It does not make sense to create an anycast address for an /128-prefix.
Suppress it.
As 32019e651c ("ipv6: Do not leave router anycast address for /127
prefixes.") shows we also may not leave them, because we could accidentally
remove an anycast address the user has allocated or got added via another
prefix.
Cc: François-Xavier Le Bail <fx.lebail@yahoo.com>
Cc: Thomas Haller <thaller@redhat.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing serial state notification handling expected older Option
devices, having a hardcoded assumption that the Modem port was always
USB interface #2. That isn't true for devices from the past few years.
hso_serial_state_notification is a local cache of a USB Communications
Interface Class SERIAL_STATE notification from the device, and the
USB CDC specification (section 6.3, table 67 "Class-Specific Notifications")
defines wIndex as the USB interface the event applies to. For hso
devices this will always be the Modem port, as the Modem port is the
only port which is set up to receive them by the driver.
So instead of always expecting USB interface #2, instead validate the
notification with the actual USB interface number of the Modem port.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With arm:allmodconfig, building the Teles PCI driver fails with
telespci.c:294:2: error: #error "not running on big endian machines now"
Similar, building the driver for HFC PCI-Bus cards fails with
hfc_pci.c:1647:2: error: #error "not running on big endian machines now"
Remove the big endian cpp check from both drivers to fix the build errors.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla says:
====================
be2net: patch set
Pls apply the following bug fixes to the 'net' tree. Thanks.
Suresh Reddy (2):
be2net: increase the timeout value for loopback-test FW cmd
be2net: fix max_evt_qs calculation for BE3 in SR-IOV config
Vasundhara Volam (1):
be2net: disable RSS when number of RXQs is reduced to 1 via
set-channels
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver wrongly assumes 16 EQs/vectors are available for each BE3 PF.
When SR-IOV is enabled, a BE3 PF can support only a max of 8 EQs.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The loopback test FW cmd may need upto 15 seconds to complete on
certain PHYs. This patch also fixes the name of the completion variable
used to synchronize FW cmd completions as it not used by the flashing
cmd alone anymore.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When *only* the default RXQ is used, the RSS policy must be disabled so
that all IP and no-IP traffic is placed into the default RXQ. If not,
IP traffic is dropped.
Also, issue the RSS_CONFIG cmd only if FW advertises RSS capability for
the interface.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ac3d5ac277 ("xen-netback: fix guest-receive-side array sizes")
added calls to vmalloc and vfree in the interface.c file without including
<linux/vmalloc.h>. This causes build failures if the
-Werror=implicit-function-declaration flag is passed.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function lowpan_header_create(), we invoke the following code
construct:
struct ipv6hdr *hdr;
...
hdr = ipv6_hdr(skb);
...
if (...)
memcpy(hc06_ptr + 1, &hdr->flow_lbl[1], 2);
else
memcpy(hc06_ptr, &hdr, 4);
Where the else path of the condition, that is, non-compression
path, calls memcpy() with a pointer to struct ipv6hdr *hdr as
source, thus two levels of indirection. This cannot be correct,
and likely only one level of pointer was intended as source
buffer for memcpy() here.
Fixes: 44331fe2aa ("IEEE802.15.4: 6LoWPAN basic support")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to keep DT compatibility we need to revert this, otherwise the original
dts files will no longer work with this driver change.
This reverts commit 7a399e3a2e.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
bnx2x: Bug fixes patch series
Most of what this parch series contains is SR-IOV related bug fixes.
Additionally, it contains some small fixes for legacy devices/modes.
Please consider applying these patches to `net'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hypervisor configures a vlan for the VF via the PF, the expected
result is that only packets tagged by said vlan will be received by the VF
(and that vlan will be silently removed).
Due to an incorrect manipulation of vlan filters in the driver, the
VF can receive untagged traffic even if the hypervisor configured
some vlan for it.
This patch corrects the behaviour.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 different (related) flows in the slowpath configuration
that utilize the same pointer and cast it to different structs;
This is obviously incorrect as the intended allocated memory is that
of the smaller struct, possibly causing the flow utilizing the larger
struct to corrupt other slowpath configuration.
