When working in slave mode it seems the timing is exceedingly tight.
The TX FIFO can never empty, because the master is driving the clock so
zeros would be sent for those bytes where the FIFO is empty.
Return to interleaving the writing of the TX FIFO and the reading
of the RX FIFO to try to ensure the data is available when required.
Fixes: a84c11e16d ("spi: spi-cadence: Avoid read of RX FIFO before its ready")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230518093927.711358-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
New set/get APIs for accessing spi->chip_select were introduced by
'commit 9e264f3f85 ("spi: Replace all spi->chip_select and spi->cs_gpiod
references with function call")', but the 'commit 2c8606040a ("spi: dw:
Add support for AMD Pensando Elba SoC")' uses the old interface by directly
accessing spi->chip_select. So, replace all spi->chip_select references
in the driver with new get/set APIs.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com
Acked-by: Serge Semin <fancer.lancer@gmail.com
Link: https://lore.kernel.org/r/20230515130343.63770-1-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org
Commit b1b90514ea ("spi: spi-cadence: Add support for Slave mode")
updated the code to trigger the IRQ when the FIFO was half empty,
overlapping filling more data into the FIFO and sending what is left.
This appears to cause regressions on the Zynq 7000, for transactions
longer than the FIFO size, below that no overlapping occurs.
It would appear from my testing that any attempt to put new data into
the FIFO whilst data is still transmitting causes data corruption
on both send and receive. If I am reading the commit message right
on commit 49530e6411 ("spi: cadence: Add usleep_range() for
cdns_spi_fill_tx_fifo()"), that would also seem to imply this is the
case.
On the assumption that this isn't an issue on the platform
the original slave mode support was added for, update the
cdns_transfer_one to only set the watermark to 50% of the FIFO size
when in slave mode. There by retaining the new behaviour for slave
mode but reverting to the older behaviour when the SPI is used a
master.
Fixes: b1b90514ea ("spi: spi-cadence: Add support for Slave mode")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230509164153.3907694-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org
Recent changes to cdns_spi_irq introduced some issues.
Firstly, when writing the end of a longer transaction, the code in
cdns_spi_irq will write data into the TX FIFO, then immediately
fall into the if (!xspi->tx_bytes) path and attempt to read data
from the RX FIFO. However this required waiting for the TX FIFO to
empty before the RX data was ready.
Secondly, the variable trans_cnt is now rather inaccurately named
since in cases, where the watermark is set to 1, trans_cnt will be
1 but the count of bytes transferred would be much longer.
Finally, when setting up the transaction we set the watermark to 50%
of the FIFO if the transaction is great than 50% of the FIFO. However,
there is no need to split a tranaction that is smaller than the
whole FIFO, so anything up to the FIFO size can be done in a single
transaction.
Tidy up the code a little, to avoid repeatedly calling
cdns_spi_read_rx_fifo with a count of 1, and correct the three issues
noted above.
Fixes: b1b90514ea ("spi: spi-cadence: Add support for Slave mode")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230509164153.3907694-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org
Spi geni driver switches between FIFO and DMA modes based on xfer length.
FIFO mode relies on M_CMD_DONE_EN interrupt for completion while DMA mode
relies on XX_DMA_DONE.
During dynamic switching, if FIFO mode is chosen, FIFO related interrupts
are enabled and DMA related interrupts are disabled. And viceversa.
Chip select shares M_CMD_DONE_EN interrupt with FIFO to check completion.
Now, if a chip select operation is preceded by a DMA xfer, M_CMD_DONE_EN
interrupt would have been disabled and hence it will never receive one
resulting in timeout.
For chip select, in addition to setting the xfer mode to FIFO,
select_mode() to FIFO so that required interrupts are enabled.
Fixes: e5f0dfa78a ("spi: spi-geni-qcom: Add support for SE DMA mode")
Suggested-by: Praveen Talari <quic_ptalari@quicinc.com
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com
Reviewed-by: Douglas Anderson <dianders@chromium.org
Link: https://lore.kernel.org/r/1683626496-9685-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org
Here is the "big" set of char/misc and other driver subsystems for
6.4-rc1.
