We should close link and all NIC operations during shutdown.
On some systems graceful reboot never closes NIC interface on its own,
but only indicates pci device shutdown. Without explicit handler, NIC
rx rings continued to transfer DMA data into prepared buffers while CPU
rebooted already. That caused memory corruptions on soft reboot.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing prevents us from changing MAC on the running interface.
Allow this with ndev priv flag.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should report to napi full budget only when we have more job to do.
Before this fix, on any tx queue cleanup we forced napi to do poll again.
Thats a waste of cpu resources and caused storming with napi polls when
there was at least one tx on each interrupt.
With this fix we report full budget only when there is more job on TX
to do. Or, as before, when rx budget was fully consumed.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
B1 hardware changes behavior of mailbox interface, it has busy bit
always raised. Data ready condition should be detected by increment
of address register.
Old code has empty `for` loop, and that caused cpu overloads on B1
hardware. aq_nic_service_timer_cb consumed ~100ms because of that.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW 1.5.58 and below needs a fixed delay even after 0x18 register
is filled. Otherwise, setting MPI_INIT state too fast causes
traffic hang.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under some circumstances (notably using thunderbolt interface) SPI
on chip reset may be in active transaction.
Here we forcibly cleanup SPI to prevent possible hangups.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: fixes 2018-03-20
Please apply one final set of qeth patches for 4.16.
All of these fix long-standing bugs, so please queue them up for -stable
as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the IRQ handler determines that one of the cmd IO channels has
failed and schedules recovery, block any further cmd requests from
being submitted. The request would inevitably stall, and prevent the
recovery from making progress until the request times out.
This sort of error was observed after Live Guest Relocation, where
the pending IO on the READ channel intentionally gets terminated to
kick-start recovery. Simultaneously the guest executed SIOCETHTOOL,
triggering qeth to issue a QUERY CARD INFO command. The command
then stalled in the inoperabel WRITE channel.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For calling ccw_device_start(), issue_next_read() needs to hold the
device's ccwlock.
This is satisfied for the IRQ handler path (where qeth_irq() gets called
under the ccwlock), but we need explicit locking for the initial call by
the MPC initialization.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_wait_for_threads() is potentially called by multiple users, make
sure to notify all of them after qeth_clear_thread_running_bit()
adjusted the thread_running_mask. With no timeout, callers would
otherwise stall.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On removal, a qeth card's netdevice is currently not properly freed
because the call chain looks as follows:
qeth_core_remove_device(card)
lx_remove_device(card)
unregister_netdev(card->dev)
card->dev = NULL !!!
qeth_core_free_card(card)
if (card->dev) !!!
free_netdev(card->dev)
Fix it by free'ing the netdev straight after unregistering. This also
fixes the sysfs-driven layer switch case (qeth_dev_layer2_store()),
where the need to free the current netdevice was not considered at all.
Note that free_netdev() takes care of the netif_napi_del() for us too.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Hao says:
====================
net: phy: Add general dummy stubs for MMD register access
v2:
As suggested by Andrew:
- Add general dummy stubs
- Also use that for the micrel phy
This patch series fix the Ethernet broken on the mpc8315erdb board introduced
by commit b6b5e8a691 ("gianfar: Disable EEE autoneg by default").
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The new general dummy stubs for MMD register access were introduced.
Use that for the codes reuse.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet on mpc8315erdb is broken since commit b6b5e8a691
("gianfar: Disable EEE autoneg by default"). The reason is that
even though the rtl8211b doesn't support the MMD extended registers
access, it does return some random values if we trying to access
the MMD register via indirect method. This makes it seem that the
EEE is supported by this phy device. And the subsequent writing to
the MMD registers does cause the phy malfunction. So use the dummy
stubs for the MMD register access to fix this issue.
Fixes: b6b5e8a691 ("gianfar: Disable EEE autoneg by default")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some phy devices, even though they don't support the MMD extended
register access, it does have some side effect if we are trying to
read/write the MMD registers via indirect method. So introduce general
dummy stubs for MMD register access which these devices can use to avoid
such side effect.
