The video_unregister_device() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vfree() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
FM (frequency modulated) signal for SDR is generated by varying the
phase, where phase variation is proportional to input signal. It is
seen that, the larger phase increments leads to discontinuities in
the signal recovered after demodulation. Reducing the extent of phase
variation with respect to input signal, equivalent to reducing the
modulation index.
Tested using FM receiver flow graph in gnuradio-companion.
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The common implementation for sin/cos in include/linux/fixp-arith.h
has been improved recently to provide higher precision.
Replacing native implementation of sin/cos in vivid sdr with common
implementation. This serves two purposes:
1. Improved accuracy: the native implementation based on the Taylor
series is more prone to rounding errors.
2. Reuse of common function: this is better compared to maintaining
native versions for each driver.
Suggested by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cos table used at fixp-arith.h has only 8 bits of precision.
That causes problems if it is reused on other drivers.
As some media drivers require a higher precision sin/cos
implementation, replace the current implementation by one that
will provide 32 bits precision.
The values generated by the new implementation matches the
32 bit precision of glibc's sin for an angle measured in
integer degrees.
It also provides support for fractional angles via linear
interpolation. On experimental calculus, when used a table
with a 0.001 degree angle, the maximum error for sin is
0.000038, which is likely good enough for practical purposes.
There are some logic there that seems to be specific to the
usage inside ff-memless.c. Move those logic to there, as they're
not needed elsewhere.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In case allocation vb2_dma_sg_init_ctx() fails during cx8802_probe(), the
already allocated cx8802 device structure memory is not freed in the used
exit path. Thus adapt the cleanup handling accordingly. Detected by Coverity
CID 1260065.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Memory allocated for sh_vou_file is not deallocated
on error paths in sh_vou_open().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If NO_DMA=y:
warning: (VIDEO_OMAP2_VOUT && VIDEO_VIU && VIDEO_TIMBERDALE) selects VIDEOBUF_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)
drivers/built-in.o: In function `__videobuf_dc_free':
videobuf-dma-contig.c:(.text+0x6f4d32): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `__videobuf_dc_alloc':
videobuf-dma-contig.c:(.text+0x6f4fe6): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `__videobuf_mmap_mapper':
videobuf-dma-contig.c:(.text+0x6f518e): undefined reference to `dma_free_coherent'
Commit 244829226f ("[media] timberdale: do not select TIMB_DMA")
dropped the dependency of VIDEO_TIMBERDALE on DMADEVICES, and thus the
implicit dependency on HAS_DMA. VIDEO_TIMBERDALE selects
VIDEOBUF_DMA_CONTIG, which bypasses its dependency on HAS_DMA. Make
VIDEO_TIMBERDALE depend on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If NO_DMA=y:
warning: (VIDEO_AM437X_VPFE && VIDEO_DM365_VPFE && VIDEO_DT3155 && VIDEO_OMAP4) selects VIDEOBUF2_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:207: error: implicit declaration of function ‘dma_mmap_coherent’
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:390: error: implicit declaration of function ‘dma_get_sgtable’
VIDEO_AM437X_VPFE selects VIDEOBUF2_DMA_CONTIG, which bypasses its
dependency on HAS_DMA. Make VIDEO_AM437X_VPFE depend on HAS_DMA to fix
this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The if and the else code are identical - so the condition has no effect
on the effective code.
This patch removes the condition and the duplicated code.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the media controller (MC) is not enabled, it will compile
fine, but will fail at the linkedition:
ERROR: "media_device_unregister" [drivers/media/usb/siano/smsusb.ko] undefined!
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is really a simple function, but using it avoids to have
if's inside the drivers.
Also, the kABI becomes a little more clearer.
This shouldn't generate any overhead, and the type check
will happen when compiling with MC DVB enabled.
So, let's do it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c: In function ‘dvb_usbv2_adapter_dvb_exit’:
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:531:25: warning: unused variable ‘d’ [-Wunused-variable]
struct dvb_usb_device *d = adap_to_d(adap);
^
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:403:13: warning: ‘dvb_usbv2_media_device_register’ defined but not used [-Wunused-function]
static void dvb_usbv2_media_device_register(struct dvb_usb_adapter *adap)
drivers/media/usb/dvb-usb/dvb-usb-dvb.c:97:13: warning: ‘dvb_usb_media_device_register’ defined but not used [-Wunused-function]
static void dvb_usb_media_device_register(struct dvb_usb_adapter *adap)
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using media_dev argument for dvb_create_media_graph(),
use the adapter.
