DISPC pipeline DMAs preload some bytes of pixel data in the vertical blanking
region before the start of each frame. The preload ensures the pipeline doesn't
underflow when the active region of the display starts.
DISPC_GFX/VIDp_PRELOAD registers allow us to program how many bytes of data
should be preloaded for each pipeline. Calculating a precise preload value
would be a complex function of the pixel clock of the connected display, the
vertical blanking duration and the interconnect traffic at that instance. If
the register is left untouched, a default value is preloaded.
We observe underflows for OMAP4+ SoCs for certain bandwidth intensive use cases
with many other initiators active, and in situations where memory access isn't
very efficient(like accessing Tiler mapped buffers and EMIF configured in
non-interleaved more). The cause of the underflow is because the default preload
value isn't sufficient for the DMA to reach a steady state. We configure the
PRELOAD register such that the pipelines preload data up to the high threshold
of the FIFO.
Preloading lot of data for older SoCs can have a negative impact. Due to slower
interconnects, it's possible that the DISPC DMA cannot preload up to the high
threshold within the vertical blanking region of the panel. We leave the PRELOAD
registers to their reset values since we haven't faced underflows with these
SoCs because of low value of PRELOAD.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When omapfb module is removed, the driver will turn off all the displays
it manages. However, it leaves the overlays enabled. While the overlays
are obviously disabled as the displays are disabled, it causes issues
when the driver module is loaded again, as at that point the overlays
are still enabled on the hardware level. The result is that even if the
SW thinks overlays are disabled, they are actually enabled.
Fix this by making sure the overlays are disabled at module removal.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Nowadays it's normal to get -EPROBE_DEFER from, e.g., regulator_get. As
-EPROBE_DEFER is not really an error, and the driver will be probed fine
a bit later, printing an error message will just confuse the user.
This patch changes omapdss to print an error for regulator_gets only if
the error code is something else than -EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It is quite common to have omapfb probe deferred because of a missing
resource, and to get omapfb probed succesfully a bit later. This works
fine. However, omapfb does not give any print on a successful probe, so
if the omapfb is actually never probed again after deferral, this is not
shown in the log.
To help debugging, add a simple print from omapfb at the end of its
probe, saying which display it is using and in which resolution.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HDMI driver tries to get the needed memory resources by name and by
ID. Resources by name are not currently defined, and will be used with
DT boot.
The resource names used in the driver are not quite perfect, and as they
are not used yet, we can change them. This patch removes the unneeded
"hdmi_" prefix from the names, and simplifies the names (e.g. hdmi_txphy
-> phy).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSI contains three separate blocks: protocol engine, PHY and PLL. At the
moment, all these are memory mapped in one big chunk. We need to split
that memory map into smaller pieces so that we can add proper 'reg'
properties into the DT data for each block.
This patch changes the driver to map the blocks separately. It first
tries to get the memory resource using name, used when booting with DT,
and if that fails, it gets the memory resource by ID, in which case the
driver gets the big chunk from platform data. That big chunk is then
split into the smaller blocks manually.
After DSS DT code has been merged and the old platform code removed, we
can clean up the memory resource management.
Instead of changing the driver in all the places where a register is
read or written, this patch takes a shortcut: it adds an additional
number to the struct which represents the register index. This number is
used to decide which base address to use. In the future we should
consider other approaches.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
hdmi_wait_for_bit_change() has two issues:
The register index was passed as u16, even if the register index may be
u32. Fix the index to u32.
The function was copied from wait_for_bit_change() which waits for a
single bit to change, but the hdmi version was changed to wait for a bit
field. This change was not done correctly.
The function is supposed to return the (last) value of the bit field,
but it returned !val in case of timeout. This was correct for the single
bit version, but not for the hdmi version. Fix the function to return
the actual value in the register.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DISPC_MSTANDBY_CTRL register is used in the driver, but it's not
restored in dispc_restore_context(), causing problems after resume.