Fixes: b6b5e8a691 ("gianfar: Disable EEE autoneg by default")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix possible IPv6 packet loss when multicast extension is used, by Linus Luessing
- fix SKB handling issues for TTVN and DAT, by Matthias Schiffer (two patches)
- fix include for eventpoll, by Sven Eckelmann
- fix skb checksum for ttvn reroutes, by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=hsM8
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20180319' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- fix possible IPv6 packet loss when multicast extension is used, by Linus Luessing
- fix SKB handling issues for TTVN and DAT, by Matthias Schiffer (two patches)
- fix include for eventpoll, by Sven Eckelmann
- fix skb checksum for ttvn reroutes, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti says:
====================
fix idr leak in actions
This series fixes situations where a temporary failure to install a TC
action results in the permanent impossibility to reuse the configured
value of 'index'.
Thanks to Cong Wang for the initial review.
v2: fix build error in act_ipt.c, reported by kbuild test robot
====================
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcf_skbmod_init() can fail after the idr has been successfully reserved.
When this happens, every subsequent attempt to configure skbmod rules
using the same idr value will systematically fail with -ENOSPC, unless
the first attempt was done using the 'replace' keyword:
# tc action add action skbmod swap mac index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action add action skbmod swap mac index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
# tc action add action skbmod swap mac index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
...
Fix this in tcf_skbmod_init(), ensuring that tcf_idr_release() is called
on the error path when the idr has been reserved, but not yet inserted.
Also, don't test 'ovr' in the error path, to avoid a 'replace' failure
implicitly become a 'delete' that leaks refcount in act_skbmod module:
# rmmod act_skbmod; modprobe act_skbmod
# tc action add action skbmod swap mac index 100
# tc action add action skbmod swap mac continue index 100
RTNETLINK answers: File exists
We have an error talking to the kernel
# tc action replace action skbmod swap mac continue index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action list action skbmod
#
# rmmod act_skbmod
rmmod: ERROR: Module act_skbmod is in use
Fixes: 65a206c01e ("net/sched: Change act_api and act_xxx modules to use IDR")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcf_vlan_init() can fail after the idr has been successfully reserved.
When this happens, every subsequent attempt to configure vlan rules using
the same idr value will systematically fail with -ENOSPC, unless the first
attempt was done using the 'replace' keyword.
# tc action add action vlan pop index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action add action vlan pop index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
# tc action add action vlan pop index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
...
Fix this in tcf_vlan_init(), ensuring that tcf_idr_release() is called on
the error path when the idr has been reserved, but not yet inserted. Also,
don't test 'ovr' in the error path, to avoid a 'replace' failure implicitly
become a 'delete' that leaks refcount in act_vlan module:
# rmmod act_vlan; modprobe act_vlan
# tc action add action vlan push id 5 index 100
# tc action replace action vlan push id 7 index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action list action vlan
#
# rmmod act_vlan
rmmod: ERROR: Module act_vlan is in use
Fixes: 4c5b9d9642 ("act_vlan: VLAN action rewrite to use RCU lock/unlock and update")
Fixes: 65a206c01e ("net/sched: Change act_api and act_xxx modules to use IDR")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__tcf_ipt_init() can fail after the idr has been successfully reserved.
When this happens, subsequent attempts to configure xt/ipt rules using
the same idr value systematically fail with -ENOSPC:
# tc action add action xt -j LOG --log-prefix test1 index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "test1" index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
Command "(null)" is unknown, try "tc actions help".
# tc action add action xt -j LOG --log-prefix test1 index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "test1" index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
Command "(null)" is unknown, try "tc actions help".
# tc action add action xt -j LOG --log-prefix test1 index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "test1" index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
...
Fix this in the error path of __tcf_ipt_init(), calling tcf_idr_release()
in place of tcf_idr_cleanup(). Since tcf_ipt_release() can now be called
when tcfi_t is NULL, we also need to protect calls to ipt_destroy_target()
to avoid NULL pointer dereference.
Fixes: 65a206c01e ("net/sched: Change act_api and act_xxx modules to use IDR")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcf_pedit_init() can fail to allocate 'keys' after the idr has been
successfully reserved. When this happens, subsequent attempts to configure
a pedit rule using the same idr value systematically fail with -ENOSPC:
# tc action add action pedit munge ip ttl set 63 index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action add action pedit munge ip ttl set 63 index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
# tc action add action pedit munge ip ttl set 63 index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
...
Fix this in the error path of tcf_act_pedit_init(), calling
tcf_idr_release() in place of tcf_idr_cleanup().
