Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner. While we are at it also remove the
regcache_cache_only() calls from suspend/resume as there shouldn't be any IO
between suspend and resume.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_OFF at the end of CODEC probe()
can also be removed as the CODEC is already in OFF state at this point.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner. While we are at it also remove the
regcache_cache_only() calls from suspend/resume as there shouldn't be any IO
between suspend and resume.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASoC core now takes care of setting the bias level to SND_SOC_BIAS_OFF
when removing the CODEC, no need to do it manually anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We do a bit more than just running the callbacks during suspend and resume
these days (e.g. call regcache_mark_dirty() during suspend). But this is
only when suspend and resume callbacks are specified for the driver,
otherwise nothing is done. This means that drivers which don't want to do
anything special during suspend and resume, but still want the standard
operations to run, need to provide empty suspend and resume callback
functions (rather than no callbacks). This patch updates the suspend and
resume code to always run standard sequence regardless of whether suspend
and resume handlers are provided.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a substantial amount of drivers that in go to SND_SOC_BIAS_OFF on
suspend and go back to SND_SOC_BIAS_SUSPEND on resume (Often this is even
the only thing done in the suspend and resume handlers). This patch
introduces a new suspend_bias_off flag, which when set by a driver will let
the ASoC core automatically put the device's DAPM context at the
SND_SOC_BIAS_OFF level during suspend. Once the device is resumed the DAPM
context will go back to SND_SOC_BIAS_STANDBY (if the context is idle,
otherwise to SND_SOC_BIAS_ON).
This will allow us to remove a fair bit of duplicated code from the drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently when a ASoC sound card is unregistered we leave the individual
components in their current state, just call the remove() callback and leave
it to the drivers to do the proper shutdown/cleanup.
This patch introduces a call to snd_soc_dapm_shutdown() when removing the
card. This will make sure that all DAPM widgets are properly powered down
and all DAPM contexts are put at the SND_SOC_BIAS_OFF level. This will
ensure that all components are properly powered down when the card is
removed.
Since a lot of drivers manually go to SND_SOC_BIAS_OFF in their remove
callback this will also allow us to remove a bit of duplicated code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set card->instantiated to false when the card is removed to make sure that
operations that expect the card to be fully instantiated do not run anymore
during card removal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASoC core will only call the suspend/resume callbacks when the device's
DAPM context is idle. Since this driver sets idle_bias_off to true this
means that the device is already in SND_SOC_BIAS_OFF when the suspend
callback is called, so there is no need to manually set this state again.
There is also no need to go to SND_SOC_BIAS_STANDBY in the resume callback
since the core will go right back to SND_SOC_BIAS_OFF.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASoC core will only call the suspend/resume callbacks when the device's
DAPM context is idle. Since this driver sets idle_bias_off to true this
means that the device is already in SND_SOC_BIAS_OFF when the suspend
callback is called, so there is no need to manually set this state again.
There is also no need to go to SND_SOC_BIAS_STANDBY in the resume callback
since the core will go right back to SND_SOC_BIAS_OFF.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASoC core will only call the suspend/resume callbacks when the device's
DAPM context is idle. Since this driver sets idle_bias_off to true this
means that the device is already in SND_SOC_BIAS_OFF when the suspend
callback is called, so there is no need to manually set this state again.
There is also no need to go to SND_SOC_BIAS_STANDBY in the resume callback
since the core will go right back to SND_SOC_BIAS_OFF.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASoC core will only call the suspend/resume callbacks when the device's
DAPM context is idle. Since this driver sets idle_bias_off to true this
means that the device is already in SND_SOC_BIAS_OFF when the suspend
callback is called, so there is no need to manually set this state again.
There is also no need to go to SND_SOC_BIAS_STANDBY in the resume callback
since the core will go right back to SND_SOC_BIAS_OFF.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASoC core will only call the suspend/resume callbacks when the device's
DAPM context is idle. Since this driver sets idle_bias_off to true this
means that the device is already in SND_SOC_BIAS_OFF when the suspend
callback is called, so there is no need to manually set this state again.
