first be disabled before the DIV bits are changed.
Instead of tracking this, let's just do this unconditionally.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some of the indentation made the code awful to read. Fix that. Also,
introduce defines instead of magic hex values. Note that this includes
one change: We mask out know 0xff instead of 0x1ff. But 0x100 has always
been the clock enable bit. It doesn't make any sense to set it depending
on the clock calculation. Update copyright notices, too. I'll be working
on those files some more in the future.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These don't make sense anymore. Since commit 5d60e50054 ("mmc: tmio:
add new TMIO_MMC_HAVE_HIGH_REG flags"), we don't deal with a resource
here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The docs for RCar Gen2 & 3 I have access to, mention delays of 5ms after
stop and 1ms after start. Make it possible to apply these values.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All the docs I have access to say that this register needs the bus busy
check.
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When compiling the driver with CONFIG_MMC_DEBUG set, I got build
warnings. They have been 'fixed' meanwhile. However, because these debug
messages look random anyhow (some duplicate information printed etc),
let's just drop them and rather re-add something consistent if that
should ever be needed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After removed the MMC_DATA_STREAM, only two flags are remained.
(MMC_DATA_READ and MMC_DATA_WRITE)
The flags of READ and WRITE can't be used together.
That's why it doesn't need to use "OR' operation.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that clock delay settings for 8 bit DDR are correct, and vqmmc
support is available, we can enable MMC_CAP_1_8V_DDR support. This
enables MMC HS-DDR at up to 52 MHz, even if signal voltage switching
is not available.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allwinner's MMC controller needs to run at double the card clock rate
for 8 bit DDR transfer modes. Interestingly, this is not needed for
4 bit DDR transfers.
Different clock delays are needed for 8 bit eMMC DDR, due to the
increased module clock rate. For the A80 though, the same values for
4 bit and 8 bit are shared. The new values for the other SoCs were from
A83T user manual's "new timing mode" default values, which describes
them in clock phase, rather than delay periods. These values were used
without any modification. They may not be correct, but they work.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DDR transfer modes include UHS-1 DDR50 and MMC HS-DDR (or MMC_DDR52).
Consider MMC_DDR52 when setting clock delays.
Since MMC high speed mode goes up to 52 MHz instead of 50 MHz for SD,
and this number is visible in the capability macro, increase the
clock rate upper limit to 52 MHz.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bus width is sometimes the actual bus width, and sometimes indices
to different arrays encoding the bus width. In my debugging case "2"
could mean 8-bit as well as 4-bit, which was extremly confusing. Let's
use the human-readable actual bus width in all places.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In linux/mmc/host.h, mmc_card_is_removable() is already defined.
There is no reason that it doesn't use.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_iproc_remove() is jsut a wrapper to sdhci_pltfm_unregister.
So use the sdhci_pltfm_unregister() for the .remove hook directly.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Scott Branden from Broadcom said that the BCM2835 eMMC IP core is
very similar to IPROC and share most of the quirks. So use this driver
instead of separate one.
The sdhci-iproc contains a better workaround for the clock domain
crossing problem which doesn't need any delays. This results in a
better write performance.
Btw we get the rid of the SDHCI_CAPABILITIES hack in the sdhci_readl
function.
Suggested-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch moves the definition of the MMC capabilities
from the probe function into iproc platform data. After
that we are able to add support for another platform more
easily.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Suggested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I had to use the source to determine what I need to write to 'test' so
that all tests are run. Let's mention this explicitly in 'testlist'.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I don't see a reason why a host driver should depend on the card driver.
It also prevents that we can use the mmc_test driver. So, remove it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
IMO this info is only useful for developers. Most users won't need this
information, since there is not much they can do about it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When DT based probing is used but the DMA request fails, the
driver will print uninitialized stack data from the rx_req
and tx_req variables, as indicated by this warning:
drivers/mmc/host/omap_hsmmc.c: In function 'omap_hsmmc_probe':
drivers/mmc/host/omap_hsmmc.c:2162:3: warning: 'rx_req' may be used uninitialized in this function [-Wmaybe-uninitialized]
dev_err(mmc_dev(host->mmc), "unable to obtain RX DMA engine channel %u\n", rx_req);
This removes the DMA request line number from the warning, which
is the easiest solution and won't hurt us any more as we are
planning to remove the legacy code path anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch enables sdhci-acpi devices to suspend/resume asynchronously.
