The TC3589x driver is now a device tree-only driver, so we want
only dynamic IRQs and GPIO numbers from the tc3589x, no static
assignments.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These registers are documented in the datasheet and used as part of the
extcon driver. Expose them properly through regmap as the datasheet
notes they should be treated as volatile do so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Technically this register is not used on wm8997 however the regmap core
requires a continuous block of IRQs. The simplest solution is just to
add the register.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Change clk_enable/disable() calls to clk_prepare_enable() and
clk_disable_unrepapre().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
First spotted pointless (incorrect) indent of 'if (ret)', then double
indentations of a struct attribute 'mask'. Decided to go through the
whole file and make amendments instead and this is the result.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some boards with TC6393XB chip require full state restore during system
resume thanks to chip's VCC being cut off during suspend (Sharp SL-6000
tosa is one of them). Failing to do so would result in ohci Oops on
resume due to internal memory contentes being changed. Fail ohci suspend
on tc6393xb is full state restore is required.
Recommended workaround is to unbind tmio-ohci driver before suspend and
rebind it after resume.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MFD core already cares about failing registration. It will remove successfully
registered devices in case of error. Thus, no need to repeatedly call
mfd_remove_devices().
Fixes: 5829e9b64e (mfd: lpc_sch: Accomodate partial population of the MFD devices)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Precedence of & and >> is not the same and is not left to right.
shift has higher precedence and should be done after the mask.
Add parentheses around the mask.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
ab8500_restart is not called from anywhere in the kernel, so drop it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Error check around return value of devm_ioremap is missing. Add the same
to avoid NULL pointer dereference.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit e7cd1d1eb1 ("mfd: twl4030-power: Add generic reset
configuration") accidentally removed the compatible flag for
"ti,twl4030-power" that should be there as documented in the
binding.
If "ti,twl4030-power" only the poweroff configuration is done
by the driver.
Fixes: e7cd1d1eb1 ("mfd: twl4030-power: Add generic reset configuration")
Cc: stable@vger.kernel.org # v3.16+
Reported-by: "Dr. H. Nikolaus Schaller" <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix rts5227&5249 failed send buffer cmd after suspend,
PM_CTRL3 should reset before send any buffer cmd after suspend.
Otherwise, buffer cmd will failed, this will lead resume fail.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This reverts commit b7cde7078d
("mfd: sec-core: Prepare regulators for suspend state to reduce power-consumption")
Commit b7cde7078d called regulator_suspend_prepare() to prepare the
regulators for a suspend state. But it did from the device pm suspend
handler while the regulator suspend prepare function iterates over all
regulators and not only the one managed by this device so it doesn't
seems to be correct to call it from within a device driver.
It is better to call the regulator suspend prepare/finish functions
from platform code instead so this patch reverts the mentioned commit.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a "maxim,max77693-charger" of_compatible to the mfd_cell so the MFD
child device (the charger) will have its own of_node set. This will be
used by the max77693 charger driver in next patches to obtain battery
configuration from DTS.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This was found whilst running checkpatch.pl on arizona-spi.
WARNING: Missing a blank line after declarations
+ struct arizona *arizona = spi_get_drvdata(spi);
+ arizona_dev_exit(arizona);
Signed-off-by: Will Sheppard <wsheppard@embedded-bits.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The HLCDC IP available on some Atmel SoCs (i.e. at91sam9n12, at91sam9x5
family or sama5d3 family) exposes 2 subdevices:
- a display controller (controlled by a DRM driver)
- a PWM chip
The MFD device provides a regmap and several clocks (those connected
to this hardware block) to its subdevices.
This way concurrent accesses to the iomem range are handled by the regmap
framework, and each subdevice can safely access HLCDC registers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Anthony Harivel <anthony.harivel@emtrion.de>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Make sure to always honour multi-function devices registered with
PLATFORM_DEVID_NONE (-1) or PLATFORM_DEVID_AUTO (-2) as id base. In this
case it does not make sense to append the cell id to the mfd-id base and
potentially change the requested behaviour.
Specifically this will allow multi-function devices to be registered
with PLATFORM_DEVID_AUTO while still having non-zero cell ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use mfd_add_hotplug_devices helper to register the subdevices.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently a syscon entity can be only registered directly through a
platform device that binds to a dedicated syscon driver. However in
certain use cases it is desirable to make a device used with another
driver a syscon interface provider.