Instead of adding DISPC_MSTANDBY_CTRL to dispc_restore_context(), let's
call _omap_dispc_initial_config() as the first thing in
dispc_runtime_resume(). This will initialize the DISPC core registers
properly, and will avoid similar issues in the future.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For some reason the hdmi driver first turns off the video output when
it's about to enable the video output. This serves no purpose, and can
be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The hdmi4 driver currently rejects any timing which is not from the CEA or VESA
standards. This leads hdmi rejecting any non-standard mode. A non standard
timing may not have a valid code corresponding to it. In such cases, the HDMI
spec suggests to set the code to 0.
Modify the driver to check if the timings fall within the range of the DISPC
TV overlay manager, and remove the check for an invalid code. Add a debug print
specifying the mode and code in hdmi_display_set_timing.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSI has separate TX and RX fifos. However, the current code only has one
field where the fifo size is stored, and the code for both TX and RX
config write to the same field. This has not caused issues, as we've
been using the same fifo sizes.
Fix this bug by creating separate fields for TX and RX fifo sizes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss in compat mode creates some sysfs files into the device's sysfs
directory, including a 'name' file. This works fine for
platform_devices, but breaks with i2c or spi devices, as those already
have a 'name' file.
Fix this by renaming the omapdss's 'name' file to 'display_name'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP5 has MFLAG feature in DISPC. Add the register definition and dump
it. The register is not used yet, though.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When omapfb does ovl->get_overlay_info, ovl->set_overlay_info, the set
function may fail even if the info has not been changed. This is because
omapdss doesn't initialize the info, but expect the caller to set valid
values.
Normally that is the case, but there is at least one corner case: if
omapfb has not allocated memory for the overlay yet, and the user uses
ioctl to disable the overlay to make sure it's disabled. In this case
get_overlay_info returns invalid data, but the user is only interested
in setting the overlay to disabled, not configuring it, and
set_overlay_info fails.
The issue is made possible by the omapfb's setup_plane ioctl, which
groups overlay configuration and overlay enable/disable bit into the
same struct. Thus, when you are disabling an overlay, you are also
configuring it.
This is a bit counter intuitive, so I think it's better to initialize
the info to some valid values.
The fields requiring initialization are color_mode and rotation_type,
and also we need to remove the check for (paddr == 0), as paddr is 0 for
unallocated overlay (but it's still fine to disable the overlay).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix debug prints all over omapdss:
* add missing linefeeds
* change pr_err/pr_debug to DSSERR/DSSDBG
* add missing DSS_SUBSYS_NAMEs
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Functions dispc_ovl_set_fifo_threshold and
dispc_ovl_compute_fifo_thresholds need to be exported. Add the
EXPORT_SYMBOLs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Another smallish batch of fixes, it's been quiet due to the holidays. Nothing
controversial here, a handful of things across the board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSwENxAAoJEIwa5zzehBx366gP/0qFx9RVr+PaRSR3faIWZ0+l
qOCoOJ4604aE7H9blhUOz7VoWMUfqy7vRnr5Brms73lNZGztBzIiS1bte7qRiHtQ
QZr7rV9hZpy4G7aiGWHT2wkqDSYlJb0mmb5Kxn72KznWmuod3alOVfeqtgGRDJD4
YnUAlI10KpGcYYQ2d6jwCvb/KBQrlufrxxRirgzm13JmiU2CzGpPWDpSx6E1/bQ6
4I8rzHehg2n0FQHIhNDsmSTbsRSPsVjRZ5iMZ4kh7PBSrHuwaLLSyKKf3P8cjGRe
dhdN06XLZCAk5JUIt6oQWN3XGq217cIDZyQKz4wapPIc2Do/MAWKhmad6JbJTJxO
nk/j/VJamAGKjh6OG5+BVVV1KAqwkY4zKKN4lSbV17NLxu6TlA3Jq0vTpCNCMDiQ
xuLgBifPyhJIlJKUAnc1Ev+DrNVOrRsq6keosayKHyeH3nW6mPTzTppHjLPNSI//
WYjbqqs7Pu1MzQgp11C4fIj5xeSpqvdUpQIYolJq51MyL5QGub7H28/jR0rU9sN1
1R9quyB53Z2RLSWV84o4j8qmlQwwu9v94KPkJ6Rkr1IU8a4WqRkAGTjbXAhEBAnb
FQ8uLBzaJbifWXmsnmcI4M5gm4HF4iJv+5J/l3hj7W/4l3B2XfKbyzBnEfJT1PFC
mSjTK4WRhemgztif285m
=FX+j
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another smallish batch of fixes, it's been quiet due to the holidays.