This will improve system suspend/resume speed. After enabling the
sdhci-acpi devices and all their child devices to suspend/resume
asynchronously on ASUS T100TA, the system suspend-to-idle time is
reduced from 1645ms to 1089ms, and the system resume time is reduced
from 940ms to 908ms.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch enables mmc hosts to suspend/resume asynchronously.
This will improve system suspend/resume speed. After applying
this patch and enabling all mmc hosts' child devices to
suspend/resume asynchronously on ASUS T100TA, the system
suspend-to-idle time is reduced from 1645ms to 1107ms, and the
system resume time is reduced from 940ms to 914ms.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eMMC chips require 2 power supplies, vmmc for internal logic, and vqmmc
for driving output buffers. vqmmc also controls signaling voltage. Most
boards we've seen use the same regulator for both, nevertheless the 2
have different usages, and should be set separately.
This patch adds support for vqmmc regulator supply, including voltage
switching. The MMC core can use this to try different signaling voltages
for eMMC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let .set_ios() fail if mmc_regulator_set_ocr() fails to enable and set a
proper voltage for vmmc.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sunxi_mmc_init_host() originated from Allwinner kernel sources. The
magic numbers written to various registers was never documented.
Add comments for values found in Allwinner user manuals.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The RPi firmware-based clocks driver can actually disable
unused clocks, so when switching to use it we ended up losing
our MMC clock once all devices were probed.
This patch adopts the changes from 1e5a0a9a58 ("mmc: sdhci-bcm2835:
Actually enable the clock") to sdhci-iproc.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clock frequency values written to an mmc host should not be less than
the minimum clock frequency which the mmc host supports.
Signed-off-by: Yuan Juntao <juntaox.yuan@intel.com>
Signed-off-by: Pawel Wodkowski <pawelx.wodkowski@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adopts the changes from 475c9e43bf ("mmc: sdhci-bcm2835:
Clean up platform allocations if sdhci init fails") to sdhci-iproc.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Arason SD host controller supports set block count command (cmd23)
and high speed mode. This patch re-enable both of these features that
was disabled. For device that doesn't support high speed, it should
configure its capability register accordingly instead disables it
explicitly.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since v4.3+, CONFIG_REGULATOR_PBIAS should be enabled (for platforms that
have PBIAS regulator) in order for MMC1 to work.
Add a more verbose print to help enable CONFIG_REGULATOR_PBIAS for users
using a olddefconfig or a custom .config.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Variable assignment just before return is redundant.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This issue was detected by using the Coccinelle software.
Two pointer checks could be repeated by the sdricoh_init_mmc() function
during error handling even if the relevant properties can be determined
for the involved variables before by source code analysis.
* This implementation detail could be improved by adjustments
for jump targets according to the Linux coding style convention.
* Drop an unnecessary initialisation for the variable "mmc" then.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These variables will eventually be set to an appropriate value a bit later.
* host
* iobase
* result
Thus let us omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind") introduced pm_runtime_reinit() that is used
to reinitialize PM runtime after -EPROBE_DEFER. This allows shutting
down the device after a failed probe.
However, for drivers using pm_runtime_use_autosuspend() this can cause
a state where suspend callback is never called after -EPROBE_DEFER.
On the following device driver probe, hardware state is different from
the PM runtime state causing omap_device to produce the following
error:
omap_device_enable() called from invalid state 1
And with omap_device and omap hardware being picky for PM, this will
block any deeper idle states in hardware.
The solution is to fix the drivers to follow the PM runtime documentation:
1. For sections of code that needs the device disabled, use
pm_runtime_put_sync_suspend() if pm_runtime_set_autosuspend() has
been set.
2. For driver exit code, use pm_runtime_dont_use_autosuspend() before
pm_runtime_put_sync() if pm_runtime_use_autosuspend() has been
set.
Fixes: 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind")
Cc: linux-mmc@vger.kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 829b6962f7.
Revert this change as it causes a sysfs path to change and therefore
introduces and ABI regression. More precisely Android's vold is not being
able to access /sys/module/mmcblk/parameters/perdev_minors any more, since
the path becomes changed to: "/sys/module/mmc_block/..."