Since both flows are exclusive, set the allocated memory to be a union
of both structs.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PF receives a VF message indicating a change in RSS properties
it should clean the flags' bit-fields; Otherwise, it's possible that
some random values will be considered as flags by the lower layers configuring
the RSS in FW.
Signed-off-by: Michal Kalderon <michals@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of VFs in PCIe configuration space is zero-based. Driver incorrectly
sets the number of VFs to be larger by one than what actually is feasible by
HW, which might cause later VFs to fail to allocate their MSI-X interrupts.
Signed-off-by: Michal Kalderon <michals@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original straightforward division may lead to zeroing number of SB and
null-pointer dereference when device is short of MSIX vectors or lacks
MSIX capabilities.
Reported-by: Vladislav Zolotarov <vladz@cloudius-systems.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver is using common tx_clean_lock for all Tx queues. This patch
adds per queue tx_clean_lock.
o Driver is not updating sw_consumer while processing Tx completion
when interface is going down. Fixed in this patch.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we create a new infiniband link with uninfiniband device, e.g. `ip link
add link em1 type ipoib pkey 0x8001`. We will get a NULL pointer dereference
cause other dev like Ethernet don't have struct ib_device.
The code path is:
rtnl_newlink
|-- ipoib_new_child_link
|-- __ipoib_vlan_add
|-- ipoib_set_dev_features
|-- ib_query_device
Fix this bug by make sure the src net is infiniband when create new link.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 52367a763d
("cxgb4/cxgb4vf: Code cleanup to enable T4 Configuration File support"),
we have failures like this during cxgb4 probe:
cxgb4 0000:01:00.4: bad SGE FL page buffer sizes [65536, 65536]
cxgb4: probe of 0000:01:00.4 failed with error -22
This happens whenever software parameters are used, without a
configuration file. That happens when the hardware was already
initialized (after kexec, or after csiostor is loaded).
It happens that these values are acceptable, rendering fl_pg_order equal
to 0, which is the case of a hard init when the page size is equal or
larger than 65536.
Accepting fl_large_pg equal to fl_small_pg solves the issue, and
shouldn't cause any trouble besides a possible performance reduction
when smaller pages are used. And that can be fixed by a configuration
file.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VLAN tag handling code in netpoll_send_skb_on_dev() has two problems.
1) It exits without unlocking the TXQ.
2) It then tries to queue a NULL skb to npinfo->txq.
Reported-by: Ahmed Tamrawi <atamrawi@iastate.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
when read/write the 64bit data, the correct lock should be hold.
and we can use the generic vti6_get_stats to return stats, and
not define a new one in ip6_vti.c
Fixes: 87b6d218f3 ("tunnel: implement 64 bits statistics")
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when read/write the 64bit data, the correct lock should be hold.
Fixes: 87b6d218f3 ("tunnel: implement 64 bits statistics")
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a problem with setting the lifetime of an IPv6
address. When setting preferred_lft to a value not zero or
infinity, while valid_lft is infinity(0xffffffff) preferred
lifetime is set to forever and does not update. Therefore
preferred lifetime never becomes deprecated. valid lifetime
and preferred lifetime should be set independently, even if
valid lifetime is infinity, preferred lifetime must expire
correctly (meaning it must eventually become deprecated)
Signed-off-by: Yasushi Asano <yasushi.asano@jp.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While commit 30a584d944 fixes datagram interface in LLC, a use
after free bug has been introduced for SOCK_STREAM sockets that do
not make use of MSG_PEEK.
The flow is as follow ...
if (!(flags & MSG_PEEK)) {
...
sk_eat_skb(sk, skb, false);
...
}
...
if (used + offset < skb->len)
continue;
... where sk_eat_skb() calls __kfree_skb(). Therefore, cache
original length and work on skb_len to check partial reads.
