Commit 7627a0edef ("ata: ahci: Drop low power policy board type")
dropped the board_ahci_low_power board type, and instead enables LPM if:
-The AHCI controller reports that it supports LPM (Partial/Slumber), and
-CONFIG_SATA_MOBILE_LPM_POLICY != 0, and
-The port is not defined as external in the per port PxCMD register, and
-The port is not defined as hotplug capable in the per port PxCMD
register.
Partial and Slumber LPM states can either be initiated by HIPM or DIPM.
For HIPM (host initiated power management) to get enabled, both the AHCI
controller and the drive have to report that they support HIPM.
For DIPM (device initiated power management) to get enabled, only the
drive has to report that it supports DIPM. However, the HBA will reject
device requests to enter LPM states which the HBA does not support.
The problem is that Apacer AS340 drives do not handle low power modes
correctly. The problem was most likely not seen before because no one
had used this drive with a AHCI controller with LPM enabled.
Add a quirk so that we do not enable LPM for this drive, since we see
command timeouts if we do (even though the drive claims to support DIPM).
Fixes: 7627a0edef ("ata: ahci: Drop low power policy board type")
Cc: stable@vger.kernel.org
Reported-by: Tim Teichmann <teichmanntim@outlook.de>
Closes: https://lore.kernel.org/linux-ide/87bk4pbve8.ffs@tglx/
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Commit 7627a0edef ("ata: ahci: Drop low power policy board type")
dropped the board_ahci_low_power board type, and instead enables LPM if:
-The AHCI controller reports that it supports LPM (Partial/Slumber), and
-CONFIG_SATA_MOBILE_LPM_POLICY != 0, and
-The port is not defined as external in the per port PxCMD register, and
-The port is not defined as hotplug capable in the per port PxCMD
register.
Partial and Slumber LPM states can either be initiated by HIPM or DIPM.
For HIPM (host initiated power management) to get enabled, both the AHCI
controller and the drive have to report that they support HIPM.
For DIPM (device initiated power management) to get enabled, only the
drive has to report that it supports DIPM. However, the HBA will reject
device requests to enter LPM states which the HBA does not support.
The problem is that AMD Radeon S3 SSD drives do not handle low power modes
correctly. The problem was most likely not seen before because no one
had used this drive with a AHCI controller with LPM enabled.
Add a quirk so that we do not enable LPM for this drive, since we see
command timeouts if we do (even though the drive claims to support both
HIPM and DIPM).
Fixes: 7627a0edef ("ata: ahci: Drop low power policy board type")
Cc: stable@vger.kernel.org
Reported-by: Doru Iorgulescu <doru.iorgulescu1@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218832
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Commit 7627a0edef ("ata: ahci: Drop low power policy board type")
dropped the board_ahci_low_power board type, and instead enables LPM if:
-The AHCI controller reports that it supports LPM (Partial/Slumber), and
-CONFIG_SATA_MOBILE_LPM_POLICY != 0, and
-The port is not defined as external in the per port PxCMD register, and
-The port is not defined as hotplug capable in the per port PxCMD
register.
Partial and Slumber LPM states can either be initiated by HIPM or DIPM.
For HIPM (host initiated power management) to get enabled, both the AHCI
controller and the drive have to report that they support HIPM.
For DIPM (device initiated power management) to get enabled, only the
drive has to report that it supports DIPM. However, the HBA will reject
device requests to enter LPM states which the HBA does not support.
The problem is that Crucial CT240BX500SSD1 drives do not handle low power
modes correctly. The problem was most likely not seen before because no
one had used this drive with a AHCI controller with LPM enabled.
Add a quirk so that we do not enable LPM for this drive, since we see
command timeouts if we do (even though the drive claims to support DIPM).
Fixes: 7627a0edef ("ata: ahci: Drop low power policy board type")
Cc: stable@vger.kernel.org
Reported-by: Aarrayy <lp610mh@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218832
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Commit:
7bc263840b ("sched/topology: Consolidate and clean up access to a CPU's max compute capacity")
removed rq->cpu_capacity_orig in favor of using arch_scale_freq_capacity()
calls. Export the underlying percpu symbol on x86 so that external trace
point helper modules can be made to work again.
Signed-off-by: Phil Auld <pauld@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20240530181548.2039216-1-pauld@redhat.com
Fix the warning from 'make C=1 W=1':
WARNING: modpost: missing MODULE_DESCRIPTION() in arch/x86/events/rapl.o
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Link: https://lore.kernel.org/r/20240530-md-arch-x86-events-v1-1-e45ffa8af99f@quicinc.com
At converting between the legacy event and UMP, the parameters for
MIDI Song Position Pointer are incorrectly stored. It should have
been LSB -> MSB order while it stored in MSB -> LSB order.
This patch corrects the ordering.
Fixes: e9e02819a9 ("ALSA: seq: Automatic conversion of UMP events")
Link: https://lore.kernel.org/r/20240531075110.3250-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit bf20ab538c ("blk-throttle: remove CONFIG_BLK_DEV_THROTTLING_LOW")
attempts to revert the code change introduced by commit cd5ab1b0fc
("blk-throttle: add .low interface"). However, it leaves behind the
bps_conf[] and iops_conf[] fields in the throtl_grp structure which
aren't set anywhere in the new blk-throttle.c code but are still being
used by tg_prfill_limit() to display the limits in io.max. Now io.max
always displays the following values if a block queue is used:
<m>:<n> rbps=0 wbps=0 riops=0 wiops=0
Fix this problem by removing bps_conf[] and iops_conf[] and use bps[]
and iops[] instead to complete the revert.
