This reverts commit fdc2de8712 ("serial/8250:
Add support for NI-Serial PXI/PXIe+485 devices").
The commit fdc2de8712 ("serial/8250: Add support for NI-Serial
PXI/PXIe+485 devices") introduced a breakage on NI-Serial PXI(e)-RS485
devices, RS-232 variants have no issue. The Linux system can enumerate the
NI-Serial PXI(e)-RS485 devices, but it broke the R/W operation on the
ports.
However, the implementation is working on the NI internal Linux RT kernel
but it does not work in the Linux main tree kernel. This is only affecting
NI products, specifically the RS-485 variants. Reverting the upstream
until a proper implementation that can apply to both NI internal Linux
kernel and Linux mainline kernel is figured out.
Signed-off-by: Je Yen Tam <je.yen.tam@ni.com>
Fixes: fdc2de8712 ("serial/8250: Add support for NI-Serial PXI/PXIe+485 devices")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191127075301.9866-1-je.yen.tam@ni.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d21b0be246 ("vt: introduce unicode mode for /dev/vcs") guarded
against using devices containing attributes as this is not yet
implemented. It however failed to guard against writes to any devices
as this is also unimplemented.
Reported-by: Or Cohen <orcohen@paloaltonetworks.com>
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Cc: <stable@vger.kernel.org> # v4.19+
Cc: Jiri Slaby <jslaby@suse.com>
Fixes: d21b0be246 ("vt: introduce unicode mode for /dev/vcs")
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.1911051030580.30289@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- A comprehensive rewrite of the robust/PI futex code's exit handling
to fix various exit races. (Thomas Gleixner et al)
- Rework the generic REFCOUNT_FULL implementation using
atomic_fetch_* operations so that the performance impact of the
cmpxchg() loops is mitigated for common refcount operations.
With these performance improvements the generic implementation of
refcount_t should be good enough for everybody - and this got
confirmed by performance testing, so remove ARCH_HAS_REFCOUNT and
REFCOUNT_FULL entirely, leaving the generic implementation enabled
unconditionally. (Will Deacon)
- Other misc changes, fixes, cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
lkdtm: Remove references to CONFIG_REFCOUNT_FULL
locking/refcount: Remove unused 'refcount_error_report()' function
locking/refcount: Consolidate implementations of refcount_t
locking/refcount: Consolidate REFCOUNT_{MAX,SATURATED} definitions
locking/refcount: Move saturation warnings out of line
locking/refcount: Improve performance of generic REFCOUNT_FULL code
locking/refcount: Move the bulk of the REFCOUNT_FULL implementation into the <linux/refcount.h> header
locking/refcount: Remove unused refcount_*_checked() variants
locking/refcount: Ensure integer operands are treated as signed
locking/refcount: Define constants for saturation and max refcount values
futex: Prevent exit livelock
futex: Provide distinct return value when owner is exiting
futex: Add mutex around futex exit
futex: Provide state handling for exec() as well
futex: Sanitize exit state handling
futex: Mark the begin of futex exit explicitly
futex: Set task::futex_state to DEAD right after handling futex exit
futex: Split futex_mm_release() for exit/exec
exit/exec: Seperate mm_release()
futex: Replace PF_EXITPIDONE with a state
...
Do not try to handle keycodes that are too big, otherwise we risk doing
out-of-bounds writes:
BUG: KASAN: global-out-of-bounds in clear_bit include/asm-generic/bitops-instrumented.h:56 [inline]
BUG: KASAN: global-out-of-bounds in kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline]
BUG: KASAN: global-out-of-bounds in kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495
Write of size 8 at addr ffffffff89a1b2d8 by task syz-executor108/1722
...
kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline]
kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495
input_to_handler+0x3b6/0x4c0 drivers/input/input.c:118
input_pass_values.part.0+0x2e3/0x720 drivers/input/input.c:145
input_pass_values drivers/input/input.c:949 [inline]
input_set_keycode+0x290/0x320 drivers/input/input.c:954
evdev_handle_set_keycode_v2+0xc4/0x120 drivers/input/evdev.c:882
evdev_do_ioctl drivers/input/evdev.c:1150 [inline]
In this case we were dealing with a fuzzed HID device that declared over
12K buttons, and while HID layer should not be reporting to us such big
keycodes, we should also be defensive and reject invalid data ourselves as
well.
Reported-by: syzbot+19340dff067c2d3835c0@syzkaller.appspotmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191122204220.GA129459@dtor-ws
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently warn the user when tty->port is not set in tty_init_dev
yet. The warning says that the kernel will crash later. And it really
will only few lines below at:
tty->port->itty = tty;
So be nice and avoid the crash -- return an error instead. And update
the warning.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20191122101721.7222-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt clear flag register is a "write 1 to clear" register.
So, only writing ones allows to clear flags:
- Replace buggy stm32_clr_bits() by a simple write to clear error flags
- Replace useless read/modify/write stm32_set_bits() routine by a
simple write to clear TC (transfer complete) flag.
Fixes: 4f01d833fd ("serial: stm32: fix rx error handling")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1574323849-1909-1-git-send-email-fabrice.gasnier@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust indentation from seven spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191121132847.29015-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The argument 'inode' passed to tty_open_by_driver() was not being used.
Remove the extra argument.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20191120151709.14148-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191120133843.13189-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Any arm config which has 'CONFIG_MTD_ONENAND_SAMSUNG=m' and
'CONFIG_SERIAL_SAMSUNG=m' gives a build warning:
warning: same module names found:
drivers/tty/serial/samsung.ko
drivers/mtd/nand/onenand/samsung.ko
Rename both drivers/tty/serial/samsung.c to
drivers/tty/serial/samsung_tty.c and drivers/mtd/nand/onenand/samsung.c
drivers/mtd/nand/onenand/samsung_mtd.c to fix the warning.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/r/20191117202435.28127-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver forgets to call pm_runtime_disable in remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191118024833.21587-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PL011's ->flush_buffer() implementation releases and reacquires the port
lock. Due to a race condition here, data can end up being added to the
circular buffer but neither being discarded nor being sent out. This
leads to, for example, tcdrain(2) waiting indefinitely.
Process A Process B
uart_flush_buffer()
- acquire lock
- circ_clear
- pl011_flush_buffer()
-- release lock
-- dmaengine_terminate_all()
uart_write()
- acquire lock
- add chars to circ buffer
- start_tx()
-- start DMA
- release lock
-- acquire lock
-- turn off DMA
-- release lock
// Data in circ buffer but DMA is off
According to the comment in the code, the releasing of the lock around
dmaengine_terminate_all() is to avoid a deadlock with the DMA engine
callback. However, since the time this code was written, the DMA engine
API documentation seems to have been clarified to say that
dmaengine_terminate_all() (in the identically implemented but
differently named dmaengine_terminate_async() variant) does not wait for
any running complete callback to be completed and can even be called
from a complete callback. So there is no possibility of deadlock if the
DMA engine driver implements this API correctly.
So we should be able to just remove this release and reacquire of the
lock to prevent the aforementioned race condition.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191118092547.32135-1-vincent.whitchurch@axis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f33cf77661.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 62104b280a.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3b209d253e.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0379b1163e.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d338838c09.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a00d9db895.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running in M-mode we can't use SBI based drivers. Add a new
CONFIG_RISCV_SBI that drivers that do SBI calls can depend on
instead.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Change logic how console_port is setup by using CON_ENABLED flag
instead of index. There will be unique uart_console
structure that's why code can't use id for console_port
assignment.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1573555271-2579-1-git-send-email-shubhrajyoti.datta@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per Documentation/DMA-API-HOWTO.txt,
To unmap a scatterlist, just call:
dma_unmap_sg(dev, sglist, nents, direction);
.. note::
The 'nents' argument to the dma_unmap_sg call must be
the _same_ one you passed into the dma_map_sg call,
it should _NOT_ be the 'count' value _returned_ from the
dma_map_sg call.
However in the driver, priv->nent is directly assigned with value
returned from dma_map_sg, and dma_unmap_sg use priv->nent for unmap,
this breaks the API usage.
So introduce a new entry orig_nent to remember 'nents'.
Fixes: da3564ee02 ("pch_uart: add multi-scatter processing")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1573623259-6339-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dmaengine_prep_slave_sg needs to use sg count returned
by dma_map_sg, not use sport->dma_tx_nents, because the return
value of dma_map_sg is not always same with "nents".
Fixes: b4cdc8f61b ("serial: imx: add DMA support for imx6q")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1573108875-26530-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This means removing support for checking magic in amiserial.c
(SERIAL_PARANOIA_CHECK option), which was checking a magic field which
doesn't currently exist in the struct. That code hasn't built at least
since git.
Removing the definition from the header is safe anyway as that code was
from another driver and not including it.
Signed-off-by: Pascal Terjan <pterjan@google.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20191105192749.67533-1-pterjan@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dmaengine_prep_slave_sg needs to use sg count returned
by dma_map_sg, not use sport->dma_tx_nents, because the return
value of dma_map_sg is not always same with "nents".
When enabling iommu for lpuart + edma, iommu framework may concatenate
two sgs into one.
Fixes: 6250cc30c4 ("tty: serial: fsl_lpuart: Use scatter/gather DMA for Tx")
Cc: <stable@vger.kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1572932977-17866-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 7726fb53e7.
Jiri writes:
On 24. 09. 19, 11:25, Xiaoming Ni wrote:
> According to the comment of tty_port_destroy():
> When a port was initialized using tty_port_init, one has to destroy
> the port by tty_port_destroy();
It continues with a part saying:
Either indirectly by using tty_port refcounting
(tty_port_put) or directly if refcounting is not used.
So this should be reverted.
Cc: Xiaoming Ni <nixiaoming@huawei.com>
Reported-by: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver uses clk_prepare_enable in ulite_probe but uses clk_unprepare
in ulite_remove, which does not match.
Replace clk_unprepare with clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191101085433.10399-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As platform_get_irq() now prints an error when the interrupt does not
exist, this warnings are printed on bananapi-r2:
[ 4.935780] mt6577-uart 11004000.serial: IRQ index 1 not found
[ 4.962589] 11002000.serial: ttyS1 at MMIO 0x11002000 (irq = 202, base_baud = 1625000) is a ST16650V2
[ 4.972127] mt6577-uart 11002000.serial: IRQ index 1 not found
[ 4.998927] 11003000.serial: ttyS2 at MMIO 0x11003000 (irq = 203, base_baud = 1625000) is a ST16650V2
[ 5.008474] mt6577-uart 11003000.serial: IRQ index 1 not found
Fix this by calling platform_get_irq_optional() instead.
now it looks like this:
[ 4.872751] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191027062117.20389-1-frank-w@public-files.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the commit 7723f4c5ec ("driver core: platform: Add an error message
to platform_get_irq*()") platform_get_irq() started issuing an error message.
Thus, there is no need to have the same in the driver
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191023103558.51862-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hci_qca interfaces to the wcn3990 via a uart_dm on the msm8998 mtp and
Lenovo Miix 630 laptop. As part of initializing the wcn3990, hci_qca
disables flow, configures the uart baudrate, and then reenables flow - at
which point an event is expected to be received over the uart from the
wcn3990. It is observed that this event comes after the baudrate change
but before hci_qca re-enables flow. This is unexpected, and is a result of
msm_reset() being broken.
According to the uart_dm hardware documentation, it is recommended that
automatic hardware flow control be enabled by setting RX_RDY_CTL. Auto
hw flow control will manage RFR based on the configured watermark. When
there is space to receive data, the hw will assert RFR. When the watermark
is hit, the hw will de-assert RFR.
The hardware documentation indicates that RFR can me manually managed via
CR when RX_RDY_CTL is not set. SET_RFR asserts RFR, and RESET_RFR
de-asserts RFR.
msm_reset() is broken because after resetting the hardware, it
unconditionally asserts RFR via SET_RFR. This enables flow regardless of
the current configuration, and would undo a previous flow disable
operation. It should instead de-assert RFR via RESET_RFR to block flow
until the hardware is reconfigured. msm_serial should rely on the client
to specify that flow should be enabled, either via mctrl() or the termios
structure, and only assert RFR in response to those triggers.
Fixes: 04896a77a9 ("msm_serial: serial driver for MSM7K onboard serial peripheral.")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Gross <agross@kernel.org>
Link: https://lore.kernel.org/r/20191021154616.25457-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The build of xtensa allmodconfig gives warning of:
In function 'get_ports.isra.0':
warning: the frame size of 1040 bytes is larger than 1024 bytes
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20191018161712.27807-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commits adds RS485 support for LPUART hardware that uses 32-bit
registers. These are typically found in i.MX8 processors.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20191017141428.10330-3-philippe.schenker@toradex.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use define from the 32-bit register description UARTMODIR_* instead of
UARTMODEM_*. The value is the same, so there is no functional change.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20191017141428.10330-2-philippe.schenker@toradex.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently flow control is not working due to lpuart32_set_mctrl that is
clearing TXCTSE bit in all cases. This bit gets earlier setup by
lpuart32_set_termios.
