Commit Graph

29598 Commits

Author SHA1 Message Date
Marcel Holtmann
b4cb9fb25e Bluetooth: Read number of supported IAC on controller setup
When initializing a controller make sure to read out the number of
supported IAC and store its result. This value is needed to determine
if limited discoverable for BR/EDR can be configured or not.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-10-14 19:31:12 -03:00
Marcel Holtmann
899e107577 Bluetooth: Check that scan window is smaller or equal than scan interval
The scan window parameter for connection establishment and passive
scanning needs to be smaller or equal than the scan interval.

Instead of waiting for a controller to reject these values later on,
just reject them right away.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-14 21:35:47 +03:00
Johan Hedberg
1f209383f2 Bluetooth: Check that bind() bdaddr type matches connect()
If a socket was bound to an address type other than BR/EDR (such as LE)
we should reject trying to connect it to a BR/EDR address. The same
applies for binding to BR/EDR and trying to connect to non-BR/EDR.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-14 11:26:21 -07:00
Johan Hedberg
80c1a2e76d Bluetooth: Reject invalid bdaddr types for sockets
We need to verify that the bdaddr type passed to connect() and bind() is
within the set of valid values. If it is not we need to cleanly fail
with EINVAL.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-14 11:26:21 -07:00
Johan Hedberg
bfaf8c9ff1 Bluetooth: Convert Set Discoverable to use an asynchronous request
This patch converts Set Discoverable to use an asynchronous request
along with its own completion callback. This is necessary for splitting
raw HCI socket use cases from mgmt, as well as for enabling the hooking
up of Advertising parameters together with the HCI_DISCOVERABLE flag
(coming in later patches).

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-14 11:23:29 -07:00
Johan Hedberg
aa8af46e90 Bluetooth: Fix updating scan mode in set_bredr()
Now that the connectable setting is also applicable for the LE side it's
possible that the HCI_CONNECTABLE flag is already set when changing the
BR/EDR setting from false to true while the controller is powered. In
this situation we need to update the BR/EDR scan mode to reflect the
setting. Additionally, since HCI_CONNECTABLE also applies to LE we must
not clear the HCI_CONNECTABLE flag when disabling bredr.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-14 11:23:28 -07:00
Johan Hedberg
67e5a7a3d7 Bluetooth: Move set_bredr_scan() to avoid forward declaration
The set_bredr_scan() function will soon be needed by the set_bredr()
function, so move it to a new location to avoid having to add a forward
declaration.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-14 11:23:28 -07:00
Johan Hedberg
1987fdc77f Bluetooth: Make Set Connectable also update the LE advertising type
This patch updates the Set Connectable Management command to also update
the LE advertising type to either connectable or non-connectable
advertising. An extra helper function is needed for getting the right
advertising type since we can not only rely on the HCI_CONNECTABLE flag
but must also check for a pending Set Connectable command (in which case
the flag does not yet have its final value).

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-14 11:23:28 -07:00
Johan Hedberg
c6d887aaf8 Bluetooth: Fix updating advertising data needlessly
We need to ensure that the advertising data is up-to-date whenever
advertising is enabled, but when disabling advertising we do not need to
worry about it (since it will eventually get fixed as soon as
advertising is enabled again). This patch fixes this in the command
complete callback for set_adv_enable.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-14 06:48:08 -07:00
Johan Hedberg
95c66e75ba Bluetooth: Move static advertising functions to avoid forward declarations
These functions will soon be used by set_connectable() so move them to a
location in mgmt.c that doesn't require forward declarations.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-14 06:48:08 -07:00
Johan Hedberg
37438c1f7f Bluetooth: Add missing error handling for Set Connectable
If the HCI commands related to the Set Connectable command fail we will
get a non-zero status in the request completion callback. In such a case
we must respond with the appropriate command status message to user space.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-14 06:48:08 -07:00
Johan Hedberg
d7b856f938 Bluetooth: Move more logic into set_connectable complete callback
This patch moves the responsibility of setting/clearing the
HCI_CONNECTABLE flag to the request completion callback of the Set
Connectable command. This will allow us to cleanly add support for LE
Advertising hooks in later patches.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-14 06:48:08 -07:00
Johan Hedberg
9b74246f3a Bluetooth: Reorganize set_connectable HCI command sending
This patch moves all the decisions of which HCI commands to send (or not
to send) to the code between hci_req_init() and hci_req_run() this
allows us to further extend the request with further commands but still
keep the same logic of handling whether to return a direct mgmt response
in the case that no HCI commands were sent.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-14 06:48:08 -07:00
Marcel Holtmann
d97c899bde Bluetooth: Introduce L2CAP channel callback for resuming
Clearing the BT_SK_SUSPEND socket flag from the L2CAP core is causing
a dependency on the socket. So intead of doing that, use a channel
callback into the socket handling to resume.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-14 14:23:24 +03:00
Marcel Holtmann
bdc2578307 Bluetooth: Introduce L2CAP channel flag for defer setup
The L2CAP core should not look into the socket flags to figure out the
setting of defer setup. So introduce a L2CAP channel flag that mirrors
the socket flag.

Since the defer setup option is only set in one place this becomes a
really easy thing to do.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-14 14:21:06 +03:00
Marcel Holtmann
c560575576 Bluetooth: Adjust header for proc socket information
The exposed socket information do not contain source or destination
addresses. So adjust the header accordingly.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-14 14:20:50 +03:00
Marcel Holtmann
dcbc729eef Bluetooth: Increase minor version of core module
There have been a lot of changes in the core Bluetooth handling
lately. So it is a good idea to increase the module version.

The module version is not used anywhere, but it makes debugging
a little bit simpler if versions can be distinguished.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 23:35:35 +03:00
Marcel Holtmann
2edf870d19 Bluetooth: Provide msg_name callback for L2CAP connectionless channels
The L2CAP connectionless channels use SOCK_DGRAM and recvmsg() and need
to receive the remote BD_ADDR and PSM information via msg_name from
the recvmsg() system call.

So in case the L2CAP socket is for connectionless channels, provide
a msg_name callback that can update the data. Also store the remote
BD_ADDR and PSM in the skb so it can be extracted later on.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 23:13:37 +03:00
Marcel Holtmann
d97636980f Bluetooth: Add support for per socket msg_name callback
This allows to add a per socket msg_name callback that can be used
for updating the msg_name information for recvmsg() system calls.

