It will be set once corresponding set_feature command comes.
True if device is allowed to wake-up host by remote-wakeup
signalling.
This is preparation for remote wake-up support implementation,
it will not be implemented until gadget stack provide interface
for bringing remote wake-up signalling.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add parameter remote_wakeup to dwc2_restore_device_registers()
to be able to restore device registers according to programming
guide for dwc-otg. It says that in case of rem_wakeup DCTL must not
be restored here.
Remove setting of DCTL_PWRONPRGDONE from this function, because it
will be done in function responsible for exiting from hibernation.
WA for enabled EPx's IN and OUT in DDMA mode. On entering to
hibernation wrong value read and saved from DIEPDMAx,
as result BNA interrupt asserted on hibernation exit
by restoring from saved area.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Moved dtxfsiz from dwc2_gregs_backup to dwc2_dregs_backup,
because it is device register.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No-op change, only rename.
This code was misnamed originally. It was only responsible for partial
power down and not for hibernation.
Rename core_params->hibernation to core_params->power_down,
dwc2_set_param_hibernation() to dwc2_set_param_power_down().
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set 'lpm_capable' flag in the gadget structure so
indicating that LPM is supported.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added core state checking in dwc2_hsotg_ep_queue() function
to make sure that application will submit requests only in L0 state.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Configure core in device mode to support LPM according to
programming guide.
Device will start giving valid responses for LPM tokens.
After this patch device side LPM will start working.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added function for supporting Active Clock Gating functionality
in the driver.
PCGCCTL1 (Power and Clock Control) register will be used
for controlling the core`s active clock gating feature, and
the previously reserved 12th bit in GHWCFG4 now indicates that the
controller supports the Dynamic Power Reduction (Active Clock Gating)
during no traffic scenarios such as L0, idle, resume and suspend
states.
dwc2_enable_acg() function sets GATEEN bit in PCGCCTL1 register
and enables ACG, if it supported.
According to ACG functional specification, enabling of ACG feature
in host mode done in host initialization, before turning Vbus on,
specifically in dwc2_core_host_init function.
Enabling of ACG feature in device mode done in device initialization,
before clearing the SftDiscon bit in DCTL.
This bit was cleared in dwc2_hsotg_core_connect() function.So
dwc2_enable_acg() called before dwc2_core_connect() calls.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Renamed __orr32 and __bic32 function names to more descriptive
dwc2_set_bit and dwc2_clear_bit respectively.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabled only unmasked endpoints based on DAINTMSK register.
This will allow to minimize GINTSTS_GOUTNAKEFF interrupt handling.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In 'for' loop skipped masked and non-ISOC EPs. Also breaked 'for' loop
after setting SGOUTNAK in DCTL,when one enabled EP was detected.
This will allow to minimize incomplete ISOC OUT interrupt handling.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabled only that ISOC endpoints,for which interrupt bit was set
in the DAINTMSK register. This will allow to minimize incomplete
ISOC IN interrupt handling.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In dwc2_hsotg_core_init_disconnected() function used AHB burst size
parameter, instead of calculating already calculated value.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move dwc2_hsotg_wait_bit_set function to core.c so it can be used
anywhere in the code.
Added dwc2_hsotg_wait_bit_clear function in core.c.
Replace all the parts of register bit polling code with
dwc2_hsotg_wait_bit_set or dwc2_hsotg_wait_bit_clear functions
calls depends on code logic.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The irq is available in hsotg already, so there's no need to pass it as
separate function parameter.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We should call dwc2_hsotg_enqueue_setup() after properly
setting lx_state. Because it may cause error-out from
dwc2_hsotg_enqueue_setup() due to wrong value in lx_state.
Issue can be reproduced by loading driver while connected
A-Connector (start in A-HOST mode) then disconnect A-Connector
to switch to B-DEVICE.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
STSPHSERCVD (status phase received) interrupt should be
handled when EP0 is in DWC2_EP0_DATA_OUT state.
Sometimes STSPHSERCVD interrupt asserted , when EP0
is not in DATA_OUT state. Spurios interrupt.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In some cases device sending ZLP IN on non EP0 which
reassigning EP0 OUT descriptor pointer to that EP.
Dedicated for EP0 OUT descriptor multiple time re-used by
other EP while that descriptor already in use by EP0 OUT
for SETUP transaction. As result when SETUP packet received
BNA interrupt asserting.
