Instantiate the two Audio DMA controllers in the r8a7791 device tree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[geert: corrected spelling of audmac1]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate the two Audio DMA controllers in the r8a7790 device tree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[geert: corrected spelling of audmac1]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The SATA node used the generic compatible property only, which was
deprecated by commit e67adb4e66 ("sata_rcar: Add R-Car Gen2 SATA
PHY support"). Add the SoC-specific one introduced by that commit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add references to the transmit and receive DMA channels in the MMCIF
node.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add references to the transmit and receive DMA channels in the two
MMCIF nodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Node names should describe the function of the device, not its IP core
name.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The TMU timers used the generic compatible property only.
Add the SoC-specific one, to make it future proof.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The CMT1 timer used the generic compatible property only.
Add the SoC-specific one, which is already documented, to make it future
proof.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable HS-USB device for the Henninger board, defining the GPIO that the driver
should check when probing (which is the ID output from MAX3355 OTG chip).
Note that there will be pinctrl-related error messages if both internal PCI
and HS-USB drivers are enabled but they should be just ignored.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: added pin function/group and prop, moved device node, fixed summary,
added changelog]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable HS-USB device for the Koelsch board, defining the GPIO that the driver
should check when probing (which is the ID output from MAX3355 OTG chip).
Note that there will be pinctrl-related error messages if both internal PCI
and HS-USB drivers are enabled but they should be just ignored.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: added pin function/group and prop, moved device node, fixed summary,
added changelog]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the R8A7791 generic part of the HS-USB device node. It is up to the board
file to enable the device.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: fixed summary, added changelog]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable HS-USB device for the Lager board, defining the GPIO that the driver
should check when probing. Since this board doesn't have the OTG ID pin, we
assume that GP5_18 (USB0_PWEN) is an ID pin because it is 1 when the SW5 is
in position 2-3 (meaning USB function) and 0 in other positions.
Note that there will be pinctrl-related error messages if both internal PCI
and HS-USB drivers are enabled but they should be just ignored.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: added pin node and prop, moved device node, fixed summary, supplemented
changelog]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the R8A7790 generic part of the HS-USB device node.
It is up to the board file to enable the device.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: fixed summary, added changelog]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since the PHY of USB3.0 and EHCI/OHCI ch2 are the same, the USB3.0
driver cannot use the phy driver when the EHCI/OHCI ch2 already used it:
phy phy-e6590100.usb-phy.3: phy init failed --> -16
xhci-hcd: probe of ee000000.usb failed with error -16
If so, we have to unbind the EHCI/OHCI ch2, and then we have to bind
the USB3.0 driver as the following:
echo 0000:02:02.0 > /sys/bus/pci/drivers/ehci-pci/unbind
echo 0000:02:01.0 > /sys/bus/pci/drivers/ohci-pci/unbind
echo ee000000.usb > /sys/bus/platform/drivers/xhci-hcd/bind
Note that there will be pinctrl-related error messages if both
internal PCI and USB3.0 are enabled but they should be just ignored:
sh-pfc e6060000.pfc: pin GP_5_22 already requested by ee0d0000.pci; cannot claim for ee000000.usb
sh-pfc e6060000.pfc: pin-182 (ee000000.usb) status -22
ata1: SATA link down (SStatus 0 SControl 300)
sh-pfc e6060000.pfc: could not request pin 182 (GP_5_22) from group usb2 on device sh-pfc
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Initialise TMU device using DT when booting bockw
using DT-reference.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This describes all of the TMU hardware of the r8a7778.
Each node is disabled and may be enabled as necessary
by board DTS files.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ch0 will be used for clock events and for periodic clock events,
ch1 will be used as clock source.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The clocks property for the scifa2 device node referred to the scifa0
clock index instead of the scifa2 clock index.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SCIF and SCIFA can be plexed onto the same wires on Lager board. The
datasheet also describes the wires as SCIFA. So, to make use of the
bigger FIFOs switch to SCIFA instead.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the PCI USB devices that are behind the PCI bridges, adding necessary
links to the USB PHY device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the PCI USB devices that are behind the PCI bridges, adding necessary
links to the USB PHY device.
Based on the original work by Ben Dooks <ben.dooks@codethink.co.uk>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable USB PHY device for the Henninger board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable USB PHY device for the Koelsch board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the R8A7791 generic part of the USB PHY device node. It is up to the
board file to enable the device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable USB PHY device for the Lager board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the R8A7790 generic part of the USB PHY device node. It is up to the
board file to enable the device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This clock drives the INTCA irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: devicetree@vger.kernel.org
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specify the DU output topology, enable the DU device and configure the
related pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specify the DU output topology, enable the DU device and configure the
related pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specify the DU output topology, enable the DU device and configure the
related pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Mitsubishi AA104XD12 panel is commonly used with the Marzen, Lager
and Koelsch boards. Create a .dtsi file that describe the panel and its
connection to the board.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DU device with a disabled state. Boards that want to enable the
DU need to specify the output topology
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DU device with a disabled state. Boards that want to enable the
DU need to specify the output topology.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[horms+renesas@verge.net.au: resolved minor conflict]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DU device with a disabled state. Boards that want to enable the
DU need to specify the output topology
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[horms+renesas@verge.net.au: resolved minor conflict]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This describes all of the CMT1 hardware of the r8a73a4.
The node is disabled and may be enabled as necessary by board DTS files.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.
Note that we have to keep the "console=ttyS1,115200n81" parameter in
chosen/bootargs, else the console will use the default setting of 9600
baud.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.
In addition, this will allow the PM domain code to find the PM domain
for the console device.
Note that we have to keep the "console=ttySC4" parameter in
chosen/bootargs, else we only get console messages on tty0.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.
Note that we have to keep the "console=ttySC0,38400" parameter in
chosen/bootargs, else the console will use the default setting of 115200
baud.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