Nothing controversial here, a handful of things across the board"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: pxa: fix USB gadget driver compilation regression
ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
ARM: shmobile: r8a7790: fix shdi resource sizes
ARM: shmobile: bockw: fixup DMA mask
ARM: shmobile: armadillo: Add PWM backlight power supply
Pull x86 fixes from Peter Anvin:
"There is a small EFI fix and a big power regression fix in this batch.
My queue also had a fix for downing a CPU when there are insufficient
number of IRQ vectors available, but I'm holding that one for now due
to recent bug reports"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Don't select EFI from certain special ACPI drivers
x86 idle: Repair large-server 50-watt idle-power regression
- Fix for a cpufreq regression causing stale sysfs files to be left
behind during system resume if cpufreq_add_dev() fails for one or
more CPUs from Viresh Kumar.
- Fix for a bug in cpufreq causing CONFIG_CPU_FREQ_DEFAULT_* to be
ignored when the intel_pstate driver is used from Jason Baron.
- System suspend fix for a memory leak in pm_vt_switch_unregister()
that forgot to release objects after removing them from
pm_vt_switch_list. From Masami Ichikawa.
- Intel Valley View device ID and energy unit encoding update for the
(recently added) Intel RAPL (Running Average Power Limit) driver
from Jacob Pan.
- Intel Bay Trail SoC GPIO and ACPI device IDs for the Low Power
Subsystem (LPSS) ACPI driver from Paul Drews.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=vQDX
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes and new device IDs from Rafael Wysocki:
- Fix for a cpufreq regression causing stale sysfs files to be left
behind during system resume if cpufreq_add_dev() fails for one or
more CPUs from Viresh Kumar.
- Fix for a bug in cpufreq causing CONFIG_CPU_FREQ_DEFAULT_* to be
ignored when the intel_pstate driver is used from Jason Baron.
- System suspend fix for a memory leak in pm_vt_switch_unregister()
that forgot to release objects after removing them from
pm_vt_switch_list. From Masami Ichikawa.
- Intel Valley View device ID and energy unit encoding update for the
(recently added) Intel RAPL (Running Average Power Limit) driver from
Jacob Pan.
- Intel Bay Trail SoC GPIO and ACPI device IDs for the Low Power
Subsystem (LPSS) ACPI driver from Paul Drews.
* tag 'pm+acpi-3.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap / RAPL: add support for ValleyView Soc
PM / sleep: Fix memory leak in pm_vt_switch_unregister().
cpufreq: Use CONFIG_CPU_FREQ_DEFAULT_* to set initial policy for setpolicy drivers
cpufreq: remove sysfs files for CPUs which failed to come back after resume
ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs
the sparse IRQ conversion, fix DRA7 console output for earlyprintk,
and fix the LDP LCD backlight when DSS is built into the kernel and
not as a loadable module.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=3A1e
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/intc-ldp-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Fix a regression for wrong interrupt numbers for some devices after
the sparse IRQ conversion, fix DRA7 console output for earlyprintk,
and fix the LDP LCD backlight when DSS is built into the kernel and
not as a loadable module.
* tag 'omap-for-v3.13/intc-ldp-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
+ v3.13-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
* r8a7790 (R-Car H2) based Lager board
- Correct SHDI resource sizes
This bug has been present since sdhi resources were added to the r8a7790 by
8c9b1aa418 ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
templates") in v3.11-rc2.