In dwc2_hsotg_program_zlp() function dwc2_gadget_set_ep0_desc_chain()
must be called only for EP0.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In host mode reading from DPTXSIZn returning invalid value in
dwc2_check_param_tx_fifo_sizes function.
In total TxFIFO size calculations unnecessarily reducing by ep_info.
hw->total_fifo_size can be fully allocated for FIFO's.
Added num_dev_in_eps member in dwc2_hw_params structure to save number
of IN EPs.
Added g_tx_fifo_size array in dwc2_hw_params structure to store power
on reset values of DPTXSIZn registers in forced device mode.
Updated dwc2_hsotg_tx_fifo_count() function to get TxFIFO count from
num_dev_in_eps.
Updated dwc2_get_dev_hwparams() function to store DPTXFSIZn in
g_tx_fifo_size array.
dwc2_get_host/dev_hwparams() functions call moved after num_dev_in_eps
set from hwcfg4.
Modified dwc2_check_param_tx_fifo_sizes() function to check TxFIFOn
sizes based on g_tx_fifo_size array.
Removed ep_info subtraction during calculation of tx_addr_max in
dwc2_hsotg_tx_fifo_total_depth() function. Also removed
dwc2_hsotg_ep_info_size() function as no more need.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been noticed that the dwc2 udc state reporting doesn't
seem to work (at least on HiKey boards). Where after the initial
setup, the sysfs /sys/class/udc/f72c0000.usb/state file would
report "configured" no matter the state of the OTG port.
This patch adds a call so that we report to the UDC layer when
the gadget device is disconnected.
This patch does depend on the previous patch ("usb: dwc2:
Improve gadget state disconnection handling") in this patch set
in order to properly work.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Minas Harutyunyan <hminas@synopsys.com>
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We've found that while in host mode, using Android, if one runs
the command:
stop adbd
The existing usb devices being utilized in host mode are disconnected.
This is most visible with usb networking devices.
This seems to be due to adbd closing the file:
/dev/usb-ffs/adb/ep0
Which calls ffs_ep0_release() and the following backtrace:
[<ffffff800875a430>] dwc2_hsotg_ep_disable+0x148/0x150
[<ffffff800875a498>] dwc2_hsotg_udc_stop+0x60/0x110
[<ffffff8008787950>] usb_gadget_remove_driver+0x58/0x78
[<ffffff80087879e4>] usb_gadget_unregister_driver+0x74/0xe8
[<ffffff80087850c0>] unregister_gadget+0x28/0x58
[<ffffff800878511c>] unregister_gadget_item+0x2c/0x40
[<ffffff8008790ea8>] ffs_data_clear+0xe8/0xf8
[<ffffff8008790ed8>] ffs_data_reset+0x20/0x58
[<ffffff8008793218>] ffs_data_closed+0x98/0xe8
[<ffffff80087932d8>] ffs_ep0_release+0x20/0x30
Then when dwc2_hsotg_ep_disable() is called, we call
kill_all_requests() which causes a bunch of the following
messages:
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
init: Service 'adbd' (pid 1915) killed by signal 9
init: Sending signal 9 to service 'adbd' (pid 1915) process group...
init: Successfully killed process cgroup uid 0 pid 1915 in 0ms
init: processing action (init.svc.adbd=stopped) from (/init.usb.configfs.rc:15)
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 8 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 12 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 15 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 3 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 4 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_update_urb_state_abn(): trimming xfer length
And the usb devices connected are basically hung at this point.
It seems like if we're in host mode, we probably shouldn't run
the dwc2_hostg_ep_disable logic, so this patch returns an error
in that case.
With this patch (along with the previous patch in this set), we avoid
the mismatched interrupts and connected usb devices continue to function.
I'm not sure if some other solution would be better here, but this seems
to work, so I wanted to send it out for input on what the right approach
should be.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Minas Harutyunyan <hminas@synopsys.com>
Reported-by: YongQin Liu <yongqin.liu@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make the structure const as it is only stored in the ops field of a
usb_ep structure, which is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reseted DEVADDR field in DCFG to zero on USB RESET.
Device address in DCFG register does not reset to zero,
which required to pass enumeration, after disconnect and
reconnect.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here's the big pull request for the Gadget
API. Again the majority of changes sit in dwc2
driver. Most important changes contain a workaround
for GOTGCTL being wrong, a sleep-inside-spinlock fix
and the big series of cleanups on dwc2.
One important thing on dwc3 is that we don't anymore
need gadget drivers to cope with unaligned OUT
transfers for us. We have support for appending one
extra chained TRB to align transfer ourselves.
