FIMC LITE SYSMMU devices are defined in exynos5250.dtsi, but clocks for
them are not instantiated by Exynos5250 clock provider driver. Add needed
definitions for those clocks to fix IOMMU probe failure:
ERROR: could not get clock /soc/sysmmu@13c40000:sysmmu(0)
exynos-sysmmu 13c40000.sysmmu: Failed to get device clock(s)!
exynos-sysmmu: probe of 13c40000.sysmmu failed with error -38
ERROR: could not get clock /soc/sysmmu@13c50000:sysmmu(0)
exynos-sysmmu 13c50000.sysmmu: Failed to get device clock(s)!
exynos-sysmmu: probe of 13c50000.sysmmu failed with error -38
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: bfed1074f2 ("clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks")
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Adding these EPLL output frequency entries allows to support all required
audio sample rates on the CODEC and the HDMI interface on Peach-Pit
Chromebook.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This allows changing the EPLL output frequency through the audio subsystem
clock tree leaf clocks. This change is needed to support audio on the HDMI
interface on Peach-Pi(t) Chromebook.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Clocks related to DISP1 block require special handling for power domain
turn on/off sequences. Till now this was handled by Exynos power domain
driver, but that approach was limited only to some special cases. This
patch moves handling of those operations to clock controller driver.
This gives more flexibility and allows fine tune values of some
clock-specific registers. This patch moves handling of those mentioned
clocks to Exynos5 sub-CMU driver instantiated from Exynos5250 driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Clocks related to DISP, GSC and MFC blocks require special handling for
power domain turn on/off sequences. Till now this was handled by Exynos
power domain driver, but that approach was limited only to some special
cases. This patch moves handling of those operations to clock controller
driver. This gives more flexibility and allows fine tune values of some
clock-specific registers. This patch moves handling of those mentioned
clocks to Exynos5 sub-CMU driver instantiated from Exynos5420 driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Exynos5250/5420/5800 have only one clock controller, but some of their
clock depends on respective power domains. Handling integration of clock
controller and power domain can be done using runtime PM feature of CCF
framework. This however needs a separate struct device for each power
domain. This patch adds such separate driver for a group of such clocks,
which can be instantiated more than once, each time for a different
power domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. To avoid possible mistakes we can use compile
time validation.
The patch introduces such validators and expands all initializers
with additional input frequency parameter, required to validate rates.
Since S3C24xx PLLs requires different validators two new macros have
been introduced to deal with it. Also, since PLLs 4502 and 4508 have
different formulas PLL_45XX_RATE has been replaced with PLL_4508_RATE.
As the patch adds only compile time validators it should not have impact
on compiled code.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
In this patch an erroneous P value for 74176002 output frequency is also
corrected.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Add one more entry to the exynos5433_aud_pll_rates table, this allows
to support audio sample rates: 48000, 96000, 192000 Hz with minimum
error. The M, P, S, K values re confirmed by the HW team.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
The sclk_ioclk_i2s1_bclk clock is not currently handled by any driver
and disabling this clock by the clk core prevents proper operation
of the I2S1 block. CLK_IGNORE_UNUSED flag is added as a temporary fix.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
There is a error message within devm_ioremap_resource already,
so remove the dev_err call to avoid redundant error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
There is a error message within devm_ioremap_resource already,
so remove the dev_err call to avoid redundant error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch just removes the unneeded enumeration for PLL index.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
large change that introduces runtime PM support to the clk framework. Now we
properly call runtime PM operations on the device providing a clk when the clk
is in use. This helps on SoCs where the clks provided by a device need
something to be powered on before using the clks, like power domains or
regulators. It also helps power those things down when clks aren't in use. The
other core change is a devm API addition for clk providers so we can get rid of
a bunch of clk driver remove functions that are just doing
of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and smattering
of non-critical fixes to existing drivers. The biggest diff is support for
Mediatek MT2712 and MT7622 SoCs, but those patches really just add a bunch
of data.
By the way, we're trying something new here where we build the tree up with
topic branches. We plan to work this into our workflow so that we don't step
on each other's toes, and so the fixes branch can be merged on an as-needed
basis.
Core:
- Runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- Runtime PM support for Samsung exynos5433/exynos4412 providers
- Removal of clkdev aliases on Samsung SoCs
- Convert clk-gpio to use gpio descriptors
- Various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- Sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- Support for the second display unit clock on Renesas RZ/G1E
- Suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- New clock ids for Rockchip rk3188 and rk3368 SoCs
- Various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hC7z
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have two changes to the core framework this time around.