There is also no need to go to SND_SOC_BIAS_STANDBY in the resume callback
since the core will go right back to SND_SOC_BIAS_OFF.
Also drop the regcache_cache_only() calls from the suspend and resume
handlers. There shouldn't be any IO happening after suspend and before
resume.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are no real users for cache_only in "struct snd_soc_codec" so remove
it and needless debugfs node.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This was accidentally lost in commit f1d45cc3ae ("ASoC: Consolidate
platform and CODEC probe/remove").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
With componentization we no longer necessarily need a snd_soc_codec struct for a
card. Instead of checking if the card's CODEC list is empty just use
card->instantiated to check if the card has been instantiated yet.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There were never any actual users of this in upstream and by we have with
regmap a replacement in place, which should be used by new drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
So far regmap is only automatically initialized for CODECs. Now that we have the
infrastructure in place to let components have DAPM widgets and controls that
want to use the generic regmap based IO also make sure to automatically
initialize regmap for all components.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The lookup of CPU and CODEC DAIs is fairly similar and can easily be
consolidated into a single helper function.
There are two main differences in the current implementation of the CPU and
CODEC DAI lookup:
1) CPU DAIs can be looked up by the DAI name alone and do not necessarily
require a component name/of_node.
2) The CODEC DAI search only considers DAIs from CODEC components.
For 1) the new helper function will allow to lookup DAIs without providing a
component name or of_node, but since snd_soc_register_card() already rejects
CODEC DAI link components without neither a of_node or a name we'll never get
into the situation where we try to lookup a CODEC DAI without a name/of_node.
For 2) the new helper function just always considers all components.
Componentization is now at a point where it is possible to register a CODEC as a
snd_soc_component rather than a snd_soc_codec, by considering DAIs from all
components it is possible to use such a CODEC in a DAI link.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
CPU and CODEC DAI works exactly the same way. There is already a helper function
for CODEC DAI removal, use that one as well for CPU DAI removal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently when a DAI has no CODEC associated to it the reference on the module
containing the DAI driver is increased when the DAI is probed and decrease when
the DAI is removed. For DAIs with CODECs the module reference count was already
incremented when the CODEC is probed. Now that all components have their module
reference count incremented when they are probed and all DAIs do have a
component it is possible to remove the module reference counting on DAI probe
and removal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Having the check in a centralized place makes the code a bit cleaner and
shorter.
Note: There is a slight semantic change in this patch. soc_probe_aux_dev() will
no longer return -EBUSY if the AUX dev has already been probed before. This is
fine though since it will simply do nothing in that case and return success.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Given that the component is the containing structure it makes more sense to pass
the component rather than the DAPM context to the AUX dev init callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch makes it possible to register arbitrary components as a AUX dev
for a card. This was previously only possible for CODEC components. With
componentization having made it possible for components to have DAPM contexts
and controls there is no reason why AUX devs should be artificially limited to
snd_soc_codec devices.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that we have a unified probe and remove path make sure to call them for all
components. soc_{probe,remove}_component are responsible for setting up the DAPM
context for the component, initialize the component prefix, manage the debugfs
entries as well as do the registration of table based controls and DAPM
elements. They also call the component drivers probe and remove callbacks. This
patch makes these things available for generic snd_soc_component drivers rather
than only having them for snd_soc_codec and snd_soc_platform drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are some place in the ASoC core that expect rtd->codec to be non NULL
(mainly CODEC specific sysfs files). With componentization going forward
rtd->codec might be NULL in some cases. This patch prepares the core for this by
not registering CODEC specific sysfs files if rtd->codec is NULL. sysfs file
removal does not need to be conditionalized as it handles the removal of
non-existing files just fine.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The platform and CODEC probe and remove code is now largely identical. This
patch consolidates it at the component level.
The resulting code is slightly larger due to all the boiler plate code setting
up the indirection for the table based control and DAPM registration. Once all
drivers have been update to no longer use the snd_soc_codec_driver and
snd_soc_platform_driver specific fields for this the indirection can be removed
again.
This patch contains two noteworthy hacks that are only meant to be temporary to
be able to update drivers and the core in separate incremental patches.
