commit 98a04c7ace upstream.
Root decoder granularity must match value from CFWMS, which may not
be the region's granularity for non-interleaved root decoders.
So when calculating granularities for host bridge decoders, use the
region's granularity instead of the root decoder's granularity to ensure
the correct granularities are set for the host bridge decoders and any
downstream switch decoders.
Test configuration is 1 host bridge * 2 switches * 2 endpoints per switch.
Region created with 2048 granularity using following command line:
cxl create-region -m -d decoder0.0 -w 4 mem0 mem2 mem1 mem3 \
-g 2048 -s 2048M
Use "cxl list -PDE | grep granularity" to get a view of the granularity
set at each level of the topology.
Before this patch:
"interleave_granularity":2048,
"interleave_granularity":2048,
"interleave_granularity":512,
"interleave_granularity":2048,
"interleave_granularity":2048,
"interleave_granularity":512,
"interleave_granularity":256,
After:
"interleave_granularity":2048,
"interleave_granularity":2048,
"interleave_granularity":4096,
"interleave_granularity":2048,
"interleave_granularity":2048,
"interleave_granularity":4096,
"interleave_granularity":2048,
Fixes: 27b3f8d138 ("cxl/region: Program target lists")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jim Harris <jim.harris@samsung.com>
Link: https://lore.kernel.org/r/169824893473.1403938.16110924262989774582.stgit@bgt-140510-bm03.eng.stellus.in
[djbw: fixup the prebuilt cxl_test region]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9aaeef113c upstream.
master side report:
silvaco-i3c-master 44330000.i3c-master: Error condition: MSTATUS 0x020090c7, MERRWARN 0x00100000
BIT 20: TIMEOUT error
The module has stalled too long in a frame. This happens when:
- The TX FIFO or RX FIFO is not handled and the bus is stuck in the
middle of a message,
- No STOP was issued and between messages,
- IBI manual is used and no decision was made.
The maximum stall period is 100 μs.
This can be considered as being just a warning as the system IRQ latency
can easily be greater than 100us.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-7-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfd7cd6aaf upstream.
Upon IBIWON timeout, the SDA line will always be kept low if we don't emit
a stop. Calling svc_i3c_master_emit_stop() there will let the bus return to
idle state.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-6-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c85e209b79 upstream.
MSTATUS[RXPEND] is only updated after the data transfer cycle started. This
creates an issue when the I3C clock is slow, and the CPU is running fast
enough that MSTATUS[RXPEND] may not be updated when the code reaches
checking point. As a result, mandatory data can be missed.
Add a wait for MSTATUS[COMPLETE] to ensure that all mandatory data is
already in FIFO. It also works without mandatory data.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-4-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e5e3c92e7 upstream.
┌─────┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┌─────
SCL: ┘ └─────┛ └──┛ └──┛ └──┛ └──┛ └──┛ └──┛ └──┛ └──┘
───┐ ┌─────┐ ┌─────┐ ┌───────────┐
SDA: └───────────────────────┘ └─────┘ └─────┘ └─────
xxx╱ ╲╱ ╲╱ ╲╱ ╲╱ ╲
: xxx╲IBI ╱╲ Addr(0x0a) ╱╲ RW ╱╲NACK╱╲ S ╱
If an In-Band Interrupt (IBI) occurs and IBI work thread is not immediately
scheduled, when svc_i3c_master_priv_xfers() initiates the I3C transfer and
attempts to send address 0x7e, the target interprets it as an
IBI handler and returns the target address 0x0a.
However, svc_i3c_master_priv_xfers() does not handle this case and proceeds
with other transfers, resulting in incorrect data being returned.
Add IBIWON check in svc_i3c_master_xfer(). In case this situation occurs,
return a failure to the driver.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-3-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bf3fc2681 upstream.
The ibi work thread operates asynchronously with other transfers, such as
svc_i3c_master_priv_xfers(). Introduce mutex protection to ensure the
completion of the entire i3c/i2c transaction.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-2-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0718588c7a upstream.
Commit 5e42bcbc3f ("cxl/region: decrement ->nr_targets on error in
cxl_region_attach()") tried to avoid 'eiw' initialization errors when
->nr_targets exceeded 16, by just decrementing ->nr_targets when
cxl_region_setup_targets() failed.
Commit 86987c7662 ("cxl/region: Cleanup target list on attach error")
extended that cleanup to also clear cxled->pos and p->targets[pos]. The
initialization error was incidentally fixed separately by:
Commit 8d42854257 ("cxl/region: Fix port setup uninitialized variable
warnings") which was merged a few days after 5e42bcbc3f.
