The CEC 32K AO Clock is a dual divider with dual counter to provide a more
precise 32768Hz clock for the CEC subsystem from the external xtal.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Switch the aoclk driver to use the new bindings and switch all the
registers access to regmap only.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Input source 0 of the mmc controllers is not directly xtal, as currently
described in DT. Each controller is fed by a composite clock (the usual
mux, divider and gate). The muxes inputs are the xtal (default) and the
fclk_div clocks. These parents, along with the divider, should be able to
provide the necessary rates for mmc and nand operation.
The input muxes should also be able to take mpll2, mpll3 and gp0_pll but
these are precious clocks, needed for other usage. It is better if the
mmc does not use these them. For this reason, mpll2, mpll3 and gp0_pll is
not listed among the possible parents.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
CLK_DIVIDER_ROUND_CLOSEST was incorrectly put in the hw.init flags
while it should have been in the divider flags
Fixes: 3c277c247e ("clk: meson: gxbb: add cts_mclk_i958")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
CLK_DIVIDER_ROUND_CLOSEST was incorrectly put in the hw.init flags
while it should have been in the divider flags
Fixes: 4087bd4b21 ("clk: meson: gxbb: add cts_amclk")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The clock controller also includes some reset lines. This patch
implements a reset controller to assert and de-assert these resets.
The reset controller itself is registered early (through
CLK_OF_DECLARE_DRIVER) because it is needed very early in the boot
process (to start the secondary CPU cores).
According to the public S805 datasheet there are two more reset bits
in the HHI_SYS_CPU_CLK_CNTL0 register, which are not implemented by
this patch (as these seem to be unused in Amlogic's vendor Linux kernel
sources and their u-boot tree):
- bit 15: GEN_DIV_SOFT_RESET
- bit 14: SOFT_RESET
All information was taken from the public S805 Datasheet and Amlogic's
vendor GPL kernel sources. This patch is based on an earlier version
submitted by Carlo Caione.
Suggested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the clkids for the clocks feeding the input0 of the mmc controllers
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Expose all clocks which maybe used as DT bindings
Only clock ids internal the controller remain un-exposed
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Expose all clocks which maybe used as DT bindings
Only clock ids internal the controller remain un-exposed (none on this
particular controller at the moment)
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
gxbb clock driver gracefully handles case where the clkid is defined but
the clock hw pointer is not provided, as long as it is not at the end of
the hw_onecell_data array.
This patch ensure that the last entries are defined as well to handle
this particular case.
Fixes: a70c6e06ed ("clk: meson: gxbb: protect against holes in the onecell_data array")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
meson8b clock driver gracefully handles case where the clkid is defined
but the clock hw pointer is not provided, as long as it is not at the end
of the hw_onecell_data array.
This patch ensure that the last entries are defined as well to handle
this particular case.
Fixes: e92f7cca44 ("clk: meson8b: clean up fixed rate clocks")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The CPUX clock, which is the main clock of the ARM core on Allwinner H3,
can be adjusted by changing the frequency of the PLL_CPUX clock.
Allowing setting parent clock for the CPUX clock, thus the PLL_CPUX
clock can be adjusted when adjusting the CPUX clock.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Fixes: 0577e4853b ("clk: sunxi-ng: Add H3 clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This patch utilizes the new PLL clk notifier to gate then ungate the
PLL CPU clock after rate changes. This should prevent any system hangs
resulting from cpufreq changes to the clk.
Reported-by: Ondrej Jirman <megous@megous.com>
Fixes: 0577e4853b ("clk: sunxi-ng: Add H3 clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
This SoC is too old. It is difficult to maintain any longer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently a bug in the sci_clk_get implementation causes it to always
return a clock belonging to the last device in the static list of clock
data. This is due to a bug in the init code that causes the array
used by sci_clk_get to only be populated with the clocks for the last
device, as each device overwrites the entire array with its own clocks.
Fix this by calculating the actual number of clocks for the SoC, and
allocating the whole array in one go. Also, we don't need the handle
to the init data array anymore after doing this, instead we can
just compare the dev_id / clk_id against the registered clocks and
use binary search for speed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Dave Gerlach <d-gerlach@ti.com>
Fixes: b745c0794e ("clk: keystone: Add sci-clk driver support")
Cc: Nishanth Menon <nm@ti.com>
Tested-by: Franklin Cooper <fcooper@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
One critical clock fix for sun5i (A10s/A13/R8) which enables propogation
of clock rate changes from the "cpu" clock to it's parent PLL clock.
This fixes cpufreq related crashes that have been observed on KernelCI
with the C.H.I.P. and multi_v7_defconfig.
-----BEGIN PGP SIGNATURE-----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=uoCy
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-fixes-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Pull one Allwinner clock fix from Chen-Yu Tsai:
One critical clock fix for sun5i (A10s/A13/R8) which enables propagation
of clock rate changes from the "cpu" clock to it's parent PLL clock.
This fixes cpufreq related crashes that have been observed on KernelCI
with the C.H.I.P. and multi_v7_defconfig.
* tag 'sunxi-clk-fixes-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: sun5i: Add clk_set_rate_parent to the CPU clock
mpll0 clock is special compared to the other mplls. It needs another
bit (ssen) to be set to activate the fractional part the mpll divider
Fixes: 007e6e5c5f ("clk: meson: mpll: add rw operation")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Currently ccu_frac_helper_set_rate() doesn't wait for a lock bit to be
set before returning. Because of that, unstable clock may be used.
Add a wait for lock in the helper function.
Fixes: 89a3dfb787 ("clk: sunxi-ng: Add fractional lib")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
ccu_frac_helper_read_rate() prints some info which is not really
helpful except during debugging.
Replace printk() with pr_debug().
Fixes: 89a3dfb787 ("clk: sunxi-ng: Add fractional lib")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Driver for multiplier clock is missing a call to
ccu_frac_helper_enable() when fractional mode is selected.
Add a call to ccu_frac_helper_enable().
Fixes: d77e8135b3 ("clk: sunxi-ng: multiplier: Add fractional support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
N-M factor clock driver is missing a call to ccu_frac_helper_enable()
when fractional mode is used. Additionally, most SoCs require that M
factor must be set to 0 when fractional mode is used.
Without this patch, clock keeps the old value and clk_set_rate() returns
without error.
Fixes: 6174a1e24b ("clk: sunxi-ng: Add N-M-factor clock support")
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This patch fixes values of the EPLL K coefficient and changes
the EPLL output frequency values to match exactly what is
possible to achieve with given M, P, S, K coefficients.
This allows to avoid rounding errors and unexpected frequency
being set with clk_set_rate(), due to recalc_rate returning
different values than the PLL rate specified in the
exynos5420_epll_24mhz_tbl table. E.g. this prevents a case
where two consecutive clk_set_rate() calls with same argument
result in different PLL output frequency.
The PLL output frequencies have been calculated with formula:
f = fxtal * (M * 2^16 + K) / (P * 2^S) / 2^16
where fxtal = 24000000.
Fixes: 9842452acd ("clk: samsung: exynos542x: Add EPLL rate table")
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Remove trailing extra underscore in definition of _CCU_SUN8I_R_H
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current CPU clock is missing the option to change the rate of its
parents, leading to improper rates calculated by cpufreq, and eventually
crashes.
Cc: <stable@vger.kernel.org>
Fixes: 5e73761786 ("clk: sunxi-ng: Add sun5i CCU driver")
Reported-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: "Emilio López" <emilio@elopez.com.ar>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: James Liao <jamesjj.liao@mediatek.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Register each PLL and its division clocks to clock
lookup table to facilitate the clock look up for
clock consumer.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Clock on ls1088a chip takes primary clocking input from the external
SYSCLK signal. The SYSCLK input (frequency) is multiplied using
multiple phase locked loops (PLL) to create a variety of frequencies
which can then be passed to a variety of internal logic, including
cores and peripheral IP modules.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Do the checks for accessing the SD divider table only when the rate gets
updated, namely on init and set_rate. In all other cases, reuse the last
value. This simplifies code, runtime load, and error reporting.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
'rate' is not used, so we can use 'parent_rate' directly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Read the enable register to determine if the clock is already in use by
the firmware. In this case avoid gating the clock.
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Fixes: 282a4e4ce5 ("platform/x86: Enable Atom PMC platform clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Drop static on a local variable, when the variable is initialized before
any possible use. Thus, the static has no benefit.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Remove unnecessary static on local variable _base_ in both functions
moxart_of_pll_clk_init() and moxart_of_apb_clk_init(). Such variables
are initialized before being used, on every execution path throughout
the mentioned functions. The statics have no benefit and, removing
them reduce the code size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see the difference in the code size. Also,
notice that the bss segment is reduced down to zero. This log is the
output of the size command, before and after the code change:
before:
text data bss dec hex filename
1724 384 128 2236 8bc drivers/clk/clk-moxart.o
after:
text data bss dec hex filename
1697 240 0 1937 791 drivers/clk/clk-moxart.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
As there is no way to actually query the hardware for the current clock
rate, now racalc_rate() just returns the last rate that was previously
set. But if the rate was not set yet, we return the bogus rate of 1000Hz.
The branch clocks have the same rate as their parent, so in this case we
just need to remove recalc_rate ops and then the core framework will handle
this automagically. The round_rate() is unused, so remove it as well.
Reported-by: Archit Taneja <architt@codeaurora.org>
Fixes: 00f64b5887 ("clk: qcom: Add support for SMD-RPM Clocks")
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fixed the signedness bug returning '(-22)' on the return type as u8 with
removing the sanity checker in clk_cpumux_get_parent() since
clk_cpumux_set_parent() always ensures validity in clk_cpumux_get_parent()
got called.
Fixes: 1e17de9049 ("clk: mediatek: add missing cpu mux causing Mediatek cpufreq can't work")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
commit e2860e1f62 ("serial: 8250_of: Add reset support")
introduced reset support for the 8250_of driver.
However it unconditionally uses the assert/deassert pair to
deassert reset on the device at probe and assert it at
remove. This does not work with systems that have a
self-deasserting reset controller, such as Gemini, that
recently added a reset controller.
As a result, the console will not probe on the Gemini with
this message:
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
of_serial: probe of 42000000.serial failed with error -524
This (-ENOTSUPP) is the error code returned by the
deassert() operation on self-deasserting reset controllers.
To work around this, implement dummy .assert() and
.deassert() operations in the Gemini combined clock and
reset controller. This fixes the issue on this system.
Cc: Joel Stanley <joel@jms.id.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-serial@vger.kernel.org
Fixes: e2860e1f62 ("serial: 8250_of: Add reset support")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Update IDT VersaClock 5 driver to support 5P49V5925. This chip has only
external clock input, four fractional dividers (FODs) and five clock
outputs (four universal clock outputs and one reference clock output at
OUT0_SELB_I2C).
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Update IDT VersaClock 5 driver to support IDT VersaClock 6 5P49V6901.
This chip has two clock inputs (external XTAL or external CLKIN), four
fractional dividers (FODs) and five clock outputs (four universal clock
outputs and one reference clock output at OUT0_SELB_I2C).
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
on Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The VersaClock 6 has an input frequency doubler between the input
clock mux and the predivider. Add new capability flag and support
for this frequency doubler block into the driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
on Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Split the VC5 clock input mux and the predivider to more accurately
model the hardware and fix the previously incorrect assumption that
both the OUT_SEL_I2CB and the PLL are fed from the predivider.
It is in fact the clock input mux output which is directly feeding
the clock into the OUT_SEL_I2CB output, while the clock input mux
output first passes through the predivider before it is fed into
the PLL.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
on Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The output buffer input mux can be configured in either of three
states -- disabled, input from FOD, input from previous output.
Once the .prepare() callback of the output buffer is called, the
output buffer input mux must be set to either input from FOD or
input from previous output, it cannot be set to Disabled anymore
or the output won't work.
Default to the input from FOD if the output buffer input mux was
Disabled and the .prepare() was called on it.
Note that we do not set the output buffer input mux back to Disabled
in the .unprepare() callback as there is no obvious benefit of doing
so. We disable the entire output buffer in the .unprepare() callback
already.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The output buffer input mux can be configured in either of three
states -- disabled, input from FOD, input from previous output.
If the output buffer input mux is set to disabled, the code in
vc5_clk_out_get_parent() would consider this an invalid setting
and warn about it, which is not necessarily the case.
In case the output buffer input mux is disabled, default to input
from FOD to have some parent and don't print the warning.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In case the initial values of the FOD registers are not configured in
the OTP or by the bootloader, it is possible that the FOD registers
will contain zeroes. The code in vc5_fod_recalc_rate() immediately
feeds the FOD divider value obtained from the FOD registers into the
div64_u64() and if the FOD divider value is zero, triggers division
by zero exception.
Check if the FOD divider value is zero and return the frequency of
the FOD output as 0 Hz if it is so. This prevents the division by
zero exception.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
AXS10X boards manages it's clocks using various PLLs. These PLL has same
dividers and corresponding control registers mapped to different addresses.
So we add one common driver for such PLLs.
Each PLL on AXS10X board consist of three dividers: IDIV, FBDIV and
ODIV. Output clock value is managed using these dividers.
We add pre-defined tables with supported rate values and appropriate
configurations of IDIV, FBDIV and ODIV for each value.
As of today we add support for PLLs that generate clock for the
following devices:
* ARC core on AXC CPU tiles.
* ARC PGU on ARC SDP Mainboard.
and more to come later.
