This is only needed for drivers that do not use vb2_fop_release().
Note that vb2_queue_release() is *not* the counterpart of vb2_queue_init()
as some drivers here seem to think.
Also use vb2_video_unregister_device() to automatically stop streaming
at unregister time for those drivers that set vdev->queue.
Note that sun4i-csi didn't unregister the video device at all. That's
now fixed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Video engine in AST2600 has the exactly same register set with
AST2500 except VR084 register which provides more precise JPEG
size read back. This commit adds support for the difference and
adds 'aspeed,ast2600-video-engine' compatible OF string.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'GRABBER' is a weird name, all other types map to the /dev
device names. Rename to 'VIDEO' to be consistent with the
other types.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the preferred form for GPL2+, and add IBM and Intel as the authors.
The driver was initially upstreamed by Eddie from IBM, and has had major
contributions from Jae at Intel.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The aspeed video IP has some differences between SoC families. Currently
the driver decides which registers to use at compile time, which means
a single kernel can not be used between platforms.
Switch to using runtime configuration of the registers that vary between
SoC families. This is in preparation for upcoming ast2600 support.
[hverkuil: replace ;; by ;]
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the recently introduced function devm_platform_ioremap_resource to
save a few lines of code. This makes the driver match common platform
device probe patterns.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In the implementation of aspeed_video_probe() the allocated memory for
video should be released if either devm_ioremap_resource()
or aspeed_video_init() or aspeed_video_setup_video() fails. Replace
kzalloc() with devm_kzalloc to avoid explicit release for video.
Fixes: d2b4387f3b ("media: platform: Add Aspeed Video Engine driver")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Sometimes it detects a weird resolution such as 1024x287 when the
actual resolution is 1024x768. To resolve such an issue, this
commit adds clearing for hsync and vsync polarity register bits
at the beginning of the first mode detection. This is recommended
in the datasheet.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To prevent inaccurate detections of resolution, this commit enables
clearing of hsync/vsync polarity bits based on probed sync state.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
While this might not occur in practice, if the device is doing
the right thing, it would be teoretically be possible to have
both hsync_counter and vsync_counter negatives.
If this ever happen, ctrl will be undefined, but the driver
will still call:
aspeed_video_update(video, VE_CTRL, 0, ctrl);
Change the code to prevent this to happen.
This was warned by cppcheck:
[drivers/media/platform/aspeed-video.c:653]: (error) Uninitialized variable: ctrl
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It returns '0' even when a failure happens on jpeg buffer allocation
so this commit fixes the issue.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
AST2500 silicon revision A1 and A2 have a silicon bug which causes
extremly long capturing time on specific resolutions (1680 width).
To fix the bug, this commit adjusts the capturing window register
setting to 1728 if detected width is 1680. The compression window
register setting will be kept as the original width so output
result will be the same.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case of watchdog timeout detected while doing mode detection,
it's better triggering video engine hardware reset immediately so
this commit fixes code for the case. Other than the case, it will
trigger video engine hardware reset after RESOLUTION_CHANGE_DELAY.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are cases that interrupt bits are cleared by a 500ms delayed
work which causes unnecessary irq calls. Also, the current
interrupt handler returns IRQ_HANDLED always but it should return
IRQ_NONE if there is any unhandled interrupt. So this commit
refines the interrupt handling logic to fix these issues.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
VE_INTERRUPT_CAPTURE_COMPLETE and VE_INTERRUPT_COMP_COMPLETE are
not set at the same time but the current interrupt handling
mechanism of this driver doesn't clear the interrupt flag until
both two are set, and this behavior causes unnecessary interrupt
handler calls. In fact, this driver provides JPEG format only so
taking care of the VE_INTERRUPT_COMP_COMPLETE is enough for getting
compressed image frame so this commit gets rid of the
VE_INTERRUPT_CAPTURE_COMPLETE checking logic to simplify the logic.
Handling of VE_INTERRUPT_CAPTURE_COMPLETE could be added back later
when it's actually needed.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, this driver prints out too much log messages when a
mode change happens, video turned off by screen saver and etc.
Actually, all cases are reported to user space properly. Also,
these are not critical errors but recoverable things, so this
commit changes the log level of some noisy printing outs.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Video Engine has a dedicated interrupt line so this driver doesn't
need to use IRQF_SHARED flag so remove it. Also, it'd be good for
following what Thomas recommended in the IRQF_ONESHOT support
patch like below:
"Note that for now IRQF_ONESHOT cannot be used with IRQF_SHARED to
avoid complex accounting mechanisms."
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Differently from other Aspeed drivers, this driver calls clock
control APIs in interrupt context. Since ECLK is coupled with a
reset bit in clk-aspeed module, aspeed_clk_enable will make 10ms of
busy waiting delay for triggering the reset and it will eventually
disturb other drivers' interrupt handling. To fix this issue, this
commit changes this driver's irq to threaded irq so that the delay
can be happened in a thread context.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, this driver calls clk_prepare and clk_unprepare from
interrupt context too but these should be called from sleepable
context only. To fix this issue, this commit splits out
clk_enable/disable and clk_prepare/unprepare, and it places
clk_prepare/unprepare calls into the module probe/remove function.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reserved memory doesn't need to be required; system memory would work
fine.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The reset line is toggled by enabling the clocks, so it's not necessary
to manually toggle the reset as well.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver allocates the spinlock but not initialize it.
Use spin_lock_init() on it to initialize it correctly.
This is detected by Coccinelle semantic patch.
Fixes: d2b4387f3b ("media: platform: Add Aspeed Video Engine driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Video Engine (VE) embedded in the Aspeed AST2400 and AST2500 SOCs
can capture and compress video data from digital or analog sources. With
the Aspeed chip acting a service processor, the Video Engine can capture
the host processor graphics output.
Add a V4L2 driver to capture video data and compress it to JPEG images.
Make the video frames available through the V4L2 streaming interface.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