But now the original cleanup when cxl_region_setup_targets() fails
prevents endpoint and switch decoder resources from being reused:
1) the cleanup does not set the decoder's region to NULL, which results
in future dpa_size_store() calls returning -EBUSY
2) the decoder is not properly freed, which results in future commit
errors associated with the upstream switch
Now that the initialization errors were fixed separately, the proper
cleanup for this case is to just return immediately. Then the resources
associated with this target get cleanup up as normal when the failed
region is deleted.
The ->nr_targets decrement in the error case also helped prevent
a p->targets[] array overflow, so add a new check to prevent against
that overflow.
Tested by trying to create an invalid region for a 2 switch * 2 endpoint
topology, and then following up with creating a valid region.
Fixes: 5e42bcbc3f ("cxl/region: decrement ->nr_targets on error in cxl_region_attach()")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jim Harris <jim.harris@samsung.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/169703589120.1202031.14696100866518083806.stgit@bgt-140510-bm03.eng.stellus.in
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 565fe15062 upstream.
Currently the offset into the device when looking for OTP
bits can go outside of the address of the MTD NOR devices,
and if that memory isn't readable, bad things happen
on the IXP4xx (added prints that illustrate the problem before
the crash):
cfi_intelext_otp_walk walk OTP on chip 0 start at reg_prot_offset 0x00000100
ixp4xx_copy_from copy from 0x00000100 to 0xc880dd78
cfi_intelext_otp_walk walk OTP on chip 0 start at reg_prot_offset 0x12000000
ixp4xx_copy_from copy from 0x12000000 to 0xc880dd78
8<--- cut here ---
Unable to handle kernel paging request at virtual address db000000
[db000000] *pgd=00000000
(...)
This happens in this case because the IXP4xx is big endian and
the 32- and 16-bit fields in the struct cfi_intelext_otpinfo are not
properly byteswapped. Compare to how the code in read_pri_intelext()
byteswaps the fields in struct cfi_pri_intelext.
Adding a small byte swapping loop for the OTP in read_pri_intelext()
and the crash goes away.
The problem went unnoticed for many years until I enabled
CONFIG_MTD_OTP on the IXP4xx as well, triggering the bug.
Cc: stable@vger.kernel.org
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231020-mtd-otp-byteswap-v4-1-0d132c06aa9d@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0da668333f upstream.
Defining a prctl flag as an int is a footgun because on a 64 bit machine
and with a variadic implementation of prctl (like in musl and glibc), when
used directly as a prctl argument, it can get casted to long with garbage
upper bits which would result in unexpected behaviors.
This patch changes the constant to an unsigned long to eliminate that
possibilities. This does not break UAPI.
I think that a stable backport would be "nice to have": to reduce the
chances that users build binaries that could end up with garbage bits in
their MDWE prctl arguments. We are not aware of anyone having yet
encountered this corner case with MDWE prctls but a backport would reduce
the likelihood it happens, since this sort of issues has happened with
other prctls. But If this is perceived as a backporting burden, I suppose
we could also live without a stable backport.
Link: https://lkml.kernel.org/r/20230828150858.393570-5-revest@chromium.org
Fixes: b507808ebc ("mm: implement memory-deny-write-execute as a prctl")
Signed-off-by: Florent Revest <revest@chromium.org>
Suggested-by: Alexey Izbyshev <izbyshev@ispras.ru>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Ayush Jain <ayush.jain3@amd.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Joey Gouly <joey.gouly@arm.com>
Cc: KP Singh <kpsingh@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Szabolcs Nagy <Szabolcs.Nagy@arm.com>
Cc: Topi Miettinen <toiwoton@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1640a0ef80 upstream.
When dealing with hugetlb pages, manipulating struct page pointers
directly can get to wrong struct page, since struct page is not guaranteed
to be contiguous on SPARSEMEM without VMEMMAP. Use pfn calculation to
handle it properly.
Without the fix, a wrong number of page might be skipped. Since skip cannot be
negative, scan_movable_page() will end early and might miss a movable page with
-ENOENT. This might fail offline_pages(). No bug is reported. The fix comes
from code inspection.
Link: https://lkml.kernel.org/r/20230913201248.452081-4-zi.yan@sent.com
Fixes: eeb0efd071 ("mm,memory_hotplug: fix scan_movable_pages() for gigantic hugepages")
Signed-off-by: Zi Yan <ziy@nvidia.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 426056efe8 upstream.
When dealing with hugetlb pages, manipulating struct page pointers
directly can get to wrong struct page, since struct page is not guaranteed
to be contiguous on SPARSEMEM without VMEMMAP. Use nth_page() to handle
it properly.