As I read in Documentation set_mctrl is also not meant for hardware
flow control rather than gpio setting and clearing a RTS signal.
Therefore I guess it is safe to remove the whole code in
lpuart32_set_mctrl.
This was tested with console on a i.MX8QXP SoC.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20191017141428.10330-1-philippe.schenker@toradex.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have symbol namespaces, use them in MCB to not pollute the
default namespace with MCB internals.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Jessica Yu <jeyu@kernel.org>
Reviewed-by: Michael Moese <mmoese@suse.de>
Link: https://lore.kernel.org/r/20191016100158.1400-1-jthumshirn@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Multiple tty devices are have tty devices that handle the
PPPIOCGUNIT and PPPIOCGCHAN ioctls. To avoid adding a compat_ioctl
handler to each of those, add it directly in tty_compat_ioctl
so we can remove the calls from fs/compat_ioctl.c.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All users of this call are in socket or tty code, so handling
it there means we can avoid the table entry in fs/compat_ioctl.c.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: netdev@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This reverts commit 91daae0318.
The origin patch is causing an issue on r8a7791/koelsch and
r8a7795/salvator-xs platforms where cons->index is not initialized to
expected value.
It is safer to revert this patch for now till it is clear why this is
happening.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/59f51af6bb03fce823663764d17ad0291aa01ab2.1571222199.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current checking for failure on the number of ports fails when
-ENODEV is returned from the call to get_num_ports. Fix this by making
num_ports and loop counter i signed rather than unsigned ints. Also
add check for num_ports being less than zero to check for -ve error
returns.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: e2fea54e45 ("8250-men-mcb: add support for 16z025 and 16z057")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Michael Moese <mmoese@suse.de>
Link: https://lore.kernel.org/r/20191013220016.9369-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a one more step to consolidate Exar bits under 8250_exar umbrella.
This time we introduce a custom ->startup() callback where the Exar specific
settings are applied.
Cc: Robert Middleton <robert.middleton@rm5248.com>
Cc: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Cc: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191011115610.81507-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Code that iterates over all standard PCI BARs typically uses
PCI_STD_RESOURCE_END. However, that requires the unusual test
"i <= PCI_STD_RESOURCE_END" rather than something the typical
"i < PCI_STD_NUM_BARS".
Add a definition for PCI_STD_NUM_BARS and change loops to use the more
idiomatic C style to help avoid fencepost errors.
Link: https://lore.kernel.org/r/20190927234026.23342-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190927234308.23935-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190916204158.6889-3-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # arch/s390/
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> # video/fbdev/
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> # pci/controller/dwc/
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com> # scsi/pm8001/
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> # scsi/pm8001/
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # memstick/
When registering a serdev controller, ACPI needs to be checked for
devices attached to it. Currently, all immediate children of the ACPI
node of the controller are assumed to be UART client devices for this
controller. Furthermore, these devices are not searched elsewhere.
This is incorrect: Similar to SPI and I2C devices, the UART client
device definition (via UARTSerialBusV2) can reside anywhere in the ACPI
namespace as resource definition inside the _CRS method and points to
the controller via its ResourceSource field. This field may either
contain a fully qualified or relative path, indicating the controller
device. To address this, we need to walk over the whole ACPI namespace,
looking at each resource definition, and match the client device to the
controller via this field.
This patch is based on the existing acpi serial bus implementations in
drivers/i2c/i2c-core-acpi.c and drivers/spi/spi.c, specifically commit
4c3c59544f ("spi/acpi: enumerate all SPI
slaves in the namespace").
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20190924162226.1493407-1-luzmaximilian@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sirfsoc_usp and sirfsoc_uart objects are not
used outside of the drivers/tty/serial/sirfsoc_uart.o
so make them static. Fixes following sparse warnings:
drivers/tty/serial/sirfsoc_uart.h:123:30: warning: symbol 'sirfsoc_usp' was not declared. Should it be static?
drivers/tty/serial/sirfsoc_uart.h:189:30: warning: symbol 'sirfsoc_uart' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lore.kernel.org/r/20191009135356.11180-1-ben.dooks@codethink.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add system wakeup capability over UART RX line for wakeup capable UART.
When system is suspended, RX line act as an interrupt to wakeup system
for any communication requests from peer.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/1570700803-17566-1-git-send-email-akashast@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move ISR registration from startup to probe function to avoid registering
it everytime when the port open is called for driver.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/1570700763-17319-1-git-send-email-akashast@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All i.MX SoCs except i.MX1 have ONLY one necessary IRQ, use
platform_get_irq_optional() to get second/third IRQ which are
optional to avoid below error message during probe:
[ 0.726219] imx-uart 30860000.serial: IRQ index 1 not found
[ 0.731329] imx-uart 30860000.serial: IRQ index 2 not found
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1570614559-11900-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Old early platform device support is now sh-specific. Before moving on
to implementing new early platform framework based on real platform
devices, prefix all early platform symbols with 'sh_'.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/20191003092913.10731-3-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SuperH is the only user of the current implementation of early platform
device support. We want to introduce a more robust approach to early
probing. As the first step - move all the current early platform code
to arch/sh.
In order not to export internal drivers/base functions to arch code for
this temporary solution - copy the two needed routines for driver
matching from drivers/base/platform.c to arch/sh/drivers/platform_early.c.
Also: call early_platform_cleanup() from subsys_initcall() so that it's
called after all early devices are probed.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/20191003092913.10731-2-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two checks to see if the manual gpio is configured, but
these the check is seeing if the structure is NULL instead it
should check to see if there are CTS and/or RTS pins defined.
This patch uses checks for those individual pins instead of
checking for the structure itself to restore auto RTS/CTS.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Yegor Yefremov <yegorslists@googlemail.com>
Link: https://lore.kernel.org/r/20191006163314.23191-2-aford173@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using mctrl_gpio_to_gpiod, it dereferences gpios into a single
requested GPIO. This dereferencing can break if gpios is NULL,
so this patch adds a NULL check before dereferencing it. If
gpios is NULL, this function will also return NULL.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Yegor Yefremov <yegorslists@googlemail.com>
Link: https://lore.kernel.org/r/20191006163314.23191-1-aford173@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix incorrect read-modify-write sequence in lpuart_flush_buffer() that
was reading from UARTPFIFO and writing to UARTCFIFO instead of
operating solely on the latter.
Fixes: 9bc19af9da ("tty: serial: fsl_lpuart: Flush HW FIFOs in .flush_buffer")
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reported-by: Vivien Didelot <vivien.didelot@gmail.com>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Jiri Slaby <jslaby@suse.com>
Link: https://lore.kernel.org/r/20191004215537.5308-1-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix tty driver build on SPARC by not using __exitdata.
It appears that SPARC does not support section .exit.data.
Fixes these build errors:
`.exit.data' referenced in section `.exit.text' of drivers/tty/n_hdlc.o: defined in discarded section `.exit.data' of drivers/tty/n_hdlc.o
`.exit.data' referenced in section `.exit.text' of drivers/tty/n_hdlc.o: defined in discarded section `.exit.data' of drivers/tty/n_hdlc.o
`.exit.data' referenced in section `.exit.text' of drivers/tty/n_hdlc.o: defined in discarded section `.exit.data' of drivers/tty/n_hdlc.o
`.exit.data' referenced in section `.exit.text' of drivers/tty/n_hdlc.o: defined in discarded section `.exit.data' of drivers/tty/n_hdlc.o
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 063246641d ("format-security: move static strings to const")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lore.kernel.org/r/675e7bd9-955b-3ff3-1101-a973b58b5b75@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two parts which should be fixed. The first one is to assigned
uartps_major at the end of probe() to avoid complicated logic when
something fails.
The second part is initialized uartps_major number to 0 when last device is
removed. This will ensure that on next probe driver will ask for new
dynamic major number.
Fixes: ab26266601 ("serial: uartps: Use the same dynamic major number for all ports")
Reported-by: Paul Thomas <pthomas8589@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/d2652cda992833315c4f96f06953eb547f928918.1570194248.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the comment of tty_port_destroy():
When a port was initialized using tty_port_init, one has to destroy
the port by tty_port_destroy();
tty_port_init() is called in gsm_dlci_alloc()
so tty_port_destroy() needs to be called in gsm_dlci_free()
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Link: https://lore.kernel.org/r/1569317156-45850-1-git-send-email-nixiaoming@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have got existing macro to check for CONFIG option, use it.
Signed-off-by: Pavel Machek <pavel@denx.de>
Link: https://lore.kernel.org/r/20190924083244.GA4344@amd
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the SIRQ polarity for Aspeed AST24xx/25xx VUART configurable via
sysfs. This setting need to be changed on specific host platforms
depending on the selected host interface (LPC / eSPI).
The setting is configurable via sysfs rather than device-tree to stay in
line with other related configurable settings.
On AST2500 the VUART SIRQ polarity can be auto-configured by reading a
bit from a configuration register, e.g. the LPC/eSPI interface
configuration bit.
Tested: Verified on TYAN S7106 mainboard.
Signed-off-by: Oskar Senft <osk@google.com>
Link: https://lore.kernel.org/r/20190905144130.220713-1-osk@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call uart_unregister_driver() conditionally instead of
unconditionally, only if it has been previously registered.
This uses driver.state, just as the sh-sci.c driver does.
Fixes this null pointer dereference in tty_unregister_driver(),
since the 'driver' argument is null:
general protection fault: 0000 [#1] PREEMPT SMP KASAN PTI
RIP: 0010:tty_unregister_driver+0x25/0x1d0
Fixes: 238b8721a5 ("[PATCH] serial uartlite driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: stable <stable@vger.kernel.org>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Link: https://lore.kernel.org/r/9c8e6581-6fcc-a595-0897-4d90f5d710df@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following an incorrect indentation reported to me by Dan Carpenter, I
noticed that the SysRq lines were inherited from the lpuart driver[1] (note
how the 'continue' is aligned to 'sport->port.sysrq = 0') and we have never
actually tested the SysRq support.
'sport->sysrq = 0' is not necessary neither before nor after 'continue',
because sysrq will already be 0 after uart_handle_sysrq_char() will finish.
Also, since the LINFlexD driver never called uart_handle_break(), sysrq
would have never been set to a nonzero value, so uart_handle_sysrq_char()
was not going to do anything.
Break conditions are detected based on a null data byte along with a
framing error (stop bit sampled to 0).
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/tty/serial/fsl_lpuart.c?h=b3e3bf2ef2c74f5ce5c19510edbbb9bfc1d249c2#n659
Fixes: 09864c1cdf ("tty: serial: Add linflexuart driver for S32V234")
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190918184439.7465-1-stefan-gabriel.mirea@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As platform_get_irq() now prints an error when the interrupt does not
exist, scary warnings may be printed for optional interrupts:
sh-sci e6550000.serial: IRQ index 1 not found
sh-sci e6550000.serial: IRQ index 2 not found
sh-sci e6550000.serial: IRQ index 3 not found
sh-sci e6550000.serial: IRQ index 4 not found
sh-sci e6550000.serial: IRQ index 5 not found
Fix this by calling platform_get_irq_optional() instead for all but the
first interrupts, which are optional.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191001180743.1041-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sifive serial driver implements earlycon support, but unless
another driver is built in that supports earlycon support it won't
be usable. Explicitly select SERIAL_EARLYCON instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Link: https://lore.kernel.org/r/20190910055923.28384-1-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the code which fetches the input clock by using
devm_clk_get_optional(). This comes with a small functional change: previously
all errors were ignored except deferred probe. Now all errors are
treated as errors. If no input clock is present devm_clk_get_optional() will
return NULL instead of an error which matches the behavior of the old code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190925162617.30368-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices support MSI interrupts. Let's at least try to use them in
platforms that provide MSI capability.
While at that, remove the now duplicated code from qrp_serial_setup().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191001115825.795700-1-felipe.balbi@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pl011_dma_probe() is only used in pl011_dma_startup() which does only
exist when CONFIG_DMA_ENGINE=y, so remove the unused dummy version to
silence the warning.
Signed-off-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/1568726340-4518-1-git-send-email-cai@lca.pw
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reason for this patch is xilinx_uartps driver which create one dynamic
instance per IP with unique major and minor combinations. drv->nr is in
this case all the time setup to 1. That means that uport->line is all the
time setup to 0 and drv->tty_driver->name_base is doing shift in name to
for example ttyPS3.
register_console() is looping over console_cmdline array and looking for
proper name/index combination which is in our case ttyPS/3.
That's why every instance of driver needs to be registered with proper
combination of name/number (ttyPS/3). Using uport->line is doing
registration with ttyPS/0 which is wrong that's why proper console index
should be used which is in cons->index field.
Also it is visible that recording console should be done based on
information about console not about the port but in most cases numbers are
the same and xilinx_uartps is only one exception now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/4a877f1c7189a7c45b59a6ebfc3de607e8758949.1567434470.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use software emulated RS485 direction control to provide RS485 API
Currently it is not possible to use rs485 as pointer to
rs485_config struct in struct uart_port is NULL in case we
configure the port through device tree.