Fixes: bf20ab538c ("blk-throttle: remove CONFIG_BLK_DEV_THROTTLING_LOW")
Reported-by: Justin Forbes <jforbes@redhat.com>
Closes: https://github.com/containers/podman/issues/22701#issuecomment-2120627789
Signed-off-by: Waiman Long <longman@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20240530134547.970075-1-longman@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
- One pcode polling timeout change
- One fix for deadlocks for faulting VMs
- One error-path lock imbalance fix
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRskUM7w1oG5rx2IZO4FpNVCsYGvwUCZlirfAAKCRC4FpNVCsYG
vwalAQD6DkKE47jSCctG0JwKFL3BARZAxmTnTPhsoPcmQTKtMAD+KME0KZmPaY0v
SrT2YKXpPp4tkmmtSyQcHeolk65KLgw=
=+tyt
-----END PGP SIGNATURE-----
Merge tag 'drm-xe-fixes-2024-05-30' of https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes
Driver Changes:
- One pcode polling timeout change
- One fix for deadlocks for faulting VMs
- One error-path lock imbalance fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZlisNHzgoq9nVg6g@fedora
drm/i915 fixes for v6.10-rc2:
- Fix a race in audio component by registering it later
- Make DPT object unshrinkable to avoid shrinking when framebuffer has
not shrunk
- Fix CCS id calculation to fix a perf regression
- Fix selftest caching mode
- Fix FIELD_PREP compiler warnings
- Fix indefinite wait for GT wakeref release
- Revert overeager multi-gt pm reference removal
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87a5k7iwod.fsf@intel.com
A zoned device may have a last sequential write required zone that is
smaller than other zones. However, all tests to check if a zone write
plug write offset exceeds the zone capacity use the same capacity
value stored in the gendisk zone_capacity field. This is incorrect for a
zoned device with a last runt (smaller) zone.
Add the new field last_zone_capacity to struct gendisk to store the
capacity of the last zone of the device. blk_revalidate_seq_zone() and
blk_revalidate_conv_zone() are both modified to get this value when
disk_zone_is_last() returns true. Similarly to zone_capacity, the value
is first stored using the last_zone_capacity field of struct
blk_revalidate_zone_args. Once zone revalidation of all zones is done,
this is used to set the gendisk last_zone_capacity field.
The checks to determine if a zone is full or if a sector offset in a
zone exceeds the zone capacity in disk_should_remove_zone_wplug(),
disk_zone_wplug_abort_unaligned(), blk_zone_write_plug_init_request(),
and blk_zone_wplug_prepare_bio() are modified to use the new helper
functions disk_zone_is_full() and disk_zone_wplug_is_full().
disk_zone_is_full() uses the zone index to determine if the zone being
tested is the last one of the disk and uses the either the disk
zone_capacity or last_zone_capacity accordingly.
Fixes: dd291d77cc ("block: Introduce zone write plugging")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20240530054035.491497-4-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit ecfe43b11b ("block: Remember zone capacity when revalidating
zones") introduced checks to ensure that the capacity of the zones of
a zoned device is constant for all zones. However, this check ignores
the possibility that a zoned device has a smaller last zone with a size
not equal to the capacity of other zones. Such device correspond in
practice to an SMR drive with a smaller last zone and all zones with a
capacity equal to the zone size, leading to the last zone capacity being
different than the capacity of other zones.
Correctly handle such device by fixing the check for the constant zone
capacity in blk_revalidate_seq_zone() using the new helper function
disk_zone_is_last(). This helper function is also used in
blk_revalidate_zone_cb() when checking the zone size.
Fixes: ecfe43b11b ("block: Remember zone capacity when revalidating zones")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20240530054035.491497-3-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A zoned device with a smaller last zone together with a zone capacity
smaller than the zone size does make any sense as that does not
correspond to any possible setup for a real device:
1) For ZNS and zoned UFS devices, all zones are always the same size.
2) For SMR HDDs, all zones always have the same capacity.
In other words, if we have a smaller last runt zone, then this zone
capacity should always be equal to the zone size.
