Newer bluetooth stack supports the NO_INIT_REPORTS quirk. The wiimote does not
support report initialization so enable it by default.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The version number is not needed at all for in-tree drivers. Upstream git is
used to track module versions.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Keep track of current drm and add new debugfs file which reads or writes the
current DRM.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote provides direct access to parts of its eeprom. This implements read
support for small chunks of the eeprom. This isn't very fast but prevents the
reader from blocking the wiimote stream for too long.
Write support is not yet supported as the wiimote breaks if we overwrite its
memory. Use hidraw to reverse-engineer the eeprom before implementing write
support here.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add initializer and deinitializer for debugfs support. This will later allow raw
eeprom access and direct DRM modifications to debug wiimote behaviour and
further protocol reverse-engineerings.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Nintendo Classic Controller extension reports lots of keys, two analog sticks
and two analog buttons. We report all data through extension input device to
userspace.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Nintendo Nunchuck extension reports accelerometer values, one analog stick
and two buttons. See inline comments for data layout.
We report all data to userspace through extension input device.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Motion+ reports rotation gyro data which we report to userspace as ABS_RX/Y/Z
values. The device reports them either in fast or slow mode. We adjust the
values to get a linear scale so userspace does not need to know about slow and
fast mode.
The motion+ also reports whether an extension is connected to it. We keep track
of this value and reinitialize the extensions if an extension is plugged or
unplugged.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All supported extensions report data as 6 byte block. All DRMs with extension
data provide at least 6 extension bytes. Hence a generic handler for all
extension bytes is sufficient and can be called on all DRMs.
The handler distinguishes the input and passes it to the right handler. Motion+
passes data interleaved so we can have Motion+ and a regular extension enabled
simultaneously.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Motion+ and regular extensions are physical adapters for the wiimote so create
one input device for each of them. This also allows to enable only opened
extensions and turn unused extenions off to save battery power.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add new sysfs attribute "extension" which returns the currently connected and
initialized extensions.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote extension registers are not fully understood, so we always disable
all extensions on extension-port events. Then we reinitialize and reidentify
them and activate all requested extensions.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add stub functions to read and identify extensions and then initialize all
connected extensions.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote supports several extensions. This adds a separate source file which
handles all extensions and can be disabled at compile-time.
The driver reacts on "plug"-events on the extension port and starts a worker
which initializes or deinitializes the extensions.
Currently, the initialization logic is not fully understood and we can only
detect and enable all extensions when all extensions are deactivated. Therefore,
we need to disable all extensions, then detect and activate them again to react
on "plug"-events.
However, deactivating extensions will generate a new "plug"-event and we will
never leave that loop. Hence, we only support extensions if they are plugged
before the wiimote is connected (or before the ext-input device is opened). In
the future we may support full extension hotplug support, but
reverse-engineering this may take a while.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add helper functions similar to the write-mem helpers but for reading wiimote
memory and eeprom.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wiimote extension and sound support need access to several symbols so move them
into a new header.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Extension and sound support for the wiimote are quite complex and will be
implemented in separate source files. Hence rename the current driver to "-core"
suffix so multiple files can be linked into this module.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
Revert "HID: multitouch: decide if hid-multitouch needs to handle mt devices"
HID: drivers/hid/hid-roccat.c: eliminate a null pointer dereference
HID: hid-apple: add device ID of another wireless aluminium
HID: Add device IDs for Macbook Pro 8 keyboards
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac: (21 commits)
MAINTAINERS: add an entry for Edac Sandy Bridge driver
edac: tag sb_edac as EXPERIMENTAL, as it requires more testing
EDAC: Fix incorrect edac mode reporting in sb_edac
edac: sb_edac: Add it to the building system
edac: Add an experimental new driver to support Sandy Bridge CPU's
i7300_edac: Fix error cleanup logic
i7core_edac: Initialize memory name with cpu, channel, bank
i7core_edac: Fix compilation on 32 bits arch
i7core_edac: scrubbing fixups
EDAC: Correct Kconfig dependencies
i7core_edac: return -ENODEV if no MC is found
i7core_edac: use edac's own way to print errors
MAINTAINERS: remove dropped edac_mce.* from the file
i7core_edac: Drop the edac_mce facility
x86, MCE: Use notifier chain only for MCE decoding
EDAC i7core: Use mce socketid for better compatibility
i7core_edac: Don't enable memory scrubbing for Xeon 35xx
i7core_edac: Add scrubbing support
edac: Move edac main structs to include/linux/edac.h
i7core_edac: Fix oops when trying to inject errors
...
* 'misc-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
MAINTAINERS: Update entry for IA64
[IA64] gpio: GENERIC_GPIO default must be n
[IA64[ add CONFIG_NET_VENDOR_INTEL=y to default config files where needed
[IA64] agp/hp-agp: Allow binding user memory to the AGP GART
[IA64] sn2: add missing put_cpu()
Says Andrew:
"60 patches. That's good enough for -rc1 I guess. I have quite a lot
of detritus to be rechecked, work through maintainers, etc.