* r8a7778 (R-Car M1) based Bock-W board
- Correct DMA mask
This resolves a regression introduced by 4dcfa60071
("ARM: DMA-API: better handing of DMA masks for coherent allocations")
in v3.12-rc1.
* r8a7740 (R-Mobile A1) based Armadillo board
- Add PWM backlight power supply
This resolves a regression introduced by 22ceeee16e
("pwm-backlight: Add power supply support") in v3.12.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6ai1
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Second Round of Renesas ARM based SoC Fixes for v3.13
* r8a7790 (R-Car H2) based Lager board
- Correct SHDI resource sizes
This bug has been present since sdhi resources were added to the r8a7790 by
8c9b1aa418 ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
templates") in v3.11-rc2.
* r8a7778 (R-Car M1) based Bock-W board
- Correct DMA mask
This resolves a regression introduced by 4dcfa60071
("ARM: DMA-API: better handing of DMA masks for coherent allocations")
in v3.12-rc1.
* r8a7740 (R-Mobile A1) based Armadillo board
- Add PWM backlight power supply
This resolves a regression introduced by 22ceeee16e
("pwm-backlight: Add power supply support") in v3.12.
* tag 'renesas-fixes2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: fix shdi resource sizes
ARM: shmobile: bockw: fixup DMA mask
ARM: shmobile: armadillo: Add PWM backlight power supply
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
After commit 88f718e3fa
"ARM: pxa: delete the custom GPIO header" a compilation
error was introduced in the PXA25x gadget driver.
An attempt to fix the problem was made in
commit b144e4ab1e
"usb: gadget: fix pxa25x compilation problems"
by explictly stating the driver needs the <mach/hardware.h>
header, which solved the compilation for a few boards,
such as the pxa255-idp and its defconfig.
However the Lubbock board has this special clause in
drivers/usb/gadget/pxa25x_udc.c:
This include file has an implicit dependency on
<mach/irqs.h> having been included before <mach/lubbock.h>
was included.
Before commit 88f718e3fa
"ARM: pxa: delete the custom GPIO header" this implicit
dependency for the pxa25x_udc compile on the Lubbock was
satisfied by <linux/gpio.h> implicitly including
<mach/gpio.h> which was in turn including <mach/irqs.h>,
apart from the earlier added <mach/hardware.h>.
Fix this by having the PXA25x <mach/lubbock.h> explicitly
include <mach/irqs.h>.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Greg Kroah-Hartmann <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
problems with GPMC, RNG, and ISP/IVA MMUs on OMAP2/3. The other fixes
some problems with DEBUG_LL on DRA7xx.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod_fixes_b_v3.13-rc/20131226021920/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=kOrX
-----END PGP SIGNATURE-----
Merge tag 'for-v3.13-rc/hwmod-fixes-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into debug-ll-and-ldp-backlight-fix
A few OMAP hwmod fixes for v3.13-rc. One patch fixes some IRQ
problems with GPMC, RNG, and ISP/IVA MMUs on OMAP2/3. The other fixes
some problems with DEBUG_LL on DRA7xx.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod_fixes_b_v3.13-rc/20131226021920/
Looks like the LCD panel on LDP has been broken quite a while, and
recently got fixed by commit 0b2aa8bed3 (gpio: twl4030: Fix regression
for twl gpio output). However, there's still an issue left where the panel
backlight does not come on if the LCD drivers are built into the
kernel.