Fixes: 829b6962f7 ("mmc: block: don't use parameter prefix if built as
module")
Reported-by: John Stultz <john.stultz@linaro.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel BXT/APL use a card detect GPIO however the host controller
will not enable bus power unless it's card detect also reflects
the presence of a card. Unfortunately those 2 things race which
can result in commands not starting, after which the controller
does nothing and there is a 10 second wait for the driver's
10-second timer to timeout.
That is fixed by having the driver look also at the present state
register to determine if the card is present. Consequently, provide
a 'get_cd' mmc host operation for BXT/APL that does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel BXT/APL use a card detect GPIO however the host controller
will not enable bus power unless it's card detect also reflects
the presence of a card. Unfortunately those 2 things race which
can result in commands not starting, after which the controller
does nothing and there is a 10 second wait for the driver's
10-second timer to timeout.
That is fixed by having the driver look also at the present state
register to determine if the card is present. Consequently, provide
a 'get_cd' mmc host operation for BXT/APL that does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers may need to provide their own get_cd() mmc host op, but
currently the internals of the current op (sdhci_get_cd()) are
provided by sdhci_do_get_cd() which is also called from
sdhci_request().
To allow override of the get_cd functionality, change sdhci_request()
to call ->get_cd() instead of sdhci_do_get_cd().
Note, in the future the call to ->get_cd() will likely be removed
from sdhci_request() since most drivers don't need actually it.
However this change is being done now to facilitate a subsequent
bug fix.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the past, fixes for specific hardware devices were implemented
in sdhci using quirks. That approach is no longer accepted because
the growing number of quirks was starting to make the code difficult
to understand and maintain.
One alternative to quirks, is to allow drivers to override the default
mmc host operations. This patch makes it easy to do that, and it is
needed for a subsequent bug fix, for which separate patches are
provided.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This used to return -EFAULT, but the function above returns -EINVAL on
the same condition so let's stick to that.
The removal of error return on this path was introduced with b093410c9a
('mmc: block: copy resp[] data on err for MMC_IOC_MULTI_CMD').
Fixes: b093410c9a ('mmc: block: copy resp[] data on err for MMC_IOC_MULTI_CMD').
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Grant Grundler <grundler@google.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the gpio driver is probed after the mmc one, the read/write gpio
and card detection one return -EPROBE_DEFER. Unfortunately, the memory
region remains requested, and upon the next probe, the probe will fail
anyway with -EBUSY.
Fix this by releasing the memory resource upon probe failure.
More broadly, this patch uses devm_*() primitives whenever possible in
the probe function.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no checks for dma mapping errors in mmc_spi.
Tha patch fixes that and by the way it adds dma_unmap_single(ones_dma)
that was left on a failure path mmc_spi_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The device power usage counter is increased by pm_runtime_get_noresume
but isn't decreased in err_add_host error path.
Fix this issue by calling pm_runtime_put_noidle() in the error path to
restore the device's power usage counter.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: f5f17813ae ("mmc: sdhci-of-at91: add PM support)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit fixing the conversion of pxamci to slot-gpio API fixed the
inverted the logic of the read-only gpio. Unfortunately, the commit was
tested on a non-inverted gpio, and not on the inverted one. And the fix
did work partially, by luck.
This is the remaining missing part of the fix, trivial but still necessary.
Fixes: Fixes: 26d49fe719 ("mmc: pxamci: fix read-only gpio detection polarity")
Reported-by: Andrea Adami <andrea.adami@gmail.com>
Tested-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Restore reset-gpios to be optional in pwrseq_simple
- Allow SDIO tuple for CISTPL_SDIO_STD
- Print correct voltage value in debugfs
- Enable tuning according to the actual timing
- Limit SD card power limit according to cards capabilities
MMC host:
- tmio_mmc_dma: don't print invalid DMA cookie
- mmci: Pick the correct variant and allow 8-bit mode for Nomadik
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dHj5
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.5-rc1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.5 rc1.