This feature is used by another patch to support address information
on L2CAP connectionless channels.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 23:10:33 +03:00
Marcel Holtmann
84b34d9867 Bluetooth: Use l2cap_pi(sk) directly where possible
There are few places where it makes sense to use l2cap_pi(sk) directly
instead of assigning it to temporary structure.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 21:40:12 +03:00
Marcel Holtmann
5f6cd79f47 Bluetooth: Remove src and dst fields from bt_sock structure
Every socket protocol now stores its own address information. So
just remove the generic src and dst fields since they are no longer
needed.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 21:11:25 +03:00
Marcel Holtmann
94a86df010 Bluetooth: Store RFCOMM address information in its own socket structure
The address information of RFCOMM sockets should be stored in its
own socket structure. Trying to generalize them is not helpful since
different transports have different address types.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 21:11:23 +03:00
Marcel Holtmann
eea963641b Bluetooth: Store SCO address information in its own socket structure
The address information of SCO sockets should be stored in its own
socket structure. Trying to generalize them is not helpful since
different transports have different address types.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 21:11:20 +03:00
Marcel Holtmann
041987cff6 Bluetooth: Use SCO addresses from HCI connection directly
Instead of storing a pointer to the addresses for the HCI device
and HCI connection, use them directly. With the recent changes
to address tracking of HCI connections, this becomes simple.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 21:11:18 +03:00
Marcel Holtmann
65f53e9802 Bluetooth: Access BNEP session addresses through L2CAP channel
The L2CAP socket structure does not contain the address information
anymore. They need to be accessed through the L2CAP channel.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 20:00:35 +03:00
Marcel Holtmann
755b82aa2f Bluetooth: Access HIDP session addresses through L2CAP channel
The L2CAP socket structure does not contain the address information
anymore. They need to be accessed through the L2CAP channel.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 20:00:33 +03:00
Marcel Holtmann
88f1fd2708 Bluetooth: Access CMTP session addresses through L2CAP channel
The L2CAP socket structure does not contain the address information
anymore. They need to be accessed through the L2CAP channel.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 20:00:30 +03:00
Marcel Holtmann
24bc10cad3 Bluetooth: Access RFCOMM session addresses through L2CAP channel
The L2CAP socket structure does not contain the address information
anymore. They need to be accessed through the L2CAP channel.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 20:00:28 +03:00
Marcel Holtmann
4f1654e084 Bluetooth: Return the correct address type for L2CAP sockets
The L2CAP sockets can use BR/EDR public, LE public and LE random
addresses for various combinations of source and destination
devices. So make sure that getsockname(), getpeername() and
accept() return the correct address type.

For this the address type of the source and destination is stored
with the L2CAP channel information. The stored address type is
not the one specific for the HCI protocol. It is the address
type used for the L2CAP sockets and the management interface.

The underlying HCI connections store the HCI address type. If
needed, it gets converted to the socket address type.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 18:58:30 +03:00
Marcel Holtmann
7eafc59e2f Bluetooth: Store address information in L2CAP channel structure
With the effort of abstracting the L2CAP socket from the underlying
L2CAP channel it is important to store the source and destination
address information directly in the L2CAP channel structure.

Direct access to the HCI connection address information is not
possible since they might not be avaiable at L2CAP channel
creation time. The address information will be updated when
the underlying BR/EDR or LE connection status changes.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 18:52:01 +03:00
Marcel Holtmann
4637f7c0d0 Bluetooth: Update L2CAP socket source address from HCI connection
When having LE connections, the source address is not always the
public address of the controller. So update the socket address
based on the actual used source address of the HCI connection.

This also remove the pointless source address pointer and adds
a proper lock around the socket structure.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 17:48:52 +03:00
Marcel Holtmann
f1560463eb Bluetooth: Fix coding style violations in SMP handling
The SMP source code has a few coding style violations. Fix them up
all at once. No actual code has changed.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 17:48:49 +03:00
Marcel Holtmann
c8462ca65f Bluetooth: Fix input address type for SMP C1 function
The smp_c1() so far always assumed public addresses as input for its
operation. However it should provide actually the source address type
of the actual connection.

Finally the source address type is tracked in hci_conn->src_type and
so use that one as input.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 17:48:47 +03:00
Marcel Holtmann
6f59b904ae Bluetooth: Use hci_conn->src address for L2CAP functions
The source address is now stored in hci_conn->src and so use that
one for L2CAP functions.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 17:48:45 +03:00
Marcel Holtmann
2b36a5620a Bluetooth: Use hci_conn->src address for SMP functions
The source address is now stored in hci_conn->src and so use that
one for SMP functions.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 17:48:42 +03:00
Marcel Holtmann
880be4e8d0 Bluetooth: Update source address and type for incoming LE connections
The incoming LE connections do not have a proper source address and
address type set. The connection needs to be set with the same values
as used for advertising parameters.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 17:48:29 +03:00
Marcel Holtmann
662e8820f3 Bluetooth: Store source address of HCI connections
The source addressed was based on the public address of the HCI device,
but with LE connections this not always the case. For example single
mode LE-only controllers would use a static random address. And this
address is configured by userspace.

To not complicate the lookup of what kind of address is in use, store
the correct source address for each HCI connection.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 17:47:37 +03:00
Marcel Holtmann
e7c4096e16 Bluetooth: Store the source address type of LE connections
When establishing LE connections, it is possible to use a public
address (if available) or a random address. The type of address
is only known when creating connections, so make sure it is
stored in hci_conn structure.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 17:46:31 +03:00
Marcel Holtmann
79d95a19a4 Bluetooth: Remove pointless bdaddr_to_le() helper function
The bdaddr_to_le() function tries to convert the internal address
type to one that matches the HCI address type for LE. It does not
handle any address types not used by LE and in the end just make
the code a lot harder to read.