Fixes: 30a584d944 ("[LLX]: SOCK_DGRAM interface fixes")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
During restoring, try_fill_recv() was called with neither napi lock nor napi
disabled. This can lead two try_fill_recv() was called in the same time. Fix
this by refilling before trying to enable napi.
Fixes 0741bcb558
(virtio: net: Add freeze, restore handlers to support S4).
Cc: Amit Shah <amit.shah@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VM to VM GSO traffic is broken if it goes through VXLAN or GRE
tunnel and the physical NIC on the host supports hardware VXLAN/GRE
GSO offload (e.g. bnx2x and next-gen mlx4).
Two issues -
(VXLAN) VM traffic has SKB_GSO_DODGY and SKB_GSO_UDP_TUNNEL with
SKB_GSO_TCP/UDP set depending on the inner protocol. GSO header
integrity check fails in udp4_ufo_fragment if inner protocol is
TCP. Also gso_segs is calculated incorrectly using skb->len that
includes tunnel header. Fix: robust check should only be applied
to the inner packet.
(VXLAN & GRE) Once GSO header integrity check passes, NULL segs
is returned and the original skb is sent to hardware. However the
tunnel header is already pulled. Fix: tunnel header needs to be
restored so that hardware can perform GSO properly on the original
packet.
Signed-off-by: Wei-Chun Chao <weichunc@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP outqueue structure maintains a data chunks
that are pending transmission, the list of chunks that
are pending a retransmission and a length of data in
flight. It also tries to keep the emtpy state so that
it can performe shutdown sequence or notify user.
The problem is that the empy state is inconsistently
tracked. It is possible to completely drain the queue
without sending anything when using PR-SCTP. In this
case, the empty state will not be correctly state as
report by Jamal Hadi Salim <jhs@mojatatu.com>. This
can cause an association to be perminantly stuck in the
SHUTDOWN_PENDING state.
Additionally, SCTP is incredibly inefficient when setting
the empty state. Even though all the data is availaible
in the outqueue structure, we ignore it and walk a list
of trasnports.
In the end, we can completely remove the extra empty
state and figure out if the queue is empty by looking
at 3 things: length of pending data, length of in-flight
data, and exisiting of retransmit data. All of these
are already in the strucutre.
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o TX queues allocation was getting distributed equally among all the
functions of the port including VFs and PF. Which was leading to failure
in PF's multiple TX queues creation.
o Instead of dividing queues equally allocate one TX queue for each VF as VF
doesn't support multiple TX queues.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Adapter requires that if the port is in loopback mode no traffic should
be flowing through that port, so on arrival of Link up AEN, do not advertise
Link up to the stack until port is out of loopback mode
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when read/write the 64bit data, the correct lock should be hold.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function llc_conn_ac_inc_vr_by_1() evaluates via macro
PDU_GET_NEXT_Vr() into ...
llc_sk(sk)->vR = ++llc_sk(sk)->vR & 0xffffffffffffff7f
... but the order in which the side effects take place is
undefined because there is no intervening sequence point.
As llc_sk(sk)->vR is written in llc_sk(sk)->vR (assignment
left-hand side) and written in ++llc_sk(sk)->vR & 0xffffffffffffff7f
this might possibly yield undefined behavior.
The final value of llc_sk(sk)->vR is ambiguous, because,
depending on the order of expression evaluation, the
increment may occur before, after, or interleaved with
the assignment. In C, evaluating such an expression yields
undefined behavior.
Since we're doing the increment via PDU_GET_NEXT_Vr() macro
and the only place it is being used is from
llc_conn_ac_inc_vr_by_1(), in order to increment vR by 1
with a follow-up optimized modulo, rewrite the expression
into ((vR + 1) & CONST) in order to fix this.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
KR2 work-around is based on detecting non-KR2 devices which may not link up
in this mode. One such link-partner is the BCM8073 which has specific
advertisement characteristics in specific mode, and this condition was not set
correctly.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a problem where link is reported to be up when SFP+ module is plugged in
without cable. This occurs with specific module types which may generate
temporary TX_FAULT indication. Solution is to avoid changing any link parameters
when checking TX_FAULT indication while physical link is down.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM54618SE is used to advertise half-duplex even if HD was not requested by the
user. This change makes the legacy speed/duplex advertisement for this PHY
exactly according to the requested speed and duplex.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix Passive DAC detection for specific cables, such that even in case
SFP_CABLE_TECHNOLOGY option is not set in the EEPROM (offset 8), treat it as a
passive DAC cable, since some cables don't have this indication.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a problem where 578xx-KR is unable to get link when connected to 1G link
partner. Two fixes were required:
One was to force CL37 sync_status low to prevent Warpcore from getting stuck in
CL73 parallel detect loop while link partner is sending.