The first being a large change that introduces runtime PM support to
the clk framework. Now we properly call runtime PM operations on the
device providing a clk when the clk is in use. This helps on SoCs
where the clks provided by a device need something to be powered on
before using the clks, like power domains or regulators. It also helps
power those things down when clks aren't in use.
The other core change is a devm API addition for clk providers so we
can get rid of a bunch of clk driver remove functions that are just
doing of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and
smattering of non-critical fixes to existing drivers. The biggest diff
is support for Mediatek MT2712 and MT7622 SoCs, but those patches
really just add a bunch of data.
By the way, we're trying something new here where we build the tree up
with topic branches. We plan to work this into our workflow so that we
don't step on each other's toes, and so the fixes branch can be merged
on an as-needed basis.
Summary:
Core:
- runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- runtime PM support for Samsung exynos5433/exynos4412 providers
- removal of clkdev aliases on Samsung SoCs
- convert clk-gpio to use gpio descriptors
- various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- support for the second display unit clock on Renesas RZ/G1E
- suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- new clock ids for Rockchip rk3188 and rk3368 SoCs
- various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: stm32h7: fix test of clock config
clk: pxa: fix building on older compilers
clk: sunxi-ng: a83t: Fix i2c buses bits
clk: ti: dra7-atl-clock: fix child-node lookups
clk: qcom: common: fix legacy board-clock registration
clk: uniphier: fix DAPLL2 clock rate of Pro5
clk: uniphier: fix parent of miodmac clock data
clk: hi3798cv200: correct parent mux clock for 'clk_sdio0_ciu'
clk: hisilicon: Delete an error message for a failed memory allocation in hisi_register_clkgate_sep()
clk: hi3660: fix incorrect uart3 clock freqency
clk: kona-setup: Delete error messages for failed memory allocations
ARC: clk: fix spelling mistake: "configurarion" -> "configuration"
clk: cdce925: remove redundant check for non-null parent_name
clk: versatile: Improve sizeof() usage
clk: versatile: Delete error messages for failed memory allocations
clk: ux500: Improve sizeof() usage
clk: ux500: Delete error messages for failed memory allocations
clk: spear: Delete error messages for failed memory allocations
clk: ti: Delete error messages for failed memory allocations
clk: mmp: Adjust checks for NULL pointers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- An addition of separate driver for the Exynos 4412 ISP CMU, needed
to model and properly handle the clock controller's dependencies
on the ISP power domain.
- Adding __maybe_unused attributes to the exynos5433_cmu_{suspend,
resume} ops to suppress compiler warnings with CONFIG_PM disabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DlbQ
-----END PGP SIGNATURE-----
Merge tag 'clk-v4.15-exynos-pm' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk into clk-next
Pull Samsung clk driver updates from Sylwester Nawrocki:
- An addition of separate driver for the Exynos 4412 ISP CMU, needed
to model and properly handle the clock controller's dependencies
on the ISP power domain.
- Adding __maybe_unused attributes to the exynos5433_cmu_{suspend,
resume} ops to suppress compiler warnings with CONFIG_PM disabled.
* tag 'clk-v4.15-exynos-pm' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk:
clk: samsung: Add a separate driver for Exynos4412 ISP clocks
clk: samsung: Add dt bindings for Exynos4412 ISP clock controller
clk: samsung: Instantiate Exynos4412 ISP clocks only when available
clk: samsung: exynos5433: mark PM functions as __maybe_unused
Overall clk/samsung clean up and fixes. Removed remaining unused code
after removal of exynos4212 SoC support; dropped internal data structure
fields and related code for registering clkdev lookup entry for each
possible clock object, clkdev aliases could still be defined if needed
in a separate table; other minor fixes of the clock tree definitions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VHBX
-----END PGP SIGNATURE-----
Merge tag 'clk-v4.15-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk into clk-next
Pull Samsung clk driver updates from Sylwester Nawrocki:
Overall clk/samsung clean up and fixes. Removed remaining unused code
after removal of exynos4212 SoC support; dropped internal data structure
fields and related code for registering clkdev lookup entry for each
possible clock object, clkdev aliases could still be defined if needed
in a separate table; other minor fixes of the clock tree definitions.
