Commit c0a77ec74f 'bnx2x: Add missing braces in
bnx2x:bnx2x_link_initialize' identified indentation problem, but resolved it
by adding braces instead of fixing the indentation. The braces now prevents a
config_init call in some cases, though it should be called regardless of that
condition. This patch removes the braces and fix the confusing indentation
that caused this mess.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
CC: Dave Jones <davej@redhat.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 60cad4e67b
"bnx2x: VF RSS support - VF side" fails to compile w/o
CONFIG_BNX2X_SRIOV option.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
Merge commit 06c54055be did a bad conflict resolution accidentally
leaving out a closing brace. Add it back.
This breaks a handful of defconfigs on ARM, so it'd be good to see it
applied pretty quickly.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
Accept and handle 40G link events.
Accept ethtool link settings of speed == 40000 && duplex, and set the
appropriate MCDI PHY capability.
This does not include reporting of 40G media types, as those have not
yet been assigned numbers in the MCDI protocol.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Conflicts:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
net/bridge/br_multicast.c
net/ipv6/sit.c
The conflicts were minor:
1) sit.c changes overlap with change to ip_tunnel_xmit() signature.
2) br_multicast.c had an overlap between computing max_delay using
msecs_to_jiffies and turning MLDV2_MRC() into an inline function
with a name using lowercase instead of uppercase letters.
3) stmmac had two overlapping changes, one which conditionally allocated
and hooked up a dma_cfg based upon the presence of the pbl OF property,
and another one handling store-and-forward DMA made. The latter of
which should not go into the new of_find_property() basic block.
Signed-off-by: David S. Miller <davem@davemloft.net>
The indentation here implies that the intent was for this to be a multiline if.
Introduced a few years ago in commit ec146a6f01 ("bnx2x: Modify XGXS functions")
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit implements the ->ndo_do_ioctl() operation so that the
PHY-related ioctl() calls can work from userspace, which allows
applications like mii-tool or mii-diag to do their job.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes a long-standing bug that has been reported by many
users: on some Armada 370 platforms, only the network interface that
has been used in U-Boot to tftp the kernel works properly in
Linux. The other network interfaces can see a 'link up', but are
unable to transmit data. The reports were generally made on the Armada
370-based Mirabox, but have also been given on the Armada 370-RD
board.
The network MAC in the Armada 370/XP (supported by the mvneta driver
in Linux) has a functionality that allows it to continuously poll the
PHY and directly update the MAC configuration accordingly (speed,
duplex, etc.). The very first versions of the driver submitted for
review were using this hardware mechanism, but due to this, the driver
was not integrated with the kernel phylib. Following reviews, the
driver was changed to use the phylib, and therefore a software based
polling. In software based polling, Linux regularly talks to the PHY
over the MDIO bus, and sees if the link status has changed. If it's
the case then the adjust_link() callback of the driver is called to
update the MAC configuration accordingly.
However, it turns out that the adjust_link() callback was not
configuring the hardware in a completely correct way: while it was
setting the speed and duplex bits correctly, it wasn't telling the
hardware to actually take into account those bits rather than what the
hardware-based PHY polling mechanism has concluded. So, in fact the
adjust_link() callback was basically a no-op.
However, the network happened to be working because on the network
interfaces used by U-Boot for tftp on Armada 370 platforms because the
hardware PHY polling was enabled by the bootloader, and left enabled
by Linux. However, the second network interface not used for tftp (or
both network interfaces if the kernel is loaded from USB, NAND or SD
card) didn't had the hardware PHY polling enabled.
This patch fixes this situation by:
(1) Making sure that the hardware PHY polling is disabled by clearing
the MVNETA_PHY_POLLING_ENABLE bit in the MVNETA_UNIT_CONTROL
register in the driver ->probe() function.
(2) Making sure that the duplex and speed selections made by the
adjust_link() callback are taken into account by clearing the
MVNETA_GMAC_AN_SPEED_EN and MVNETA_GMAC_AN_DUPLEX_EN bits in the
MVNETA_GMAC_AUTONEG_CONFIG register.