Fix the issue by registering the DPI LCD panel only after the twl4030
GPIO has probed.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[tony@atomide.com: updated per Tomi's comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* pm-cpufreq:
cpufreq: Use CONFIG_CPU_FREQ_DEFAULT_* to set initial policy for setpolicy drivers
cpufreq: remove sysfs files for CPUs which failed to come back after resume
* pm-sleep:
PM / sleep: Fix memory leak in pm_vt_switch_unregister().
and a patch so that instead of BUG'ing we use the ext4_error()
framework to mark the file system is corrupted.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABCAAGBQJSuSZnAAoJENNvdpvBGATwp/8P/R/VjV1O4IhDmRxbc7mNAkoB
Mfh2Utnk9daGdMpSMhzWW6m3oyohA0ICledBusQ3ax6Ymg8jIcmGwm3rJ8gAXvR1
4g0rQ1nw3JEGROId58FnKB3fsEmOPlt4T/LKL4boY6BfER4yu1htH0zSKBuKqykt
feH9dMiaR1KMQ613eWY6GEonYaP8+nI1GxEfvrymInxznDPVuaLgR4oBMAmR8R76
9vfJfFHYjbk1wQ5UEv94tic8Hi055PGCRfsLc79QwxMr5KyKz+NydDUIjgKjP9pu
9sz8iuV79M5/hUguZY7HH9Xd0byZ+jPuNrpkrDqSNZYuArfIcsXKZM/dm7HOgFGQ
dQzf9S/kBzJvcSHuUchhS2cm6kxCsHaqo16Fxs5kP3TmB3TrVr7EV6uBS4cm53PJ
x6IdAORhbURfuJCRQOi/TDNUrb+ZHvIx7Gc1ujizczC3An7QurfYo7XY/rWfdj41
eIVy0+1gqvWJsbXGInni1hKbXMU3yTJ0MqQm05A7MW/G2G6eIgEVpz8MElm33jEE
VvC6KyZxpviRYPUmxxTbSa1vl0UG1rZdZXslgmlSyY1yItVmyTCIAG217JOTyhTX
Ae1aZEgzLYh6dQAwweme79WF4WsBPP28TOmW2xoOH7t04gMG0t+9b/RbUDtTPItc
HXNmIlFP9CULIQ1c2Cvh
=KPNa
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"A collection of bug fixes destined for stable and some printk cleanups
and a patch so that instead of BUG'ing we use the ext4_error()
framework to mark the file system is corrupted"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: add explicit casts when masking cluster sizes
ext4: fix deadlock when writing in ENOSPC conditions
jbd2: rename obsoleted msg JBD->JBD2
jbd2: revise KERN_EMERG error messages
jbd2: don't BUG but return ENOSPC if a handle runs out of space
ext4: Do not reserve clusters when fs doesn't support extents
ext4: fix del_timer() misuse for ->s_err_report
ext4: check for overlapping extents in ext4_valid_extent_entries()
ext4: fix use-after-free in ext4_mb_new_blocks
ext4: call ext4_error_inode() if jbd2_journal_dirty_metadata() fails
Commit 7d7e1eb (ARM: OMAP2+: Prepare for irqs.h removal) and commit
ec2c082 (ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ)
updated the way interrupts for OMAP2/3 devices are defined in the
HWMOD data structures to being an index plus a fixed offset (defined
by OMAP_INTC_START).
Couple of irqs in the OMAP2/3 hwmod data were misconfigured completely
as they were missing this OMAP_INTC_START relative offset. Add this
offset back to fix the incorrect irq data for the following modules:
OMAP2 - GPMC, RNG
OMAP3 - GPMC, ISP MMU & IVA MMU
Signed-off-by: Suman Anna <s-anna@ti.com>
Fixes: 7d7e1eba7e ("ARM: OMAP2+: Prepare for irqs.h removal")
Fixes: ec2c0825ca ("ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ")
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
With commit '7dedd34: ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with
DEBUG_LL' we moved from parsing cmdline to identify uart used for earlycon
to using the requsite hwmod CONFIG_DEBUG_OMAPxUARTy FLAGS.
On DRA7 though, we seem to be missing this flag, and atleast on the DRA7 EVM
where we use uart1 for console, boot fails with DEBUG_LL enabled.