The first hack is related to that some DPCM platforms expect that the DAPM
widgets for the DAIs of a snd_soc_component are created in the DAPM context of
the snd_soc_platform that has the same parent device. For handling this the
steal_sibling_dai_widgets attribute is introduced. It gets set for
snd_soc_platforms that register DAPM elements. When creating the DAI widgets for
a component this flag is checked and if it is found on one of the siblings the
component will not create any DAI widgets in its own DAPM context. If the
attribute is set on a platform it will look for siblings components and create
DAI widgets for them in its own context. The fix for this will be to update
the offending drivers to only register a single component rather than two.
The second hack deals with the fact that the ASoC card suspend and resume code
still needs a list of CODECs that have been registered for the card. To handle
this the generic probe and remove path have a check to see if the component is
CODEC and if yes add/remove it to the card's CODEC list. While it is possible to
clean up the suspend/resume code to not need the CODEC list anymore this is a
bit of a chicken and egg problem since it will become easier to clean up the
suspend/resume code once there is a unified component layer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The debugfs registration is mostly identical between platforms and CODECs. This
patches consolidates the two implementations at the component level.
Unfortunately there are still a couple of CODEC specific debugfs files that are
related to legacy ASoC IO that need to be registered. For this a new callback is
added to the component struct that will be initialized when a CODEC is
registered and will be used to register the CODEC specific files. Once there are
no drivers left using legacy IO this can be removed again.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a codec driver for the Everest ES8328. It supports two separate audio
outputs and two separate audio inputs.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Here is the additional fix patches that have been queued up since the
previous pull request. A few HD-audio fixes, a USB-audio quirk
addition, and a couple of trivial cleanup for the legacy OSS codes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJT7hqWAAoJEGwxgFQ9KSmk5T8P/3aWFguhkpcK9PKCYB+93XAD
04f+fyRXEGHiU6+bvEy3NhC3cRp9++cQteRrzFfFLKoT2zCEKwP3fCJhuls7YWpg
CQUa4ojjqJ0E7dMcCHDxY6efFaDQKwmvu7j4VURegv97O5c7mcosxdMzI+FF5Osf
r/LbOjrpUNMFCFFKdRdU+Y0Msm+BspVt9FqI7Q7ge0GRQprtL21QcnOO2CGQ27lW
UOvRRqUuS5ePAbqlXH0o39awPqEvScK+dWmMKEvamLCbwKp8dPtlClfch4B5qofx
ZdS3nPEyayc10gl49k12qfJop6v2GrVfx/uwW0L6b+yELAmoX4dLBku2Zuw2XL/E
roRA5ZXf4Z0tQVxdYvCTlMlsTDB6WOD9icBoOvSdpnyCT67PGxeTWDzOcTXjZtbv
d+tLC+QpeH3RWzcHPe7PQEe8TOql2uRLwj2MSbzVT45MJdWIY45KoBtzoy15YPIm
RVPgSdNpomQXOFx+MFv4OjljaI2xeMZadf4pSTV52U1Kkaf+AvAKT0hS7p+dFtUo
pb1NLKBSj996Ayub211thziISTwzNQpCWrqLqafHpt7XDkNEjygJPNV9Q0j6fmbd
O+XWw2OiHSbh/SPzRrAoIE0sH2+45+BZcrkwMHD1QMFYyYQ+y1Rpdy0UKPnKKO0c
Oj4W21IY0I19gtq1jBAa
=UPFy
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here is the additional fix patches that have been queued up since the
previous pull request. A few HD-audio fixes, a USB-audio quirk
addition, and a couple of trivial cleanup for the legacy OSS codes"
* tag 'sound-fix-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Set TLV_DB_SCALE_MUTE bit for cx5051 vmaster
ALSA: hda/ca0132 - Don't try loading firmware at resume when already failed
ALSA: hda - Fix pop noises on reboot for Dell XPS 13 9333
ALSA: hda - Set internal mic as default input source on Dell XPS 13 9333
ALSA: usb-audio: fix BOSS ME-25 MIDI regression
ALSA: hda - Fix parsing of CMI8888 codec
ALSA: hda - Fix probing and stuttering on CMI8888 HD-audio controller
ALSA: hda/realtek - Fixed ALC286/ALC288 recording delay for Headset Mic
sound: oss: Remove typedefs wanc_info and wavnc_port_info
sound: oss: uart401: Remove typedef uart401_devc
Miscellaneous
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jJGu
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
window:
Group changes to the device tree. In preparation for adding device tree
overlay support, OF_DYNAMIC is reworked so that a set of device tree
changes can be prepared and applied to the tree all at once. OF_RECONFIG
notifiers see the most significant change here so that users always get
a consistent view of the tree. Notifiers generation is moved from before
a change to after it, and notifiers for a group of changes are emitted
after the entire block of changes have been applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART devices
get this support automatically when uart_add_one_port() is called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then unloaded
again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory setup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8IFz
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree updates from Grant Likely:
"The branch contains the following device tree changes the v3.17 merge
window:
Group changes to the device tree. In preparation for adding device
tree overlay support, OF_DYNAMIC is reworked so that a set of device
tree changes can be prepared and applied to the tree all at once.
