Current ssi.c has duplicated code to control BUSIF
over/under run interrupt.
This patch adds new rsnd_ssi_busif_err_irq_enable/disable()
and share the code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Yongbo Zhang <giraffesnn123@gmail.com>
Cc: Chen Li <licheng0822@thundersoft.com>
Link: https://lore.kernel.org/r/871rbl1jsb.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ssi.c clears BUSIF error status at __rsnd_ssi_interrupt(),
but its code is verbose.
This patch off-load it to rsnd_ssi_busif_err_status_clear().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/8735w11jso.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 66c705d07d ("SoC: rsnd: add interrupt support for SSI BUSIF
buffer") adds __rsnd_ssi_interrupt() checks for BUSIF status,
but is using "break" at for loop.
This means it is not checking all status. Let's check all BUSIF status.
Fixes: commit 66c705d07d ("SoC: rsnd: add interrupt support for SSI BUSIF buffer")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/874kgh1jsw.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd needs to call .prepare (P) for clock settings,
.trigger for playback start (S) and stop (E).
It should be called as below from SSI point of view.
P -> S -> E -> P -> S -> E -> ...
But, if you used MIXer, below case might happen
(2)
1: P -> S ---> E -> ...
2: P ----> S -> ...
(1) (3)
P(1) setups clock, but E(2) resets it. and starts playback (3).
In such case, it will reports "SSI parent/child should use same rate".
rsnd_ssi_master_clk_start() which is the main function at (P)
was called from rsnd_ssi_init() (= S) before,
but was moved by below patch to rsnd_soc_dai_prepare() (= P) to avoid
using clk_get_rate() which shouldn't be used under atomic context.
commit 4d230d1271 ("ASoC: rsnd: fixup not to call clk_get/set
under non-atomic")
Because of above patch, rsnd_ssi_master_clk_start() is now called at (P)
which is for non atomic context. But (P) is assuming that spin lock is
*not* used.
One issue now is rsnd_ssi_master_clk_start() is checking ssi->xxx
which should be protected by spin lock.
After above patch, adg.c had below patch for other reasons.
commit 06e8f5c842 ("ASoC: rsnd: don't call clk_get_rate()
under atomic context")
clk_get_rate() is used at probe() timing by this patch.
In other words, rsnd_ssi_master_clk_start() is no longer using
clk_get_rate() any more.
This means we can call it from rsnd_ssi_init() (= S) again which is
protected by spin lock.
This patch re-move it to under spin lock, and solves
1. checking ssi->xxx without spin lock issue.
2. clk setting / device start / device stop race condition.
Reported-by: Linh Phung T. Y. <linh.phung.jy@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/875z0x1jt5.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During the recent rewrite of the implicit feedback support, we've
tested to apply the implicit fb on BOSS devices, but it failed, as the
capture stream didn't start without the playback. As the end result,
it got another type of quirk for tying both streams but starts
playback always (commit 6234fdc1ce "ALSA: usb-audio: Quirk for BOSS
GT-001").
Meanwhile, Mike Oliphant has tested the real implicit feedback mode
for the playback again with the latest code, and found out that it
actually works if the initial feedback sync is skipped; that is, on
those BOSS devices, the playback stream has to be started at first
without waiting for the capture URB completions. Otherwise it gets
stuck. In the rest operations after the capture stream processed, we
can take them as the implicit feedback source.
This patch is an attempt to improve the support for BOSS devices with
the implicit feedback mode in the way described above. It adds a new
flag to snd_usb_audio, playback_first, indicating that the playback
stream starts without sync with the initial capture completion. This
flag is set in the quirk table with the new IMPLICIT_FB_BOTH type.
Reported-and-tested-by: Mike Oliphant <oliphant@nostatic.org>
Link: https://lore.kernel.org/r/20210414083255.9527-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's a bad idea to allocate big structures on the stack.
Mark the variables as static and add a note for the locking.
Fixes: 22d8de62f1 ("ALSA: control - add generic LED trigger module as the new control layer")
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20210414105858.1937710-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
An error path exited the function before freeing the allocated
"argv" variable.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYHY3LRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qigOAPwOvbUI9PQTW3hs16XHDGbgtzdzX6A7
kF7GlId5tXbZDwD/bW2gilFCjULCEPDuqsDy5EXrbZ7V7kulOfIw2e8CAQM=
=HwKu
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Fix a memory link in dyn_event_release().