Add a check in null_init_zoned_dev() to prevent a configuration to have
both a smaller zone size and a zone capacity smaller than the zone size.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240530054035.491497-2-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
syzbot reports that recv is using an uninitialized value:
=====================================================
BUG: KMSAN: uninit-value in io_req_cqe_overflow io_uring/io_uring.c:810 [inline]
BUG: KMSAN: uninit-value in io_req_complete_post io_uring/io_uring.c:937 [inline]
BUG: KMSAN: uninit-value in io_issue_sqe+0x1f1b/0x22c0 io_uring/io_uring.c:1763
io_req_cqe_overflow io_uring/io_uring.c:810 [inline]
io_req_complete_post io_uring/io_uring.c:937 [inline]
io_issue_sqe+0x1f1b/0x22c0 io_uring/io_uring.c:1763
io_wq_submit_work+0xa17/0xeb0 io_uring/io_uring.c:1860
io_worker_handle_work+0xc04/0x2000 io_uring/io-wq.c:597
io_wq_worker+0x447/0x1410 io_uring/io-wq.c:651
ret_from_fork+0x6d/0x90 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
Uninit was stored to memory at:
io_req_set_res io_uring/io_uring.h:215 [inline]
io_recv_finish+0xf10/0x1560 io_uring/net.c:861
io_recv+0x12ec/0x1ea0 io_uring/net.c:1175
io_issue_sqe+0x429/0x22c0 io_uring/io_uring.c:1751
io_wq_submit_work+0xa17/0xeb0 io_uring/io_uring.c:1860
io_worker_handle_work+0xc04/0x2000 io_uring/io-wq.c:597
io_wq_worker+0x447/0x1410 io_uring/io-wq.c:651
ret_from_fork+0x6d/0x90 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
Uninit was created at:
slab_post_alloc_hook mm/slub.c:3877 [inline]
slab_alloc_node mm/slub.c:3918 [inline]
__do_kmalloc_node mm/slub.c:4038 [inline]
__kmalloc+0x6e4/0x1060 mm/slub.c:4052
kmalloc include/linux/slab.h:632 [inline]
io_alloc_async_data+0xc0/0x220 io_uring/io_uring.c:1662
io_msg_alloc_async io_uring/net.c:166 [inline]
io_recvmsg_prep_setup io_uring/net.c:725 [inline]
io_recvmsg_prep+0xbe8/0x1a20 io_uring/net.c:806
io_init_req io_uring/io_uring.c:2135 [inline]
io_submit_sqe io_uring/io_uring.c:2182 [inline]
io_submit_sqes+0x1135/0x2f10 io_uring/io_uring.c:2335
__do_sys_io_uring_enter io_uring/io_uring.c:3246 [inline]
__se_sys_io_uring_enter+0x40f/0x3c80 io_uring/io_uring.c:3183
__x64_sys_io_uring_enter+0x11f/0x1a0 io_uring/io_uring.c:3183
x64_sys_call+0x2c0/0x3b50 arch/x86/include/generated/asm/syscalls_64.h:427
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
which appears to be io_recv_finish() reading kmsg->msg.msg_inq to decide
if it needs to set IORING_CQE_F_SOCK_NONEMPTY or not. If the recv is
entered with buffer selection, but no buffer is available, then we jump
error path which calls io_recv_finish() without having assigned
kmsg->msg_inq. This might cause an errant setting of the NONEMPTY flag
for a request get gets errored with -ENOBUFS.
Reported-by: syzbot+b1647099e82b3b349fbf@syzkaller.appspotmail.com
Fixes: 4a3223f7bf ("io_uring/net: switch io_recv() to using io_async_msghdr")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Several serieses of fixes that have come in since the merge window,
mostly for Intel systems. The biggest thing is some updates from Peter
which fix support for a series of Intel laptops which have been found to
use 16 bit rather than 32 bit DMIC configuration blobs in their firmware
descriptions. We also have a bunch of fixes for module annotations, and
some smaller single patch fixes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmZYoFgACgkQJNaLcl1U
h9DDYAf8C/m5RKsCXN22QzMACoP1r0ah9fDy26PZ2l+ftfS2a+uVLogwPovLFw1C
nlAbRc9hPEQjtI6mkCPeZjqBd7CGRcs84+wyoWOPZpyLd4uJ+bIh/NUmzYmb98pI
WuFcWPLoMSsOLlFMWKkkrTelESyvdRXVPE1re1QCb69X1zhkyK+yygYS9opSMIyS
v39kFfAcH8oWdPe4EUwjRREKY1gv47yzU4ilfJDRwrd8gcvtEX4qz3qv61p8xvoZ
Qm0a6p/35lLXNiJODP6BuafLN73CWWHbLFptgtrGJvSpXJtZV3R9dIy0/0ETQnFB
L44iMUlcGrByNea8W+nAjgtHgYaQzA==
=7p7n
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.10-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.10
Several serieses of fixes that have come in since the merge window,
mostly for Intel systems. The biggest thing is some updates from Peter
which fix support for a series of Intel laptops which have been found to
use 16 bit rather than 32 bit DMIC configuration blobs in their firmware
descriptions. We also have a bunch of fixes for module annotations, and
some smaller single patch fixes.
Since commit 5acf491196 ("drm/msm: import gen_header.py script from Mesa"),
compilation is broken on machines having python versions older than 3.9
due to dependency on argparse.BooleanOptionalAction.
Switch to use simple bool for the validate flag to remove the dependency.
Fixes: 5acf491196 ("drm/msm: import gen_header.py script from Mesa")
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240507230440.3384949-1-quic_abhinavk@quicinc.com
The fully ordered versions of xchg[8|16]() using LR/SC lack the
necessary memory barriers to guarantee the order.
Fix this by matching what is already implemented in the fully ordered
versions of cmpxchg() using LR/SC.