By this patch we add support for two plls (arc core pll and pgu pll),
so we had to use two different init types: CLK_OF_DECLARE for arc core pll and
regular probing for pgu pll.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
[sboyd@codeaurora.org: Silence dubious !x & y sparse warning,
make of_axs10x_pll_clk_setup() unregister clk on failure]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Enable compile-testing of the remaining clock drivers and subdrivers,
now dummies are available for of_clk_get_from_provider(),
of_device_compatible_match(), and rcar_rst_read_mode_pins(), and the
CPG/MSSR driver core has been converted from of_match_node() to
of_device_get_match_data().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the missing documentation for the fields in struct div6_clock
related to parent selection for DIV6 clocks with selectable parents, as
found in R/SH-Mobile SoCs.
Fixes: c6d67fb037 ("clk: shmobile: div6: support selectable-input clocks")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Pull MIPS updates from Ralf Baechle:
"Boston platform support:
- Document DT bindings
- Add CLK driver for board clocks
CM:
- Avoid per-core locking with CM3 & higher
- WARN on attempt to lock invalid VP, not BUG
CPS:
- Select CONFIG_SYS_SUPPORTS_SCHED_SMT for MIPSr6
- Prevent multi-core with dcache aliasing
- Handle cores not powering down more gracefully
- Handle spurious VP starts more gracefully
DSP:
- Add lwx & lhx missaligned access support
eBPF:
- Add MIPS support along with many supporting change to add the
required infrastructure
Generic arch code:
- Misc sysmips MIPS_ATOMIC_SET fixes
- Drop duplicate HAVE_SYSCALL_TRACEPOINTS
- Negate error syscall return in trace
- Correct forced syscall errors
- Traced negative syscalls should return -ENOSYS
- Allow samples/bpf/tracex5 to access syscall arguments for sane
traces
- Cleanup from old Kconfig options in defconfigs
- Fix PREF instruction usage by memcpy for MIPS R6
- Fix various special cases in the FPU eulation
- Fix some special cases in MIPS16e2 support
- Fix MIPS I ISA /proc/cpuinfo reporting
- Sort MIPS Kconfig alphabetically
- Fix minimum alignment requirement of IRQ stack as required by
ABI / GCC
- Fix special cases in the module loader
- Perform post-DMA cache flushes on systems with MAARs
- Probe the I6500 CPU
- Cleanup cmpxchg and add support for 1 and 2 byte operations
- Use queued read/write locks (qrwlock)
- Use queued spinlocks (qspinlock)
- Add CPU shared FTLB feature detection
- Handle tlbex-tlbp race condition
- Allow storing pgd in C0_CONTEXT for MIPSr6
- Use current_cpu_type() in m4kc_tlbp_war()
- Support Boston in the generic kernel
Generic platform:
- yamon-dt: Pull YAMON DT shim code out of SEAD-3 board
- yamon-dt: Support > 256MB of RAM
- yamon-dt: Use serial* rather than uart* aliases
- Abstract FDT fixup application
- Set RTC_ALWAYS_BCD to 0
- Add a MAINTAINERS entry
core kernel:
- qspinlock.c: include linux/prefetch.h
Loongson 3:
- Add support
Perf:
- Add I6500 support
SEAD-3:
- Remove GIC timer from DT
- Set interrupt-parent per-device, not at root node
- Fix GIC interrupt specifiers
SMP:
- Skip IPI setup if we only have a single CPU
VDSO:
- Make comment match reality
- Improvements to time code in VDSO"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (86 commits)
locking/qspinlock: Include linux/prefetch.h
MIPS: Fix MIPS I ISA /proc/cpuinfo reporting
MIPS: Fix minimum alignment requirement of IRQ stack
MIPS: generic: Support MIPS Boston development boards
MIPS: DTS: img: Don't attempt to build-in all .dtb files
clk: boston: Add a driver for MIPS Boston board clocks
dt-bindings: Document img,boston-clock binding
MIPS: Traced negative syscalls should return -ENOSYS
MIPS: Correct forced syscall errors
MIPS: Negate error syscall return in trace
MIPS: Drop duplicate HAVE_SYSCALL_TRACEPOINTS select
MIPS16e2: Provide feature overrides for non-MIPS16 systems
MIPS: MIPS16e2: Report ASE presence in /proc/cpuinfo
MIPS: MIPS16e2: Subdecode extended LWSP/SWSP instructions
MIPS: MIPS16e2: Identify ASE presence
MIPS: VDSO: Fix a mismatch between comment and preprocessor constant
MIPS: VDSO: Add implementation of gettimeofday() fallback
MIPS: VDSO: Add implementation of clock_gettime() fallback
MIPS: VDSO: Fix conversions in do_monotonic()/do_monotonic_coarse()
MIPS: Use current_cpu_type() in m4kc_tlbp_war()
...
Add a driver for the clocks provided by the MIPS Boston board from
Imagination Technologies. 2 clocks are provided - the system clock & the
CPU clock - and each is a simple fixed rate clock whose frequency can be
determined by reading a register provided by the board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16483/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The probe does a shift and mask of val without having read it from the hardware.
Fixes: 846423f967 ("clk: Add Gemini SoC clock controller")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Current implementation of scpi_clk_add just print a warning when clock
fails to register but then keep going as if nothing happened. The
provider is then registered with bogus data.
This may latter lead to an Oops in __clk_create_clk when
hlist_add_head(&clk->clks_node, &hw->core->clks) is called.
This patch fixes the issue and errors if a clock fails to register.
Fixes: cd52c2a4b5 ("clk: add support for clocks provided by SCP(System Control Processor)")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
On sama5d2, VDD core maybe be cut while in suspend. This means registers
will be lost. Ensure they are saved and restored properly.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
CONFIG_COMPILE_TEST allows building a configuration without
TI_SCI_PROTOCOL, which then fails to link:
drivers/clk/keystone/sci-clk.o: In function `ti_sci_clk_probe':
sci-clk.c:(.text.ti_sci_clk_probe+0x4c): undefined reference to `devm_ti_sci_get_handle'
This makes it a hard dependency. Right now, that means we can't
actually compile-test the driver unless ARCH_KEYSTONE is set as
well, but we can fix that by allowing TI_MESSAGE_MANAGER to
be selected for COMPILE_TEST as well.
Fixes: b745c0794e ("clk: keystone: Add sci-clk driver support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Similarly to commit f1e9203e23 ("clk: samsung: Fix Exynos 5420 pinctrl
setup and clock disable failure due to domain being gated") for
Exynos5420, the Exynos4412 also requires that EPLL is not disabled.
Otherwise any access to MAUDIO block will silently halt.
This was not visible before because EPLL on Exynos4 could not be
disabled before commit 6edfa11cb3 ("clk: samsung:
Add enable/disable operation for PLL36XX clocks"). After this commit,
on Odroid U3 board one can see silent hang, usually with last (but
unrelated) messages:
[ 2.382741] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[ 2.405686] usb 1-3: new high-speed USB device number 3 using exynos-ehci
[ 2.419843] max77686-rtc max77686-rtc: setting system clock to 2017-06-21 17:04:13 UTC (1498064653)
Mark Exynos4 variant as also needed EPLL to be enabled all the time.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This allows the NAND driver to get the clock rate via clk_get_rate().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The Cortina Systems Gemini (SL3516/CS3516) has an on-chip clock
controller that derive all clocks from a single crystal, using some
documented and some undocumented PLLs, half dividers, counters and
gates. This is a best attempt to construct a clock driver for the
clocks so at least we can gate off unused hardware and driver the
PCI bus clock.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[sboyd@codeaurora.org: Fix devm_ioremap_resource() return value
checking]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that this function is called from driver probe routines, it
needs to drop the __init marking because it isn't just called
from init code.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Cc: Anup Patel <anup.patel@broadcom.com>
Cc: Ray Jui <ray.jui@broadcom.com>
Cc: Scott Branden <scott.branden@broadcom.com>
Fixes: 654cdd3229 ("clk: bcm: Add clocks for Stingray SOC")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds support for Stingray clocks in iproc
ccf. The Stingray SOC has various plls based on iproc
pll architecture.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The patch enables CPU multiplexer clock on MT8173 SoC which fixes up
cpufreq driver fails at acquiring intermediate clock source when driver
probe is called.
Signed-off-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The patch enables CPU multiplexer clock on MT2701/MT7623 SoC which fixes
up cpufreq driver fails at acquiring intermediate clock source when driver
probe is called.
Signed-off-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds CPU multiplexer clocks which are essential for Mediatek
cpufreq driver. It would use the CPU clock multiplexer to switch to the
intermediate clock source temporarily and then wait for the primary clock
changing getting stable.
Signed-off-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If CONFIG_OF=n:
drivers/clk/renesas/renesas-cpg-mssr.c: In function ‘cpg_mssr_probe’:
drivers/clk/renesas/renesas-cpg-mssr.c:702: warning: dereferencing ‘void *’ pointer
drivers/clk/renesas/renesas-cpg-mssr.c:702: error: request for member ‘data’ in something not a structure or union
To fix this, use the of_device_get_match_data() helper, for which a
dummy version is provided if CONFIG_OF=n.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Export I2S mux clocks, so that device tree can refer to them for setting
a better parent clock for I2S work clock.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The rawnand clock gate gates two clocks, NAND_USDHC_BUS_CLK_ROOT
and NAND_CLK_ROOT. However, the gate has been in the chain of the
latter only. This does not allow to use the NAND_USDHC_BUS_CLK_ROOT
only, e.g. as required by APBH-Bridge-DMA.
Add new clocks which represent the clock after the gate, and use a
shared clock gate to correctly model the hardware.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Set PPLL2 to 2880M. With this patch, we saw better compatibility
on various 1080p HDMI monitors.
Signed-off-by: Zhong Kaihua <zhongkaihua@huawei.com>
Signed-off-by: Zheng Shaobo <zhengshaobo1@huawei.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
[sboyd@codeaurora.org: Add UL to long number to silence C90
warning]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Parent name of clk_mux_sysbus is not correct. This patch fixes it.
Signed-off-by: Chen Jun <chenjun14@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
MCLK for internal audio codec is expected to be at 9.6MHz by default.
This patch adds support to 9.6MHz to make the default case possible.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds support for the global clock controller found on
the ipq8074 based devices. This includes UART, I2C, SPI etc.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Mark an array of strings static const and remove the dereference
of a function pointer when assigning to the platform driver probe
struct member.
drivers/clk/mvebu/cp110-system-controller.c:89:12:
warning: symbol 'gate_base_names' was not declared. Should it be static?
drivers/clk/mvebu/cp110-system-controller.c:447:18:
error: cannot dereference this type
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Pull improved Marvel Armada 7K/8K cp110 clk support from Gregory CLEMENT:
We got more information about the clock controllers and the clock tree
of the CP110 part that we find in the Marvell Armada 7K/8K SoCs. The
clk driver is modified accordingly from this new information.
* 'clk-cp110' of git://git.infradead.org/linux-mvebu:
clk: mvebu: cp110: add sdio clock to cp-110 system controller
clk: mvebu: cp110: introduce a new binding
clk: mvebu: cp110: do not depend anymore of the *-clock-output-names
clk: mvebu: cp110: make failure labels more meaningful
The smplsel bits for the SDMMC clock on Arria10 and Stratix10 platforms are
offset by 1 additional bit.
Add a new macro SYSMGR_SDMMC_CTRL_SET_AS10 for usage on the Arria10 and
Stratix10 platforms.
Fixes: 5611a5ba8e ("clk: socfpga: update clk.h so for Arria10 platform to use")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The timer will register into system at very early phase at kernel boot;
if timer needs to use clock, the clock should be get ready in function
of_clk_init() so later the timer driver probe can retrieve clock
successfully. This is finished in below flow on arm64:
start_kernel()
`-> time_init()
`-> of_clk_init(NULL) => register timer's clock
`-> clocksource_probe() => register timer
On Hi3660 the sp804 timer uses clock "osc32k", this clock is registered
as platform driver rather than CLK_OF_DECLARE_DRIVER method. As result,
sp804 timer probe returns failure due if cannot bind clock properly.
To fix the failure, this patch is to split crgctrl clocks into two
subsets. One part is for fixed_rate_clks which includes pre-defined
fixed rate clocks, and "osc32k" clock is in this category; So we change
their registration to CLK_OF_DECLARE_DRIVER method, as result the clocks
can be registered ahead with function of_clk_init() and timer driver can
bind timer clock successfully; the rest of the crgctrl clocks are still
registered by the probe of the platform driver.
This patch also adds checking for all crgctrl clocks registration and
print out log if any clock has failure.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This commit updates the CP110 system controller driver to add the
definition for a missing clock.
The SDIO clock is dedicated driving the SDHCI interface and its frequency
is 400MHz (2/5 of PLL source clock).
The SDIO interface should be bound to this clock and not the core clock
as in the older code.
Using the wrong clock lead to a maximum SDHCI frequency of 250 Mhz, while
the HW really supports up to 400 Mhz.
This patch also fixes the NAND clock relationship documentation.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
[gregory.clement@free-electrons.com:
- use sdio instead of emmc to name the clock]
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The initial intent when the binding of the cp110 system controller was to
have one flat node. The idea being that what is currently a clock-only
driver in drivers would become a MFD driver, exposing the clock, GPIO and
pinctrl functionality. However, after taking a step back, this would lead
to a messy binding. Indeed, a single node would be a GPIO controller,
clock controller, pinmux controller, and more.
This patch adopts a more classical solution of a top-level syscon node
with sub-nodes for the individual devices. The main benefit will be to
have each functional block associated to its own sub-node where we can
put its own properties.