An error path exited the function before freeing the allocated 'argv'
variable"
* tag 'trace-v5.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/dynevent: Fix a memory leak in an error handling path
The logic in connect() is currently written with the assumption that
xenbus_watch_pathfmt() will return an error for a node that does not
exist. This assumption is incorrect: xenstore does allow a watch to
be registered for a nonexistent node (and will send notifications
should the node be subsequently created).
As of commit 1f2565780 ("xen-netback: remove 'hotplug-status' once it
has served its purpose"), this leads to a failure when a domU
transitions into XenbusStateConnected more than once. On the first
domU transition into Connected state, the "hotplug-status" node will
be deleted by the hotplug_status_changed() callback in dom0. On the
second or subsequent domU transition into Connected state, the
hotplug_status_changed() callback will therefore never be invoked, and
so the backend will remain stuck in InitWait.
This failure prevents scenarios such as reloading the xen-netfront
module within a domU, or booting a domU via iPXE. There is
unfortunately no way for the domU to work around this dom0 bug.
Fix by explicitly checking for existence of the "hotplug-status" node,
thereby creating the behaviour that was previously assumed to exist.
Signed-off-by: Michael Brown <mbrown@fensystems.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
__vmx_handle_exit() uses vcpu->run->internal.ndata as an index for
an array access. Since vcpu->run is (can be) mapped to a user address
space with a writer permission, the 'ndata' could be updated by the
user process at anytime (the user process can set it to outside the
bounds of the array).
So, it is not safe that __vmx_handle_exit() uses the 'ndata' that way.
Fixes: 1aa561b1a4 ("kvm: x86: Add "last CPU" to some KVM_EXIT information")
Signed-off-by: Reiji Watanabe <reijiw@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <20210413154739.490299-1-reijiw@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After commit 0f6925b3e8 ("virtio_net: Do not pull payload in skb->head")
Guenter Roeck reported one failure in his tests using sh architecture.
After much debugging, we have been able to spot silent unaligned accesses
in inet_gro_receive()
The issue at hand is that upper networking stacks assume their header
is word-aligned. Low level drivers are supposed to reserve NET_IP_ALIGN
bytes before the Ethernet header to make that happen.
This patch hardens skb_gro_reset_offset() to not allow frag0 fast-path
if the fragment is not properly aligned.
Some arches like x86, arm64 and powerpc do not care and define NET_IP_ALIGN
as 0, this extra check will be a NOP for them.
Note that if frag0 is not used, GRO will call pskb_may_pull()
as many times as needed to pull network and transport headers.
Fixes: 0f6925b3e8 ("virtio_net: Do not pull payload in skb->head")
Fixes: 78a478d0ef ("gro: Inline skb_gro_header and cache frag0 virtual address")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If sctp_destroy_sock is called without sock_net(sk)->sctp.addr_wq_lock
held and sp->do_auto_asconf is true, then an element is removed
from the auto_asconf_splist without any proper locking.
This can happen in the following functions:
1. In sctp_accept, if sctp_sock_migrate fails.
2. In inet_create or inet6_create, if there is a bpf program
attached to BPF_CGROUP_INET_SOCK_CREATE which denies
creation of the sctp socket.
The bug is fixed by acquiring addr_wq_lock in sctp_destroy_sock
instead of sctp_close.
This addresses CVE-2021-23133.
Reported-by: Or Cohen <orcohen@paloaltonetworks.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Fixes: 6102365876 ("bpf: Add new cgroup attach type to enable sock modifications")
Signed-off-by: Or Cohen <orcohen@paloaltonetworks.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is more correct to use dev_kfree_skb_irq when packets are dropped,
and to use dev_consume_skb_irq when packets are consumed.
Fixes: 0d97338818 ("ibmvnic: Introduce xmit_more support using batched subCRQ hcalls")
Suggested-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, tcp_allowed_congestion_control is global and writable;
writing to it in any net namespace will leak into all other net
namespaces.
tcp_available_congestion_control and tcp_allowed_congestion_control are
the only sysctls in ipv4_net_table (the per-netns sysctl table) with a
NULL data pointer; their handlers (proc_tcp_available_congestion_control
and proc_allowed_congestion_control) have no other way of referencing a
struct net. Thus, they operate globally.
Because ipv4_net_table does not use designated initializers, there is no
easy way to fix up this one "bad" table entry. However, the data pointer
updating logic shouldn't be applied to NULL pointers anyway, so we
instead force these entries to be read-only.