Suggested-by: Andrea Parri <parri.andrea@gmail.com>
Reported-by: Andrea Parri <parri.andrea@gmail.com>
Closes: https://lore.kernel.org/linux-riscv/ZlYbupL5XgzgA0MX@andrea/T/#u
Fixes: a8ed2b7a2c ("riscv/cmpxchg: Implement xchg for variables of size 1 and 2")
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Andrea Parri <parri.andrea@gmail.com>
Link: https://lore.kernel.org/r/20240530145546.394248-1-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
We're stuck supporting scalar misaligned loads in userspace because they
were part of the ISA at the time we froze the uABI. That wasn't the
case for vector misaligned accesses, so depending on them
unconditionally is a userspace bug. All extant vector hardware traps on
these misaligned accesses.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240524185600.5919-1-palmer@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
HAVE_ARCH_HUGE_VMAP also works on XIP kernel, so remove its dependency on
!XIP_KERNEL.
This also fixes a boot problem for XIP kernel introduced by the commit in
"Fixes:". This commit used huge page mapping for vmemmap, but huge page
vmap was not enabled for XIP kernel.
Fixes: ff172d4818 ("riscv: Use hugepage mappings for vmemmap")
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: <stable@vger.kernel.org>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20240526110104.470429-1-namcao@linutronix.de
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Top of the kernel thread stack should be reserved for pt_regs. However
this is not the case for the idle threads of the secondary boot harts.
Their stacks overlap with their pt_regs, so both may get corrupted.
Similar issue has been fixed for the primary hart, see c7cdd96eca
("riscv: prevent stack corruption by reserving task_pt_regs(p) early").
However that fix was not propagated to the secondary harts. The problem
has been noticed in some CPU hotplug tests with V enabled. The function
smp_callin stored several registers on stack, corrupting top of pt_regs
structure including status field. As a result, kernel attempted to save
or restore inexistent V context.
Fixes: 9a2451f186 ("RISC-V: Avoid using per cpu array for ordered booting")
Fixes: 2875fe0561 ("RISC-V: Add cpu_ops and modify default booting method")
Signed-off-by: Sergey Matyukevich <sergey.matyukevich@syntacore.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20240523084327.2013211-1-geomatsi@gmail.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The property name is "sensirion,low-precision", not
"sensicon,low-precision".
Cc: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Fixes: be7373b60d ("hwmon: shtc1: add support for device tree bindings")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The Intel N6000 BMC outputs the board power value in milliwatt, whereas
the hwmon sysfs interface must provide power values in microwatt.
Fixes: e1983220ae ("hwmon: intel-m10-bmc-hwmon: Add N6000 sensors")
Signed-off-by: Peter Colberg <peter.colberg@intel.com>
Reviewed-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Link: https://lore.kernel.org/r/20240521181246.683833-1-peter.colberg@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Current release - regressions:
- gro: initialize network_offset in network layer
- tcp: reduce accepted window in NEW_SYN_RECV state
Current release - new code bugs:
- eth: mlx5e: do not use ptp structure for tx ts stats when not initialized
- eth: ice: check for unregistering correct number of devlink params
Previous releases - regressions:
- bpf: Allow delete from sockmap/sockhash only if update is allowed
- sched: taprio: extend minimum interval restriction to entire cycle too
- netfilter: ipset: add list flush to cancel_gc
- ipv4: fix address dump when IPv4 is disabled on an interface
- sock_map: avoid race between sock_map_close and sk_psock_put
- eth: mlx5: use mlx5_ipsec_rx_status_destroy to correctly delete status rules
Previous releases - always broken:
- core: fix __dst_negative_advice() race
- bpf:
- fix multi-uprobe PID filtering logic
- fix pkt_type override upon netkit pass verdict
- netfilter: tproxy: bail out if IP has been disabled on the device
- af_unix: annotate data-race around unix_sk(sk)->addr
- eth: mlx5e: fix UDP GSO for encapsulated packets
- eth: idpf: don't enable NAPI and interrupts prior to allocating Rx buffers
- eth: i40e: fully suspend and resume IO operations in EEH case
- eth: octeontx2-pf: free send queue buffers incase of leaf to inner
- eth: ipvlan: dont Use skb->sk in ipvlan_process_v{4,6}_outbound
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=xkIZ
-----END PGP SIGNATURE-----
Merge tag 'net-6.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bpf and netfilter.