It's pretty big, but due to the removal of pcmcia drivers, almost breaks
even for number of lines added vs. removed, a nice change.
Included in here are:
- removal of unused PCMCIA drivers (finally!)
- Interconnect driver updates and additions
- Lots of IIO driver updates and additions
- MHI driver updates
- Coresight driver updates
- NVMEM driver updates, which required some OF updates
- W1 driver updates and a new maintainer to manage the subsystem
- FPGA driver updates
- New driver subsystem, CDX, for AMD systems
- lots of other small driver updates and additions
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp5Eg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynSXgCg0kSw3vUYwpsnhAsQkoPw1QVA23sAn2edRCMa
GEkPWjrROueCom7xbLMu
=eR+P
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc drivers updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystems for
6.4-rc1.
It's pretty big, but due to the removal of pcmcia drivers, almost
breaks even for number of lines added vs. removed, a nice change.
Included in here are:
- removal of unused PCMCIA drivers (finally!)
- Interconnect driver updates and additions
- Lots of IIO driver updates and additions
- MHI driver updates
- Coresight driver updates
- NVMEM driver updates, which required some OF updates
- W1 driver updates and a new maintainer to manage the subsystem
- FPGA driver updates
- New driver subsystem, CDX, for AMD systems
- lots of other small driver updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (196 commits)
mcb-lpc: Reallocate memory region to avoid memory overlapping
mcb-pci: Reallocate memory region to avoid memory overlapping
mcb: Return actual parsed size when reading chameleon table
kernel/configs: Drop Android config fragments
virt: acrn: Replace obsolete memalign() with posix_memalign()
spmi: Add a check for remove callback when removing a SPMI driver
spmi: fix W=1 kernel-doc warnings
spmi: mtk-pmif: Drop of_match_ptr for ID table
spmi: pmic-arb: Convert to platform remove callback returning void
spmi: mtk-pmif: Convert to platform remove callback returning void
spmi: hisi-spmi-controller: Convert to platform remove callback returning void
w1: gpio: remove unnecessary ENOMEM messages
w1: omap-hdq: remove unnecessary ENOMEM messages
w1: omap-hdq: add SPDX tag
w1: omap-hdq: allow compile testing
w1: matrox: remove unnecessary ENOMEM messages
w1: matrox: use inline over __inline__
w1: matrox: switch from asm to linux header
w1: ds2482: do not use assignment in if condition
w1: ds2482: drop unnecessary header
...
Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening in
the driver core in the quest to be able to move "struct bus" and "struct
class" into read-only memory, a task now complete with these changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules for
all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most of
them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp7Sw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykitQCfamUHpxGcKOAGuLXMotXNakTEsxgAoIquENm5
LEGadNS38k5fs+73UaxV
=7K4B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
A fairly standard release for SPI with the exception of a change to the
API for specifying chip selects done in preparation for supporting
devices with more than one chip select, this required some mechanical
changes throughout the tree which have been cooking in -next happily for
a while. There's also a new API to allow us to TPM chips on half duplex
controllers.
There's three commits in here that were mangled by a bad interaction
between the alsa-devel mailing list software and b4, I didn't notice
until there were merges on top with it being SPI not ALSA. It seemed
clear enough to not be worth going back and fixing.
- Refactoring in preparation for supporting multiple chip selects for a
single device, needed by some flash devices, which required a change
in the SPI device API visible throughout the tree.
- Support for hardware assisted interaction with SPI TPMs on half
duplex controllers, implemented on nVidia Tedra210 QuadSPI.
- Optimisation for large transfers on fsl-cpm devices.
- Cleanups around device property use which fix some sisues with
fwnode.
- Use of both void remove() and devm_platform_.*ioremap_resource().
- Support for AMD Pensando Elba, Amlogic A1, Cadence device mode,
Intel MetorLake-S and StarFive J7110 QuadSPI.