* tag 'clk-v4.15-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk:
clk: samsung: Remove obsolete clkdev alias support
clk: samsung: Add explicit MPLL, EPLL clkdev aliases in S3C2443 driver
clk: samsung: Rework clkdev alias handling in S3C2443 driver
clk: samsung: Rework clkdev alias handling in Exynos5440 driver
clk: samsung: Drop useless alias in Exynos5420 clk driver
clk: samsung: Remove clkdev alias support in Exynos5250 clk driver
clk: samsung: Remove double assignment of CLK_ARM_CLK in Exynos4 driver
clk: samsung: Remove clkdev alias support in Exynos4 clk driver
clk: samsung: Remove support for obsolete Exynos4212 CPU clock
clk: samsung: Remove support for Exynos4212 SoCs in Exynos CLKOUT driver
clk: samsung: Properly propagate flags in __PLL macro
clk: samsung: Fix m2m scaler clock on Exynos542x
clk: samsung: Delete a memory allocation error message in clk-cpu.c
Some registers for the Exynos 4412 ISP (Camera subsystem) clocks are
located in the ISP power domain. Because those registers are also
located in a different memory region than the main clock controller,
support for them can be provided by a separate clock controller.
This in turn allows to almost seamlessly make it aware of the power
domain using recently introduced runtime PM support for clocks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Some registers for the Exynos 4412 ISP (Camera subsystem) clocks are
located in the ISP power domain. Instantiate those clocks only when
provided clock registers resource covers those registers. This is
a preparation for adding a separate clock driver for ISP clocks,
which will be integrated with power domain using runtime PM feature.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The suspend/resume functions are referenced conditionally, causing
a harmless warning when CONFIG_PM is disabled:
drivers/clk/samsung/clk-exynos5433.c:5476:12: error: 'exynos5433_cmu_resume' defined but not used [-Werror=unused-function]
drivers/clk/samsung/clk-exynos5433.c:5453:12: error: 'exynos5433_cmu_suspend' defined but not used [-Werror=unused-function]
This marks both as __maybe_unused to shut up the warning.
Fixes: 523d3de41f ("clk: samsung: exynos5433: Add support for runtime PM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Remove support for obsolete clkdev alias definition in generic helper
macros for MUX, DIV, GATE and PLL clocks. clkdev aliases can be still
created using samsung_clk_register_alias() function if given platform
still needs them. All current drivers have been converted not to use
*_A-style macros and checked if there are any clients for the PLL
clocks, which had aliases created unconditionally.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
S3C2443 platform still use non-dt based lookup in some of its drivers
to get MPLL and EPLL clocks. Till now it worked only because PLL()
macro implicitly created aliases for all instantiated clocks. This
feature will be removed, so explicitly create aliases for MPLL and
EPLL clocks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
S3C2443 SoC still uses old, non-dt CPUfreq driver, which requires clkdev
aliases to get access to proper clocks. Create those aliases using
samsung_clk_register_alias() function instead of using *_A clock macros,
which will be removed soon.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Exynos5440 still uses old, non-dt CPUfreq driver, which requires clkdev
aliases to get access to proper clocks. Create those aliases using
samsung_clk_register_alias() function instead of using *_A clock macros,
which will be removed soon.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Drop clkdev alias for "mout_aclk400_mscl" clock. It was not used at all
and it was probably committed by accident.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
All Exynos5250 boards have been fully converted to device-tree and use
generic dt-based CPUfreq driver, so there is no need to create any clkdev
aliases for the clocks. Drop all the code related to aliases handling.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
CLK_ARM_CLK ("armclk") clock is provided by cpu-clk subdriver, which is
instantiated after creating all divider clocks from exynos4_div_clks
array. There is no point assigning this id to "div_core2" clock and later
overwrite with proper "armcpu" clock by cpu-clk subdriver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
All Exynos4 boards have been fully converted to device-tree and use generic
dt-based CPUfreq driver, so there is no need to create any clkdev aliases
for the clocks. Drop all the code related to aliases handling.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Support for Exynos 4212 SoC has been removed by commit bca9085e0a ("ARM:
dts: exynos: remove Exynos4212 support (dead code)"), so there is no need
to keep dead code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Support for Exynos4212 SoCs has been removed by commit bca9085e0a ("ARM:
dts: exynos: remove Exynos4212 support (dead code)"), so there is no need
to keep remaining dead code related to this SoC version.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Commit 6edfa11cb3 ("clk: samsung: Add enable/disable operation for
PLL36XX clocks") added enable/disable operations to PLL clocks. Prior that
VPLL and EPPL clocks were always enabled because the enable bit was never
touched. Those clocks have to be enabled during suspend/resume cycle,
because otherwise board fails to enter sleep mode. This patch enables them
unconditionally before entering system suspend state. System restore
function will set them to the previous state saved in the register cache
done before that unconditional enable.
