This reverts commit 55aedef50d.
Commit 55aedef50d ("pinctrl: intel: Do pin translation when lock IRQ")
added special translation from GPIO number to hardware pin number to
irq_reqres/relres hooks to avoid failure when IRQs are requested. The
actual failure happened inside gpiochip_lock_as_irq() because it calls
gpiod_get_direction() and pinctrl-intel.c::intel_gpio_get_direction()
implementation originally missed the translation so the two hooks made
it work by skipping the ->get_direction() call entirely (it overwrote
the default GPIOLIB provided functions).
The proper fix that adds translation to GPIO callbacks was merged with
commit 96147db1e1 ("pinctrl: intel: Do pin translation in other GPIO
operations as well"). This allows us to use the default GPIOLIB provided
functions again.
In addition as find out by Benjamin Tissoires the two functions
(intel_gpio_irq_reqres()/intel_gpio_irq_relres()) now cause problems of
their own because they operate on pin numbers and pass that pin number
to gpiochip_lock_as_irq() which actually expects a GPIO number.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199911
Fixes: 55aedef50d ("pinctrl: intel: Do pin translation when lock IRQ")
Reported-and-tested-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It turns out the HOSTSW_OWN register offset is different between LP and
H variants. The latter should use 0xc0 instead so fix that.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199911
Fixes: a663ccf0fe ("pinctrl: intel: Add Intel Cannon Lake PCH-H pin controller support")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
From the AMD BKDG, if WAKE_INT_MASTER_REG.MaskStsEn is set, a software
write to the debounce registers of *any* gpio will block wake/interrupt
status generation for *all* gpios for a length of time that depends on
WAKE_INT_MASTER_REG.MaskStsLength[11:0]. During this period the Interrupt
Delivery bit (INTERRUPT_ENABLE) will read as 0.
In commit 4c1de0414a ("pinctrl/amd: poll InterruptEnable bits in
enable_irq") we tried to fix this same "gpio Interrupts are blocked
immediately after writing debounce registers" problem, but incorrectly
assumed it only affected the gpio whose debounce was being configured
and not ALL gpios.
To solve this for all gpios, we move the polling loop from
amd_gpio_irq_enable() to amd_gpio_irq_set_type(), while holding the gpio
spinlock. This ensures that another gpio operation (e.g.
amd_gpio_irq_unmask()) can read a temporarily disabled IRQ and
incorrectly disable it while trying to modify some other register bits.
Fixes: 4c1de0414a pinctrl/amd: poll InterruptEnable bits in enable_irq
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For some reason I thought GPIOLIB handles translation from GPIO ranges
to pinctrl pins but it turns out not to be the case. This means that
when GPIOs operations are performed for a pin controller having a custom
GPIO base such as Cannon Lake and Ice Lake incorrect pin number gets
used internally.
Fix this in the same way we did for lock/unlock IRQ operations and
translate the GPIO number to pin before using it.
Fixes: a60eac3239 ("pinctrl: intel: Allow custom GPIO base for pad groups")
Reported-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio base for GPP-E was set incorrectly to 258 instead of 256,
preventing the touchpad working on my Tong Fang GK5CN5Z laptop.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=200787
Signed-off-by: Simon Detheridge <s@sd.ai>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If we are being configured via pdata we don't necessarily have
any gpio mappings being configured that way so pdata->gpio_config
could be NULL.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit a203728ac6 ("pinctrl: core: Return selector to the pinctrl
driver") and commit f913cfce4e ("pinctrl: pinmux: Return selector to
the pinctrl driver") modified the return values of
pinctrl_generic_add_group() and pinmux_generic_add_function()
respectively, but did so without updating their callers. This broke the
pinctrl-ingenic driver, which treats non-zero return values from these
functions as errors & fails to probe. For example on a MIPS Ci20:
pinctrl-ingenic 10010000.pin-controller: Failed to register group uart0-hwflow
pinctrl-ingenic: probe of 10010000.pin-controller failed with error 1
Without the pinctrl driver probed, other drivers go on to fail to probe
too & the system is unusable.
Fix this by modifying the error checks to treat only negative values as
errors, matching the commits that introduced the breakage & similar
changes made to other drivers.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: a203728ac6 ("pinctrl: core: Return selector to the pinctrl driver")
Fixes: f913cfce4e ("pinctrl: pinmux: Return selector to the pinctrl driver")
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt controller hardware in this pin controller has two status
enable bits. The first "normal" status enable bit enables or disables
the summary interrupt line being raised when a gpio interrupt triggers
and the "raw" status enable bit allows or prevents the hardware from
latching an interrupt into the status register for a gpio interrupt.