This patch has been tested on Armada 370 Mirabox, and now both network
interfaces are usable after boot.
[ Problem introduced by commit c5aff18 ("net: mvneta: driver for
Marvell Armada 370/XP network unit") ]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Jochen De Smet <jochen.armkernel@leahnim.org>
Cc: Peter Sanford <psanford@nearbuy.io>
Cc: Ethan Tuttle <ethan@ethantuttle.com>
Cc: Chény Yves-Gael <yves@cheny.fr>
Cc: Ryan Press <ryan@presslab.us>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: vdonnefort@lacie.com
Cc: stable@vger.kernel.org
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Vincent Donnefort <vdonnefort@gmail.com>
Tested-by: Yves-Gael Cheny <yves@cheny.fr>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the __LINK_STATE_START check to verify the device is running, in
favor of netif_running(). netif_running() performs the same check of
__LINK_STATE_START, so the code should behave the same.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Sorbica Shieh <sorbica@icplus.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
copying large files to a NFS mounted host was taking absurdly large
time.
Turns out that TX BD reclaim had a sublte bug.
Loop starts off from @txbd_dirty cursor and stops when it hits a BD
still in use by controller. However when it stops it needs to keep the
cursor at that very BD to resume scanning in next iteration. However it
was erroneously incrementing the cursor, causing the next scan(s) to
fail too, unless the BD chain was completely drained out.
[ARCLinux]$ ls -l -sh /disk/log.txt
17976 -rw-r--r-- 1 root root 17.5M Sep /disk/log.txt
========== Before =====================
[ARCLinux]$ time cp /disk/log.txt /mnt/.
real 31m 7.95s
user 0m 0.00s
sys 0m 0.10s
========== After =====================
[ARCLinux]$ time cp /disk/log.txt /mnt/.
real 0m 24.33s
user 0m 0.00s
sys 0m 0.19s
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com> (commit_signer:3/4=75%)
Cc: "David S. Miller" <davem@davemloft.net> (commit_signer:3/4=75%)
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: arc-linux-dev@synopsys.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 82dc3c63 ("net: introduce NAPI_POLL_WEIGHT")
netif_napi_add() produces an error message if a NAPI poll weight
greater than 64 is requested.
qlcnic requests the weight as large as 256 for some of its rings, and
smaller values for other rings. For instance in qlcnic_82xx_napi_add()
I think the intention was to give the tx+rx ring a bigger weight than
to rx-only rings, but it's actually doing the opposite. So I'm assuming
the weights do not really matter much.
Just use the standard NAPI weights for all rings.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this patch capabilities are added to the Vf driver to request
multiple queues over the VF PF channel, and the logic for requesting
rss configuration for said queues.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilong Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Receive Side Scaling for queues of
Virtual Functions on the PF side. This includes support for the
requests for multiple queues from VF drivers, configuration of the
HW for multiple queues per VF, and support for rss configuration
of said queues.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exposes symbols for usnic low latency driver that can be used to
register and unregister vNics as well to traverse the resources on vNics.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In servers with more than 1.1 TB of RAM, the existing 40/32 bit DMA
could cause failure as the DMA-able address could go outside the range
addressable using 40/32 bits.
The following patch first tried 64 bit DMA if possible, failover to 32
bit.
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <govindarajulu90@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch sets the skb->rxhash and skb->q_number.
This is used by RPS and RFS. Kernel can make use of hw provided hash
instead of calculating the hash.
Signed-off-by: Govindarajulu Varadarajan <govindarajulu90@gmail.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch adds multi tx support for enic.
