Add a new ice_ptp.c file for holding the basic PTP clock interface
functions. If the device supports PTP, call the new ice_ptp_init and
ice_ptp_release functions where appropriate.
If the function owns the hardware resource associated with the PTP
hardware clock, register with the PTP_1588_CLOCK infrastructure to
allocate a new clock object that represents the device hardware clock.
Implement basic functionality for reading and setting the clock time,
performing clock adjustments, and adjusting the clock frequency.
Future changes will introduce functionality for handling related
features including Tx and Rx timestamps.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the ice_ptp_hw.c file and some associated definitions to the ice
driver folder. This file contains basic low level definitions for
functions that interact with the device hardware.
For now, only E810-based devices are supported. The ice hardware
supports 2 major variants which have different PHYs with different
procedures necessary for interacting with the device clock.
Because the device captures timestamps in the PHY, each PHY has its own
internal timer. The timers are synchronized in hardware by first
preparing the source timer and the PHY timer shadow registers, and then
issuing a synchronization command. This ensures that both the source
timer and PHY timers are programmed simultaneously. The timers
themselves are all driven from the same oscillator source.
The functions in ice_ptp_hw.c abstract over the differences between how
the PHYs in E810 are programmed vs how the PHYs in E822 devices are
programmed. This series only implements E810 support, but E822 support
will be added in a future change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Depending on the device configuration, the ice hardware may share the
PTP hardware clock timer between multiple PFs. Each PF is informed by
firmware during initialization of the PTP timer association.
When bringing up PTP, only the PFs which own the timer shall allocate
a PTP hardware clock. Other PFs associated with that timer must report
the correct PTP clock index in order to allow userspace software the
ability to know which ports are connected to the same clock.
To support this, the firmware has driver shared parameters. These
parameters enable one PF to write the clock index into firmware, and
have other PFs read the associated value out. This enables the driver to
have only a single PF allocate and control the device timer registers,
while other PFs associated with that timer can report the correct clock
in the ETHTOOL_GET_TS_INFO report.
Add support for the necessary admin queue commands to enable reading and
writing of the driver shared parameters. This will be used in a future
change to enable sharing the PTP clock index between PF drivers.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The device firmware reports PTP clock capabilities to each PF during
initialization. This includes various information for both the overall
device and the individual function, including
For functions:
* whether this function has timesync enabled
* whether this function owns one of the 2 possible clock timers, and
which one
* which timer the function is associated with
* the clock frequency, if the device supports multiple clock frequencies
* The GPIO pin association for the timer owned by this PF, if any
For the device:
* Which PF owns timer 0, if any
* Which PF owns timer 1, if any
* whether timer 0 is enabled
* whether timer 1 is enabled
Extract the bits from the capabilities information reported by firmware
and store them in the device and function capability structures.o
This information will be used in a future change to have the function
driver enable PTP hardware clock support.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In order to support certain device features, including enabling the PTP
hardware clock, the ice driver needs to control some registers on the
device PHY.
These registers are accessed by sending sideband messages. For some
hardware, these messages must be sent over the device admin queue, while
other hardware has a dedicated control queue for the sideband messages.
Add the neighbor device message structure for sending a message to the
neighboring device. Where supported, initialize the sideband control
queue and handle cleanup.
Add a wrapper function for sending sideband control queue messages that
read or write a neighboring device register.
Because some devices send sideband messages over the AdminQ, also
increase the length of the admin queue to allow more messages to be
queued up. This is important because the sideband messages add
additional pressure on the AQ usage.
This support will be used in following patches to enable support for
CONFIG_1588_PTP_CLOCK.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit ae15e0ba1b ("ice: Change number of XDP Tx queues to match
number of Rx queues") tried to address the incorrect setting of XDP
queue count that was based on the Tx queue count, whereas in theory we
should provide the XDP queue per Rx queue. However, the routines that
setup and destroy the set of Tx resources are still based on the
vsi->num_txq.
Ice supports the asynchronous Tx/Rx queue count, so for a setup where
vsi->num_txq > vsi->num_rxq, ice_vsi_stop_tx_rings and ice_vsi_cfg_txqs
will be accessing the vsi->xdp_rings out of the bounds.
Parameterize two mentioned functions so they get the size of Tx resources
array as the input.
Fixes: ae15e0ba1b ("ice: Change number of XDP Tx queues to match number of Rx queues")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice driver requires a programmable pipeline firmware package in order to
have a support for advanced features. Otherwise, driver falls back to so
called 'safe mode'. For that mode, ndo_bpf callback is not exposed and
when user tries to load XDP program, the following happens:
$ sudo ./xdp1 enp179s0f1
libbpf: Kernel error message: Underlying driver does not support XDP in native mode
link set xdp fd failed
which is sort of confusing, as there is a native XDP support, but not in
the current mode. Improve the user experience by providing the specific
ndo_bpf callback dedicated for safe mode which will make use of extack
to explicitly let the user know that the DDP package is missing and
that's the reason that the XDP can't be loaded onto interface currently.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Fixes: efc2214b60 ("ice: Add support for XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-06-07
This series contains updates to virtchnl header file and ice driver.
Brett adds capability bits to virtchnl to specify whether a primary or
secondary MAC address is being requested and adds the implementation to
ice. He also adds storing of VF MAC address so that it will be preserved
across reboots of VM and refactors VF queue configuration to remove the
expectation that configuration be done all at once.
Krzysztof refactors ice_setup_rx_ctx() to remove configuration not
related to Rx context into a new function, ice_vsi_cfg_rxq().
Liwei Song extends the wait time for the global config timeout.
Salil Mehta refactors code in ice_vsi_set_num_qs() to remove an
unnecessary call when the user has requested specific number of Rx or Tx
queues.
Jesse converts define macros to static inlines for NOP configurations.
Jake adds messaging when devlink fails to read device capabilities and
when pldmfw cannot find the requested firmware. Adds a wait for reset
completion when reporting devlink info and reinitializes NVM during
rebuild to ensure values are current.