A wrong or non-existing page might be tried to be grabbed, either
leading to a non freeable page or kernel memory access errors. No bug
is reported. It comes from code inspection.
Link: https://lkml.kernel.org/r/20230913201248.452081-3-zi.yan@sent.com
Fixes: 57a196a584 ("hugetlb: simplify hugetlb handling in follow_page_mask")
Signed-off-by: Zi Yan <ziy@nvidia.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e7cfe5cd5 upstream.
Patch series "Use nth_page() in place of direct struct page manipulation",
v3.
On SPARSEMEM without VMEMMAP, struct page is not guaranteed to be
contiguous, since each memory section's memmap might be allocated
independently. hugetlb pages can go beyond a memory section size, thus
direct struct page manipulation on hugetlb pages/subpages might give wrong
struct page. Kernel provides nth_page() to do the manipulation properly.
Use that whenever code can see hugetlb pages.
This patch (of 5):
When dealing with hugetlb pages, manipulating struct page pointers
directly can get to wrong struct page, since struct page is not guaranteed
to be contiguous on SPARSEMEM without VMEMMAP. Use nth_page() to handle
it properly.
Without the fix, page_kasan_tag_reset() could reset wrong page tags,
causing a wrong kasan result. No related bug is reported. The fix
comes from code inspection.
Link: https://lkml.kernel.org/r/20230913201248.452081-1-zi.yan@sent.com
Link: https://lkml.kernel.org/r/20230913201248.452081-2-zi.yan@sent.com
Fixes: 2813b9c029 ("kasan, mm, arm64: tag non slab memory allocated via pagealloc")
Signed-off-by: Zi Yan <ziy@nvidia.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44d9304524 upstream.
If the cmma no-dat feature is available the kernel page tables are walked
to identify and mark all pages which are used for address translation (all
region, segment, and page tables). In a subsequent loop all other pages are
marked as "no-dat" pages with the ESSA instruction.
This information is visible to the hypervisor, so that the hypervisor can
optimize purging of guest TLB entries. The initial loop however is
incorrect: only the first three of the four pages which belong to segment
and region tables will be marked as being used for DAT. The last page is
incorrectly marked as no-dat.
This can result in incorrect guest TLB flushes.
Fix this by simply marking all four pages.
Cc: <stable@vger.kernel.org>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1954da4a2b upstream.
If the cmma no-dat feature is available all pages that are not used for
dynamic address translation are marked as "no-dat" with the ESSA
instruction. This information is visible to the hypervisor, so that the
hypervisor can optimize purging of guest TLB entries. This also means that
pages which are used for dynamic address translation must not be marked as
"no-dat", since the hypervisor may then incorrectly not purge guest TLB
entries.
Region, segment, and page tables allocated within the gmap code are
incorrectly marked as "no-dat", since an explicit call to
arch_set_page_dat() is missing, which would remove the "no-dat" mark.
In order to fix this add a new gmap_alloc_crst() function which should
be used to allocate region and segment tables, and which also calls
arch_set_page_dat().
Also add the arch_set_page_dat() call to page_table_alloc_pgste().
Cc: <stable@vger.kernel.org>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09cda0a400 upstream.
If the cmma no-dat feature is available all pages that are not used for
dynamic address translation are marked as "no-dat" with the ESSA
instruction. This information is visible to the hypervisor, so that the
hypervisor can optimize purging of guest TLB entries. This also means that
pages which are used for dynamic address translation must not be marked as
"no-dat", since the hypervisor may then incorrectly not purge guest TLB
entries.
Region and segment tables allocated via vmem_crst_alloc() are incorrectly
marked as "no-dat", as soon as slab_is_available() returns true.
Such tables are allocated e.g. when kernel page tables are split, memory is
hotplugged, or a DCSS segment is loaded.
Fix this by adding the missing arch_set_page_dat() call.
Cc: <stable@vger.kernel.org>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03f25d53b1 upstream.
In case of the prep descriptor while the channel is already running, the
CCR register value stored into the channel could already have its EN bit
set. This would lead to a bad transfer since, at start transfer time,
enabling the channel while other registers aren't yet properly set.
To avoid this, ensure to mask the CCR_EN bit when storing the ccr value
into the mdma channel structure.
Fixes: a4ffb13c89 ("dmaengine: Add STM32 MDMA driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Cc: stable@vger.kernel.org
Tested-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/20231009082450.452877-1-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63ba2d07b4 upstream.
chameleon_parse_gdd() may fail for different reasons and end up
in the err tag. Make sure we at least always free the mcb_device
allocated with mcb_alloc_dev().