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <govindarajulu90@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Large ocrdma HW driver update: add "fast register" work requests,
fixes, cleanups
- Add receive flow steering support for raw QPs
- Fix IPoIB neighbour race that leads to crash
- iSER updates including support for using "fast register" memory
registration
- IPv6 support for iWARP
- XRC transport fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABCAAGBQJSJ2drAAoJEENa44ZhAt0hpaUQAJ6EdNFh2bon9c/uHz1lw58A
DIvVniUwWGCRgpbsv/IxZDBVX3G5IKSW6U0Y3/JxMXeIF/cGOUaJZgCeKPiYNoNA
yxiEGI0ffvpWGAJUHSE2ARJKvgdjrpqGo5UzsiinEhJx3uczeZBcooosQTWDXxya
/qSWH3rARkic9abuaizkuVzdWEjWLNjyh2bWnqJ4HNZplE8RfSK4bk8QtvEmpn9Z
dNBKFFujysfHHGflLuSkFAkP1NdqlZeQ4/2uzD23p3YofbJwrJoJNFxkCfx3UUml
fjPptlhU6kZMCwSXsD24tAV8Exr/CCgmxriFIN/Xqhu4gvBELScRPPqPqFquhtXI
pP5hbG9/9P5C8BLgABe6IAvlU1lUyraR67bA78nYeKm2JpATE6T23Nx7nUgMgzRS
Ee3ZvZGZvk8BZ7zyQh8D7Aig1XOtzqA9D5nLUyEJ2aRPSnXJxyi0S3Fbn0vmOMb7
8CF+99KECG8fb4sjNAjX5Zm48+7WJd+WCd3t89oUzCbJKKpa1Chctph8VH7dEfke
JkEjOJhuAGqau4bIMZ2nZkISoTfSD7vbjPAxMPASS7fOdR7fe6AqDn9/LMAhWjpw
4Fb25ZW7rYf9+6jqA4MgMRFCTkXhR25FsqUUL9h8NaWai4F1dfVoZHbRvGIZah5n
5HQupXGquwES4y6pvHjc
=rabl
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull main batch of InfiniBand/RDMA changes from Roland Dreier:
- Large ocrdma HW driver update: add "fast register" work requests,
fixes, cleanups
- Add receive flow steering support for raw QPs
- Fix IPoIB neighbour race that leads to crash
- iSER updates including support for using "fast register" memory
registration
- IPv6 support for iWARP
- XRC transport fixes
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (54 commits)
RDMA/ocrdma: Fix compiler warning about int/pointer size mismatch
IB/iser: Fix redundant pointer check in dealloc flow
IB/iser: Fix possible memory leak in iser_create_frwr_pool()
IB/qib: Move COUNTER_MASK definition within qib_mad.h header guards
RDMA/ocrdma: Fix passing wrong opcode to modify_srq
RDMA/ocrdma: Fill PVID in UMC case
RDMA/ocrdma: Add ABI versioning support
RDMA/ocrdma: Consider multiple SGES in case of DPP
RDMA/ocrdma: Fix for displaying proper link speed
RDMA/ocrdma: Increase STAG array size
RDMA/ocrdma: Dont use PD 0 for userpace CQ DB
RDMA/ocrdma: FRMA code cleanup
RDMA/ocrdma: For ERX2 irrespective of Qid, num_posted offset is 24
RDMA/ocrdma: Fix to work with even a single MSI-X vector
RDMA/ocrdma: Remove the MTU check based on Ethernet MTU
RDMA/ocrdma: Add support for fast register work requests (FRWR)
RDMA/ocrdma: Create IRD queue fix
IB/core: Better checking of userspace values for receive flow steering
IB/mlx4: Add receive flow steering support
IB/core: Export ib_create/destroy_flow through uverbs
...
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LeaW
-----END PGP SIGNATURE-----
Merge tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
While implementing NAPI for the driver, I overlooked the race conditions where
interrupt handler might have called napi_schedule_prep() before napi_enable()
was called or after napi_disable() was called. If RX interrupt happens, this
would cause the endless interrupts and messages like:
sh-eth eth0: ignoring interrupt, status 0x00040000, mask 0x01ff009f.
The interrupt wouldn't even be masked by the kernel eventually since the handler
would return IRQ_HANDLED all the time.