Apart from these, the usual set of typos,
non-critical fixes, etc.
-----BEGIN PGP SIGNATURE-----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=gk8j
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v4.11
Here's the big pull request for the Gadget
API. Again the majority of changes sit in dwc2
driver. Most important changes contain a workaround
for GOTGCTL being wrong, a sleep-inside-spinlock fix
and the big series of cleanups on dwc2.
One important thing on dwc3 is that we don't anymore
need gadget drivers to cope with unaligned OUT
transfers for us. We have support for appending one
extra chained TRB to align transfer ourselves.
Apart from these, the usual set of typos,
non-critical fixes, etc.
Remove legacy DWC2_G_P_LEGACY_TX_FIFO_SIZE array for TX FIFOs.
Update dwc2_set_param_tx_fifo_sizes function to calculate
and assign default average FIFO depth to each member of
g_tx_fifo_size array. Total FIFO size, EP Info block's size,
FIFO operation mode and device operation mode are taken into
consideration during the calculation.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Basically when plugging in various cables in different orders, I'm
occasionally seeing the following BUG splat:
[ 86.215403] BUG: scheduling while atomic: kworker/u16:2/53/0x00000002
[ 86.219164] usb 1-1: USB disconnect, device number 9
[ 86.226845] Preemption disabled at:[ 86.230218]
[<ffffff8008673558>] dwc2_conn_id_status_change+0x120/0x250
[ 86.236894] CPU: 0 PID: 53 Comm: kworker/u16:2 Tainted: G W
4.9.0-rc8-00051-gd5a7979-dirty #1702
[ 86.246836] Hardware name: HiKey Development Board (DT)
[ 86.252100] Workqueue: dwc2 dwc2_conn_id_status_change
[ 86.257279] Call trace:
[ 86.259771] [<ffffff8008087c28>] dump_backtrace+0x0/0x1a0
[ 86.265210] [<ffffff8008087ddc>] show_stack+0x14/0x20
[ 86.270308] [<ffffff80084343f0>] dump_stack+0x90/0xb0
[ 86.275401] [<ffffff80080d8d94>] __schedule_bug+0x6c/0xb8
[ 86.280841] [<ffffff8008a07220>] __schedule+0x4f8/0x5b0
[ 86.286099] [<ffffff8008a073e8>] schedule+0x38/0xa0
[ 86.291017] [<ffffff8008a0a6cc>] schedule_hrtimeout_range_clock+0x8c/0xf0
[ 86.297846] [<ffffff8008a0a740>] schedule_hrtimeout_range+0x10/0x18
[ 86.304150] [<ffffff8008a0a4a0>] usleep_range+0x50/0x58
[ 86.309418] [<ffffff800866d8dc>] dwc2_wait_for_mode.isra.4+0x54/0xd0
[ 86.315815] [<ffffff800866f058>] dwc2_core_reset+0xe0/0x168
[ 86.321431] [<ffffff800867e364>] dwc2_hsotg_core_init_disconnected+0x2c/0x310
[ 86.328602] [<ffffff8008673568>] dwc2_conn_id_status_change+0x130/0x250
[ 86.335254] [<ffffff80080ccd48>] process_one_work+0x118/0x370
[ 86.341035] [<ffffff80080ccfe8>] worker_thread+0x48/0x498
[ 86.346473] [<ffffff80080d2eb0>] kthread+0xd0/0xe8
[ 86.351299] [<ffffff8008082e80>] ret_from_fork+0x10/0x50
This seems to be caused by the dwc2_wait_for_mode() calling
usleep_range() while the hstog->lock spinlock is held, since
we take that before calling dwc2_hsotg_core_init_disconnected().
This patch avoids the issue by adding an extra argument to
dwc2_core_reset(), as suggested by John Youn, which allows us to
skip the waiting, which should be unnecessary when calling from
dwc2_hsotg_core_init_disconnected().
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check these parameters only for true or false. There is no need to check
for greater or less than 0.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add programming of GDFIFOCFG register in device mode.
It must contain start address for EP Info block and
total FIFO depth.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Take the sizeof '*req' instead of 'struct dwc2_hsotg_req'.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* Remove braces for one-line statements
* Add missing braces where another arm in if-statement uses braces
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix misaligned and over 80-character comments.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This commmit is the result of running checkpatch --fix.
The results were verified for correctness. Some of the fixes result in
line over 80 char which we will fix manually later.