Reported-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com> # on a different base
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Fixes: 7dedd34694 ("ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL")
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Pull block fixes from Jens Axboe:
- fix for a memory leak on certain unplug events
- a collection of bcache fixes from Kent and Nicolas
- a few null_blk fixes and updates form Matias
- a marking of static of functions in the stec pci-e driver
* 'for-linus' of git://git.kernel.dk/linux-block:
null_blk: support submit_queues on use_per_node_hctx
null_blk: set use_per_node_hctx param to false
null_blk: corrections to documentation
null_blk: warning on ignored submit_queues param
null_blk: refactor init and init errors code paths
null_blk: documentation
null_blk: mem garbage on NUMA systems during init
drivers: block: Mark the functions as static in skd_main.c
bcache: New writeback PD controller
bcache: bugfix for race between moving_gc and bucket_invalidate
bcache: fix for gc and writeback race
bcache: bugfix - moving_gc now moves only correct buckets
bcache: fix for gc crashing when no sectors are used
bcache: Fix heap_peek() macro
bcache: Fix for can_attach_cache()
bcache: Fix dirty_data accounting
bcache: Use uninterruptible sleep in writeback
bcache: kthread don't set writeback task to INTERUPTIBLE
block: fix memory leaks on unplugging block device
bcache: fix sparse non static symbol warning
Pull cgroup fixes from Tejun Heo:
"Two fixes. One fixes a bug in the error path of cgroup_create(). The
other changes cgrp->id lifetime rule so that the id doesn't get
recycled before all controller states are destroyed. This premature
id recycling made memcg malfunction"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: don't recycle cgroup id until all csses' have been destroyed
cgroup: fix cgroup_create() error handling path
Pull percpu fix from Tejun Heo:
"A single commit to fix a spurious sparse warning coming from
DEFINE_PER_CPU()'s hack to support the use of weak symbols. Shouldn't
cause observable behavior change"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: fix spurious sparse warnings from DEFINE_PER_CPU()
Pull libata fixes from Tejun Heo:
"There's one interseting commit - "libata, freezer: avoid block device
removal while system is frozen". It's an ugly hack working around a
deadlock condition between driver core resume and block layer device
removal paths through freezer which was made more reproducible by
writeback being converted to workqueue some releases ago. The bug has
nothing to do with libata but it's just an workaround which is easy to
backport. After discussion, Rafael and I seem to agree that we don't
really need kernel freezables - both kthread and workqueue. There are
few specific workqueues which constitute PM operations and require
freezing, which will be converted to use workqueue_set_max_active()
instead. All other kernel freezer uses are planned to be removed,
followed by the removal of kthread and workqueue freezer support,
hopefully.
Others are device-specific fixes. The most notable is the addition of
NO_NCQ_TRIM which is used to disable queued TRIM commands to Micro
M500 SSDs which otherwise suffers data corruption"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata, freezer: avoid block device removal while system is frozen
libata: implement ATA_HORKAGE_NO_NCQ_TRIM and apply it to Micro M500 SSDs
libata: disable a disk via libata.force params
ahci: bail out on ICH6 before using AHCI BAR
ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8
Pull ext2 fix from Jan Kara:
"One simple fix of oops in ext2 which was recently hit by Christoph"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext2: Fix oops in ext2_get_block() called from ext2_quota_write()
- Additional checks for uverbs to ensure forward compatibility, handle
malformed input better.
- Fix potential use-after-free in iWARP connection manager.
- Make a function static.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=bol6
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fixes from Roland Dreier:
"Last batch of InfiniBand/RDMA changes for 3.13 / 2014:
- Additional checks for uverbs to ensure forward compatibility,
handle malformed input better.
- Fix potential use-after-free in iWARP connection manager.
- Make a function static"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/uverbs: Check access to userspace response buffer in extended command
IB/uverbs: Check input length in flow steering uverbs
IB/uverbs: Set error code when fail to consume all flow_spec items
IB/uverbs: Check reserved fields in create_flow
IB/uverbs: Check comp_mask in destroy_flow
IB/uverbs: Check reserved field in extended command header
IB/uverbs: New macro to set pointers to NULL if length is 0 in INIT_UDATA()
IB/core: const'ify inbuf in struct ib_udata
RDMA/iwcm: Don't touch cm_id after deref in rem_ref
RDMA/cxgb4: Make _c4iw_write_mem_dma() static
selinux_setprocattr() does ptrace_parent(p) under task_lock(p),
but task_struct->alloc_lock doesn't pin ->parent or ->ptrace,
this looks confusing and triggers the "suspicious RCU usage"
warning because ptrace_parent() does rcu_dereference_check().