As a fix, move napi_enable() call before request_irq() call and napi_disable()
call after free_irq() call.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The synopsys spec says When TSCRLSSR is cleard, the rollover value of
sub-second register is 0x7FFFFFFF(0.465 ns per clock).
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug: error to get the previous BD entry. When the current BD
is the first BD, the previous BD entry must be the last BD,
not "bdp - 1" in current logic.
V4:
* Optimize fec_enet_get_nextdesc() for code clean.
Replace "ex_new_bd - ring_size" with "ex_base".
Replace "new_bd - ring_size" with "base".
V3:
* Restore the API name because David suggest to use fec_enet_
prefix for all function in fec driver.
So, change next_bd() -> fec_enet_get_nextdesc()
change pre_bd() -> fec_enet_get_prevdesc()
* Reduce the two APIs parameters for easy to call.
V2:
* Add tx_ring_size and rx_ring_size to struct fec_enet_private.
* Replace api fec_enet_get_nextdesc() with next_bd().
Replace api fec_enet_get_prevdesc() with pre_bd().
* Move all ring size check logic to next_bd() and pre_bd(), which
simplifies the code redundancy.
V1:
* Add BD ring size check to get the previous BD entry in correctly.
Reviewed-by: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Frank Li <frank.li@freescale.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver supporting NAPI should use NAPI-specific function for receiving packets,
so netif_rx() should be changed to netif_receive_skb().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free_irq is not needed if there has been no request_irq. Free_irq is
removed from both the probe and remove functions. The correct request_irq
and free_irq are found in the open and close functions.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
*e = platform_get_irq(...);
... when != request_irq(e,...)
*free_irq(e,...)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
It upsets static analyzers when we don't check for allocation failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates igb driver version to 5.0.5
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the way we report supported/advertised link for i354
devices, especially for 2.5 GB. Instead of reporting 2.5 GB for all i354
devices erroneously, check first, if it is 2.5 GB capable.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes how we get speed/duplex for non_copper devices; it
now uses pcs register to get current speed and duplex instead of using
generic status register that we use to detect speed/duplex for copper
devices.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since i354 2.5Gb devices are not Copper media type but SerDes, so this
patch changes the way we detect speed/duplex link info for this device.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
PHY Power Management does not exist for i354 device. So, there is no
need to read and write this register or clear go link Disconnect bit,
which could cause a lot of issues.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements downshift mechanism for M88E1543 PHY, so that
downshift is disabled first during link setup process, and later enabled
if we are master and downshift link is negotiated. Also cleaned up
return code implementation.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes PHY_ID for i354 device, now using M88E1543
instead of M88E1545.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds 1 sec delay mechanism to i210 device family, in order
to avoid erroneous link issue with the link partner.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a part is flashless, do not look for a PBA in the iNVM.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just remove a small semicolon.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes warning "warning: symbol 'qlcnic_set_dcb_ops' was
not declared. Should it be static?"
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hypervisor is big endian, so little endian kernel builds need
to byteswap.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casting from 'void *' is unnecessary, because casting from 'void *'
to any pointer type is automatic.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use bp->pfid from bnx2x instead to avoid duplication.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use BP_PORT and chip_port_mode directly from bnx2x.h to avoid duplication.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This eliminates duplication and ensures that all bnx2x chips will be
supported.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data
using pci_dev instead of using dev_{get,set}_drvdata() with
&pdev->dev, so we can directly pass a struct pci_dev. This is
a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data
using pci_dev instead of using dev_{get,set}_drvdata() with
&pdev->dev, so we can directly pass a struct pci_dev. This is
a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data
using platform_device instead of using dev_{get,set}_drvdata()
with &pdev->dev, so we can directly pass a struct platform_device.
This is a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data
using platform_device instead of using dev_{get,set}_drvdata()
with &pdev->dev, so we can directly pass a struct platform_device.