If mcb_device_register() fails, make sure to give up the reference
in the same place the device was added.
Fixes: 728ac33892 ("mcb: mcb-parse: fix error handing in chameleon_parse_gdd()")
Cc: stable <stable@kernel.org>
Reviewed-by: Jose Javier Rodriguez Barbarin <JoseJavier.Rodriguez@duagon.com>
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Link: https://lore.kernel.org/r/20231019141434.57971-2-jorge.sanjuangarcia@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e84dc3792 upstream.
This commit fixes a bug in commit 9ed9895370 ("driver core: Functional
dependencies tracking support") where the device link status was
incorrectly updated in the driver unbind path before all the device's
resources were released.
Fixes: 9ed9895370 ("driver core: Functional dependencies tracking support")
Cc: stable <stable@kernel.org>
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Closes: https://lore.kernel.org/all/20231014161721.f4iqyroddkcyoefo@pengutronix.de/
Signed-off-by: Saravana Kannan <saravanak@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Matti Vaittinen <mazziesaccount@gmail.com>
Cc: James Clark <james.clark@arm.com>
Acked-by: "Rafael J. Wysocki" <rafael@kernel.org>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231018013851.3303928-1-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f7969bcd6 upstream.
A synthetic event is created by the synthetic event interface that can
read both user or kernel address memory. In reality, it reads any
arbitrary memory location from within the kernel. If the address space is
in USER (where CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE is set) then
it uses strncpy_from_user_nofault() to copy strings otherwise it uses
strncpy_from_kernel_nofault().
But since both functions use the same variable there's no annotation to
what that variable is (ie. __user). This makes sparse complain.
Quiet sparse by typecasting the strncpy_from_user_nofault() variable to
a __user pointer.
Link: https://lore.kernel.org/linux-trace-kernel/20231031151033.73c42e23@gandalf.local.home
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Fixes: 0934ae9977 ("tracing: Fix reading strings from synthetic events");
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202311010013.fm8WTxa5-lkp@intel.com/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc7f04dc23 upstream.
When execute the following command to test clone3 under !CONFIG_TIME_NS:
# make headers && cd tools/testing/selftests/clone3 && make && ./clone3
we can see the following error info:
# [7538] Trying clone3() with flags 0x80 (size 0)
# Invalid argument - Failed to create new process
# [7538] clone3() with flags says: -22 expected 0
not ok 18 [7538] Result (-22) is different than expected (0)
...
# Totals: pass:18 fail:1 xfail:0 xpass:0 skip:0 error:0
This is because if CONFIG_TIME_NS is not set, but the flag
CLONE_NEWTIME (0x80) is used to clone a time namespace, it
will return -EINVAL in copy_time_ns().
If kernel does not support CONFIG_TIME_NS, /proc/self/ns/time
will be not exist, and then we should skip clone3() test with
CLONE_NEWTIME.
With this patch under !CONFIG_TIME_NS:
# make headers && cd tools/testing/selftests/clone3 && make && ./clone3
...
# Time namespaces are not supported
ok 18 # SKIP Skipping clone3() with CLONE_NEWTIME
...
# Totals: pass:18 fail:0 xfail:0 xpass:0 skip:1 error:0
Link: https://lkml.kernel.org/r/1689066814-13295-1-git-send-email-yangtiezhu@loongson.cn
Fixes: 515bddf0ec ("selftests/clone3: test clone3 with CLONE_NEWTIME")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa49c90894 upstream.
Since bae1d3a05a, i2c transfers are non-atomic if preemption is
disabled. However, non-atomic i2c transfers require preemption (e.g. in
wait_for_completion() while waiting for the DMA).
panic() calls preempt_disable_notrace() before calling
emergency_restart(). Therefore, if an i2c device is used for the
restart, the xfer should be atomic. This avoids warnings like:
[ 12.667612] WARNING: CPU: 1 PID: 1 at kernel/rcu/tree_plugin.h:318 rcu_note_context_switch+0x33c/0x6b0
[ 12.676926] Voluntary context switch within RCU read-side critical section!
...
[ 12.742376] schedule_timeout from wait_for_completion_timeout+0x90/0x114
[ 12.749179] wait_for_completion_timeout from tegra_i2c_wait_completion+0x40/0x70
...
[ 12.994527] atomic_notifier_call_chain from machine_restart+0x34/0x58
[ 13.001050] machine_restart from panic+0x2a8/0x32c
Use !preemptible() instead, which is basically the same check as
pre-v5.2.