MMC core:
- Restore reset-gpios to be optional in pwrseq_simple
- Allow SDIO tuple for CISTPL_SDIO_STD
- Print correct voltage value in debugfs
- Enable tuning according to the actual timing
- Limit SD card power limit according to cards capabilities
MMC host:
- tmio_mmc_dma: don't print invalid DMA cookie
- mmci: Pick the correct variant and allow 8-bit mode for Nomadik"
* tag 'mmc-v4.5-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: pwrseq_simple: Make reset-gpios optional to match doc
mmc: sdio_cis: fix unknown tuple for CISTPL_SDIO_STD
mmc: debugfs: correct wrong voltage value
mmc: tmio_mmc_dma: don't print invalid DMA cookie
mmc: core: Enable tuning according to the actual timing
mmc: mmci: support 8bit mode on the Nomadik
mmc: mmci: fix an ages old detection error
mmc: sd: limit SD card power limit according to cards capabilities
The DT binding doc says reset-gpios is an optional property but the code
currently bails out if it is omitted.
This is a regression since it breaks previously working device trees.
Fix it by restoring the original documented behaviour.
Fixes: ce03727586 ("mmc: pwrseq_simple: use GPIO descriptors array API")
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CISTPL_SDIO_STD(0x91) is a known tuple, but sdio_cis don't define it, so
we get the warning below while probing several sdio wifi cards.
Refer to SDIO spec, it's not needed to parse the tuple, so this patch make
it a known one.
[ 4.098980] mmc2: queuing unknown CIS tuple 0x91 (3 bytes)
[ 4.099033] mmc2: new ultra high speed SDR104 SDIO card at address 0001
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull AVR32 updates from Hans-Christian Noren Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
mmc: atmel: get rid of struct mci_dma_data
mmc: atmel-mci: restore dma on AVR32
avr32: wire up missing syscalls
avr32: wire up accept4 syscall
As struct mci_dma_data is now only used by AVR32, it is nothing but
pointless indirection. Replace it with struct dw_dma_slave in the
AVR32 platform code and with a void pointer elsewhere.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit ecb89f2f5f ("mmc: atmel-mci: remove compat for non DT board
when requesting dma chan") broke dma on AVR32 and any other boards not
using DT. This restores a fallback mechanism for such cases.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
The tmio_mmc_start_dma_{rx,tx} function functions contain debug
code that prints the dma cookie among other things. However,
in case we fall back to PIO mode for some reason, the cookie
variable is never initialized, and gcc warns about this:
In file included from ../include/linux/printk.h:277:0,
from ../include/linux/kernel.h:13,
from ../include/linux/list.h:8,
from ../include/linux/kobject.h:20,
from ../include/linux/device.h:17,
from ../drivers/mmc/host/tmio_mmc_dma.c:13:
../drivers/mmc/host/tmio_mmc_dma.c: In function 'tmio_mmc_start_dma':
../include/linux/dynamic_debug.h:86:3: warning: 'cookie' may be used uninitialized in this function [-Wmaybe-uninitialized]
__dynamic_dev_dbg(&descriptor, dev, fmt, \
^
../drivers/mmc/host/tmio_mmc_dma.c:128:15: note: 'cookie' was declared here
dma_cookie_t cookie;
This modifies the dev_dbg() statements so we only print the cookie
when we are already in the DMA path.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While in sdhci_execute_tuning() the choice whether or not to enable the
tuning is done on the actual timing, in the mmc_sdio_init_uhs_card() the
check is done on the capability of the card.
This difference is causing some issues with some SDIO cards in DDR50
mode where the CDM19 is wrongly issued.
With this patch we modify the check in both
mmc_(sd|sdio)_init_uhs_card() functions to take the proper decision
only according to the actual timing specification.
Cc: stable@vger.kernel.org
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 4956e10903 ("ARM: 6244/1: mmci: add variant data and default
MCICLOCK support") added variant data for ARM, U300 and Ux500 variants.
The Nomadik NHK8815/8820 variant was erroneously labeled as a U300
variant, and when the proper Nomadik variant was later introduced in
commit 34fd421349 ("ARM: 7378/1: mmci: add support for the Nomadik MMCI
variant") this was not fixes. Let's say this fixes the latter commit as
there was no proper Nomadik support until then.
Cc: stable@vger.kernel.org
Fixes: 34fd421349 ("ARM: 7378/1: mmci: add support for the Nomadik...")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD card specification allows cards to error out a SWITCH command
where the requested function in a group is not supported. The spec
provides for a set of capabilities which indicate which functions are
supported.
In the case of the power limit, requesting an unsupported power level
via the SWITCH command fails, resulting in the power level remaining at
the power-on default of 0.72W, even though the host and card may support
higher powers levels.