Signed-off-by: Heiko Schocher <hs@denx.de>
Link: https://lore.kernel.org/r/20190913050105.1132080-1-hs@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to access the UART without the interrupts, the kernel uses
the basic polling methods for IO with the device. With these methods
implemented, it is now possible to enable kgdb during early boot over serial.
Signed-off-by: Lanqing Liu <liuhhome@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/f112a741c053ac5fb0637e2f058be81e17f78ccc.1568862391.git.liuhhome@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using only 4 DMA periods for UART RX is very few if we have a high
frequency of small transfers - like in our case using Bluetooth with
many small packets via UART - causing many dma transfers but in each
only filling a fraction of a single buffer. Such a case may lead to
the situation that DMA RX transfer is triggered but no free buffer is
available. When this happens dma channel ist stopped - with the patch
"dmaengine: imx-sdma: fix dma freezes" temporarily only - with the
possible consequences that:
with disabled hw flow control:
If enough data is incoming on UART port the RX FIFO runs over and
characters will be lost. What then happens depends on upper layer.
with enabled hw flow control:
If enough data is incoming on UART port the RX FIFO reaches a level
where CTS is deasserted and remote device sending the data stops.
If it fails to stop timely the i.MX' RX FIFO may run over and data
get lost. Otherwise it's internal TX buffer may getting filled to
a point where it runs over and data is again lost. It depends on
the remote device how this case is handled and if it is recoverable.
Obviously we want to avoid having no free buffers available. So we
decrease the size of the buffers and increase their number and the
total buffer size.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20190923135916.1212-1-philipp.puschmann@emlix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull kernel lockdown mode from James Morris:
"This is the latest iteration of the kernel lockdown patchset, from
Matthew Garrett, David Howells and others.
From the original description:
This patchset introduces an optional kernel lockdown feature,
intended to strengthen the boundary between UID 0 and the kernel.
When enabled, various pieces of kernel functionality are restricted.
Applications that rely on low-level access to either hardware or the
kernel may cease working as a result - therefore this should not be
enabled without appropriate evaluation beforehand.
The majority of mainstream distributions have been carrying variants
of this patchset for many years now, so there's value in providing a
doesn't meet every distribution requirement, but gets us much closer
to not requiring external patches.
There are two major changes since this was last proposed for mainline:
- Separating lockdown from EFI secure boot. Background discussion is
covered here: https://lwn.net/Articles/751061/
- Implementation as an LSM, with a default stackable lockdown LSM
module. This allows the lockdown feature to be policy-driven,
rather than encoding an implicit policy within the mechanism.
The new locked_down LSM hook is provided to allow LSMs to make a
policy decision around whether kernel functionality that would allow
tampering with or examining the runtime state of the kernel should be
permitted.
The included lockdown LSM provides an implementation with a simple
policy intended for general purpose use. This policy provides a coarse
level of granularity, controllable via the kernel command line:
lockdown={integrity|confidentiality}
Enable the kernel lockdown feature. If set to integrity, kernel features
that allow userland to modify the running kernel are disabled. If set to
confidentiality, kernel features that allow userland to extract
confidential information from the kernel are also disabled.
This may also be controlled via /sys/kernel/security/lockdown and
overriden by kernel configuration.
New or existing LSMs may implement finer-grained controls of the
lockdown features. Refer to the lockdown_reason documentation in
include/linux/security.h for details.
The lockdown feature has had signficant design feedback and review
across many subsystems. This code has been in linux-next for some
weeks, with a few fixes applied along the way.
Stephen Rothwell noted that commit 9d1f8be5cf ("bpf: Restrict bpf
when kernel lockdown is in confidentiality mode") is missing a
Signed-off-by from its author. Matthew responded that he is providing
this under category (c) of the DCO"
* 'next-lockdown' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (31 commits)
kexec: Fix file verification on S390
security: constify some arrays in lockdown LSM
lockdown: Print current->comm in restriction messages
efi: Restrict efivar_ssdt_load when the kernel is locked down
tracefs: Restrict tracefs when the kernel is locked down
debugfs: Restrict debugfs when the kernel is locked down
kexec: Allow kexec_file() with appropriate IMA policy when locked down
lockdown: Lock down perf when in confidentiality mode
bpf: Restrict bpf when kernel lockdown is in confidentiality mode
lockdown: Lock down tracing and perf kprobes when in confidentiality mode
lockdown: Lock down /proc/kcore
x86/mmiotrace: Lock down the testmmiotrace module
lockdown: Lock down module params that specify hardware parameters (eg. ioport)
lockdown: Lock down TIOCSSERIAL
lockdown: Prohibit PCMCIA CIS storage when the kernel is locked down
acpi: Disable ACPI table override if the kernel is locked down
acpi: Ignore acpi_rsdp kernel param when the kernel has been locked down
ACPI: Limit access to custom_method when the kernel is locked down
x86/msr: Restrict MSR access when the kernel is locked down
x86: Lock down IO port access when the kernel is locked down
...
Even in this age, people are still making new serial port silicon,
why...
Anyway, here's the TTY and Serial driver update for 5.4-rc1. Lots of
changes in here for a number of embedded serial port devices that are
being worked on because people really like to see those console logs...
Other than that, nothing major here, no core tty changes that anyone
should care about.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXYIXfw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymmNACeIYq7038NXGBXBj1DfN90GeGNenwAnRkjzF+6
YwEhFRxOMglnbvDevgPU
=E6jv
-----END PGP SIGNATURE-----
Merge tag 'tty-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Even in this age, people are still making new serial port silicon,
why...
Anyway, here's the TTY and Serial driver update for 5.4-rc1. Lots of
changes in here for a number of embedded serial port devices that are
being worked on because people really like to see those console
logs...
Other than that, nothing major here, no core tty changes that anyone
should care about.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (125 commits)
serial: tegra: Add PIO mode support
serial: tegra: report clk rate errors
serial: tegra: add support to adjust baud rate
serial: tegra: DT for Adjusted baud rates
serial: tegra: add support to use 8 bytes trigger
serial: tegra: set maximum num of uart ports to 8
serial: tegra: check for FIFO mode enabled status
dt-binding: serial: tegra: add new chips
serial: tegra: report error to upper tty layer
serial: tegra: flush the RX fifo on frame error
serial: tegra: avoid reg access when clk disabled
serial: tegra: add support to ignore read
serial: sprd: correct the wrong sequence of arguments
dt-bindings: serial: Convert riscv,sifive-serial to json-schema
serial: max310x: turn off transmitter before activating AutoCTS or auto transmitter flow control
serial: max310x: Properly set flags in AutoCTS mode
tty: serial: fix platform_no_drv_owner.cocci warnings
dt-bindings: serial: Document Freescale LINFlexD UART
serial: fsl_linflexuart: Update compatible string
tty: n_gsm: avoid recursive locking with async port hangup
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXYAIeQAKCRBiEGxRG/Sl
2/SzAQDEnoNxzV/R5kWFd+2kmFeY3cll0d99KMrWJ8om+kje6QD/cXxZHzFm+T1L
UPF66k76oOODV7cyndjXnTnRXbeCRAM=
=Szby
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"In this cycle we've finally managed to contribute the patch set
sorting out LED naming issues. Besides that there are many changes
scattered among various LED class drivers and triggers.
LED naming related improvements:
- add new 'function' and 'color' fwnode properties and deprecate
'label' property which has been frequently abused for conveying
vendor specific names that have been available in sysfs anyway
- introduce a set of standard LED_FUNCTION* definitions
- introduce a set of standard LED_COLOR_ID* definitions
- add a new {devm_}led_classdev_register_ext() API with the
capability of automatic LED name composition basing on the
properties available in the passed fwnode; the function is
backwards compatible in a sense that it uses 'label' data, if
present in the fwnode, for creating LED name
- add tools/leds/get_led_device_info.sh script for retrieving LED
vendor, product and bus names, if applicable; it also performs
basic validation of an LED name
- update following drivers and their DT bindings to use the new LED
registration API:
- leds-an30259a, leds-gpio, leds-as3645a, leds-aat1290, leds-cr0014114,
leds-lm3601x, leds-lm3692x, leds-lp8860, leds-lt3593, leds-sc27xx-blt
Other LED class improvements:
- replace {devm_}led_classdev_register() macros with inlines
- allow to call led_classdev_unregister() unconditionally
- switch to use fwnode instead of be stuck with OF one
LED triggers improvements:
- led-triggers:
- fix dereferencing of null pointer
- fix a memory leak bug
- ledtrig-gpio:
- GPIO 0 is valid
Drop superseeded apu2/3 support from leds-apu since for apu2+ a newer,
more complete driver exists, based on a generic driver for the AMD
SOCs gpio-controller, supporting LEDs as well other devices:
- drop profile field from priv data
- drop iosize field from priv data
- drop enum_apu_led_platform_types
- drop superseeded apu2/3 led support
- add pr_fmt prefix for better log output
- fix error message on probing failure
Other misc fixes and improvements to existing LED class drivers:
- leds-ns2, leds-max77650:
- add of_node_put() before return
- leds-pwm, leds-is31fl32xx:
- use struct_size() helper
- leds-lm3697, leds-lm36274, leds-lm3532:
- switch to use fwnode_property_count_uXX()
- leds-lm3532:
- fix brightness control for i2c mode
- change the define for the fs current register
- fixes for the driver for stability
- add full scale current configuration
- dt: Add property for full scale current.
- avoid potentially unpaired regulator calls
- move static keyword to the front of declarations
- fix optional led-max-microamp prop error handling
- leds-max77650:
- add of_node_put() before return
- add MODULE_ALIAS()
- Switch to fwnode property API
- leds-as3645a:
- fix misuse of strlcpy
- leds-netxbig:
- add of_node_put() in netxbig_leds_get_of_pdata()
- remove legacy board-file support
- leds-is31fl319x:
- simplify getting the adapter of a client
- leds-ti-lmu-common:
- fix coccinelle issue
- move static keyword to the front of declaration
- leds-syscon:
- use resource managed variant of device register
- leds-ktd2692:
- fix a typo in the name of a constant
- leds-lp5562:
- allow firmware files up to the maximum length
- leds-an30259a:
- fix typo
- leds-pca953x:
- include the right header"
* tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (72 commits)
leds: lm3532: Fix optional led-max-microamp prop error handling
led: triggers: Fix dereferencing of null pointer
leds: ti-lmu-common: Move static keyword to the front of declaration
leds: lm3532: Move static keyword to the front of declarations
leds: trigger: gpio: GPIO 0 is valid
leds: pwm: Use struct_size() helper
leds: is31fl32xx: Use struct_size() helper
leds: ti-lmu-common: Fix coccinelle issue in TI LMU
leds: lm3532: Avoid potentially unpaired regulator calls
leds: syscon: Use resource managed variant of device register
leds: Replace {devm_}led_classdev_register() macros with inlines
leds: Allow to call led_classdev_unregister() unconditionally
leds: lm3532: Add full scale current configuration
dt: lm3532: Add property for full scale current.
leds: lm3532: Fixes for the driver for stability
leds: lm3532: Change the define for the fs current register
leds: lm3532: Fix brightness control for i2c mode
leds: Switch to use fwnode instead of be stuck with OF one
leds: max77650: Switch to fwnode property API
led: triggers: Fix a memory leak bug
...
The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody is
using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still in
active use and are converted to the ARCH_MULTIPLATFORM build, meaning
that we can compile a kernel that works on these along with most other
ARMv5 platforms. Changes toward that goal are also merged for IOP32x,
but additional work is needed to complete this. Patches for the
remaining ARMv5 platforms have started but need more work and some
testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform
and the move of the TI Davinci platform to a new clocksource driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=u+ew
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Arnd Bergmann:
"The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody
is using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still
in active use and are converted to the ARCH_MULTIPLATFORM build,
meaning that we can compile a kernel that works on these along with
most other ARMv5 platforms. Changes toward that goal are also merged
for IOP32x, but additional work is needed to complete this. Patches
for the remaining ARMv5 platforms have started but need more work and
some testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform and
the move of the TI Davinci platform to a new clocksource driver"
[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
buildable on other platforms through COMPILE_TEST, but that causes new
warnings that I most definitely do not want to see during the merge
window as that could hide other issues.
So the COMPILE_TEST option got disabled for them again - Linus ]
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
ARM: davinci: support multiplatform build for ARM v5
arm64: exynos: Enable exynos-chipid driver
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
ARM: imx: stop adjusting ar8031 phy tx delay
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: debug-ll: Add support for r7s9210
...