The final commit converting to DEV_PM_OPS() was applied late to fix a
warning that was introduced by some of the earlier work.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmRIFQgACgkQJNaLcl1U
h9BJOwf+JF2RySdn5g1LsyTndPZhLfw4iJgTHaMlnv5tiPHvYVYMM/mNMbMr5Znh
Y2T0OUkzuRfOK273C+hItC1bTYFTa2cEbDb5dpmKBOZdQ3hjGsZQBvuH2bScUQ+a
H7UgD3FYOJST6k6rRgZQxVMPePFrXAOaO1gmFWTR3v1EcEr2JeQnjZsmymFXcTnc
CtPg9N3RvhVnq5aXuxSgQeyyKIjo4LJh/eZ2mexPIu0DeUq3MftaWwSwCXFIoeNC
DMLA4mZWTgf/yt6JUALwLr+bIiJjb4qGjp3xGZ2wmX7zn73f9QQvuunKb1V4zbNF
EdXLo2VjA9cZjsihenBaKeHnkfgNfA==
=IRqY
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly standard release for SPI with the exception of a change to
the API for specifying chip selects done in preparation for supporting
devices with more than one chip select, this required some mechanical
changes throughout the tree which have been cooking in -next happily
for a while.
There's also a new API to allow us to support TPM chips on half duplex
controllers.
Summary:
- Refactoring in preparation for supporting multiple chip selects for
a single device, needed by some flash devices, which required a
change in the SPI device API visible throughout the tree
- Support for hardware assisted interaction with SPI TPMs on half
duplex controllers, implemented on nVidia Tedra210 QuadSPI
- Optimisation for large transfers on fsl-cpm devices
- Cleanups around device property use which fix some sisues with
fwnode
- Use of both void remove() and devm_platform_.*ioremap_resource()
- Support for AMD Pensando Elba, Amlogic A1, Cadence device mode,
Intel MetorLake-S and StarFive J7110 QuadSPI"
* tag 'spi-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (185 commits)
spi: bcm63xx: use macro DEFINE_SIMPLE_DEV_PM_OPS
spi: tegra210-quad: Enable TPM wait polling
spi: Add TPM HW flow flag
spi: bcm63xx: remove PM_SLEEP based conditional compilation
spi: cadence-quadspi: use macro DEFINE_SIMPLE_DEV_PM_OPS
spi: spi-cadence: Add support for Slave mode
spi: spi-cadence: Switch to spi_controller structure
spi: cadence-quadspi: fix suspend-resume implementations
spi: dw: Add support for AMD Pensando Elba SoC
spi: dw: Add AMD Pensando Elba SoC SPI Controller
spi: cadence-quadspi: Disable the SPI before reconfiguring
spi: cadence-quadspi: Update the read timeout based on the length
spi: spi-loopback-test: Add module param for iteration length
spi: add support for Amlogic A1 SPI Flash Controller
dt-bindings: spi: add Amlogic A1 SPI controller
spi: fsl-spi: No need to check transfer length versus word size
spi: fsl-spi: Change mspi_apply_cpu_mode_quirks() to void
spi: fsl-cpm: Use 16 bit mode for large transfers with even size
spi: fsl-spi: Re-organise transfer bits_per_word adaptation
spi: fsl-spi: Fix CPM/QE mode Litte Endian
...
Using this macro makes the code more readable.
It also inits the members of dev_pm_ops in the following manner
without us explicitly needing to:
.suspend = bcm63xx_spi_suspend, \
.resume = bcm63xx_spi_resume, \
.freeze = bcm63xx_spi_suspend, \
.thaw = bcm63xx_spi_resume, \
.poweroff = bcm63xx_spi_suspend, \
.restore = bcm63xx_spi_resume
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230424102546.1604484-1-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Krishna Yarlagadda <kyarlagadda@nvidia.com>:
TPM devices may insert wait state on last clock cycle of ADDR phase.
For SPI controllers that support full-duplex transfers, this can be
detected using software by reading the MISO line. For SPI controllers
that only support half-duplex transfers, such as the Tegra QSPI, it is
not possible to detect the wait signal from software. The QSPI
controller in Tegra234 and Tegra241 implement hardware detection of the
wait signal which can be enabled in the controller for TPM devices.
Add a flag for this in the SPI core and implement support in the Tegra
QuadSPI driver.
Trusted Platform Module requires flow control. As defined in TPM
interface specification, client would drive MISO line at same cycle as
last address bit on MOSI.