That allows to create a stub for this function, if compiled
without DVB support, avoiding to add extra if's at the drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of assuming just one adapter, change the code to store
one media controller per adapter.
This works fine for dvb-usb, as, on all drivers here, it is not
possible to write a media graph that would mix resources between
the two different adapters.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Create a struct media_device and add it to the dvb adapter.
Please notice that the tuner is not mapped yet by the dvb core.
[mchehab@osg.samsung.com: use config option MEDIA_CONTROLLER_DVB]
Signed-off-by: Rafael Lourenço de Lima Chehab <chehabrafael@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of assuming just one adapter, change the code to store
one media controller per adapter.
This works fine for dvb-usb, as, on all drivers here, it is not
possible to write a media graph that would mix resources between
the two different adapters.
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Create a struct media_device and add it to the dvb adapter.
Please notice that the tuner is not mapped yet by the dvb core.
[mchehab@osg.samsung.com: use config option MEDIA_CONTROLLER_DVB due to a rebase]
Signed-off-by: Rafael Lourenço de Lima Chehab <chehabrafael@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need to initialize the media controller earlier, as the core
will call the smsdvb hotplug during register time. Ok, this is
an async operation, so, when the module is not loaded, the media
controller works.
However, if the module is already loaded, nothing will be
registered at the media controller, as it will load too late.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Right now, this is a debug message, misplaced. Promote it
to an info message, as it helps to discover if something
bad happened during device init.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All siano modules have a sms_dbg parameter. Now that we're using
the standard pr_debug() macro, we can get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On most cases, sms_info() should actually be pr_debug(), but,
on other places, it should be pr_info().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There's no reason to use a macro here. Just replace everything,
and let those debug messages to be activated via dynamic printk.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Despite its name, those functions are acutally debug
prints for the IR part of the driver. So, properly
map them using pr_debug()
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Originally, sms_err() would be also displaying the line where
the error occurs, but the messages are clear enough. Also,
the function is always printed. So, no need for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There's no reason for a sms' own sms_warn macro. Just replace
it by the standard pr_warn().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of defining its own set of printk functions, let's
use the common Kernel debug logic provided by pr_foo functions.
As a first step, let's just define the existing macros as the
Kernel ones.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adding support for the media controller for a pure DVB device
is simple: just create a struct media_device and add it to the
dvb adapter. After creating all DVB devices, we need to call
the DVB core, for it to create the media graph.
More work is needed for pure DVB tuners, but this is hidden
at the Siano driver, just like several others non-hybrid
devices. So, this is streight forward.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use an enum to better document the media pads.
No functional changes.
Suggested-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There's no need to free state, as it was allocated via devm_kzalloc().
Also, let's return the error code, instead of something else.
Reported-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
buf_prepare callback is called for every queued buffer. This is
an overkill. Call it at buf_setup, as this should be enough.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are two problems at the comment:
- it is badly idented;
- its comment doesn't mean anything.
Fix it.
Requested-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Analog video inputs are the tuner, plus composite, svideo, etc,
e. g. the input pat should actually be like:
___________
TUNER --------> | |
| |
SVIDEO .......> | cx25840 |
| |
COMPOSITE1 ...> |_________|
(in the above, dashes represent the enabled link, and periods
represent the disabled ones)
In other words, if we want to properly represent the pipeline,
it should be possible to see via the media controller if the tuner
is being used as an image source, or if the source is something else.
I didn't map those other inputs here yet, due to a few things:
- The extra inputs would require subdevs that won't be controlled
- I was in doubt about the best way for doing that
- That would likely require some extra setup for cx25840 caller
drivers, in order to represent what of the possible internal
inputs are actually used on each specific board
Actually, at least for now, I was unable to see much benefit
on adding such map now, so let's just document it, as this could
be added later on, as needed.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Prefix all DVB media controller entities with "dvb-" and use dash
instead of underline at the names.