And in theory this is wrong, spin_lock()->preempt_disable()
doesn't necessarily imply rcu_read_lock() we need to access
the ->parent.
Reported-by: Evan McNabb <emcnabb@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Moore <pmoore@redhat.com>
Fix a broken networking check. Return an error if peer recv fails. If
secmark is active and the packet recv succeeds the peer recv error is
ignored.
Signed-off-by: Chad Hanson <chanson@trustedcs.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Moore <pmoore@redhat.com>
Pull drm fixes from Dave Airlie:
"Xmas fixes pull, all small nothing major, intel, radeon, one ttm
regression, and one build fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/ttm: Fix swapin regression
gpu: fix qxl missing crc32_le
drm/radeon: fix asic gfx values for scrapper asics
drm/i915: Use the correct GMCH_CTRL register for Sandybridge+
drm/radeon: check for 0 count in speaker allocation and SAD code
drm/radeon/dpm: disable ss on Cayman
drm/radeon/dce6: set correct number of audio pins
drm/i915: get a PC8 reference when enabling the power well
drm/i915: change CRTC assertion on LCPLL disable
drm/i915: Fix erroneous dereference of batch_obj inside reset_status
drm/i915: Prevent double unref following alloc failure during execbuffer
some (non-ARM) MMUless setups, so we're making that fix ARM-only for now.
Unfortunately, the ARM refactoring which broke kallsyms/perf was CC:stable,
so the fix (which broken non-ARM) was also CC:stable, so now the partial
reversion is also CC:stable...
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=g8Et
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio balloon driver fixes from Rusty Russell:
"Refactoring broke the balloon driver, and fixing kallsyms on ARM broke
some (non-ARM) MMUless setups, so we're making that fix ARM-only for
now.
Unfortunately, the ARM refactoring which broke kallsyms/perf was
CC:stable, so the fix (which broken non-ARM) was also CC:stable, so
now the partial reversion is also CC:stable..."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
scripts/link-vmlinux.sh: only filter kernel symbols for arm
virtio_balloon: update_balloon_size(): update correct field
Besides the 2 fixes for tricky corner cases in gem from Chris I've
promised already two patche from Paulo to fix pc8 warnings (both ported
from -next, bug report from Dave Jones) and one patch from to fix vga
enable/disable on snb+. That one is a really old bug, but apparently it
can cause machine hangs if you try hard enough with vgacon/efifb handover.
* tag 'drm-intel-fixes-2013-12-18' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Use the correct GMCH_CTRL register for Sandybridge+
drm/i915: get a PC8 reference when enabling the power well
drm/i915: change CRTC assertion on LCPLL disable
drm/i915: Fix erroneous dereference of batch_obj inside reset_status
drm/i915: Prevent double unref following alloc failure during execbuffer
- fix for a long standing corruption bug on some Trinity/Richland parts.
- Stability fix for cayman dpm
- audio fixes for dce6+
* 'drm-fixes-3.13' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix asic gfx values for scrapper asics
drm/radeon: check for 0 count in speaker allocation and SAD code
drm/radeon/dpm: disable ss on Cayman
drm/radeon/dce6: set correct number of audio pins
Commit "drm/ttm: Don't move non-existing data" didn't take the
swapped-out corner case into account. This patch corrects that.
Fixes blank screen after attempted suspend / hibernate on vmwgfx.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix build error: qxl uses crc32 functions so it needs to select
CRC32.
Also use angle quotes around a kernel header file name.
drivers/built-in.o: In function `qxl_display_read_client_monitors_config':
(.text+0x19d754): undefined reference to `crc32_le'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