These sysctls used to exist in ipv4_table (init-net only), but they were
moved to the per-net ipv4_net_table, presumably without realizing that
tcp_allowed_congestion_control was writable and thus introduced a leak.
Because the intent of that commit was only to know (i.e. read) "which
congestion algorithms are available or allowed", this read-only solution
should be sufficient.
The logic added in recent commit
31c4d2f160: ("net: Ensure net namespace isolation of sysctls")
does not and cannot check for NULL data pointers, because
other table entries (e.g. /proc/sys/net/netfilter/nf_log/) have
.data=NULL but use other methods (.extra2) to access the struct net.
Fixes: 9cb8e048e5 ("net/ipv4/sysctl: show tcp_{allowed, available}_congestion_control in non-initial netns")
Signed-off-by: Jonathon Reinhart <jonathon.reinhart@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hristo Venev says:
====================
net: Fix two use-after-free bugs
The two patches fix two use-after-free bugs related to cleaning up
network namespaces, one in sit and one in ip6_tunnel. They are easy to
trigger if the user has the ability to create network namespaces.
The bugs can be used to trigger null pointer dereferences. I am not
sure if they can be exploited further, but I would guess that they
can. I am not sending them to the mailing list without confirmation
that doing so would be OK.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to the sit case, we need to remove the tunnels with no
addresses that have been moved to another network namespace.
Fixes: 0bd8762824 ("ip6tnl: add x-netns support")
Signed-off-by: Hristo Venev <hristo@venev.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
A sit interface created without a local or a remote address is linked
into the `sit_net::tunnels_wc` list of its original namespace. When
deleting a network namespace, delete the devices that have been moved.
The following script triggers a null pointer dereference if devices
linked in a deleted `sit_net` remain:
for i in `seq 1 30`; do
ip netns add ns-test
ip netns exec ns-test ip link add dev veth0 type veth peer veth1
ip netns exec ns-test ip link add dev sit$i type sit dev veth0
ip netns exec ns-test ip link set dev sit$i netns $$
ip netns del ns-test
done
for i in `seq 1 30`; do
ip link del dev sit$i
done
Fixes: 5e6700b3bf ("sit: add support of x-netns")
Signed-off-by: Hristo Venev <hristo@venev.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
A for-loop is using a u8 loop counter that is being compared to
a u32 cmp_dcbcfg->numapp to check for the end of the loop. If
cmp_dcbcfg->numapp is larger than 255 then the counter j will wrap
around to zero and hence an infinite loop occurs. Fix this by making
counter j the same type as cmp_dcbcfg->numapp.
Addresses-Coverity: ("Infinite loop")
Fixes: aeac8ce864 ("ice: Recognize 860 as iSCSI port in CEE mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
pci_disable_device() called in __ixgbe_shutdown() decreases
dev->enable_cnt by 1. pci_enable_device_mem() which increases
dev->enable_cnt by 1, was removed from ixgbe_resume() in commit
6f82b25587 ("ixgbe: use generic power management"). This caused
unbalanced increase/decrease. So add pci_enable_device_mem() back.
Fix the following call trace.
ixgbe 0000:17:00.1: disabling already-disabled device
Call Trace:
__ixgbe_shutdown+0x10a/0x1e0 [ixgbe]
ixgbe_suspend+0x32/0x70 [ixgbe]
pci_pm_suspend+0x87/0x160
? pci_pm_freeze+0xd0/0xd0
dpm_run_callback+0x42/0x170
__device_suspend+0x114/0x460
async_suspend+0x1f/0xa0
async_run_entry_fn+0x3c/0xf0
process_one_work+0x1dd/0x410
worker_thread+0x34/0x3f0
? cancel_delayed_work+0x90/0x90
kthread+0x14c/0x170
? kthread_park+0x90/0x90
ret_from_fork+0x1f/0x30
Fixes: 6f82b25587 ("ixgbe: use generic power management")
Signed-off-by: Yongxin Liu <yongxin.liu@windriver.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ixgbe driver currently generates a NULL pointer dereference when
performing the ethtool loopback test. This is due to the fact that there
isn't a q_vector associated with the test ring when it is setup as
interrupts are not normally added to the test rings.
To address this I have added code that will check for a q_vector before
returning a napi_id value. If a q_vector is not present it will return a
value of 0.
Fixes: b02e5a0ebb ("xsk: Propagate napi_id to XDP socket Rx path")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When mmaping an extra device region verify that the region index
derived from the mmap offset is valid.