Currently we just toggle the "normal" status enable bit in the mask and
unmask ops so that the summary irq interrupt going to the CPU's
interrupt controller doesn't trigger for the masked gpio interrupt.
For a level triggered interrupt, the flow would be as follows: the pin
controller sees the interrupt, latches the status into the status
register, raises the summary irq to the CPU, summary irq handler runs
and calls handle_level_irq(), handle_level_irq() masks and acks the gpio
interrupt, the interrupt handler runs, and finally unmask the interrupt.
When the interrupt handler completes, we expect that the interrupt line
level will go back to the deasserted state so the genirq code can unmask
the interrupt without it triggering again.
If we only mask the interrupt by clearing the "normal" status enable bit
then we'll ack the interrupt but it will continue to show up as pending
in the status register because the raw status bit is enabled, the
hardware hasn't deasserted the line, and thus the asserted state latches
into the status register again. When the hardware deasserts the
interrupt the pin controller still thinks there is a pending unserviced
level interrupt because it latched it earlier. This behavior causes
software to see an extra interrupt for level type interrupts each time
the interrupt is handled.
Let's fix this by clearing the raw status enable bit for level type
interrupts so that the hardware stops latching the status of the
interrupt after we ack it. We don't do this for edge type interrupts
because it seems that toggling the raw status enable bit for edge type
interrupts causes spurious edge interrupts.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
- New Device Support
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
- New Functionality
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
- Fix-ups
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
- Bug Fixes
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501
-----BEGIN PGP SIGNATURE-----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=4Yj4
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
mfd: bd71837: Core driver for ROHM BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
Here are all of the driver core and related patches for 4.19-rc1.
Nothing huge here, just a number of small cleanups and the ability to
now stop the deferred probing after init happens.
All of these have been in linux-next for a while with only a merge issue
reported. That merge issue is in fs/sysfs/group.c and Stephen has
posted the diff of what it should be to resolve this. I'll follow up
with that diff to this pull request.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g86Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynyXQCePaZSW8wft4b7nLN8RdZ98ATBru0Ani10lrJa
HQeQJRNbWU1AZ0ym7695
=tOaH
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are all of the driver core and related patches for 4.19-rc1.
Nothing huge here, just a number of small cleanups and the ability to
now stop the deferred probing after init happens.
All of these have been in linux-next for a while with only a merge
issue reported"
* tag 'driver-core-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (21 commits)
base: core: Remove WARN_ON from link dependencies check
drivers/base: stop new probing during shutdown
drivers: core: Remove glue dirs from sysfs earlier
driver core: remove unnecessary function extern declare
sysfs.h: fix non-kernel-doc comment
PM / Domains: Stop deferring probe at the end of initcall
iommu: Remove IOMMU_OF_DECLARE
iommu: Stop deferring probe at end of initcalls
pinctrl: Support stopping deferred probe after initcalls
dt-bindings: pinctrl: add a 'pinctrl-use-default' property
driver core: allow stopping deferred probe after init
driver core: add a debugfs entry to show deferred devices
sysfs: Fix internal_create_group() for named group updates
base: fix order of OF initialization
linux/device.h: fix kernel-doc notation warning
Documentation: update firmware loader fallback reference
kobject: Replace strncpy with memcpy
drivers: base: cacheinfo: use OF property_read_u32 instead of get_property,read_number
kernfs: Replace strncpy with memcpy
device: Add #define dev_fmt similar to #define pr_fmt
...
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Core changes:
- Augment pinctrl_generic_add_group() and pinmux_generic_add_function()
to return the selector for the added group/function to the caller
and augment (hopefully) all drivers to handle this.
New subdrivers:
- Qualcomm PM8998 and PM8005 are supported in the SPMI pin
control and GPIO driver.
- Intel Ice Lake PCH (platform controller hub) support.
- NXP (ex Freescale) i.MX8MQ support.
- Berlin AS370 support.
Improvements to drivers:
- Support interrupts on the Ocelot pin controller.
- Add SPI pins to the Uniphier driver.
- Define a GPIO compatible per SoC in the Tegra driver.