This is a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently only H8300H_AKI3068NET and H8300H_H8MAX define default
I/O base and IRQ values for the NE_H8300 driver. Hence builds
for other H8300H platforms will fail as per below. Since H8300H
does not support multi platform builds, we simply limit building
the driver to those two platforms specifically.
The release error:
drivers/net/ethernet/8390/ne-h8300.c: In function 'init_dev':
drivers/net/ethernet/8390/ne-h8300.c:117:23: error: 'h8300_ne_base' undeclared (first use in this function)
drivers/net/ethernet/8390/ne-h8300.c:117:23: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/ethernet/8390/ne-h8300.c:117:23: error: bit-field '<anonymous>' width not an integer constant
drivers/net/ethernet/8390/ne-h8300.c:119:20: error: 'h8300_ne_irq' undeclared (first use in this function)
drivers/net/ethernet/8390/ne-h8300.c: In function 'init_module':
drivers/net/ethernet/8390/ne-h8300.c:647:21: error: 'h8300_ne_base' undeclared (first use in this function)
drivers/net/ethernet/8390/ne-h8300.c:648:15: error: 'h8300_ne_irq' undeclared (first use in this function)
drivers/net/ethernet/8390/ne-h8300.c:661:4: warning: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'long unsigned int' [-Wformat]
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script: (and a little typing)
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turning off led on port 0 of the 5719 serdes causes all other ports to
lose power and stop functioning. Add tg3_phy_led_bug() function to check
for this condition. We use a switch() in tg3_phy_led_bug() for
consistency with the tg3_phy_power_bug() function.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a DMA mapping error in xgmac_xmit, we should simply free the skb and
return NETDEV_TX_OK rather than -EIO. In the case of errors in mapping
frags, we need to undo everything that has been setup.
Reported-by: Andreas Herrmann <andreas.herrmann@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the mismatch in the DMA mapping and unmapping sizes for receive. The
unmap size must be equal to the map size and should not be the actual
received frame length. The map size should also be adjusted by the
NET_IP_ALIGN size since the h/w buffer size (dma_buf_sz) includes this
offset.
Also, add a missing dma_mapping_error check in xgmac_rx_refill.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_sa_filter_fail and tx_undeflow events are unused and impossible
to occur based on how the h/w is used. We never filter on source MAC
address and TX store and forward mode prevents underflow events.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix xgmac_set_rx_mode to handle several conditions that were not handled
correctly as Lennert Buytenhek describes:
If we have, say, 100 unicast addresses, and 5 multicast addresses, the
unicast address count check will evaluate to true, and set use_hash to
true. The multicast address check will however evaluate to false, and
use_hash won't be set to true again, and XGMAC_FRAME_FILTER_HMC won't
be OR'd into XGMAC_FRAME_FILTER, but since use_hash was still true
from the unicast check, netdev_for_each_mc_addr() will program the
multicast addresses into the hash table instead of using the MAC
address registers, but since the HMC bit wasn't set, the hash table
won't be checked for multicast addresses on receive, and we'll stop
receiving multicast packets entirely.
Also, there is no code that zeroes out MAC address registers reg..31
at the end of this function, meaning that under the right conditions,
unicast/multicast addresses that were previously in the filter but
were then deleted won't be cleared out.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a race condition where the interrupt handler may have called
napi_schedule before napi_enable is called. This would disable interrupts
and never actually schedule napi to run.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the xgmac transmit start and completion work locklessly, it is
possible for xgmac_xmit to stop the tx queue after the xgmac_tx_complete
has run resulting in the tx queue never being woken up. Fix this by
ensuring that ring buffer index updates are visible and recheck the ring
space after stopping the queue. Also fix an off-by-one bug where we need
to stop the queue when the ring buffer space is equal to MAX_SKB_FRAGS.