The following is a summary of what was done by checkpatch:
* Remove externs on function prototypes.
* Replace symbolic permissions with octal.
* Align code to open parens.
* Replace 'unsigned' with 'unsigned int'.
* Remove unneccessary blank lines.
* Add blank lines after declarations.
* Add spaces around operators.
* Remove unnecessary spaces after casts.
* Replace 'x == NULL' with '!x'.
* Replace kzalloc() with kcalloc().
* Concatenate multi-line strings.
* Use the BIT() macro.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
USBTrdTim must be programmed to 0x5 when phy has a UTMI+ 16-bit wide
interface or 0x9 when it has a 8-bit wide interface.
GUSBCFG reset value (Value After Reset: 0x1400) sets USBTrdTim to 0x5.
In case of 8-bit UTMI+, without clearing GUSBCFG.USBTRDTIM mask, USBTrdTim
results in 0xD (0x5 | 0x9).
That's why we need to clear GUSBCFG.USBTRDTIM mask before setting USBTrdTim
value, to ensure USBTrdTim is correctly set in case of 8-bit UTMI+.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Remove DMA memory free from EP disable flow by replacing
dma_alloc_coherent with dmam_alloc_coherent.
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc2_hsotg_ep_enable can be called from interrupt context, so all
allocations should be done with GFP_ATOMIC flags. This fixes following
issue on ARM architecture:
[<c010d830>] (unwind_backtrace) from [<c010a51c>] (show_stack+0x10/0x14)
[<c010a51c>] (show_stack) from [<c032930c>] (dump_stack+0x74/0x94)
[<c032930c>] (dump_stack) from [<c011cd30>] (__warn+0xd4/0x100)
[<c011cd30>] (__warn) from [<c011cd7c>] (warn_slowpath_null+0x20/0x28)
[<c011cd7c>] (warn_slowpath_null) from [<c0187e04>] (smp_call_function_many+0xcc/0x2a4)
[<c0187e04>] (smp_call_function_many) from [<c0188014>] (on_each_cpu_mask+0x38/0xa8)
[<c0188014>] (on_each_cpu_mask) from [<c01ddfe0>] (start_isolate_page_range+0x134/0x1b8)
[<c01ddfe0>] (start_isolate_page_range) from [<c01a3c14>] (alloc_contig_range+0xac/0x2f8)
[<c01a3c14>] (alloc_contig_range) from [<c01de3e4>] (cma_alloc+0xe0/0x1a8)
[<c01de3e4>] (cma_alloc) from [<c0110acc>] (__alloc_from_contiguous+0x38/0xe0)
[<c0110acc>] (__alloc_from_contiguous) from [<c0110ba4>] (cma_allocator_alloc+0x30/0x38)
[<c0110ba4>] (cma_allocator_alloc) from [<c0111034>] (__dma_alloc+0x1c0/0x2c8)
[<c0111034>] (__dma_alloc) from [<c01111b4>] (arm_dma_alloc+0x3c/0x48)
[<c01111b4>] (arm_dma_alloc) from [<c04ad800>] (dwc2_hsotg_ep_enable+0xec/0x46c)
[<c04ad800>] (dwc2_hsotg_ep_enable) from [<c04da610>] (usb_ep_enable+0x2c/0x3c)
[<c04da610>] (usb_ep_enable) from [<c04dc0c0>] (ecm_set_alt+0xa8/0x154)
[<c04dc0c0>] (ecm_set_alt) from [<c04d678c>] (composite_setup+0xd74/0x1540)
[<c04d678c>] (composite_setup) from [<c04ae048>] (dwc2_hsotg_complete_setup+0xb8/0x370)
[<c04ae048>] (dwc2_hsotg_complete_setup) from [<c04d987c>] (usb_gadget_giveback_request+0xc/0x10)
[<c04d987c>] (usb_gadget_giveback_request) from [<c04acafc>] (dwc2_hsotg_complete_request+0x78/0x128)
[<c04acafc>] (dwc2_hsotg_complete_request) from [<c04aed28>] (dwc2_hsotg_epint+0x69c/0x81c)
[<c04aed28>] (dwc2_hsotg_epint) from [<c04af6c4>] (dwc2_hsotg_irq+0xfc/0x748)
[<c04af6c4>] (dwc2_hsotg_irq) from [<c0163264>] (__handle_irq_event_percpu+0x58/0x140)
[<c0163264>] (__handle_irq_event_percpu) from [<c0163368>] (handle_irq_event_percpu+0x1c/0x58)
[<c0163368>] (handle_irq_event_percpu) from [<c01633dc>] (handle_irq_event+0x38/0x5c)
[<c01633dc>] (handle_irq_event) from [<c01666e4>] (handle_fasteoi_irq+0xc4/0x19c)
[<c01666e4>] (handle_fasteoi_irq) from [<c0162a2c>] (generic_handle_irq+0x18/0x28)
[<c0162a2c>] (generic_handle_irq) from [<c0162b40>] (__handle_domain_irq+0x6c/0xe4)
[<c0162b40>] (__handle_domain_irq) from [<c0101470>] (gic_handle_irq+0x50/0x9c)
[<c0101470>] (gic_handle_irq) from [<c010b00c>] (__irq_svc+0x6c/0xa8)
Fixes: 5f54c54b0b ("usb: dwc2: gadget: Add DDMA chain pointers to
dwc2_hsotg_ep structure")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Remove request length checking from dwc2_hsotg_unmap_dma() and
dwc2_hsotg_map_dma(). That checking is done in functions called from
those functions, usb_gadget_unmap_request_by_dev() and
usb_gadget_map_request_by_dev() respectively, so it's unnecessary.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
While sending zlp for DWC2_EP0_STATUS_IN EP direction was changed to IN.