-----BEGIN PGP SIGNATURE-----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=L5e+
-----END PGP SIGNATURE-----
Merge tag 'please-pull-ia64_for_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 updates from Tony Luck:
"The big change here is removal of support for SGI Altix"
* tag 'please-pull-ia64_for_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux: (33 commits)
genirq: remove the is_affinity_mask_valid hook
ia64: remove CONFIG_SWIOTLB ifdefs
ia64: remove support for machvecs
ia64: move the screen_info setup to common code
ia64: move the ROOT_DEV setup to common code
ia64: rework iommu probing
ia64: remove the unused sn_coherency_id symbol
ia64: remove the SGI UV simulator support
ia64: remove the zx1 swiotlb machvec
ia64: remove CONFIG_ACPI ifdefs
ia64: remove CONFIG_PCI ifdefs
ia64: remove the hpsim platform
ia64: remove now unused machvec indirections
ia64: remove support for the SGI SN2 platform
drivers: remove the SGI SN2 IOC4 base support
drivers: remove the SGI SN2 IOC3 base support
qla2xxx: remove SGI SN2 support
qla1280: remove SGI SN2 support
misc/sgi-xp: remove SGI SN2 support
char/mspec: remove SGI SN2 support
...
Add PIO mode support in receive and transmit path with RX interrupt
trigger of 16 bytes for Tegra194 and older chips.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-13-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Standard UART controllers support +/-4% baud rate error tolerance.
Tegra186 only supports 0% to +4% error tolerance whereas other Tegra
chips support standard +/-4% rate. Add chip data for knowing error
tolerance level for each soc. Creating new compatible for Tegra194
chip as it supports baud rate error tolerance of -2 to +2%, different
from older chips.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-12-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to adjust baud rates to fall under supported tolerance
range through DT.
Tegra186 chip has a hardware issue resulting in frame errors when
tolerance level for baud rate is negative. Provided entries to adjust
baud rate to be within acceptable range and work with devices that
can send negative baud rate. Also report error when baud rate set is
out of tolerance range of controller updated in device tree.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-11-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set maximum number of UART ports to 8 as older chips have 5 ports and
Tergra186 and later chips will have 8 ports. Add this info to chip
data. Read device tree compatible of this driver and register uart
driver with max ports of matching chip data.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-8-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chips prior to Tegra186 needed delay of 3 UART clock cycles to avoid
data loss. This issue is fixed in Tegra186 and a new flag is added to
check if FIFO mode is enabled. chip data updated to check if this flag
is available for a chip. Tegra186 has new compatible to enable this
flag.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-7-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Report overrun/parity/frame/break errors to top tty layer. Add support
to ignore break character if IGNBRK is set.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-5-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FIFO reset/flush code implemented now does not follow programming
guidelines. RTS line has to be turned off while flushing FIFOs to
avoid new transfers. Also check LSR bits UART_LSR_TEMT and UART_LSR_DR
to confirm FIFOs are flushed.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-4-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This avoids two race conditions from the UART shutdown sequence both
leading to 'Machine check error in AXI2APB' and kernel oops.
One was that the clock was disabled before the DMA was terminated making
it possible for the DMA callbacks to be called after the clock was
disabled. These callbacks could write to the UART registers causing
timeout.
The second was that the clock was disabled before the UART was
completely flagged as closed. This is done after the shutdown is called
and a new write could be started after the clock was disabled.
tegra_uart_start_pio_tx could be called causing timeout.
Given that the baud rate is reset at the end of shutdown sequence, this
fix is to examine the baud rate to avoid register access from both race
conditions.
Besides, terminate the DMA before disabling the clock.
Signed-off-by: Ahung Cheng <ahcheng@nvidia.com>
Signed-off-by: Shardar Mohammed <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-3-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to ignore read characters if CREAD flag is not set.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-2-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sequence of arguments which was passed to handle_lsr_errors() didn't
match the parameters defined in that function, &lsr was passed to flag
and &flag was passed to lsr, this patch fixed that.
Fixes: b7396a38fb ("tty/serial: Add Spreadtrum sc9836-uart driver support")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190905074151.5268-1-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As documented in the data-sheet, the transmitter must be disabled before
activating AutoCTS or auto transmitter flow control. Accordingly, the
transmitter must be enabled after AutoCTS or auto transmitter flow
control gets deactivated.
Signed-off-by: Christoph Vogtländer <c.vogtlaender@sigma-surface-science.com>
Link: https://lore.kernel.org/r/20190904121746.4641-1-c.vogtlaender@sigma-surface-science.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 391f93f2ec ("serial: core: Rework hw-assisted flow control
support") has changed the way the AutoCTS mode is handled.
According to that change, serial drivers which enable H/W AutoCTS mode must
set UPSTAT_AUTORTS, UPSTAT_AUTOCTS and UPSTAT_AUTOXOFF to prevent the
serial core from inadvertently disabling RX or TX. This patch adds proper
handling of UPSTAT_AUTORTS, UPSTAT_AUTOCTS and UPSTAT_AUTOXOFF flags.
Signed-off-by: Christoph Vogtländer <c.vogtlaender@sigma-surface-science.com>
Link: https://lore.kernel.org/r/20190904121141.4570-1-c.vogtlaender@sigma-surface-science.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/tty/serial/fsl_linflexuart.c:907:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Fixes: b953815b819b ("tty: serial: Add linflexuart driver for S32V234")
CC: Stefan-gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Signed-off-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20190825142837.zt3hpa22c7iofg3v@48261080c7f1
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sprd serial console can work with only 26M fixed clock,
but the probe() is returning fail if the clock "enable" is not
configured in device tree.
This patch will fix the problem to let the uart device which is
used for console can be initialized even missing "enable" clock
configured in devicetree. We should make sure the debug function
as available as we can.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/20190826072929.7696-4-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use console_initcall to save the console index we selected on the
command line to sprd_console before probe finished. Thus we can
make different processes to the uart devices during initialization
according to whether it is used for console.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/20190826072929.7696-3-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling sprd_console_setup(), sprd_uart_port probably is NULL,
we should check that first instead of checking its items directly.
Also we should check membase to avoid accessing uart device before
its initialization finished.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/20190826072929.7696-2-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 18dfef9c7f ("serial: atmel: convert to irq handling
provided mctrl-gpio"), the GPIOs interrupts are handled by
mctrl_gpio_irq_handle().
So, atmel_get_lines_status() can be completely killed and replaced by :
atmel_uart_readl(port, ATMEL_US_CSR);
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20190826071752.30396-1-richard.genoud@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This should help to avoid unnecessary gaps in transmission while
adding little overhead due to low default Tx threshold level (2
bytes).
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1567017475-11919-6-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_set_termios(): avoid writing baud rate divider registers when the
values to be written are the same as current. Any writing seems to
restart transmission/receiving logic in the hardware, that leads to
data breakage even when rate doesn't in fact change. E.g., user
switches RTS/CTS handshake and suddenly gets broken bytes.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1567017475-11919-5-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_set_termios(): disabling individual interrupt requests in UART for
duration of the routine is pointless. Get rid of it.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1567017475-11919-4-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_set_termios(): stopping receiver and transmitter does harm when
something that doesn't touch transmission format/rate changes, such as
RTS/CTS handshake.
OTOH, it does no good on baud rate or format change, as
synchronization on upper-level protocols is still required to do it
right.
Therefore, just stop doing it.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1567017475-11919-3-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_set_termios(): remove busy-waiting "drain Tx FIFO" loop. Worse
yet, it was potentially unbounded wait due to RTS/CTS (hardware)
handshake.
Let user space ensure draining is done before termios change, if
draining is needed in the first place.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1567017475-11919-2-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent change split the insertion loop into two parts. The first part
accessed bytes 0, 1, ... (rxlen - 2), and the second part by mistake
took offset `rxlen` instead of the correct `rxlen - 1`. So one byte was
not stored, and the final access wrote past the end of the rx_buf.
Fixes: 9c12d739d6 (tty: max310x: Split uart characters insertion loop)
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/13ea227620aaad8a7231d42ed03a8508297d4eb3.1567027079.git.jan.kundrat@cesnet.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20190827114614.102037-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There may be setups, where legacy interrupts are not available. This is
the caese, e.g., when Linux runs as guest (aka. non-root cell) of the
partitioning hypervisor Jailhouse. There, only MSI(-X) interrupts are
available for guests.
But the 8250_pci driver currently only supports legacy ints. So let's
enable MSI(-X) interrupts.
Nevertheless, this needs to handled with care: while many 8250 devices
actually claim to support MSI(-X) interrupts it should not be enabled be
default. I had at least one device in my hands with broken MSI
implementation.
So better introduce a whitelist with devices that are known to support
MSI(-X) interrupts. I tested all devices mentioned in the patch.
Signed-off-by: Ralf Ramsauer <ralf.ramsauer@oth-regensburg.de>
Link: https://lore.kernel.org/r/20190812112152.693622-1-ralf.ramsauer@oth-regensburg.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81504A/508A/512A is PCIE to 4/8/12 UARTs device. It's support
IO/MMIO/PCIE conf to access all functions. The old F81504/508/512 is
only support IO.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Link: https://lore.kernel.org/r/1565933249-23076-1-git-send-email-hpeter+linux_kernel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Description of the modem line control GPIOs contain a boolean type to set
direction of the line. Since GPIO library provides an enumerator type of flags,
we may utilize it and allow a bit more flexibility on the choice of the type of
the line parameters. It also removes an additional layer of value conversion.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190814140759.17486-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_SERIAL_FSL_LINFLEXUART=y and CONFIG_PRINTK is not set,
one compilation error is found as below:
drivers/tty/serial/fsl_linflexuart.c: In function linflex_earlycon_putchar:
drivers/tty/serial/fsl_linflexuart.c:608:31: error: CONFIG_LOG_BUF_SHIFT undeclared
(first use in this function); did you mean CONFIG_ISA_BUS_API?
if (earlycon_buf.len >= 1 << CONFIG_LOG_BUF_SHIFT)
^~~~~~~~~~~~~~~~~~~~
CONFIG_ISA_BUS_API
This because CONFIG_LOG_BUF_SHIFT is depended on CONFIG_PRINTK, fix this
by adding dependence for CONFIG_SERIAL_FSL_LINFLEXUART.
Fixes: b953815b819b ("tty: serial: Add linflexuart driver for S32V234")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Link: https://lore.kernel.org/r/20190820124015.28409-1-maowenan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guessing the first tty for a gsm0710 multiplexed serial device is not
currently possible, which makes it racy to use with multiple modems.
Add a way to map the physical serial tty to its related mux devices
using an ioctl.
Signed-off-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/r/20190812211243.98686-1-martin@geanix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moxa serial boards only need a special setup function, we can use
generic 8250 framework for other parts.
So let's merge 8250_moxa to 8250_pci.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20190816165124.16942-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1d267ea653 ("serial: mctrl-gpio: simplify init
routine"), mctrl_gpio_init() returns failure if the assignment to any
member of the gpio array results in an error pointer.
Since commit c359522194593815 ("serial: mctrl_gpio: Avoid probe failures
in case of missing gpiolib"), mctrl_gpio_to_gpiod() returns NULL in the
!CONFIG_GPIOLIB case.
Hence there is no longer a need to check for mctrl_gpio_to_gpiod()
returning an error value. A simple NULL check is sufficient.
This follows the spirit of commit 445df7ff3f ("serial: mctrl-gpio:
drop usages of IS_ERR_OR_NULL") in the mctrl-gpio core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190814092924.13857-3-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1d267ea653 ("serial: mctrl-gpio: simplify init
routine"), mctrl_gpio_init() returns failure if the assignment to any
member of the gpio array results in an error pointer.
Since commit c359522194593815 ("serial: mctrl_gpio: Avoid probe failures
in case of missing gpiolib"), mctrl_gpio_to_gpiod() returns NULL in the
!CONFIG_GPIOLIB case.
Hence there is no longer a need to check for mctrl_gpio_to_gpiod()
returning an error value. A simple NULL check is sufficient.
This follows the spirit of commit 445df7ff3f ("serial: mctrl-gpio:
drop usages of IS_ERR_OR_NULL") in the mctrl-gpio core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190814092924.13857-4-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IER and DLH registers occupy the same address space, selected by
the LCR.DLAB bit. Hence, add port lock to protect IER when LCR.DLAB bit
is set.
Signed-off-by: Ahung Cheng <ahcheng@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/1565609303-27000-5-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the internal loopback functionality that can be enabled with
TIOCM_LOOP.
Signed-off-by: Andreas Abel <aabel@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/1565609303-27000-2-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When half-duplex RS485 communication is used, after RX is started, TX
tasklet still needs to be scheduled tasklet. This avoids console freezing
when more data is to be transmitted, if the serial communication is not
closed.
Fixes: 69646d7a36 ("tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped")
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190813074025.16218-1-razvan.stefanescu@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce support for LINFlex driver, based on:
- the version of Freescale LPUART driver after commit b3e3bf2ef2 ("Merge
4.0-rc7 into tty-next");
- commit abf1e0a980 ("tty: serial: fsl_lpuart: lock port on console
write").
In this basic version, the driver can be tested using initramfs and relies
on the clocks and pin muxing set up by U-Boot.