Ani adds detection and reporting of modules exceeding supported power
levels and changes an error message to a debug message.
Paul fixes a clang warning for deadcode.DeadStores.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
clang generates deadcode.DeadStores warnings when a variable
is used to read a value, but then that value isn't used later
in the code. Fix this warning.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Failing to add or remove LLDP filter doesn't seem to be a fatal
error, so downgrade the dev_err message to a dev_dbg message.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Determine whether an unsupported power configuration is preventing link
establishment by storing and checking the link_cfg_err_byte. Print error
messages when module power levels are unsupported. Also add a new flag
bit to prevent spamming said error messages.
Co-developed-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After performing a flash update, a device EMP reset may occur. This
reset will cause the newly downloaded firmware to be initialized. When
this happens, the driver still reports the previous NVM version
information.
This is because the NVM versions are cached within the hw structure.
This can be confusing, as the new firmware is in fact running in this
case.
Handle this by calling ice_init_nvm when rebuilding the driver state.
This will update the flash version information and ensures that the
current values are displayed when reporting the NVM versions to the
stack.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Requesting device firmware information while the device is busy cleaning
up after a reset can result in an unexpected failure:
This occurs because the command is attempting to access the device
AdminQ while it is down. Resolve this by having the command wait for
a while until the reset is complete. To do this, introduce
a reset_wait_queue and associated helper function "ice_wait_for_reset".
This helper will use the wait queue to sleep until the driver is done
rebuilding. Use of a wait queue is preferred because the potential sleep
duration can be several seconds.
To ensure that the thread wakes up properly, a new wake_up call is added
during all code paths which clear the reset state bits associated with
the driver rebuild flow.
Using this ensures that tools can request device information without
worrying about whether the driver is cleaning up from a reset.
Specifically, it is expected that a flash update could result in
a device reset, and it is better to delay the response for information
until the reset is complete rather than exit with an immediate failure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When flashing a new firmware image onto the device, the pldmfw library
parses the image contents looking for a matching record. If no record
can be found, the function reports an error of -ENOENT. This can produce
a very confusing error message and experience for the user:
$devlink dev flash pci/0000🆎00.0 file image.bin
devlink answers: No such file or directory
This is because the ENOENT error code is interpreted as a missing file
or directory. The pldmfw library does not have direct access to the
extack pointer as it is generic and non-netdevice specific. The only way
that ENOENT is returned by the pldmfw library is when no record matches.
Catch this specific error and report a suitable extended ack message:
$devlink dev flash pci/0000🆎00.0 file image.bin
Error: ice: Firmware image has no record matching this device
devlink answers: No such file or directory
In addition, ensure that we log an error message to the console whenever
this function fails. Because our driver specific PLDM operation
functions potentially set the extended ACK message, avoid overwriting
this with a generic message.
This change should result in an improved experience when attempting to
flash an image that does not have a compatible record.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When filling out information for the DEVLINK_CMD_INFO_GET, the driver
needs to read some device capabilities. Add an extack message to
properly inform the caller of the failure, as we do for other failures
in this function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Trivial:
The driver had previously attempted to use #define
macros to make functions that have no use in certain
configs disappear. Using static inlines instead allows
for certain static checkers to process the code better,
and results in no functional change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If user has explicitly requested the number of {R,T}XQs, then it is
unnecessary to get the count of already available {R,T}XQs from the
PF avail_{r,t}xqs bitmap. This value will get overridden by user specified
value in any case.
Re-organize this code for improving the flow, readability and efficiency.
This scope of improvement was found during the review of the ICE driver
code.
Fixes: 87324e747f ("ice: Implement ethtool ops for channels")
Cc: intel-wired-lan@lists.osuosl.org
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It may need hold Global Config Lock a longer time when download DDP
package file, extend the timeout value to 5000ms to ensure that
download can be finished before other AQ command got time to run,
this will fix the issue below when probe the device, 5000ms is a test
value that work with both Backplane and BreakoutCable NVM image:
ice 0000:f4:00.0: VSI 12 failed lan queue config, error ICE_ERR_CFG
ice 0000:f4:00.0: Failed to delete VSI 12 in FW - error: ICE_ERR_AQ_TIMEOUT
ice 0000:f4:00.0: probe failed due to setup PF switch: -12
ice: probe of 0000:f4:00.0 failed with error -12
Signed-off-by: Liwei Song <liwei.song@windriver.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, when a VF requests queue configuration via
VIRTCHNL_OP_CONFIG_VSI_QUEUES the PF driver expects that this message
will only be called once and we always assume the queues being
configured start from 0. This is incorrect and is causing issues when
a VF tries to send this message for multiple queue blocks. Fix this by
using the queue_id specified in the virtchnl message and allowing for
individual Rx and/or Tx queues to be configured.
Also, reduce the duplicated for loops for configuring the queues by
moving all the logic into a single for loop.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Move AF_XDP logic and buffer allocation out of ice_setup_rx_ctx() to a
new function ice_vsi_cfg_rxq(), so the function actually sets up the Rx
context.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Co-developed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
If a VM reboots and/or VF driver is unloaded, its cached hardware MAC
address (hw_lan_addr.addr) is cleared in some cases. If the VF is
trusted, then the PF driver allows the VF to clear its old MAC address
even if this MAC was configured by a host administrator. If the VF is
untrusted, then the PF driver allows the VF to clear its old MAC
address only if the host admin did not set it.
For the trusted VF case, this is unexpected and will cause issues
because the host configured MAC (i.e. via XML) will be cleared on VM
reboot. For the untrusted VF case, this is done to be consistent and it
will allow the VF to keep the same MAC across VM reboot.
Fix this by introducing dev_lan_addr to the VF structure. This will be
the VF's MAC address when it's up and running and in most cases will be
the same as the hw_lan_addr. However, to address the VM reboot and
unload/reload problem, the driver will never allow the hw_lan_addr to be
cleared via VIRTCHNL_OP_DEL_ETH_ADDR. When the VF's MAC is changed, the
dev_lan_addr and hw_lan_addr will always be updated with the same value.