Change it back to complete OUT transfer request.
This affects only on DMA mode, because DMA buffer map/unmap function is
direction sensitive.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check the request length in dwc2_hsotg_start_req() function. If
length == 0, do not write DMA address to control register.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added new core param for low speed, which can be used only when SNPSID
is equal to DWC2_CORE_FS_IOT. When LS mode is enabled, we are
restricting ep types and providing to upper layer only INTR and CTRL
endpoints.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When device is enumerated in LS we should program ep0_mps accordingly.
USB2 spec says that in LS mode, control ep mps must be 8.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Do modifications in dwc2_hsotg_core_init_disconnected() function to
enable USB 1.1 Full-Speed Serial Transceiver Select in GUSBCFG register
if corresponding speed and PHY types are chosen. Adjust device speed
selection in DCFG register as well.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check if endpoint is enabled during dwc2_hsotg_ep_disable() function
processing and call dwc2_hsotg_ep_stop_xfr() to disable it and flush
associated FIFO.
Move dwc2_hsotg_ep_stop_xfr() and dwc2_hsotg_wait_bit_set() functions
upper before dwc2_hsotg_ep_enable and dwc2_hsotg_ep_disable function
definitions.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Correct dwc2_hsotg_ep_stop_xfr() function to follow dwc2 programming
guide for setting NAK on specific endpoint, disabling it and flushing
corresponding FIFO.
Current code does not take into account whether core acts in shared or
dedicated FIFO mode, current endpoint is periodic or not. It does not
clear EPDISBLD interrupt after programming of DXEPCTL_EPDIS, does not
flush shared TX FIFO and tries to clear global out NAK in wrong manner
instead of setting DCTL_CGOUTNAK.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Tests with various hosts show that depend on time difference between
host sending SETUP packet and IN/OUT token SW could get Xfercomplete
interrupt without SetUp interrupt. On the other hand, SW should parse
received SETUP packet only after ensuring that Host has moved to either
Data or Status stage of control transfer.
For this purpose added checking in the dwc2_hsotg_epint() function to
not handle xfercomplete and postpone SETUP packet analysis till SW's
getting of setup phase done interrupt.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DDMA mode if programmed ISOC OUT transfer length is not DWORD
aligned, after closing descriptor HW leaves value of 4 - (ureq->length %
4) in the RX bytes. This is caused because DMA works using 4B chunks.
Example: if length = 9 and all 9 bytes were received from the bus, after
xfercomplete rx_bytes value is 3. Hence add this value to the amount of
transferred bytes.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Enable the BNA (Buffer Not Available) interrupt in descriptor DMA mode.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For DDMA mode in case of isochronous transfers completion performed
differently than other transfer types. This is because each usb request
was mapped to one descriptor in the chain and SW gets xfercomplete
interrupt on all descriptors. The endpoint remains enabled until HW
processes last descriptor with "L" bit set or BNA interrupt gets
asserted for IN and OUT endpoints correspondingly.
Add function dwc2_gadget_complete_isoc_request_ddma() - completes one
isochronous request taken from endpoint's queue.