Remarks concerning the earlycon support:
- LinFlexD does not allow character transmissions in the INIT mode (see
section 47.4.2.1 in the reference manual[1]). Therefore, a mutual
exclusion between the first linflex_setup_watermark/linflex_set_termios
executions and linflex_earlycon_putchar was employed and the characters
normally sent to earlycon during initialization are kept in a buffer and
sent afterwards.
- Empirically, character transmission is also forbidden within the last 1-2
ms before entering the INIT mode, so we use an explicit timeout
(PREINIT_DELAY) between linflex_earlycon_putchar and the first call to
linflex_setup_watermark.
- U-Boot currently uses the UART FIFO mode, while this driver makes the
transition to the buffer mode. Therefore, the earlycon putchar function
matches the U-Boot behavior before initializations and the Linux behavior
after.
[1] https://www.nxp.com/webapp/Download?colCode=S32V234RM
Signed-off-by: Stoica Cosmin-Stefan <cosmin.stoica@nxp.com>
Signed-off-by: Adrian.Nitu <adrian.nitu@freescale.com>
Signed-off-by: Larisa Grigore <Larisa.Grigore@nxp.com>
Signed-off-by: Ana Nedelcu <B56683@freescale.com>
Signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Signed-off-by: Matthew Nunez <matthew.nunez@nxp.com>
[stefan-gabriel.mirea@nxp.com: Reduced for upstreaming and implemented
earlycon support]
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Link: https://lore.kernel.org/r/20190809112853.15846-6-stefan-gabriel.mirea@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable ret is initialized to a value that is never read and it
is re-assigned later. The initialization is redundant and can be
removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190809174042.6276-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to Sunix serial boards with up to 16 ports.
Sunix board need its own setup callback instead of using Timedia's, to
properly support more than 4 ports.
Cc: Morris Ku <morris_ku@sunix.com>
Cc: Debbie Liu <debbie_liu@sunix.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20190809190130.30773-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform is getting removed, so there are no more users
of this driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20190809202749.742267-3-arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver/IP is reused across multiple SoCs. Older SoCs supported three
separate IRQs for tx, rx & err interrupts. Newer Lightning Mountain SoC
supports single IRQ for all of tx/rx/err interrupts. This patch modifies
the driver design to support dynamic assignment of IRQ resources & ISRs
based on devicetree node compatible entries.
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/b166a0593bee191fcd77b5bdf8fedc6f6330a371.1565257887.git.rahul.tanwar@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use explicit string instead of a macro for devicetree compatible string.
This series of patches is to add support for multiple SoCs which reuse the same
serial controller IP. The following patches will add another compatible string
to support new Lightning Mountain(LGM) SoC. So it makes sense to have the
compatible strings explicitly mentioned instead of a fixed macro.
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/57e2b69e9fbd93328a477b4c7dd2dcc78784ecb1.1565257887.git.rahul.tanwar@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Elkhart Lake may use High Speed UART from OSE IP block.
This is different to what we have in main LPSS, though compatible
with older version of it, which is handled by this driver.
Enable OSE HS UART on Intel Elkhart Lake by adding PCI IDs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since PCI core provides a generic PCI_DEVICE_DATA() macro,
replace LPSS_DEVICE() with former one.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is really useful not only for debugging to have an DMA IRQ line and
pool being mapped to the corresponding IP by using its instance ID.
Provide PCI device and function as instance ID for Intel Quark UART DMA.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Synopsys DesignWare 8250 uart which version >= 4.00a, there's a
valid divisor latch fraction register.
Now the preparation is done, it's easy to add the feature support.
This patch firstly tries to get the fractional divisor width during
probe, then setups specific get_divisor() and set_divisor() hook.
Among other changes the FIFO size is now retrieved from the hardware.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have a common library module for Synopsys DesignWare UART,
let us use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have a common library module for Synopsys DesignWare UART,
let us use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We would like to use same functions in the couple of drivers for
Synopsys DesignWare 8250 UART. Split them from 8250_dw into new brand
library module which users will select explicitly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The use of pointer will simplify enabling runtime PM for the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 2cb78eab23 ("serial: 8250_dw: Use a unified new dev variable in
probe") introduced a local dev variable in ->probe(). Do the same in ->remove()
in order to prepare for sequential patches.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Link: https://lore.kernel.org/r/20190806094322.64987-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing driver can only support single core SoC. But new multicore
platforms which reuse the same driver/IP need SMP support. This patch adds
multicore support in the driver.
Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/7912786cccad60c72b20ea724af1def505ab22aa.1565160764.git.rahul.tanwar@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling TIE in .startup() callback causes the driver to start (or at
least try) to transmit data before .start_tx() is called. Which, while
harmless (since TIE handler will immediately disable it), is a no-op
and shouldn't really happen. Drop UARTCR2_TIE from list of bits set in
lpuart_startup().
This change will also not enable TIE in .resume(), but it seems that,
similart to .startup(), transmit interrupt shouldn't be enabled there
either.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190805185701.22863-6-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most users of lpuart*_setup_watermark() enable identical set of flags
right after the call, so combine those two action into a subroutine
and make use of it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190805185701.22863-5-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Code doing final steps of TX/RX configuration in lpuart32_startup()
and lpuart_resume() is identical, so move it into a standalone
subroutine.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190805185701.22863-4-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As explained in Documentation/timers/timers-howto.rst
the small amount of milliseconds sometimes produces
much longer delays.
Replace msleep(1) with usleep_range(1000, 1100).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190805142535.21948-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190802130817.16220-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the mctrl_gpio code returns NULL instead of ERR_PTR(-ENOSYS)
if CONFIG_GPIOLIB is disabled, we can safely remove this check.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Uwe Kleine-Knig <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20190802100349.8659-4-frieder.schrempf@kontron.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the mctrl_gpio code returns NULL instead of ERR_PTR(-ENOSYS)
if CONFIG_GPIOLIB is disabled, we can safely remove this check.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Uwe Kleine-Knig <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20190802100349.8659-3-frieder.schrempf@kontron.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_GPIOLIB is not enabled, mctrl_gpio_init() and
mctrl_gpio_init_noauto() will currently return an error pointer with
-ENOSYS. As the mctrl GPIOs are usually optional, drivers need to
check for this condition to allow continue probing.
To avoid the need for this check in each driver, we return NULL
instead, as all the mctrl_gpio_*() functions are skipped anyway.
We also adapt mctrl_gpio_to_gpiod() to be in line with this change.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Uwe Kleine-Knig <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20190802100349.8659-1-frieder.schrempf@kontron.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move INT0 clearing out of common, per-port serial8250_do_startup()
into PCI device probe/resume.
As described in commit 2c0ac5b48a ("serial: exar: Fix stuck MSIs"),
the purpose of clearing INT0 is to prevent the PCI interrupt line from
becoming stuck asserted, "which is fatal with edge-triggered MSIs".
Like the clearing via interrupt handler that moved from common code in
commit c7e1b40590 ("tty: serial: exar: Relocate sleep wake-up
handling"), this clearing at startup can be better handled at the PCI
device level.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190801185956.3222-1-asierra@xes-inc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While commit b6b996b6cd ("treewide: Use DEVICE_ATTR_RW") converted
the rx_fifo_timeout attribute, it forgot to convert rx_fifo_trigger due
to a slightly different function naming.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20190731124555.14349-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For QUP IP versions 2.5 and above the oversampling rate is halved
from 32 to 16. Update this rate after reading hardware version
register, so that the clock divider value is correctly set to
achieve required baud rate.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Link: https://lore.kernel.org/r/20190801121153.10613-1-vivek.gautam@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When closing and shutting down the exar serial port, if the chip
has not finished sending all of the data in its buffer, the
remaining bytes will be lost. Hold off on the shutdown until the
bytes have all been sent.
Signed-off-by: Robert Middleton <robert.middleton@rm5248.com>
Link: https://lore.kernel.org/r/20190801145640.26080-1-robert.middleton@rm5248.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are Exar custom divisor support in 8250_port which belongs to
8250_exar module. Move it out to the correct module and do not contaminate
generic code with it.
Cc: Aaron Sierra <asierra@xes-inc.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190731170558.52897-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are Exar quirks in 8250_port which belong to 8250_exar module.
Extract PM routine to the correct module and do not contaminate generic code
with it.
Cc: Aaron Sierra <asierra@xes-inc.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190731170558.52897-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have a separate driver there is no need to autoconfigure ports,
we already know what they are.
Drop autoconfiguration in 8250_port and move type detection to 8250_exar.
Cc: Aaron Sierra <asierra@xes-inc.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190731170558.52897-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a driver, do not call "raw" sysfs functions, instead call driver
core ones. Specifically convert the use of sysfs_create_file() and
sysfs_remove_file() to use device_create_file() and device_remove_file()
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/20190704084617.3602-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A powerpc allyesconfig build produces this warning:
In file included from include/linux/radix-tree.h:16,
from include/linux/idr.h:15,
from include/linux/kernfs.h:13,
from include/linux/sysfs.h:16,
from include/linux/kobject.h:20,
from include/linux/device.h:16,
from include/linux/platform_device.h:13,
from drivers/tty/serial/xilinx_uartps.c:16:
drivers/tty/serial/xilinx_uartps.c: In function 'cdns_uart_console_write':
include/linux/spinlock.h:288:3: warning: 'flags' may be used uninitialized in this function [-Wmaybe-uninitialized]
_raw_spin_unlock_irqrestore(lock, flags); \
^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/tty/serial/xilinx_uartps.c:1197:16: note: 'flags' was declared here
unsigned long flags;
^~~~~
It looks like gcc just can't track the relationship between "locked"
and "flags", and it is obvious that "flags" won't be used when "locked"
is zero, so the simplest thing is to initialise flags.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20190731160557.6a09c3e1@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-45-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Last steps of .shutdown() code are identical for lpuart and lpuart32
cases, so move it all into a standalone subroutine.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-19-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By the time lpuart_shutdown() calls lpuart_stop_tx() UARTCR2_TE and
UARTCR2_TIE (which the latter will clear) are already cleared, so that
function call should effectively be a no-op. Moreso, lpuart_stop_tx()
is expected to be executed with port spinlock held, which the caller
doesn't. Given all that, drop the call to lpuart_stop_tx() in
lpuart_shutdown().
In case of lpuart32_shutdown()/lpuart32_stop_tx(), TIE won't even be
set if lpuart_dma_tx_use is true. Drop it there as well.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-18-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use cpu_relax() instead of barrier() in a tight polling loops to make
them a bit more idiomatic. Should also improve things on ARM64 a bit
since cpu_relax() will expand into "yield" instruction there.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-16-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Busy polling on a bit in a register is used in multiple places in the
driver. Move it into a shared function.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-15-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dealing with 32-bit variant of LPUART IP block appropriate I/O
helpers have to be used to properly deal with endianness
differences. Change all of the offending code to do that.
Fixes: a5fa2660d7 ("tty/serial/fsl_lpuart: Add CONSOLE_POLL support
for lpuart32.")
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-14-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clearing CSTOPB bit if it is set is functionally equivalent to jsut
clearing it unconditionally. Drop unnecessary check.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-13-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check for termios->c_cflag & CRTSCTS ensure that if we reach else
branch, CRTSCTS in termios->c_cflag is already going to be
cleard. Doing so explicitly there is not necessary. Drop it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-11-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While sharing code for Tx interrupt handler between 8 and 32 bit
variant of the peripheral saves a bit of code duplication it also adds
quite a number of lpuart_is_32() checks which makes it harder to
understand. Move shared bits back into corresponding
lpuart*_transmit_buffer functions, split lpuart_txint into
lpuart_txint and lpuart32_txint so we can drop all extra
lpuart_is_32() check and make the code flow more linear.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-10-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although I haven't observed this bug in practice, it seems that the
code for handling x_char of LPUART is pretty much identical to that of
i.MX. So the fix found in commit 7e2fb5aa8d ("serial: imx: Fix issue
in software flow control"):
serial: imx: Fix issue in software flow control
After send out x_char in UART driver, x_char needs to be cleared
by UART driver itself, otherwise data in TXFIFO can no longer be
sent out.
Also tx counter needs to be increased to keep track of correct
number of transmitted data.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
should apply here as well.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-9-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Uart_write_wakeup() will already be called as a part of
lpuart*_transmit_buffer() call, so there doesn't seem to be a reason
to call it again right after.
It also appears that second uart_write_wakeup() might potentially
cause unwanted write wakeup when transmitting an x_char. See commit
5e42e9a30c ("serial: imx: Fix x_char handling and tx flow control")
where this problem was fixed in a very similarly structured i.MX UART
driver.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-8-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears that lpuart_rxint, lpuart_txint and lpuart32_rxint were
modelled after identical function found in UART driver for
i.MX. However, while said functions are used as individual IRQ
handlers in i.MX driver (in case of i.MX1), it is not the case for
LPUART. Given that, there's no need for us to restrict the prototype
of the handler to irqreturn_t foo(int, void *) and we can drop all of
uneened boilerplate code by changing it void foo(struct lpuart_port *).