Second fix was to enable auto-detect mode, thus allowing the Warpcore to select
the higher speed protocol between 10G-KR (over CL73), or go down to 1G over CL73
when there's indication for it.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even with the quirks in commit dabdaf0c (mcs7830: Fix link state
detection) there are still spurious link-down events for some chips
where the false link-down events count go over a few hundreds.
This patch takes a more conservative approach and only looks at
link-down events where the link-down state is not combined with other
states (e.g. half/full speed, pending frames in SRAM or TX status
information valid). In all other cases we assume the link is up.
Tested on MCS7830CV-DA (USB ID 9710:7830).
Cc: Ondrej Zary <linux@rainbow-software.org>
Cc: Michael Leun <lkml20120218@newton.leun.net>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the vlan code detects that the real device can do TX VLAN offloads
in hardware, it tries to arrange for the real device's header_ops to
be invoked directly.
But it does so illegally, by simply hooking the real device's
header_ops up to the VLAN device.
This doesn't work because we will end up invoking a set of header_ops
routines which expect a device type which matches the real device, but
will see a VLAN device instead.
Fix this by providing a pass-thru set of header_ops which will arrange
to pass the proper real device instead.
To facilitate this add a dev_rebuild_header(). There are
implementations which provide a ->cache and ->create but not a
->rebuild (f.e. PLIP). So we need a helper function just like
dev_hard_header() to avoid crashes.
Use this helper in the one existing place where the
header_ops->rebuild was being invoked, the neighbour code.
With lots of help from Florian Westphal.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc fixes from Ben Herrenschmidt:
"A bit more endian problems found during testing of 3.13 and a few
other simple fixes and regressions fixes"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix alignment of secondary cpu spin vars
powerpc: Align p_end
powernv/eeh: Add buffer for P7IOC hub error data
powernv/eeh: Fix possible buffer overrun in ioda_eeh_phb_diag()
powerpc: Make 64-bit non-VMX __copy_tofrom_user bi-endian
powerpc: Make unaligned accesses endian-safe for powerpc
powerpc: Fix bad stack check in exception entry
powerpc/512x: dts: disable MPC5125 usb module
powerpc/512x: dts: remove misplaced IRQ spec from 'soc' node (5125)
Pull networking fixes from David Miller:
"Some holiday bug fixes for 3.13... There is still one bug I'd like to
get fixed before 3.13-final.
The vlan code erroneously assignes the header ops of the underlying
real device to the VLAN device above it when the real device can
hardware offload VLAN handling. That's completely bogus because
header ops are tied to the device type, so they only expect to see a
'dev' argument compatible with their ops.
The fix is the have the VLAN code use a special set of header ops that
does the pass-thru correctly, by calling the underlying real device's
header ops but _also_ passing in the real device instead of the VLAN
device.
That fix is currently waiting some testing.
Anyways, of note here:
1) Fix bitmap edge case in radiotap, from Johannes Berg.
2) Fix oops on driver unload in rtlwifi, from Larry Finger.
3) Bonding doesn't do locking correctly during speed/duplex/link
changes, from Ding Tianhong.
4) Fix header parsing in GRE code, this bug has been around for a few
releases. From Timo Teräs.
5) SIT tunnel driver MTU check needs to take GSO into account, from
Eric Dumazet.
6) Minor info leak in inet_diag, from Daniel Borkmann.