Fixes: 6edfa11cb3 ("clk: samsung: Add enable/disable operation for PLL36XX clocks")
CC: stable@vger.kernel.org # v4.13
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
All users of __PLL macro already provide flags parameter, so don't
overwrite it unconditionally with CLK_GET_RATE_NOCACHE.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
* clk-pm-runtime:
clk: samsung: exynos-audss: Add support for runtime PM
clk: samsung: exynos-audss: Use local variable for controller's device
clk: samsung: exynos5433: Add support for runtime PM
clk: samsung: Add support for runtime PM
clk: Add support for runtime PM
The TOP "aclk400_mscl" clock should be kept enabled all the time
to allow proper access to power management control for MSC power
domain and devices that are a part of it. This change is required
for the scaler to work properly after domain power on/off sequence.
Fixes: 318fa46cc6 ("clk/samsung: exynos542x: mark some clocks as critical")
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Omit an extra message for a memory allocation failure
in exynos_register_cpu_clock() function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds support for runtime PM to Exynos Audio SubSystem driver to
enable full support for audio power domain on Exynos5 SoCs. The main change
is moving register saving and restoring code from system sleep PM ops to
runtime PM ops and implementing system sleep PM ops with generic
pm_runtime_force_suspend/resume helpers. Runtime PM of the Exynos AudSS
device is managed from clock core depending on the preparation status
of the provided clocks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1503302703-13801-6-git-send-email-m.szyprowski@samsung.com
Store pointer to the controller's device in local variable to avoid
extracting it from platform device in each call. This will also simplify
code in the future, when runtime PM support is added.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1503302703-13801-5-git-send-email-m.szyprowski@samsung.com
Add runtime pm support for all clock controller units (CMU), which belong
to power domains and require special handling during on/off operations.
Typically special values has to be written to MUX registers to change
internal clocks parents to OSC clock before turning power off. During such
operation all clocks, which enter CMU has to be enabled to let MUX to
stabilize. Also for each CMU there is one special parent clock, which has
to be enabled all the time when any access to CMU registers is being done.
This patch solves most of the mysterious external abort and freeze issues
caused by a lack of proper parent CMU clock enabled or incorrect turn off
procedure.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1503302703-13801-4-git-send-email-m.szyprowski@samsung.com
This patch adds struct device pointer to samsung_clk_provider and forwarding it
to clk_register_* functions, so drivers can register clocks, which use runtime
pm feature.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1503302703-13801-3-git-send-email-m.szyprowski@samsung.com
Changes in definitions of audio related clocks for Exynos5420/5422/5800
SoCs: a fix of mau_epll clock definition and changes enabling clock rate
setting propagation on a path from the I2S IP block up the EPLL.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pAH5
-----END PGP SIGNATURE-----
Merge tag 'clk-v4.14-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk into clk-next
Pull Samsung clk driver updates from Sylwester Nawrocki:
Changes in definitions of audio related clocks for Exynos5420/5422/5800
SoCs: a fix of mau_epll clock definition and changes enabling clock rate
setting propagation on a path from the I2S IP block up the EPLL.
* tag 'clk-v4.14-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk:
clk: samsung: exynos542x: Enable clock rate propagation up to the EPLL
clk: samsung: Add CLK_SET_RATE_PARENT to some AUDSS CLK CON clocks
clk: samsung: Fix mau_epll clock definition for exynos5422
The CLK_SET_RATE_PARENT flag is added to clocks between the EPLL
and the audio subsystem clock controller so that the EPLL's output
frequency can be set indirectly with clk_set_rate() on a leaf clock.
That should be safe as EPLL is normally only used to generate clock
for the audio subsystem.
With this change we can avoid passing the EPLL clock to the ASoC
machine driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This allows clk rate propagation up to the clock tree so EPLL
can be reprogrammed indirectly when setting rate of the Audio
Subsystem clocks.
The advantage is that sound machine driver can operate only
on the leaf clocks rather than explicitly re-configuring
the root clock (EPLL).