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-5-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After overruns the FIFO pointers become misaligned. This
typically shows by characters still being stuck in the FIFO
despite the empty flag being asserted. After the first
assertion of the overrun flag the empty flag still seems to
indicate FIFO state correctly and all data can be read.
However, after another overrun assertion the FIFO seems to
be off by one such that the last received character is still
in the FIFO (despite the empty flag being asserted).
Flushing the receive FIFO reinitializes pointers. Hence it
is recommended to flush the FIFO after overruns, see also:
https://community.nxp.com/thread/321175
Hence, on assertion of the overrun flag read the remaining
data from the FIFO and flush buffers.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-3-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using DMA framing error get cleared properly. However, due
to the additional read from the data register, an underflow in
the receive FIFO buffer occurs (the FIFO pointer gets out of
sync).
Clear the FIFO in case an underflow has occurred. Also disable the
receiver during this operation and when reading the data register to
minimize potential interference.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-2-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Called in only one place, for RS232, it only obscures things, as it
doesn't go well with 2 similar named functions,
imx_uart_rts_inactive() and imx_uart_rts_active(), that both are
RS485-specific.
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1564167161-3972-4-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_uart_set_mctrl() happened to set UCR2_CTSC bit whenever TIOCM_RTS
was set, no matter if RTS/CTS handshake is enabled or not. Now fixed by
turning handshake on only when CRTSCTS bit for the port is set.
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1564167161-3972-3-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't let receiver hardware automatically control RTS output if it
was requested to be inactive.
To ensure this, set_termios() shouldn't set UCR2_CTSC bit if UCR2_CTS
(=TIOCM_RTS) is cleared. Added corresponding check in imx_uart_rts_auto()
to fix this.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1564167161-3972-2-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The established way to provide PM callbacks is through struct dev_pm_ops
which is more generic.
Convert driver to use it instead of legacy approach.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190726172817.73253-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Select either pinctrl sleep state in suspend function or default state in
resume function.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Link: https://lore.kernel.org/r/1560433800-12255-4-git-send-email-erwan.leray@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_ioremap_bar may return null. This is eventually de-referenced at
drivers/dma/dw/core.c:1154 and drivers/dma/dw/core.c:1168. A null check
is needed to prevent null de-reference. I am adding the check and in
case of failure. Thanks to Andy Shevchenko for the hint on the necessity
of pci_iounmap when exiting.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20190719174848.24216-1-navid.emamdoost@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since .sg_init_one() already set sg entry page like below code.
sg_init_one()
sg_init_table(sg, 1);
sg_set_buf(sg, buf, buflen);
So it should not set sg entry page again, remove the redundant code.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20190717051930.15514-5-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use kzalloc() instead of kmalloc() to get clean rx buffer
that is useful for DMA mode debug to check the data moving
validity.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20190717051930.15514-4-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default, .of_dma_configure() init dev.coherent_dma_mask to BIT(32) that
match the eDMA address range. If re-init dev.coherent_dma_mask to zero, then
streaming dma mapping will go swiotlb dma_map, if swiotlb is not initalized
then it causes mapping failed.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20190717051930.15514-2-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array.
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190721150135.82065-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20190724131825.1875-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20190724131758.1764-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable word_count is being assigned a value that is never read before
a return, the assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20190723150314.14513-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_alloc_consistent calls dma_alloc_coherent directly.
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Link: https://lore.kernel.org/r/20190715032001.7212-1-huangfq.daxian@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For many years omap variants have been setting the runtime PM
autosuspend delay to -1 to prevent unsafe policy with lossy first
character on wake-up. The user must specifically enable the timeout
for UARTs if desired.
We must not enable the workaround for serdev devices though. It leads
into UARTs not idling if no serdev devices are loaded and there is no
sysfs entry to configure the UART in that case. And this means that
my PM may not work unless the serdev modules are loaded.
We can detect a serdev device being configured based on a dts child
node, and we can simply skip the workround in that case. And the
serdev driver can idle the port during runtime when suitable if an
out-of-band wake-up GPIO line exists for example.
Let's also add some comments to the workaround while at it.
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20190723115400.46432-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make it obvious how the gsm mux number relates to the virtual tty lines
by using helper functions instead of shifting 6 bits.
Signed-off-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/r/20190710192656.60381-3-martin@geanix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lock down TIOCSSERIAL as that can be used to change the ioport and irq
settings on a serial port. This only appears to be an issue for the serial
drivers that use the core serial code. All other drivers seem to either
ignore attempts to change port/irq or give an error.
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Matthew Garrett <mjg59@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
The SGI SN2 support is about to be removed. Remove this driver that
depends on the SN2 support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-9-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
The SGI SN2 support is about to be removed. Remove this driver that
depends on the SN2 support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-8-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
The SGI SN2 support is about to be removed. Remove this driver that
depends on the SN2 support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-7-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
The lpc32xx_loopback_set() function in hte lpc32xx_hs driver is the
one thing that relies on platform header files. Move that into the
core platform code so we only need a variable declaration for it,
and enable COMPILE_TEST building.
Link: https://lore.kernel.org/r/20190809144043.476786-12-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The only thing that prevents building this driver on other
platforms is the mach/hardware.h include, which is not actually
used here at all, so remove the line and allow CONFIG_COMPILE_TEST.
Link: https://lore.kernel.org/r/20190809144043.476786-5-arnd@arndb.de
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After commit ddde3c18b7 ("vt: More locking checks") kdb / kgdb has
become useless because my console is filled with spews of:
WARNING: CPU: 0 PID: 0 at .../drivers/tty/vt/vt.c:3846 con_is_visible+0x50/0x74
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.0-rc1+ #48
Hardware name: Rockchip (Device Tree)
Backtrace:
[<c020ce9c>] (dump_backtrace) from [<c020d188>] (show_stack+0x20/0x24)
[<c020d168>] (show_stack) from [<c0a8fc14>] (dump_stack+0xb0/0xd0)
[<c0a8fb64>] (dump_stack) from [<c0232c58>] (__warn+0xec/0x11c)
[<c0232b6c>] (__warn) from [<c0232dc4>] (warn_slowpath_null+0x4c/0x58)
[<c0232d78>] (warn_slowpath_null) from [<c06338a0>] (con_is_visible+0x50/0x74)
[<c0633850>] (con_is_visible) from [<c0634078>] (con_scroll+0x108/0x1ac)
[<c0633f70>] (con_scroll) from [<c0634160>] (lf+0x44/0x88)
[<c063411c>] (lf) from [<c06363ec>] (vt_console_print+0x1a4/0x2bc)
[<c0636248>] (vt_console_print) from [<c02f628c>] (vkdb_printf+0x420/0x8a4)
[<c02f5e6c>] (vkdb_printf) from [<c02f6754>] (kdb_printf+0x44/0x60)
[<c02f6714>] (kdb_printf) from [<c02fa6f4>] (kdb_main_loop+0xf4/0x6e0)
[<c02fa600>] (kdb_main_loop) from [<c02fd5f0>] (kdb_stub+0x268/0x398)
[<c02fd388>] (kdb_stub) from [<c02f3ba0>] (kgdb_cpu_enter+0x1f8/0x674)
[<c02f39a8>] (kgdb_cpu_enter) from [<c02f4330>] (kgdb_handle_exception+0x1c4/0x1fc)
[<c02f416c>] (kgdb_handle_exception) from [<c0210fe0>] (kgdb_compiled_brk_fn+0x30/0x3c)
[<c0210fb0>] (kgdb_compiled_brk_fn) from [<c020d7ac>] (do_undefinstr+0x180/0x1a0)
[<c020d62c>] (do_undefinstr) from [<c0201b44>] (__und_svc_finish+0x0/0x3c)
...
[<c02f3224>] (kgdb_breakpoint) from [<c02f3310>] (sysrq_handle_dbg+0x58/0x6c)
[<c02f32b8>] (sysrq_handle_dbg) from [<c062abf0>] (__handle_sysrq+0xac/0x154)
Let's disable this warning when we're in kgdb to avoid the spew. The
whole system is stopped when we're in kgdb so we can't exactly wait
for someone else to drop the lock. Presumably the best we can do is
to disable the warning and hope for the best.
Fixes: ddde3c18b7 ("vt: More locking checks")
Cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20190725183551.169208-1-dianders@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a helper to match a device by its type and provide wrappers
for {bus/class/driver}_find_device() APIs.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-usb@vger.kernel.org
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20190723221838.12024-5-suzuki.poulose@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are 2 tty/vt patches for 5.3-rc2
- delete the netx-serial driver as the arch has been removed, no need
to keep the serial driver for it around either.
- vt console_lock fix to resolve a reported noisy warning at runtime
Both of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXT2MbA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk0iACeOnBnhE1OKqIVsG11K619UtLb67sAoL9h6Rgk
3PWLkB02N1ApgevMEOs5
=V3Xf
-----END PGP SIGNATURE-----
Merge tag 'tty-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty fixes from Greg KH:
"Here are two tty/vt fixes:
- delete the netx-serial driver as the arch has been removed, no need
to keep the serial driver for it around either.
- vt console_lock fix to resolve a reported noisy warning at runtime
Both of these have been in linux-next with no reported issues"
* tag 'tty-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt: Grab console_lock around con_is_bound in show_bind
tty: serial: netx: Delete driver
Pull locking fixes from Thomas Gleixner:
"A set of locking fixes:
- Address the fallout of the rwsem rework. Missing ACQUIREs and a
sanity check to prevent a use-after-free
- Add missing checks for unitialized mutexes when mutex debugging is
enabled.
- Remove the bogus code in the generic SMP variant of
arch_futex_atomic_op_inuser()
- Fixup the #ifdeffery in lockdep to prevent compile warnings"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/mutex: Test for initialized mutex
locking/lockdep: Clean up #ifdef checks
locking/lockdep: Hide unused 'class' variable
locking/rwsem: Add ACQUIRE comments
tty/ldsem, locking/rwsem: Add missing ACQUIRE to read_failed sleep loop
lcoking/rwsem: Add missing ACQUIRE to read_slowpath sleep loop
locking/rwsem: Add missing ACQUIRE to read_slowpath exit when queue is empty
locking/rwsem: Don't call owner_on_cpu() on read-owner
futex: Cleanup generic SMP variant of arch_futex_atomic_op_inuser()
While reviewing rwsem down_slowpath, Will noticed ldsem had a copy of
a bug we just found for rwsem.
X = 0;
CPU0 CPU1
rwsem_down_read()
for (;;) {
set_current_state(TASK_UNINTERRUPTIBLE);
X = 1;
rwsem_up_write();
rwsem_mark_wake()
atomic_long_add(adjustment, &sem->count);
smp_store_release(&waiter->task, NULL);
if (!waiter.task)
break;
...
}
r = X;
Allows 'r == 0'.
Reported-by: Will Deacon <will@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 4898e640ca ("tty: Add timed, writer-prioritized rw semaphore")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Not really harmful not to, but also not harm in grabbing the lock. And
this shuts up a new WARNING I introduced in commit ddde3c18b7 ("vt:
More locking checks").
Reported-by: Jens Remus <jremus@linux.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Martin Hostettler <textshell@uchuujin.de>
Cc: Adam Borowski <kilobyte@angband.pl>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Fixes: ddde3c18b7 ("vt: More locking checks")
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: Jens Remus <jremus@linux.ibm.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/r/20190718080903.22622-1-daniel.vetter@ffwll.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Netx ARM machine was deleted from the kernel. This driver
had no users and has to go.
Cc: Robert Schwebel <r.schwebel@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20190722065146.4844-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SoC platform changes. Main theme this merge window:
- The Netx platform (Netx 100/500) platform is removed by Linus Walleij--
the SoC doesn't have active maintainers with hardware, and in
discussions with the vendor the agreement was that it's OK to remove.
- Russell King has a series of patches that cleans up and refactors
SA1101 and RiscPC support.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl0yKOgPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3SNEP/iJsMeeunX0P7Ym3zNFjykhspkkUmo7sEKuz
NBcexnQpkm+OLgjfwT7j3kXvOs4mzMzH56J6h7dEDSHbQP1MDIgpMw6OEzMMsQTV
XL1AWz1IO7Sq/mG17daPs9c75o6NYQ7pSEd/ncbjKuJQOpGsi4DyrVrhk9WdzYl2
hcs4XOzOMZgDTsXHVdWkfpHazpWxEXPCD7v5bt6ueU0YnT3csUbzOTTvw+55JxRV
fYz0lg4wTMRYMQMOejpx1HXwdmbVOHLUYkCxcLUaVqMnm88q/IddJVklBbPGWAU5
Z4gFpL+FxcFhEZtu28CoubPYzf/mHDk8Ry2UWwBiRwiGoKfblomI1fpnbyrX53aE
lpO5p7MfOVVV2WNxpbUND+ilbgKOREfRHd314GLPUjwudp2sTuDRZ1GAbt3JwsIM
L1HesyjCtb6itCSwGsmmGsX2Wvu+WT7slpsYwHs2qklE/X1zQq0R4Jf2xUNpwqPb
FqGZAtc6CCQtyF/Mcpp6OQd+cV0tgQVIw7teKol/xR1dSzN/+1zO1J9UHk9/dWUU
sb5lGa/AtBrIbWxS1qLuA5bgyDqxXYDZi0y/Bu1qMHYebRW37z9kvomtzBiMNX2o
SAxvr9iGPlTxTjGjRCyBVFmsbCMYLabNoL9tuuXvo+DnjFoOilTef+qePOv7ZYZX
kwUyS2eu
=FX6e
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC platform changes. Main theme this merge window:
- The Netx platform (Netx 100/500) platform is removed by Linus
Walleij-- the SoC doesn't have active maintainers with hardware,
and in discussions with the vendor the agreement was that it's OK
to remove.