OF_RECONFIG notifiers see the most significant change here so that
users always get a consistent view of the tree. Notifiers generation
is moved from before a change to after it, and notifiers for a group
of changes are emitted after the entire block of changes have been
applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART
devices get this support automatically when uart_add_one_port() is
called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then
unloaded again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory
setup"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux: (21 commits)
of: Fixing OF Selftest build error
drivers: of: add automated assignment of reserved regions to client devices
of: Use proper types for checking memory overflow
of: typo fix in __of_prop_dup()
Adding selftest testdata dynamically into live tree
of: Add todo tasklist for Devicetree
of: Transactional DT support.
of: Reorder device tree changes and notifiers
of: Move dynamic node fixups out of powerpc and into common code
of: Make sure attached nodes don't carry along extra children
of: Make devicetree sysfs update functions consistent.
of: Create unlocked versions of node and property add/remove functions
OF: Utility helper functions for dynamic nodes
of: Move CONFIG_OF_DYNAMIC code into a separate file
of: rename of_aliases_mutex to just of_mutex
of/platform: Fix of_platform_device_destroy iteration of devices
of: Migrate of_find_node_by_name() users to for_each_node_by_name()
tty: Update hypervisor tty drivers to use core stdout parsing code.
arm/versatile: Add the uart as the stdout device.
of: Enable console on serial ports specified by /chosen/stdout-path
...
Conexnat HD-audio driver has a workaround for cx5051 (aka CX20561)
chip to add fake mute controls to each amp (commit 3868137e). This
implies the minimum-as-mute TLV bit in TLV for each corresponding
control. Meanwhile we build the virtual master from these, but the
TLV bit is missing, even though the slaves have it.
This patch simply adds the missing TLV_DB_SCALE_MUTE bit for vmaster,
as already done in patch_sigmatel.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CA0132 driver tries to reload the firmware at resume. Usually this
works since the firmware loader core caches the firmware contents by
itself. However, if the driver failed to load the firmwares
(e.g. missing files), reloading the firmware at resume goes through
the actual file loading code path, and triggers a kernel WARNING like:
WARNING: CPU: 10 PID:11371 at drivers/base/firmware_class.c:1105 _request_firmware+0x9ab/0x9d0()
For avoiding this situation, this patch makes CA0132 skipping the f/w
loading at resume when it failed at probe time.
Reported-and-tested-by: Janek Kozicki <cosurgi@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If nid 0x15 (Headphone Playback Switch) is in D3 and headphones are
plugged in when the laptop reboots, a pop noise is generated.
Prevent this by keeping nid 0x15 in D0 when headphones are plugged in.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=76611
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the laptop is powered on with a jack plugged in, independently on what
is plugged, the jack is treated as a microphone jack.
Initialize the capture source so that by default jacks are treated as
headphones jacks. This will also prevent pop noises on boot in case
headphones are plugged in since setting/unsetting mic-in as input source
causes a pop noise.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=76611
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The BOSS ME-25 turns out not to have any useful descriptors in its MIDI
interface, so its needs a quirk entry after all.