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Parent clock of the MAU_EPLL gate clock on exynos5422 is
"mout_user_mau_epll", not "mout_mau_epll_clk". This change
only affects exynos5422/5800.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch fixes values of the EPLL K coefficient and changes
the EPLL output frequency values to match exactly what is
possible to achieve with given M, P, S, K coefficients.
This allows to avoid rounding errors and unexpected frequency
being set with clk_set_rate(), due to recalc_rate returning
different values than the PLL rate specified in the
exynos5420_epll_24mhz_tbl table. E.g. this prevents a case
where two consecutive clk_set_rate() calls with same argument
result in different PLL output frequency.
The PLL output frequencies have been calculated with formula:
f = fxtal * (M * 2^16 + K) / (P * 2^S) / 2^16
where fxtal = 24000000.
Fixes: 9842452acd ("clk: samsung: exynos542x: Add EPLL rate table")
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Similarly to commit f1e9203e23 ("clk: samsung: Fix Exynos 5420 pinctrl
setup and clock disable failure due to domain being gated") for
Exynos5420, the Exynos4412 also requires that EPLL is not disabled.
Otherwise any access to MAUDIO block will silently halt.
This was not visible before because EPLL on Exynos4 could not be
disabled before commit 6edfa11cb3 ("clk: samsung:
Add enable/disable operation for PLL36XX clocks"). After this commit,
on Odroid U3 board one can see silent hang, usually with last (but
unrelated) messages:
[ 2.382741] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[ 2.405686] usb 1-3: new high-speed USB device number 3 using exynos-ehci
[ 2.419843] max77686-rtc max77686-rtc: setting system clock to 2017-06-21 17:04:13 UTC (1498064653)
Mark Exynos4 variant as also needed EPLL to be enabled all the time.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
A specific clock rate table is added for EPLL so it is possible
to set frequency of the EPLL output clock as multiple of various
audio sampling rates.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds missing definitions of mux clocks required for using
EPLL as the audio subsystem root clock on exynos5420/exynos5422 SoCs.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The existing enable/disable ops for PLL35XX are made more generic
and used also for PLL36XX. This fixes issues in the kernel with
PLL36XX PLLs when the PLL has not been already enabled by bootloader.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Clock providers should use the new struct clk_hw based API, so convert
Samsung S5PV210 Audio Subsystem clock provider to the new approach.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Clock providers should use the new struct clk_hw based API, so convert
Exynos CLKOUT clock provider to the new approach.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Clock providers should use the new struct clk_hw based API, so convert
Exynos Audio Subsystem clock provider to the new approach.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Clock providers should use the new struct clk_hw based API, so convert
Samsung clock providers and their helper functions to the new approach.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Add new variable to avoid using clk pointer for different purposes across
the exynos_register_cpu_clock() function. This will help in future rewrite
for the new clk_hw API.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
samsung_clk_register_pll2550x() function is not used anymore,
so remove its declaration.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
These functions are referencing s3c...._clk_regs[], which are marked as
__initdata. When compiling with CONFIG_DEBUG_SECTION_MISMATCH=y, this
produces warnings like
WARNING: vmlinux.o(.text+0x198350):
Section mismatch in reference from the function s3c2410_clk_sleep_init()
to the (unknown reference) .init.data:(unknown)
Mark the s3c...._clk_sleep_init() functions as __init in
order to fix this.