- Russell King has a series of patches that cleans up and refactors
SA1101 and RiscPC support"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
ARM: stm32: use "depends on" instead of "if" after prompt
ARM: sa1100: convert to common clock framework
ARM: exynos: Cleanup cppcheck shifting warning
ARM: pxa/lubbock: remove lubbock_set_misc_wr() from global view
ARM: exynos: Only build MCPM support if used
arm: add missing include platform-data/atmel.h
ARM: davinci: Use GPIO lookup table for DA850 LEDs
ARM: OMAP2: drop explicit assembler architecture
ARM: use arch_extension directive instead of arch argument
ARM: imx: Switch imx7d to imx-cpufreq-dt for speed-grading
ARM: bcm: Enable PINCTRL for ARCH_BRCMSTB
ARM: bcm: Enable ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB
ARM: riscpc: enable chained scatterlist support
ARM: riscpc: reduce IRQ handling code
ARM: riscpc: move RiscPC assembly files from arch/arm/lib to mach-rpc
ARM: riscpc: parse video information from tagged list
ARM: riscpc: add ecard quirk for Atomwide 3port serial card
MAINTAINERS: mvebu: Add git entry
soc: ti: pm33xx: Add a print while entering RTC only mode with DDR in self-refresh
ARM: OMAP2+: Make some variables static
...
In the sysctl code the proc_dointvec_minmax() function is often used to
validate the user supplied value between an allowed range. This
function uses the extra1 and extra2 members from struct ctl_table as
minimum and maximum allowed value.
On sysctl handler declaration, in every source file there are some
readonly variables containing just an integer which address is assigned
to the extra1 and extra2 members, so the sysctl range is enforced.
The special values 0, 1 and INT_MAX are very often used as range
boundary, leading duplication of variables like zero=0, one=1,
int_max=INT_MAX in different source files:
$ git grep -E '\.extra[12].*&(zero|one|int_max)' |wc -l
248
Add a const int array containing the most commonly used values, some
macros to refer more easily to the correct array member, and use them
instead of creating a local one for every object file.
This is the bloat-o-meter output comparing the old and new binary
compiled with the default Fedora config:
# scripts/bloat-o-meter -d vmlinux.o.old vmlinux.o
add/remove: 2/2 grow/shrink: 0/2 up/down: 24/-188 (-164)
Data old new delta
sysctl_vals - 12 +12
__kstrtab_sysctl_vals - 12 +12
max 14 10 -4
int_max 16 - -16
one 68 - -68
zero 128 28 -100
Total: Before=20583249, After=20583085, chg -0.00%
[mcroce@redhat.com: tipc: remove two unused variables]
Link: http://lkml.kernel.org/r/20190530091952.4108-1-mcroce@redhat.com
[akpm@linux-foundation.org: fix net/ipv6/sysctl_net_ipv6.c]
[arnd@arndb.de: proc/sysctl: make firmware loader table conditional]
Link: http://lkml.kernel.org/r/20190617130014.1713870-1-arnd@arndb.de
[akpm@linux-foundation.org: fix fs/eventpoll.c]
Link: http://lkml.kernel.org/r/20190430180111.10688-1-mcroce@redhat.com
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert docs to ReST and add them to the arch-specific
book.
The conversion here was trivial, as almost every file there
was already using an elegant format close to ReST standard.
The changes were mostly to mark literal blocks and add a few
missing section title identifiers.
One note with regards to "--": on Sphinx, this can't be used
to identify a list, as it will format it badly. This can be
used, however, to identify a long hyphen - and "---" is an
even longer one.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> # cxl
* 'for-arm-soc' of git://git.armlinux.org.uk/~rmk/linux-arm: (21 commits)
ARM: sa1100: convert to common clock framework
ARM: riscpc: enable chained scatterlist support
ARM: riscpc: reduce IRQ handling code
ARM: riscpc: move RiscPC assembly files from arch/arm/lib to mach-rpc
ARM: riscpc: parse video information from tagged list
ARM: riscpc: add ecard quirk for Atomwide 3port serial card
ARM: sa1100/neponset: convert serial to use gpiod APIs
ARM: sa1100/hackkit: remove empty serial mctrl functions
ARM: sa1100/badge4: remove commented out modem control initialisers
ARM: sa1100/h3xxx: convert serial to gpiod APIs
ARM: sa1100/assabet: convert serial to gpiod APIs
serial: sa1100: add note about modem control signals
serial: sa1100: add support for mctrl gpios
ARM: riscpc: dma: use __iomem pointers for writing DMA
ARM: riscpc: dma: improve address/length writing
ARM: riscpc: dma: make state a local variable
ARM: riscpc: dma: eliminate "cur_sg" scatterlist usage
ARM: riscpc: fix DMA
ARM: riscpc: fix ecard printing
ARM: riscpc: fix lack of keyboard interrupts after irq conversion
...
Signed-off-by: Olof Johansson <olof@lixom.net>
There are lots of documents under Documentation/*.txt and a few other
orphan documents elsehwere that belong to the driver-API book.
Move them to their right place.
Reviewed-by: Cornelia Huck <cohuck@redhat.com> # vfio-related parts
Acked-by: Logan Gunthorpe <logang@deltatee.com> # switchtec
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Converts ARM the text files to ReST, preparing them to be an
architecture book.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by Corentin Labbe <clabbe.montjoie@gmail.com> # For sun4i-ss
Convert this small file to ReST in preparation for adding it to
the driver-api book.
While this is not part of the driver-api book, mark it as
:orphan:, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Notable changes:
- Removal of the NPU DMA code, used by the out-of-tree Nvidia driver, as well
as some other functions only used by drivers that haven't (yet?) made it
upstream.
- A fix for a bug in our handling of hardware watchpoints (eg. perf record -e
mem: ...) which could lead to register corruption and kernel crashes.
- Enable HAVE_ARCH_HUGE_VMAP, which allows us to use large pages for vmalloc
when using the Radix MMU.
- A large but incremental rewrite of our exception handling code to use gas
macros rather than multiple levels of nested CPP macros.
And the usual small fixes, cleanups and improvements.
Thanks to:
Alastair D'Silva, Alexey Kardashevskiy, Andreas Schwab, Aneesh Kumar K.V, Anju
T Sudhakar, Anton Blanchard, Arnd Bergmann, Athira Rajeev, Cédric Le Goater,
Christian Lamparter, Christophe Leroy, Christophe Lombard, Christoph Hellwig,
Daniel Axtens, Denis Efremov, Enrico Weigelt, Frederic Barrat, Gautham R.
Shenoy, Geert Uytterhoeven, Geliang Tang, Gen Zhang, Greg Kroah-Hartman, Greg
Kurz, Gustavo Romero, Krzysztof Kozlowski, Madhavan Srinivasan, Masahiro
Yamada, Mathieu Malaterre, Michael Neuling, Nathan Lynch, Naveen N. Rao,
Nicholas Piggin, Nishad Kamdar, Oliver O'Halloran, Qian Cai, Ravi Bangoria,
Sachin Sant, Sam Bobroff, Satheesh Rajendran, Segher Boessenkool, Shaokun
Zhang, Shawn Anastasio, Stewart Smith, Suraj Jitindar Singh, Thiago Jung
Bauermann, YueHaibing.
-----BEGIN PGP SIGNATURE-----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=3dBZ
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Removal of the NPU DMA code, used by the out-of-tree Nvidia driver,
as well as some other functions only used by drivers that haven't
(yet?) made it upstream.
- A fix for a bug in our handling of hardware watchpoints (eg. perf
record -e mem: ...) which could lead to register corruption and
kernel crashes.
- Enable HAVE_ARCH_HUGE_VMAP, which allows us to use large pages for
vmalloc when using the Radix MMU.
- A large but incremental rewrite of our exception handling code to
use gas macros rather than multiple levels of nested CPP macros.
And the usual small fixes, cleanups and improvements.
Thanks to: Alastair D'Silva, Alexey Kardashevskiy, Andreas Schwab,
Aneesh Kumar K.V, Anju T Sudhakar, Anton Blanchard, Arnd Bergmann,
Athira Rajeev, Cédric Le Goater, Christian Lamparter, Christophe
Leroy, Christophe Lombard, Christoph Hellwig, Daniel Axtens, Denis
Efremov, Enrico Weigelt, Frederic Barrat, Gautham R. Shenoy, Geert
Uytterhoeven, Geliang Tang, Gen Zhang, Greg Kroah-Hartman, Greg Kurz,
Gustavo Romero, Krzysztof Kozlowski, Madhavan Srinivasan, Masahiro
Yamada, Mathieu Malaterre, Michael Neuling, Nathan Lynch, Naveen N.
Rao, Nicholas Piggin, Nishad Kamdar, Oliver O'Halloran, Qian Cai, Ravi
Bangoria, Sachin Sant, Sam Bobroff, Satheesh Rajendran, Segher
Boessenkool, Shaokun Zhang, Shawn Anastasio, Stewart Smith, Suraj
Jitindar Singh, Thiago Jung Bauermann, YueHaibing"
* tag 'powerpc-5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (163 commits)
powerpc/powernv/idle: Fix restore of SPRN_LDBAR for POWER9 stop state.
powerpc/eeh: Handle hugepages in ioremap space
ocxl: Update for AFU descriptor template version 1.1
powerpc/boot: pass CONFIG options in a simpler and more robust way
powerpc/boot: add {get, put}_unaligned_be32 to xz_config.h
powerpc/irq: Don't WARN continuously in arch_local_irq_restore()
powerpc/module64: Use symbolic instructions names.
powerpc/module32: Use symbolic instructions names.
powerpc: Move PPC_HA() PPC_HI() and PPC_LO() to ppc-opcode.h
powerpc/module64: Fix comment in R_PPC64_ENTRY handling
powerpc/boot: Add lzo support for uImage
powerpc/boot: Add lzma support for uImage
powerpc/boot: don't force gzipped uImage
powerpc/8xx: Add microcode patch to move SMC parameter RAM.
powerpc/8xx: Use IO accessors in microcode programming.
powerpc/8xx: replace #ifdefs by IS_ENABLED() in microcode.c
powerpc/8xx: refactor programming of microcode CPM params.
powerpc/8xx: refactor printing of microcode patch name.
powerpc/8xx: Refactor microcode write
powerpc/8xx: refactor writing of CPM microcode arrays
...
Pull sparc updates from David Miller:
"Just a few small changes:
- Fix console naming inconsistency with hypervisor consoles, from
John Paul Adrian Glaubitz
- Fix userland compilation due to use of u_int, from Masahiro Yamada"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Add missing newline at end of file
sparc: fix unknown type name u_int in uapi header
sparc: configs: Remove useless UEVENT_HELPER_PATH
sparc: Remove redundant copy of the LGPL-2.0
sunhv: Fix device naming inconsistency between sunhv_console and sunhv_reg
Here is the "large" TTY and Serial driver update for 5.3-rc1.
It's in the negative number of lines overall as we removed an obsolete
serial driver that was causing problems for some people who were trying
to clean up some apis (the mpsc.c driver, which only worked for some
pre-production hardware that no one has anymore.)
Other than that, lots of tiny changes, cleaning up small things along
with some platform-specific serial driver updates.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSXkOA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynidwCgoCX5L3zayZ7pZTWmtLsTOy0O0WYAn1gzleNg
sSRApC0DGfxOIrco7urV
=0KJa
-----END PGP SIGNATURE-----
Merge tag 'tty-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the "large" TTY and Serial driver update for 5.3-rc1.
It's in the negative number of lines overall as we removed an obsolete
serial driver that was causing problems for some people who were
trying to clean up some apis (the mpsc.c driver, which only worked for
some pre-production hardware that no one has anymore.)