Add function dwc2_gadget_start_next_isoc_ddma() - tries to restart
isochronous endpoint if requests are pending. Check for EPENA. If the
endpoint was disabled, try to restart it after programming descriptor
chain prepared by SW earlier, switch SW to fill the other half of chain.
Add function dwc2_gadget_fill_isoc_desc() - initializes DMA descriptor
for isochronous transfer based on the received request data and endpoint
characteristics.
Added function dwc2_gadget_start_isoc_ddma() - prepare DMA chain for
isochronous transfer in DDMA, programs corresponding DMA address to
DEPDMA, enables the endpoint. This function is called once SW decides to
start isochronous IN or OUT transfer depend on reception of NAK or
OUTTknEPdis interrupts indicating first isochronous token arrival from
host.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DDMA mode incompISOOUT should be masked, similar as Bulk Out -
XferCompl and BNA should be handled. incompISOIN is not valid in DDMA
and is not getting asserted.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Preparing for isochronous transfers support adding in DDMA mode. In DDMA
isochronous transfers are handled differently compared to Slave and BDMA
modes. This is caused by fact that isoc requests contain data for one
frame/microframe. HW descriptor should contain data of one
frame/microframe as well. Hence each DMA descriptor in the chain will
correspond to one usb request.
Decided to divide endpoints descriptor chain to two halves - while one
will be processed by HW, other one will be under SW control. First part
will be passed to HW once ISOC traffic needs to be started. In parallel
to HW's work SW will keep creating new entries in the other half of
chain if new requests arrive in ep_queue routine. This will allow
passing of already pre-prepared descriptors to HW immediately after
endpoint gets disabled. The endpoint should be disabled once HW closes
descriptor with "L" bit set. Afterwards SW will switch to use first part
of chain if more requests are arriving.
Add two members to the dwc2_hsotg_ep structure to be used in isochronous
transfers' handling in DDMA mode:
-isoc_chain_num - indicates which half of EP descriptor chain can be
used by SW to add new queued requests while HW is
processing other half.
-next_desc - index which points to next not yet programmed descriptor in
the half of descriptor chain which is under SW control.
Also add initialization of these fields in function
dwc2_hsotg_ep_enable().
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add DCFG register field macro for descriptor DMA mode and update core
initialization routine to set that bit accordingly.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DDMA mode of operation IN status phase of control write transfer
should start after getting StsPhseRcvd interrupt. This interrupt is
issued by HW once host starts to send IN tokens after data stage.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The StsPhseRcvd interrupt should not be enabled in slave mode.
Also move the StsPhsRcvd interrupt checking in the endpoint interrupt
handler to the correct order according to the databook. The interrupt
itself will be implemented in a later commit.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Update transfer starting dwc2_hsotg_start_req() routine with call of
function dwc2_gadget_config_nonisoc_xfer_ddma() to fill descriptor
chain.
Add call of dwc2_gadget_get_xfersize_ddma() in
dwc2_hsotg_handle_outdone() and dwc2_hsotg_complete_in() interrupt
handlers for DDMA mode to get information on transferred data from
descriptors instead of DXEPTSIZ.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add dwc2_gadget_set_ep0_desc_chain() function to switch between EP0 DDMA
chains depend on the stage of control transfer.
Include EP0 DDMA chain selection during ep_queue called from
dwc2_hsotg_enqueue_setup() for setup stage. Selecting and filling DDMA
chain for status phase as well - add calls of
dwc2_gadget_set_ep0_desc_chain() and
dwc2_gadget_config_nonisoc_xfer_ddma() functions.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add DMA descriptor members to the dwc2_hsotg_ep structure.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add dwc2_gadget_get_chain_limit() function and its call in transfer
start routine to correctly estimate one go on transfer size if
descriptor DMA mode is selected.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Update dwc2_hsotg structure to add descriptor chains for EP 0: two DMA
descriptors for Setup phase, per one for IN/OUT data and status phases.
Add their allocation function dwc2_gadget_alloc_ctrl_desc_chains() and
its call during gadget probe.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a parameter for descriptor DMA and set it based on hardware
capabilities. This won't actually be used by the gadget until later,
when the descriptor DMA code is in place.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Update the dwc2 driver for the new behavior of the usb_endpoint_maxp()
and also use the new usb_endpoint_maxp_mult() helper function.
This commit fixes failures in high-badwith ISOC transfer tests.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move the gadget devicetree settings into the core_params structure and
document them. Then set and check them in params.c, with the addition of
some helper functions, and remove the equivalent code in gadget.c.