Fixes: ca2e90ac18 ("clk: samsung: add clock controller driver for s3c2412")
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Some PLLs might be disabled by default after turning off and then on
a power domain which they belongs to. To avoid configuring a disabled
PLL, add proper code for handling PLL enable/disable.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch fixes simple typos in Exynos5433 clocks driver. The SoC name
was referred a few times as '5443' instead of '5433'.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Default clock configuration applied by the bootloader for TM2 and TM2e
boards includes 250MHz and 278MHz rate for DISP PLL clock. To ensure
such configuration for those boards with 'assigned-clock-*' properties,
parameters for those two additional rates are needed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Add missing identifiers for phyclk_mipidphy0_bitclkdiv8_phy and
phyclk_mipidphy0_rxclkesc0_phy clocks. Access to those clocks is needed
to setup initial clock configuration for display subsystem in device tree
in order to avoid dependency on the configuration left by the bootloader.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
- addition of the CPU clock configuration data for Exynos4412
Prime SoC variant,
- removal of driver for deprecated Exynos4415 SoC,
- switching from the syscore to regular system sleep PM ops
in the audio subsystem clocks controller driver,
- updates of the definitions of some "Network On Chip" related
clocks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCAAGBQJYgPcFAAoJEE1bIKeAnHqLt9EP/0e5ljfUQRiczFvPVfUZeZb0
cn3HZrLBk+aDxDIBKpWSSUY0RraK6hjZYpwizRQyYBH7XFQY4aWxk2mtg+B5mPBT
OH02tjrFeQ+BG13BzYbMKg86jFrDqQEjlpMU6PHrILrQoRqoNBomlJXpC8Jw5Oqb
c79QxCsX8f94cbTgE3FHlF2ZHr8Wo4FKP2eWkdVBty1XvRvvZ1qE9IX6/wsqn1o7
WCoJpKq7UjX1U9gBeHZzFRgzpKjsSoSha7yW/CkxP6b0TksQUmGi81asFxdslqi3
xiK0PlsXB2R7TKNLNhU4hGcV7lvQFJaPOdWshvnQ7nFz9dlFjZkSGUTvLGYLH2+j
43nHnHqEP6avNYo5cBR27Wc2ZaARMXq7AMJvZHC2/DuhtaO70wKfFVib1nFe40pX
UBP5dxOy7C2taRxSr3QSmviuBwZYBmDWioE3SQE/IdM6z3WpN37kNrNw1OrMctji
MFCyIfeKlUpLJVZRcdKKxvem0QTPN5/cWote5ibNO+x0O9RWkXSrdBtnoioc5oL7
30TtZlGbKG9VsRRjxYhuul/lpTZvyewg5PP9T5xGmeXOF69SlPuZwOu26D3E2Lej
AiTMellqH7vjX2uNSQ4lQExzOj8psJ0Mq7hj5lRavsPn8m50PAHMfq+YHncii32I
E1HZF4sh7MYozX/2Els3
=mSQz
-----END PGP SIGNATURE-----
Merge tag 'clk-v4.11-samsung' of git://linuxtv.org/snawrocki/samsung into clk-next
Pull Samsung clk updates from Sylwester Nawrocki:
- addition of the CPU clock configuration data for Exynos4412
Prime SoC variant,
- removal of driver for deprecated Exynos4415 SoC,
- switching from the syscore to regular system sleep PM ops
in the audio subsystem clocks controller driver,
- updates of the definitions of some "Network On Chip" related
clocks.
* tag 'clk-v4.11-samsung' of git://linuxtv.org/snawrocki/samsung:
clk: samsung: Remove Exynos4415 driver (SoC not supported anymore)
clk: samsung: exynos-audss: Replace syscore PM with platform device PM
clk: samsung: exynos5433: Set NoC (Network On Chip) clocks as critical
clk: samsung: Add CPU clk configuration data for Exynos4412 Prime
Support for Exynos4415 is going away because there are no internal nor
external users.
Since commit 46dcf0ff0d ("ARM: dts: exynos: Remove exynos4415.dtsi"),
the platform cannot be instantiated so remove also the drivers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Some parent clocks of the Exynos542x clock blocks, which have separate
power domains (like DISP, MFC, MSC, GSC, FSYS and G2D) must be always
enabled to access any register related to power management unit or devices
connected to it. For the time being, until a proper solution based on
runtime PM is applied, mark those clocks as critical (instead of ignore
unused or even no flags) to prevent disabling them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> [Exynos5800 Peach Pi Chromebook]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Exynos AUDSS clock driver has been already converted to platform driver,
so remove the dependency on the syscore ops - the last remaining
non-platform driver feature. Platform device's system sleep PM provides
all needed infrastructure for replacing syscore-based PM, so do it now.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The ACLK_BUS0/1/2 are used for NoC (Network on Chip). If NoC's clocks are
disabled, the system halt happens. Following clocks must be always enabled:
- CLK_ACLK_BUS0_400 : NoC's bus clock for PERIC/PERIS/FSYS/MSCL,
- CLK_ACLK_BUS1_400 : NoC's bus clock for MFC/HEVC/G3D,
- CLK_ACLK_BUS2_400 : NoC's bus clock for GSCL/DISP/G2D/CAM0/CAM1/ISP.
This patch also adds the CLK_SET_RATE_PARENT flag to the CLK_SCLK_JPEG_MSCL
because this clock should be used for bus frequency scaling. This clock need
to be changed on the fly with CLK_SET_RATE_PARENT flag.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Add cpu clock configuration data for Exynos4412 Prime SoC
(it supports additional PLL rates & CPU frequencies).