Fixes: bae1d3a05a ("i2c: core: remove use of in_atomic()")
Cc: stable@vger.kernel.org # v5.2+
Suggested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Link: https://lore.kernel.org/r/20230327-tegra-pmic-reboot-v7-2-18699d5dcd76@skidata.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa5fe31b6b upstream.
__flush_dcache_pages() is called during hugetlb migration via
migrate_pages() -> migrate_hugetlbs() -> unmap_and_move_huge_page() ->
move_to_new_folio() -> flush_dcache_folio(). And with hugetlb and without
sparsemem vmemmap, struct page is not guaranteed to be contiguous beyond a
section. Use nth_page() instead.
Without the fix, a wrong address might be used for data cache page flush.
No bug is reported. The fix comes from code inspection.
Link: https://lkml.kernel.org/r/20230913201248.452081-6-zi.yan@sent.com
Fixes: 15fa3e8e32 ("mips: implement the new page table range API")
Signed-off-by: Zi Yan <ziy@nvidia.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8db0ec791f upstream.
When dealing with hugetlb pages, struct page is not guaranteed to be
contiguous on SPARSEMEM without VMEMMAP. Use nth_page() to handle it
properly.
Without the fix, a wrong subpage might be checked for HWPoison, causing wrong
number of bytes of a page copied to user space. No bug is reported. The fix
comes from code inspection.
Link: https://lkml.kernel.org/r/20230913201248.452081-5-zi.yan@sent.com
Fixes: 38c1ddbde6 ("hugetlbfs: improve read HWPOISON hugepage")
Signed-off-by: Zi Yan <ziy@nvidia.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6620999f0d upstream.
vmap_area does not exist on no-MMU, therefore the GDB scripts fail to
load:
Traceback (most recent call last):
File "<...>/vmlinux-gdb.py", line 51, in <module>
import linux.vmalloc
File "<...>/scripts/gdb/linux/vmalloc.py", line 14, in <module>
vmap_area_ptr_type = vmap_area_type.get_type().pointer()
^^^^^^^^^^^^^^^^^^^^^^^^^
File "<...>/scripts/gdb/linux/utils.py", line 28, in get_type
self._type = gdb.lookup_type(self._name)
^^^^^^^^^^^^^^^^^^^^^^^^^^^
gdb.error: No struct type named vmap_area.
To fix this, disable the command and add an informative error message if
CONFIG_MMU is not defined, following the example of lx-slabinfo.
Link: https://lkml.kernel.org/r/20231031202235.2655333-2-ben.wolsieffer@hefring.com
Fixes: 852622bf36 ("scripts/gdb/vmalloc: add vmallocinfo support")
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Kieran Bingham <kbingham@kernel.org>
Cc: Kuan-Ying Lee <Kuan-Ying.Lee@mediatek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60466c0679 upstream.
As the emergency restart does not call kernel_restart_prepare(), the
system_state stays in SYSTEM_RUNNING.
Since bae1d3a05a, this hinders i2c_in_atomic_xfer_mode() from becoming
active, and therefore might lead to avoidable warnings in the restart
handlers, e.g.:
[ 12.667612] WARNING: CPU: 1 PID: 1 at kernel/rcu/tree_plugin.h:318 rcu_note_context_switch+0x33c/0x6b0
[ 12.676926] Voluntary context switch within RCU read-side critical section!
...
[ 12.742376] schedule_timeout from wait_for_completion_timeout+0x90/0x114
[ 12.749179] wait_for_completion_timeout from tegra_i2c_wait_completion+0x40/0x70
...
[ 12.994527] atomic_notifier_call_chain from machine_restart+0x34/0x58
[ 13.001050] machine_restart from panic+0x2a8/0x32c
Avoid these by setting the correct system_state.
Fixes: bae1d3a05a ("i2c: core: remove use of in_atomic()")
Cc: stable@vger.kernel.org # v5.2+
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Link: https://lore.kernel.org/r/20230327-tegra-pmic-reboot-v7-1-18699d5dcd76@skidata.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3cc1b0be2 upstream.
Since commit d7e7b9af10 ("fscrypt: stop using keyrings subsystem for
fscrypt_master_key"), xfstest generic/270 causes a WARNING when run on
f2fs with test_dummy_encryption in the mount options:
$ kvm-xfstests -c f2fs/encrypt generic/270
[...]
WARNING: CPU: 1 PID: 2453 at fs/crypto/keyring.c:240 fscrypt_destroy_keyring+0x1f5/0x260
The cause of the WARNING is that not all encrypted inodes have been
evicted before fscrypt_destroy_keyring() is called, which violates an
assumption. This happens because the test uses an external quota file,
which gets automatically encrypted due to test_dummy_encryption.