Fixes: a15b1883fe ("vfio_pci: Allow mapping extra regions")
Cc: stable@vger.kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Message-Id: <20210412214124.GA241759@lisa.in-ulm.de>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Commit 1a1c130ab7 ("ACPI: tables: x86: Reserve memory occupied by
ACPI tables") attempted to address an issue with reserving the memory
occupied by ACPI tables, but it broke the initrd-based table override
mechanism relied on by multiple users.
To restore the initrd-based ACPI table override functionality, move
the acpi_boot_table_init() invocation in setup_arch() on x86 after
the acpi_table_upgrade() one.
Fixes: 1a1c130ab7 ("ACPI: tables: x86: Reserve memory occupied by ACPI tables")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Hi Mark
This patch-set is for v2 of Multi-CPU/Codec support,
and some cleanups.
v1 had patch-conflict on simple-card / audio-graph with below.
v2 was solved it.
fa74c223b6
("ASoC: simple-card: fix possible uninitialized single_cpu local variable")
I want to add new audio-graph-card2 driver which can support
not only DPCM, but also Multi-CPU/Codec, and Codec2Codec.
And it is also supporting audio-graph-card2 base custom driver.
But before supporting such driver, we need to cleanup existing
simple-card / audio-graph, because these and new driver are
sharing code.
Link: https://lore.kernel.org/r/87wntmod33.wl-kuninori.morimoto.gx@renesas.com
Link: https://lore.kernel.org/r/20210408141639.GA39604@sirena.org.uk
Kuninori Morimoto (12):
ASoC: simple-card-utils: setup dai_props cpu_dai/codec_dai at initial timing
ASoC: simple-card-utils: remove li->dais/li->conf
ASoC: simple-card-utils: use for_each_prop_xxx()
ASoC: simple-card-utils: remove asoc_simple_parse_xxx()
ASoC: simple-card-utils: care multi DAI at asoc_simple_clean_reference()
ASoC: simple-card-utils: indicate dai_fmt if exist
ASoC: simple-card-utils: indicate missing CPU/Codec numbers for debug
ASoC: simple-card-utils: add simple_props_to_xxx() macro
ASoC: simple-card-utils: multi support at asoc_simple_canonicalize_cpu/platform()
ASoC: simple-card-utils: tidyup debug info for clock
ASoC: simple-card-utils: tidyup dev_dbg() to use 1 line
ASoC: simple-card-utils: tidyup asoc_simple_parse_convert()
include/sound/simple_card_utils.h | 107 ++++++++++------
sound/soc/generic/audio-graph-card.c | 64 ++++------
sound/soc/generic/simple-card-utils.c | 174 ++++++++++++++++----------
sound/soc/generic/simple-card.c | 70 ++++-------
4 files changed, 226 insertions(+), 189 deletions(-)
--
2.25.1
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Lifu <chenlifu@huawei.com>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20210409015953.259688-1-chenlifu@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
simple-card / audio-graph can use clock as dai->clk or dai->sysclk.
These related information should be indicated at same position.
This patch tidyup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87h7kcwf8t.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current asoc_simple_canonicalize_cpu/platform() is assuming single CPU,
single Platform, but we want to support Multi support.
This patch is prepare for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87im4swf8y.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We shouldn't use dai_props->cpus/codecs/cpu_dai/codec_dai/codec_conf
directly, because these are array to supporting multi CPU/Codec/Platform.
This patch adds asoc_link_to_xxx() macro for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87k0p8wf9b.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now ALSA is supporting multi-CPU/Codec,
thus, we want to know number of CPU/Codec when debugging.
This patch indicates it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87lf9owf9g.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC is now supporting multi DAI, but, current
simple-card / audio-graph are assuming fixed single DAI.
This patch cares multi DAI at asoc_simple_clean_reference()
for of_node_put().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o8ekwf9p.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC is now supporting multi DAI, but, current
simple-card / audio-graph are assuming fixed single DAI.
Now, asoc_simple_parse_xxx() macro is assuming single DAI.
To support multi-CPU/Codec, this patch unpack asoc_simple_parse_xxx()
macro, and uses "&dai_link->cpus[i]" instead of "dai_link->cpus".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pmz0wf9u.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC is now supporting multi DAI, but, current
simple-card / audio-graph are assuming fixed single DAI.