Current release - regressions:
- gro: initialize network_offset in network layer
- tcp: reduce accepted window in NEW_SYN_RECV state
Current release - new code bugs:
- eth: mlx5e: do not use ptp structure for tx ts stats when not
initialized
- eth: ice: check for unregistering correct number of devlink params
Previous releases - regressions:
- bpf: Allow delete from sockmap/sockhash only if update is allowed
- sched: taprio: extend minimum interval restriction to entire cycle
too
- netfilter: ipset: add list flush to cancel_gc
- ipv4: fix address dump when IPv4 is disabled on an interface
- sock_map: avoid race between sock_map_close and sk_psock_put
- eth: mlx5: use mlx5_ipsec_rx_status_destroy to correctly delete
status rules
Previous releases - always broken:
- core: fix __dst_negative_advice() race
- bpf:
- fix multi-uprobe PID filtering logic
- fix pkt_type override upon netkit pass verdict
- netfilter: tproxy: bail out if IP has been disabled on the device
- af_unix: annotate data-race around unix_sk(sk)->addr
- eth: mlx5e: fix UDP GSO for encapsulated packets
- eth: idpf: don't enable NAPI and interrupts prior to allocating Rx
buffers
- eth: i40e: fully suspend and resume IO operations in EEH case
- eth: octeontx2-pf: free send queue buffers incase of leaf to inner
- eth: ipvlan: dont Use skb->sk in ipvlan_process_v{4,6}_outbound"
* tag 'net-6.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (69 commits)
netdev: add qstat for csum complete
ipvlan: Dont Use skb->sk in ipvlan_process_v{4,6}_outbound
net: ena: Fix redundant device NUMA node override
ice: check for unregistering correct number of devlink params
ice: fix 200G PHY types to link speed mapping
i40e: Fully suspend and resume IO operations in EEH case
i40e: factoring out i40e_suspend/i40e_resume
e1000e: move force SMBUS near the end of enable_ulp function
net: dsa: microchip: fix RGMII error in KSZ DSA driver
ipv4: correctly iterate over the target netns in inet_dump_ifaddr()
net: fix __dst_negative_advice() race
nfc/nci: Add the inconsistency check between the input data length and count
MAINTAINERS: dwmac: starfive: update Maintainer
net/sched: taprio: extend minimum interval restriction to entire cycle too
net/sched: taprio: make q->picos_per_byte available to fill_sched_entry()
netfilter: nft_fib: allow from forward/input without iif selector
netfilter: tproxy: bail out if IP has been disabled on the device
netfilter: nft_payload: skbuff vlan metadata mangle support
net: ti: icssg-prueth: Fix start counter for ft1 filter
sock_map: avoid race between sock_map_close and sk_psock_put
...
tl;dr: CPUs with CPUID.80000008H but without CPUID.01H:EDX[CLFSH]
will end up reporting cache_line_size()==0 and bad things happen.
Fill in a default on those to avoid the problem.
Long Story:
The kernel dies a horrible death if c->x86_cache_alignment (aka.
cache_line_size() is 0. Normally, this value is populated from
c->x86_clflush_size.
Right now the code is set up to get c->x86_clflush_size from two
places. First, modern CPUs get it from CPUID. Old CPUs that don't
have leaf 0x80000008 (or CPUID at all) just get some sane defaults
from the kernel in get_cpu_address_sizes().
The vast majority of CPUs that have leaf 0x80000008 also get
->x86_clflush_size from CPUID. But there are oddballs.
Intel Quark CPUs[1] and others[2] have leaf 0x80000008 but don't set
CPUID.01H:EDX[CLFSH], so they skip over filling in ->x86_clflush_size:
cpuid(0x00000001, &tfms, &misc, &junk, &cap0);
if (cap0 & (1<<19))
c->x86_clflush_size = ((misc >> 8) & 0xff) * 8;
So they: land in get_cpu_address_sizes() and see that CPUID has level
0x80000008 and jump into the side of the if() that does not fill in
c->x86_clflush_size. That assigns a 0 to c->x86_cache_alignment, and
hilarity ensues in code like:
buffer = kzalloc(ALIGN(sizeof(*buffer), cache_line_size()),
GFP_KERNEL);
To fix this, always provide a sane value for ->x86_clflush_size.
Big thanks to Andy Shevchenko for finding and reporting this and also
providing a first pass at a fix. But his fix was only partial and only
worked on the Quark CPUs. It would not, for instance, have worked on
the QEMU config.
1. https://raw.githubusercontent.com/InstLatx64/InstLatx64/master/GenuineIntel/GenuineIntel0000590_Clanton_03_CPUID.txt
2. You can also get this behavior if you use "-cpu 486,+clzero"
in QEMU.
[ dhansen: remove 'vp_bits_from_cpuid' reference in changelog
because bpetkov brutally murdered it recently. ]
Fixes: fbf6449f84 ("x86/sev-es: Set x86_virt_bits to the correct value straight away, instead of a two-phase approach")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jörn Heusipp <osmanx@heusipp.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240516173928.3960193-1-andriy.shevchenko@linux.intel.com/
Link: https://lore.kernel.org/lkml/5e31cad3-ad4d-493e-ab07-724cfbfaba44@heusipp.de/
Link: https://lore.kernel.org/all/20240517200534.8EC5F33E%40davehans-spike.ostc.intel.com
kmemleak shows that there is a memory leak in io_uring read operation,
where a buffer is allocated at iovec import, but never de-allocated.
The memory is allocated at io_async_rw->free_iovec, but, then
io_async_rw is kfreed, taking the allocated memory with it. I saw this
happening when the read operation fails with -11 (EAGAIN).
This is the kmemleak splat.
unreferenced object 0xffff8881da591c00 (size 256):
...
backtrace (crc 7a15bdee):
[<00000000256f2de4>] __kmalloc+0x2d6/0x410
[<000000007a9f5fc7>] iovec_from_user.part.0+0xc6/0x160
[<00000000cecdf83a>] __import_iovec+0x50/0x220
[<00000000d1d586a2>] __io_import_iovec+0x13d/0x220
[<0000000054ee9bd2>] io_prep_rw+0x186/0x340
[<00000000a9c0372d>] io_prep_rwv+0x31/0x120
[<000000001d1170b9>] io_prep_readv+0xe/0x30
[<0000000070b8eb67>] io_submit_sqes+0x1bd/0x780
[<00000000812496d4>] __do_sys_io_uring_enter+0x3ed/0x5b0
[<0000000081499602>] do_syscall_64+0x5d/0x170
[<00000000de1c5a4d>] entry_SYSCALL_64_after_hwframe+0x76/0x7e
This occurs because the async data cleanup functions are not set for
read/write operations. As a result, the potentially allocated iovec in
the rw async data is not freed before the async data is released,
leading to a memory leak.
