When building for SH7734:
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:1: error: macro "_GP_DATA" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:2: error: '_GP_DATA' undeclared here (not in a function)
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:1: error: macro "_GP_DATA" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:1: error: macro "_GP_DATA" passed 5 arguments, but takes just 4
...
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:1: error: macro "_GP_INOUTSEL" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:53: error: '_GP_INOUTSEL' undeclared here (not in a function)
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:2: warning: initialization makes integer from pointer without a cast [enabled by default]
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:2: warning: (near initialization for '(anonymous)[0]') [enabled by default]
...
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:1: error: macro "_GP_INDT" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:47: error: '_GP_INDT' undeclared here (not in a function)
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:2: warning: initialization makes integer from pointer without a cast [enabled by default]
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:2: warning: (near initialization for '(anonymous)[0]') [enabled by default]
...
Add the missing "cfg" macro parameters to the sh7734-specific
_GP_DATA(), _GP_INOUTSEL(), and _GP_INDT() macros to fix this.
Fixes: 22768fc60a ("pinctrl: sh-pfc: Add macros defining GP ports with config flags")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since Linux gpio framework return 0 for output, 1 for input.
But HW use 0 stands for input, and 1 stands for output.
So use negative to correct it.
And gpio_chip.get is used to get input value, no need to get
output value, so removing it.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When building pinctrl-ssbi-gpio and pinctrl-ssbi-mpp for ARM64, we get
a compile warning about invalid types:
drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c: In function 'pm8xxx_gpio_probe':
drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c:675:17: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/pinctrl/qcom/pinctrl-ssbi-mpp.c: In function 'pm8xxx_mpp_probe':
drivers/pinctrl/qcom/pinctrl-ssbi-mpp.c:766:17: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
This changes the code so we cast the pointer to 'unsigned long', which
is the right thing to do here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
for_each_child_of_node performs an of_node_get on each iteration,
so of_node_put is required on break out of the loop.
This is done using Coccinelle. And semantic patch used for this is
as follows:
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The whole menu is guarded by
menu "Pin controllers"
depends on PINCTRL
...
endmenu
The if conditional outside of it is redundant.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO core:
- Define and handle flags for open drain/open collector
and open source/open emitter, also know as "single-ended"
configurations.
- Generic request/free operations that handle calling out
to the (optional) pin control backend.
- Some refactoring related to an ABI change that did not
happen, yet provide useful.
- Added a real-time compliance checklist. Many GPIO chips
have irqchips, and need to think this over with the RT
patches going upstream.
- Restructure, fix and clean up Kconfig menus a bit.
New drivers:
- New driver for AMD Promony.
- New driver for ACCES 104-IDIO-16, a port-mapped I/O
card, ISA-style. Very retro.
Subdriver changes:
- OMAP changes to handle real time requirements.
- Handle trigger types for edge and level IRQs on PL061
properly. As this hardware is very common it needs to
set a proper example for others to follow.
- Some container_of() cleanups.
- Delete the unused MSM driver in favor of the driver that
is embedded inside the pin control driver.
- Cleanup of the ath79 GPIO driver used by many, many
OpenWRT router targets.
- A consolidated IT87xx driver replacing the earlier
very specific IT8761e driver.
- Handle the TI TCA9539 in the PCA953x driver. Also
handle ACPI devices in this subdriver.
- Drop xilinx arch dependencies as these FPGAs seem to
profilate over a few different architectures. MIPS and
ARM come to mind.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LDCr
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for the v4.4 development cycle.
The only changes hitting outside drivers/gpio are in the pin control
subsystem and these seem to have settled nicely in linux-next.
Development mistakes and catfights are nicely documented in the
reverts as you can see. The outcome of the ABI fight is that we're
working on a chardev ABI for GPIO now, where hope to show results for
the v4.5 kernel.
Summary of changes:
GPIO core:
- Define and handle flags for open drain/open collector and open
source/open emitter, also know as "single-ended" configurations.
- Generic request/free operations that handle calling out to the
(optional) pin control backend.
- Some refactoring related to an ABI change that did not happen, yet
provide useful.
- Added a real-time compliance checklist. Many GPIO chips have
irqchips, and need to think this over with the RT patches going
upstream.
- Restructure, fix and clean up Kconfig menus a bit.