For example, certain SoCs (e.g. Exynos) contain system controller
blocks which perform various functions such as power domain control,
CPU power management, low power mode control, but in addition contain
certain IP integration glue, such as various signal masks,
coprocessor power control, etc. In such case, there is a need to have
a dedicated driver for such system controller but also share registers
with other drivers. The latter is where the syscon interface is helpful.
In case of DT based platforms, this patch decouples syscon object from
syscon platform driver, and allows to create syscon objects first time
when it is required by calling of syscon_regmap_lookup_by APIs and keep
a list of such syscon objects along with syscon provider device_nodes
and regmap handles.
For non-DT based platforms, this patch keeps syscon platform driver
structure so that syscon can be probed and such non-DT based drivers
can use syscon_regmap_lookup_by_pdev API and access regmap handles.
Once all users of "syscon_regmap_lookup_by_pdev" migrated to DT based,
we can completely remove platform driver of syscon, and keep only helper
functions to get regmap handles.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch add haptic of_compatible in order to use the haptic
device driver using Devicetree.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch add regmap_haptic initialization to use haptic register map
in haptic device driver.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Adds of_compatible strings to mfd_cells for sub devices of the tps65217.
Signed-off-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds S2MPS13 regulator device to existing S2MPS11 device driver.
The S2MPS13 has just different number of regulators from S2MPS14.
The S2MPS13 regulator device includes LDO[1-40] and BUCK[1-10].
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds the support for Samsung S2MPS13 PMIC device to the sec-core MFD
driver. The S2MPS13 is very similar with existing S2MPS14 and includes PMIC/
RTC/CLOCK devices.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Sparse catches a couple endian bugs.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The echo field in dln2_transfer_complete comes directly from an USB
transfer and we should not trust it is valid.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If wait_for_completion_interruptible_timeout returns a positive value
it may be propagated as the return value of _dln2_transfer. This
contradicts the documentation of the function and exposes unnecessary
internals to the callers.
This patch makes sure to set the return value to 0 in that case.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
IRQ numbers in axp20x devices are defined with high-order bit first
in each IRQ enable/status registers. On Intel platforms it is more
common to number IRQs with least significant bit first. Therefore,
sharing IRQ# between the two is very difficult. Since AXP288 is a
customized PMIC for Intel platform and the amount of shared IRQs are
very small, we use separate IRQ numbering. This also fixes collision
and a duplicate in WBTO interrupt.
e.g. For the 16 interrupts controlled in IRQ enabled registers 1 & 2,
on axp20x for ARM, the PMIC local IRQ numbers and register bits are
mapped as:
IRQ#: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
---------------------------------------------------------
ARM: 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
Intel: 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch implements the USB part of the Diolan USB-I2C/SPI/GPIO
Master Adapter DLN-2. Details about the device can be found here:
https://www.diolan.com/i2c/i2c_interface.html.
Information about the USB protocol can be found in the Programmer's
Reference Manual [1], see section 1.7.
Because the hardware has a single transmit endpoint and a single
receive endpoint the communication between the various DLN2 drivers
and the hardware will be muxed/demuxed by this driver.
Each DLN2 module will be identified by the handle field within the DLN2
message header. If a DLN2 module issues multiple commands in parallel
they will be identified by the echo counter field in the message header.
The DLN2 modules can use the dln2_transfer() function to issue a
command and wait for its response. They can also register a callback
that is going to be called when a specific event id is generated by
the device (e.g. GPIO interrupts). The device uses handle 0 for
sending events.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- DT clean-ups in da9055-core, max14577, rn5t618, arizona, hi6421, stmpe, twl4030
- Export symbols for use in modules in max14577
- Plenty of static code analysis/Coccinelle fixes throughout the SS
- Regmap clean-ups in arizona, wm5102, wm5110, da9052, tps65217, rk808
- Remove unused/duplicate code in da9052, 88pm860x, ti_ssp, lpc_sch, arizona
- Bug fixes in ti_am335x_tscadc, da9052, ti_am335x_tscadc, rtsx_pcr
- IRQ fixups in arizona, stmpe, max14577
- Regulator related changes in axp20x