The only ways the VF's MAC can change are the following:
- Set the VF's MAC administratively on the host via iproute2.
- If the VF is trusted and changes/sets its own MAC.
- If the VF is untrusted and the host has not set the MAC via iproute2.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently there is no way for a VF driver to specify if it wants to
change it's hardware address. New bits are being added to virtchnl.h
in struct virtchnl_ether_addr that allow for the VF to correctly
communicate this information. However, legacy VF drivers that don't
support the new virtchnl.h bits still need to be supported. Make a
best effort attempt at saving the VF's primary/device address in the
legacy case and depend on the VIRTCHNL_ETHER_ADDR_PRIMARY type for
the new case.
Legacy case - If a unicast MAC is being added and the
hw_lan_addr.addr is empty, then populate it. This assumes that the
address is the VF's hardware address. If a unicast MAC is being
added and the hw_lan_addr.addr is not empty, then cache it in the
legacy_last_added_umac.addr. If a unicast MAC is being deleted and it
matches the hw_lan_addr.addr, then zero the hw_lan_addr.addr.
Also, if the legacy_last_added_umac.addr has not expired, copy the
legacy_last_added_umac.addr into the hw_lan_addr.addr. This is done
because we cannot guarantee the order of VIRTCHNL_OP_ADD_ETH_ADDR and
VIRTCHNL_OP_DEL_ETH_ADDR.
New case - If a unicast MAC is being added and it's specified as
VIRTCHNL_ETHER_ADDR_PRIMARY, then replace the current
hw_lan_addr.addr. If a unicast MAC is being deleted and it's type
is specified as VIRTCHNL_ETHER_ADDR_PRIMARY, then zero the
hw_lan_addr.addr.
Untrusted VFs - Only allow above legacy/new changes to their
hardware address if the PF has not set it administratively via
iproute2.
Trusted VFs - Always allow above legacy/new changes to their
hardware address even if the PF has administratively set it via
iproute2.
Also, change the variable dflt_lan_addr to hw_lan_addr to clearly
represent the purpose of this variable since it's purpose is to
act as a hardware programmed MAC address for the VF.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently in the ice driver, the check whether to
allow a LLDP packet to egress the interface from the
PF_VSI is being based on the SKB's priority field.
It checks to see if the packets priority is equal to
TC_PRIO_CONTROL. Injected LLDP packets do not always
meet this condition.
SCAPY defaults to a sk_buff->protocol value of ETH_P_ALL
(0x0003) and does not set the priority field. There will
be other injection methods (even ones used by end users)
that will not correctly configure the socket so that
SKB fields are correctly populated.
Then ethernet header has to have to correct value for
the protocol though.
Add a check to also allow packets whose ethhdr->h_proto
matches ETH_P_LLDP (0x88CC).
Fixes: 0c3a6101ff ("ice: Allow egress control packets from PF_VSI")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ethtool incorrectly reported supported and advertised auto-negotiation
settings for a backplane PHY image which did not support auto-negotiation.
This can occur when using media or PHY type for reporting ethtool
supported and advertised auto-negotiation settings.
Remove setting supported and advertised auto-negotiation settings based
on PHY type in ice_phy_type_to_ethtool(), and MAC type in
ice_get_link_ksettings().
Ethtool supported and advertised auto-negotiation settings should be
based on the PHY image using the AQ command get PHY capabilities with
media. Add setting supported and advertised auto-negotiation settings
based get PHY capabilities with media in ice_get_link_ksettings().
Fixes: 48cb27f2fd ("ice: Implement handlers for ethtool PHY/link operations")
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
VSI rebuild can be failed for LAN queue config, then the VF's VSI will
be NULL, the VF reset should be stopped with the VF entering into the
disable state.
Fixes: 12bb018c53 ("ice: Refactor VF reset")
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Some AVF drivers expect the VF_MBX_ATQLEN register to be cleared for any
type of VFR/VFLR. Fix this by clearing the VF_MBX_ATQLEN register at the
same time as VF_MBX_ARQLEN.
Fixes: 82ba01282c ("ice: clear VF ARQLEN register on reset")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 12bb018c53 ("ice: Refactor VF reset") caused a regression
that removes the ability for a VF to request a different amount of
queues via VIRTCHNL_OP_REQUEST_QUEUES. This prevents VF drivers to
either increase or decrease the number of queue pairs they are
allocated. Fix this by using the variable vf->num_req_qs when
determining the vf->num_vf_qs during VF VSI creation.
Fixes: 12bb018c53 ("ice: Refactor VF reset")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit c7a219048e ("ice: Remove xsk_buff_pool from VSI structure")
silently introduced a regression and broke the Tx side of AF_XDP in copy
mode. xsk_pool on ice_ring is set only based on the existence of the XDP
prog on the VSI which in turn picks ice_clean_tx_irq_zc to be executed.
That is not something that should happen for copy mode as it should use
the regular data path ice_clean_tx_irq.