So instead of just hiding behind a magic function, just convert
the internal address type where it needs to be converted. And it
turns out that these are only two cases anyway. One when creating
new LE connections and the other when loading the long term keys.
In both cases this makes it more clear on what it going on.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 17:45:55 +03:00
Marcel Holtmann
98e0f7ea4a Bluetooth: Remove l2cap_conn->src and l2cap_conn->dst usage from L2CAP
The l2cap_conn->src and l2cap_conn->dst addresses are just a pointers
to hci_conn structure. Use hci_conn->hdev->bdaddr and hci_conn->dst
directly instead.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 17:45:19 +03:00
Marcel Holtmann
ce39fb4e45 Bluetooth: Remove l2cap_conn->src and l2cap_conn->dst usage from SMP
The l2cap_conn->src and l2cap_conn->dst addresses are just a pointer
to hci_conn->hdev->bdaddr and hci_conn->dst structures. Use the data
provided by hci_conn directly. This is done for hci_conn->dst_type
already anyway and with this change it makes it a lot clearer were
the address information comes from.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 17:45:01 +03:00
Marcel Holtmann
bdc8ead27c Bluetooth: Remove l2cap_conn->dst usage from AMP manager
The l2cap_conn->dst address is just a pointer into the hci_conn->dst
structure. Use hci_conn->dst directly instead.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-13 17:43:32 +03:00
Marcel Holtmann
547d103280 Bluetooth: Unicast connectionless data reception is supported
The unicast connectionless data reception feature is actually support
and has been supported all along. Mark it as supported in the L2CAP
features bitmask.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-12 18:31:11 +03:00
Marcel Holtmann
d40bffbc4e Bluetooth: The L2CAP fixed channel connectionless data is supported
The implementation actually supports the L2CAP connectionless data
channel. So set it as supported in the fixed channels bitmask.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-12 18:30:29 +03:00
Marcel Holtmann
3124b84309 Bluetooth: Allow 3D profile to use security mode 4 level 0
The PSM 0x0021 is dedicated to the 3D profile and has permission to
use security mode 4 level 0 for L2CAP connectionless unicast data
transfers.

When establishing a L2CAP connectionless channel on PSM 0x0021, it
will no longer force Secure Simple Pairing.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-12 17:30:42 +03:00
Marcel Holtmann
6a974b50a1 Bluetooth: Limit security mode 4 level 0 to connection oriented channels
The exception for certain PSM channels when it comes to security
mode 4 level 0 should only be checked when actually a connection
oriented channel is established.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-12 17:29:39 +03:00
Marcel Holtmann
43b1b8dfb4 Bluetooth: Fix PSM value for L2CAP connectionless data packets
The put_unaligned() for setting the PSM is missing the (__le16 *)
cast. Without this, the PSM information transmitted over the air
are bogus.

In addition, print the used PSM value in the debug message so this
becomes easier to debug in the future.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-12 17:28:04 +03:00
Marcel Holtmann
4ca048e3a3 Bluetooth: Fix HCI init for 1st generation BlueFRITZ! devices
The 1st generation of BlueFRITZ! devices from AVM Berlin pretend
to be HCI version 1.2 controllers, but they are not. They are simple
Bluetooth 1.1 devices.

Since this company never created any newer controllers, it is safe
to use the manufacturer ID instead of an USB quirk.

< HCI Command: Read Page Scan Activity (0x03|0x001b) plen 0
> HCI Event: Command Complete (0x0e) plen 8
      Read Page Scan Activity (0x03|0x001b) ncmd 1
        Status: Success (0x00)
        Interval: 1280.000 msec (0x0800)
        Window: 21.250 msec (0x0022)
< HCI Command: Read Page Scan Type (0x03|0x0046) plen 0
> HCI Event: Command Status (0x0f) plen 4
      Read Page Scan Type (0x03|0x0046) ncmd 1
        Status: Unknown HCI Command (0x01)

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-12 09:46:35 +03:00
Marcel Holtmann
7f72134e08 Bluetooth: Add MGMT_OP_SET_SCAN_PARAMS to supported commands list
When adding support for MGMT_OP_SET_SCAN_PARAMS command the addition
to the supported commands list has been forgotten. This is needed
for userspace to detect if the command is supported or not.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-12 09:46:09 +03:00
Marcel Holtmann
a82974c9f4 Bluetooth: Don't advertise high speed support without SSP
It is not allowed to enable high speed support when Secure Simple
Pairing is not available or disabled.

However the support for high speed gets advertised on a controller
that does not even support Secure Simple Pairing. Since there is
no way to enable high speed support on such a controller, do not
even advertise its support.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11 19:48:13 +02:00
Marcel Holtmann
3a6afbd217 Bluetooth: Fix endless loop with HCI_QUIRK_RESET_ON_CLOSE
Really early versions of the Bluetooth specification were unclear
with the behavior of HCI Reset for USB devices. They assumed that
also an USB reset needs to be issued. Later Bluetooth specifications
cleared this out and it is safe to call HCI Reset without affecting
the transport.

For old devices that misbehave, the HCI_QUIRK_RESET_ON_CLOSE quirk
was introduced to postpone the HCI Reset until the device was no
longer in use.

One of these devices is the Digianswer BPA-105 Bluetooth Protocol
Analyzer. The only problem now is that with the quirk set, the
HCI Reset is also executed at the end of the setup phase. So the
controller gets configured and then it disconnects from the USB
bus, connects again, gets configured and of course disconnects
again. This game goes on forever.

For devices that need HCI_QUIRK_RESET_ON_CLOSE it is important
that the HCI Reset is not executed after the setup phase. In
specific when HCI_AUTO_OFF is set, do not call HCI Reset when
closing the device.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11 19:48:11 +02:00
Marcel Holtmann
14b49b9a49 Bluetooth: Add management command for setting LE scan parameters
The scan interval and window parameters are used for LE passive
background scanning and connection establishment. This allows
userspace to change the values.

These two values should be kept in sync with whatever is used for
the scan parameters service on remote devices. And it puts the
controlling daemon (for example bluetoothd) in charge of setting
the values.

Main use case would be to switch between two sets of values. One
for foreground applications and one for background applications.

At this moment, the values are only used for manual connection
establishment, but soon that should be extended to background
scanning and automatic connection establishment.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11 18:18:13 +02:00
Marcel Holtmann
bef64738e3 Bluetooth: Make LE scan interval and window a controller option
The scan interval and window for LE passive scanning and connection
establishment should be configurable on a per controller basis. So
introduce a setting that later on will allow modifying it.

This setting does not affect LE active scanning during device
discovery phase. As long as that phase uses interleaved discovery,
it will continuously scan.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11 18:18:11 +02:00
Marcel Holtmann
7bd8f09f69 Bluetooth: Add hdev parameter to hdev->send driver callback
Instead of masking hdev inside the skb->dev parameter, hand it
directly to the driver as a parameter to hdev->send. This makes
the driver interface more clear and simpler.