Encryption of quota files has never really been supported. On ext4,
ext4_quota_read() does not decrypt the data, so encrypted quota files
are always considered invalid on ext4. On f2fs, f2fs_quota_read() uses
the pagecache, so trying to use an encrypted quota file gets farther,
resulting in the issue described above being possible. But this was
never intended to be possible, and there is no use case for it.
Therefore, make the quota support layer explicitly reject using
IS_ENCRYPTED inodes when quotaon is attempted.
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20230905003227.326998-1-ebiggers@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61187fce86 upstream.
JBD2 makes sure journal data is fallen on fs device by sync_blockdev(),
however, other process could intercept the EIO information from bdev's
mapping, which leads journal recovering successful even EIO occurs during
data written back to fs device.
We found this problem in our product, iscsi + multipath is chosen for block
device of ext4. Unstable network may trigger kpartx to rescan partitions in
device mapper layer. Detailed process is shown as following:
mount kpartx irq
jbd2_journal_recover
do_one_pass
memcpy(nbh->b_data, obh->b_data) // copy data to fs dev from journal
mark_buffer_dirty // mark bh dirty
vfs_read
generic_file_read_iter // dio
filemap_write_and_wait_range
__filemap_fdatawrite_range
do_writepages
block_write_full_folio
submit_bh_wbc
>> EIO occurs in disk <<
end_buffer_async_write
mark_buffer_write_io_error
mapping_set_error
set_bit(AS_EIO, &mapping->flags) // set!
filemap_check_errors
test_and_clear_bit(AS_EIO, &mapping->flags) // clear!
err2 = sync_blockdev
filemap_write_and_wait
filemap_check_errors
test_and_clear_bit(AS_EIO, &mapping->flags) // false
err2 = 0
Filesystem is mounted successfully even data from journal is failed written
into disk, and ext4/ocfs2 could become corrupted.
Fix it by comparing the wb_err state in fs block device before recovering
and after recovering.
A reproducer can be found in the kernel bugzilla referenced below.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217888
Cc: stable@vger.kernel.org
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230919012525.1783108-1-chengzhihao1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72151ad0cb upstream.
Driver compares widget name in wsa_macro_spk_boost_event() widget event
callback, however it does not handle component's name prefix. This
leads to using uninitialized stack variables as registers and register
values. Handle gracefully such case.
Fixes: 2c4066e5d4 ("ASoC: codecs: lpass-wsa-macro: add dapm widgets and route")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231003155422.801160-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f2bd7cbd1 upstream.
The USB Compact Keyboard variant requires a reset_resume function to
restore keyboard configuration after a suspend in some situations. Move
configuration normally done on probe to lenovo_features_set_cptkbd(), then
recycle this for use on reset_resume.
Without, the keyboard and driver would end up in an inconsistent state,
breaking middle-button scrolling amongst other problems, and twiddling
sysfs values wouldn't help as the middle-button mode won't be set until
the driver is reloaded.
Tested on a USB and Bluetooth Thinkpad Compact Keyboard.
CC: stable@vger.kernel.org
Fixes: 94eefa2713 ("HID: lenovo: Use native middle-button mode for compact keyboards")
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Link: https://lore.kernel.org/r/20231002150914.22101-1-martink@posteo.de
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef43c30858 upstream.
The initial value of 5% chosen for the maximum allowed percentage
difference between resctrl mbm value and IMC mbm value in
commit 06bd03a57f ("selftests/resctrl: Fix MBA/MBM results reporting
format") was "randomly chosen value" (as admitted by the changelog).
When running tests in our lab across a large number platforms, 5%
difference upper bound for success seems a bit on the low side for the
MBA and MBM tests. Some platforms produce outliers that are slightly
above that, typically 6-7%, which leads MBA/MBM test frequently
failing.
Replace the "randomly chosen value" with a success bound that is based
on those measurements across large number of platforms by relaxing the
MBA/MBM success bound to 8%. The relaxed bound removes the failures due
the frequent outliers.
Fixed commit description style error during merge:
Shuah Khan <skhan@linuxfoundation.org>
Fixes: 06bd03a57f ("selftests/resctrl: Fix MBA/MBM results reporting format")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06035f0194 upstream.
The MBA and CMT tests expect support of other features to be able to
run.
When platform only supports MBA but not MBM, MBA test will fail with:
Failed to open total bw file: No such file or directory
When platform only supports CMT but not CAT, CMT test will fail with:
Failed to open bit mask file '/sys/fs/resctrl/info/L3/cbm_mask': No such file or directory
It leads to the test reporting test fail (even if no test was run at
all).