- Push Tegra initialization down in the initlevels.
- Support external wakeup interrupts on the Exynos.
- Add generic clocks pins to the meson driver.
- Add USB and HSCIF pins for some Renesas PFC chips.
- Suspend/resume support in the armada-37xx.
- Interrupt support for the Actions Semiconductor S900 also
known as "owl".
- Correct the pin ordering in Cedarfork.
- Debugfs output for INTF in the mcp23s08 driver
- Avoid divisions in context save/restore in pinctrl-single.
The rest is minor bug fixes or cleanups.
-----BEGIN PGP SIGNATURE-----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=EUMW
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for v4.19:
Core changes:
- Augment pinctrl_generic_add_group() and pinmux_generic_add_function()
to return the selector for the added group/function to the caller
and augment (hopefully) all drivers to handle this
New subdrivers:
- Qualcomm PM8998 and PM8005 are supported in the SPMI pin control
and GPIO driver
- Intel Ice Lake PCH (platform controller hub) support
- NXP (ex Freescale) i.MX8MQ support
- Berlin AS370 support
Improvements to drivers:
- Support interrupts on the Ocelot pin controller
- Add SPI pins to the Uniphier driver
- Define a GPIO compatible per SoC in the Tegra driver
- Push Tegra initialization down in the initlevels
- Support external wakeup interrupts on the Exynos
- Add generic clocks pins to the meson driver
- Add USB and HSCIF pins for some Renesas PFC chips
- Suspend/resume support in the armada-37xx
- Interrupt support for the Actions Semiconductor S900 also known as
"owl"
- Correct the pin ordering in Cedarfork
- Debugfs output for INTF in the mcp23s08 driver
- Avoid divisions in context save/restore in pinctrl-single
The rest is minor bug fixes or cleanups"
* tag 'pinctrl-v4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (69 commits)
pinctrl: nomadik: silence uninitialized variable warning
pinctrl: axp209: Fix NULL pointer dereference after allocation
pinctrl: samsung: Remove duplicated "wakeup" in printk
pinctrl: ocelot: add support for interrupt controller
pinctrl: intel: Don't shadow error code of gpiochip_lock_as_irq()
pinctrl: berlin: fix 'pctrl->functions' allocation in berlin_pinctrl_build_state
gpio: tegra: Move driver registration to subsys_init level
pinctrl: tegra: Move drivers registration to arch_init level
pinctrl: baytrail: actually print the apparently misconfigured pin
MAINTAINERS: Replace Heikki as maintainer of Intel pinctrl
pinctrl: freescale: off by one in imx1_pinconf_group_dbg_show()
pinctrl: uniphier: add spi pin-mux settings
pinctrl: cannonlake: Fix community ordering for H variant
pinctrl: tegra: define GPIO compatible node per SoC
pinctrl: intel: Do pin translation when lock IRQ
pinctrl: imx: off by one in imx_pinconf_group_dbg_show()
pinctrl: mediatek: include chained_irq.h header
pinctrl/amd: only handle irq if it is pending and unmasked
pinctrl/amd: fix gpio irq level in debugfs
pinctrl: stm32: add syscfg mask parameter
...
This is harmless, but "val" isn't necessarily initialized if
abx500_get_register_interruptible() fails. I've re-arranged the code to
just return an error code in that situation.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no check that allocation in axp20x_funcs_groups_from_mask
is successful.
The patch adds corresponding check and return values.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This GPIO controller can serve as an interrupt controller as well on the
GPIOs it handles.
An interrupt is generated whenever a GPIO line changes and the
interrupt for this GPIO line is enabled. This means that both the
changes from low to high and high to low generate an interrupt.
For some use cases, it makes sense to ignore the high to low change and
not generate an interrupt. Such a use case is a line that is hold in a
level high/low manner until the event holding the line gets acked.
This can be achieved by making sure the interrupt on the GPIO controller
side gets acked and masked only after the line gets hold in its default
state, this is what's done with the fasteoi functions.
Only IRQ_TYPE_EDGE_BOTH and IRQ_TYPE_LEVEL_HIGH are supported for now.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_lock_as_irq() may return a few error codes,
do not shadow them by -EINVAL and let caller to decide.