New drivers:
- New driver for AMD Promony.
- New driver for ACCES 104-IDIO-16, a port-mapped I/O card,
ISA-style. Very retro.
Subdriver changes:
- OMAP changes to handle real time requirements.
- Handle trigger types for edge and level IRQs on PL061 properly. As
this hardware is very common it needs to set a proper example for
others to follow.
- Some container_of() cleanups.
- Delete the unused MSM driver in favor of the driver that is
embedded inside the pin control driver.
- Cleanup of the ath79 GPIO driver used by many, many OpenWRT router
targets.
- A consolidated IT87xx driver replacing the earlier very specific
IT8761e driver.
- Handle the TI TCA9539 in the PCA953x driver. Also handle ACPI
devices in this subdriver.
- Drop xilinx arch dependencies as these FPGAs seem to profilate over
a few different architectures. MIPS and ARM come to mind"
* tag 'gpio-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (57 commits)
gpio: fix up SPI submenu
gpio: drop surplus I2C dependencies
gpio: drop surplus X86 dependencies
gpio: dt-bindings: document the official use of "ngpios"
gpio: MAINTAINERS: Add an entry for the ATH79 GPIO driver
gpio / ACPI: Allow shared GPIO event to be read via operation region
gpio: group port-mapped I/O drivers in a menu
gpio: Add ACCES 104-IDIO-16 driver maintainer entry
gpio: zynq: Document interrupt-controller DT binding
gpio: xilinx: Drop architecture dependencies
gpio: generic: Revert to old error handling in bgpio_map
gpio: add a real time compliance notes
Revert "gpio: add a real time compliance checklist"
gpio: Add GPIO support for the ACCES 104-IDIO-16
gpio: driver for AMD Promontory
gpio: xlp: Convert to use gpiolib irqchip helpers
gpio: add a real time compliance checklist
gpio/xilinx: enable for MIPS
gpiolib: Add and use OF_GPIO_SINGLE_ENDED flag
gpiolib: Split GPIO flags parsing and GPIO configuration
...
v4.4 kernel development cycle:
Infrastructure:
- Doug Anderson wrote a patch adding an "init" state
different from the "default" state for pin control
state handling in the core framework. This is applied
before the driver's probe() call if defined and takes
precedence over "default". If both are defined, "init"
will be applied *before* probe() and "default" will be
applied *after* probe().
Significant subdriver improvements:
- SH PFC is switched to getting GPIO ranges from the
device tree ranges property on DT platforms.
- Got rid of CONFIG_ARCH_SHMOBILE_LEGACY, we are all
modernized.
- Got rid of SH PFC hardcoded IRQ numbers.
- Allwinner sunxi external interrupt through the "r"
controller.
- Moved the Cygnus driver to use DT-provided GPIO
ranges.
New drivers:
- Atmel PIO4 pin controller for the SAMA4D2 family
New subdrivers:
- Rockchip RK3036 subdriver
- Renesas SH PFC R8A7795 subdriver
- Allwinner sunxi A83T PIO subdriver
- Freescale i.MX7d iomux lpsr subdriver
- Marvell Berlin BG4CT subdriver
- SiRF Atlas 7 step B SoC subdriver
- Intel Broxton SoC subdriver
Apart from this, the usual slew if syntactic and semantic
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0t3B
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the big bulk of pin control changes for the v4.4 kernel
development cycle. Development pace is high in pin control again this
merge window. 28 contributors, 83 patches.
It hits a few sites outside the pin control subsystem:
- Device tree bindings in Documentation (as usual)
- MAINTAINERS
- drivers/base/* for the "init" state handling by Doug Anderson.
This has been ACKed by Greg.
- drivers/usb/renesas_usbhs/rcar2.c, for a dependent Renesas change
in the USB subsystem. This has been ACKed by both Greg and Felipe.
- arch/arm/boot/dts/sama5d2.dtsi - this should ideally have gone
through the ARM SoC tree but ended up here.
This time I am using Geert Uytterhoeven as submaintainer for SH PFC
since the are three-four people working in parallel with new Renesas
ASICs.
Summary of changes:
Infrastructure:
- Doug Anderson wrote a patch adding an "init" state different from
the "default" state for pin control state handling in the core
framework. This is applied before the driver's probe() call if
defined and takes precedence over "default". If both are defined,
"init" will be applied *before* probe() and "default" will be
applied *after* probe().