This patch fixes all drivers to accept and handle the new parameter
of hdev->send callback. Special care has been taken for bpa10x
and btusb drivers that require having skb->dev set to hdev for
the URB transmit complete handlers.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11 15:28:03 +02:00
Marcel Holtmann
e1a2617069 Bluetooth: Provide hdev parameter to hci_recv_frame() driver callback
To avoid casting skb->dev into hdev, just let the drivers provide
the hdev directly when calling hci_recv_frame() function.

This patch also fixes up all drivers to provide the hdev.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11 09:45:34 +02:00
Marcel Holtmann
5108699194 Bluetooth: Remove return value from hci_send_frame() function
The return value of hci_send_frame() is never checked. So just make
this function void and print an error when the hdev->send driver
callback returns a negative value.

Having the error printed is actually an improvement over the
current situation where any driver error just gets ignored.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11 00:19:44 +02:00
Marcel Holtmann
3d386acea0 Bluetooth: Remove pointless check of hci_send_frame parameter
The hdev parameter of hci_send_frame must be always valid. If the hdev
is not valid, it would not even make it to this stage. The callers
will have already accessed hdev at that point many times.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11 00:10:11 +02:00
Marcel Holtmann
57d17d70df Bluetooth: Move skb->dev assignment for hdev->send into central place
The assignement of skb->dev is done all over the place. So it makes it
hard to eventually get rid of it. Move it all in one central place so
it gets assigned right before calling hdev->send driver callback.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11 00:10:09 +02:00
Marcel Holtmann
ac4b723661 Bluetooth: Move smp.h header file into net/bluetooth/
The smp.h header file is only used internally by the bluetooth.ko
module and is not a public API. So make it local to the core
Bluetooth module.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11 00:10:07 +02:00
Marcel Holtmann
7024728ee5 Bluetooth: Move a2mp.h header file into net/bluetooth/
The a2mp.h header file is only used internally by the bluetooth.ko
module and is not a public API. So make it local to the core
Bluetooth module.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11 00:10:05 +02:00
Marcel Holtmann
7ef9fbf088 Bluetooth: Move amp.h header file into net/bluetooth/
The amp.h header file is only used internally by the bluetooth.ko
module and is not a public API. So make it local to the core
Bluetooth module.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11 00:10:03 +02:00
Marcel Holtmann
324d36ed26 Bluetooth: Remove hdev->ioctl driver callback
Since there is no use of hdev->ioctl by any Bluetooth driver since
ever, so just lets remove it.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10 22:11:41 +02:00
Marcel Holtmann
5b69bef541 Bluetooth: AMP contollers do not support the legacy ioctls
The legacy ioctls for device specific commands including inquiry are
not support by AMP controllers. So just reject them right away instead
of trying to send the HCI command and wait for failure from the
actual hardware.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10 22:08:37 +02:00
Marcel Holtmann
b145edcd16 Bluetooth: Use hci_conn_num() for checking number of LE connections
When checking for the current number of LE connections, use
hci_conn_num() function instead of a full blown lookup within
the connection hash or direct access of the counters.

In the case of re-enabling advertising, it is more useful to
check for any connection attempt or existing connection.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10 22:07:20 +02:00
Marcel Holtmann
21b5187f23 Bluetooth: Fix too long line with set_advertising() function
The function declaration goes over 80 characters, so break it down.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10 22:07:00 +02:00
Johan Hedberg
cebf4cfd86 Bluetooth: Fix checking for HCI_SETUP flag when receiving mgmt commands
When the HCI_SETUP flag is set the controller has not yet been announced
over mgmt and therefore doesn't exist from that perspective. If we
nevertheless get a mgmt command for it we should respond with the
appropriate INVALID_INDEX error.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-10 09:13:45 -07:00
Johan Hedberg
c4e5bafa66 Bluetooth: Fix potential double-frees of L2CAP skbs
The l2cap_recv_frame function is expected to take ownership and
eventually free the skb passed to it. We need to ensure that the
conn->rx_skb pointer is no longer reachable when calling
l2cap_recv_frame so that no other function, such as l2cap_conn_del, may
think that it can free conn->rx_skb.

An actual situation when this can happen is when smp_sig_channel (called
from l2cap_recv_frame) fails and l2cap_conn_del gets called as a
consequence. The l2cap_conn_del function would then try to free
conn->rx_skb, but as the same skb was just passed to smp_sig_channel and
freed we get a double-free.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-10 05:00:34 -07:00
Marcel Holtmann
9ecb3e2425 Bluetooth: Restrict high speed support to SSP enabled controllers
The support for Bluetooth High Speed can only be enabled on controllers
where also Secure Simple Pairing has been enabled. Trying to enable
high speed when SSP is disabled will result into an error. Disabling
SSP will at the same time disable high speed as well.

It is required to enforce this dependency on SSP since high speed
support is only defined for authenticated, unauthenticated and
debug link keys. These link key types require SSP.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10 12:54:51 +02:00
Marcel Holtmann
72ef0c1a9e Bluetooth: Remove unneeded val variable when setting SSP
The variable val in the set_ssp() function of the management interface
is not needed. Just use cp->val directly since its input values have
already been validated.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10 12:54:51 +02:00
Andre Guedes
620ad5219c Bluetooth: Refactor hci_connect_le
This patch does some code refactoring in hci_connect_le() by moving
the exception code into if statements and letting the main flow in
first level of function scope. It also adds extra comments to improve
the code readability.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-10 01:30:18 -07:00
Andre Guedes
1d399ae5c7 Bluetooth: Use HCI request for LE connection
This patch introduces a new helper, which uses the HCI request
framework, for creating LE connectons. All the handling is now
done by this function so we can remove the hci_cs_le_create_conn()
event handler.

This patch also removes the old hci_le_create_connection() since
it is not used anymore.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-10 01:30:18 -07:00
Johan Hedberg
f74ca9b809 Bluetooth: Fix changing advertising setting while LE is connected
We only (re)enable advertising when LE is disconnected. Trying to enable
advertising using mgmt_set_advertising while connected should simply
change the flag but not do anything else (until the connection gets
dropped). This patch fixes this by making an LE connection lookup to
determine whether there are any connected devices or not.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-08 07:49:02 -07:00
Johannes Berg
c1f23a2bfc Bluetooth: Fix variable shadow warnings
Sparse points out three places where variables are shadowed,
rename two of the variables and remove the duplicate third.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-07 09:52:12 -07:00
Marcel Holtmann
f38ba94147 Bluetooth: Read flow control mode on AMP controller init
When initializing an AMP controller, read its current flow control
mode so that the correct value is used.