Reported-and-tested-by: Kees van Veen <kees.vanveen@gmail.com>
Fixes: 8e5ced83dd ("ALSA: usb-audio: remove superfluous Roland quirks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJT5DYPAAoJEIwa5zzehBx37egQAIiatNiLLqZnfo3rwGADRz/a
POfPovktj68aPcobyzoyhFtToMqGvi9PpysyFTIQD2HJFG+5BtiIAuqtg0875zDe
EpBWgsfugrm0YktJWAtUerj60oAmNPbKfaEm1cOOWuM2lb2mV+QkRrwSTAgsqkT7
927BzMXKKBRPOVLL0RYhoF8EXa0Eg8kCqAHP8fJrzVYkRp+UrZJDnGiUP1XmWJN+
VXQMu5SEjcPMtqT7+tfX455RfREHJfBcJ1ZN/dPF8HMWDwClQG0lyc6hifh1MxwO
8DjIZNkfZeKqgDqVyC17re7pc7p8md5HL8WXbrKpK0A9vQ5bRexbPHxcwJ1T/C2Y
465H+st5XXbuzV1gbMwjK1/ycsH0tCyffckk8Yl/2e1Fs7GgPNbAELtTdl+5vV1Y
xmDXkyo/9WlRM3LQ23IGKwW7VzN86EfWVuShssfro0fO7xDdb4OOYLdQI+4bCG+h
ytQYun1vU32OEyNik5RVNQuZaMrv2c93a3bID4owwuPHPmYOPVUQaqnRX/0E51eA
aHZYbk2GlUOV3Kq5aSS4iyLg1Yj+I9/NeH9U+A4nc+PQ5FlgGToaVSCuYuw4DqbP
AAG+sqQHbkBMvDPobQz/yd1qZbAb4eLhGy11XK1t5S65rApWI55GwNXnvbyxqt8x
wpmxJTASGxcfuZZgKXm7
=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
- Checkpatch fixes throughout the subsystem
- Use Regmap to handle IRQs in max77686, extcon-max77693 and mc13xxx-core
- Use DMA in rtsx_pcr
- Restrict building on unsupported architectures on timberdale, cs5535
- SPI hardening in cros_ec_spi
- More robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- Reorder PM runtime and regulator handing during shutdown in arizona
- Enable wakeup in cros_ec_spi
- Unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- Add regulator handing into suspend() in sec-core
- Remove pointless wrapper functions in extcon-max77693 and i2c-cros-ec-tunnel
- Use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- Device Tree documentation updates throughout
- Provide power management support in max77686
- Few OF clean-ups in max77686
- Use manged resources in tps6105x
== New drivers/supported devices ==
- Add support for s2mpu02 to sec-core
- Add support for Allwinner A32 to sun6i-prcm
- Add support for Maxim 77802 in max77686
- Add support for DA9063 AD in da9063
- Add new driver for Intel PMICs (generic) and specifically Crystal Cove
== (Re-)moved drivers ==
- Move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cNI
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD update from Lee Jones:
"Changes to existing drivers:
- checkpatch fixes throughout the subsystem
- use Regmap to handle IRQs in max77686, extcon-max77693 and
mc13xxx-core
- use DMA in rtsx_pcr
- restrict building on unsupported architectures on timberdale,
cs5535
- SPI hardening in cros_ec_spi
- more robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- reorder PM runtime and regulator handing during shutdown in arizona
- enable wakeup in cros_ec_spi
- unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- add regulator handing into suspend() in sec-core
- remove pointless wrapper functions in extcon-max77693 and
i2c-cros-ec-tunnel
- use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- devicetree documentation updates throughout
- provide power management support in max77686
- few OF clean-ups in max77686
- use manged resources in tps6105x
New drivers/supported devices:
- add support for s2mpu02 to sec-core
- add support for Allwinner A32 to sun6i-prcm
- add support for Maxim 77802 in max77686
- add support for DA9063 AD in da9063
- new driver for Intel PMICs (generic) and specifically Crystal Cove
(Re-)moved drivers ==
- move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb"
* tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (101 commits)
MAINTAINERS: Update MFD repo location
mfd: omap-usb-host: Fix improper mask use.
mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
mfd: arizona: Add missing handling for ISRC3 under/overclocked
mfd: wm5110: Add new interrupt register definitions
mfd: arizona: Rename thermal shutdown interrupt
mfd: wm5110: Add in the output done interrupts
mfd: wm5110: Remove non-existant interrupts
mfd: tps65912-spi: Remove unused variable
mfd: htc-i2cpld: Remove unused code
mfd: da9063: Add support for AD silicon variant
mfd: arizona: Map MICVDD from extcon device to the Arizona core
mfd: arizona: Add MICVDD to mapped regulators for wm8997
mfd: max77686: Ensure device type IDs are architecture agnostic
mfd: max77686: Add Maxim 77802 PMIC support
mfd: tps6105x: Use managed resources when allocating memory
mfd: wm8997-tables: Suppress 'line over 80 chars' warnings
mfd: kempld-core: Correct a variety of checkpatch warnings
mfd: ipaq-micro: Fix coding style errors/warnings reported by checkpatch
mfd: si476x-cmd: Remedy checkpatch style complains
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 3.17. It contains:
- misc Cavium Octeon, BCM47xx, BCM63xx and Alchemy updates
- MIPS ptrace updates and cleanups
- various fixes that will also go to -stable
- a number of cleanups and small non-critical fixes.
- NUMA support for the Loongson 3.
- more support for MSA
- support for MAAR
- various FP enhancements and fixes"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
MIPS: jz4740: remove unnecessary null test before debugfs_remove
MIPS: Octeon: remove unnecessary null test before debugfs_remove_recursive
MIPS: ZBOOT: implement stack protector in compressed boot phase
MIPS: mipsreg: remove duplicate MIPS_CONF4_FTLBSETS_SHIFT
MIPS: Bonito64: remove a duplicate define
MIPS: Malta: initialise MAARs
MIPS: Initialise MAARs
MIPS: detect presence of MAARs
MIPS: define MAAR register accessors & bits
MIPS: mark MSA experimental
MIPS: Don't build MSA support unless it can be used
MIPS: consistently clear MSA flags when starting & copying threads
MIPS: 16 byte align MSA vector context
MIPS: disable preemption whilst initialising MSA
MIPS: ensure MSA gets disabled during boot
MIPS: fix read_msa_* & write_msa_* functions on non-MSA toolchains
MIPS: fix MSA context for tasks which don't use FP first
MIPS: init upper 64b of vector registers when MSA is first used
MIPS: save/disable MSA in lose_fpu
MIPS: preserve scalar FP CSR when switching vector context
...
CMI8888 codec chip has a boost amp (only) on the headphone pin, and
this confuses the generic parser, which tends to pick up the most
outside amp. This results in the wrong volume setup, as the driver
complains like:
hda_codec: Mismatching dB step for vmaster slave (-100!=1000)
For avoiding this problem, rule out the amp on NID 0x10 and create
"Headphone Amp" volume control manually instead.
Note that this patch still doesn't fix all problems yet. The sound
output from the line out seems still too low. It will be fixed in
another patch (hopefully).
Reported-and-tested-by: Vincent Lejeune <vljn@ovi.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS Phoebus with CMI8888 HD-audio chip (PCI id 13f6:5011) doesn't
work with HD-audio driver as is because of some weird nature. For
making DMA properly working, we need to disable MSI. The position
report buffer doesn't work, thus we need to force reading LPIB
instead. And yet, the codec CORB/RIRB communication gives errors
unless we disable the snooping (caching).
In this patch, all these workarounds are added as a quirk for the
device. The HD-audio *codec* chip needs yet another workaround, but
it'll be provided in the succeeding patch.
Reported-and-tested-by: Vincent Lejeune <vljn@ovi.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It will be recording voice delay for resume back recording for Headset Mic.
This alc286 will quickly open Headset Mic, to prevent avoid recording files are missing.
The issue was fixed. This is follow ALC286 programing guide.
[fix build error, add static and renamed the function by tiwai]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