This results in a following splat when xdpsock is run in txonly or l2fwd
scenarios in copy mode:
<snip>
[ 106.050195] BUG: kernel NULL pointer dereference, address: 0000000000000030
[ 106.057269] #PF: supervisor read access in kernel mode
[ 106.062493] #PF: error_code(0x0000) - not-present page
[ 106.067709] PGD 0 P4D 0
[ 106.070293] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 106.074721] CPU: 61 PID: 0 Comm: swapper/61 Not tainted 5.12.0-rc2+ #45
[ 106.081436] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019
[ 106.092027] RIP: 0010:xp_raw_get_dma+0x36/0x50
[ 106.096551] Code: 74 14 48 b8 ff ff ff ff ff ff 00 00 48 21 f0 48 c1 ee 30 48 01 c6 48 8b 87 90 00 00 00 48 89 f2 81 e6 ff 0f 00 00 48 c1 ea 0c <48> 8b 04 d0 48 83 e0 fe 48 01 f0 c3 66 66 2e 0f 1f 84 00 00 00 00
[ 106.115588] RSP: 0018:ffffc9000d694e50 EFLAGS: 00010206
[ 106.120893] RAX: 0000000000000000 RBX: ffff88984b8c8a00 RCX: ffff889852581800
[ 106.128137] RDX: 0000000000000006 RSI: 0000000000000000 RDI: ffff88984cd8b800
[ 106.135383] RBP: ffff888123b50001 R08: ffff889896800000 R09: 0000000000000800
[ 106.142628] R10: 0000000000000000 R11: ffffffff826060c0 R12: 00000000000000ff
[ 106.149872] R13: 0000000000000000 R14: 0000000000000040 R15: ffff888123b50018
[ 106.157117] FS: 0000000000000000(0000) GS:ffff8897e0f40000(0000) knlGS:0000000000000000
[ 106.165332] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 106.171163] CR2: 0000000000000030 CR3: 000000000560a004 CR4: 00000000007706e0
[ 106.178408] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 106.185653] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 106.192898] PKRU: 55555554
[ 106.195653] Call Trace:
[ 106.198143] <IRQ>
[ 106.200196] ice_clean_tx_irq_zc+0x183/0x2a0 [ice]
[ 106.205087] ice_napi_poll+0x3e/0x590 [ice]
[ 106.209356] __napi_poll+0x2a/0x160
[ 106.212911] net_rx_action+0xd6/0x200
[ 106.216634] __do_softirq+0xbf/0x29b
[ 106.220274] irq_exit_rcu+0x88/0xc0
[ 106.223819] common_interrupt+0x7b/0xa0
[ 106.227719] </IRQ>
[ 106.229857] asm_common_interrupt+0x1e/0x40
</snip>
Fix this by introducing the bitmap of queues that are zero-copy enabled,
where each bit, corresponding to a queue id that xsk pool is being
configured on, will be set/cleared within ice_xsk_pool_{en,dis}able and
checked within ice_xsk_pool(). The latter is a function used for
deciding which napi poll routine is executed.
Idea is being taken from our other drivers such as i40e and ixgbe.
Fixes: c7a219048e ("ice: Remove xsk_buff_pool from VSI structure")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.
Fixes: efc2214b60 ("ice: Add support for XDP")
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Register ice client auxiliary RDMA device on the auxiliary bus per
PCIe device function for the auxiliary driver (irdma) to attach to.
It allows to realize a single RDMA driver (irdma) capable of working with
multiple netdev drivers over multi-generation Intel HW supporting RDMA.
There is no load ordering dependencies between ice and irdma.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add implementations for supporting iidc operations for device operation
such as allocation of resources and event notifications.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Probe the device's capabilities to see if it supports RDMA. If so, allocate
and reserve resources to support its operation; populate structures with
initial values.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, RSS hash input is not available to AVF by ethtool, it is set
by the PF directly.
Add the RSS configure support for AVF through new virtchnl message, and
define the capability flag VIRTCHNL_VF_OFFLOAD_ADV_RSS_PF to query this
new RSS offload support.
Signed-off-by: Jia Guo <jia.guo@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Bo Chen <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the driver gets the VF's VSI by using a long string of
dereferences (i.e. vf->pf->vsi[vf->lan_vsi_idx]). If the method to get
the VF's VSI were to change the driver would have to change it in every
location. Fix this by adding the helper ice_get_vf_vsi().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Pointer vsi is being re-assigned a value that is never read,
the assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As the hardware is capable of supporting UDP segmentation offload, add a
capability bit to virtchnl.h to communicate this and have the driver
advertise its support.
Suggested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Declare bitmap of allowed commands on VF. Initialize default
opcodes list that should be always supported. Declare array of
supported opcodes for each caps used in virtchnl code.
Change allowed bitmap by setting or clearing corresponding
bit to allowlist (bit set) or denylist (bit clear).
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Attempt to detect malicious VFs and, if suspected, log the information but
keep going to allow the user to take any desired actions.
Potentially malicious VFs are identified by checking if the VFs are
transmitting too many messages via the PF-VF mailbox which could cause an
overflow of this channel resulting in denial of service. This is done by
creating a snapshot or static capture of the mailbox buffer which can be
traversed and in which the messages sent by VFs are tracked.
Co-developed-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Signed-off-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Co-developed-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The scope of this variable can be reduced so do that.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We were saving the return value from ice_vsi_manage_rss_lut(), but
the errors from that function are not critical so change it to
return void and remove the code that saved the value.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Silence false errors, warnings and style issues reported by cppcheck.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the vsi->vf_id is set only for ICE_VSI_VF and it's left as 0
for all other VSI types. This is confusing and could be problematic
since 0 is a valid vf_id. Fix this by always setting non VF VSI types to
ICE_INVAL_VFID.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The only time you can ever have a rq_last_status is if
a firmware event was somehow reporting a status on the receive
queue, which are generally firmware initiated events or
mailbox messages from a VF. Mostly this struct member was unused.
Fix this problem by still printing the value of the field in a debug
print, but don't store the value forever in a struct, potentially
creating opportunities for callers to use the wrong struct member.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Do a minor refactor on ice_vsi_rebuild to use a local
variable to store vsi->type.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver previously printed it's PCI address in
the name field for the pci resource, which when displayed
via /proc/iomem, would print the same thing twice.
It's more useful for debugging to see the driver name, as
most other modules do.
Here's a diff of before and after this change:
99100000-991fffff : 0000:3b:00.1
9a000000-a04fffff : PCI Bus 0000:3b
9a000000-9bffffff : 0000:3b:00.1
- 9a000000-9bffffff : 0000:3b:00.1
+ 9a000000-9bffffff : ice
9c000000-9dffffff : 0000:3b:00.0
- 9c000000-9dffffff : 0000:3b:00.0
+ 9c000000-9dffffff : ice
9e000000-9effffff : 0000:3b:00.1
9f000000-9fffffff : 0000:3b:00.0
a0000000-a000ffff : 0000:3b:00.1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There was an excessive increment of the QSFP page, which is
now fixed. Additionally, this new update now reads 8 bytes
at a time and will retry each request if the module/bus is
busy.