Requested-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/usb/cx231xx/cx231xx-cards.c: In function ‘cx231xx_usb_probe’:
drivers/media/usb/cx231xx/cx231xx-cards.c:1589:15: error: ‘struct v4l2_device’ has no member named ‘mdev’
dev->v4l2_dev.mdev = dev->media_dev;
^
drivers/media/usb/cx231xx/cx231xx-cards.c:1589:26: error: ‘struct cx231xx’ has no member named ‘media_dev’
dev->v4l2_dev.mdev = dev->media_dev;
^
scripts/Makefile.build:257: recipe for target 'drivers/media/usb/cx231xx/cx231xx-cards.o' failed
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
if CONFIG_MEDIA_CONTROLLER_DVB is not selected, it is now
producing this warning:
drivers/media/dvb-core/dvb_frontend.c: In function ‘dvb_frontend_thread’:
drivers/media/dvb-core/dvb_frontend.c:695:6: warning: unused variable ‘ret’ [-Wunused-variable]
int ret;
^
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The logic there tries to start the media entity even if it
doesn't exist, causing this bug:
[ 314.356162] BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
[ 314.356202] IP: [<ffffffffa02ef74c>] media_entity_pipeline_start+0x1c/0x390 [media]
Reported-by: Gert-Jan van der Stroom <gjstroom@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU6pFJAAoJEHm+PkMAQRiG2OwH/24nDK+l9zkaRs0xJsVh+qiW
8A2N1od0ickz43iMk48jfeWGkFOkd4izyvan/daJshJOE1Y5lCdSs7jq/OXVOv9L
G0+KQUoC5NL0hqYKn1XJPFluNQ1yqMvrDwQt99grDGzruNGBbwHuBhAQmgzpj1nU
do8KrGjr7ft1Rzm4mOAdET/ExWiF+mRSJSxxOv598HbsIRdM5wgn0hHjPlqDxmLN
KH4r3YYEm0cHyjf4Krse0+YdhqdamRGJlmYxJgEsYNwCoMwkmHlLTc71diseUhrg
r/VYIYQvpAA6Yvgw8rJ0N5gk/sJJig+WyyPhfQuc2bD5sbL9eO7mPnz2UP7z7ss=
=vXB6
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc1' into patchwork
Linux 34.0-rc1
* tag 'v4.0-rc1': (8947 commits)
Linux 4.0-rc1
autofs4 copy_dev_ioctl(): keep the value of ->size we'd used for allocation
procfs: fix race between symlink removals and traversals
debugfs: leave freeing a symlink body until inode eviction
Documentation/filesystems/Locking: ->get_sb() is long gone
trylock_super(): replacement for grab_super_passive()
fanotify: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
Cachefiles: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
VFS: (Scripted) Convert S_ISLNK/DIR/REG(dentry->d_inode) to d_is_*(dentry)
SELinux: Use d_is_positive() rather than testing dentry->d_inode
Smack: Use d_is_positive() rather than testing dentry->d_inode
TOMOYO: Use d_is_dir() rather than d_inode and S_ISDIR()
Apparmor: Use d_is_positive/negative() rather than testing dentry->d_inode
Apparmor: mediated_filesystem() should use dentry->d_sb not inode->i_sb
VFS: Split DCACHE_FILE_TYPE into regular and special types
VFS: Add a fallthrough flag for marking virtual dentries
VFS: Add a whiteout dentry type
VFS: Introduce inode-getting helpers for layered/unioned fs environments
kernel: make READ_ONCE() valid on const arguments
blk-throttle: check stats_cpu before reading it from sysfs
...
While the DVB thread is running, the media pipeline should be
streaming. This should prevent any attempt of using the analog
TV while digital TV is working, and vice-versa.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the dvb frontend thread starts, the tuner should be switched
to the frontend. Add a code that ensures that this will happen,
using the media controller.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For now, let's keep the DVB-specific media controller links enabled
by default. On most devices, this is fixed anyway, so no big issue.
Ok, the demux actually have dynamic links based on the filters, but
we don't represent them yet, as the media controller currently lacks
the capability of dynamically create/delete entities.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
cx231xx is simple with regards to DVB: all boards have just one
DVB adapter. So, we can use the default DVB helper function to
create the DVB media graph.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need to create a DVB graph, linking the several DVB devnodes.
Add such function. Please notice that this helper function
doesn't take into account devices with multiple DVB adapters
and frontends.
For devices with multiple adapters, they should either create two
different media controller instances or to improve this function
to take the adapter ID into account.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While on some devices the tuner is bound inside the frontend,
other devices use a separate subdevice for it.
So, in order to be more generic, better to map it with two
pads.
That will allows to use the media controller to lock the tuner
between the DVB and the V4L2 sub-drivers, on hybrid devices.
While here, change the logic to use pad 0 as sink for devices
with both sink and source pads.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that we have entities and pads, let's create media links
between them, for analog setup.
We may not have all the links for digital yet, as the dvb extention
may not be loaded yet.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of keeping the media controller entity not initialized,
fill it and create the pads for cx25840.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Properly initialize tuner core subdev at the media controller.
That requires a new subtype at the media controller API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