This patch uses for_each_prop_xxx() to support multi DAI.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r1jgwf9y.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
li->dais is same as number of CPU + Codec,
li->conf is same as number of Codec when dummy-Codec.
li->dais/li->conf are no longer needed.
This patch removes these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87sg3wwfa3.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We couldn't setup dai_props cpu_dai/codec_dai at the initial timing,
because "counting DAIs loop" and "detecting DAIs loop" were different.
But we can do it now, because these are using same loops.
This patch setups dai_props cpu_dai/codec_dai at the initial timing.
It can removes triky code from simple-card / audio-graph.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tuocwfa8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Previous fifo depth patch was only tested on axg, not g12 or sm1.
Of course, while adding hw_params dai callback for the axg, I forgot to do
the same for g12 and sm1, leaving the depth unset and breaking playback on
these SoCs.
Add hw_params callback to the g12 dai_ops to fix the problem.
Fixes: 6f68accaa8 ("ASoC: meson: axg-frddr: set fifo depth according to the period")
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210412132256.89920-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the current code, we have some assumption that the audio clock
selector has been set up implicitly and don't want to touch it unless
it's really needed for the fallback autoclock setup. This works for
most devices but some seem having a problem. Partially this was
covered for the devices with a single connector at the initialization
phase (commit 086b957cc1 "ALSA: usb-audio: Skip the clock selector
inquiry for single connections"), but also there are cases where the
wrong clock set up is kept silently. The latter seems to be the cause
of the noises on Behringer devices.
In this patch, we explicitly set up the audio clock selector whenever
the appropriate node is found.
Reported-by: Geraldo Nascimento <geraldogabriel@gmail.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199327
Link: https://lore.kernel.org/r/CAEsQvcvF7LnO8PxyyCxuRCx=7jNeSCvFAd-+dE0g_rd1rOxxdw@mail.gmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210413084152.32325-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If instruction being single stepped caused a page fault, the kprobes
is cancelled to let the page fault handler continue as a normal page
fault. But the local irqflags are disabled so cpu will restore pstate
with DAIF masked. After pagefault is serviced, the kprobes is
triggerred again, we overwrite the saved_irqflag by calling
kprobes_save_local_irqflag(). NOTE, DAIF is masked in this new saved
irqflag. After kprobes is serviced, the cpu pstate is retored with
DAIF masked.
This patch is inspired by one patch for riscv from Liao Chang.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lore.kernel.org/r/20210412174101.6bfb0594@xhacker.debian
Signed-off-by: Will Deacon <will@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Fix NAT IPv6 offload in the flowtable.
2) icmpv6 is printed as unknown in /proc/net/nf_conntrack.
3) Use div64_u64() in nft_limit, from Eric Dumazet.
4) Use pre_exit to unregister ebtables and arptables hooks,
from Florian Westphal.
5) Fix out-of-bound memset in x_tables compat match/target,
also from Florian.
6) Clone set elements expression to ensure proper initialization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
xt_compat_match/target_from_user doesn't check that zeroing the area
to start of next rule won't write past end of allocated ruleset blob.
Remove this code and zero the entire blob beforehand.
Reported-by: syzbot+cfc0247ac173f597aaaa@syzkaller.appspotmail.com
Reported-by: Andy Nguyen <theflow@google.com>
Fixes: 9fa492cdc1 ("[NETFILTER]: x_tables: simplify compat API")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add missing 't' in attrtype.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit fee2d54641 ("net: phy: marvell: mv88e6390 temperature
sensor reading"), Linux reports the temperature of Topaz hwmon as
constant -75°C.
This is because switches from the Topaz family (88E6141 / 88E6341) have
the address of the temperature sensor register different from Peridot.
This address is instead compatible with 88E1510 PHYs, as was used for
Topaz before the above mentioned commit.
Create a new mapping table between switch family and PHY ID for families
which don't have a model number. And define PHY IDs for Topaz and Peridot
families.
Create a new PHY ID and a new PHY driver for Topaz's internal PHY.
The only difference from Peridot's PHY driver is the HWMON probing
method.
Prior this change Topaz's internal PHY is detected by kernel as:
PHY [...] driver [Marvell 88E6390] (irq=63)
And afterwards as:
PHY [...] driver [Marvell 88E6341 Family] (irq=63)
Signed-off-by: Pali Rohár <pali@kernel.org>
BugLink: https://github.com/globalscaletechnologies/linux/issues/1
Fixes: fee2d54641 ("net: phy: marvell: mv88e6390 temperature sensor reading")
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