The AMP controller defaults to block based flow control and this
extra command is just to double check.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-07 16:53:43 +02:00
Marcel Holtmann
7528ca1c5a Bluetooth: Read location data on AMP controller init
When initializing an AMP controller, read its current known location
data so that it can be analyzed later on.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-07 16:53:40 +02:00
Marcel Holtmann
f6996cfe2f Bluetooth: Read supported features and commands on AMP controllers
The commands for reading supported features and commands are both
supported by AMP controllers. Issue them during controller init
phase so their values are known.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-07 14:51:54 +02:00
Marcel Holtmann
cd0a85c22c Bluetooth: List powered down AMP controllers correctly
Within the AMP discover response, list powered down AMP controllers
as powered down. No point in trying to make them look any different.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-07 10:08:42 +02:00
Marcel Holtmann
93c311a044 Bluetooth: Make mgmt power down notification for BR/EDR explicit
The management interface only operates on BR/EDR controllers. The check
for the power down notification is a bit intermixed with the check if
controller auto power off is active. Since there are more than just
BR/EDR controllers supported, make this check explicit since the auto
power off check also applies to AMP controllers and it has to happen
in this exact order. Otherwise the bit will not be cleared.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-07 10:08:39 +02:00
Marcel Holtmann
004b02589c Bluetooth: Power off AMP controllers after setup phase
Even AMP controllers should be powered off after the setup phase. It
is not a good idea to keep AMP controllers powered on all the time
if they are not in use.

Power on of the AMP controller can either be done manually via
command line commands or directly via A2MP. Especially since there
is an indication in A2MP for powered down controllers that can
be activated.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-07 10:08:36 +02:00
Marcel Holtmann
2f1e063bc0 Bluetooth: Make mgmt_discovering() return void
The return value of mgmt_discovering() function is not used
and so just change it to return void.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-07 09:19:28 +02:00
Marcel Holtmann
9cf12aee8b Bluetooth: Make mgmt_remote_name() return void
The return value of mgmt_remote_name() function is not used
and so just change it to return void.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-07 09:19:25 +02:00
Marcel Holtmann
901801b9a4 Bluetooth: Make mgmt_device_found() return void
The return value of mgmt_device_found() function is not used
and so just change it to return void.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-07 09:19:23 +02:00
Marcel Holtmann
9b80ec5e8e Bluetooth: Make mgmt_device_disconnected() return void
The return value of mgmt_device_disconnected() function is not used
and so just change it to return void.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-07 09:19:21 +02:00
Marcel Holtmann
ecd90ae7f6 Bluetooth: Make mgmt_device_connected() return void
The return value of mgmt_device_connected() function is not used
and so just change it to return void.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-07 09:19:19 +02:00
Marcel Holtmann
445608d078 Bluetooth: Make mgmt_connect_failed() return void
The return value of mgmt_connect_failed() function is not used
so change it to just return void.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-07 09:19:18 +02:00
Marcel Holtmann
7892924c7d Bluetooth: Make mgmt_disconnect_failed() return void
The return value of mgmt_disconnect_failed() function is not used
so change it to just return void.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-07 09:19:16 +02:00
Marcel Holtmann
3eec705e42 Bluetooth: Make mgmt_set_powered_failed() return void
The return value of mgmt_set_powered_failed() function is never used
and so make the function just return void.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-07 09:19:13 +02:00
Marcel Holtmann
bf6b56db0a Bluetooth: Make mgmt_index_added() and mgmt_index_removed() return void
The return value from mgmt_index_added() and mgmt_index_removed()
functions is never used. So do not pretend that returning an error
would actually be handled and just make both functions return void.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-07 09:19:12 +02:00
Marcel Holtmann
5559435654 Bluetooth: Send new settings only when pairable changes
In case the current value of pairable is already configured, do not
send a new settings event indicating that something has changed while
in reality everything is the same.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-07 08:52:26 +02:00
Marcel Holtmann
1514b8928e Bluetooth: Remove mgmt_valid_hdev() helper function
The helper function mgmt_valid_hdev() is more obfuscating the code
then it makes it easier to read. So intead of this helper, use the
direct check for BR/EDR device type.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 17:58:45 +02:00
Marcel Holtmann
a6d811ed28 Bluetooth: Remove no longer needed mgmt_new_settings() function
The mgmt_new_settings() function was only needed to handle the
error case when re-enabling advertising failed. Since that is
now handled internally inside the management core, this function
is not needed anymore. So just remove it.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 15:01:21 +02:00
Marcel Holtmann
5976e60811 Bluetooth: Use helper function for re-enabling advertising
When the all LE connections have been disconneted, then it is up to
the host to re-enable advertising at that point. To ensure that the
correct advertising parameters are used, force the usage of the
common helper to enable advertising.

The change just moves the manual enabling of advertising from the
event handler into the management core so that the helper can
be actually shared.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 15:00:07 +02:00
Marcel Holtmann
b4faf30096 Bluetooth: Set LE advertising parameters before enabling it
The LE advertising parameters can only be modified when advertising
is disabled. So before enabling it, make sure the controller has all
the right parameters.

Right now all default values are used and thus this does no change
any existing behavior. One minor exception is that in case of single
mode LE-only controllers without a public address, now the random
address is used for advertising.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 14:59:25 +02:00
Marcel Holtmann
bba3aa550f Bluetooth: Use helper functions for enabling/disabling advertising
The tasks of enabling and disabling advertising are required in many
cases. So refactor the actual HCI operations into two common helpers
to make the code simpler.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 14:53:25 +02:00
Marcel Holtmann
03d87419de Bluetooth: Make it clear that disabling LE disables advertising
This is not a functional change, just change the code to make it easy
to understand that advertising gets disabled before LE support will
be turned off.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 14:53:08 +02:00
Marcel Holtmann
c25dfc610b Bluetooth: Use random address if public address is not available
For single mode LE-only controllers, it is possible that they come
without a public address. If a public address is not available,
then use the random address for connection establishment and
scanning.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 11:13:11 +02:00
Marcel Holtmann
e8803534a0 Bluetooth: Simplify device type check for AMP discover response
When counting the number for AMP controllers, a positive check is
used. To be consistent, use the same check when actually adding
the data for the AMP contollers.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 11:12:47 +02:00
Marcel Holtmann
01cd340427 Bluetooth: Use explicit check for BR/EDR device type
The BR/EDR and LE setup procedures apply only to BR/EDR device types
and so check for that explicitly. Checking that it is not an AMP
controller is dangerous in case there will be ever a third device
type.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 11:00:40 +02:00
Marcel Holtmann
a5c8f270e4 Bluetooth: Reject enabling controllers without valid addresses
In case of a single mode LE-only controller it is possible that no
public address is used. These type of controllers require a random
address to be configured.