Because these parameters came from the standalone s3c driver, they have
a fixed default value rather than an autodetected one. Preserve and
document this behavior to avoid any compatibility issues.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This makes it consistent with the hw_params struct and simplifies the
memory management for future refactoring. Fix up usage in all files.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The combo of list_empty() check and return list_first_entry()
can be replaced with list_first_entry_or_null().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit aa381a7259 ("usb: dwc2: gadget: fix TX FIFO size
and address initialization").
The original commit removed the FIFO size programming per endpoint. The
DPTXFSIZn register is also used for DIEPTXFn and the SIZE field is r/w
in dedicated fifo mode. So it isn't appropriate to simply remove this
initialization as it might break existing behavior.
Also, some cores might not have enough fifo space to handle the
programming method used in the reverted patch, resulting in fifo
initialization failure.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit ba48eab886 ("usb: dwc2: gadget: change variable
name to more meaningful").
This is needed to cleanly revert commit aa381a7259 ("usb: dwc2:
gadget: fix TX FIFO size and address initialization") which may cause
regressions on some platforms.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In dwc2_hsotg_udc_start(), don't initialize the controller for device
mode unless we are actually in device mode.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As kill_all_requests() potentially flushes TX FIFO, we should should
free FIFO after calling it. Otherwise FIFO could stay unflushed properly.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since FIFO is always freed in dwc2_hsotg_ep_disable(), ep->fifo_index
is always 0 in dwc2_hsotg_ep_enable(), hence code inside if() block is
never executed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since we handle FIFOs and endpoint separately, using variable named 'ep'
in context of FIFO is misleading, hence we rename it to 'fifo'.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to DWC2 documentation, DPTxFSize field of DPTXFSIZn register
is read only, which means that software cannot change FIFO size.
Register description says:
"The value of this register is the Largest Device Mode Periodic Tx Data
FIFO Depth (parameter OTG_TX_DPERIO_DFIFO_DEPTH_n), as specified during
coreConsultant configuration."
That means, that we have to setup only FIFO start addresses (DPTxFStAddr),
taking into account reset values of DPTxFSize.
Initialize FIFO start addresses properly and remove unneeded core related
to incorrect FIFO size initialization.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In context of FIFO registers we use ep->fifo_index instead of ep->index.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Done fixes and tested hsotg gadget's BDMA mode. Tested Control,
Bulk, Isoc, Inter transfers. Added code for isoc transfers,
removed unusable code, done minor fixes. Affected functions
and IRQ handlers:
- dwc2_hsotg_start_req(),
- dwc2_hsotg_ep_enable(),
- dwc2_hsotg_ep_queue(),
- dwc2_hsotg_handle_outdone(),
- GINTSTS_GOUTNAKEFF handler,
Removed 'has_correct_parity' flag from 'dwc2_hsotg_ep' struct.
Before this patch series, to set the data pid the DWC2 gadget
driver was toggling the even/odd until it match, then were
leaving it set. But now I have added mechanism to set pid and
excluded all code where this flag was set.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reimplemented EP disabled interrupt handler and moved to
corresponding function.
This interrupt indicates that the endpoint has been disabled per
the application's request.
For IN endpoints flushes txfifo, in case of BULK clears DCTL_CGNPINNAK,
in case of ISOC completes current request.
For ISOC-OUT endpoints completes expired requests. If there is
remaining request starts it. This is the part of ISOC-OUT transfer
drop flow. When ISOC-OUT transfer expired we must disable ep to drop
ongoing transfer.
Tested-by: John Keeping <john@metanate.com>
Reviewed-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Incomplete ISO IN interrupt indicates one of the following conditions
occurred while transmitting an ISOC transaction.
- Corrupted IN Token for ISOC EP.
- Packet not complete in FIFO.
Incomplete ISO OUT indicates that there is at least one isochronous OUT
endpoint on which the transfer is not completed in the current
microframe.
The following actions will be taken:
In case of EP-IN
- Determine the EP
- Disable EP directly from this handler; when "Endpoint Disabled"
interrupt is received flush FIFO
In case of EP-OUT
- Determine the EP
- If target frame elapsed set DCTL_SGOUTNAK, unmask GOUTNAKEFF and
proceed as described in section 7.5.1 of DWC-HSOTG Programming Guide
Also added dwc2_gadget_target_frame_elapsed() helper function which
will be used in Incomplete ISO IN/OUT Interrupt handlers.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
NAKINTRPT interrupt is starting point for isoc-in transfer,
synchronization done with first in token received from host,
core asserts this interrupt when responds with 0 length data
to in token, received from host.