Also, prevent reading from upper pages if module does not
support those pages.
Signed-off-by: Scott W Taylor <scott.w.taylor@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use a dedicated bitfield in order to both increase
the amount of checking around the length of ITR writes
as well as simplify the checks of dynamic mode.
Basically unpack the "high bit means dynamic" logic
into bitfields.
Also, remove some unused ITR defines.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver would occasionally miss that there were outstanding
descriptors to clean when exiting busy/napi poll. This issue has
been in the code since the introduction of the ice driver.
Attempt to "catch" any remaining work by triggering a software
interrupt when exiting napi poll or busy-poll. This will not
cause extra interrupts in the case of normal execution.
This issue was found when running sfnt-pingpong, with busy
poll enabled, and typically with larger I/O sizes like > 8192,
the program would occasionally report > 1 second maximums
to complete a ping pong.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver has support for adaptive interrupt moderation, an
algorithm for tuning the interrupt rate dynamically. This algorithm
is based on various assumptions about ring size, socket buffer size,
link speed, SKB overhead, ethernet frame overhead and more.
The Linux kernel has support for a dynamic interrupt moderation
algorithm known as "dimlib". Replace the custom driver-specific
implementation of dynamic interrupt moderation with the kernel's
algorithm.
The Intel hardware has a different hardware implementation than the
originators of the dimlib code had to work with, which requires the
driver to use a slightly different set of inputs for the actual
moderation values, while getting all the advice from dimlib of
better/worse, shift left or right.
The change made for this implementation is to use a pair of values
for each of the 5 "slots" that the dimlib moderation expects, and
the driver will program those pairs when dimlib recommends a slot to
use. The currently implementation uses two tables, one for receive
and one for transmit, and the pairs of values in each slot set the
maximum delay of an interrupt and a maximum number of interrupts per
second (both expressed in microseconds).
There are two separate kinds of bugs fixed by using DIMLIB, one is
UDP single stream send was too slow, and the other is that 8K
ping-pong was going to the most aggressive moderation and has much
too high latency.
The overall result of using DIMLIB is that we meet or exceed our
performance expectations set based on the old algorithm.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Introduce several new helpers for writing ITR and GLINT_RATE
registers, and refactor the code calling them. This resulted
in removal of several duplicate functions and rolled a bunch
of simple code back into the calling routines.
In particular this removes some code that was doing both
a store and a set in a helper function, which seems better
done as separate tasks in the caller (and generally takes
less lines of code even with a tiny bit of repetition).
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add two new VSI states, one to track if a netdev for the VSI has been
allocated and the other to track if the netdev has been registered.
Call unregister_netdev/free_netdev only when the corresponding state
bits are set.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the leading underscores in enum ice_pf_state. This is not really
communicating anything and is unnecessary. No functional change.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The well-known IANA protocol port 3260 (iscsi-target 0x0cbc) and the
ether-types 0x8906 (ETH_P_FCOE) and 0x8914 (ETH_P_FIP) are already defined
in kernel header files. Use those definitions instead of open-coding the
same.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
A for-loop is using a u8 loop counter that is being compared to
a u32 cmp_dcbcfg->numapp to check for the end of the loop. If
cmp_dcbcfg->numapp is larger than 255 then the counter j will wrap
around to zero and hence an infinite loop occurs. Fix this by making
counter j the same type as cmp_dcbcfg->numapp.
Addresses-Coverity: ("Infinite loop")
Fixes: aeac8ce864 ("ice: Recognize 860 as iSCSI port in CEE mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ice_suspend(), ice_clear_interrupt_scheme() is called, and then
irq_free_descs() will be eventually called to free irq and its descriptor.
In ice_resume(), ice_init_interrupt_scheme() is called to allocate new
irqs. However, in ice_rebuild_arfs(), struct irq_glue and struct cpu_rmap
maybe cannot be freed, if the irqs that released in ice_suspend() were
reassigned to other devices, which makes irq descriptor's affinity_notify
lost.
So call ice_free_cpu_rx_rmap() before ice_clear_interrupt_scheme(), which
can make sure all irq_glue and cpu_rmap can be correctly released before
corresponding irq and descriptor are released.
Fix the following memory leak.
unreferenced object 0xffff95bd951afc00 (size 512):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
18 00 00 00 18 00 18 00 70 fc 1a 95 bd 95 ff ff ........p.......
00 00 ff ff 01 00 ff ff 02 00 ff ff 03 00 ff ff ................
backtrace:
[<0000000072e4b914>] __kmalloc+0x336/0x540
[<0000000054642a87>] alloc_cpu_rmap+0x3b/0xb0
[<00000000f220deec>] ice_set_cpu_rx_rmap+0x6a/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
unreferenced object 0xffff95bd81b0a2a0 (size 96):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
38 00 00 00 01 00 00 00 e0 ff ff ff 0f 00 00 00 8...............
b0 a2 b0 81 bd 95 ff ff b0 a2 b0 81 bd 95 ff ff ................
backtrace:
[<00000000582dd5c5>] kmem_cache_alloc_trace+0x31f/0x4c0
[<000000002659850d>] irq_cpu_rmap_add+0x25/0xe0
[<00000000495a3055>] ice_set_cpu_rx_rmap+0xb4/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Yongxin Liu <yongxin.liu@windriver.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Checkpatch reports the following, fix it.
-----------------------------------------
drivers/net/ethernet/intel/ice/ice_main.c
-----------------------------------------
CHECK:BRACES: Blank lines aren't necessary before a close brace '}'
FILE: drivers/net/ethernet/intel/ice/ice_main.c:455:
+
+}
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Currently the driver is doing two unnecessary checks. First both ops are
checking if the VLAN ID passed in is less than VLAN_N_VID and second
both ops are checking to see if a port VLAN is configured on the VSI.
The first check is already handled by the 8021q driver so this is an
unnecessary check. The second check is unnecessary because the PF VSI is
never put into a port VLAN.