The introduction of the Armada 7K/8K is still in the early stage so the
plan is to remove the old binding. However, we don't want to break the
device tree compatibility for the few devices already in the field. For
this we still keep the support of the legacy compatible string with a big
warning in the kernel about updating the device tree.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Using the *-clock-output-names property was a convenient way to have a
unique name for each clock even when there are multiple cp110 blocks
as we can find on Armada 8K.
However it has some drawbacks: the main one being a stronger link than
necessary between the driver and the device tree. For example the clock
name can't be changed, removed or moved. It is still the early stage of
introduction of the Armada 7K/8K and the hardware is still not totally
documented, especially for the clock part. By removing the use of
*-clock-output-names it will be easier to add new clocks without breaking
the compatibility.
The name of each clock is now created by using its physical address as a
prefix (as it was done for the platform device names). Thanks to this we
have an automatic way to compute a unique name.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
* Add new compatible to the meson8 clock controller for meson8b
* Add missing parents to gxbb clk81
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=0BO9
-----END PGP SIGNATURE-----
Merge tag 'meson-clk-for-4.13-2' of git://github.com/BayLibre/clk-meson into clk-next
Pull Amlogic clk driver updates from Jerome Brunet:
* Expose more clock gate on meson8 (SAR ADC, RNG, USB, SDIO, ETH)
* Add new compatible to the meson8 clock controller for meson8b
* Add missing parents to gxbb clk81
* tag 'meson-clk-for-4.13-2' of git://github.com/BayLibre/clk-meson:
clk: meson: gxbb: add all clk81 parents
clk: meson: meson8b: add compatibles for Meson8 and Meson8m2
clk: meson8b: export the ethernet gate clock
clk: meson8b: export the USB clocks
clk: meson8b: export the gate clock for the HW random number generator
clk: meson8b: export the SDIO clock
clk: meson8b: export the SAR ADC clocks
Some new clock units are supported, for the display clocks unsed in the
newer SoCs, and the A83T PRCM.
There is also a bunch of minor fixes for clocks that are not used by
anyone, and reworks needed by drivers that will land in 4.13.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZQY1YAAoJEBx+YmzsjxAgaqkQAIzXNo0oo/M+WWl2BiDBywQT
saAaquvpFBagelEYA7tN7hkVmbUdemZoYGSjK/FmOxWKDDGYuUphZboBiQ+UGdqf
5EMS0V+OLjA0EVviBIMm9g1hotPx/RJOyVHW1Whi4HwRwCRHbK7t2wZgZi1Df1+p
OPSeW+oPPEOOf8V4wI89sh2FXvqF/xY/dRUZKWA/GJNOia7tk3rxCTTA6TMl8W0M
hBQFMKqzIfruUMIgpKx305Rc5wpZbFz7Vc/XlZCwnmtr3UTHqaQp953LLm5VHUS5
EfbEibYRcy9ZBFLjciIJofyfO9V7mMrpkEqACG/C64gu4qbxi110mH6grUjGQtxC
CWStTtwVCHIl16dZe0e0WsxR/ZpXH/Q9DlHmshCGlQxz2d6YKqpimo5ZygIrw6uD
/TiFvqfoWowwGdI7ghA7FrRHHPW8HCiL7oEft+K06G4kgEo4YN74xI+xcyuAYDph
z/GLXgJVVOE34iFsd2rndYm857OsaEmyL1XG7NBbnW/g6U4OnhI3aC7JrrEqXdKu
iFMp80kWymoCujyWnabB7dKQbtuFxiqrCZ6OkqP+VE83Ux5JWQagumunhgr1OTUB
VJL4PVgaP5lCV74PtUmj/H1HaaQwWxr20xaHI2yOOmCxF7jlWbISjuQI1zb3lyKu
v9qczQNze3OiLPY14RpW
=41iN
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-next
Pull Allwinner clock patches from Maxime Ripard:
Some new clock units are supported, for the display clocks unsed in the
newer SoCs, and the A83T PRCM.
There is also a bunch of minor fixes for clocks that are not used by
anyone, and reworks needed by drivers that will land in 4.13.
* tag 'sunxi-clk-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (21 commits)
clk: sunxi-ng: Move all clock types to a library
clk: sunxi-ng: a83t: Add support for A83T's PRCM
dt-bindings: clock: sunxi-ccu: Add compatible string for A83T PRCM
clk: sunxi-ng: select SUNXI_CCU_MULT for sun8i-a83t
clk: sunxi-ng: a83t: Fix audio PLL divider offset
clk: sunxi-ng: a83t: Fix PLL lock status register offset
clk: sunxi-ng: Add driver for A83T CCU
clk: sunxi-ng: Support multiple variable pre-dividers
dt-bindings: clock: sunxi-ccu: Add compatible string for A83T CCU
clk: sunxi-ng: de2: fix wrong pointer passed to PTR_ERR()
clk: sunxi-ng: sun5i: Export video PLLs
clk: sunxi-ng: mux: Re-adjust parent rate
clk: sunxi-ng: mux: Change pre-divider application function prototype
clk: sunxi-ng: mux: split out the pre-divider computation code
clk: sunxi-ng: mux: Don't just rely on the parent for CLK_SET_RATE_PARENT
clk: sunxi-ng: div: Switch to divider_round_rate
clk: sunxi-ng: Pass the parent and a pointer to the clocks round rate
clk: divider: Make divider_round_rate take the parent clock
clk: sunxi-ng: explicitly include linux/spinlock.h
clk: sunxi-ng: add support for DE2 CCU
...
Remove the FIXME on clk81 mux and add all the documented parents
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add data for omap4 clkctrl clocks, and register it within the clkctrl
driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Previously, hwmod core has been used for controlling the hwmod level
clocks directly. This has certain drawbacks, like being unable to share
the clocks for multiple users, missing usecounting and generally being
totally incompatible with the common clock framework.
This patch adds support for clkctrl clocks for addressing the above
issues. These support the modulemode handling, which will replace the
direct hwmod clkctrl linkage. Any optional clocks are also supported,
gate, mux and divider.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Some fixes that fix some bindings that went in 4.12, fix a few reset and
clock offsets and a build error fix
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZQYutAAoJEBx+YmzsjxAglWMQALkuMBskgMNE78L9M3kgNoOs
e44VWQLI0K0fOHyrnG1Y8wGy8pzTFXVhk13M8eJM9ELeVwN2hnwplcwooxt/I/Og
9B95qjDFSD4yTsE0SdcyT2KB6NXX6qrh/Wv5Q4ixi1vr09DGZ52jdbug+h0fLZxM
e1akTgv6oIQRdr1S4WykxnDDhNvooNV9Qgn4zKObwP2euTuRlllhPt+dj8rvgJzh
z23m6b296MbYh0hb2t0uqocQwkyOVHa9rtdCTVJFPaOeb+kjxl5NuFZzG/hrBRUm
+LbXwy0acst5SAdDDPGEYTnxyREB+vVYKF22i2+jSf3vTxRWZrZQkPlSs+0LtMLZ
LtLPUIdwFWdps/kY1IFjt0UeBw6mnv3LCv1dSciazRZDKexvzrWaNEZ942oS0Iqw
N7tltUEf4UJFZsgCY+yY+C4WL0QXsWtmVKFJDYtr2/yhgC1SpDNZP20DomwVMZ6G
i7SP+5uyCf7TNRXvckTfz3q0747f1V0yD9a0vR/cR5+TCmKChLIUava95/07qvy8
+AbSz9g2n7sKZTn+z3UUDuln9XTXGcy29SXigSXneeiFV1tjHUssZueLPvb/4EA9
LlNMr2JWG7Ois6H655512K6fvMUlqNvWpbdfnB45raPLU7AGa1xc95QXo7fMcfo/
6wxUN+7nhPDO8AXZmc7w
=G33o
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-fixes-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Allwinner clock fixes for 4.12
Some fixes that fix some bindings that went in 4.12, fix a few reset and
clock offsets and a build error fix
* tag 'sunxi-clk-fixes-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: a64: Export PLL_PERIPH0 clock for the PRCM
clk: sunxi-ng: h3: Export PLL_PERIPH0 clock for the PRCM
dt-bindings: clock: sunxi-ccu: Add pll-periph to PRCM's needed clocks
clk: sunxi-ng: enable SUNXI_CCU_MP for PRCM
clk: sunxi-ng: v3s: Fix usb otg device reset bit
clk: sunxi-ng: a31: Correct lcd1-ch1 clock register offset
- conversion to the clk_hw API
- definitions and fixes of exynos5420 SoC audio subsystem
related clocks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2bgV
-----END PGP SIGNATURE-----
Merge tag 'clk-v4.13-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk into clk-next
Pull samsung clk driver updates from Sylwester Nawrocki
- conversion to the clk_hw API
- definitions and fixes of exynos5420 SoC audio subsystem
related clocks
* tag 'clk-v4.13-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk:
clk: samsung: exynos542x: Add EPLL rate table
clk: samsung: Add missing exynos5420 audio related clocks
clk: samsung: Add enable/disable operation for PLL36XX clocks
clk: samsung: s5pv210-audss: Convert to the new clk_hw API
clk: samsung: exynos-clkout: Convert to the new clk_hw API
clk: samsung: exynos-audss: Convert to the new clk_hw API
clk: samsung: Convert common drivers to the new clk_hw API
clk: samsung: Add local variable to match its purpose
clk: samsung: Remove dead code
table and the usual bunch of some new clock-ids and some clocks marked as
critical.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlk5xMgQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgQhdCACyqXbTUEGQDaqKa40f0IPOQCPZ31XYuz8t
3kQRV08ZkBQlI0tAKgxS4+tTERtpWBA3PjIlnZQ/VRogQsiJpWj6//98Z8jJ9oEx
2lsKTw3XAb/BVsvW4Awi7VbStt5LNxRxwuIU4uXgHaapTi7wQrqAlam+2iXNOW7h
05/piVKlKOyS52009UeiO3bzFojiTlElC1JQPqnVA65KxqhYvb/9rt3hn8Y8ZqF1
KuLibE/AC5eDX7XaCFe+a7dbJpA6b+ciHg24jk+BMuksy53yYbngLbDwlOs7YFjo
PjFgbdsJw25uE2i0ZwtarAOJoLOtBJiSNib6FJCmC6yHLy5Sc8l/
=kKnC
-----END PGP SIGNATURE-----
Merge tag 'v4.13-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull rockchip clk driver updates from Heiko Stuebner:
One new clock controller for the rk3128 soc, a fixup for the rk3228 cpuclk
table and the usual bunch of some new clock-ids and some clocks marked as
critical.
* tag 'v4.13-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: mark some special clk as critical on rk3368
clk: rockchip: mark noc and some special clk as critical on rk3288
clk: rockchip: mark noc and some special clk as critical on rk3228
clk: rockchip: mark pclk_ddrupctl as critical_clock on rk3036
clk: rockchip: add clock controller for rk3128
dt-bindings: add bindings for rk3128 clock controller
clk: rockchip: export more rk3228 clocks ids
clk: rockchip: add ids for rk3399 testclks used for camera handling
clk: rockchip: add dt-binding header for rk3128
clk: rockchip: fix up the RK3228 clk cpu setting table
clk: rockchip: add clock-ids for more rk3228 clocks
clk: rockchip: add ids for camera on rk3399
In K2G, the clock handling is done through firmware executing on a
separate core. Linux kernel needs to communicate to the firmware
through TI system control interface to access any power management
related resources, including clocks.
The keystone sci-clk driver does this, by communicating to the
firmware through the TI SCI driver. The driver adds support for
registering clocks through DT, and basic required clock operations
like prepare/get_rate, etc.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[sboyd@codeaurora.org: Make ti_sci_init_clocks() static]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clock controller on Meson8, Meson8b and Meson8m2 is very similar
based on the code from the Amlogic GPL kernel sources. Add separate
compatibles for each SoC to make sure that we can easily implement
all the small differences for each SoC later on.
In general the Meson8 and Meson8m2 seem to be almost identical as they
even share the same mach-meson8 directory in Amlogic's GPL kernel
sources.
The main clocks on Meson8, Meson8b and Meson8m2 are very similar,
because they are all using the same PLL values, 90% of the clock gates
are the same (the actual diffstat of the mach-meson8/clock.c and
mach-meson8b/clock.c files is around 30 to 40 lines, when excluding
all commented out code).
The difference between the Meson8 and Meson8b clock gates seem to be:
- Meson8 has AIU_PCLK, HDMI_RX, VCLK2_ENCT, VCLK2_ENCL, UART3,
CSI_DIG_CLKIN gates which don't seem to be available on Meson8b
- the gate on Meson8 for bit 7 seems to be named "_1200XXX" instead
of "PERIPHS_TOP" (on Meson8b)
- Meson8b has a SANA gate which doesn't seem to exist on Meson8 (or
on Meson8 the same bit is used by the UART3 gate in Amlogic's GPL
kernel sources)
None of these gates is added for now, since it's unclear whether these
definitions are actually correct (the VCLK2_ENCT gate for example is
defined, but only used in some commented block).
The main difference between all three SoCs seem to be the video (VPU)
clocks. Apart from different supported clock rates (according to vpu.c
in mach-meson8 and mach-meson8b from Amlogic's GPL kernel sources) the
most notable difference is that Meson8m2 has a GP_PLL clock and a mux
(probably the same as on the Meson GX SoCs) to support glitch-free
(clock rate) switching.