Tegra234 and Tegra241 QSPI controllers have TPM wait state detection
feature which is enabled for TPM client devices reported in SPI device
mode bits.
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20230421091309.2672-4-kyarlagadda@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Get rid of conditional compilation based on CONFIG_PM_SLEEP because
it may introduce build issues with certain configs where it maybe disabled
This is because if above config is not enabled the suspend-resume
functions are never part of the code but the bcm63xx_spi_pm_ops struct
still inits them to non-existent suspend-resume functions.
Fixes: b42dfed83d ("spi: add Broadcom BCM63xx SPI controller driver")
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230420121615.967487-1-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Using this macro makes the code more readable.
It also inits the members of dev_pm_ops in the following manner
without us explicitly needing to:
.suspend = cqspi_suspend, \
.resume = cqspi_resume, \
.freeze = cqspi_suspend, \
.thaw = cqspi_resume, \
.poweroff = cqspi_suspend, \
.restore = cqspi_resume
Also get rid of conditional compilation based on CONFIG_PM_SLEEP because
it introduces build issues with certain configs when CQSPI_DEV_PM_OPS is
just NULL.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304191900.2fARFQW9-lkp@intel.com/
Fixes: 1406234105 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230420054257.925092-1-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A small fix in the error handling for the rockchip driver, ensuring we
don't leak clock enables if we fail to request the interrupt for the
device.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmRATd4ACgkQJNaLcl1U
h9ApHAf/UdN/irP26Nyn2kyrZxxO2S7Ix22PR5uDaD5+YvCTUCPYVzRbSq5T3LQZ
Znm124tdz3Fwppmw06q7V1AAu4jtzdOKwiocdUn+KV1XH/WMdOOy7El7Fp71QVu1
8i8Dqt35KwRN1z1d/ts0ubDUFa+s6tEFaYIMtlcDLVSAJMwGEz9YCNBAMDqlINGc
jSccxA1vIm3xyVOhoAN/W0grivW6oEBVfaG5OlkX2MS+PZQUGy+IMHjVPCIxT5P4
s/eKrcQXOhuUS3WmIsvF1ynKsb7kSk2x4NgX2vZB+t2NIK9Z5P5sHlnpcuZXhF/t
peo8lR03e5okSDoL1x5vgej0hwFjQQ==
=eeQQ
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fix from Mark Brown:
"A small fix in the error handling for the rockchip driver, ensuring we
don't leak clock enables if we fail to request the interrupt for the
device"
* tag 'spi-fix-v6.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-rockchip: Fix missing unwind goto in rockchip_sfc_probe()
If devm_request_irq() fails, then we are directly return 'ret' without
clk_disable_unprepare(sfc->clk) and clk_disable_unprepare(sfc->hclk).
Fix this by changing direct return to a goto 'err_irq'.
Fixes: 0b89fc0a36 ("spi: rockchip-sfc: add rockchip serial flash controller")
Signed-off-by: Li Lanzhe <u202212060@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230419115030.6029-1-u202212060@hust.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Srinivas Goud <srinivas.goud@amd.com>:
Currently SPI Cadence controller works in Master mode only.
Update driver to support Slave mode and also Full duplex transfer
support in Slave mode
Currently SPI Cadence controller works only in Master mode.
Updated interrupt handler for Full duplex transfer in Slave mode.
Interrupt handler rely on the TX empty interrupt even for Slave mode
transfer due to below HW limitation.
HW limitation:
AR 65885 - SPI Controller Might Not Update RX_NEMPTY Flag, Showing
Incorrect Status Of The Receive FIFO
SPI Slave mode works in the following manner:
1. One transfer can be finished only after all transfer->len
data been transferred to master device.
2. Slave device only accepts transfer->len data. Any data longer
than this from master device will be dropped. Any data shorter than
this from master will cause SPI to be stuck due to the above behavior.
3. The stale data present in RXFIFO will be dropped in unprepared
hardware transfer function.
Signed-off-by: Srinivas Goud <srinivas.goud@amd.com>
Link: https://lore.kernel.org/r/1681825625-10265-3-git-send-email-srinivas.goud@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace spi_master structure with spi_controller structure.
spi_controller structure provides interface support for
both SPI master and slave controller.