- most of the remains of MM
- rtc
- various misc
- cgroups
- memcg
- cpusets
- procfs
- ipc
- rapidio
- sysctl
- pps
- w1
- drivers/misc
- aio"
* akpm: (60 commits)
memcg: replace ss->id_lock with a rwlock
aio: allocate kiocbs in batches
drivers/misc/vmw_balloon.c: fix typo in code comment
drivers/misc/vmw_balloon.c: determine page allocation flag can_sleep outside loop
w1: disable irqs in critical section
drivers/w1/w1_int.c: multiple masters used same init_name
drivers/power/ds2780_battery.c: fix deadlock upon insertion and removal
drivers/power/ds2780_battery.c: add a nolock function to w1 interface
drivers/power/ds2780_battery.c: create central point for calling w1 interface
w1: ds2760 and ds2780, use ida for id and ida_simple_get() to get it
pps gpio client: add missing dependency
pps: new client driver using GPIO
pps: default echo function
include/linux/dma-mapping.h: add dma_zalloc_coherent()
sysctl: make CONFIG_SYSCTL_SYSCALL default to n
sysctl: add support for poll()
RapidIO: documentation update
drivers/net/rionet.c: fix ethernet address macros for LE platforms
RapidIO: fix potential null deref in rio_setup_device()
RapidIO: add mport driver for Tsi721 bridge
...
In vmballoon_reserve_page(), flags has been passed from the callee
function (vmballoon_inflate here). So, we can determine can_sleep outside
the loop.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Interrupting w1_delay() in w1_read_bit() results in missing the low level
on the w1 line and receiving "1" instead of "0".
Add local_irq_save()/local_irq_restore() around the critical section
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds a nolock function to the w1 interface to avoid locking the
mutex if needed.
Signed-off-by: Clifton Barnes <cabarnes@indesign-llc.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: <stable@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Straightforward. As an aside, the ida_init calls are not needed as far as
I can see needed. (DEFINE_IDA does the same already).
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Clifton Barnes <cabarnes@indesign-llc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add "depends on GENERIC_HARDIRQS" to avoid compile breakage on s390:
drivers/built-in.o: In function `pps_gpio_remove':
linux-next/drivers/pps/clients/pps-gpio.c:189: undefined reference to `free_irq'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: James Nuss <jamesnuss@nanometrics.ca>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This client driver allows you to use a GPIO pin as a source for PPS
signals. Platform data [1] are used to specify the GPIO pin number,
label, assert event edge type, and whether clear events are captured.
This driver is based on the work by Ricardo Martins who submitted an
initial implementation [2] of a PPS IRQ client driver to the linuxpps
mailing-list on Dec 3 2010.
[1] include/linux/pps-gpio.h
[2] http://ml.enneenne.com/pipermail/linuxpps/2010-December/004155.html
[akpm@linux-foundation.org: remove unneeded cast of void*]
Signed-off-by: James Nuss <jamesnuss@nanometrics.ca>
Cc: Ricardo Martins <rasm@fe.up.pt>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Ricardo Martins <rasm@fe.up.pt>
Cc: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Cc: Igor Plyatov <plyatov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A default echo function has been provided so it is no longer an error when
you specify PPS_ECHOASSERT or PPS_ECHOCLEAR without an explicit echo
function. This allows some code re-use and also makes it easier to write
client drivers since the default echo function does not normally need to
change.
Signed-off-by: James Nuss <jamesnuss@nanometrics.ca>
Reviewed-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Cc: Ricardo Martins <rasm@fe.up.pt>
Cc: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Cc: Igor Plyatov <plyatov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify Ethernet addess macros to be compatible with BE/LE platforms
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Chul Kim <chul.kim@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: <stable@kernel.org> [2.6.39+]
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "goto cleanup" path can deference "rswitch" when it is NULL.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Chul Kim <chul.kim@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add RapidIO mport driver for IDT TSI721 PCI Express-to-SRIO bridge device.
The driver provides full set of callback functions defined for mport
devices in RapidIO subsystem. It also is compatible with current version
of RIONET driver (Ethernet over RapidIO messaging services).
This patch is applicable to kernel versions starting from 2.6.39.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Chul Kim <chul.kim@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The discovered bit in PGCCSR register indicates if the device has been
discovered by system host. In Rapidio systems, some agent devices can also
be master devices. They can issue requests into the system.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver is added using platform_driver_probe(), so the callbacks can be
discarded more aggessively.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add initial support for the microchip mcp7941x series of real time clocks.
The mcp7941x series is generally compatible with the ds1307 and ds1337 rtc
devices from dallas semiconductor. minor differences include a backup
battery enable bit, and the polarity of the oscillator enable bit.