Fixes: 65a206c01e ("net/sched: Change act_api and act_xxx modules to use IDR")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcf_act_police_init() can fail after the idr has been successfully
reserved (e.g., qdisc_get_rtab() may return NULL). When this happens,
subsequent attempts to configure a police rule using the same idr value
systematiclly fail with -ENOSPC:
# tc action add action police rate 1000 burst 1000 drop index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action add action police rate 1000 burst 1000 drop index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
# tc action add action police rate 1000 burst 1000 drop index 100
RTNETLINK answers: No space left on device
...
Fix this in the error path of tcf_act_police_init(), calling
tcf_idr_release() in place of tcf_idr_cleanup().
Fixes: 65a206c01e ("net/sched: Change act_api and act_xxx modules to use IDR")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if the kernel fails to duplicate 'sdata', creation of a new action fails
with -ENOMEM. However, subsequent attempts to install the same action
using the same value of 'index' systematically fail with -ENOSPC, and
that value of 'index' will no more be usable by act_simple, until rmmod /
insmod of act_simple.ko is done:
# tc actions add action simple sdata hello index 100
# tc actions list action simple
action order 0: Simple <hello>
index 100 ref 1 bind 0
# tc actions flush action simple
# tc actions add action simple sdata hello index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc actions flush action simple
# tc actions add action simple sdata hello index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
# tc actions add action simple sdata hello index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
...
Fix this in the error path of tcf_simp_init(), calling tcf_idr_release()
in place of tcf_idr_cleanup().
Fixes: 65a206c01e ("net/sched: Change act_api and act_xxx modules to use IDR")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when the following command sequence is entered
# tc action add action bpf bytecode '4,40 0 0 12,31 0 1 2048,6 0 0 262144,6 0 0 0' index 100
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
# tc action add action bpf bytecode '4,40 0 0 12,21 0 1 2048,6 0 0 262144,6 0 0 0' index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
act_bpf correctly refuses to install the first TC rule, because 31 is not
a valid instruction. However, it refuses to install the second TC rule,
even if the BPF code is correct. Furthermore, it's no more possible to
install any other rule having the same value of 'index' until act_bpf
module is unloaded/inserted again. After the idr has been reserved, call
tcf_idr_release() instead of tcf_idr_cleanup(), to fix this issue.
Fixes: 65a206c01e ("net/sched: Change act_api and act_xxx modules to use IDR")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistakes in DP_ERR error message text and
comments
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in BNX2X_ERR error message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-03-21
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Follow-up fix to the fault injection framework to prevent jump
optimization on the kprobe by installing a dummy post-handler,
from Masami.
2) Drop bpf_perf_prog_read_value helper from tracepoint type programs
which was mistakenly added there and would otherwise crash due to
wrong input context, from Yonghong.
3) Fix a crash in BPF fs when compiled with clang. Code appears to
be fine just that clang tries to overly aggressive optimize in
non C conform ways, therefore fix the kernel's Makefile to
generally prevent such issues, from Daniel.
4) Skip unnecessary capability checks in bpf syscall, which is otherwise
triggering unnecessary security hooks on capability checking and
causing false alarms on unprivileged processes trying to access
CAP_SYS_ADMIN restricted infra, from Chenbo.
5) Fix the test_bpf.ko module when CONFIG_BPF_JIT_ALWAYS_ON is set
with regards to a test case that is really just supposed to fail
on x8_64 JIT but not others, from Thadeu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Prasad reported that he has seen crashes in BPF subsystem with netd
on Android with arm64 in the form of (note, the taint is unrelated):
[ 4134.721483] Unable to handle kernel paging request at virtual address 800000001
[ 4134.820925] Mem abort info:
[ 4134.901283] Exception class = DABT (current EL), IL = 32 bits
[ 4135.016736] SET = 0, FnV = 0
[ 4135.119820] EA = 0, S1PTW = 0
[ 4135.201431] Data abort info:
[ 4135.301388] ISV = 0, ISS = 0x00000021
[ 4135.359599] CM = 0, WnR = 0
[ 4135.470873] user pgtable: 4k pages, 39-bit VAs, pgd = ffffffe39b946000
[ 4135.499757] [0000000800000001] *pgd=0000000000000000, *pud=0000000000000000
[ 4135.660725] Internal error: Oops: 96000021 [#1] PREEMPT SMP
[ 4135.674610] Modules linked in:
[ 4135.682883] CPU: 5 PID: 1260 Comm: netd Tainted: G S W 4.14.19+ #1
[ 4135.716188] task: ffffffe39f4aa380 task.stack: ffffff801d4e0000
[ 4135.731599] PC is at bpf_prog_add+0x20/0x68
[ 4135.741746] LR is at bpf_prog_inc+0x20/0x2c
[ 4135.751788] pc : [<ffffff94ab7ad584>] lr : [<ffffff94ab7ad638>] pstate: 60400145
[ 4135.769062] sp : ffffff801d4e3ce0
[...]