The first IN token is asynchronous for device - device does not
know when first one token will arrive from host. On first token
arrival HW generates 2 interrupts: 'in token received while FIFO
empty' and 'NAK'. NAK interrupt for ISOC in means that token has
arrived and ZLP was sent in response to that as there was no data
in FIFO. SW is basing on this interrupt to obtain frame in which
token has come and then based on the interval calculates next
frame for transfer.
OUTTKNEPDIS interrupt is starting point for isoc-out transfer,
synchronization done with first out token received from host
while corresponding ep is disabled.
For OUTs the reason is same - device does not know initial frame
in which out token will come. For this HW generates OUTTKNEPDIS
- out token is received while EP is disabled. Upon getting this
interrupt SW starts calculation for next transfer frame.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Replaced repeating code with function call.
Starts next request from ep queue.
If queue is empty and ep is isoc
-In case of OUT-EP unmasks OUTTKNEPDIS.
OUTTKNEPDIS is masked in it's handler, so we need to unmask it here
to be able to do resynchronization.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reads and returns interrupts for given endpoint, by masking epint_reg
with corresponding mask.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Calculate the interval according to the USB 2.0 specification section
9.6.6.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Increases and checks targeted frame number of current ep
if overrun happened, sets flag and masks with DSTS_SOFFN_LIMIT
Added following fields to struct dwc2_hsotg_ep
-target_frame: Targeted frame num to setup next ISOC transfer
-frame_overrun: Indicates SOF number overrun in DSTS
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According DWC-OTG databook, "GOUTNakEff" is read only and can be
cleared only by "DCTL.CGOUTNak", but here we do not need to clear
it because DWC-OTG programming guide says that before disabling
any OUT endpoint, the application must enable Global OUT NAK mode,
so if this mode is enabled we can continue without this step.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No-op change. Changed field names to prevent misunderstanding.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This chunk is not needed here. There is no functionality
depend on this, so if no-op, I think we do not need to have
this interrupt unmasked.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Removed "ctrl |= DXEPCTL_USBACTEP" from
dwc2_hsotg_start_req() function because this
step is done in dwc2_hsotg_ep_enable().
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a check in dwc2_hsotg_ep_sethalt() so that it does not halt
isochronous endpoints.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The gadget API function usb_ep_set_halt() expects the gadget to return
-EAGAIN if the ep is active. Add support for this behavior.
Otherwise this may break mass storage protocol if a STALL is attempted
on the endpoint.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In host slave mode, the core asserts the rxready, txfifoempty interrupts
that get serviced in the gadget irq handler. Prevent servicing of these
when not in the gadget mode of operation.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Replaced the WARN_ON with a check and return of -EINVAL in the
dwc2_hsotg_ep_enable function if ep0 is passed in.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The host/device mode set with dr_mode should be kept all the time,
not being changed to OTG in gadget setup (by overriding CFGUSB_FORCEDEVMODE
and CFGUSB_FORCEHOSTMODE bits).
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Przemek Rudy <prudy1@o2.pl>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move the register save and restore functions into the host and gadget
specific files.
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The "enumspd" field is located in register DSTS[2:1], but the code
which checks the bitfield does not shift the value accordingly. This
in turn causes incorrect detection of gadget link partner speed in
dwc2_hsotg_irq_enumdone() .
Shift the value accordingly to fix the problem with speed detection.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove call to dwc2_hsotg_init() from dwc2_gadget_init(). The
gadget_init function should not access any device registers because the
mode isn't guaranteed here.
Also, this is already called elsewhere before anything starts on the
gadget so it is not necessary here.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dwc2_core_reset() function exists in the core so use that one
instead.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the previously cached hw params in the gadget. This saves a reset
and force mode in the gadget initialization during probe and makes
getting the hardware parameters consistent between gadget and host.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When receiving GINTSTS_GINNAKEFF or GINTSTS_GOUTNAKEFF interrupt,
DCTL will be overwritten with DCTL_CGOUTNAK or DCTL_CGNPINNAK values.
Instead of overwriting it, write only needed bits.
It could cause an issue if GINTSTS_GINNAKEFF or GINTSTS_GOUTNAKEFF
interrupt is received after dwc2 disabled pullup by writing
DCTL_SFTDISCON bit.
Pullup will then be re-enabled whereas it should not.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