None of these VPU clocks are not supported by our mainline meson8b
clock driver yet though.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Export the ethernet gate clock to the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Export the USB related clocks (for the USB controller and the USB2 PHYs)
so they can be used in the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This exports the clock so it can be used in the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Export the SDIO clock so it can be used in the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Export the clocks for the SAR ADC so they can be used in the
dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
A specific clock rate table is added for EPLL so it is possible
to set frequency of the EPLL output clock as multiple of various
audio sampling rates.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds missing definitions of mux clocks required for using
EPLL as the audio subsystem root clock on exynos5420/exynos5422 SoCs.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The existing enable/disable ops for PLL35XX are made more generic
and used also for PLL36XX. This fixes issues in the kernel with
PLL36XX PLLs when the PLL has not been already enabled by bootloader.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Clock providers should use the new struct clk_hw based API, so convert
Samsung S5PV210 Audio Subsystem clock provider to the new approach.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Clock providers should use the new struct clk_hw based API, so convert
Exynos CLKOUT clock provider to the new approach.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Clock providers should use the new struct clk_hw based API, so convert
Exynos Audio Subsystem clock provider to the new approach.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Clock providers should use the new struct clk_hw based API, so convert
Samsung clock providers and their helper functions to the new approach.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Add new variable to avoid using clk pointer for different purposes across
the exynos_register_cpu_clock() function. This will help in future rewrite
for the new clk_hw API.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
samsung_clk_register_pll2550x() function is not used anymore,
so remove its declaration.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
We've run into kconfig missing dependency errors in the sunxi-ng
code a couple times now. Each time the fix is to find the missing
select statement and add it to the Kconfig entry for a particular
SoC driver. Given that all this code is builtin (non-modular) we
don't need to do this complicated dependency tracking in Kconfig.
Instead we can move all the "library"ish code to be compiled as
lib-y instead of obj-y, let the linker throw away unused code in
the resulting vmlinux, and drop all the Kconfig stuff we use to
track clock types.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[Maxime: added lib.a to obj-y, added the comment]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T's PRCM has the same set of clocks and resets as the A64.
However, a few dividers are different. And due to the lack of a low
speed 32.768 kHz oscillator, a few of the clock parents are different.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We get a link error when CCU_MULT is not set with the
newly added driver:
drivers/clk/sunxi-ng/ccu-sun8i-a83t.o:(.data.__compound_literal.1+0x4): undefined reference to `ccu_mult_ops'
drivers/clk/sunxi-ng/ccu-sun8i-a83t.o:(.data.__compound_literal.3+0x4): undefined reference to `ccu_mult_ops'
Fixes: 46b492116666 ("clk: sunxi-ng: Add driver for A83T CCU")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The divider of the audio PLL has an offset of 1.
Fix this in the driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The offset for the PLL lock status register was incorrectly set to
0x208, which actually points to an unused register. The correct
register offset is 0x20c.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T clock control unit is a hybrid of some new style clock designs
from the A80, and old style layout from the other Allwinner SoCs.
Like the A80, the SoC does not have a low speed 32.768 kHz oscillator.
Unlike the A80, there is no clock input either. The only low speed clock
available is the internal oscillator which runs at around 16 MHz,
divided by 512, yielding a low speed clock around 31.250 kHz.
Also, the MMC2 module clock supports switching to a "new timing" mode.
This mode divides the clock output by half, and disables the CCU based
clock delays. The MMC controller must be configure to the same mode,
and then use its internal clock delays.
This driver does not support runtime switching of the timing modes.
Instead, the new timing mode is enforced at probe time. Consumers can
check which mode is active by trying to get the current phase delay
of the MMC2 phase clocks, which will return -ENOTSUPP if the new
timing mode is active.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A83T, the AHB1 clock has a shared pre-divider on the two
PLL-PERIPH clock parents. To support such instances of shared
pre-dividers, this patch extends the mux clock type to support
multiple variable pre-dividers.
As the pre-dividers are only used to calculate the rate, but
do not participate in the factorization process, this is fairly
straightforward.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
PTR_ERR should access the value just tested by IS_ERR, otherwise
the wrong error code will be returned.
Fixes: b0d9a4bd52bd ("clk: sunxi-ng: add support for DE2 CCU")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The video PLLs are used directly by the HDMI controller. Export them so
that we can use them in our DT node.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Currently, the parent rate given back to the clock framework in our
request is the original parent rate we calculated before trying to round
the rate of our clock.
This works fine unless our clock also changes its parent rate, in which
case we will simply ignore that change and still use the previous parent
rate.
Create a new function to re-adjust the parent rate to take the pre-dividers
into account, and give that back to the clock framework.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The current function name is a bit confusing, and doesn't really allow to
create an explicit function to reverse the operation.
We also for now change the parent rate through a pointer, while we don't
return anything.
In order to be less confusing, and easier to use for downstream users,
change the function name to something hopefully clearer, and return the
adjusted rate instead of changing the pointer.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The pre-divider retrieval code was merged into the function to apply the
current pre-divider onto the parent clock rate so that we can use that
adjusted value to do our factors computation.
However, since we'll need to do the reverse operation, we need to split out
that code into a function that will be shared.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The current code only rely on the parent to change its rate in the case
where CLK_SET_RATE_PARENT is set.
However, some clock rates might be obtained only through a modification of
the parent and the clock divider. Just rely on the round rate of the clocks
to give us the best computation that might be achieved for a given rate.
round_rate functions now need to honor CLK_SET_RATE_PARENT, but either the
functions already do that if they modify the parent, or don't modify the
praents at all.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
divider_round_rate_parent already evaluates changing the parent rate if
CLK_SET_RATE_PARENT is set. Now that we can do that on muxes too, let's
just use it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The clocks might need to modify their parent clocks. In order to make that
possible, give them access to the parent clock being evaluated, and to a
pointer to the parent rate so that they can modify it if needed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
So far, divider_round_rate only considers the parent clock returned by
clk_hw_get_parent.
This works fine on clocks that have a single parents, this doesn't work on
muxes, since we will only consider the first parent, while other parents
may totally be able to provide a better combination.
Clocks in that case cannot use divider_round_rate, so would have to come up
with a very similar logic to work around it. Instead of having to do
something like this, and duplicate that logic everywhere, create a
divider_round_rate parent to allow caller to give an additional parameter
for the parent clock to consider.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
ccu_reset.h and ccu_reset.c use spinlock_t and associated functions but
rely on implict inclusion of linux/spinlock.h which means that changes
in other headers could break the build. Thus, add an explicit include.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The "Display Engine 2.0" in Allwinner newer SoCs contains a clock
management unit for its subunits, like the DE CCU in A80.
Add a sunxi-ng style driver for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit ad14972422 ("clk: imx7d: Fix the powerdown bit location
of PLL DDR") used the incorrect bit for the IMX_PLLV3_DDR_IMX7 case.
Fix it accordingly to avoid a kernel hang.
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The old RealView clock implementation is not used anymore
(nothing in the kernel calls realview_clk_init()) as we have
moved all clocks over to device tree. Delete it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fractional clock dividers generate accurate average frequencies but
with jitter, particularly when the integer divisor is small.
Introduce a new metric of clock accuracy to penalise clocks with a good
average but worse jitter compared to clocks with an average which is no
better but with lower jitter. The metric is the ideal rate minus the
worse deviation from that ideal using the nearest integer divisors.
Use this metric for parent selection for clocks requiring low jitter
(currently just PCM).
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Restrict clock sources for the PCM peripheral to the oscillator and
PLLD_PER because other source may have varying rates or be switched off.
Prevent other sources from being selected by replacing their names in
the list of potential parents with dummy entries (entry index is
significant).
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If a clock has the prediv flag set, both the integer and fractional
parts must be scaled when calculating the resulting frequency.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch introduces the managed version of clk_bulk_get.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Anson Huang <anson.huang@nxp.com>
Cc: Robin Gong <yibin.gong@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: Octavian Purdila <octavian.purdila@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These helper function allows drivers to get several clk consumers in
one operation. If any of the clk cannot be acquired then any clks
that were got will be put before returning to the caller.
This can relieve the driver owners' life who needs to handle many clocks,
as well as each clock error reporting.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Anson Huang <anson.huang@nxp.com>
Cc: Robin Gong <yibin.gong@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: Octavian Purdila <octavian.purdila@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These can be marked as const * const.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* Expose more i2s and spdif output clocks
* Expose EE uart and SPICC gate clocks
* Remove cpu_clk from to gxbb
* Mark clk81 as critical on gxbb
* Add CEC EE clocks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=8rsv
-----END PGP SIGNATURE-----
Merge tag 'meson-clk-for-4.13' of git://github.com/BayLibre/clk-meson into clk-next
Pull Amlogic clock driver updates from Jerome Brunet:
* Expose more i2s and spdif output clocks
* Expose EE uart and SPICC gate clocks
* Remove cpu_clk from to gxbb
* Mark clk81 as critical on gxbb
* Add CEC EE clocks
* tag 'meson-clk-for-4.13' of git://github.com/BayLibre/clk-meson:
clk: meson-gxbb: Add EE 32K Clock for CEC
clk: gxbb: remove CLK_IGNORE_UNUSED from clk81
clk: meson: meson8b: mark clk81 as critical
clk: meson: gxbb: remove the "cpu_clk" from the GXBB and GXL driver
clk: meson-gxbb: un-export the CPU clock
clk: meson-gxbb: expose UART clocks
clk: meson-gxbb: expose SPICC gate
clk: meson-gxbb: expose spdif master clock
clk: meson-gxbb: expose i2s master clock
clk: meson-gxbb: expose spdif clock gates
Undo preparation of a clock source, if palmas_clks_init_configure is not
successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The jtag clk no driver to handle them.
But this clk need enable,so make it as critical.
The ddrphy/ddrupctl clks no driver to handle them,
Chip design requirements for these clock to always on,
The pmu_hclk_otg0 is Chip design defect, must be always on,
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The atclk/dbg/jtag/hsic-xin12m/pclk_core clks no driver to handle them.
But this clks need enable,so make it as ignore_unused for now.
The ddrupctl0/ddrupctl1/publ0/publ1 clks no driver to handle them,
Chip design requirements for these clock to always on,
The pmu_hclk_otg0 is Chip design defect, must be always on,
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The jtag/bus/peri/initmem/rom/stimer/phy clks no driver to handle them.
But this clks need enable,so make it as critical.
The ddrupctl/ddrmon/ddrphy clks no driver to handle them,
Chip design requirements for these clock to always on,
The hclk_otg_pmu is Chip design defect, must be always on,
The new document will update the description of this clock.
All these non-noc/non-arbi clocks,IC suggest always on,
Because it's have some order limitation, between the NOC clock switch
and bus IDLE(or pd on/off).
The software is not very good to solve this constraint.
Always on these clocks, has no effect on the system power consumption.
The new document will update the description of these clock.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
No driver to handle this clk yet, but chip design requiress for this clock
supplying the ddr controller to be always on.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the clock tree definition for the new rk3128 SoC.
And it also applies to the RK3126 SoC.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch exports related BUS/VPU/RGA/HDCP/IEP/TSP/WIFI/
VIO/USB/EFUSE/GPU/CRYPTO clocks for dts reference.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
clk_testout1 and clk_testout2 are used for camera handling, so add their ids.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- Add more module clocks for R-Car H3 ES2.0 and M3-W,
- Add CPG/MSSR drivers for all supported R-Car Gen2 SoCs, enabling support
for module resets, which are not supported by the existing driver,
- Rework Kconfig and Makefile logic,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=29vW
-----END PGP SIGNATURE-----
Merge tag 'clk-renesas-for-v4.13-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next
clk: renesas: Updates for v4.13
- Add more module clocks for R-Car H3 ES2.0 and M3-W,
- Add CPG/MSSR drivers for all supported R-Car Gen2 SoCs, enabling support
for module resets, which are not supported by the existing driver,
- Rework Kconfig and Makefile logic,
- Small fixes and cleanups.
In preparation to the addition of a new clock, rename the goto labels
used to handle the failure cases using a name related to the failure
cause. This will allow to insert additional failing cases without
renaming all the labels.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
When failing to set a clock the printout emitted is incorrect.
"u32 rate" is formatted as %d and should be %u whereas "unsigned long
clk_set_rate()" is formatted as %ld and should be %lu as per
Documentation/printk-formats.txt.
Fixes: 2885c3b2a3 ("clk: Show correct information when fail to set clock rate")
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The frequencies above the maximum value of signed integer(i.e. 2^31 -1)
will overflow with the current code.
This patch fixes the return type of __scpi_dvfs_round_rate from 'int'
to 'unsigned long'.
Fixes: cd52c2a4b5 ("clk: add support for clocks provided by SCP(System Control Processor)")
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
ls1012a has separate input root clocks for core PLLs versus the
platform PLL, with the latter described as sysclk in the hw docs.
If a second input clock, named "coreclk", is present, this clock will be
used for the core PLLs.
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
clk_generated_startup is called after clk_hw_register. So the first call to
get_parent will not have the correct value (i.e. 0) and because this is
cached, it may never be updated.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fixes: df70aeef60 ("clk: at91: add generated clock driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
According to the MX7D Reference Manual the powerdown bit of
CCM_ANALOG_PLL_DDRn register is bit 20, so fix it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The Linksys WRT3200ACM CPU is clocked at 1866MHz. Add 1866MHz to the
list of supported CPU frequencies. Also update multiplier and divisor
for the l2clk and ddrclk.
Noticed by the following warning:
[ 0.000000] Selected CPU frequency (16) unsupported
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
As for cp110, the initial intent when the binding of the ap806 system
controller was to have one flat node. The idea being that what is
currently a clock-only driver in drivers would become a MFD driver,
exposing the clock, GPIO and pinctrl functionality. However, after taking
a step back, this would lead to a messy binding. Indeed, a single node
would be a GPIO controller, clock controller, pinmux controller, and
more.