Other than that, lots of tiny changes, cleaning up small things along
with some platform-specific serial driver updates.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'tty-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (68 commits)
tty: serial: fsl_lpuart: add imx8qxp support
serial: imx: set_termios(): preserve RTS state
serial: imx: set_termios(): clarify RTS/CTS bits calculation
serial: imx: set_termios(): factor-out 'ucr2' initial value
serial: sh-sci: Terminate TX DMA during buffer flushing
serial: sh-sci: Fix TX DMA buffer flushing and workqueue races
serial: mpsc: Remove obsolete MPSC driver
serial: 8250: 8250_core: Fix missing unlock on error in serial8250_register_8250_port()
serial: stm32: add RX and TX FIFO flush
serial: stm32: add support of RX FIFO threshold
serial: stm32: add support of TX FIFO threshold
serial: stm32: update PIO transmission
serial: stm32: add support of timeout interrupt for RX
Revert "serial: 8250: Don't service RX FIFO if interrupts are disabled"
tty/serial/8250: use mctrl_gpio helpers
serial: mctrl_gpio: Check if GPIO property exisits before requesting it
serial: 8250: pericom_do_set_divisor can be static
tty: serial_core: Set port active bit in uart_port_activate
serial: 8250: Add MSR/MCR TIOCM conversion wrapper functions
serial: 8250: factor out serial8250_{set,clear}_THRI() helpers
...
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
- remove fbdev notifier usage for fbcon (as prep work to clean up the fbcon
locking), add locking checks in vt/console code and make assorted cleanups
in fbdev and backlight code (Daniel Vetter)
- add COMPILE_TEST support to atmel_lcdfb, da8xx-fb, gbefb, imxfb, pvr2fb and
pxa168fb drivers (me)
- fix DMA API abuse in au1200fb and jz4740_fb drivers (Christoph Hellwig)
- add check for new BGRT status field rotation bits in efifb driver (Hans de
Goede)
- mark expected switch fall-throughs in s3c-fb driver (Gustavo A. R. Silva)
- remove fbdev mxsfb driver in favour of the drm version (Fabio Estevam)
- remove broken rfbi code from omap2fb driver (me)
- misc fixes (Arnd Bergmann, Shobhit Kukreti, Wei Yongjun, me)
- misc cleanups (Gustavo A. R. Silva, Colin Ian King, me)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=W1AD
-----END PGP SIGNATURE-----
Merge tag 'fbdev-v5.3' of git://github.com/bzolnier/linux
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
- remove fbdev notifier usage for fbcon (as prep work to clean up the
fbcon locking), add locking checks in vt/console code and make
assorted cleanups in fbdev and backlight code (Daniel Vetter)
- add COMPILE_TEST support to atmel_lcdfb, da8xx-fb, gbefb, imxfb,
pvr2fb and pxa168fb drivers (me)
- fix DMA API abuse in au1200fb and jz4740_fb drivers (Christoph
Hellwig)
- add check for new BGRT status field rotation bits in efifb driver
(Hans de Goede)
- mark expected switch fall-throughs in s3c-fb driver (Gustavo A. R.
Silva)
- remove fbdev mxsfb driver in favour of the drm version (Fabio
Estevam)
- remove broken rfbi code from omap2fb driver (me)
- misc fixes (Arnd Bergmann, Shobhit Kukreti, Wei Yongjun, me)
- misc cleanups (Gustavo A. R. Silva, Colin Ian King, me)
* tag 'fbdev-v5.3' of git://github.com/bzolnier/linux: (62 commits)
video: fbdev: imxfb: fix a typo in imxfb_probe()
video: fbdev: s3c-fb: Mark expected switch fall-throughs
video: fbdev: s3c-fb: fix sparse warnings about using incorrect types
video: fbdev: don't print error message on framebuffer_alloc() failure
video: fbdev: intelfb: return -ENOMEM on framebuffer_alloc() failure
video: fbdev: s3c-fb: return -ENOMEM on framebuffer_alloc() failure
vga_switcheroo: Depend upon fbcon being built-in, if enabled
video: fbdev: omap2: remove rfbi
video: fbdev: atmel_lcdfb: remove redundant initialization to variable ret
video: fbdev-MMP: Use struct_size() in devm_kzalloc()
video: fbdev: controlfb: fix warnings about comparing pointer to 0
efifb: BGRT: Add check for new BGRT status field rotation bits
jz4740_fb: fix DMA API abuse
video: fbdev: pvr2fb: fix link error for pvr2fb_pci_exit
video: fbdev: s3c-fb: add COMPILE_TEST support
video: fbdev: imxfb: fix sparse warnings about using incorrect types
video: fbdev: pvr2fb: fix build warning when compiling as module
fbcon: Export fbcon_update_vcs
backlight: simplify lcd notifier
staging/olpc_dcon: Add drm conversion to TODO
...
The lpuart of imx8ulp is basically the same as imx7ulp, but it
has new feature support based on imx7ulp, like it can assert a
DMA request on EOP(end-of-packet). imx8ulp lpuart use two clocks,
one is ipg bus clock that is used to access registers, the other
is baud clock that is used to transmit-receive data.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20190704134007.2316-1-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid repeating the same code for rs485 twice.
Make it obvious we clear CRTSCTS bit in termios->c_cflag whenever
sport->have_rtscts is false.
Make it obvious we clear UCR2_IRTS whenever CRTSCTS is set.
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1561558293-7683-4-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set common bits in a separate statement to make initialization
explicit and not repeat the common part.
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Reviewed-by: Uwe Kleine-Knig <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/1561558293-7683-3-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the .flush_buffer() callback clears sci_port.tx_dma_len since
commit 1cf4a7efdc ("serial: sh-sci: Fix race condition causing
garbage during shutdown"), it does not terminate a transmit DMA
operation that may be in progress.
Fix this by terminating any pending DMA operations, and resetting the
corresponding cookie.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Link: https://lore.kernel.org/r/20190624123540.20629-3-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When uart_flush_buffer() is called, the .flush_buffer() callback zeroes
the tx_dma_len field. This may race with the work queue function
handling transmit DMA requests:
1. If the buffer is flushed before the first DMA API call,
dmaengine_prep_slave_single() may be called with a zero length,
causing the DMA request to never complete, leading to messages
like:
rcar-dmac e7300000.dma-controller: Channel Address Error happen
and, with debug enabled:
sh-sci e6e88000.serial: sci_dma_tx_work_fn: ffff800639b55000: 0...0, cookie 126
and DMA timeouts.
2. If the buffer is flushed after the first DMA API call, but before
the second, dma_sync_single_for_device() may be called with a zero
length, causing the transmit data not to be flushed to RAM, and
leading to stale data being output.
Fix this by:
1. Letting sci_dma_tx_work_fn() return immediately if the transmit
buffer is empty,
2. Extending the critical section to cover all DMA preparational work,
so tx_dma_len stays consistent for all of it,
3. Using local copies of circ_buf.head and circ_buf.tail, to make sure
they match the actual operation above.
Reported-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Suggested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Link: https://lore.kernel.org/r/20190624123540.20629-2-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for the Marvell MV64x60 line of bridge chips that contained
MPSC controllers has been removed and there are no other components
that have that controller so remove its driver.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Link: https://lore.kernel.org/r/20190626160553.28518-1-mgreer@animalcreek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing unlock before return from function serial8250_register_8250_port()
in the error handling case.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20190703055908.141294-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds a flush of RX and TX FIFOs, and fixes some errors:
- adds RX FIFO flush in startup fonction
- removes the useless transmitter enabling in startup fonction
(e.g. receiver only, see Documentation/serial/driver)
- configures FIFO threshold before enabling it, rather than after
- flushes both TX and RX in set_termios function
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds the support of RX FIFO threshold in order to improve the RX FIFO
management.
This is done by enabling fifo threshold interrupt, instead of relying
on rx empty/fifo not full irq. That basically generates one irq/char
currently. With this patch:
- RXCFG is set to half fifo size (e.g. 16/2 = 8 data for a 16 data depth
FIFO)
- irq rate may be reduced by up to 1/RXCFG, e.g. 1 over 8 with current
RXCFG setting.
- Receiver timeout is used to gather chars when FIFO threshold isn't
reached.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds the support of TX FIFO threshold in order to improve the TX FIFO
management:
- TX FIFO threshold irq enabling (instead of relying on tx empty / fifo
not full irq that generates one irq/char)
- TXCFG is set to half fifo size (e.g. 16/2 = 8 data for a 16 data depth
FIFO)
- irq rate may be reduced by up to 1/TXCFG, e.g. 1 over 8 with current
TXCFG setting.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improves PIO transmission:
- Replaces the FIFO filling per character by a filling per blocks of
characters, which provides better performances
- Replaces the active waiting loop by TX empty interrupt dynamic handling.
TXE interrupt is now enabled when data has to be sent (ie when
uart_circ is not empty), and inhibited when there is no more data to
send (ie when uart_circ is empty).
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support of RX timeout interrupts to limit the number of interrupts.
RX timeout is a number of bits (baud clock cycles) without
transmission seen in the receiver. One character is used as an arbitrary
RX timeout value.
If parity is enabled, the number of bits has to include parity bit.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2e9fe53910.
Reading LSR unconditionally but processing the error flags only if
UART_IIR_RDI bit was set before in IIR may lead to a loss of transmission
error information on UARTs where the transmission error flags are cleared
by a read of LSR. Information are lost in case an error is detected right
before the read of LSR while processing e.g. an UART_IIR_THRI interrupt.
Signed-off-by: Oliver Barta <o.barta89@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: 2e9fe53910 ("serial: 8250: Don't service RX FIFO if interrupts are disabled")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch permits the usage for GPIOs to control
the CTS/RTS/DTR/DSR/DCD/RI signals.
Changed by Stefan:
Only call mctrl_gpio_init(), if the device has no ACPI companion device
to not break existing ACPI based systems. Also only use the mctrl_gpio_
functions when "gpios" is available.
Use MSR / MCR <-> TIOCM wrapper functions.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a check for the GPIOs property existence, before the
GPIO is requested. This fixes an issue seen when the 8250 mctrl_gpio
support is added (2nd patch in this patch series) on x86 platforms using
ACPI.
Here Mika's comments from 2016-08-09:
"
I noticed that with v4.8-rc1 serial console of some of our Broxton
systems does not work properly anymore. I'm able to see output but input
does not work.
I bisected it down to commit 4ef03d3287
("tty/serial/8250: use mctrl_gpio helpers").
The reason why it fails is that in ACPI we do not have names for GPIOs
(except when _DSD is used) so we use the "idx" to index into _CRS GPIO
resources. Now mctrl_gpio_init_noauto() goes through a list of GPIOs
calling devm_gpiod_get_index_optional() passing "idx" of 0 for each. The
UART device in Broxton has following (simplified) ACPI description:
Device (URT4)
{
...
Name (_CRS, ResourceTemplate () {
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO0", 0x00, ResourceConsumer)
{
0x003A
}
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO0", 0x00, ResourceConsumer)
{
0x003D
}
})
In this case it finds the first GPIO (0x003A which happens to be RX pin
for that UART), turns it into GPIO which then breaks input for the UART
device. This also breaks systems with bluetooth connected to UART (those
typically have some GPIOs in their _CRS).
Any ideas how to fix this?
We cannot just drop the _CRS index lookup fallback because that would
break many existing machines out there so maybe we can limit this to
only DT enabled machines. Or alternatively probe if the property first
exists before trying to acquire the GPIOs (using
device_property_present()).
"
This patch implements the fix suggested by Mika in his statement above.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bug was introduced by commit b3b5764618 ("tty: serial_core: convert
uart_open to use tty_port_open"). It caused a constant warning printed
into the system log regarding the tty and port counter mismatch:
[ 21.644197] ttyS ttySx: tty_port_close_start: tty->count = 1 port count = 2
in case if session hangup was detected so the warning is printed starting
from the second open-close iteration.
Particularly the problem was discovered in situation when there is a
serial tty device without hardware back-end being setup. It is considered
by the tty-serial subsystems as a hardware problem with session hang up.
In this case uart_startup() will return a positive value with TTY_IO_ERROR
flag set in corresponding tty_struct instance. The same value will get
passed to be returned from the activate() callback and then being returned
from tty_port_open(). But since in this case tty_port_block_til_ready()
isn't called the TTY_PORT_ACTIVE flag isn't set (while the method had been
called before tty_port_open conversion was introduced and the rest of the
subsystem code expected the bit being set in this case), which prevents the
uart_hangup() method to perform any cleanups including the tty port
counter setting to zero. So the next attempt to open/close the tty device
will discover the counters mismatch.
In order to fix the problem we need to manually set the TTY_PORT_ACTIVE
flag in case if uart_startup() returned a positive value. In this case
the hang up procedure will perform a full set of cleanup actions including
the port ref-counter resetting.
Fixes: b3b5764618 "tty: serial_core: convert uart_open to use tty_port_open"
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds wrapper functions to convert MSR <-> TIOCM and also
MCR <-> TIOCM. These functions are used now in serial8250_do_set_mctrl()
and serial8250_do_get_mctrl().
Signed-off-by: Stefan Roese <sr@denx.de>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factor out similar code pieces that set or clear UART_IER_THRI bit to
serial8250_{set,clear}_THRI() helpers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to add an out-of-memory error message inside
the driver because the core MM code will take care of it.
Remove the unneeded OOM error message.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