- Pass DMA coherency information from parent => child in MFD core
- Rename DT document files for consistency
- Add ACPI support to the MFD core
- Add Andreas Werner to MAINTAINERS for MEN F21BMC
New drivers/supported devices:
- New driver for MEN 14F021P00 Board Management Controller
- New driver for Ricoh RN5T618 PMIC
- New driver for Rockchip RK808
- New driver for HiSilicon Hi6421 PMIC
- New driver for Qualcomm SPMI PMICs
- Add support for Intel Braswell in lpc_ich
- Add support for Intel 9 Series PCH in lpc_ich
- Add support for Intel Quark ILB in lpc_sch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xxsZ
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Changes to existing drivers:
- DT clean-ups in da9055-core, max14577, rn5t618, arizona, hi6421, stmpe, twl4030
- Export symbols for use in modules in max14577
- Plenty of static code analysis/Coccinelle fixes throughout the SS
- Regmap clean-ups in arizona, wm5102, wm5110, da9052, tps65217, rk808
- Remove unused/duplicate code in da9052, 88pm860x, ti_ssp, lpc_sch, arizona
- Bug fixes in ti_am335x_tscadc, da9052, ti_am335x_tscadc, rtsx_pcr
- IRQ fixups in arizona, stmpe, max14577
- Regulator related changes in axp20x
- Pass DMA coherency information from parent => child in MFD core
- Rename DT document files for consistency
- Add ACPI support to the MFD core
- Add Andreas Werner to MAINTAINERS for MEN F21BMC
New drivers/supported devices:
- New driver for MEN 14F021P00 Board Management Controller
- New driver for Ricoh RN5T618 PMIC
- New driver for Rockchip RK808
- New driver for HiSilicon Hi6421 PMIC
- New driver for Qualcomm SPMI PMICs
- Add support for Intel Braswell in lpc_ich
- Add support for Intel 9 Series PCH in lpc_ich
- Add support for Intel Quark ILB in lpc_sch"
[ Delayed to after the poweer/reset pull due to Kconfig problems with
recursive Kconfig select/depends-on chains. - Linus ]
* tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (79 commits)
mfd: cros_ec: wait for completion of commands that return IN_PROGRESS
i2c: i2c-cros-ec-tunnel: Set retries to 3
mfd: cros_ec: move locking into cros_ec_cmd_xfer
mfd: cros_ec: stop calling ->cmd_xfer() directly
mfd: cros_ec: Delay for 50ms when we see EC_CMD_REBOOT_EC
MAINTAINERS: Adds Andreas Werner to maintainers list for MEN F21BMC
mfd: arizona: Correct mask to allow setting micbias external cap
mfd: Add ACPI support
Revert "mfd: wm5102: Manually apply register patch"
mfd: ti_am335x_tscadc: Update logic in CTRL register for 5-wire TS
mfd: dt-bindings: atmel-gpbr: Rename doc file to conform to naming convention
mfd: dt-bindings: qcom-pm8xxx: Rename doc file to conform to naming convention
mfd: Inherit coherent_dma_mask from parent device
mfd: Document DT bindings for Qualcomm SPMI PMICs
mfd: Add support for Qualcomm SPMI PMICs
mfd: dt-bindings: pm8xxx: Add new compatible string
mfd: axp209x: Drop the parent supplies field
mfd: twl4030-power: Use 'ti,system-power-controller' as alternative way to support system power off
mfd: dt-bindings: twl4030-power: Use the standard property to mark power control
mfd: syscon: Add Atmel GPBR DT bindings documention
...
Convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
Register ntc_thermistor driver with thermal subsystem.
Add support for F15h M60h to k10temp driver.
Add driver for MEN14F021P00 BMC HWMON driver; this required a merge
with tag mfd-hwmon-leds-watchdog-v3.18.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vI5p
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for menf21bmc.
- convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
- register ntc_thermistor driver with thermal subsystem.
- add support for F15h M60h to k10temp driver.
- add driver for MEN14F021P00 BMC HWMON driver; this required a merge
with tag mfd-hwmon-leds-watchdog-v3.18
* tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ab8500) Call kernel_power_off instead of pm_power_off
hwmon: (menf21bmc) Introduce MEN14F021P00 BMC HWMON driver
leds: leds-menf21bmc: Introduce MEN 14F021P00 BMC LED driver
watchdog: menf21bmc_wdt: Introduce MEN 14F021P00 BMC Watchdog driver
mfd: menf21bmc: Introduce MEN 14F021P00 BMC MFD Core driver
hwmon: (ntc_thermistor) Add ntc thermistor to thermal subsystem as a sensor.
hwmon: (smsc47b397) Convert to devm_hwmon_device_register_with_groups
MAINTAINERS: add entry for the PWM fan driver
hwmon: (k10temp) Convert to devm_hwmon_device_register_with_groups
hwmon: (k10temp) Add support for F15h M60h
hwmon: (da9052) Convert to devm_hwmon_device_register_with_groups
hwmon: (da9055) Convert to devm_hwmon_device_register_with_groups
hwmon: (ads1015) Use of_property_read_u32 at appropriate places
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
X-Powers AXP288 is a customized PMIC for Intel Baytrail-CR platforms. Similar
to AXP202/209, AXP288 comes with USB charger, more LDO and BUCK channels, and
AD converters. It also provides extended status and interrupt reporting
capabilities than the devices currently supported in axp20x.c.