Signed-off-by: David Anders <danders.dev@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the one use of an ida that doesn't retry on receiving -EAGAIN.
I'm assuming do so will cause no harm and may help on a rare occasion.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://github.com/rustyrussell/linux:
virtio-blk: use ida to allocate disk index
virtio: Add platform bus driver for memory mapped virtio device
virtio: Dont add "config" to list for !per_vq_vector
virtio: console: wait for first console port for early console output
virtio: console: add port stats for bytes received, sent and discarded
virtio: console: make discard_port_data() use get_inbuf()
virtio: console: rename variable
virtio: console: make get_inbuf() return port->inbuf if present
virtio: console: Fix return type for get_inbuf()
virtio: console: Use wait_event_freezable instead of _interruptible
virtio: console: Ignore port name update request if name already set
virtio: console: Fix indentation
virtio: modify vring_init and vring_size to take account of the layout containing *_event_idx
virtio.h: correct comment for struct virtio_driver
virtio-net: Use virtio_config_val() for retrieving config
virtio_config: Add virtio_config_val_len()
virtio-console: Use virtio_config_val() for retrieving config
* 'for-linus' of git://github.com/richardweinberger/linux: (90 commits)
um: fix ubd cow size
um: Fix kmalloc argument order in um/vdso/vma.c
um: switch to use of drivers/Kconfig
UserModeLinux-HOWTO.txt: fix a typo
UserModeLinux-HOWTO.txt: remove ^H characters
um: we need sys/user.h only on i386
um: merge delay_{32,64}.c
um: distribute exports to where exported stuff is defined
um: kill system-um.h
um: generic ftrace.h will do...
um: segment.h is x86-only and needed only there
um: asm/pda.h is not needed anymore
um: hw_irq.h can go generic as well
um: switch to generic-y
um: clean Kconfig up a bit
um: a couple of missing dependencies...
um: kill useless argument of free_chan() and free_one_chan()
um: unify ptrace_user.h
um: unify KSTK_...
um: fix gcov build breakage
...
* kill duplicates with drivers/char/Kconfig
* take watchdog one into drivers/watchdog/Kconfig
* take mmapper to arch/um/Kconfig.um
* rename Kconfig.char menu to "UML Character Devices"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Replace remaining direct i_nlink updates with a new set_nlink()
updater function.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Tested-by: Toshiyuki Okajima <toshi.okajima@jp.fujitsu.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Replace direct i_nlink updates with the respective updater function
(inc_nlink, drop_nlink, clear_nlink, inode_dec_link_count).
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
* 'next/dt' of git://git.linaro.org/people/arnd/arm-soc:
ARM: gic: use module.h instead of export.h
ARM: gic: fix irq_alloc_descs handling for sparse irq
ARM: gic: add OF based initialization
ARM: gic: add irq_domain support
irq: support domains with non-zero hwirq base
of/irq: introduce of_irq_init
ARM: at91: add at91sam9g20 and Calao USB A9G20 DT support
ARM: at91: dt: at91sam9g45 family and board device tree files
arm/mx5: add device tree support for imx51 babbage
arm/mx5: add device tree support for imx53 boards
ARM: msm: Add devicetree support for msm8660-surf
msm_serial: Add devicetree support
msm_serial: Use relative resources for iomem
Fix up conflicts in arch/arm/mach-at91/{at91sam9260.c,at91sam9g45.c}
* 'next/cleanup2' of git://git.linaro.org/people/arnd/arm-soc: (31 commits)
ARM: OMAP: Warn if omap_ioremap is called before SoC detection
ARM: OMAP: Move set_globals initialization to happen in init_early
ARM: OMAP: Map SRAM later on with ioremap_exec()
ARM: OMAP: Remove calls to SRAM allocations for framebuffer
ARM: OMAP: Avoid cpu_is_omapxxxx usage until map_io is done
ARM: OMAP1: Use generic map_io, init_early and init_irq
arm/dts: OMAP3+: Add mpu, dsp and iva nodes
arm/dts: OMAP4: Add a main ocp entry bound to l3-noc driver
ARM: OMAP2+: l3-noc: Add support for device-tree
ARM: OMAP2+: board-generic: Add i2c static init
ARM: OMAP2+: board-generic: Add DT support to generic board
arm/dts: Add support for OMAP3 Beagle board
arm/dts: Add initial device tree support for OMAP3 SoC
arm/dts: Add support for OMAP4 SDP board
arm/dts: Add support for OMAP4 PandaBoard
arm/dts: Add initial device tree support for OMAP4 SoC
ARM: OMAP: omap_device: Add a method to build an omap_device from a DT node
ARM: OMAP: omap_device: Add omap_device_[alloc|delete] for DT integration
of: Add helpers to get one string in multiple strings property
ARM: OMAP2+: devices: Remove all omap_device_pm_latency structures
...
Fix up trivial header file conflicts in arch/arm/mach-omap2/board-generic.c