The implementation used here was copied from
drivers/net/ethernet/broadcom/tg3.c.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that the descriptor writes are visible before the ring buffer head
is updated. Since writel is a barrier, we can simply update the head after
the writel.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX completion code may have freed an skb before the entire sg list
was transmitted. The DMA unmap calls for the fragments could also get
skipped. Now set the skb pointer on every entry in the ring, not just
the head of the sg list. We then use the FS (first segment) bit in the
descriptors to determine skb head vs. fragment.
This also fixes similar bug in xgmac_free_tx_skbufs where clean-up of
a sg list that wraps at the end of the ring buffer would not get
unmapped.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for the xgmac_tx_complete to run concurrently with
xgmac_tx_err since there are no locks. Fix this by moving the tx
error handling to a workqueue so we can disable napi while we reset
the transmitter.
Reported-by: Andreas Herrmann <andreas.herrmann@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xgmac_desc_get_buf_len appears to have a copy/paste error. flags is the
wrong field to read. We should be reading buf_size field. cpu_to_le32
should also be le32_to_cpu. This never really mattered as this function
is only used for DMA mapping calls which happen to be nops with coherent
DMA.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xgmac does not actually handle frag lists, so this option should not
be set. It does not appear to have had any impact though.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SkyHawk-R can support VEB or VEPA mode.
This patch will allow the user to set/query this switch setting.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the amount of sent bytes reported to BQL by reporting the
number of bytes on wire in the xmit routine, and recording that
value for each skb in order to be correctly confirmed on Tx
confirmation cleanup.
Reporting skb->len to BQL just before exiting xmit is not correct
due to possible insertions of TOE block and alignment bytes in the
skb->data, which are being stripped off by the controller before
transmission on wire. This led to mismatch of (incorrectly)
reported bytes to BQL b/w xmit and Tx confirmation, resulting in
Tx timeout firing, for the h/w tx timestamping acceleration case.
There's no easy way to obtain the number of bytes on wire in the Tx
confirmation routine, so skb->cb is used to convey that information
from xmit to Tx confirmation, for now (as proposed by Eric). Revived
the currently unused GFAR_CB() construct for that purpose.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This corrects an oversight when r8a7790 support was added to sh_eth.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlIPcACgkQMUfUDdst+ynUMwCaAnITsxyDXYQ4DqEsz8EcOtMk
718AoLrgnUZs3B+70AT34DVktg4HSThk
=USl9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
There is an embedded switch per physical port on the adapter.
Add support for enabling and disabling the embedded switch
on per port basis.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Removed unused and unnecessary members from qlc_83xx_fw_info
structure.
o Made fw_info member of qlcnic_hardware_context as a pointer to
qlc_83xx_fw_info structure.
o Added a member fw_file_name to qlc_83xx_fw_info structure which
will hold the name of firmware image file name.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Generic AER callback handlers will make use of qlcnic_hardware_ops structure
to call adapter specific handlers.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-Use CAMRAM register to store firmware dump state in adapter
instead of maintaining it in each function driver separately.
-Return appropriate error code on failure
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Remove inline keyword from function prototypes wherever it is not appropriate.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o PF driver should not indicate PVID configuration to VF driver.
As adapter supports VLAN stripping, VF driver should stay agnostic
to any PVID configuration.
o Return "QLC_NO_VLAN_MODE(= 0)" to VFD when PVID is configured.
VF driver should be in no VLAN configuration mode.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
1. A little more refactoring.
2. Remove the unnecessary use of atomic_t that you pointed out.
3. Add support for starting or queueing firmware requests from atomic
context.
4. Add hwmon support for additional sensors found on some new boards.
5. Add support for the EF10 controller architecture, the SFC9100 family
and specifically the SFC9120 controller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dc975382 "net: fec: add napi support to improve proformance"
converted the fec driver to the napi model. However, that commit
forgot to remove the call to skb_defer_rx_timestamp which is only
needed in non-napi drivers.
(The function napi_gro_receive eventually calls netif_receive_skb,
which in turn calls skb_defer_rx_timestamp.)
This patch should also be applied to the 3.9 and 3.10 kernels.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My static checker complains that on some arches unsigned longs can be 8
characters which is larger than the buffer is only 6 chars.