7) Info leak in YAM hamradio driver, from Salva Peiró.
8) Fix route expiration state handling in ipv6 routing code, from Li
RongQing.
9) DCCP probe module does not check request_module()'s return value,
from Wang Weidong.
10) cpsw driver passes NULL device names to request_irq(), from
Mugunthan V N.
11) Prevent a NULL splat in RDS binding code, from Sasha Levin.
12) Fix 4G overflow test in tg3 driver, from Nithin Sujir.
13) Cure use after free in arc_emac and fec driver's software
timestamp handling, from Eric Dumazet.
14) SIT driver can fail to release the route when
iptunnel_handle_offloads() throws an error. From Li RongQing.
15) Several batman-adv fixes from Simon Wunderlich and Antonio
Quartulli.
16) Fix deadlock during TIPC socket release, from Ying Xue.
17) Fix regression in ROSE protocol recvmsg() msg_name handling, from
Florian Westphal.
18) stmmac PTP support releases wrong spinlock, from Vince Bridgers"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
stmmac: Fix incorrect spinlock release and PTP cap detection.
phy: IRQ cannot be shared
net: rose: restore old recvmsg behavior
xen-netback: fix guest-receive-side array sizes
fec: Do not assume that PHY reset is active low
tipc: fix deadlock during socket release
netfilter: nf_tables: fix wrong datatype in nft_validate_data_load()
batman-adv: fix vlan header access
batman-adv: clean nf state when removing protocol header
batman-adv: fix alignment for batadv_tvlv_tt_change
batman-adv: fix size of batadv_bla_claim_dst
batman-adv: fix size of batadv_icmp_header
batman-adv: fix header alignment by unrolling batadv_header
batman-adv: fix alignment for batadv_coded_packet
netfilter: nf_tables: fix oops when updating table with user chains
netfilter: nf_tables: fix dumping with large number of sets
ipv6: release dst properly in ipip6_tunnel_xmit
netxen: Correct off-by-one errors in bounds checks
net: Add some clarification to skb_tx_timestamp() comment.
arc_emac: fix potential use after free
...
Commit 2361613206, "of/irq: Refactor interrupt-map parsing" changed
the refcount on the device_node causing an error in of_node_put():
ERROR: Bad of_node_put() on /pci@800000020000000
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.13.0-rc3-dirty #2
Call Trace:
[c00000003e403500] [c0000000000144fc] .show_stack+0x7c/0x1f0 (unreliable)
[c00000003e4035d0] [c00000000070f250] .dump_stack+0x88/0xb4
[c00000003e403650] [c0000000005e8768] .of_node_release+0xd8/0xf0
[c00000003e4036e0] [c0000000005eeafc] .of_irq_parse_one+0x10c/0x280
[c00000003e4037a0] [c0000000005efd4c] .of_irq_parse_pci+0x3c/0x1d0
[c00000003e403840] [c000000000038240] .pcibios_setup_device+0xa0/0x2e0
[c00000003e403910] [c0000000000398f0] .pcibios_setup_bus_devices+0x60/0xd0
[c00000003e403990] [c00000000003b3a4] .__of_scan_bus+0x1a4/0x2b0
[c00000003e403a80] [c00000000003a62c] .pcibios_scan_phb+0x30c/0x410
[c00000003e403b60] [c0000000009fe430] .pcibios_init+0x7c/0xd4
This patch adjusts the refcount in the walk of the interrupt tree.
When a match is found, there is no need to increase the refcount
on 'out_irq->np' as 'newpar' is already holding a ref. The refcount
balance between 'ipar' and 'newpar' is maintained in the skiplevel:
goto label.
This patch also removes the usage of the device_node variable 'old'
which seems useless after the latest changes.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This reverts commit e38c0a1fbc.
Nikita Yushchenko reports:
While trying to make freescale p2020ds and mpc8572ds boards working
with mainline kernel, I faced that commit e38c0a1f (Handle
Both these boards have uli1575 chip.