No functional change intended.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
fixes following Smatch static check warning:
drivers/pinctrl/berlin/berlin.c:237 berlin_pinctrl_build_state()
warn: passing devm_ allocated variable to kfree. 'pctrl->functions'
As we will be calling krealloc() on pointer 'pctrl->functions', which means
kfree() will be called in there, devm_kzalloc() shouldn't be used with
the allocation in the first place. Fix the warning by calling kcalloc()
and managing the free procedure in error path on our own.
Fixes: 3de68d331c ("pinctrl: berlin: add the core pinctrl driver for Marvell Berlin SoCs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a bug in regards to deferred probing within the drivers core
that causes GPIO-driver to suspend after its users. The bug appears if
GPIO-driver probe is getting deferred, which happens after introducing
dependency on PINCTRL-driver for the GPIO-driver by defining "gpio-ranges"
property in device-tree. The bug in the drivers core is old (more than 4
years now) and is well known, unfortunately there is no easy fix for it.
The good news is that we can workaround the deferred probe issue by
changing GPIO / PINCTRL drivers registration order and hence by moving
PINCTRL driver registration to the arch_init level and GPIO to the
subsys_init.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For further investigation the actual result in interrupt status register
is needed.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The info->groups[] array is allocated in imx1_pinctrl_parse_dt(). It
has info->ngroups elements. Thus the > here should be >= to prevent
reading one element beyond the end of the array.
Cc: stable@vger.kernel.org
Fixes: 30612cd900 ("pinctrl: imx1 core driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Uwe Kleine-König <u.kleine-könig@pengutronix.de>
Acked-by: Dong Aisheng <Aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver was written based on an assumption that BIOS provides
unordered communities in ACPI DSDT. Nevertheless, it seems that
BIOS getting fixed before being provisioned to OxM:s.
So does driver.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199911
Reported-by: Marc Landolt <2009@marclandolt.ch>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: a663ccf0fe ("pinctrl: intel: Add Intel Cannon Lake PCH-H pin controller support")
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra 2 uses a different GPIO controller which uses "tegra20-gpio" as
compatible string.
Make the compatible string the GPIO node is using a SoC specific
property. This prevents the kernel from registering the GPIO range
twice in case the GPIO range is specified in the device tree.
Fixes: 9462510ce3 ("pinctrl: tegra: Only set the gpio range if needed")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Default GPIOLIB callbacks for request and release IRQ do not do a GPIO
to pin translation which is necessary for Intel hardware, such as Intel
Cannonlake. Absence of the translation prevents some pins to be locked
as IRQ due to direction check. Introduce own callbacks to make
translation possible to avoid above issue.
Fixes: a60eac3239 ("pinctrl: intel: Allow custom GPIO base for pad groups")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The > should really be >= here. It's harmless because
pinctrl_generic_get_group() will return a NULL if group is invalid.
Fixes: ae75ff8145 ("pinctrl: pinctrl-imx: add imx pinctrl core driver")
Reported-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some randconfig builds fail in the mtk-eint driver:
drivers/pinctrl/mediatek/mtk-eint.c: In function 'mtk_eint_irq_handler':
drivers/pinctrl/mediatek/mtk-eint.c:324:2: error: implicit declaration of function 'chained_irq_enter'; did you mean 'rcu_irq_enter'? [-Werror=implicit-function-declaration]
chained_irq_enter(chip, desc);
^~~~~~~~~~~~~~~~~
rcu_irq_enter
drivers/pinctrl/mediatek/mtk-eint.c:367:2: error: implicit declaration of function 'chained_irq_exit'; did you mean 'rcu_irq_exit'? [-Werror=implicit-function-declaration]
The functions are declared in linux/irqchip/chained_irq.h, and including
that header makes it build in all configurations.
Fixes: e46df235b4 ("pinctrl: mediatek: refactor EINT related code for all MediaTek pinctrl can fit")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AMD pinctrl driver demultiplexes GPIO interrupts and fires off their
individual handlers.
If one of these GPIO irqs is configured as a level interrupt, and its
downstream handler is a threaded ONESHOT interrupt, the GPIO interrupt
source is masked by handle_level_irq() until the eventual return of the
threaded irq handler. During this time the level GPIO interrupt status
will still report as high until the actual gpio source is cleared - both
in the individual GPIO interrupt status bit (INTERRUPT_STS_OFF) and in
its corresponding "WAKE_INT_STATUS_REG" bit.
Thus, if another GPIO interrupt occurs during this time,
amd_gpio_irq_handler() will see that the (masked-and-not-yet-cleared)
level irq is still pending and incorrectly call its handler again.