Extend feature checks to cover these two conditions to show these tests
were skipped rather than failed.
Fixes: ee0415681e ("selftests/resctrl: Use resctrl/info for feature detection")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> # selftests/resctrl: Refactor feature check to use resource and feature name
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d56e5da0e0 upstream.
Feature check in validate_resctrl_feature_request() takes in the test
name string and maps that to what to check per test.
Pass resource and feature names to validate_resctrl_feature_request()
directly rather than deriving them from the test name inside the
function which makes the feature check easier to extend for new test
cases.
Use !! in the return statement to make the boolean conversion more
obvious even if it is not strictly necessary from correctness point of
view (to avoid it looking like the function is returning a freed
pointer).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> # selftests/resctrl: Remove duplicate feature check from CMT test
Cc: <stable@vger.kernel.org> # selftests/resctrl: Move _GNU_SOURCE define into Makefile
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a1e4a91aa upstream.
_GNU_SOURCE is defined in resctrl.h. Defining _GNU_SOURCE has a large
impact on what gets defined when including headers either before or
after it. This can result in compile failures if .c file decides to
include a standard header file before resctrl.h.
It is safer to define _GNU_SOURCE in Makefile so it is always defined
regardless of in which order includes are done.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 030b48fb2c upstream.
The test runner run_cmt_test() in resctrl_tests.c checks for CMT
feature and does not run cmt_resctrl_val() if CMT is not supported.
Then cmt_resctrl_val() also check is CMT is supported.
Remove the duplicated feature check for CMT from cmt_resctrl_val().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit beb7f47184 upstream.
signal_handler_unregister() calls sigaction() with uninitializing
sa_flags in the struct sigaction.
Make sure sa_flags is always initialized in signal_handler_unregister()
by initializing the struct sigaction when declaring it. Also add the
initialization to signal_handler_register() even if there are no know
bugs in there because correctness is then obvious from the code itself.
Fixes: 73c55fa5ab ("selftests/resctrl: Commonize the signal handler register/unregister for all tests")
Suggested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 805ce81826 upstream.
In the current setup the PA is left unmuted even when the
Soundwire ports are not started streaming. This can lead to click
and pop sounds during start.
There is a same issue in the reverse order where in the PA is
left unmute even after the data stream is stopped, the time
between data stream stopping and port closing is long enough
to accumulate DC on the line resulting in Click/Pop noise
during end of stream.
making use of new mute_unmute_on_trigger flag is helping a
lot with this Click/Pop issues reported on this Codec
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231027105747.32450-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0220575e6 upstream.
In some setups like Speaker amps which are very sensitive, ex: keeping them
unmute without actual data stream for very short duration results in a
static charge and results in pop and clicks. To minimize this, provide a way
to mute and unmute such codecs during trigger callbacks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231027105747.32450-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
[ johan: backport to v6.6.2 ]
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8837ba3e58 ]
list_for_each_entry_safe() does not work for the async case which runs
under RCU, therefore, split GC logic for catchall in two functions
instead, one for each of the sync and async GC variants.
The catchall sync GC variant never sees a _DEAD bit set on ever, thus,
this handling is removed in such case, moreover, allocate GC sync batch
via GFP_KERNEL.
Fixes: 93995bf4af ("netfilter: nf_tables: remove catchall element in GC sync path")
Reported-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93995bf4af ]
The expired catchall element is not deactivated and removed from GC sync
path. This path holds mutex so just call nft_setelem_data_deactivate()
and nft_setelem_catchall_remove() before queueing the GC work.
Fixes: 4a9e12ea7e ("netfilter: nft_set_pipapo: call nft_trans_gc_queue_sync() in catchall GC")
Reported-by: lonial con <kongln9170@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b836c4d29f upstream.
Commit 18b44bc5a6 ("ovl: Always reevaluate the file signature for
IMA") forced signature re-evaulation on every file access.
Instead of always re-evaluating the file's integrity, detect a change
to the backing file, by comparing the cached file metadata with the
backing file's metadata. Verifying just the i_version has not changed
is insufficient. In addition save and compare the i_ino and s_dev
as well.
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Tested-by: Eric Snowberg <eric.snowberg@oracle.com>
Tested-by: Raul E Rangel <rrangel@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e044374a8a upstream.
It is not clear that IMA should be nested at all, but as long is it
measures files both on overlayfs and on underlying fs, we need to
annotate the iint mutex to avoid lockdep false positives related to
IMA + overlayfs, same as overlayfs annotates the inode mutex.