This patch adopts a more classical solution of a top-level syscon node
with sub-nodes for the individual devices. The main benefit will be to
have each functional block associated to its own sub-node where we can
put its own properties.
The introduction of the Armada 7K/8K is still in the early stage so the
plan is to remove the old binding. However, we don't want to break the
device tree compatibility for the few devices already in the field. For
this we still keep the support of the legacy compatible string with a big
warning in the kernel about updating the device tree.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/cc8c8c40fa4c4e71133033358992ec38e5aa2be5.1496239589.git-series.gregory.clement@free-electrons.com
As it was done for the cp110, this patch modifies the way the clock names
are created. The name of each clock is now created by using its physical
address as a prefix (as it was done for the platform device
names). Thanks to this we have an automatic way to compute a unique name.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/e66cdd54d36c6bef78460a51e577f171b6ccb031.1496239589.git-series.gregory.clement@free-electrons.com
The PRCM takes PLL_PERIPH0 as one of its parents for the AR100 clock.
As such we need to be able to describe this relationship in the device
tree.
Export the PLL_PERIPH0 clock so we can reference it in the PRCM node.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PRCM takes PLL_PERIPH0 as one of its parents for the AR100 clock.
As such we need to be able to describe this relationship in the device
tree.
Export the PLL_PERIPH0 clock so we can reference it in the PRCM node.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On Amlogic GX SoCs, there is two CEC controllers :
- An Amlogic CEC custom in the AO domain
- The Synopsys HDMI-TX Controller in the EE domain
Each of these controllers needs a 32.768KHz clock, but there is two paths :
- In the EE domain, the "32k_clk" this patchs is adding
- In the AO domain, with a more complex dual divider more precise setup
The AO 32K clock support will be pushed later in the corresponding
gxbb-aoclk driver when the AE CEC driver is ready.
The EE 32k_clk must be pushed earlier since mainline support for CEC in the
Synopsys HDMI-TX controller is nearby.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[Rebased patch on top of last changes]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
clk81 already has CLK_IS_CRITICAL so CLK_IGNORE_UNUSED is not
necessary
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Disabling clk81 results in an immediate freeze of the whole system. This
can happen "accidentally" when the last child-clock of clk81 is disabled
(in this case the common clock framework also disables clk81, even if it
was only enabled indirectly before).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
It seems that the "cpu_clk" was carried over from the meson8b clock
controller driver. On Meson GX (GXBB/GXL/GXM) the registers which are
used by the cpu_clk have a different purpose (in other words: they don't
control the CPU clock anymore). HHI_SYS_CPU_CLK_CNTL1 bits 31:24 are
reserved according to the public S905 datasheet, while bit 23 is the
"A53_trace_clk_DIS" gate (which according to the datasheet should only
be used in case a silicon bug is discovered) and bits 22:20 are a
divider (A53_trace_clk). The meson clk-cpu code however expects that
bits 28:20 are reserved for a divider (according to the public S805
datasheet this "SCALE_DIV: This value represents an N+1 divider of the
input clock.").
The CPU clock on Meson GX SoCs is provided by the SCPI DVFS clock
driver instead. Two examples from a Meson GXL S905X SoC:
- vcpu (SCPI DVFS clock 0) rate: 1000000000 / cpu_clk rate: 708000000
- vcpu (SCPI DVFS clock 0) rate: 1512000000 / cpu_clk rate: 708000000
Unfortunately the CLKID_CPUCLK was already exported (but is currently
not used) to DT. Due to the removal of this clock definition there is
now a hole in the clk_hw_onecell_data (which is not a problem because
this case is already handled in gxbb_clkc_probe).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The CPU clock defined in the Meson GX clock driver is actually a
left-over from the Meson8b clock controller. Un-export the clock so we
can remove it from the driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Expose the clock ids of the three none AO uarts to the dt-bindings
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[tidy the commit message to match similar change]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Expose the SPICC gate clock to enable the SPICC controller.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[tidy commit message to match similar changes]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Expose the spdif master clock and the mux to select the appropriate spdif
clock parent depending on the data source.
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Expose the clock gates required for the spdif output
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
AHB BIST gate is actually controlled with bit 7.
This bug was detected while trying to use the NAND controller which is
using the DMA engine to transfer data to the NAND.
Since the ahb_bist_clk gate bit conflicts with the ahb_dma_clk gate bit,
the core was disabling the DMA engine clock as part of its 'disable
unused clks' procedure, which was causing all DMA transfers to fail after
this point.
Fixes: 5e73761786 ("clk: sunxi-ng: Add sun5i CCU driver")
Cc: stable@vger.kernel.org
Reported-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1495643669-28221-1-git-send-email-boris.brezillon@free-electrons.com
Add a new R-Car E2 Clock Pulse Generator / Module Standby and Software
Reset driver, using the CPG/MSSR driver core. This will enable support
for module resets, which are not supported by the existing driver.
The old driver can still be used through a Kconfig option, to preserve
backward compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a new R-Car V2H Clock Pulse Generator / Module Standby and Software
Reset driver, using the CPG/MSSR driver core. This will enable support
for module resets, which are not supported by the existing driver.
The old driver can still be used through a Kconfig option, to preserve
backward compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a new R-Car M2-W/N Clock Pulse Generator / Module Standby and
Software Reset driver, using the CPG/MSSR driver core. This will enable
support for module resets, which are not supported by the existing
driver.
The old driver can still be used through a Kconfig option, to preserve
backward compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a new R-Car H2 Clock Pulse Generator / Module Standby and Software
Reset driver, using the CPG/MSSR driver core. This will enable support
for module resets, which are not supported by the existing driver.
The old driver can still be used through a Kconfig option, to preserve
backward compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The goals are to:
- Allow precise control over and automatic selection of which
(sub)drivers are used for which SoC (which may change in the
future),
- Allow adding support for new SoCs easily,
- Allow compile-testing of all (sub)drivers,
- Keep driver selection logic in the subsystem-specific Kconfig,
independent from the architecture-specific Kconfig (i.e. no "select"
from arch/arm64/Kconfig.platforms), to avoid dependencies.
This is implemented by:
- Introducing Kconfig symbols for all drivers and sub-drivers,
- Introducing the Kconfig symbol CLK_RENESAS, which is enabled
automatically when building for a Renesas ARM platform, and which
enables all required drivers without interaction of the user, based
on SoC-specific ARCH_* symbols,
- Allowing the user to enable any Kconfig symbol manually if
COMPILE_TEST is enabled,
- Using the new Kconfig symbols instead of the ARCH_* symbols to
control compilation in the Makefile,
- Always entering drivers/clk/renesas/ during the build.
Note that currently not all (sub)drivers are enabled for
compile-testing, as they depend on independent fixes in other
subsystems.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Coccinelle warns:
drivers/clk/renesas/renesas-cpg-mssr.c:323:14-21: ERROR: PTR_ERR applied after initialization to constant on line 260
Initialize clk using ERR_PTR(-ENOTSUPP) instead of NULL to fix this.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The newly added PRCM CCU driver uses SUNXI_CCU_MP_WITH_MUX_GATE, which causes
a link error when no other driver enables SUNXI_CCU_MP:
drivers/clk/built-in.o:(.data+0x5c8c8): undefined reference to `ccu_mp_ops'
This adds an explicit 'select' statement for it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
support more cpu freq, and add armcore div setting.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With CONFIG_RESET_CONTROLLER=n we see the following link error in the
meson gxbb clk driver:
drivers/built-in.o: In function 'gxbb_aoclkc_probe':
drivers/clk/meson/gxbb-aoclk.c:161: undefined reference to 'devm_reset_controller_register'
Fix this by selecting the reset controller subsystem.
Fixes: f8c11f7991 ("clk: meson: Add GXBB AO Clock and Reset controller driver")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: Added fixes-by tag]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Cfr. the errata of April 14, 2017, for the R-Car Gen3 Hardware Manual
Rev. 0.53E.
These have no user-visible effect, as the clock frequencies stay the
same.
Fixes: 5573d19412 ("clk: renesas: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The pm_subsys_data.clock_list member exists only if CONFIG_PM_CLK=y.
Hence direct accesses to this field break compile-testing on platforms
where CONFIG_PM_CLK=n.
To fix this, use the pm_clk_no_clocks() helper instead, for which a
dummy version is provided if CONFIG_PM_CLK=n.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
R-Car V2H does not have "DIV6" programmable clocks, hence there is no
need to build clk-div6.o.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add the "intc-ex" clock to the R8A7796 CPG MSSR driver.
According to information from the hardware team the INTC-EX
parent clock is CP. The next data sheet version will include
this information.
[takeshi.kihara.df: Ported from commit f099aa0757 ("clk: shmobile:
r8a7795: Add INTC-EX clock") to drivers/clk/renesas/r8a7796-cpg-mssr.c]
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to tables 7.5b and 7.6b of the RZ/G Series Hardware User's
Manual Rev.1.00, MD19=0 is a prohibited setting.
Hence stop looking at MD19, and remove all PLL configurations for
MD19=0.
Fixes: 9127d54bb8 ("clk: renesas: cpg-mssr: Add R8A7745 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RZ/G1E does not have the SCU-SRC[0789] modules and module clocks.
Fixes: 9127d54bb8 ("clk: renesas: cpg-mssr: Add R8A7745 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car V2H and E2 do not have the PLL0CR register, but use a fixed
multiplier (depending on mode pins) and divider.
This corrects the clock rate of "pll0" (PLL0 VCO after post divider) on
R-Car V2H and E2 from 1.5 GHz to 1 GHz.
Inspired by Sergei Shtylyov's work for the common R-Car Gen2 and RZ/G
Clock Pulse Generator support core.
Fixes: 7c4163aae3 ("ARM: dts: r8a7792: initial SoC device tree")
Fixes: 0dce5454d5 ("ARM: shmobile: Initial r8a7794 SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
V3S's usb otg device reset bit should be 24, not 23.
Cc: stable@vger.kernel.org
Signed-off-by: Yong Deng <iemdey@gmail.com>
Reviewed-By: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The register offset for the lcd1-ch1 clock was incorrectly pointing to
the lcd0-ch1 clock. This resulted in the lcd0-ch1 clock being disabled
when the clk core disables unused clocks. This then stops the simplefb
HDMI output path.
Reported-by: Bob Ham <rah@settrans.net>
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Cc: stable@vger.kernel.org # 4.9.x-
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
to me not catching up as quickly on patch review than anything else.
Overall it seems normal though, a few small changes to the core, mostly
small non-critical fixes here and there as well as driver updates for new
and existing hardware support. The biggest things are the TI clk driver
rework to lay the groundwork for clkctrl support in the next merge window
and the AmLogic audio/graphics clk support.
Core:
* clk_possible_parents debugfs file so we know which parents a clk
could possibly have
* Fix to make clk rate change notifiers stop on the first failure instead
of continuing
New Drivers:
* Mediatek MT6797 SoCs
* hi655x PMIC clks
* AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
* Allwinner H5 SoCs and PRCM hardware
Updates:
* Nvidia Tegra T210 cleanups and non-critical fixes
* TI OMAP cleanups in preparation for clkctrl support
* Trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
* ZTE zx296718 SoC VGA clks
* Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
* Support for IDT VersaClock 5P49V5935
* Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=/5a/
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Sort of on the quieter side this time, which is probably due more to
me not catching up as quickly on patch review than anything else.
Overall it seems normal though, a few small changes to the core,
mostly small non-critical fixes here and there as well as driver
updates for new and existing hardware support.
The biggest things are the TI clk driver rework to lay the groundwork
for clkctrl support in the next merge window and the AmLogic
audio/graphics clk support.
Core:
- clk_possible_parents debugfs file so we know which parents a clk
could possibly have
- Fix to make clk rate change notifiers stop on the first failure
instead of continuing
New Drivers:
- Mediatek MT6797 SoCs
- hi655x PMIC clks
- AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
- Allwinner H5 SoCs and PRCM hardware
Updates:
- Nvidia Tegra T210 cleanups and non-critical fixes
- TI OMAP cleanups in preparation for clkctrl support
- trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
- ZTE zx296718 SoC VGA clks
- Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
- IDT VersaClock 5P49V5935 support
- Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3
support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (151 commits)
clk: x86: pmc-atom: Checking for IS_ERR() instead of NULL
clk: ti: divider: try to fix ti_clk_register_divider
clk: mvebu: Use kcalloc() in two functions
clk: mvebu: Use kcalloc() in of_cpu_clk_setup()
clk: nomadik: Delete error messages for a failed memory allocation in two functions
clk: nomadik: Use seq_puts() in nomadik_src_clk_show()
clk: Improve a size determination in two functions
clk: Replace four seq_printf() calls by seq_putc()
clk: si5351: Delete an error message for a failed memory allocation in si5351_i2c_probe()
clk: si5351: Use devm_kcalloc() in si5351_i2c_probe()
clk: at91: Use kcalloc() in of_at91_clk_pll_get_characteristics()
reset: mediatek: Add MT2701 ethsys reset controller include file
clk: mediatek: add mt2701 ethernet reset
clk: hi6220: Add the hi655x's pmic clock
clk: ti: fix building without legacy omap3
clk: ti: fix linker error with !SOC_OMAP4
clk: hi3620: Fix a typo in one variable name
clk: hi3620: Delete error messages for a failed memory allocation in two functions
clk: hi3620: Use kcalloc() in hi3620_mmc_clk_init()
clk: hisilicon: Delete error messages for failed memory allocations in hisi_clk_init()
...
Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch of smaller
changes, but also some new platforms that are worth mentioning:
* Rockchip RK3399 platforms for Chromebooks, including Samsung Chromebook
Plus (Kevin)
* Orange Pi PC2 (Allwinner H5)
* Freescale LS2088A and LS1088A SoCs
* Expanded support for Nvidia Tegra186 (and Jetson TX2)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=q3Ix
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch
of smaller changes, but also some new platforms that are worth
mentioning:
- Rockchip RK3399 platforms for Chromebooks, including Samsung
Chromebook Plus (Kevin)
- Orange Pi PC2 (Allwinner H5)
- Freescale LS2088A and LS1088A SoCs
- Expanded support for Nvidia Tegra186 (and Jetson TX2)"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (180 commits)
arm64: dts: Add basic DT to support Spreadtrum's SP9860G
arm64: dts: exynos: Use - instead of @ for DT OPP entries
arm64: dts: exynos: Add support for s6e3hf2 panel device on TM2e board
arm64: dts: juno: add information about L1 and L2 caches
arm64: dts: juno: fix few unit address format warnings
arm64: marvell: dts: enable the crypto engine on the Armada 8040 DB
arm64: marvell: dts: enable the crypto engine on the Armada 7040 DB
arm64: marvell: dts: add crypto engine description for 7k/8k
arm64: dts: marvell: add sdhci support for Armada 7K/8K
arm64: dts: marvell: add eMMC support for Armada 37xx
arm64: dts: hisi: add pinctrl dtsi file for HiKey960 development board
arm64: dts: hisi: add drive strength levels of the pins for Hi3660 SoC
arm64: dts: hisi: enable the NIC and SAS for the hip07-d05 board
arm64: dts: hisi: add SAS nodes for the hip07 SoC
arm64: dts: hisi: add RoCE nodes for the hip07 SoC
arm64: dts: hisi: add network related nodes for the hip07 SoC
arm64: dts: hisi: add mbigen nodes for the hip07 SoC
arm64: dts: rockchip: fix the memory size of PX5 Evaluation board
arm64: dts: hisilicon: add dts files for hi3798cv200-poplar board
dt-bindings: arm: hisilicon: add bindings for hi3798cv200 SoC and Poplar board
...
Driver updates for ARM SoCs.
* Reset subsystem, merged through arm-soc by tradition:
- Make bool drivers explicitly non-modular
- New support for i.MX7 and Arria10 reset controllers
* PATA driver for Palmchip BK371 (acked by Tejun)
* Power domain drivers for i.MX (GPC, GPCv2)
- Moved out of mach-imx for GPC
- Bunch of tweaks, fixes, etc
* PMC support for Tegra186
* SoC detection support for Renesas RZ/G1H and RZ/G1N
* Move Tegra flow controller driver from mach directory to drivers/soc
- (Power management / CPU power driver)
* Misc smaller tweaks for other platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=B43K
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs:
Reset subsystem, merged through arm-soc by tradition:
- Make bool drivers explicitly non-modular
- New support for i.MX7 and Arria10 reset controllers
PATA driver for Palmchip BK371 (acked by Tejun)
Power domain drivers for i.MX (GPC, GPCv2)
- Moved out of mach-imx for GPC
- Bunch of tweaks, fixes, etc
PMC support for Tegra186
SoC detection support for Renesas RZ/G1H and RZ/G1N
Move Tegra flow controller driver from mach directory to drivers/soc
- (Power management / CPU power driver)
Misc smaller tweaks for other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
soc: pm-domain: Fix the mangled urls
soc: renesas: rcar-sysc: Add support for R-Car H3 ES2.0
soc: renesas: rcar-sysc: Add support for fixing up power area tables
soc: renesas: Register SoC device early
soc: imx: gpc: add workaround for i.MX6QP to the GPC PD driver
dt-bindings: imx-gpc: add i.MX6 QuadPlus compatible
soc: imx: gpc: add defines for domain index
soc: imx: Add GPCv2 power gating driver
dt-bindings: Add GPCv2 power gating driver
ARM/clk: move the ICST library to drivers/clk
ARM: plat-versatile: remove stale clock header
ARM: keystone: Drop PM domain support for k2g
soc: ti: Add ti_sci_pm_domains driver
dt-bindings: Add TI SCI PM Domains
PM / Domains: Do not check if simple providers have phandle cells
PM / Domains: Add generic data pointer to genpd data struct
soc/tegra: Add initial flowctrl support for Tegra132/210
soc/tegra: flowctrl: Add basic platform driver
soc/tegra: Move Tegra flowctrl driver
ARM: tegra: Remove unnecessary inclusion of flowctrl header
...
This typo is quite common. Fix it and add it to the spelling file so
that checkpatch catches it earlier.
Link: http://lkml.kernel.org/r/20170317011131.6881-2-sboyd@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Continue to re-factor code to prepare for eMMC CMDQ and blkmq support
- Introduce queue semantics to prepare for eMMC CMDQ and blkmq support
- Add helper functions to manage temporary enable/disable of eMMC CMDQ
- Improve wait-busy detection for SDIO
MMC host:
- cavium: Add driver to support Cavium controllers
- cavium: Extend Cavium driver to support Octeon SOCs and ThunderX SOCs
- bcm2835: Add new driver for Broadcom BCM2835 controller
- sdhci-xenon: Add driver to support Marvell Xenon SDHCI controller
- sdhci-tegra: Add support for the Tegra186 variant
- sdhci-of-esdhc: Support for UHS-I SD cards
- sdhci-of-esdhc: Support for eMMC HS200 cards
- sdhci-cadence: Add eMMC HS400 enhanced strobe support
- sdhci-esdhc-imx: Reset tuning circuit when needed
- sdhci-pci: Modernize and clean-up some PM related code
- sdhci-pci: Avoid re-tuning at runtime PM for some Intel devices
- sdhci-pci|acpi: Use aggressive PM for some Intel BYT controllers
- sdhci: Re-factoring and modernizations
- sdhci: Optimize delay loops
- sdhci: Improve register dump print format
- sdhci: Add support for the Command Queue Engine
- meson-gx: Various improvements and clean-ups
- meson-gx: Add support for CMD23
- meson-gx: Basic tuning support to avoid CRC errors
- s3cmci: Enable probing via DT
- mediatek: Improve tuning support for eMMC HS200 and HS400 mode
- tmio: Improve DMA support
- tmio: Use correct response for CMD12
- dw_mmc: Minor improvements and clean-ups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=p+Hb
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Continue to re-factor code to prepare for eMMC CMDQ and blkmq support
- Introduce queue semantics to prepare for eMMC CMDQ and blkmq support
- Add helper functions to manage temporary enable/disable of eMMC CMDQ
- Improve wait-busy detection for SDIO
MMC host:
- cavium: Add driver to support Cavium controllers
- cavium: Extend Cavium driver to support Octeon and ThunderX SOCs
- bcm2835: Add new driver for Broadcom BCM2835 controller
- sdhci-xenon: Add driver to support Marvell Xenon SDHCI controller
- sdhci-tegra: Add support for the Tegra186 variant
- sdhci-of-esdhc: Support for UHS-I SD cards
- sdhci-of-esdhc: Support for eMMC HS200 cards
- sdhci-cadence: Add eMMC HS400 enhanced strobe support
- sdhci-esdhc-imx: Reset tuning circuit when needed
- sdhci-pci: Modernize and clean-up some PM related code
- sdhci-pci: Avoid re-tuning at runtime PM for some Intel devices
- sdhci-pci|acpi: Use aggressive PM for some Intel BYT controllers
- sdhci: Re-factoring and modernizations
- sdhci: Optimize delay loops
- sdhci: Improve register dump print format
- sdhci: Add support for the Command Queue Engine
- meson-gx: Various improvements and clean-ups
- meson-gx: Add support for CMD23
- meson-gx: Basic tuning support to avoid CRC errors
- s3cmci: Enable probing via DT
- mediatek: Improve tuning support for eMMC HS200 and HS400 mode
- tmio: Improve DMA support
- tmio: Use correct response for CMD12
- dw_mmc: Minor improvements and clean-ups"
* tag 'mmc-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (148 commits)
mmc: sdhci-of-esdhc: limit SD clock for ls1012a/ls1046a
mmc: sdhci-of-esdhc: poll ESDHC_CLOCK_STABLE bit with udelay
mmc: sdhci-xenon: Fix default value of LOGIC_TIMING_ADJUST for eMMC5.0 PHY
mmc: sdhci-xenon: Fix the work flow in xenon_remove().
MIPS: Octeon: cavium_octeon_defconfig: Enable Octeon MMC
mmc: sdhci-xenon: Remove redundant dev_err call in get_dt_pad_ctrl_data()
mmc: cavium: Use module_pci_driver to simplify the code
mmc: cavium: Add MMC support for Octeon SOCs.
mmc: cavium: Fix detection of block or byte addressing.
mmc: core: Export API to allow hosts to get the card address
mmc: sdio: Fix sdio wait busy implement limitation
mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card
clk: apn806: fix spelling mistake: "mising" -> "missing"
mmc: sdhci-of-esdhc: add delay between tuning cycles
mmc: sdhci: Control the delay between tuning commands
mmc: sdhci-of-esdhc: add tuning support
mmc: sdhci-of-esdhc: add support for signal voltage switch
mmc: sdhci-of-esdhc: add peripheral clock support
mmc: sdhci-pci: Allow for 3 bytes from Intel DSM
mmc: cavium: Fix a shift wrapping bug
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.12:
API:
- Add batch registration for acomp/scomp
- Change acomp testing to non-unique compressed result
- Extend algorithm name limit to 128 bytes
- Require setkey before accept(2) in algif_aead
Algorithms:
- Add support for deflate rfc1950 (zlib)
Drivers:
- Add accelerated crct10dif for powerpc
- Add crc32 in stm32
- Add sha384/sha512 in ccp
- Add 3des/gcm(aes) for v5 devices in ccp
- Add Queue Interface (QI) backend support in caam
- Add new Exynos RNG driver
- Add ThunderX ZIP driver
- Add driver for hardware random generator on MT7623 SoC"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (101 commits)
crypto: stm32 - Fix OF module alias information
crypto: algif_aead - Require setkey before accept(2)
crypto: scomp - add support for deflate rfc1950 (zlib)
crypto: scomp - allow registration of multiple scomps
crypto: ccp - Change ISR handler method for a v5 CCP
crypto: ccp - Change ISR handler method for a v3 CCP
crypto: crypto4xx - rename ce_ring_contol to ce_ring_control
crypto: testmgr - Allow ecb(cipher_null) in FIPS mode
Revert "crypto: arm64/sha - Add constant operand modifier to ASM_EXPORT"
crypto: ccp - Disable interrupts early on unload
crypto: ccp - Use only the relevant interrupt bits
hwrng: mtk - Add driver for hardware random generator on MT7623 SoC
dt-bindings: hwrng: Add Mediatek hardware random generator bindings
crypto: crct10dif-vpmsum - Fix missing preempt_disable()
crypto: testmgr - replace compression known answer test
crypto: acomp - allow registration of multiple acomps
hwrng: n2 - Use devm_kcalloc() in n2rng_probe()
crypto: chcr - Fix error handling related to 'chcr_alloc_shash'
padata: get_next is never NULL
crypto: exynos - Add new Exynos RNG driver
...
Commit 6c0afb5039 ("clk: ti: convert to use proper register
definition for all accesses") converted all register accesses in
the TI clk driver to use a proper struct instead of a void
pointer casted struct that fits into a u32. Unfortunately, it
missed a conversion here in the didivder code, leading to a
compiler warning like so:
drivers/clk/ti/divider.c: In function 'ti_clk_register_divider':
drivers/clk/ti/divider.c:460:8: error: 'reg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Treating a 'u32' variable as a structure leads to a stack
overflow here, and the register address we pass down is never
initialized. Convert this part of the code as well so things
work properly.
Fixes: 6c0afb5039 ("clk: ti: convert to use proper register definition for all accesses")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[sboyd@codeaurora.org: Fixed fixes tag, rewrote commit message,
s/reg_setup/reg/]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When the base driver is enabled but all SoC specific drivers are turned
off, we now get a build error after code was added to always refer to the
clk gates:
drivers/clk/built-in.o: In function `ccu_pll_notifier_cb':
:(.text+0x154f8): undefined reference to `ccu_gate_helper_disable'
:(.text+0x15504): undefined reference to `ccu_gate_helper_enable'
This changes the Kconfig to always require the gate code to be built-in
when CONFIG_SUNXI_CCU is set.
Fixes: 02ae2bc6fe ("clk: sunxi-ng: Add clk notifier to gate then ungate PLL clocks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
trivial fix to spelling mistake in dev_warn message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
First version of the binding didn't have the eMMC clock. This patch
allows to not registering the eMMC clock if it is not present in the
device tree. Then the device tree can be backwards compatible.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add fixed clock of 400MHz to system controller driver. This clock is
used as SD/eMMC clock source.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Omri Itach <omrii@marvell.com>
Reviewed-by: Hanna Hawa <hannah@marvell.com>
[fixed up conflicts, added error handling --rmk]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* Multiplications for the size determination of memory allocations
indicated that array data structures should be processed.
Thus use the corresponding function "kcalloc".
This issue was detected by using the Coccinelle software.
* Replace the specification of data types by pointer dereferences
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Multiplications for the size determination of memory allocations
indicated that array data structures should be processed.
Thus use the corresponding function "kcalloc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
A string which did not contain a data format specification should be put
into a sequence. Thus use the corresponding function "seq_puts".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Replace the specification of two data structures by pointer dereferences
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Four single characters should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The script "checkpatch.pl" pointed information out like the following.