Remove these checks.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tracking of the rx_gro_dropped statistic was removed in
commit f73fc40327 ("ice: drop dead code in ice_receive_skb()").
Remove the associated variables and its reporting to ethtool stats.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace multiple instances of vsi->back and pi->phy with equivalent
local variables
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In ice_init_phy_user_cfg, vsi is used only to get to hw. Remove this
and just use pi->hw
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Beyond a specific version of firmware, there is no need to provide
override values to the firmware when setting PHY capabilities. In this
case, we do not need to indicate whether we're in Strict or Lenient Link
Mode.
In the case of translating capabilities to the configuration structure,
the module compliance enforcement is already correctly set by firmware,
so the extra code block is redundant.
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Recent firmware supports a new "get PHY capabilities" mode
ICE_AQC_REPORT_DFLT_CFG which makes it unnecessary for the driver
to track and apply NVM based default link overrides.
If FW AQ API version supports it, use Report Default Configuration.
Add check function for Report Default Configuration support and update
accordingly.
Also change adv_phy_type_[lo|hi] to advert_phy_type[lo|hi] for
clarity.
Co-developed-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Signed-off-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In ice_set_link_ksettings, use assignment instead of memset/memcpy
where possible
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Return more appropriate error codes so that the right error
message is communicated to the user by ethtool.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In ice_set_link_ksettings, change 'abilities' to 'phy_caps' and 'p' to
'pi'. This is more consistent with similar usages elsewhere in the
driver.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The loop checking for PF VSI doesn't make any sense. The VSI type
backing the netdev passed to ice_set_link_ksettings will always be
of type ICE_PF_VSI. Remove it.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When link is owned by manageability, the driver is not allowed to fiddle
with link. FW returns ICE_AQ_RC_EMODE if the driver attempts to do so.
This patch adds a new function ice_set_link which abstracts the call to
ice_aq_set_link_restart_an and provides a clean way to turn on/off link.
While making this change, I also spotted that an int variable was being
used to hold both an ice_status return code and the Linux errno return
code. This pattern more often than not results in the driver inadvertently
returning ice_status back to kernel which is a major boo-boo. Clean it up.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
For get PHY abilities AQ, the specification defines "report modes"
as "with media", "without media" and "active configuration". For
clarity, rename macros to align with the specification.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the recursive way of adding the nodes to the layer in order
to reduce the stack usage. Instead the algorithm is modified to use
a while loop.
The previous code was scanning recursively the nodes horizontally.
The total stack consumption will be based on number of nodes present
on that layer. In some cases it can consume more stack.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Retry sending some AQ commands, as result of EBUSY AQ error.
ice_aqc_opc_get_link_topo
ice_aqc_opc_lldp_stop
ice_aqc_opc_lldp_start
ice_aqc_opc_lldp_filter_ctrl
This change follows the latest guidelines from HW team. It is
better to retry the same AQ command several times, as the result
of EBUSY, instead of returning error to the caller right away.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The following is reported by checkpatch, correct it.
-----------------------------------------------
drivers/net/ethernet/intel/ice/ice_adminq_cmd.h
-----------------------------------------------
WARNING:NETWORKING_BLOCK_COMMENT_STYLE: networking block comments don't use an empty /* line, use /* Comment...
FILE: drivers/net/ethernet/intel/ice/ice_adminq_cmd.h:1428:
+/*
+ * Send to PF command (indirect 0x0801) ID is only used by PF
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
A few style issues reported by checkpatch have snuck into the code; resolve
the style issues.
COMPLEX_MACRO: Macros with complex values should be enclosed in parentheses
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
struct ice_vsi has two fields, state and flags which seem to
be serving the same purpose. Consolidate them into one field
'state'.
enum ice_state is used to represent state information of the PF.
While some of these enum values can be use to represent VSI state,
it makes more sense to represent VSI state with its own enum. So
derive a new enum ice_vsi_state from ice_vsi_flags and ice_state
and use it. Also rename enum ice_state to ice_pf_state for clarity.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently ice_set/get_rss are used to set/get the RSS LUT and/or RSS
key. However nearly everywhere these functions are called only the LUT
or key are set/get. Also, making this change reduces how many things
ice_set/get_rss are doing. Fix this by adding ice_set/get_rss_lut and
ice_set/get_rss_key functions.
Also, consolidate all calls for setting/getting the RSS LUT and RSS Key
to use ice_set/get_rss_lut() and ice_set/get_rss_key().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Update ice_aq_get_rss_lut() and ice_aq_set_rss_lut() to take a new
structure ice_aq_get_set_rss_params instead of passing individual
parameters. This is done for 2 reasons:
1. Reduce the number of parameters passed to the functions.
2. Reduce the amount of change required if the arguments ever need to be
updated in the future.
Also, reduce duplicate code that was checking for an invalid vsi_handle
and lut parameter by moving the checks to the lower level
__ice_aq_get_set_rss_lut().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, ice_vsi_setup_q_map() depends on the VSI's rss_size. However,
the Rx Queue Mapping section of the VSI context has no dependency on RSS.
Instead, limit the maximum number of Rx queues per TC based on the Rx
Queue mapping section of the VSI context, which currently allows for up
to 256 Rx queues per TC.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Align all ptype bitmap to follow ice_ptypes_xxx prefix.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use *malloc() instead of *calloc() when allocating only a single object as
opposed to an array of objects.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Check for bail out condition before calling ice_aq_sff_eeprom
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit a012dca9f7 ("ice: add ethtool -m support for reading i2c eeprom
modules") unnecessarily added the ICE_AQ_FLAG_BUF flag to the descriptor
when sending the indirect Read/Write SFF EEPROM AQ command. The flag is
already added later in the code flow for all indirect AQ commands, i.e.
commands that provide an additional data buffer.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Change link misconfiguration message since the configuration
could be intended by the user.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is an issue when the Tx or Rx ring size increases using
'ethtool -L ...' where the new rings don't get the correct ITR
values because when we rebuild the VSI we don't know that some
of the rings may be new.