Significant subdriver improvements:
- SH PFC is switched to getting GPIO ranges from the device tree
ranges property on DT platforms.
- Got rid of CONFIG_ARCH_SHMOBILE_LEGACY, we are all modernized.
- Got rid of SH PFC hardcoded IRQ numbers.
- Allwinner sunxi external interrupt through the "r" controller.
- Moved the Cygnus driver to use DT-provided GPIO ranges.
New drivers:
- Atmel PIO4 pin controller for the SAMA4D2 family
New subdrivers:
- Rockchip RK3036 subdriver
- Renesas SH PFC R8A7795 subdriver
- Allwinner sunxi A83T PIO subdriver
- Freescale i.MX7d iomux lpsr subdriver
- Marvell Berlin BG4CT subdriver
- SiRF Atlas 7 step B SoC subdriver
- Intel Broxton SoC subdriver
Apart from this, the usual slew if syntactic and semantic fixes"
* tag 'pinctrl-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (81 commits)
pinctrl: pinconf: remove needless loop
pinctrl: uniphier: guard uniphier directory with CONFIG_PINCTRL_UNIPHIER
pinctrl: zynq: fix UTF-8 errors
pinctrl: zynq: Initialize early
pinctrl: at91: add missing of_node_put
pinctrl: tegra-xusb: Correct lane mux options
pinctrl: intel: Add Intel Broxton pin controller support
pinctrl: intel: Allow requesting pins which are in ACPI mode as GPIOs
pinctrl: intel: Add support for multiple GPIO chips sharing the interrupt
drivers/pinctrl: Add the concept of an "init" state
pinctrl: uniphier: set input-enable before pin-muxing
pinctrl: cygnus: Add new compatible string for gpio controller driver
pinctrl: cygnus: Remove GPIO to Pinctrl pin mapping from driver
pinctrl: cygnus: Optional DT property to support pin mappings
pinctrl: sunxi: Add irq pinmuxing to sun6i "r" pincontroller
pinctrl: sunxi: Fix irq_of_xlate for the r_pio pinctrl block
pinctrl: sh-pfc: Remove obsolete r8a7778 platform_device_id entry
pinctrl: sh-pfc: Remove obsolete r8a7779 platform_device_id entry
pinctrl: sh-pfc: Stop including <linux/platform_data/gpio-rcar.h>
usb: renesas_usbhs: Remove unneeded #include <linux/platform_data/gpio-rcar.h>
...
This removes a needless loop which was caught in pinconf.c.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Laurent Meunier <laurent.meunier@st.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CONFIG_PINCTRL_UNIPHIER is more suitable than CONFIG_ARCH_UNIPHIER
to guard the drivers/pinctrl/uniphier directory.
The current CONFIG_PINCTRL_UNIPHIER_CORE is a bit long
(it would break the indentation in drivers/pinctrl/Makefile),
so rename it into CONFIG_PINCTRL_UNIPHIER.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix up Sören's name in the Zynq driver. I caused this. I fix it.
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Supplying pinmux configuration for e.g. gpio pins leads to deferred
probes because the pinctrl device is probed much later than gpio.
Move the init call to a much earlier stage so it probes before the
devices that may need it.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Tested-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The description of the XUSB_PADCTL_USB3_PAD_MUX_0 register in the Tegra124
documentation implies that all functions (pcie, usb3 and sata) can be
muxed onto to all lanes (pcie lanes 0-4 and sata lane 0). However, it has
been confirmed that this is not the case and the mux'ing options much more
limited. Unfortunately, the public documentation has not been updated to
reflect this and so detail the actual mux'ing options here by function:
Function: Lanes:
pcie1 x2: pcie3, pcie4
pcie1 x4: pcie1, pcie2, pcie3, pcie4
pcie2 x1 (option1): pcie0
pcie2 x1 (option2): pcie2
usb3 port 0: pcie0
usb3 port 1 (option 1): pcie1
usb3 port 1 (option 2): sata0
sata: sata0
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver adds pinctrl/GPIO support for Intel Broxton. The GPIO
controller is based on the same hardware design that is already used in
Intel Sunrisepoint so we leverage the core driver here.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reserved for ACPI actually means that in such case the GPIO hardware will
not update the interrupt status register (GPI_IS) even if the pin is
configured to trigger an interrupt. It will update GPI_GPE_STS instead and
does not trigger an interrupt.