Signed-off-by: Srinivas Goud <srinivas.goud@amd.com>
Link: https://lore.kernel.org/r/1681825625-10265-2-git-send-email-srinivas.goud@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The cadence QSPI driver misbehaves after performing a full system suspend
resume:
...
spi-nor spi0.0: resume() failed
...
This results in a flash connected via OSPI interface after system suspend-
resume to be unusable.
fix these suspend and resume functions.
Fixes: 1406234105 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230417091027.966146-3-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>:
Update Xilinx Versal external DMA read logic to fix random issues
- Instead of having the fixed timeout, update the read timeout based on
the length of the transfer to avoid timeout for larger data size.
- While switching between external DMA read and indirect read, disable the
SPI before configuration and enable it after configuration as recommended
by Octal-SPI Flash Controller specification.
Sai Krishna Potthuri (2):
spi: cadence-quadspi: Update the read timeout based on the length
spi: cadence-quadspi: Disable the SPI before reconfiguring
drivers/spi/spi-cadence-quadspi.c | 40 ++++++++++++++++++-------------
1 file changed, 24 insertions(+), 16 deletions(-)
--
2.25.1
The AMD Pensando Elba SoC includes a DW apb_ssi v4 controller
with device specific chip-select control. The Elba SoC
provides four chip-selects where the native DW IP supports
two chip-selects. The Elba DW_SPI instance has two native
CS signals that are always overridden.
Signed-off-by: Brad Larson <blarson@amd.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20230410184526.15990-11-blarson@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Observed random DMA timeout failures while doing back to back
transfers which involves switching the modes from DMA to NON-DMA.
This issue is observed while testing the OSPI+UBIFS file system test case
where rootfs is mounted from OSPI UBIFS partition.
To avoid this issue, disable the SPI before changing the configuration
from external DMA to NON-DMA and vice versa and reenable it after changing
the configuration.
As per the Cadence Octal SPI design specification, it is recommended to
disable the Octal-SPI enable bit before reconfiguring.
Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Link: https://lore.kernel.org/r/20230320095931.2651714-3-sai.krishna.potthuri@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When performing indirect read via external DMA the timeout for
completion is set equal to the read length instead of fixed timeout value.
For reads larger than 500 bytes, the timeout will continue to be
equal to the read length whereas for a small read like the Read Status
Register command, the timeout would be 1 or 2 milliseconds. This is not
enough to cover the overhead needed in setting up DMA, in that case make
sure the timeout is at least 500ms to allow DMA to finish. This solution
is inline with the timeout used for Direct read via DMA.
Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Link: https://lore.kernel.org/r/20230320095931.2651714-2-sai.krishna.potthuri@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Fix interaction between fw_devlink and DT overlays causing
devices to not be probed
- Fix the compatible string for loongson,cpu-interrupt-controller
-----BEGIN PGP SIGNATURE-----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=x2A8
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-6.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Fix interaction between fw_devlink and DT overlays causing devices to
not be probed
- Fix the compatible string for loongson,cpu-interrupt-controller
* tag 'devicetree-fixes-for-6.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
treewide: Fix probing of devices in DT overlays
dt-bindings: interrupt-controller: loongarch: Fix mismatched compatible
SPI test framework is designed to run each test case for
a list of lengths.
Introduce a module parameter to limit the iterations
to a single value among the list of lengths.
Signed-off-by: Rohit Ner <rohitner@google.com>
Link: https://lore.kernel.org/r/20230412202009.3750955-2-rohitner@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When loading a DT overlay that creates a device, the device is not
probed, unless the DT overlay is unloaded and reloaded again.
After the recent refactoring to improve fw_devlink, it no longer depends
on the "compatible" property to identify which device tree nodes will
become struct devices. fw_devlink now picks up dangling consumers
(consumers pointing to descendent device tree nodes of a device that
aren't converted to child devices) when a device is successfully bound
to a driver. See __fw_devlink_pickup_dangling_consumers().
However, during DT overlay, a device's device tree node can have
sub-nodes added/removed without unbinding/rebinding the driver. This
difference in behavior between the normal device instantiation and
probing flow vs. the DT overlay flow has a bunch of implications that
are pointed out elsewhere[1]. One of them is that the fw_devlink logic
to pick up dangling consumers is never exercised.