Without a configured static random address, such a controller is
not functional. So reject powering on the controller in this case
until it gets configured with a random address.

The controller setup stage is still run since it is the only way
to determinate if a public address is available or not. So it is
similar on how RFKILL gets handled during initial setup of the
controller.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 10:50:50 +02:00
Marcel Holtmann
a646bd8194 Bluetooth: Check for non BR/EDR controller in AMP discover response
Within the AMP discover response, all controllers that are not the
primary BR/EDR controller are valid.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 10:42:54 +02:00
Marcel Holtmann
1df7b17a87 Bluetooth: Simplify check if L2CAP connection is AMP capable
The check if a L2CAP connection is AMP capable was a little bit
complicated. This changes the code to make it simpler and more
readable.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 10:26:31 +02:00
Marcel Holtmann
80d58d0b5b Bluetooth: Move hci_amp_capable() function into L2CAP core
The hci_amp_capable() function has only a single user inside the L2CAP
core. Instead of exporting the function, place it next to its user.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 10:25:58 +02:00
Marcel Holtmann
23f0cb41a2 Bluetooth: Remove check for number of AMP controller
The number of controllers for the AMP discover response has already
been calculated. And since the hci_dev_list lock is held, it can not
change. So there is no need for any extra checks.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 10:25:30 +02:00
Marcel Holtmann
346e7099c2 Bluetooth: Remove pointless inline function
The inline function for BR/EDR controller AMP discover response
info is rather useless. Just include the code into the function
that builds the whole response.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 10:25:07 +02:00
Marcel Holtmann
536619e86d Bluetooth: Rename AMP status constants and use them
The AMP controller status constants need to be actually used to avoid
crypted hardcoded numbers.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 10:24:30 +02:00
Marcel Holtmann
6ed971ca4f Bluetooth: Use explicit AMP controller id value for BR/EDR
The special AMP controller id 0 is reserved for the BR/EDR controller
that has the main link. It is a fixed value and so use a constant for
this throughout the code to make it more visible when the handling is
for the BR/EDR channel or when it is for the AMP channel.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 10:23:39 +02:00
Marcel Holtmann
ece6912648 Bluetooth: Separate AMP controller type from HCI device type
There are two defined HCI device types. One is for BR/EDR controllers
and the other is for AMP controllers. The HCI device type is not the
same as the AMP controller type. It just happens that currently the
defined types match, but that is not guaranteed.

Split the usage of AMP controller type into its own domain so that
it is possible to separate between BR/EDR controllers, 802.11 AMP
controllers and any other AMP technology that might be defined in
the future.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 10:22:38 +02:00
Marcel Holtmann
f822c411b2 Bluetooth: Remove useless external function to count controllers
The list of controllers can be counted ahead of time and inline
inside the AMP discover handling. There is no need to export such
a function at all.

In addition just count the AMP controller and only allocated space
for a single mandatory BR/EDR controller. No need to allocate more
space than needed.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 10:21:09 +02:00
Marcel Holtmann
23b9003b9a Bluetooth: Fix controller list for AMP discover response
The AMP discover response should list exactly one BR/EDR controller
and ignore all other BR/EDR controller.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-06 10:19:53 +02:00
Johan Hedberg
2210246cf5 Bluetooth: Fix re-enabling advertising after a connection
LE controllers will automatically disable advertising whenever they
accept a new connection. In order not to fall out of sync with the
advertising setting we need to re-enable advertising whenever the last
LE connection drops. A failure to re-enable advertising should cause the
setting to be disabled, so this patch also calls mgmt_new_settings()
when this happens.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-05 03:03:38 -07:00
Johan Hedberg
d2f5a196d7 Bluetooth: Add public mgmt function to send New Settings event
A function is needed so that the HCI event processing can ask the mgmt
code to emit a new settings event. This is necessary e.g. when the event
processing does updates to mgmt related states without any dependency of
actual mgmt commands.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-05 03:03:38 -07:00
Johan Hedberg
f3d3444a4d Bluetooth: Rename HCI_LE_PERIPHERAL to HCI_ADVERTISING
This flag is used to indicate whether we want to have advertising
enabled or not, so give it a more suitable name.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-05 03:03:38 -07:00
Andre Guedes
46a190cbd3 Bluetooth: Initialize hci_conn fields in hci_connect_le
This patch moves some hci_conn fields initialization from hci_le_
create_connection() to hci_connect_le(). It makes more sense to
initialize these fields within the function that creates the hci_
conn object.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-03 23:07:17 -07:00
Andre Guedes
f1e5d54743 Bluetooth: Rename hci_conn variable in hci_connect_le()
This patch simply rename the hci_conn variable "le" to "conn"
since it is a better name.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-03 23:07:17 -07:00
Marcel Holtmann
4f3e219d95 Bluetooth: Only one command per L2CAP LE signalling is supported
The Bluetooth specification makes it clear that only one command
should be present in the L2CAP LE signalling packet. So tighten
the checks here and restrict it to exactly one command.

This is different from L2CAP BR/EDR signalling where multiple
commands can be part of the same packet.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-03 16:09:59 +03:00
Marcel Holtmann
92381f5cd7 Bluetooth: Check minimum length of SMP packets
When SMP packets are received, make sure they contain at least 1 byte
header for the opcode. If not, drop the packet and disconnect the link.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-03 13:06:41 +03:00
Marcel Holtmann
b99707d7ee Bluetooth: Drop packets on ATT fixed channel on BR/EDR
The ATT fixed channel is only valid when using LE connections. On
BR/EDR it is required to go through L2CAP connection oriented
channel for ATT.