Fix this by looking at the original number of rings and
determining if the rings in ice_vsi_rebuild_set_coalesce()
were not present in the original rings received in
ice_vsi_rebuild_get_coalesce().
Also change the code to return an error if we can't allocate
memory for the coalesce data in ice_vsi_rebuild().
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There are two package versions in the package binary. Today, these two
version numbers are the same. However, in the future that may change.
Update code to use the package info from the ice segment metadata
section, which is the package information that is actually downloaded to
the firmware during the download package process.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Once a netdev is registered, the corresponding network interface can
be immediately used by userspace utilities (like say NetworkManager).
This can be problematic if the driver technically isn't fully up yet.
Move netdev registration to the end of probe, as by this time the
driver data structures and device will be initialized as expected.
However, delaying netdev registration causes a failure in the aRFS flow
where netdev->reg_state == NETREG_REGISTERED condition is checked. It's
not clear why this check was added to begin with, so remove it.
Local testing didn't indicate any issues with this change.
The state bit check in ice_open was put in as a stop-gap measure to
prevent a premature interface up operation. This is no longer needed,
so remove it.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Enable and configure XPS. The driver code implemented sets up the Transmit
Packet Steering Map, which in turn will be used by the kernel in queue
selection during Tx.
Signed-off-by: Benita Bose <benita.bose@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When ice_remove_vsi_lkup_fltr is called, by calling
ice_add_to_vsi_fltr_list local copy of vsi filter list
is created. If any issues during creation of vsi filter
list occurs it up for the caller to free already
allocated memory. This patch ensures proper memory
deallocation in these cases.
Fixes: 80d144c9ac ("ice: Refactor switch rule management structures and functions")
Signed-off-by: Robert Malz <robertx.malz@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As per the spec, the WoL control word read from the NVM should be
interpreted as port numbers, and not PF numbers. So when checking
if WoL supported, use the port number instead of the PF ID.
Also, ice_is_wol_supported doesn't really need a pointer to the pf
struct, but just needs a pointer to the hw instance.
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add handling of allocation fault for ice_vsi_list_map_info.
Also *fi should not be NULL pointer, it is a reference to raw
data field, so remove this variable and use the reference
directly.
Fixes: 9daf8208dd ("ice: Add support for switch filter programming")
Signed-off-by: Jacek Bułatek <jacekx.bulatek@intel.com>
Co-developed-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The original purpose of the ICE_DCBNL_DEVRESET was to protect
the driver during DCBNL device resets. But, the flow for
DCBNL device resets now consists of only calls up the stack
such as dev_close() and dev_open() that will result in NDO calls
to the driver. These will be handled with state changes from the
stack. Also, there is a problem of the dev_close and dev_open
being blocked by checks for reset in progress also using the
ICE_DCBNL_DEVRESET bit.
Since the ICE_DCBNL_DEVRESET bit is not necessary for protecting
the driver from DCBNL device resets and it is actually blocking
changes coming from the DCBNL interface, remove the bit from the
PF state and don't block driver function based on DCBNL reset in
progress.
Fixes: b94b013eb6 ("ice: Implement DCBNL support")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the order of number of array members and member size parameters in a
*calloc() call.
Fixes: b3c3890489 ("ice: avoid unnecessary single-member variable-length structs")
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a possibility of race between ice_open or ice_stop calls
performed by OS and reset handling routine both trying to modify VSI
resources. Observed scenarios:
- reset handler deallocates memory in ice_vsi_free_arrays and ice_open
tries to access it in ice_vsi_cfg_txq leading to driver crash
- reset handler deallocates memory in ice_vsi_free_arrays and ice_close
tries to access it in ice_down leading to driver crash
- reset handler clears port scheduler topology and sets port state to
ICE_SCHED_PORT_STATE_INIT leading to ice_ena_vsi_txq fail in ice_open
To prevent this additional checks in ice_open and ice_stop are
introduced to make sure that OS is not allowed to alter VSI config while
reset is in progress.
Fixes: cdedef59de ("ice: Configure VSIs for Tx/Rx")
Signed-off-by: Krzysztof Goreczny <krzysztof.goreczny@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
iSCSI can use both TCP ports 860 and 3260. However, in our current
implementation, the ice_aqc_opc_get_cee_dcb_cfg (0x0A07) AQ command
doesn't provide a way to communicate the protocol port number to the
AQ's caller. Thus, we assume that 3260 is the iSCSI port number at the
AQ's caller layer.
Rely on the dcbx-willing mode, desired QoS and remote QoS configuration to
determine which port number that iSCSI will use.
Fixes: 0ebd3ff13c ("ice: Add code for DCB initialization part 2/4")
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
250 msec timeout is insufficient for some AQ commands. Advice from FW
team was to increase the timeout. Increase to 1 second.
Fixes: 7ec59eeac8 ("ice: Add support for control queues")
Signed-off-by: Fabio Pricoco <fabio.pricoco@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
An incorrect NVM update procedure can result in the driver failing probe.
In this case, the recommended resolution method is to update the NVM
using the right procedure. However, if the driver fails probe, the user
will not be able to update the NVM. So do not fail probe on link/PHY
errors.
Fixes: 1a3571b593 ("ice: restore PHY settings on media insertion")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-03-24
The following pull-request contains BPF updates for your *net-next* tree.
We've added 37 non-merge commits during the last 15 day(s) which contain
a total of 65 files changed, 3200 insertions(+), 738 deletions(-).
The main changes are:
1) Static linking of multiple BPF ELF files, from Andrii.
2) Move drop error path to devmap for XDP_REDIRECT, from Lorenzo.
3) Spelling fixes from various folks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of just letting the code
fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Correct reported warnings for "warning: expecting prototype for ...
Prototype was for ... instead"
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Enable returning FDIR completion status by checking the
ctrl_vsi Rx queue descriptor value.