* CHECK: Comparison to NULL could be written "!drvdata"
Thus adjust this expression.
* WARNING: Possible unnecessary 'out of memory' message
Thus remove such a statement here.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Multiplications for the size determination of memory allocations
indicated that array data structures should be processed.
Thus use the corresponding function "devm_kcalloc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Multiplications for the size determination of memory allocations
indicated that array data structures should be processed.
Thus use the corresponding function "kcalloc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The ethernet clock core has a reset register that is currently not exposed
to the user. Fix this by adding the missing registration code.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
A few minor bug and comment fixes, plus some fixes for the PRCM CCU driver
merged in the prior pull request
-----BEGIN PGP SIGNATURE-----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=Gi2w
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-4.12-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into HEAD
Pull Allwinner clock changes, take 2 from Maxime Ripard:
A few minor bug and comment fixes, plus some fixes for the PRCM CCU driver
merged in the prior pull request
* tag 'sunxi-clk-for-4.12-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: a80: Fix audio PLL comment not matching actual code
clk: sunxi-ng: Fix round_rate/set_rate multiplier minimum mismatch
clk: sunxi-ng: use 1 as fallback for minimum multiplier
clk: sunxi-ng: fix PRCM CCU CLK_NUMBER value
clk: sunxi-ng: fix PRCM CCU ir clk parent
The hi655x multi function device is a PMIC providing regulators.
The PMIC also provides a clock for the WiFi and the Bluetooth, let's implement
this clock in order to add it in the hi655x MFD and allow proper wireless
initialization.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[sboyd@codeaurora.org: Remove clkdev usage]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When CONFIG_ATAGS or CONFIG_OMAP3 is disabled, we get a build error:
In file included from include/linux/clk-provider.h:15:0,
from drivers/clk/ti/clk.c:19:
drivers/clk/ti/clk.c: In function 'ti_clk_add_aliases':
drivers/clk/ti/clk.c:438:29: error: 'simple_clk_match_table' undeclared (first use in this function); did you mean 'simple_attr_write'?
Moving the match table down fixes it.
Fixes: c17435c56b ("clk: ti: add API for creating aliases automatically for simple clock types")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When none of the OMAP4-generation SoCs are enabled, we run into a link
error for am43xx/am43xx:
drivers/clk/ti/dpll.o: In function `of_ti_am3_dpll_x2_setup':
dpll.c:(.init.text+0xd8): undefined reference to `clkhwops_omap4_dpllmx'
This is easily fixed by adding another #ifdef.
While looking at the code, I also spotted another problem with the
assignment of hw_ops variable that is not used again later. I'm
changing this to setting clk_hw->ops instead, which I guess is what
was intended here.
Fixes: 473adbf4e0 ("clk: ti: dpll44xx: fix clksel register initialization")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tero Kristo <t-kristo@ti.com>
[sboyd@codeaurora.org: Replaced fixes tag with correct one]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The script "checkpatch.pl" pointed information out like the following.
CHECK: 'seperated' may be misspelled - perhaps 'separated'?
Thus rename the affected variable.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The script "checkpatch.pl" pointed information out like the following.
WARNING: Possible unnecessary 'out of memory' message
Thus remove such statements here.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kcalloc".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The script "checkpatch.pl" pointed information out like the following.
WARNING: Possible unnecessary 'out of memory' message
Thus remove such statements here.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "devm_kmalloc_array".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kcalloc".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
cs2000 can select Static/Dynamic ratio based Frequency Synthesizer
Mode, it can select 20.12 High Multiplier interpret for 32-bit
User Defined Ratio if Dynamic ratio mode. Otherwise it should select
12.20 High Accuracy mode.
Current cs2000 is supporting Static ratio mode only, so it should
select 12.20 High Accuracy mode, not 20.12 High Multiplier mode.
This patch fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
DEVICE_CFG2 can select ratio from user defined ratio and LOCKCLK is
for it. But current driver sets fixed 0 value. This patch fixes it.
Note is that current cs2000 driver is using/supporting only ratio0
(= ch0) now.
DEVICE_CFG2 can select STATIC/DYNAMIC ratio mode, and current cs2000
driver is selecting STATIC mode, but it was not understandable on
current code. This patch also solve this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
CLK_IN skipping mode allows the PLL to maintain lock even when the
CLK_IN signal has missing pulses for up to 20 ms (t CS) at a time.
This patch enables it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Make venus_gdsc parent of venus gdsc core0 and core1.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Due to timing requirements, TI and Conexant manage the audio
reference clock from their ASoC codec drivers using the "mclk"
string. This patch adds another lookup for the "pmc_plt_clk_3"
clock to avoid Intel-specific tests in those codec drivers and
use code as-is.
To avoid a leak, clk_add_alias() is not used in this patch.
Instead the lookup is created manually as part of the .probe()
step and dropped in the .remove() step.
"pmc_plt_clk_3" is used exclusively for audio on all known
Baytrail/CherryTrail designs and is e.g. routed on the MCLK
(pin 26) of the MinnowBoardMAX Turbot LSE connector.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Corrected the bits for power and iso.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: f7225a83 ("clk: ns2: add clock support for Broadcom Northstar 2 SoC")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
rpm branch clk rate should requested as either 0 or 1 but not INT_MAX.
This patch fixes rate request for branch clocks during clk handoff.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The USDHC NAND root clock is not gated by any CCM clock gate. Remove
the bogus gate definition.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There is no SPEAr600 device named "adc". Instead, the description of the
ADC was recently added to the Device Tree, and the device name is
"d820b000.adc", so we should associate the ADC gatable clock to this
device name.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the missing ipg_root_clk which actually is already used by many
orphan clks in current tree.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
MX7D ahb clk actually has no LPCG gate, current LPCG offset 0x4200
used actually is for adc, not ahb. After fix, correct ocram_s_clk
parent accordingly as well.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Update IDT VersaClock 5 driver to support 5P49V5935. This chip has
two clock inputs (internal XTAL or external CLKIN), four fractional
dividers (FODs) and five clock outputs (four universal clock outputs
and one reference clock output at OUT0_SELB_I2C).
Current driver supports up to 2 FODs and up to 3 clock outputs. This
patch sets max number of supported FODs to 4 and max number of supported
clock outputs to 5.
Signed-off-by: Alexey Firago <alexey_firago@mentor.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Introduce vc5_chip_info structure to describe features of a particular
VC5 chip (id, number of FODs, number of outputs, flags).
For now flags are only used to indicate if chip has internal XTAL.
vc5_chip_info is set on probe from the matched of_device_id->data.
Also add defines to specify maximum number of FODs and clock outputs
supported by the driver.
With these changes it should be easier to extend driver to support
more VC5 models.
Signed-off-by: Alexey Firago <alexey_firago@mentor.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Support for the new H5 SoC and the PRCM block found in a number of SoCs as
well, plus the usual chunk of fixes and minor enhancements.
-----BEGIN PGP SIGNATURE-----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=V49g
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-next
Pull Allwinner clock patches for 4.12 from Maxime Ripard:
Support for the new H5 SoC and the PRCM block found in a number of SoCs as
well, plus the usual chunk of fixes and minor enhancements.
* tag 'sunxi-clk-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: Display index when clock registration fails
clk: sunxi-ng: a33: Add offset and minimum value for DDR1 PLL N factor
clk: sunxi-ng: a80: Remodel CPU cluster PLLs as N-type multiplier clocks
clk: sunxi-ng: mult: Support PLL lock detection
clk: sunxi-ng: add support for PRCM CCUs
dt-bindings: update device tree binding for Allwinner PRCM CCUs
clk: sunxi-ng: sun5i: Fix mux width for csi clock
clk: sunxi-ng: tighten SoC deps on explicit AllWinner SoCs
clk: sunxi-ng: add Allwinner H5 CCU support for H3 CCU driver
clk: sunxi-ng: gate: Support common pre-dividers
Two build errors fixes for the sunxi-ng drivers.
The two other patches fix random CPU crashes happening on the A33 since
CPUFreq has been enabled in 4.11.
-----BEGIN PGP SIGNATURE-----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=92GZ
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-fixes-for-4.11-2-bis' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Pull Allwinner clock fixes for 4.11 from Maxime Ripard:
Two build errors fixes for the sunxi-ng drivers.
The two other patches fix random CPU crashes happening on the A33 since
CPUFreq has been enabled in 4.11.
* tag 'sunxi-clk-fixes-for-4.11-2-bis' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: a33: gate then ungate PLL CPU clk after rate change
clk: sunxi-ng: Add clk notifier to gate then ungate PLL clocks
clk: sunxi-ng: fix build failure in ccu-sun9i-a80 driver
clk: sunxi-ng: fix build error without CONFIG_RESET_CONTROLLER
We ignore the d1 and d2 dividers in the audio PLL, and force them to
1 (register value 0) at probe time. However the comment preceding the
audio PLL definition says we enforce the default value, which is not
the same.
Fix the preceding comment to match what we do in code.
Fixes: b8eb71dcdd ("clk: sunxi-ng: Add A80 CCU")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In commit 2beaa601c8 ("clk: sunxi-ng: Implement minimum for
multipliers"), the multiplier minimums in the set_rate callback
for NM and NKMP style clocks were not updated.
This patch fixes them to match their round_rate callbacks.
Fixes: 2beaa601c8 ("clk: sunxi-ng: Implement minimum for multipliers")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A zero multiplier does not make sense for clocks.
Use 1 as the minimum when a multiplier minimum isn't specified.
Fixes: 2beaa601c8 ("clk: sunxi-ng: Implement minimum for multipliers")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch utilizes the new PLL clk notifier to gate then ungate the
PLL CPU clock after rate changes. This should mitigate the system
hangs observed after the introduction of cpufreq for the A33.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In common PLL designs, changes to the dividers take effect almost
immediately, while changes to the multipliers (implemented as
dividers in the feedback loop) take a few cycles to work into
the feedback loop for the PLL to stablize.
Sometimes when the PLL clock rate is changed, the decrease in the
divider is too much for the decrease in the multiplier to catch up.
The PLL clock rate will spike, and in some cases, might lock up
completely. This is especially the case if the divider changed is
the pre-divider, which affects the reference frequency.
This patch introduces a clk notifier callback that will gate and
then ungate a clk after a rate change, effectively resetting it,
so it continues to work, despite any possible lockups. Care must
be taken to reparent any consumers to other temporary clocks during
the rate change, and that this notifier callback must be the first
to be registered.
This is intended to fix occasional lockups with cpufreq on newer
Allwinner SoCs, such as the A33 and the H3. Previously it was
thought that reparenting the cpu clock away from the PLL while
it stabilized was enough, as this worked quite well on the A31.
On the A33, hangs have been observed after cpufreq was recently
introduced. With the H3, a more thorough test [1] showed that
reparenting alone isn't enough. The system still locks up unless
the dividers are limited to 1.
A hunch was if the PLL was stuck in some unknown state, perhaps
gating then ungating it would bring it back to normal. Tests
done by Icenowy Zheng using Ondrej's test firmware shows this
to be a valid solution.
[1] http://www.spinics.net/lists/arm-kernel/msg552501.html
Reported-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ccu-sun9i-a80 driver uses the ccu_mult_ops struct, but unlike the other
users it doesen't select the corresponding Kconfig symbol under which the
struct is compiled in.
This results in the following link error with CONFIG_SUN9I_A80_CCU=y and
CONFIG_SUNXI_CCU_MULT=n:
drivers/built-in.o:(.data+0x2d638): undefined reference to 'ccu_mult_ops'
Fix this by explicitly selecting CONFIG_SUNXI_CCU_MULT like the other
users of the struct.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With CONFIG_RESET_CONTROLLER=n we get the following link error in the
sunxi-ng clk driver:
drivers/built-in.o: In function `sunxi_ccu_probe':
mux-core.c:(.text+0x12fe68): undefined reference to 'reset_controller_register'
mux-core.c:(.text+0x12fe68): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'reset_controller_register'
Fix this by adding the appropriate select statement.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* Protect against holes in onecell_data
* Fix divison by zero and overflow in the mpll driver
* Add audio clock divider driver for i2s clocks
* Add i2s and spdif master clocks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=RvtY
-----END PGP SIGNATURE-----
Merge tag 'meson-clk-for-4.12' of git://github.com/BayLibre/clk-meson into clk-next
Pull AmLogic clk driver updates from Jerome Brunet:
2nd Amlogic clock driver update for 4.12:
* Protect against holes in onecell_data
* Fix divison by zero and overflow in the mpll driver
* Add audio clock divider driver for i2s clocks
* Add i2s and spdif master clocks
- meson8: add some new PLLs
- new clocks for Mali
- misc fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Tz8Z
-----END PGP SIGNATURE-----
Merge tag 'amlogic-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into clk-next
Same great taste as the previous pull request, but now with 50% less DT
bikeshedding!
Amlogic clock driver updates for v4.12
- meson8: add some new PLLs
- new clocks for Mali
- misc fixes.
In case there are multiple notify chains for the same clocks (because they
were registered by different users), we need to propagate potential failure
of any single one of them to the caller. Otherwise we eg risk violating the
V/f curve when a notifier is used for DVFS.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
For validation purposes, it's often useful to be able to retrieve the list
of possible parents in userspace. Add a debugfs file for every clock which
has more than 1 possible parent.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Mayo <jmayo@nvidia.com>
[sboyd@codeaurora.org: Remove useless cast from void and extra
newline]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
These should be const.