Allow using such pins as GPIOs, only prevent their usage as interrupts.
We also rename function intel_pad_reserved_for_acpi() to be
intel_pad_acpi_mode() which reflects the actual meaning better.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Intel Broxton the GPIO hardware consists of several chips that all share
the parent interrupt. It is not possible to handle this by setting chained
handler for each chip (as they will overwrite each other).
To overcome this we need to request the interrupt using devm_request_irq()
and pass IRQF_SHARED with the flags.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For pinctrl the "default" state is applied to pins before the driver's
probe function is called. This is normally a sensible thing to do,
but in some cases can cause problems. That's because the pins will
change state before the driver is given a chance to program how those
pins should behave.
As an example you might have a regulator that is controlled by a PWM
(output high = high voltage, output low = low voltage). The firmware
might leave this pin as driven high. If we allow the driver core to
reconfigure this pin as a PWM pin before the PWM's probe function runs
then you might end up running at too low of a voltage while we probe.
Let's introudce a new "init" state. If this is defined we'll set
pinctrl to this state before probe and then "default" after probe
(unless the driver explicitly changed states already).
An alternative idea that was thought of was to use the pre-existing
"sleep" or "idle" states and add a boolean property that we should
start in that mode. This was not done because the "init" state is
needed for correctness and those other states are only present (and
only transitioned in to and out of) when (optional) power management
is enabled.
Changes in v3:
- Moved declarations to pinctrl/devinfo.h
- Fixed author/SoB
Changes in v2:
- Added comment to pinctrl_init_done() as per Linus W.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While IECTRL is disabled, input signals are pulled-down internally.
If pin-muxing is set up first, glitch signals (Low to High transition)
might be input to hardware blocks.
Bad case scenario:
[1] The hardware block is already running before pinctrl is handled.
(the reset is de-asserted by default or by a firmware, for example)
[2] The pin-muxing is set up. The input signals to hardware block
are pulled-down by the chip-internal biasing.
[3] The pins are input-enabled. The signals from the board reach the
hardware block.
Actually, one invalid character is input to the UART blocks for such
SoCs as PH1-LD4, PH1-sLD8, where UART devices start to run at the
power on reset.
To avoid such problems, pins should be input-enabled before muxing.
Fixes: 6e90889202 ("pinctrl: UniPhier: add UniPhier pinctrl core support")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Dai Okamura <okamura.dai@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove gpio to pinctrl pin mapping code from driver and
address this through standard property "gpio-ranges".
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinmuxing for external interrupt functionality through the
sun6i "r" pincontroller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The r_pio gpio / pin controller has a pin_base of non 0, we need to
adjust for this before calling sunxi_pinctrl_desc_find_function_by_pin.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the removal of the r8a7778 legacy SoC code in commit
4baadb9e05 ("ARM: shmobile: r8a7778: remove obsolete setup code"),
r8a7778 is only supported in generic DT-only ARM multi-platform builds.
The driver doesn't need to match platform devices by name anymore, hence
remove the corresponding platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Since the removal of the r8a7779 legacy SoC code in commit
c99cd90d98 ("ARM: shmobile: r8a7779: Remove legacy SoC code"),
r8a7779 is only supported in generic DT-only ARM multi-platform builds.
The driver doesn't need to match platform devices by name anymore, hence
remove the corresponding platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This header file will be removed soon.
Copy the helper macro RCAR_GP_PIN(), which is used by the pinctrl
drivers only, to sh_pfc.h, and drop the #include.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The sh_pfc_soc_info.gpio_data[] array contains not only GPIO data, but
also various other pinmux-related data (functions and marks).
Every single driver already calls its local array pinmux_data[].
Hence rename the sh_pfc_soc_info member to "pinmux_data".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
On this SoC there is no simple mapping of GP pins to pull-up register
bits, so we need a table.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
PORT_GP_CFG_1 and PORT_GP_CFG_32 work like their non-CFG counterparts
but accept an extra argument with config flags.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add VIN0/1 pin groups to R8A7794 PFC driver.