[ 4136.258315] Process netd (pid: 1260, stack limit = 0xffffff801d4e0000)
[ 4136.273746] Call trace:
[...]
[ 4136.442494] 3ca0: ffffff94ab7ad584 0000000060400145 ffffffe3a01bf8f8 0000000000000006
[ 4136.460936] 3cc0: 0000008000000000 ffffff94ab844204 ffffff801d4e3cf0 ffffff94ab7ad584
[ 4136.479241] [<ffffff94ab7ad584>] bpf_prog_add+0x20/0x68
[ 4136.491767] [<ffffff94ab7ad638>] bpf_prog_inc+0x20/0x2c
[ 4136.504536] [<ffffff94ab7b5d08>] bpf_obj_get_user+0x204/0x22c
[ 4136.518746] [<ffffff94ab7ade68>] SyS_bpf+0x5a8/0x1a88
Android's netd was basically pinning the uid cookie BPF map in BPF
fs (/sys/fs/bpf/traffic_cookie_uid_map) and later on retrieving it
again resulting in above panic. Issue is that the map was wrongly
identified as a prog! Above kernel was compiled with clang 4.0,
and it turns out that clang decided to merge the bpf_prog_iops and
bpf_map_iops into a single memory location, such that the two i_ops
could then not be distinguished anymore.
Reason for this miscompilation is that clang has the more aggressive
-fmerge-all-constants enabled by default. In fact, clang source code
has a comment about it in lib/AST/ExprConstant.cpp on why it is okay
to do so:
Pointers with different bases cannot represent the same object.
(Note that clang defaults to -fmerge-all-constants, which can
lead to inconsistent results for comparisons involving the address
of a constant; this generally doesn't matter in practice.)
The issue never appeared with gcc however, since gcc does not enable
-fmerge-all-constants by default and even *explicitly* states in
it's option description that using this flag results in non-conforming
behavior, quote from man gcc:
Languages like C or C++ require each variable, including multiple
instances of the same variable in recursive calls, to have distinct
locations, so using this option results in non-conforming behavior.
There are also various clang bug reports open on that matter [1],
where clang developers acknowledge the non-conforming behavior,
and refer to disabling it with -fno-merge-all-constants. But even
if this gets fixed in clang today, there are already users out there
that triggered this. Thus, fix this issue by explicitly adding
-fno-merge-all-constants to the kernel's Makefile to generically
disable this optimization, since potentially other places in the
kernel could subtly break as well.
Note, there is also a flag called -fmerge-constants (not supported
by clang), which is more conservative and only applies to strings
and it's enabled in gcc's -O/-O2/-O3/-Os optimization levels. In
gcc's code, the two flags -fmerge-{all-,}constants share the same
variable internally, so when disabling it via -fno-merge-all-constants,
then we really don't merge any const data (e.g. strings), and text
size increases with gcc (14,927,214 -> 14,942,646 for vmlinux.o).
$ gcc -fverbose-asm -O2 foo.c -S -o foo.S
-> foo.S lists -fmerge-constants under options enabled
$ gcc -fverbose-asm -O2 -fno-merge-all-constants foo.c -S -o foo.S
-> foo.S doesn't list -fmerge-constants under options enabled
$ gcc -fverbose-asm -O2 -fno-merge-all-constants -fmerge-constants foo.c -S -o foo.S
-> foo.S lists -fmerge-constants under options enabled
Thus, as a workaround we need to set both -fno-merge-all-constants
*and* -fmerge-constants in the Makefile in order for text size to
stay as is.