With this following patch, kmemleak does not show the leaked memory
anymore, and all liburing tests pass.
Fixes: a9165b83c1 ("io_uring/rw: always setup io_async_rw for read/write requests")
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240530142340.1248216-1-leitao@debian.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The new AMD/HYGON topology parser evaluates the SMT information in CPUID leaf
0x8000001e unconditionally while the original code restricted it to CPUs with
family 0x17 and greater.
This breaks family 0x15 CPUs which advertise that leaf and have a non-zero
value in the SMT section. The machine boots, but the scheduler complains loudly
about the mismatch of the core IDs:
WARNING: CPU: 1 PID: 0 at kernel/sched/core.c:6482 sched_cpu_starting+0x183/0x250
WARNING: CPU: 0 PID: 1 at kernel/sched/topology.c:2408 build_sched_domains+0x76b/0x12b0
Add the condition back to cure it.
[ bp: Make it actually build because grandpa is not concerned with
trivial stuff. :-P ]
Fixes: f7fb3b2dd9 ("x86/cpu: Provide an AMD/HYGON specific topology parser")
Closes: https://gitlab.archlinux.org/archlinux/packaging/packages/linux/-/issues/56
Reported-by: Tim Teichmann <teichmanntim@outlook.de>
Reported-by: Christian Heusel <christian@heusel.eu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Tim Teichmann <teichmanntim@outlook.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/7skhx6mwe4hxiul64v6azhlxnokheorksqsdbp7qw6g2jduf6c@7b5pvomauugk
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
The existing logic to pick a DMIC blob is based on several historical
assumptions that the NHLT in BIOS always contains 32-bits per sample
type (first patch, [1]).
The other issue with the existing logic is that it was designed to care only
about the bit depth of the format and fails to find the existing and correct
blob when rate/channels are different on the FE side compared to what we should
be using on the DAI side (we have components in path which can change
rate/channel count).
These issues have not been observed in past but with new MTL based (Windows)
laptops and new topologies to enhance the audio quality, we started to see weird
issues around how our assumptions of vendors failed.
Since some NHLT blob handling cleanup has been done for 6.10, this series will
complete that work to cover even cases that we don't anticipate to see.
[1] https://github.com/thesofproject/linux/issues/4973
When building a 32-bit kernel, some toolchains do not allow mixing soft
float and hard float object files:
LD vmlinux.o
powerpc64le-unknown-linux-musl-ld: lib/test_fpu_impl.o uses hard float, arch/powerpc/kernel/udbg.o uses soft float
powerpc64le-unknown-linux-musl-ld: failed to merge target specific data of file lib/test_fpu_impl.o
make[2]: *** [scripts/Makefile.vmlinux_o:62: vmlinux.o] Error 1
make[1]: *** [Makefile:1152: vmlinux_o] Error 2
make: *** [Makefile:240: __sub-make] Error 2
This is not an issue when building a 64-bit kernel. To unbreak the
build, limit ARCH_HAS_KERNEL_FPU_SUPPORT to 64-bit kernels. This is okay
because the only real user of this option, amdgpu, was previously
limited to PPC64 anyway; see commit a28e4b672f ("drm/amd/display: use
ARCH_HAS_KERNEL_FPU_SUPPORT").
Fixes: 01db473e1a ("powerpc: implement ARCH_HAS_KERNEL_FPU_SUPPORT")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202405250851.Z4daYSWG-lkp@intel.com/
Reported-by: Guenter Roeck <linux@roeck-us.net>
Closes: https://lore.kernel.org/lkml/eeffaec3-df63-4e55-ab7a-064a65c00efa@roeck-us.net/
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240529162852.1209-1-samuel.holland@sifive.com
The 'ld' instruction requires a 4-byte aligned displacement because it
is a DS-form instruction. But the "m" asm constraint doesn't enforce
that.
Add a special case of __get_user_asm2_goto() so that the "YZ" constraint
can be used for "ld".
The "Z" constraint is documented in the GCC manual PowerPC machine
constraints, and specifies a "memory operand accessed with indexed or
indirect addressing". "Y" is not documented in the manual but specifies
a "memory operand for a DS-form instruction". Using both allows the
compiler to generate a DS-form "ld" or X-form "ldx" as appropriate.
The change has to be conditional on CONFIG_PPC_KERNEL_PREFIXED because
the "Y" constraint does not guarantee 4-byte alignment when prefixed
instructions are enabled.
No build errors have been reported due to this, but the possibility is
there depending on compiler code generation decisions.