Sergei: rebased, renamed, added changelog, gathered 12 VIN1 data pins into
a single pin group, added "vin1_data10" pin group, used 'union vin_data' and
VIN_DATA_PIN_GROUP() macro to describe VIN1 pins, reversed the order of the
VIN1 pin groups, removed unneeded empty lines, fixed VIN1 separator comment.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R8A7790/1 PFC drivers use almost identical 'union vin_data' and completely
identical VIN_DATA_PIN_GROUP() macro; we thus can move them into the shared
header file...
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When CONFIG_PM is not set we get following compilation warnings:
warning: ‘byt_gpio_runtime_suspend’ defined but not used [-Wunused-function]
warning: ‘byt_gpio_runtime_resume’ defined but not used [-Wunused-function]
Fix this by guarding byt_gpio_runtime_suspend()/byt_gpio_runtime_resume()
with #ifdef CONFIG_PM.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We get following warning when CONFIG_PM_SLEEP is not set
warning: ‘intel_gpio_irq_init’ defined but not used [-Wunused-function]
Since the function is only called from intel_pinctrl_resume() move it
inside CONFIG_PM_SLEEP guard as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DEBUG_FS=n #defines for the dbg_show functions were missed when
renaming the driver from msm_ to pm8xxx_, causing it to break the build
when DEBUG_FS isn't enabled:
CC [M] drivers/pinctrl/qcom/pinctrl-ssbi-gpio.o
drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c:597:14: error: ‘pm8xxx_gpio_dbg_show’ undeclared here (not in a function)
.dbg_show = pm8xxx_gpio_dbg_show,
Fix this by renaming them correctly.
Fixes: b4c45fe974 ("pinctrl: qcom: ssbi: Family A gpio & mpp drivers")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace all trivial request/free callbacks that do nothing but call into
pinctrl code with the generic versions.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The the pin groups and pin functions have been changed
in atlas7 step B soc. We have to update the driver
to support step B chip.
Changes:
1. add 5 jtag pins to IOC_TOP:
"jtag_tdo", "jtag_tms","jtag_tck", "jtag_tdi", "jtag_trstn"
these 5 pins can be mutiplex with other functions, so we
have to conver these 5 pins in pinmux.
2. add pin groups for audio digmic, audio spdif, can transceiver
en, can transceiver stb, i2s0, i2s1 and jtag.
3. serval pins can be located to more PADs:
audio_uart0_urfs, audio_uart1_urfs, audio_uart2_urfs,
audio_uart2_urxd, audio_uart2_usclk, audio_uart2_utfs,
audio_uart2_utxd, can0_rxd, can0_txd, can1_rxd, can1_txd
jtag_ntrst, jtag_swdiotms, jtag_tck, jtag_tdi, jtag_tdo,
pw_cko0, pw_cko1, pw_i2s01, pw_pwm0, pw_pwm1, sd2_cdb,
sd2_wpb, uart2_cts, uart2_rts, uart2_rxd, uart2_txd,
uart3_cts, uart3_rts, uart3_rxd, uart3_txd, uart4_cts,
uart4_rts, usb0_drvvbus, usb1_drvvbus.
Because of Changes#3, some functions should have more than one
pin groups. So we have to split the original pin group to serval
pin groups.
For example:
audio_uart0 has 5 pins, on STEPA, each of these 5 pins only has
one related PAD. But on STEPB, audio_uart0_urfs has 4 related
PAD.
So we place the 4 pins with one PAD into a single pin group:
audio_uart0_basic_group.
and place urfs pin wtih different PADs to 4 different pin groups:
audio_uart0_urfs_group0, ..., audio_uart0_urfs_group3
A full audio_uart0 pin group can be:
pinctrl-0 = <&audio_uart0_basic_group &audio_uart0_urfs_group0>;
If audio_uart0 pin group encountered some confiction, we only have
to change the urfs group:
pinctrl-0 = <&audio_uart0_basic_group &audio_uart0_urfs_group2>;
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The previous register layout was incorrect, many of the fields having
fewer bits than were needed to represent all their modes. The new layout
is taken from the bootloader source of a BG2CD device.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
My family name contained an accent when I submitted the
Berlin pinctrl series in the first place. There was an
encoding issue when the series was applied. Fix this.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
[Je me rendis tous les accents aigus]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Berlin pinctrl drivers depends on CONFIG_OF. This patch adds
this dependency explicitly.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch prepares to remove the pinctrl driver selection from the
mach-berlin Kconfig. To do so, bool is replaced by def_bool.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pin-controller driver for Marvell Berlin BG4CT SoC, with definition
of its groups and functions. This uses the core Berlin pinctrl driver.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is good to allow berlin pinctrl driver to build with COMPILE_TEST, so
make the it menu visible when compile-testing.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is to prepare for the next berlin4ct support, where we won't use
simple-mfd any more.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PIN_CONFIG_INPUT_SCHMITT is defined in enum_pin_config_param,
but the corresponding DT property is missing.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, the dt_params array in drivers/pinctrl/pinconf-generic.c
is not sorted in the same order as the enum pin_config_param in
include/linux/pinctrl/pinconf-generic.h.
