time64_t is 64-bit width type, we are not supposed to supply lesser ones
as in the case of rpi_firmware_print_firmware_revision() after the commit
4a60f58ee0 ("ARM: bcm2835: Switch to use %ptT"). Use temporary variable
of time64_t type to correctly handle lesser types.
Fixes: 4a60f58ee0 ("ARM: bcm2835: Switch to use %ptT")
Reported-by: Stefan Wahren <wahrenst@gmx.net>
Reported-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Revieved-by: Petr Mladek <pmladek@suse.com>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Link: https://lore.kernel.org/r/20200616163139.4229-1-andriy.shevchenko@linux.intel.com
Use %ptT instead of open coded variant to print content of
time64_t type in human readable format.
Link: https://lore.kernel.org/r/20200415170046.33374-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Rewieved-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
The Raspberry Pi 4 gets its USB functionality from VL805, a PCIe chip
that implements xHCI. After a PCI reset, VL805's firmware may either be
loaded directly from an EEPROM or, if not present, by the SoC's
co-processor, VideoCore. RPi4's VideoCore OS contains both the non public
firmware load logic and the VL805 firmware blob. The function this patch
introduces triggers the aforementioned process.
Link: https://lore.kernel.org/r/20200505161318.26200-3-nsaenzjulienne@suse.de
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Since clk-raspberrypi is tied to the VC4 firmware instead of particular
hardware it's registration should be performed by the firmware driver.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The firmware-owned GPIO expander on RPi 3 B+ must be in same state
after a reboot as initial power on. Otherwise this would cause a
network boot failure of the BOOTROM. So inform the VC4 firmware to restore
the expander before doing a reboot.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Adopt the SPDX license identifier headers to ease license compliance
management.
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Commit a1547e0bca ("firmware: raspberrypi: Remove VLA usage")
moved away from VLA's to a fixed maximum size for mailbox data.
However, some mailbox calls use larger data buffers
than the maximum allowed in that change. This fix therefor
moves from using fixed buffers to kmalloc to ensure all sizes
are catered for.
There is some documentation, which is somewhat out of date,
on the mailbox calls here :
https://github.com/raspberrypi/firmware/wiki/Mailbox-property-interface
Fixes: a1547e0bca ("firmware: raspberrypi: Remove VLA usage")
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
We should never assume to get a reply from the firmware otherwise
the call could block forever and the user don't get informed. So
define a timeout of 1 sec and print a stacktrace once in the unlikely
case the timeout expired.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
In the quest to remove all stack VLA usage from the kernel[1], this
removes the VLA in favor of a maximum size and adds a sanity check.
Existing callers of the firmware interface never need more than 24
bytes (struct gpio_set_config). This chooses 32 just to stay ahead
of future growth.
v2: Fix the length passed to rpi_firmware_property_list (by anholt,
acked by Kees).
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Since the raspberrypi-hwmon driver is tied to the VC4 firmware instead of
particular hardware its registration should be in the firmware driver.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The firmware timestamp is an unsigned 32-bit value, but we copy it into
a signed 32-bit variable, so we can theoretically get an overflow in
the calculation when the timestamp is between 2038 and 2106.
This changes the temporary variable to time64_t and changes the deprecated
time_to_tm() over to time64_to_tm() accordingly.
There is still an overflow in y2106, but that is a limitation of the
firmware interface, not a kernel problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
This gives us a function for making mailbox property channel requests
of the firmware, which is most notable in that it will let us get and
set clock rates.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