This patch solves the fw_devlink issue by marking all DT nodes added by
DT overlays with FWNODE_FLAG_NOT_DEVICE (fwnode that won't become
device), and by clearing the flag when a struct device is actually
created for the DT node. This way, fw_devlink knows not to have
consumers waiting on these newly added DT nodes, and to propagate the
dependency to an ancestor DT node that has the corresponding struct
device.
Based on a patch by Saravana Kannan, which covered only platform and spi
devices.
[1] https://lore.kernel.org/r/CAGETcx_bkuFaLCiPrAWCPQz+w79ccDp6=9e881qmK=vx3hBMyg@mail.gmail.com
Fixes: 4a032827da ("of: property: Simplify of_link_to_phandle()")
Link: https://lore.kernel.org/r/CAGETcx_+rhHvaC_HJXGrr5_WAd2+k5f=rWYnkCZ6z5bGX-wj4w@mail.gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Saravana Kannan <saravanak@google.com>
Tested-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Link: https://lore.kernel.org/r/e1fa546682ea4c8474ff997ab6244c5e11b6f8bc.1680182615.git.geert+renesas@glider.be
Signed-off-by: Rob Herring <robh@kernel.org>
This is a driver for the Amlogic SPI flash controller support
on A113L SoC.
Signed-off-by: Martin Kurbanov <mmkurbanov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230403183217.13280-3-mmkurbanov@sberdevices.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
This helper does not produce a real modalias, but tries to get the
"product" compatible part of the "vendor,product" compatibles only. It
is far from creating a purely useful modalias string and does not seem
to be used like that directly anyway, so let's try to give this helper a
more meaningful name before moving there a real modalias helper (already
existing under of/device.c).
Also update the various documentations to refer to the strings as
"aliases" rather than "modaliases" which has a real meaning in the Linux
kernel.
There is no functional change.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Wolfram Sang <wsa@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Link: https://lore.kernel.org/r/20230404172148.82422-9-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge series from Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>:
This patch series fixes the following bugs in spi-pci1xxxx driver:
1. Length of SPI transactions is improper
2. SPI transactions fail after suspend and resume
3. Incorrect implementation of pci1xxxx_spi_set_cs API
mspi_apply_cpu_mode_quirks() always returns the passed bits_per_word
unmodified.
Make it return void, then don't check bits_per_word anymore on
return as it doesn't change.
bits_per_word is already checked by __spi_validate() so no risk to
have bits_per_word higher than 32.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/3142a7c40af12a160f4e134764f2c34da3d8e1e2.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped as seen in a previous commit.
So, for large tranfers with an even size, allocate a temporary tx
buffer and byte-swap data before and after transfer.
This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.
For the time being, only do it on CPM1 as there must be a
trade-off between the CPM load reduction and the CPU load required
to byte swap the data.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f2e981f20f92dd28983c3949702a09248c23845c.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
For different reasons, fsl-spi driver performs bits_per_word
modifications for different reasons:
- On CPU mode, to minimise amount of interrupts
- On CPM/QE mode to work around controller byte order
For CPU mode that's done in fsl_spi_prepare_message() while
for CPM mode that's done in fsl_spi_setup_transfer().
Reunify all of it in fsl_spi_prepare_message(), and catch
impossible cases early through master's bits_per_word_mask
instead of returning EINVAL later.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/0ce96fe96e8b07cba0613e4097cfd94d09b8919a.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
CPM has the same problem as QE so for CPM also use the fix added
by commit 0398fb7094 ("spi/spi_mpc8xxx: Fix QE mode Litte Endian"):
CPM mode uses Little Endian so words > 8 bits are byte swapped.
Workaround this by always enforcing wordsize 8 for 16 and 32 bits
words. Unfortunately this will not work for LSB transfers
where wordsize is > 8 bits so disable these for now.
Also limit the workaround to 16 and 32 bits words because it can
only work for multiples of 8-bits.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Fixes: 0398fb7094 ("spi/spi_mpc8xxx: Fix QE mode Litte Endian")
Link: https://lore.kernel.org/r/1b7d3e84b1128f42c1887dd2fb9cdf390f541bc1.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Hardware does not have support to disable individual chip select lines.