This has been seen with SanDisk 8GB cards, which support the default
0.72W and 1.44W (200mA and 400mA) in combination with an iMX6 host,
supporting up to 2.88W (800mA). This currently causes us to try to set
a power limit function value of '3' (2.88W) which the card errors out
on, and thereby causes the power level to remain at 0.72W rather than
the desired 1.44W.
Arrange to limit the selected current limit by the capabilities reported
by the card to avoid the SWITCH command failing. Select the highest
current limit that the host and card combination support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes: a39ca6ae0a ("mmc: core: Simplify and fix for SD switch processing")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The misc control register is 32bit wide, the used readw/writew
accessors only mainipulate the low 16bit of this register. It
currently doesn't matter as all the bit changed are located in
the lower half, but together with the u32 variable used to hold
the contents of the register it is seriously confusing.
Switch to 32bit accessors to avoid any future breakage.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Keep the quirk bits, as Tegra30 and Tegra114 host have different levels
of support for UHS-I modes and so need different spare bits to be set,
but change the logic to be positive.
Tegra210 needs a different tuning sequence than Tegra30+. Disable
UHS modes until support for this is properly added.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This implements the UHS tuning sequence in a similar way to the one
contained in the TRM. It deviates in the way how to check if the tap
value is passing, by using the common Linux MMC function, which does
not only check for data CRC errors, but also if the received block
pattern is correct.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Tegra30 and up TRM states that this bit should always be
programmed to 0 by driver software.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow the the driver to change the clock supplied from the CAR directly,
minimizing the need to divide the clock inside the SDMMC module itself.
This allows for higher clock speeds than the default 48MHz supplied to
the module and is a prerequisite to support DDR signaling modes, where
the Tegra host needs to be run with a fixed internal divider of 2 for
data to be sampled correctly. (Tegra K1 TRM v03p chapter 29.7.1.1)
Also enable the broken preset value quirk as the preset values need to
be adapted to the changed clocking. While Tegra114+ allows this through
vendor registers, there is no such way for Tegra30. Takes the easy way
out and keep things consistent between the different SoC generations by
flagging the preset registers as unusable.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After commit 52221610dd ("mmc: sdhci: Improve external VDD regulator
support"), for the VDD is supplied via external regulators, we ignore
the code to convert a VDD voltage request into one of the standard
SDHCI voltage levels, then program it in the SDHCI_POWER_CONTROL. This
brings two issues:
1. SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON quirk isn't handled properly any
more.
2. What's more, once SDHCI_POWER_ON bit is set, some controllers such
as the sdhci-pxav3 used in marvell berlin SoCs require the voltage
levels programming in the SDHCI_POWER_CONTROL register, even the VDD
is supplied by external regulator. So the host in marvell berlin SoCs
still works fine after the commit. However, commit 3cbc6123a9 ("mmc:
sdhci: Set SDHCI_POWER_ON with external vmmc") sets the SDHCI_POWER_ON
bit, this would make the host in marvell berlin SoCs won't work any
more with external vmmc.
This patch restores the behavior when setting VDD through external
regulator by moving the call of mmc_regulator_set_ocr() to the end
of sdhci_set_power() function.
After this patch, the sdcard on Marvell Berlin SoC boards work again.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Fixes: 52221610dd ("mmc: sdhci: Improve external VDD ...")
Reviewed-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A card can be removed while it is runtime suspended.
Do not print an error message.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is quite common for Android devices to utilize more
then 8 partitions on internal eMMC storage.
The vanilla kernel can support this via
CONFIG_MMC_BLOCK_MINORS, however that solution caps the
system to 256 minors total, which limits the number of
mmc cards the system can support.
This patch, which has been carried for quite awhile in
the AOSP common tree, provides an alternative solution
that doesn't seem to limit the total card count. So I
wanted to submit it for consideration upstream.
This patch sets the GENHD_FL_EXT_DEVT flag, which will
allocate minor number in major 259 for partitions past
disk->minors.