Sort enum pin_config_param, conf_items, dt_params, alphabetically
for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Irq argument as been removed from irq flow handlers so use the irq
descriptor to retrieve data we need.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use irq_set_handler_locked() as it avoids a redundant lookup of the
irq descriptor.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
iMX7D has two iomuxc controllers, iomuxc controller similar as
previous iMX SoC generation and iomuxc-lpsr which provides low
power state rentetion capabilities on gpios that are part of
iomuxc-lpsr
Add iomuxc-lpsr gpio group id's
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add shared input select register support
- imx7d has two iomux controllers iomuxc and iomuxc-lpsr
which share select_input register for daisy chain settings
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow mux_reg offset zero to be a valid pin_id, on imx7d
mux_conf reg offset is zero for iomuxc-lspr controller
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix system chrash caused by groups whose number is smaller than the number
of groups of the last pinctl instance which is not initialized.
iMX7D supports two iomux controllers (iomuxc-lpsr and iomuxc) on probing
the second instance (iomuxc) the chrash below occurs.
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.2.0-next-20150901-00006-gebfa43c (aalonso@bluefly)
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7)
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasin instruction cache
[ 0.000000] Machine model: Freescale i.MX7 SabreSD Board
[ 0.661012] [<802a6cb0>] (strcmp) from [<802cc80c>] (imx_dt_node_to_map+0x58/0x208)
[ 0.668879] [<802cc80c>] (imx_dt_node_to_map) from [<802cbe24>] (pinctrl_dt_to_map+0x174/0x2b0)
[ 0.677654] [<802cbe24>] (pinctrl_dt_to_map) from [<802c8f18>] (pinctrl_get+0x100/0x424)
[ 0.685878] [<802c8f18>] (pinctrl_get) from [<802c9510>] (pinctrl_register+0x26c/0x480)
[ 0.694104] [<802c9510>] (pinctrl_register) from [<802ccf3c>] (imx_pinctrl_probe+0x580/0x6e8)
[ 0.702706] [<802ccf3c>] (imx_pinctrl_probe) from [<80351b58>] (platform_drv_probe+0x44/0xa4)
[ 0.711455] [<80351b58>] (platform_drv_probe) from [<803503ec>] (driver_probe_device+0x174/0x2b4)
[ 0.720405] [<803503ec>] (driver_probe_device) from [<803505fc>] (__driver_attach+0x8c/0x90)
[ 0.728982] [<803505fc>] (__driver_attach) from [<8034e930>] (bus_for_each_dev+0x6c/0xa0)
[ 0.737381] [<8034e930>] (bus_for_each_dev) from [<8034fb88>] (bus_add_driver+0x148/0x1f0)
[ 0.745804] [<8034fb88>] (bus_add_driver) from [<80350c00>] (driver_register+0x78/0xf8)
[ 0.753880] [<80350c00>] (driver_register) from [<800097d0>] (do_one_initcall+0x8c/0x1d4)
[ 0.762282] [<800097d0>] (do_one_initcall) from [<80987dac>] (kernel_init_freeable+0x144/0x1e4)
[ 0.771061] [<80987dac>] (kernel_init_freeable) from [<806d9c7c>] (kernel_init+0x8/0xe8)
[ 0.779285] [<806d9c7c>] (kernel_init) from [<8000f628>] (ret_from_fork+0x14/0x2c)
[ 0.786981] Code: e3520000 e5e32001 1afffffb e12fff1e (e4d03001)
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