Reported-and-tested-by: syzbot+b42fe626038981fb7bfa@syzkaller.appspotmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b439aaa62 upstream.
The Qualcomm SPMI PMIC revid implementation is broken in multiple ways.
First, it assumes that just because the sibling base device has been
registered that means that it is also bound to a driver, which may not
be the case (e.g. due to probe deferral or asynchronous probe). This
could trigger a NULL-pointer dereference when attempting to access the
driver data of the unbound device.
Second, it accesses driver data of a sibling device directly and without
any locking, which means that the driver data may be freed while it is
being accessed (e.g. on driver unbind).
Third, it leaks a struct device reference to the sibling device which is
looked up using the spmi_device_from_of() every time a function (child)
device is calling the revid function (e.g. on probe).
Fix this mess by reimplementing the revid lookup so that it is done only
at probe of the PMIC device; the base device fetches the revid info from
the hardware, while any secondary SPMI device fetches the information
from the base device and caches it so that it can be accessed safely
from its children. If the base device has not been probed yet then probe
of a secondary device is deferred.
Fixes: e9c11c6e3a ("mfd: qcom-spmi-pmic: expose the PMIC revid information to clients")
Cc: stable@vger.kernel.org # 6.0
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Link: https://lore.kernel.org/r/20231003152927.15000-3-johan+linaro@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0fa44c261 upstream.
The Qualcomm SPMI PMIC revid implementation is broken in multiple ways.
First, it totally ignores struct device_node reference counting and
leaks references to the parent bus node as well as each child it
iterates over using an open-coded for_each_child_of_node().
Second, it leaks references to each spmi device on the bus that it
iterates over by failing to drop the reference taken by the
spmi_device_from_of() helper.
Fix the struct device_node leaks by reimplementing the lookup using
for_each_child_of_node() and adding the missing reference count
decrements. Fix the sibling struct device leaks by dropping the
unnecessary lookups of devices with the wrong USID.
Note that this still leaves one struct device reference leak in case a
base device is found but it is not the parent of the device used for the
lookup. This will be addressed in a follow-on patch.
Fixes: e9c11c6e3a ("mfd: qcom-spmi-pmic: expose the PMIC revid information to clients")
Cc: stable@vger.kernel.org # 6.0
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Link: https://lore.kernel.org/r/20231003152927.15000-2-johan+linaro@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 259e33cbb1 upstream.
GCC 13.2 complains about array subscript 17 is above array bounds of
'char[16]' with IFNAMSIZ set to 16.
The warning is correct but this scenario is impossible.
set_device_name is called by device_name_store (store sysfs entry) and
netdev_trig_activate.
device_name_store already check if size is >= of IFNAMSIZ and return
-EINVAL. (making the warning scenario impossible)
netdev_trig_activate works on already defined interface, where the name
has already been checked and should already follow the condition of
strlen() < IFNAMSIZ.
Aside from the scenario being impossible, set_device_name can be
improved to both mute the warning and make the function safer.
To make it safer, move size check from device_name_store directly to
set_device_name and prevent any out of bounds scenario.
Cc: stable@vger.kernel.org
Fixes: 28a6a2ef18 ("leds: trigger: netdev: refactor code setting device name")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309192035.GTJEEbem-lkp@intel.com/
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20231007131042.15032-1-ansuelsmth@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fe8508e2b upstream.
SMEM uses lock index 3 of the TCSR Mutex hwlock for allocations
in SMEM region shared by the Host and FW.
Fix the SMEM hwlock index to 3 for IPQ9574.
Cc: stable@vger.kernel.org
Fixes: 46384ac7a6 ("arm64: dts: qcom: ipq9574: Add SMEM support")
Signed-off-by: Vignesh Viswanathan <quic_viswanat@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230904172516.479866-5-quic_viswanat@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3337a6fea2 upstream.
Per the "SMC calling convention specification", the 64-bit calling
convention can only be used when the client is 64-bit. Whereas the
32-bit calling convention can be used by either a 32-bit or a 64-bit
client.
Currently during SCM probe, irrespective of the client, 64-bit calling
convention is made, which is incorrect and may lead to the undefined
behaviour when the client is 32-bit. Let's fix it.
Cc: stable@vger.kernel.org
Fixes: 9a434cee77 ("firmware: qcom_scm: Dynamically support SMCCC and legacy conventions")
Reviewed-By: Elliot Berman <quic_eberman@quicinc.com>
Signed-off-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Link: https://lore.kernel.org/r/20230925-scm-v3-1-8790dff6a749@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