Drop ATT packets when they are received on a BR/EDR connection.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-03 13:05:36 +03:00
Marcel Holtmann
ae4fd2d374 Bluetooth: L2CAP connectionless channels are only valid for BR/EDR
When receiving connectionless packets on a LE connection, just drop
the packet. There is no concept of connectionless channels for LE.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-03 10:13:30 +03:00
Marcel Holtmann
7b9899dbcf Bluetooth: SMP packets are only valid on LE connections
When receiving SMP packets on a BR/EDR connection, then just drop
the packet and do not try to process it.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-03 10:09:12 +03:00
Marcel Holtmann
94b6a09b67 Bluetooth: Don't copy L2CAP LE signalling to raw sockets
The L2CAP raw sockets are only used for BR/EDR signalling. Packets
on LE links should not be forwarded there.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-03 10:07:58 +03:00
Marcel Holtmann
a28776296c Bluetooth: Fix switch statement order for L2CAP fixed channels
The switch statement for the various L2CAP fixed channel handlers
is not really ordered.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-03 10:07:29 +03:00
Marcel Holtmann
6203fc9834 Bluetooth: Allow changing device class when BR/EDR is disabled
Changing the device class when BR/EDR is disabled has no visible
effect for remote devices. However to simplify the logic allow it
as long as the controller supports BR/EDR operations.

If it is not allowed, then the overall logic becomes rather
complicated since the class of device values would need clearing
or restoring when BR/EDR setting changes.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-03 10:05:27 +03:00
Marcel Holtmann
cf99ba1359 Bluetooth: Restrict loading of long term keys to LE capable controllers
Loading long term keys into a BR/EDR only controller make no sense.
The kernel would never use any of these keys. So instead of allowing
userspace to waste memory, reject such operation with a not supported
error message.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-03 09:33:02 +03:00
Marcel Holtmann
9060d5cf52 Bluetooth: Restrict loading of link keys to BR/EDR capable controllers
Loading link keys into a LE only controller make no sense. The kernel
would never use any of these keys. So instead of allowing userspace
to waste memory, reject such operation with a not supported error
message.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-03 09:32:57 +03:00
Marcel Holtmann
62af444319 Bluetooth: Allow setting static address even if LE is disabled
Setting the static address does not depend on LE beeing enabled. It
only depends on a controller with LE support.

When depending on LE enabled this command becomes really complicated
since in case LE gets disabled, it would be required to clear the
static address and also its random address representation inside
the controller. With future support for private addresses such
complex setup should be avoided.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-03 09:29:38 +03:00
Marcel Holtmann
cdba5281b2 Bluetooth: Restrict SSP setting changes to BR/EDR enabled controllers
Only when BR/EDR is supported and enabled, allow changing of the SSP
setting. Just checking if the hardware supports SSP is not enough
since it might be the case that BR/EDR is disabled.

In the case that BR/EDR is disabled, but SSP supported by the
controller the not supported error message is now returned.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-03 09:20:37 +03:00
Marcel Holtmann
3b1662952e Bluetooth: Fix memory leak with L2CAP signal channels
The wrong type of L2CAP signalling packets on the wrong type of
either BR/EDR or LE links need to be dropped. When that happens
the packet is dropped, but the memory not freed. So actually
free the memory as well.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-10-02 17:17:05 -03:00
Marcel Holtmann
9ab8cf3729 Bluetooth: Increment management interface revision
This patch increments the management interface revision due to the
various fixes, improvements and other changes that have gone in
lately.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-02 16:24:03 +03:00
Johan Hedberg
11802b299f Bluetooth: Fix advertising data flags with disabled BR/EDR
We shouldn't include the simultaneous LE & BR/EDR flags in the LE
advertising data if BR/EDR is disabled on a dual-mode controller. This
patch fixes this issue and ensures that the create_ad function generates
the correct flags when BR/EDR is disabled.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-02 06:18:18 -07:00
Johan Hedberg
e6fe798652 Bluetooth: Fix REJECTED vs NOT_SUPPORTED mgmt responses
The REJECTED management response should mainly be used when the adapter
is in a state where we cannot accept some command or a specific
parameter value. The NOT_SUPPORTED response in turn means that the
adapter really cannot support the command or parameter value.

This patch fixes this distinction and adds two helper functions to
easily get the appropriate LE or BR/EDR related status response.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-02 05:52:51 -07:00
Marcel Holtmann
d13eafce2c Bluetooth: Add management command for setting static address
On dual-mode BR/EDR/LE and LE only controllers it is possible
to configure a random address. There are two types or random
addresses, one is static and the other private. Since the
random private addresses require special privacy feature to
be supported, the configuration of these two are kept separate.

This command allows for setting the static random address. It is
only supported on controllers with LE support. The static random
address is suppose to be valid for the lifetime of the controller
or at least until the next power cycle. To ensure such behavior,
setting of the address is limited to when the controller is
powered off.

The special BDADDR_ANY address (00:00:00:00:00:00) can be used to
disable the static address. This is also the default value.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-02 14:50:58 +03:00
Marcel Holtmann
a0cdf960be Bluetooth: Restrict disabling of HS when controller is powered off
Disabling the high speed setting when the controller is powered on has
too many side effects that are not taken care of. And in general it
is not an useful operation anyway. So just make such a command fail
with a rejection error message.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-02 13:51:50 +03:00
Johan Hedberg
0663ca2a03 Bluetooth: Add a new mgmt_set_bredr command
This patch introduces a new mgmt command for enabling/disabling BR/EDR
functionality. This can be convenient when one wants to make a dual-mode
controller behave like a single-mode one. The command is only available
for dual-mode controllers and requires that LE is enabled before using
it. The BR/EDR setting can be enabled at any point, however disabling it
requires the controller to be powered off (otherwise a "rejected"
response will be sent).

Disabling the BR/EDR setting will automatically disable all other BR/EDR
related settings.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-02 03:48:28 -07:00
Johan Hedberg
56f8790102 Bluetooth: Introduce a new HCI_BREDR_ENABLED flag
To allow treating dual-mode (BR/EDR/LE) controllers as single-mode ones
(LE-only) we want to introduce a new HCI_BREDR_ENABLED flag to track
whether BR/EDR is enabled or not (previously we simply looked at the
feature bit with lmp_bredr_enabled).

This patch add the new flag and updates the relevant places to test
against it instead of using lmp_bredr_enabled. The flag is by default
enabled when registering an adapter and only cleared if necessary once
the local features have been read during the HCI init procedure.