Based on Hardkernel's kernel for ODROID-X2/U2/U3 boards.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
- addition of missing documentation and DT properties for the CMU_AUD
block source clocks,
- correction of CMU_FSYS parent clock definition,
- marking as critical clocks which have to be enabled in order
to access control registers of child CMUs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oQKk
-----END PGP SIGNATURE-----
Merge tag 'clk-v4.10-exynos5433' of git://linuxtv.org/snawrocki/samsung into clk-next
Pull Exynos5433 SoC updates from Sylwester Nawrocki:
- addition of missing documentation and DT properties for the CMU_AUD
block source clocks,
- correction of CMU_FSYS parent clock definition,
- marking as critical clocks which have to be enabled in order
to access control registers of child CMUs.
* tag 'clk-v4.10-exynos5433' of git://linuxtv.org/snawrocki/samsung:
clk: exynos5433: Mark some clocks as critical
clk: exynos5433: Add documentation for the audio block parent clocks
clk: exynos5433: Fix parent clocks for FSYS block
Some parent clocks of the Exynos5433 CMUs must be always enabled to access
any register in the given CMU or devices connected to it. For the time
being, until a proper solution based on runtime PM is applied, mark those
clocks as critical (instead of ignore unused) to prevent disabling them.
Reported-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The proper parent clock for FSYS block is "aclk_fsys_200"
according to the Exynos5433 reference manual.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The Exynos PMU node is an interrupt, clock and PMU (Power Management Unit)
controller, and these functionalities are supported by different drivers
that matches the same compatible strings.
Since commit 989eafd0b6 ("clk: core: Avoid double initialization of
clocks") the OF core flags clock controllers registered with the
CLK_OF_DECLARE() macro as OF_POPULATED, so platform devices with the same
compatible string will not be registered.
This prevents the PMU platform device to be created, so the Exynos PMU
driver is never probed. This breaks (among other things) Suspend-to-RAM.
Fix this by changing CLKOUT driver initialization method to
CLK_OF_DECLARE_DRIVER(), which doesn't clear the OF_POPULATED flag, so
later a platform device is created and the Exynos PMU platform driver
can be be probed properly.
Fixes: 989eafd0b6 ("clk: core: Avoid double initialization of clocks")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/clk/samsung/clk-exynos-audss.ko | grep alias
alias: platform:exynos-audss-clk
After this patch:
$ modinfo drivers/clk/samsung/clk-exynos-audss.ko | grep alias
alias: platform:exynos-audss-clk
alias: of:N*T*Csamsung,exynos5420-audss-clockC*
alias: of:N*T*Csamsung,exynos5420-audss-clock
alias: of:N*T*Csamsung,exynos5410-audss-clockC*
alias: of:N*T*Csamsung,exynos5410-audss-clock
alias: of:N*T*Csamsung,exynos5250-audss-clockC*
alias: of:N*T*Csamsung,exynos5250-audss-clock
alias: of:N*T*Csamsung,exynos4210-audss-clockC*
alias: of:N*T*Csamsung,exynos4210-audss-clock
Fixes: 4d252fd571 ("clk: samsung: Allow modular build of the Audio Subsystem CLKCON driver")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds code instantiating the EPLL, which is used as the
audio subsystem's root clock.
The requirement to specify the external root clock in clocks property
is documented. Having the consumer 'clocks' property ensures proper
initialization order by explicitly specifying dependencies in DT.
It prevents situations when the SoC's clock controller driver has
initialized, the external oscillator clock is not yet registered
and setting clock frequencies through assigned-clock-rates property
doesn't work properly due to unknown external oscillator frequency.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
There is no need to log probe() completion in normal conditions
so the "setup completed" log is removed.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Exynos5410 Audio Subsystem Clock Controller, comparing to the already
supported IP block revisions, has additionally an I2S_MST divider
so a new compatible string is added.
It is not clear from the Exynos5410 User's Manual released on 2012.03.09
where in the clock tree the I2S_MST clock divider can be found exactly
so this clock is left unimplemented for now.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
There is no such significant differences in pll2550x PLL type
to justify a separate registration function. This patch adapts
exynos5440 driver to use the common function and removes
samsung_clk_register_pll2550x().