Additionally, Ben Hutchings points out that the buffer actually holds
big endian data and the buffer we are reading from is CPU endian.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some synopsys ip implementation doesn't support DMA store and forward mode,
such as BF60x. So, set force_thresh_dma_mode to use DMA thresholds only.
Update document and devicetree as well.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__GFP_ZERO is an uncommon flag and perhaps is better
not used. static inline dma_zalloc_coherent exists
so convert the uses of dma_alloc_coherent with __GFP_ZERO
to the more common kernel style with zalloc.
Remove memset from the static inline dma_zalloc_coherent
and add just one use of __GFP_ZERO instead.
Trivially reduces the size of the existing uses of
dma_zalloc_coherent.
Realign arguments as appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the dates for files that have been added to in 2012-2013.
Drop the 'Solarstorm' brand name that's still lingering here.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
There's no need to call ether_setup() in the driver since prior alloc_etherdev()
call already arranges for it.
Suggested-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to ixgbe.
Jacob provides a fix for 82599 devices where it can potentially keep link
lights up when the adapter has gone down.
Mark provides a fix to resolve the possible use of uninitialized memory
by checking the return value on EEPROM reads.
Don provides 2 patches, one to fix a issue where we were traversing the
Tx ring with the value of IXGBE_NUM_RX_QUEUES which currently happens
to have the correct value but this is misleading. A change later, could
easily make this no longer correct so when traversing the Tx ring, use
netdev->num_tx_queues. His second patch does some minor clean ups of log
messages.
Emil provides the remaining ixgbe patches. First he fixes the link test
where forcing the laser before the link check can lead to inconsistent
results because it does not guarantee that the link will be negotiated
correctly. Then he initializes the message buffer array to 0 in order
to avoid using random numbers from the memory as a MAC address for the
VF. Emil also fixes the read loop for the I2C data to account for the
offset for SFP+ modules. Lastly, Emil provides several patches to add
support for QSFP modules where 1Gbps support is added as well as support
for older QSFP active direct attach cables which pre-date SFF-8436 v3.6.
v2: Fixed patch 4 description and added blank line based on feedback from
Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a custom 'FEC_NAPI_WEIGHT', just use the generic
'NAPI_POLL_WEIGHT' definition instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace misleading -1 (-EPERM) by a more appropriate return code (-ENXIO)
in macb_mii_probe function.
Save macb_mii_probe return before branching to err_out_unregister to avoid
erronous 0 return.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the EF10 network controller architecture and the
SFC9100 family, starting with SFC9120 'Farmingdale', and bumps the
driver version to 4.0.
New features in the SFC9100 family include:
- Flexible allocation of internal resources to PCIe physical and virtual
functions under firmware control
- RX event merging to reduce DMA writes at high packet rates
- Integrated RX timestamping
- PIO buffers for lower TX latency
- Firmware-driven data path that supports additional offload features
and filter types
- Delivery of packets between functions and to multiple recipients,
allowing firmware to implement a vswitch
- Multiple RX flow hash (RSS) contexts with their own hash keys and
indirection tables
- 40G MAC (single port only)
...not all of which are enabled in this initial driver or the initial
firmware release.
Much of the new code is by Jon Cooper.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Also update comments and assertions in io.h:
- EF10 does not have a general BIU collector and does not have the
bug affecting TIMER_COMMAND_REG[0] on Falcon/Siena
- The WPTR field moved within RX_DESC_UPD_REG and TX_DESC_UPD_REG.
Adjust efx_writed_page() accordingly
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The TX path firmware for EF10 supports 'option descriptors' to control
offloads and various other features. Add a flag and field for these
in struct efx_tx_buffer, and don't treat them as DMA descriptors on
completion.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
On EF10, the firmware will initiate a queue flush in certain
error cases. We need to accept that flush events might appear
at any time after a queue has been initialised, not just when
we try to flush them.