We cannot completely block BR/EDR usage in case user space uses raw HCI
sockets but the patch tries to block this in places where possible, such
as the various BR/EDR specific ioctls.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-02 03:48:28 -07:00
Johan Hedberg
e1d08f4067 Bluetooth: Fix workqueue synchronization in hci_dev_open
When hci_sock.c calls hci_dev_open it needs to ensure that there isn't
pending work in progress, such as that which is scheduled for the
initial setup procedure or the one for automatically powering off after
the setup procedure. This adds the necessary calls to ensure that any
previously scheduled work is completed before attempting to call
hci_dev_do_open.

This patch fixes a race with old user space versions where we might
receive a HCIDEVUP ioctl before the setup procedure has been completed.
When that happens the setup procedures callback may fail early and leave
the device in an inconsistent state, causing e.g. the setup callback to
be (incorrectly) called more than once.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-01 23:27:08 -07:00
Johan Hedberg
cbed0ca137 Bluetooth: Refactor hci_dev_open to a separate hci_dev_do_open function
The requirements of an external call to hci_dev_open from hci_sock.c are
different to that from within hci_core.c. In the former case we want to
flush any pending work in hdev->req_workqueue whereas in the latter we
don't (since there we are already calling from within the workqueue
itself). This patch does the necessary refactoring to a separate
hci_dev_do_open function (analogous to hci_dev_do_close) but does not
yet introduce the synchronizations relating to the workqueue usage.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-01 23:27:08 -07:00
Marcel Holtmann
922ca1dfc2 Bluetooth: Enable -D__CHECK_ENDIAN__ for sparse by default
The Bluetooth protocol and hardware is pretty much all little endian
and so when running sparse via "make C=2" for example, enable the
endian checks by default.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-02 09:10:05 +03:00
Marcel Holtmann
10a8b86f57 Bluetooth: Require CAP_NET_ADMIN for HCI User Channel operation
The HCI User Channel operation is an admin operation that puts the
device into promiscuous mode for single use. It is more suitable
to require CAP_NET_ADMIN than CAP_NET_RAW.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-02 09:10:04 +03:00
Marcel Holtmann
ee39269369 Bluetooth: Send new settings event when changing high speed option
When enabling or disabling high speed setting it is required to send
a new settings event to inform other management interface users about
the changed settings.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-02 09:10:01 +03:00
Marcel Holtmann
848566b381 Bluetooth: Provide high speed configuration option
Hiding the Bluetooth high speed support behind a module parameter is
not really useful. This can be enabled and disabled at runtime via
the management interface. This also has the advantage that this can
now be changed per controller and not just global.

This patch removes the module parameter and exposes the high speed
setting of the management interface to all controllers.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-02 09:09:59 +03:00
Marcel Holtmann
60f2a3ed7b Bluetooth: Use only 2 bits for controller type information
The controller type is limited to BR/EDR/LE and AMP controllers. This
can be easily encoded with just 2 bits and still leave enough room
for future controller types.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-02 09:09:54 +03:00
Gustavo Padovan
1025c04cec Merge git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Conflicts:
	net/bluetooth/hci_core.c
2013-09-27 11:56:14 -03:00
Johan Hedberg
4375f1037d Bluetooth: Add new mgmt_set_advertising command
This patch adds a new mgmt command for enabling and disabling
LE advertising. The command depends on the LE setting being enabled
first and will return a "rejected" response otherwise. The patch also
adds safeguards so that there will ever only be one set_le or
set_advertising command pending per adapter.

The response handling and new_settings event sending is done in an
asynchronous request callback, meaning raw HCI access from user space to
enable advertising (e.g. hciconfig leadv) will not trigger the
new_settings event. This is intentional since trying to support mixed
raw HCI and mgmt access would mean adding extra state tracking or new
helper functions, essentially negating the benefit of using the
asynchronous request framework. The HCI_LE_ENABLED and HCI_LE_PERIPHERAL
flags however are updated correctly even with raw HCI access so this
will not completely break subsequent access over mgmt.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-09-25 14:30:11 -03:00
Johan Hedberg
eeca6f8913 Bluetooth: Add new mgmt setting for LE advertising
This patch adds a new mgmt setting for LE advertising and hooks up the
necessary places in the mgmt code to operate on the HCI_LE_PERIPHERAL
flag (which corresponds to this setting). This patch does not yet add
any new command for enabling the setting - that is left for a subsequent
patch.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-09-25 14:30:11 -03:00
Johan Hedberg
416a4ae56b Bluetooth: Use async request for LE enable/disable
This patch updates the code to use an asynchronous request for handling
the enabling and disabling of LE support. This refactoring is necessary
as a preparation for adding advertising support, since when LE is
disabled we should also disable advertising, and the cleanest way to do
this is to perform the two respective HCI commands in the same
asynchronous request.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-09-25 14:30:11 -03:00
Johan Hedberg
bd99abdd5b Bluetooth: Move mgmt response convenience functions to a better location
The settings_rsp and cmd_status_rsp functions can be useful for all mgmt
command handlers when asynchronous request callbacks are used. They will
e.g. be used by subsequent patches to change set_le to use an async
request as well as a new set_advertising command. Therefore, move them
higher up in the mgmt.c file to avoid unnecessary forward declarations
or mixing this trivial change with other patches.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-09-25 14:30:10 -03:00
Johan Hedberg
87b95ba64e Bluetooth: Fix busy return for mgmt_set_powered in some cases
We should return a "busy" error always when there is another
mgmt_set_powered operation in progress. Previously when powering on
while the auto off timer was still set the code could have let two or
more pending power on commands to be queued. This patch fixes the issue
by moving the check for duplicate commands to an earlier point in the
set_powered handler.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-09-25 14:30:10 -03:00
Johan Hedberg
970871bc9c Bluetooth: Clean up socket locking in l2cap_sock_recvmsg
This patch cleans up the locking login in l2cap_sock_recvmsg by pairing
up each lock_sock call with a release_sock call. The function already
has a "done" label that handles releasing the socket and returning from
the function so the fix is rather simple.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-09-25 14:30:10 -03:00
Johan Hedberg
0fba96f97b Bluetooth: Add clarifying comment to bt_sock_wait_state()
The bt_sock_wait_state requires the sk lock to be held (through
lock_sock) so document it clearly in the code.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-09-25 14:30:10 -03:00
Peter Senna Tschudin
941247f910 Bluetooth: Fix assignment of 0/1 to bool variables
Convert 0 to false and 1 to true when assigning values to bool
variables. Inspired by commit 3db1cd5c05.

The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):

@@
bool b;
@@
(
-b = 0
+b = false
|
-b = 1
+b = true
)

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-09-22 16:59:14 -05:00