In addition to feature extension, this patch also adds ACPI binding for
enumeration.
This consolidated driver should support more X-Powers' PMICs in both device
tree and ACPI enumerated platforms.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When an EC command returns EC_RES_IN_PROGRESS, we need to query
the state of the EC until it indicates that it is no longer busy.
Do this in cros_ec_cmd_xfer() under the EC's mutex so that other
commands (e.g. keyboard, I2C passtru) aren't issued to the EC while
it is working on the in-progress command.
The 10 milliseconds delay and the number of retries are the values
that were used by the flashrom tool when retrying commands.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now that there's a central cros_ec_cmd_xfer(), move the locking
out of the SPI driver.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead of having users of the ChromeOS EC call the interface-specific
cmd_xfer() callback directly, introduce a central cros_ec_cmd_xfer()
to use instead. This will allow us to put all the locking and retry
logic in one place instead of duplicating it across the different
drivers.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If someone sends a EC_CMD_REBOOT_EC to the EC, the EC will likely be
unresponsive for quite a while. Add a delay to the end of the command
to prevent random failures of future commands.
NOTES:
* This could be optimized a bit by simply delaying the next command
sent, but EC_CMD_REBOOT_EC is such a rare command that the extra
complexity doesn't seem worth it.
* This is a bit of an "ugly hack" since the SPI driver is effectively
snooping on the communication and making a lot of assumptions. It
would be nice to architect in some better solution long term.
* This same logic probably needs to be applied to the i2c driver.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently the mask for the external capacitor bit is missing when
writing the MICBIAS config meaning it will never be set this patch fixes
this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If an MFD device is backed by ACPI namespace, we should allow subdevice
drivers to access their corresponding ACPI companion devices through normal
means (e.g using ACPI_COMPANION()).
This patch adds such support to the MFD core. If the MFD parent device
does not specify any ACPI _HID/_CID for the child device, the child
device will share the parent ACPI companion device. Otherwise the child
device will be assigned with the corresponding ACPI companion, if found
in the namespace below the parent.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This reverts commit d9d03496f6.
It seems this commit was applied twice, once through ASoC and once
through MFD:
commit 4c9bb8bc35
mfd: wm5102: Manually apply register patch
commit d9d03496f6
mfd: wm5102: Manually apply register patch
This has lead to a small piece of duplicate code. It is harmless hence
how it has gone unoticed for so long. This patch reverts one of the two
commits removing the unneeded code.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The logic in AFE_Pen_Ctrl bitmask in the CTRL register is different for five
wire versus four or eight wire touschscreens. This patch should fix this for
five-wire touch screens. There should be no change needed here for four and
eight wire tousch screens.
Signed-off-by: Jeff Lance <j-lance1@ti.com>
[bigeasy: keep the change mfd only]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
dma_mask and dma_parms are already inherited from the parent device but
dma_coherent_mask was left uninitialized (set to zero thanks to kzalloc).
Set sub-device coherent_dma_mask to its parent value to simplify
sub-drivers making use of dma coherent helper functions (those drivers
currently have to explicitly set the dma coherent mask using
dma_set_coherent_mask function).
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Qualcomm SPMI PMIC chips are components used with the
Snapdragon 800 series SoC family. This driver exists
largely as a glue mfd component, it exists to be an owner
of an SPMI regmap for children devices described in
device tree.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now that the regulator code get its parent supplies purely from the DT, we can
drop the parent supplies resources in the MFD driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
ti,system-power-controller is more or less the standard way of
indicating that the PMIC is the system wide power controller and hence
may be used to switch off the system. Almost ALL TI PMIC drivers and
many Maxim PMIC drivers follow the same style.
So support 'ti,system-power-controller' in addition to the usual
'ti,use_poweroff' to indicate that the PMIC instance has control for
switching off the system.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Let's define the voltatile registers (those that can't be cached) and
enable caching. The rk808 is accessed almost constantly with cpufreq
so this is really nice.
As measured by ftrace:
before this change: cpu0_set_target() => ~2200us
after this change: cpu0_set_target() => ~500us
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We use a dummy IRQ chip to dispatch interrupts to the two seperate IRQ
domains on the Arizona devices. This is just a simple software IRQ chip
and thus the current handle_edge_irq is unnecessary for its needs.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