We can handle Falcon-architecture in just the same way.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
RX DMA scatter is always enabled on EF10. Adjust the common RX
completion handling to allow for this.
RX completion events on EF10 include the length used from a single
descriptor, not the cumulative length used. Add a field to struct
efx_rx_queue to hold the cumulative length.
[bwh: Also fix a related comment]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add the efx_filter_is_mc_recip() function to decide whether a filter
is for a multicast recipient and can coexist with other filters with
the same match values. Update efx_filter_insert_filter() kernel-doc
to explain the conditions for this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We can set, get and compare-and-exchange without using atomic_t.
Change efx_mcdi_iface::state to the enum type we really wanted it to
be.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add support for power and current sensors, which need to be named
differently in sysfs. Power sensors also require values to be scaled
between MCDI and sysfs, and have no minimum value.
Add definitions of the power, current, fan, and additional temperature
and voltage sensors found on SFA6902F, SFN7022F and SFN7122F.
(Includes a bug fix from Andrew Jackson.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This patch adds support for QSFP active direct attach (DA) cables which
pre-date SFF-8436 v3.6.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure that QSFP+ modules use the SFP+ code path for
setting up link.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds GB speed support for QSFP+ modules.
Autonegotiation is not supported with QSFP+. The user will have to set
the desired speed on both link partners using ethtool advertise setting.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the read loop for the I2C data to account for the offset.
Also includes a whitespace cleanup and removes ret_val as it is not needed.
CC: Ben Hutchings <bhutchings@solarflare.com>
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some minor log messages cleanup, changing the level one message is logged,
adding a bit of detail to another and put all the text on one line.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch initializes the msgbuf array to 0 in order to avoid using random
numbers from the memory as MAC address for the VF.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a partial reverse of:
commit dfcc4615f0
Author: Jacob Keller <jacob.e.keller@intel.com>
Date: Thu Nov 8 07:07:08 2012 +0000
ixgbe: ethtool ixgbe_diag_test cleanup
Specifically forcing the laser before the link check can lead to
inconsistent results because it does not guarantee that the link will be
negotiated correctly. Such is the case when dual speed SFP+ module is
connected to a gigabit link partner.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were transversing the tx_ring with IXGBE_NUM_RX_QUEUES. Now this define
happens to have the correct value but this is misleading and a change later
could easily make this no longer true. I updated it to netdev->num_tx_queues
like we use in ixgbe_get_strings().
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the possible use of uninitialized memory by checking the
return value on eeprom reads. These issues were identified by static
analysis. In many cases error messages will be produced so that corrupted
eeprom issues will be more visible.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue with the 82599 adapter where it can potentially keep
link lights up when the adapter has gone down. The patch adds a function which
ensures link is disabled, and calls this function when the adapter transitions
to a down state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ben Hutchings says:
====================
1. Further cleanup and refactoring in preparation for EF10.
2. Remove ethtool stats that are always zero on Falcon boards.
3. Add an ethtool stat for merged TX completions.
4. Prepare to support merged RX completions.
5. Prepare to support more hwmon sensors.
6. Add support for new events that are generated by EF10 firmware.
7. Update MC reboot detection for EF10.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This function checks the upper bound but it doesn't check for negative
numbers:
if (txq > QLCNIC_MAX_TX_RINGS) {
I've solved this by making "txq" a u32 type. I chose that because
->tx_count in the ethtool_channels struct is a __u32.
This bug was added in aa4a1f7df7 ('qlcnic: Enable Tx queue changes using
ethtool for 82xx Series adapter.').
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed the pbl(programmable burst length) setting
using DT. Even though the default pbl is 8, If there is no
pbl property in device tree file, pbl is set 0 and it causes
bandwidth degradation.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the PF gathers statistics for the VF, when the VF is about to unload
we must synchronize the release of its statistics buffer with the PF, so that
no DMA operation will be made to that address after the buffer release.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to incorrect VF/PF conditions, when unloading a VF it will not release
part of the memory it has previously allocated.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