It also removes the use of disk_devt to determine devidx
from md->disk. md->disk->first_minor is always initialized
from devidx and can always be used to recover it.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Austin S Hemmelgarn <ahferroin7@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Android Kernel Team <kernel-team@android.com>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Colin Cross <ccross@android.com>
[jstultz: Added context to commit message]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc workqueue is an ordered workqueue, allowing only one work to
execute per given time. As this workqueue is used for card detection, the
conseqeunce is that cards will be detected one by one waiting for each
other.
Moreover, most of the time spent during card initialization is waiting for
the card's internal firmware to be ready. From a CPU perspective this
typically means waiting for a completion variable to be kicked via an
IRQ-handler or waiting for a sleep timer to finish.
This behaviour of detecting/initializing cards is sub-optimal, especially
for SOCs having several controllers/cards.
Let's convert to use the system_freezable_wq for the mmc detect works.
This enables several works to be executed simultaneously and thus also
cards to be detected like so.
Tests on UX500, which holds two eMMC cards and an SD-card (actually also
an SDIO card, currently not detected), shows a significant improved
behaviour due to this change.
Before this change, both the eMMC cards waited for the SD card to be
initialized as its detect work entered the workqueue first. In some cases,
depending on the characteristic of the SD-card, they got delayed 1-1.5 s.
Additionally for the second eMMC, it needed to wait for the first eMMC to
be initialized which added another 120-190 ms.
Converting to the system_freezable_wq, removed these delays and made both
the eMMC cards available far earlier in the boot sequence.
Selecting the system_freezable_wq, in favour of for example the system_wq,
is because we need card detection mechanism to be disabled once userspace
are frozen during system PM. Currently the mmc core deal with this via PM
notifiers, but following patches may utilize the behaviour of the
system_freezable_wq, to simplify the use of the PM notifiers.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Alan Cooper <alcooperx@gmail.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
The dw_mmc driver stores the physical address of the MMIO registers
in a pointer, which requires the use of type casts, and is actually
broken if anyone ever has this device on a 32-bit SoC in registers
above 4GB. Gcc warns about this possibility when the driver is built
with ARM LPAE enabled:
mmc/host/dw_mmc.c: In function 'dw_mci_edmac_start_dma':
mmc/host/dw_mmc.c:702:17: warning: cast from pointer to integer of different size
cfg.dst_addr = (dma_addr_t)(host->phy_regs + fifo_offset);
^
mmc/host/dw_mmc-pltfm.c: In function 'dw_mci_pltfm_register':
mmc/host/dw_mmc-pltfm.c:63:19: warning: cast to pointer from integer of different size
host->phy_regs = (void *)(regs->start);
This changes the code to use resource_size_t, which gets rid of the
warning, the bug and the useless casts.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
there is a time window between __mmc_send_status() and time_afer(),
on some eMMC chip, the timeout_ms is only 10ms, if this thread was
scheduled out during this period, then, even card has already changes
to transfer state by the result of CMD13, this part of code also treat
it to timeout error.
So, need calculate timeout first, then call __mmc_send_status(), if
already timeout and card still in programing state, then treat it to
the real timeout error.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit bb08a7d489 ("mmc: usdhi6rol0: fix NULL pointer deref in debug
print") fixed one NULL pointer dereference but unfortunately introduced
another. "data" may be NULL if this is a command timeout for a command
without any data, so we should only use it if we're actually waiting for
data.
Fixes: bb08a7d489 ("mmc: usdhi6rol0: fix NULL pointer deref in debug print")
Cc: stable@vger.kernel.org # v4.3
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If no primary handler is specified for threaded_irq then a
default one is assigned which always returns IRQ_WAKE_THREAD.
This handler requires the IRQF_ONESHOT, because the source of
interrupt is not disabled
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
there are too many error logs shown when use CMD21/CMD19 to do tune,
and it will appear at each resume time, print out so many logs to the
uart console cost too mush time. so change it to dev_dbg.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, PM core supports asynchronous suspend/resume mode for devices
during system suspend/resume, and the power state transition of one
device may be completed in separate kernel thread. PM core ensures
all power state transition dependency between devices. This patch
enables MMC/SD/SDIO card and SDIO function devices to suspend/resume
asynchronously. This will take advantage of multicore and improve
system suspend/resume speed. After applying this patch and enabling
all SDIO function's child devices to suspend/resume asynchronously
on ASUS T100TA, the system suspend-to-idle time is reduced from
1645ms to 1108ms, and the system resume time is reduced from 940ms
to 918ms.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