Fixes: c20beffeec ("powerpc/uaccess: Use flexible addressing with __put_user()/__get_user()")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240529123029.146953-2-mpe@ellerman.id.au
Building ppc64le_defconfig with GCC 14 fails with assembler errors:
CC fs/readdir.o
/tmp/ccdQn0mD.s: Assembler messages:
/tmp/ccdQn0mD.s:212: Error: operand out of domain (18 is not a multiple of 4)
/tmp/ccdQn0mD.s:226: Error: operand out of domain (18 is not a multiple of 4)
... [6 lines]
/tmp/ccdQn0mD.s:1699: Error: operand out of domain (18 is not a multiple of 4)
A snippet of the asm shows:
# ../fs/readdir.c:210: unsafe_copy_dirent_name(dirent->d_name, name, namlen, efault_end);
ld 9,0(29) # MEM[(u64 *)name_38(D) + _88 * 1], MEM[(u64 *)name_38(D) + _88 * 1]
# 210 "../fs/readdir.c" 1
1: std 9,18(8) # put_user # *__pus_addr_52, MEM[(u64 *)name_38(D) + _88 * 1]
The 'std' instruction requires a 4-byte aligned displacement because
it is a DS-form instruction, and as the assembler says, 18 is not a
multiple of 4.
A similar error is seen with GCC 13 and CONFIG_UBSAN_SIGNED_WRAP=y.
The fix is to change the constraint on the memory operand to put_user(),
from "m" which is a general memory reference to "YZ".
The "Z" constraint is documented in the GCC manual PowerPC machine
constraints, and specifies a "memory operand accessed with indexed or
indirect addressing". "Y" is not documented in the manual but specifies
a "memory operand for a DS-form instruction". Using both allows the
compiler to generate a DS-form "std" or X-form "stdx" as appropriate.
The change has to be conditional on CONFIG_PPC_KERNEL_PREFIXED because
the "Y" constraint does not guarantee 4-byte alignment when prefixed
instructions are enabled.
Unfortunately clang doesn't support the "Y" constraint so that has to be
behind an ifdef.
Although the build error is only seen with GCC 13/14, that appears
to just be luck. The constraint has been incorrect since it was first
added.
Fixes: c20beffeec ("powerpc/uaccess: Use flexible addressing with __put_user()/__get_user()")
Cc: stable@vger.kernel.org # v5.10+
Suggested-by: Kewen Lin <linkw@gcc.gnu.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240529123029.146953-1-mpe@ellerman.id.au
It's not an error or exceptional situation when the hosting
environment does not expose a name for the LP/guest via RTAS or the
device tree. This happens with qemu when run without the '-name'
option. The message also lacks a newline. Remove it.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Fixes: eddaa9a402 ("powerpc/pseries: read the lpar name from the firmware")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240524-lparcfg-updates-v2-1-62e2e9d28724@linux.ibm.com
Currently we only check the bit depth value among to DAI formats, but other
parameters might be constant, like number of channels and/or rate.
In capture we use the fe params as a reference to find the format and blob
which should be used, but in the path we can have components which can
handle expanding/narrowing number of channels or do a resample.
In these cases the topology is expected to have 'fixed' parameter for
channels/rates/bit depth and the conversion to the fe format is going to
be done within the path.
In practice this patch fixes issues like:
All DMIC formats are fixed four channels
We have a component which converts the four channel to stereo
FE is opened with 2 channel
Even if we have the correct bit depth format and blob (for four channel) we
will still be looking for stereo configurations, which will fail.
Note: the adjustment of params have switched order with the checking of
single bit depth (needed for the NHLT blob fallback support). This change
is non function, just that if the sof_ipc4_narrow_params_to_format() would
fail, there is no point of checking the single bit depth.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://msgid.link/r/20240530111918.21974-6-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the duplicated code paths to check for single bit depth and to
update the params with storing the parameters needed by the function and
have a single code section.
No functional change but the code is easier to follow.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://msgid.link/r/20240530111918.21974-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename the sof_ipc4_copier_is_single_format() to
sof_ipc4_copier_is_single_bitdepth() to clear the confusion of the use of
'format' when we are querying information on the bit depth.
Format is used to describe a combination of parameters (rate, channels,
sample format / bit depth).
Rename the flags used to store the result at the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://msgid.link/r/20240530111918.21974-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Print out the number of channels for the format explicitly instead of
having the reader to understand how to interpret the ch_map and ch_cfg
values.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://msgid.link/r/20240530111918.21974-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ACPI NHLT table always had 32-bit DMIC blob even if 16-bit was also
present and taken as a 'rule' which obviously got broken and there is at
least one device on the market which ships with only 16-bit DMIC
configuration blob.
This corner case has never been supported and it is going to need topology
updates for DMIC copier to support multiple formats.
As for the kernel side: if the copier supports multiple formats and the
preferred 32-bit DMIC blob is not found then we will try to get a 16-bit
DMIC configuration and look for a 16-bit copier config.
Fixes: f9209644ae ("ASoC: SOF: ipc4-topology: Correct DAI copier config and NHLT blob request")
Link: https://github.com/thesofproject/linux/issues/4973
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://msgid.link/r/20240530111918.21974-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Recent commit 0cfe71f45f ("netdev: add queue stats") added
a lot of useful stats, but only those immediately needed by virtio.
Presumably virtio does not support CHECKSUM_COMPLETE,
so statistic for that form of checksumming wasn't included.
Other drivers will definitely need it, in fact we expect it
to be needed in net-next soon (mlx5). So let's add the definition
of the counter for CHECKSUM_COMPLETE to uAPI in net already,
so that the counters are in a more natural order (all subsequent
counters have not been present in any released kernel, yet).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Fixes: 0cfe71f45f ("netdev: add queue stats")
Link: https://lore.kernel.org/r/20240529163547.3693194-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We fixed the incorrect UMP type for system messages in the recent
commit, but it missed one place in system_ev_to_ump_midi1().