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
It adds zx296718 pll_vga clock for VGA support, so that VGA device can
get required pixel rate from clock driver for different display mode.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The bit 0 of PLL_CFG0 register is not powerdown on zx296718, but part of
of postdiv2 field. The consequence is that functions like hw_to_idx()
and zx_pll_enable() will end up tampering the postdiv2 of the PLL.
Let's fix it by defining pd_bit 0xff which is obviously invalid for a
bit position and having PLL driver check the validity before operating
on the bit.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
To support VOU VGA display driver with different modes, we need to set
flag for a few clocks, so that clk_set_rate() call in VOU driver can get
VGA device desired pixel rate.
While at it, the divider between pll_vga and clk_vga gets corrected, as
it's 1:1 instead of 1:2.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The clock was mapped on CG15 (gpio2_clocks) in the CCRG0 register.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Thus CS2000 datasheet is indicating below, this patch
follows it.
WARNING: All "Reserved" registers must maintain their default
state to ensure proper functional operation.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Fix a typo which caused both vfe0 and vfe1 powerdomains to be
named as vfe0.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Fixes: 7e824d5079 ("clk: qcom: gdsc: Add mmcc gdscs for msm8996 family")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Use a classic polling to test bit ready.
And the shift of the bit ready of LSE & LSI were wrongs.
Fixes: 861adc44d2 ("clk: stm32f4: Add LSI & LSE clocks")
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Remove the redundant check of 'rate' in the if statement of the
'pll_set_rate' function
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Fixes: 5fe225c105 ("clk: iproc: add initial common clock support")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
as well as fixups of the clock-ids on rk3368 timers, which were unused
and completely wrong (more and differently named timers).
Also there is one new clock on rk3328 using the muxgrf type, a fix for
pll enablement which should wait for the pll to lock before continuing,
some more critical clocks and the rename of the rk1108 to rv1108, as the
soc seems to have been using a preliminary name before its actual release.
The plan is to have the driver changes (pinctrl, clk) go through the
respective maintainer trees and once everything landed in mainline do
the rename of the devicetree files. With the dts-include change in the
clock rename, we also keep everything compiling and thus bisectability.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAljY7X0QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgRKaCACXoa3hjtS3CSqyJZQyMPPQ0Oda7bblrubR
CE4GmuoZTnX/mUENFEmY7R+k0Np7b6ijPgdiFNpeZo0bpXAdi6bNjerG/QdRPV/P
yP9usSk/8Tx/kY7vnSNTve5QiIJDUoWKGY8fn7ped+GmM7Qeb3/QbWR4N/fL4vVD
nSZnKDO7yGMxLqWL0/QzZyiLzXl1ViEkPWFTedMf3cm0A48p8M/K5jinfMvl9I+o
6e2TIsc2zn6vRKuoGhjqcaRxhtRRV9c2O8wVAcA6BLo/kk3pA9ZTU3QJPsqEcN6A
BTbANYfXiQF6i+Xp1YJHcE2lNQ/sWZOTQtLqY9SL5WzMETMTETT5
=In5R
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull rockchip clk driver updates from Heiko Stuebner:
General rockchip clock changes for 4.12. Contains some new clock-ids
as well as fixups of the clock-ids on rk3368 timers, which were unused
and completely wrong (more and differently named timers).
Also there is one new clock on rk3328 using the muxgrf type, a fix for
pll enablement which should wait for the pll to lock before continuing,
some more critical clocks and the rename of the rk1108 to rv1108, as the
soc seems to have been using a preliminary name before its actual release.
The plan is to have the driver changes (pinctrl, clk) go through the
respective maintainer trees and once everything landed in mainline do
the rename of the devicetree files. With the dts-include change in the
clock rename, we also keep everything compiling and thus bisectability.
* tag 'v4.12-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: add pll_wait_lock for pll_enable
clk: rockchip: rename RK1108 to RV1108
dt-bindings: rk1108-cru: rename RK1108 to RV1108
clk: rockchip: mark some rk3368 core-clks as critical
clk: rockchip: export SCLK_TIMERXX id for timers on rk3368
clk: rockchip: describe clk_gmac using the new muxgrf type on rk3328
clk: rockchip: add clock ids for timer10-15 of RK3368 SoCs
clk: rockchip: fix up rk3368 timer-ids
clk: rockchip: add rk3328 clk_mac2io_ext ID
clk: rockchip: Set "ignore unused" for PMU M0 clocks on rk3399
- Add support for the Clock Pulse Generator / Module Standby and
Software Reset module on revision ES2.0 of the R-Car H3 SoC, which
differs from ES1.x in some areas.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rttL
-----END PGP SIGNATURE-----
Merge tag 'clk-renesas-for-v4.12-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next
Pull Renesas clk driver updates from Geert Uytterhoeven:
- Add support for the Clock Pulse Generator / Module Standby and
Software Reset module on revision ES2.0 of the R-Car H3 SoC, which
differs from ES1.x in some areas.
- Add IMR clocks for R-Car H3 and M3-W,
- Add workaround for PLL0/2/4 errata on R-Car H3 ES1.0,
- Small fixes and cleanups.
* tag 'clk-renesas-for-v4.12-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: rcar-gen3-cpg: Add support for RCLK on R-Car H3 ES2.0
clk: renesas: r8a7795: Add support for R-Car H3 ES2.0
clk: renesas: Add r8a7795 ES2.0 CPG Core Clock Definitions
clk: renesas: cpg-mssr: Add support for fixing up clock tables
clk: renesas: rcar-gen3: Add workaround for PLL0/2/4 errata on H3 ES1.0
clk: renesas: rcar-gen3-cpg: Pass mode pins to rcar_gen3_cpg_init()
clk: renesas: r8a7796: Reformat core clock table
clk: renesas: r8a7795: Reformat core clock table
clk: renesas: r8a7796: Correct name of watchdog clock
clk: renesas: r8a7795: Correct name of watchdog clock
clk: renesas: r8a7795: Correct parent clock and sort order for Audio DMACs
clk: renesas: r8a7796: Add IMR clocks
clk: renesas: r8a7795: Add IMR clocks
* 'for-4.12-ti-clk-cleanups' of https://github.com/t-kristo/linux-pm:
clk: ti: convert to use proper register definition for all accesses
clk: ti: dpll44xx: fix clksel register initialization
clk: ti: gate: export gate_clk_ops locally
clk: ti: divider: add driver internal API for parsing divider data
clk: ti: divider: convert TI divider clock to use its own data representation
clk: ti: mux: convert TI mux clock to use its internal data representation
clk: ti: drop unnecessary MEMMAP_ADDRESSING flag
clk: ti: omap4: cleanup unnecessary clock aliases
clk: ti: enforce const types on string arrays
clk: ti: move omap2_init_clk_clkdm under TI clock driver
clk: ti: add clkdm_lookup to the exported functions
clk: ti: use automatic clock alias generation framework
clk: ti: add API for creating aliases automatically for simple clock types
clk: ti: add support for automatic clock alias generation
clk: ti: remove un-used definitions from public clk_hw_omap struct
The debug APB clock is absent in hi6220 driver, so this patch is to add
support for it.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The CLK_NUMBER value of PRCM CCU is wrongly set to (CLK_APB0_PWD + 1),
which prevented the IR mod clock from being set up.
Change it to (CLK_IR + 1) in order to correctly get IR mod set up.
Fixes: cdb8b80b60 ("clk: sunxi-ng: add support for PRCM CCUs")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The first parent of ir clk in PRCM CCU is wrongly written as "osc32K"
instead of "osc32k".
Change it to "osc32k".
Fixes: cdb8b80b60 ("clk: sunxi-ng: add support for PRCM CCUs")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On Meson8b the MPLL parent clock (fixed_pll) has a rate of 2550MHz.
Multiplying this with SDM_DEN results in a value greater than 32bits.
This is not a problem on the 64bit Meson GX SoCs, but it may result in
undefined behavior on the older 32bit Meson8b SoC.
While rate_from_params was only introduced recently to make the math
reusable from _round_rate and _recalc_rate the original bug exists much
longer.
Fixes: 1c50da4f27 ("clk: meson: add mpll support")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[as discussed on the ml, use DIV_ROUND_UP_ULL]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
According to the public datasheet all register bits in HHI_MPLL_CNTL7,
HHI_MPLL_CNTL8 and HHI_MPLL_CNTL9 default to zero. On all GX SoCs these
seem to be initialized by the bootloader to some default value.
However, on my Meson8 board they are not initialized, leading to a
division by zero in rate_from_params as the math is:
(parent_rate * SDM_DEN) / ((SDM_DEN * 0) + 0)
According to the datasheet, the minimum n2 value is 4. The rate provided
by the clock when n2 is less than this minimum is unpredictable. In such
case, we report an error.
Although the rate_from_params function was only introduced recently the
original bug has been there for much longer. It was only exposed
recently when the MPLL clocks were added to the Meson8b clock driver.
Fixes: 1c50da4f27 ("clk: meson: add mpll support")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This adds the cts_i958 clock to control the clock source of the spdif
output block. This mux is not explicitly mentionned in the documentation
but it is critical to the spdif dai. It is used to select whether the clock
source of the spdif output is cts_amclk (when data are taken from i2s
buffer) or the cts_mclk_i958 (when data are taken from the spdif buffer)
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the spdif master clock also referred as cts_mclk_i958
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the i2s master clock also referred as cts_amclk
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The audio divider needs a specific clock divider driver.
With am mpll parent clock, which is able to provide a fairly precise rate,
the generic divider tends to select low value of the divider. In such case
the quality of the clock is very poor. For the same final rate, maximizing
the audio clock divider value and selecting the corresponding mpll rate
gives better results. This is what this driver aims to acheive. So far, so
good.
Cc: Hendrik v. Raven <hendrik@consetetur.de>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The clock controller is getting more complex and it might be possible, in
the future, to have holes in the clk_hw_onecell_data array. Just make sure
we skip those holes if it ever happens.
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This moves the ICST clock divider helper library from
arch/arm/common to drivers/clk/versatile so it is maintained
with the other clock drivers.
We keep the structure as a helper library intact and do not
fuse it with the clk-icst.c Versatile ICST clock driver: there
may be other users out there that need to use this library for
their clocking, and then it will be helpful to keep the
library contained. (The icst.[c|h] files could just be moved
to drivers/clk/lib or a similar location to share the library.)
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add clock index to clock registration failure message. Clock name
is sometimes not available, when things go really wrong.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The DDR1 PLL on the A33 is an oddball amongst the A33 CCU clocks.
It is a clock multiplier, with the effective multiplier in the
range of 12 ~ 255 and no offset between the multiplier value and
the value programmed into the register.
Implement the zero offset and minimum value of 12 for this clock.
Fixes: d05c748bd7 ("clk: sunxi-ng: Add A33 CCU support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CPU cluster PLLs on the A80 are NP clocks that are atypical in two ways:
- The P factor is 1 bit wide, and translates to a /1 or /4 divider.
- The P factor should only be used for output frequencies lower than
288 MHz. The N factor has a lower limit of 12, which likely contributed
to this extra divider.
According to the user manual, the clocks can only go as low as 200 MHz.
The vendor BSP kernel does not even define operating points below 360
MHz for these clocks. The lower end for cpufreq in the vendor kernel is
even higher. The mainline Linux kernel doesn't support cpufreq for the
A80 at the moment. This means the lower frequencies are untested, and
will likely remain unused.
The new sunxi-ng style clocks don't support the quirks listed above.
Instead of trying to work the quirks in for something of little usage,
we re-model the clocks into N-type multipler clocks, with P fixed at 1.
At probe time we check if P is set to 4, and fix it up if needed. This
is highly unlikely though.
Fixes: b8eb71dcdd ("clk: sunxi-ng: Add A80 CCU")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some PLL clocks are N (multiplier) type clocks, or can be simplified
as such. An example of the former is the DDR1 PLL clock on the A33.
An example of the latter is the CPU PLL clock on the A80, in which
the P divider is only used for low frequencies that are of little
use. Both clocks support PLL lock detection.
The mult clock macro implies support for this, but that is not true.
The field is simply discarded. This patch adds proper support for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The clock tree in the Amlogic GXBB and GXL/GXM SoCs is shared, but the GXL/GXM
SoCs embeds a different GP0 PLL, and needs different parameters with a vendor
provided reduced rate table.
This patch adds the GXL GP0 variant, and adds a GXL DT compatible in order
to use the GXL GP0 PLL instead of the GXBB specific one.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490178747-14837-4-git-send-email-narmstrong@baylibre.com
Tha Amlogic GXBB SoC GP0 PLL needs some vendor provided parameters to be
initializated in the the GP0 control registers before configuring the rate
with the rate table provided parameters.
GXBB GP0 PLL tweaks are also selected to respect the vendor init procedure.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490178747-14837-3-git-send-email-narmstrong@baylibre.com
In recent Amlogic GXBB, GXL and GXM SoCs, the GP0 PLL needs some specific
parameters in order to initialize and lock correctly.
This patch adds an optional PARAM table used to initialize the PLL to a
default value with it's parameters in order to achieve to desired frequency.
The GP0 PLL in GXBB, GXL/GXM also needs some tweaks in the initialization
steps, and these are exposed along the PARAM table.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490178747-14837-2-git-send-email-narmstrong@baylibre.com
The Mali is clocked by two identical clock paths behind a glitch free mux
to safely change frequency while running.
The two "mali_0" and "mali_1" clocks are composed of a mux, divider and gate.
Expose these two clocks trees using generic clocks.
Finally the glitch free mux is added as "mali" clock.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490177935-9646-3-git-send-email-narmstrong@baylibre.com