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds the mux/divider clocks for CMU_CDREX (DRAM Express
Controller) which generates the clocks for DRAM and NoC (Network on Chip)
bus. There is differnet source of MUX_MX_MSPLL_CCORE between exynos5420
and exynos5422, so each MUX_MX_MSPLL_CCORE uses the different parent source
group.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch uses the samsung_cmu_register_one() to simplify code
and move the pll/mux/div/gate data to initconst section.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch moves the samsung_cmu_info struct instances to initconst
section, this decreases the kernel image size by 784 bytes, which makes
zImage smaller by 480 bytes.
The patch increases .init.rodata section size by 780 bytes but decreases
.init.text section size by 1564 bytes.
Size of the drivers/clk/samsung/clk-exynos5260.o object file is 29100
bytes without the patch and 28316 after applying the patch.
The section size differences are as below:
15c15
< 3 .init.text 000006b8 00000000 00000000 00000034 2**2
---
> 3 .init.text 0000009c 00000000 00000000 00000034 2**2
25c25
< 8 .init.rodata 00003f6c 00000000 00000000 00002f20 2**2
---
> 8 .init.rodata 00004278 00000000 00000000 00002904 2**2
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Any clock dependencies can be properly handled with deferred probing
so we can remove core_initcall and switch to a proper loadable platform
driver module.
This change has been tested on Exynos4412 Odroid U3 based board.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1467987300-31450-1-git-send-email-s.nawrocki@samsung.com
The Kconfig currently controlling compilation of this code is:
arch/arm/mach-s5pv210/Kconfig:config ARCH_S5PV210
arch/arm/mach-s5pv210/Kconfig: bool "Samsung S5PV210/S5PC110" if ARCH_MULTI_V7
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since this code is already not using module_init, case, the init
ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tags etc. since all that information
is already contained at the top of the file in the comments.
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160704211220.5685-8-paul.gortmaker@windriver.com
Because the Exynos5433 SPI driver supports the ioclk handling and
the following patch:
http://marc.info/?l=linux-kernel&m=146787645626318&w=2
fixes a synchronus abort issue, none of the SPI clocks require
any critical handling: remove, then, the CLK_IGNORE_UNUSED flag
for the SPI related clocks.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1468317736-18841-8-git-send-email-andi.shyti@samsung.com
This patch adds the CLK_IGNORE_UNUSED flag for PCI Express's clocks
which need to remain enabled. The 'pcie' gate clock definition is
also added.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[s.nawrocki@samsung.com: edited the patch's summary]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Some clocks are required to be unmasked during suspend to RAM. Otherwise
the PMU will stuck and the power down sequence will never be completed.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[s.nawrocki@samsung.com: edited the patch's summary]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds CLK_IGNORE_UNUSED flag for sclk_aud_uart gate
clock for uart3 operation.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[s.nawrocki@samsung.com: edited the patch's summary]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Use the byte-order aware big endian accessors, allowing for kernels
running under big-endian.
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Fix the clk endian access code to deal with kernels built for big endian
operation.
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Add the CPU clocks configuration data and instantiate the CPU clocks
type for Exynos5433.
Cc: Kukjin Kim <kgene@kernel.org>
CC: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Exynos5433 uses different register layout for CPU clock registers
than earlier SoCs so add new code for handling this layout. Also
add new CLK_CPU_HAS_E5433_REGS_LAYOUT flag to request using it.
There should be no functional change resulting from this patch.
Cc: Kukjin Kim <kgene@kernel.org>
CC: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Open-code samsung_cmu_register_one() calls for CMU_APOLLO and
CMU_ATLAS setup code as a preparation for adding CPU clocks
support for Exynos5433.
There should be no functional change resulting from this patch.
Cc: Kukjin Kim <kgene@kernel.org>
CC: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Although unbinding a driver requires root privileges but it still might
be used theoretically in certain attacks (by triggering NULL pointer
exception or memory corruption if driver does not provide proper remove
callbacks or core does not handle it).
Samsung clock drivers are essential for system operation so their
removal is not expected. More over, the Exynos3250 ISP clock driver does
not implement remove() driver callback and it is not buildable as
modules.
Suppress the unbind interface for Exynos3250 ISP and S3C2410 DCLK clock
drivers.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The aclk333 clock needs to be ungated during the MFC power domain switch,
so set the clock ID to allow the Exynos power domain logic to lookup this
clock if is defined in the MFC PD device tree node.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