To fix this, have amd_gpio_irq_handler() check for both interrupts status
and mask before calling generic_handle_irq().
Note: Is it possible that this bug was the source of the interrupt storm
on Ryzen when using chained interrupts before commit ba714a9c1d
("pinctrl/amd: Use regular interrupt instead of chained")?
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to the AMD BKDG, the GPIO ActiveLevel bits (10:9) map to:
00 Active High
01 Active Low
10 Active on both edges iff LevelTrig (bit 8) == 0
11 Reserved
The current code has a bug where it interprets 00 => Active Low, and
01 => Active High.
Fix the bug, restrict "Active on both" to just the edge trigger case, and
refactor a bit to make the logic more readable.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds mask parameter to define IRQ mux field.
This field could vary depend of IRQ mux selection register.
To avoid backward compatibility, the drivers set
the legacy value by default.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Register a new GPIO bank only if GPIO bank node is enabled. This patch also
adds checks on ranges which are defined only if a bank is registered.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case the exti line is not in line with the bank number (that is the case
when there is an hole between two banks, for example GPIOK and then GPIOZ),
use "st,bank-ioport" DT property to get the right exti line.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pin-controller driver for Synaptics AS370 SoC, with definition
of its groups and functions. This uses the core Berlin pinctrl driver.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Immutable Branch which moves the cros_ec_i2c and cros_ec_spi
transport drivers from mfd to platform/chrome. Changes in arm are a simple
rename in defconfigs. Change in input is a rename in help text.
-----BEGIN PGP SIGNATURE-----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=EhHj
-----END PGP SIGNATURE-----
Merge branches 'ib-mfd-4.19', 'ib-mfd-gpio-pinctrl-4.19', 'ib-mfd-i915-media-platform-4.19' and 'ib-mfd-regulator-4.19', tag 'ib-platform-chrome-mfd-move-cros-ec-transport-for-4.19' into ibs-for-mfd-merged
Immutable branch (mfd, chrome) due for the v4.19 window
Immutable Branch which moves the cros_ec_i2c and cros_ec_spi
transport drivers from mfd to platform/chrome. Changes in arm are a simple
rename in defconfigs. Change in input is a rename in help text.
1. Add handling of external wakeup interrupts mask inside the pin
controller driver.
Existing solution is spread between the driver and machine code. The
machine code writes the mask but its value is taken from pin
controller driver.
This moves everything into pin controller driver allowing later to
remove the cross-subsystem interaction. Also this is a necessary
step for implementing later Suspend to RAM on ARMv8 Exynos5433.
2. Bring necessary suspend/resume callbacks for Exynos542x and
Exynos5260.
3. Document hidden requirement about one external wakeup interrupts
device node.
4. Minor documentation cleanups.
-----BEGIN PGP SIGNATURE-----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=a9XD
-----END PGP SIGNATURE-----
Merge tag 'samsung-pinctrl-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/samsung into devel
Samsung pinctrl drivers changes for v4.19
1. Add handling of external wakeup interrupts mask inside the pin
controller driver.
Existing solution is spread between the driver and machine code. The
machine code writes the mask but its value is taken from pin
controller driver.
This moves everything into pin controller driver allowing later to
remove the cross-subsystem interaction. Also this is a necessary
step for implementing later Suspend to RAM on ARMv8 Exynos5433.
2. Bring necessary suspend/resume callbacks for Exynos542x and
Exynos5260.
3. Document hidden requirement about one external wakeup interrupts
device node.
4. Minor documentation cleanups.
The pinctrl driver defines an IRQ chip which handles external wakeup
interrupts, therefore from logical point of view, it is the owner of
external interrupt mask. The register controlling the mask belongs to
Power Management Unit address space so it has to be accessed with PMU
syscon regmap handle.
This mask should be written to hardware during system suspend. Till now
ARMv7 machine code was responsible for this which created a dependency
between pin controller driver and arch/arm/mach code.
Try to rework this dependency so the pinctrl driver will write external
wakeup interrupt mask during late suspend.
Impact on ARMv7 designs (S5Pv210 and Exynos)
============================================
This duplicates setting mask with existing machine code
arch/arm/mach-exynos/suspend.c and arch/arm/mach-s5pv210/pm.c but it is
not a problem - the wakeup mask register will be written twice. The
machine code will be cleaned up later.