Disable all chip select lines by using SPI_FORCE_CE bit.
Fixes: 1cc0cbea71 ("spi: microchip: pci1xxxx: Add driver for SPI controller of PCI1XXXX PCIe switch")
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Link: https://lore.kernel.org/r/20230404171613.1336093-4-tharunkumar.pasumarthi@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pci1xxxx_spi_resume API masks SPI interrupt bit which prohibits interrupt
from coming to the host at the end of the transaction after suspend-resume.
This patch unmasks this bit at resume.
Fixes: 1cc0cbea71 ("spi: microchip: pci1xxxx: Add driver for SPI controller of PCI1XXXX PCIe switch")
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Link: https://lore.kernel.org/r/20230404171613.1336093-3-tharunkumar.pasumarthi@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In pci1xxxx_spi_transfer_one API, length of SPI transaction gets cleared
by setting of length mask. Set length of transaction only after masking
length field.
Fixes: 1cc0cbea71 ("spi: microchip: pci1xxxx: Add driver for SPI controller of PCI1XXXX PCIe switch")
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Link: https://lore.kernel.org/r/20230404171613.1336093-2-tharunkumar.pasumarthi@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Uwe Kleine-König <u.kleine-koenig@pengutronix.de>:
After fixing the error handling in the .remove() callback of the qup
driver, convert it to .remove_new() preparing to make platform driver's
remove functions return void.
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230330210341.2459548-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
According to commit 890cc39a87 ("drivers: provide
devm_platform_get_and_ioremap_resource()"), convert
platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230328061031.70140-2-yang.lee@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to commit 890cc39a87 ("drivers: provide
devm_platform_get_and_ioremap_resource()"), convert
platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230328061031.70140-1-yang.lee@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to commit 890cc39a87 ("drivers: provide
devm_platform_get_and_ioremap_resource()"), convert
platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230328061839.82185-1-yang.lee@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to commit 890cc39a87 ("drivers: provide
devm_platform_get_and_ioremap_resource()"), convert
platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230328062600.93160-1-yang.lee@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When using gpio based chip select the cs value can go outside the range
0 – 3. The various MX51_ECSPI_* macros did not take this into consideration
resulting in possible corruption of the configuration.
For example for any cs value over 3 the SCLKPHA bits would not be set and
other values in the register possibly corrupted.
One way to fix this is to just mask the cs bits to 2 bits. This still
allows all 4 native chip selects to work as well as gpio chip selects
(which can use any of the 4 chip select configurations).
Signed-off-by: Kevin Groeneveld <kgroeneveld@lenbrook.com>
Link: https://lore.kernel.org/r/20230318222132.3373-1-kgroeneveld@lenbrook.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Returning early in a platform driver's remove callback is wrong. In this
case the dma resources are not released in the error path. this is never
retried later and so this is a permanent leak. To fix this, only skip
hardware disabling if waking the device fails.
Fixes: 64ff247a97 ("spi: Add Qualcomm QUP SPI controller support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230330210341.2459548-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel Meteor Lake-S has the same SPI serial flash controller as Meteor
Lake-P. Add Meteor Lake-S PCI ID to the driver list of supported
devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20230331052812.39983-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Convert this driver from always returning zero in the remove callback to
the void returning variant.
Now that bcm2835_spi_remove returns no error code any more,
bcm2835_spi_shutdown() does the same thing as bcm2835_spi_remove(). So
drop the shutdown function and use bcm2835_spi_remove() as .shutdown
callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230330211022.2460233-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_ioremap_resource(), as this is exactly what this
function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20230329062450.58924-1-yang.lee@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to commit 890cc39a87 ("drivers: provide
devm_platform_get_and_ioremap_resource()"), convert
platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230328061524.77529-1-yang.lee@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It's fairly common practice for drivers to switch to a "sleep" pinctrl
state at the end of its runtime_suspend function and then back to
"default" at the beginning of runtime_resume. Let's do that for
spi-qcom-qspi.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230323102605.5.I79544b9486033bd7b27f2be55adda6d36f62a366@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