Corresponding part in device tree is something like
uli1575@0 {
reg = <0x0 0x0 0x0 0x0 0x0>;
#size-cells = <2>;
#address-cells = <3>;
ranges = <0x2000000 0x0 0x80000000
0x2000000 0x0 0x80000000
0x0 0x20000000
0x1000000 0x0 0x0
0x1000000 0x0 0x0
0x0 0x10000>;
isa@1e {
...
I.e. it has #address-cells = <3>
With commit e38c0a1f reverted, devices under uli1575 are registered
correctly, e.g. for rtc
OF: ** translation for device /pcie@ffe09000/pcie@0/uli1575@0/isa@1e/rtc@70 **
OF: bus is isa (na=2, ns=1) on /pcie@ffe09000/pcie@0/uli1575@0/isa@1e
OF: translating address: 00000001 00000070
OF: parent bus is default (na=3, ns=2) on /pcie@ffe09000/pcie@0/uli1575@0
OF: walking ranges...
OF: ISA map, cp=0, s=1000, da=70
OF: parent translation for: 01000000 00000000 00000000
OF: with offset: 70
OF: one level translation: 00000000 00000000 00000070
OF: parent bus is pci (na=3, ns=2) on /pcie@ffe09000/pcie@0
OF: walking ranges...
OF: default map, cp=a0000000, s=20000000, da=70
OF: default map, cp=0, s=10000, da=70
OF: parent translation for: 01000000 00000000 00000000
OF: with offset: 70
OF: one level translation: 01000000 00000000 00000070
OF: parent bus is pci (na=3, ns=2) on /pcie@ffe09000
OF: walking ranges...
OF: PCI map, cp=0, s=10000, da=70
OF: parent translation for: 01000000 00000000 00000000
OF: with offset: 70
OF: one level translation: 01000000 00000000 00000070
OF: parent bus is default (na=2, ns=2) on /
OF: walking ranges...
OF: PCI map, cp=0, s=10000, da=70
OF: parent translation for: 00000000 ffc10000
OF: with offset: 70
OF: one level translation: 00000000 ffc10070
OF: reached root node
With commit e38c0a1f in place, address translation fails:
OF: ** translation for device /pcie@ffe09000/pcie@0/uli1575@0/isa@1e/rtc@70 **
OF: bus is isa (na=2, ns=1) on /pcie@ffe09000/pcie@0/uli1575@0/isa@1e
OF: translating address: 00000001 00000070
OF: parent bus is default (na=3, ns=2) on /pcie@ffe09000/pcie@0/uli1575@0
OF: walking ranges...
OF: ISA map, cp=0, s=1000, da=70
OF: parent translation for: 01000000 00000000 00000000
OF: with offset: 70
OF: one level translation: 00000000 00000000 00000070
OF: parent bus is pci (na=3, ns=2) on /pcie@ffe09000/pcie@0
OF: walking ranges...
OF: default map, cp=a0000000, s=20000000, da=70
OF: default map, cp=0, s=10000, da=70
OF: not found !
Thierry Reding confirmed this commit was not needed after all:
"We ended up merging a different address representation for Tegra PCIe
and I've confirmed that reverting this commit doesn't cause any obvious
regressions. I think all other drivers in drivers/pci/host ended up
copying what we did on Tegra, so I wouldn't expect any other breakage
either."
There doesn't appear to be a simple way to support both behaviours, so
reverting this as nothing should be depending on the new behaviour.
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Rob Herring <robh@kernel.org>
This patch corrects a problem in stmmac_ptp.c, functions
stmmac_adjust_time and stmmac_adjust_freq where the incorrect spinlocks
were released. This patch also addresses a problem in stmmac_main,
function stmmac_init_ptp where the capability detection for
advanced timestamping was masked by message masking.
This patch was touch tested using linuxptp, and runs without the previously
observed instabilities. More extensive testing is ongoing.
Vince
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the way PHY IRQ handler is implemented (all real handling being pushed to
the workqueue and returning IRQ_HANDLED all the time PHY is active), we cannot
really claim that PHY IRQ can be shared when calling request_irq().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