Fix it now.
Fixes: e9e02819a9 ("ALSA: seq: Automatic conversion of UMP events")
Fixes: c2bb79613fed ("ALSA: seq: Fix incorrect UMP type for system messages")
Link: https://lore.kernel.org/r/20240530101044.17524-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----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=cexP
-----END PGP SIGNATURE-----
Merge tag 'nf-24-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
Patch #1 syzbot reports that nf_reinject() could be called without
rcu_read_lock() when flushing pending packets at nfnetlink
queue removal, from Eric Dumazet.
Patch #2 flushes ipset list:set when canceling garbage collection to
reference to other lists to fix a race, from Jozsef Kadlecsik.
Patch #3 restores q-in-q matching with nft_payload by reverting
f6ae9f120d ("netfilter: nft_payload: add C-VLAN support").
Patch #4 fixes vlan mangling in skbuff when vlan offload is present
in skbuff, without this patch nft_payload corrupts packets
in this case.
Patch #5 fixes possible nul-deref in tproxy no IP address is found in
netdevice, reported by syzbot and patch from Florian Westphal.
Patch #6 removes a superfluous restriction which prevents loose fib
lookups from input and forward hooks, from Eric Garver.
My assessment is that patches #1, #2 and #5 address possible kernel
crash, anything else in this batch fixes broken features.
netfilter pull request 24-05-29
* tag 'nf-24-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nft_fib: allow from forward/input without iif selector
netfilter: tproxy: bail out if IP has been disabled on the device
netfilter: nft_payload: skbuff vlan metadata mangle support
netfilter: nft_payload: restore vlan q-in-q match support
netfilter: ipset: Add list flush to cancel_gc
netfilter: nfnetlink_queue: acquire rcu_read_lock() in instance_destroy_rcu()
====================
Link: https://lore.kernel.org/r/20240528225519.1155786-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The driver overrides the NUMA node id of the device regardless of
whether it knows its correct value (often setting it to -1 even though
the node id is advertised in 'struct device'). This can lead to
suboptimal configurations.
This patch fixes this behavior and makes the shared memory allocation
functions use the NUMA node id advertised by the underlying device.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/r/20240528170912.1204417-1-shayagr@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jacob Keller says:
====================
Intel Wired LAN Driver Updates 2024-05-28 (e1000e, i40e, ice) [part]
This series includes a variety of fixes that have been accumulating on the
Intel Wired LAN dev-queue.
Hui Wang provides a fix for suspend/resume on e1000e due to failure
to correctly setup the SMBUS in enable_ulp().
Thinh Tran provides a fix for EEH I/O suspend/resume on i40e to
ensure that I/O operations can continue after a resume. To avoid duplicate
code, the common logic is factored out of i40e_suspend and i40e_resume.
Paul Greenwalt provides a fix to correctly map the 200G PHY types to link
speeds in the ice driver.
Dave Ertman provides a fix correcting devlink parameter unregistration in
the event that the driver loads in safe mode and some of the parameters
were not registered.
====================
Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-0-dc8593d2bbc6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On module load, the ice driver checks for the lack of a specific PF
capability to determine if it should reduce the number of devlink params
to register. One situation when this test returns true is when the
driver loads in safe mode. The same check is not present on the unload
path when devlink params are unregistered. This results in the driver
triggering a WARN_ON in the kernel devlink code.
The current check and code path uses a reduction in the number of elements
reported in the list of params. This is fragile and not good for future
maintaining.
Change the parameters to be held in two lists, one always registered and
one dependent on the check.
Add a symmetrical check in the unload path so that the correct parameters
are unregistered as well.
Fixes: 109eb29172 ("ice: Add tx_scheduling_layers devlink param")
CC: Lukasz Czapnik <lukasz.czapnik@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-8-dc8593d2bbc6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 24407a01e5 ("ice: Add 200G speed/phy type use") added support
for 200G PHY speeds, but did not include the mapping of 200G PHY types
to link speed. As a result the driver is returning UNKNOWN link speed
when setting 200G ethtool advertised link modes.
To fix this add 200G PHY types to link speed mapping to
ice_get_link_speed_based_on_phy_type().
Fixes: 24407a01e5 ("ice: Add 200G speed/phy type use")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-5-dc8593d2bbc6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When EEH events occurs, the callback functions in the i40e, which are
managed by the EEH driver, will completely suspend and resume all IO
operations.
- In the PCI error detected callback, replaced i40e_prep_for_reset()
with i40e_io_suspend(). The change is to fully suspend all I/O
operations
- In the PCI error slot reset callback, replaced pci_enable_device_mem()
with pci_enable_device(). This change enables both I/O and memory of
the device.
- In the PCI error resume callback, replaced i40e_handle_reset_warning()
with i40e_io_resume(). This change allows the system to resume I/O
operations
Fixes: a5f3d2c17b ("powerpc/pseries/pci: Add MSI domains")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Robert Thomas <rob.thomas@ibm.com>
Signed-off-by: Thinh Tran <thinhtr@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-3-dc8593d2bbc6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