The difference between implementation here and ARMv7 machine code
(arch/arm/mach-*) is the time of writing the mask:
1. The machine code is writing the mask quite late during system suspend
path, after offlining secondary CPUs and just before doing actual
suspend.
2. The implementation in pinctrl driver uses late suspend ops, therefore it
will write the mask much earlier. Hopefully late enough, after all
drivers will enable or disable their interrupt wakeups
(enable_irq_wake() etc).
Impact on ARMv8 designs (Exynos5433 and Exynos7)
================================================
The Suspend to RAM was not supported and external wakeup interrupt mask
was not written to HW. This change brings us one step closer to
supporting Suspend to RAM.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
The S5Pv210 external wakeup interrupts differ from Exynos therefore
separate compatible is needed. Duplicate existing flavor specific data
from exynos4210_wkup_irq_chip and add new compatible for S5Pv210.
At this point this new compatible does not bring anything new and works
exactly as existing "samsung,exynos4210-wakeup-eint".
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Add missing documentation for suspend and resume members of struct
samsung_pin_ctrl and samsung_pinctrl_drv_data.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Suspend and resume callbacks in Exynos/S5Pv210 pin controller drivers,
save and restore state of registers. This operations should be done for
all banks which have external interrupts (as denoted by using
EXYNOS_PIN_BANK_EINTG/EINTW macros).
Add all banks of Exynos5260 and Exynos5420. This is necessary step for
supporting suspend to RAM on these SoCs.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
After the commit acf137951367 ("pinctrl: core: Return selector to the
pinctrl driver") and the commit 47f1242d19c3 ("pinctrl: pinmux: Return
selector to the pinctrl driver"), it's necessary to add the fixes
needed for the pin controller drivers to use the appropriate returned
selector for a negative error number returned in case of the fail at
these functions. Otherwise, the driver would have a failed probe and
that causes boot message cannot correctly output and devices fail
to acquire their own pins.
Cc: Kevin Hilman <khilman@baylibre.com>
Fixes: acf137951367 ("pinctrl: core: Return selector to the pinctrl driver")
Fixes: 47f1242d19c3 ("pinctrl: pinmux: Return selector to the pinctrl driver")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the missing unlock before return from function
in the error handling case.
Fixes: 0f5972033509 ("pinctrl: single: Fix group and function selector use")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With no users left for these functions let's remove them.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Christ van Willegen <cvwillegen@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-By: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We must use a mutex around the generic_add functions and save the
function and group selector in case we need to remove them. Otherwise
the selector use will be racy for deferred probe at least.
Fixes: 5a49b644b3 ("pinctrl: Renesas RZ/A1 pin and gpio controller")
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Christ van Willegen <cvwillegen@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Sean Wang <sean.wang@mediatek.com>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-By: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We must use a mutex around the generic_add functions and save the
function and group selector in case we need to remove them. Otherwise
the selector use will be racy for deferred probe at least.
Note that struct device_node *np is unused in pcs_add_function() we
remove that too and fix a checkpatch warning for bare unsigned while
at it.
Fixes: 571aec4df5 ("pinctrl: single: Use generic pinmux helpers for
managing functions")
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Christ van Willegen <cvwillegen@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-By: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We must return the selector from pinmux_generic_add_function() so
pin controller device drivers can remove the right group if needed
for deferred probe for example. And we now must make sure that a
proper name is passed so we can use it to check if the entry already
exists.
Note that fixes are also needed for the pin controller drivers to
use the selector value.
Fixes: a76edc89b1 ("pinctrl: core: Add generic pinctrl functions for
managing groups")
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Christ van Willegen <cvwillegen@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-By: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We must return the selector from pinctrl_generic_add_group() so
pin controller device drivers can remove the right group if needed
for deferred probe for example. And we now must make sure that a
proper name is passed so we can use it to check if the entry already
exists.
Note that fixes are also needed for the pin controller drivers to
use the selector value.
Fixes: c7059c5ac7 ("pinctrl: core: Add generic pinctrl functions
for managing groups")
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Christ van Willegen <cvwillegen@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-By: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the TWI function on GPIO4 is actually a multiplexed SCL, not an original
TWI SDA or SCL. Fix it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The i.MX8MQ pincontrol works in a similar way to the earlier i.MX SoCs.
This driver builds on top of the imx specific pinconf handling.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