[1] https://bugs.llvm.org/show_bug.cgi?id=18538
Reported-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Chenbo Feng <fengc@google.com>
Cc: Richard Smith <richard-llvm@metafoo.co.uk>
Cc: Chandler Carruth <chandlerc@gmail.com>
Cc: linux-kernel@vger.kernel.org
Tested-by: Prasad Sodagudi <psodagud@codeaurora.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The current check statement in BPF syscall will do a capability check
for CAP_SYS_ADMIN before checking sysctl_unprivileged_bpf_disabled. This
code path will trigger unnecessary security hooks on capability checking
and cause false alarms on unprivileged process trying to get CAP_SYS_ADMIN
access. This can be resolved by simply switch the order of the statement
and CAP_SYS_ADMIN is not required anyway if unprivileged bpf syscall is
allowed.
Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Commit 4bebdc7a85 ("bpf: add helper bpf_perf_prog_read_value")
added helper bpf_perf_prog_read_value so that perf_event type program
can read event counter and enabled/running time.
This commit, however, introduced a bug which allows this helper
for tracepoint type programs. This is incorrect as bpf_perf_prog_read_value
needs to access perf_event through its bpf_perf_event_data_kern type context,
which is not available for tracepoint type program.
This patch fixed the issue by separating bpf_func_proto between tracepoint
and perf_event type programs and removed bpf_perf_prog_read_value
from tracepoint func prototype.
Fixes: 4bebdc7a85 ("bpf: add helper bpf_perf_prog_read_value")
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Function bpf_fill_maxinsns11 is designed to not be able to be JITed on
x86_64. So, it fails when CONFIG_BPF_JIT_ALWAYS_ON=y, and
commit 09584b4067 ("bpf: fix selftests/bpf test_kmod.sh failure when
CONFIG_BPF_JIT_ALWAYS_ON=y") makes sure that failure is detected on that
case.
However, it does not fail on other architectures, which have a different
JIT compiler design. So, test_bpf has started to fail to load on those.
After this fix, test_bpf loads fine on both x86_64 and ppc64el.
Fixes: 09584b4067 ("bpf: fix selftests/bpf test_kmod.sh failure when CONFIG_BPF_JIT_ALWAYS_ON=y")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Fixes: 2f987a76a9 ("net: ipv6: keep sk status consistent after datagram connect failure")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEENrCndlB/VnAEWuH5k9IU1zQoZfEFAlqvjK0THG1rbEBwZW5n
dXRyb25peC5kZQAKCRCT0hTXNChl8ZMKB/4mf5fq7ed4EUKpeu2a6LTxoVl1bMWR
SDwsjVM35x83riG2mctP0TsnZMq16w4PzzDsBERkjBFz2GuiZzfNkpy3dOSR/Y6G
uNl2lJAKJftqJnx7r7qQIfrn0ItAIjGfanGsDI/ZwhiHYM7DGEXbDYUo8BMJAjvW
t9tnqWa6vk7uy2UXxvnLNtqt40EWXL9kKnNjUvL5Ik5g1bKPn9hqcyhKJi48X9Jt
+29MuuLai8dZlpInn9FR/QKZK2Z2ug3Y5oasB9ArNOGDuG7sNAW2gVjpVaZYi3Py
wDUIaQ793FWPBvRm82nj67TomKE06Mm8SDFH1S7TOLEPePfXQwaYzG+1
=kYfz
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.16-20180319' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2018-03-19
this is a pull reqeust of one patch for net/master.
The patch is by Andri Yngvason and fixes a potential use-after-free bug
in the cc770 driver introduced in the previous pull-request.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
cppcheck report:
[drivers/net/ethernet/cortina/gemini.c:543]: (error) Memory leak: skb_tab
Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the optional regulator is deferred, we must release some resources.
They will be re-allocated when the probe function will be called again.
Fixes: 6eacf31139 ("ethernet: arc: Add support for Rockchip SoC layer device tree bindings")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code performs unneeded free. Remove the redundant skb freeing
during the error path.
Fixes: 1555d204e7 ("devlink: Support for pipeline debug (dpipe)")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
Here are a few more important Bluetooth driver fixes for the 4.16
kernel.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko says:
====================
net: phy: relax error checking when creating sysfs link netdev->phydev
Some ethernet drivers (like TI CPSW) may connect and manage >1 Net PHYs per
one netdevice, as result such drivers will produce warning during system
boot and fail to connect second phy to netdevice when PHYLIB framework
will try to create sysfs link netdev->phydev for second PHY
in phy_attach_direct(), because sysfs link with the same name has been
created already for the first PHY.
As result, second CPSW external port will became unusable.
