mtk_setup_firmware() misses to call release_firmware() in an error
path. Jump to free_fw to fix it.
Fixes: 737cd06072 ("Bluetooth: btmtksdio: fix up firmware download sequence")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-07-31
Here's the main bluetooth-next pull request for 5.9:
- Fix firmware filenames for Marvell chipsets
- Several suspend-related fixes
- Addedd mgmt commands for runtime configuration
- Multiple fixes for Qualcomm-based controllers
- Add new monitoring feature for mgmt
- Fix handling of legacy cipher (E4) together with security level 4
- Add support for Realtek 8822CE controller
- Fix issues with Chinese controllers using fake VID/PID values
- Multiple other smaller fixes & improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Data RAM on the device have to be powered on before starting to download
the firmware.
Fixes: 9aebfd4a22 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices")
Co-developed-by: Mark Chen <Mark-YW.Chen@mediatek.com>
Signed-off-by: Mark Chen <Mark-YW.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds the missing MODULE_DEVICE_TABLE() for SDIO IDs. While certain
platforms using this driver indeed have HW issues causing problems if
the module is loaded too early - this should be handled from user-space
by blacklisting it or delaying the loading.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add runtime PM support to btmtksdio. With this way, there will be the
benefit of the device entering the more power saving state once it is
been a while data traffic is idle.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Accumulate hdev->stat.byte_rx only for valid packets as btmtkuart doing.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add a register bit definition about CHLPCR bit 8 because the bit is quite
different in the meaning between reading and writing that bit.
The patch adds a definition particularly for the bit read to avoid the
confusion about using write definition to read the bit.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
bt_dev logging macros already include a newline at each output
so drop these unnecessary additional newlines in the driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fixed all the below warnings. They would probably cause the following
error handling path would use the uninitialized value and then produce
unexpected behavior.
drivers/bluetooth/btmtksdio.c:470:2: warning: ‘old_len’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
print_hex_dump(KERN_ERR, "err sdio rx: ", DUMP_PREFIX_NONE, 4, 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
old_data, old_len, true);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/bluetooth/btmtksdio.c:376:15: note: ‘old_len’ was declared here
unsigned int old_len;
^~~~~~~
drivers/bluetooth/btmtksdio.c:470:2: warning: ‘old_data’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
print_hex_dump(KERN_ERR, "err sdio rx: ", DUMP_PREFIX_NONE, 4, 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
old_data, old_len, true);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/bluetooth/btmtksdio.c:375:17: note: ‘old_data’ was declared here
unsigned char *old_data;
^~~~~~~~
v2: Remove old_len and old_data because the error path for sdio_readsb also
seems wrong. And change the prefix from "mediatek" to "btmtksdio".
Fixes: d74eef2834b5 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Macro module_sdio_driver is used for drivers whose init and exit paths
only register and unregister to SDIO API. So remove boilerplate code to
make code simpler by using module_sdio_driver.
Suggested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds the support of enabling MT7663S and MT7668S SDIO-based
Bluetooth function.
There are quite many differences between MT766[3,8]S and standard
Bluetooth SDIO devices such as Type-A and Type-B devices. For example,
MT766[3,8]S have its own SDIO registers layout, definition, SDIO packet
format, and the specific flow should be programmed on them to complete
the device initialization and low power control and so on.
Currently, there are many independent programming sequences from the
transport which are exactly the same as the ones in btusb.c about MediaTek
support [1] and btmtkuart.c. We can try to split the transport independent
Bluetooth setups on the advance, place them into the common files and allow
varous transport drivers to reuse them in the future.
[1] http://lists.infradead.org/pipermail/linux-mediatek/2019-January/017074.html
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