This regression was introduced by commits:
5568363f0c ("net: phy: Create sysfs reciprocal links for attached_dev/phydev"
a399546049 ("net: phy: Relax error checking on sysfs_create_link()"
Patch 1: exports sysfs_create_link_nowarn() function as preparation for Patch 2.
Patch 2: relaxes error checking when PHYLIB framework is creating sysfs
link netdev->phydev in phy_attach_direct(), suppresses warning by using
sysfs_create_link_nowarn() and adds error message instead, so links creation
failure is not fatal any more and system can continue working,
which fixes TI CPSW issue and makes boot logs accessible
in case of NFS boot, for example.
This can be stable material 4.13+.
Changes in v2:
- commit messages updated.
v1:
https://patchwork.ozlabs.org/cover/886058/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ethernet drivers (like TI CPSW) may connect and manage >1 Net PHYs per
one netdevice, as result such drivers will produce warning during system
boot and fail to connect second phy to netdevice when PHYLIB framework
will try to create sysfs link netdev->phydev for second PHY
in phy_attach_direct(), because sysfs link with the same name has been
created already for the first PHY. As result, second CPSW external
port will became unusable.
Fix it by relaxing error checking when PHYLIB framework is creating sysfs
link netdev->phydev in phy_attach_direct(), suppressing warning by using
sysfs_create_link_nowarn() and adding error message instead.
After this change links (phy->netdev and netdev->phy) creation failure is not
fatal any more and system can continue working, which fixes TI CPSW issue.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Fixes: a399546049 ("net: phy: Relax error checking on sysfs_create_link()")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sysfs_create_link_nowarn() is going to be used in phylib framework in
subsequent patch which can be built as module. Hence, export
sysfs_create_link_nowarn() to avoid build errors.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Fixes: a399546049 ("net: phy: Relax error checking on sysfs_create_link()")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes use after free introduced by the last cc770 patch.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Fixes: 746201235b ("can: cc770: Fix queue stall & dropped RTR reply")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When unbinding/removing the driver, we will run into the following warnings:
[ 259.655198] fec 400d1000.ethernet: 400d1000.ethernet supply phy not found, using dummy regulator
[ 259.665065] fec 400d1000.ethernet: Unbalanced pm_runtime_enable!
[ 259.672770] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
[ 259.683062] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: f2:3e:93:b7:29:c1
[ 259.696239] libphy: fec_enet_mii_bus: probed
Avoid these warnings by balancing the runtime PM calls during fec_drv_remove().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
batadv_check_unicast_ttvn may redirect a packet to itself or another
originator. This involves rewriting the ttvn and the destination address in
the batadv unicast header. These field were not yet pulled (with skb rcsum
update) and thus any change to them also requires a change in the receive
checksum.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fixes: a73105b8d4 ("batman-adv: improved client announcement mechanism")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
'Commit 45dac1d6ea ("vmxnet3: Changes for vmxnet3 adapter version 2
(fwd)")' introduced a flag "lro" in structure vmxnet3_adapter which is
used to indicate whether LRO is enabled or not. However, the patch
did not set the flag and hence it was never exercised.
So, when LRO is enabled, it resulted in poor TCP performance due to
delayed acks. This issue is seen with packets which are larger than
the mss getting a delayed ack rather than an immediate ack, thus
resulting in high latency.
This patch removes the lro flag and directly uses device features
against NETIF_F_LRO to check if lro is enabled.
Fixes: 45dac1d6ea ("vmxnet3: Changes for vmxnet3 adapter version 2 (fwd)")
Reported-by: Rachel Lunnon <rachel_lunnon@stormagic.com>
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The field txNumDeferred is used by the driver to keep track of the number
of packets it has pushed to the emulation. The driver increments it on
pushing the packet to the emulation and the emulation resets it to 0 at
the end of the transmit.
There is a possibility of a race either when (a) ESX is under heavy load or
(b) workload inside VM is of low packet rate.
This race results in xmit hangs when network coalescing is disabled. This
change creates a local copy of txNumDeferred and uses it to perform ring
arithmetic.
Reported-by: Noriho Tanaka <ntanaka@vmware.com>
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti says:
====================
net/sched: fix NULL dereference in the error path of .init()
with several TC actions it's possible to see NULL pointer dereference,
when the .init() function calls tcf_idr_alloc(), fails at some point and
then calls tcf_idr_release(): this series fixes all them introducing
non-NULL tests in the .cleanup() function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