To enable returning FDIR completion status from ctrl_vsi Rx queue,
COMP_Queue and COMP_Report of FDIR filter programming descriptor
needs to be properly configured. After program request sent to ctrl_vsi
Tx queue, ctrl_vsi Rx queue interrupt will be triggered and
completion status will be returned.
Driver will first issue request in ice_vc_fdir_add_fltr(), then
pass FDIR context to the background task in interrupt service routine
ice_vc_fdir_irq_handler() and finally deal with them in
ice_flush_fdir_ctx(). ice_flush_fdir_ctx() will check the descriptor's
value, fdir context, and then send back virtual channel message to VF
by calling ice_vc_add_fdir_fltr_post(). An additional timer will be
setup in case of hardware interrupt timeout.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add new FDIR filter type to forward GTPU packets by matching TEID or QFI.
The filter is only enabled when COMMS DDP package is downloaded.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add new filter type that allow forward non-IP Ethernet packets base on its
ethertype. The filter is only enabled when COMMS DDP package is loaded.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add two new actions support for VF FDIR:
A passthrough action does not specify the destination queue, but
just allow the packet go to next pipeline stage, a typical use
cases is combined with a software mark (FDID) action.
Allow specify a 2^n continuous queues as the destination of a FDIR rule.
Packet distribution is based on current RSS configure.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add basic FDIR flow list and pattern / action parse functions for VF.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The virtual channel is going to be extended to support FDIR and
RSS configure from AVF. New data structures and OP codes will be
added, the patch enable the FDIR part.
To support above advanced AVF feature, we need to figure out
what kind of data structure should be passed from VF to PF to describe
an FDIR rule or RSS config rule. The common part of the requirement is
we need a data structure to represent the input set selection of a rule's
hash key.
An input set selection is a group of fields be selected from one or more
network protocol layers that could be identified as a specific flow.
For example, select dst IP address from an IPv4 header combined with
dst port from the TCP header as the input set for an IPv4/TCP flow.
The patch adds a new data structure virtchnl_proto_hdrs to abstract
a network protocol headers group which is composed of layers of network
protocol header(virtchnl_proto_hdr).
A protocol header contains a 32 bits mask (field_selector) to describe
which fields are selected as input sets, as well as a header type
(enum virtchnl_proto_hdr_type). Each bit is mapped to a field in
enum virtchnl_proto_hdr_field guided by its header type.
+------------+-----------+------------------------------+
| | Proto Hdr | Header Type A |
| | +------------------------------+
| | | BIT 31 | ... | BIT 1 | BIT 0 |
| |-----------+------------------------------+
|Proto Hdrs | Proto Hdr | Header Type B |
| | +------------------------------+
| | | BIT 31 | ... | BIT 1 | BIT 0 |
| |-----------+------------------------------+
| | Proto Hdr | Header Type C |
| | +------------------------------+
| | | BIT 31 | ... | BIT 1 | BIT 0 |
| |-----------+------------------------------+
| | .... |
+-------------------------------------------------------+
All fields in enum virtchnl_proto_hdr_fields are grouped with header type
and the value of the first field of a header type is always 32 aligned.
enum proto_hdr_type {
header_type_A = 0;
header_type_B = 1;
....
}
enum proto_hdr_field {
/* header type A */
header_A_field_0 = 0,
header_A_field_1 = 1,
header_A_field_2 = 2,
header_A_field_3 = 3,
/* header type B */
header_B_field_0 = 32, // = header_type_B << 5
header_B_field_0 = 33,
header_B_field_0 = 34
header_B_field_0 = 35,
....
};
So we have:
proto_hdr_type = proto_hdr_field / 32
bit offset = proto_hdr_field % 32
To simply the protocol header's operations, couple help macros are added.
For example, to select src IP and dst port as input set for an IPv4/UDP
flow.
we have:
struct virtchnl_proto_hdr hdr[2];
VIRTCHNL_SET_PROTO_HDR_TYPE(&hdr[0], IPV4)
VIRTCHNL_ADD_PROTO_HDR_FIELD(&hdr[0], IPV4, SRC)
VIRTCHNL_SET_PROTO_HDR_TYPE(&hdr[1], UDP)
VIRTCHNL_ADD_PROTO_HDR_FIELD(&hdr[1], UDP, DST)
The byte array is used to store the protocol header of a training package.
The byte array must be network order.
The patch added virtual channel support for iAVF FDIR add/validate/delete
filter. iAVF FDIR is Flow Director for Intel Adaptive Virtual Function
which can direct Ethernet packets to the queues of the Network Interface
Card. Add/delete command is adding or deleting one rule for each virtual
channel message, while validate command is just verifying if this rule
is valid without any other operations.
To add or delete one rule, driver needs to config TCAM and Profile,
build training packets which contains the input set value, and send
the training packets through FDIR Tx queue. In addition, driver needs to
manage the software context to avoid adding duplicated rules, deleting
non-existent rule, input set conflicts and other invalid cases.
NOTE:
Supported pattern/actions and their parse functions are not be included in
this patch, they will be added in a separate one.
Signed-off-by: Jeff Guo <jia.guo@intel.com>
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Simei Su <simei.su@intel.com>
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We are going to enable FDIR configure for AVF through virtual channel.
The first step is to add helper functions to support control VSI setup.
A control VSI will be allocated for a VF when AVF creates its
first FDIR rule through ice_vf_ctrl_vsi_setup().
The patch will also allocate FDIR rule space for VF's control VSI.
If a VF asks for flow director rules, then those should come entirely
from the best effort pool and not from the guaranteed pool. The patch
allow a VF VSI to have only space in the best effort rules.
Signed-off-by: Xiaoyun Li <xiaoyun.li@intel.com>
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Separate IPv4 and IPv6 ptype bit mask table into 2 tables:
with or without L4 protocols.
When a flow filter without any l4 type is specified, the
ICE_FLOW_SEG_HDR_IPV_OTHER flag can be used to describe if user
want to create a IP rule target for all IP packet or just IP
packet without l4 header.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
To apply different input set for GTP-U packet with or without extend
header as well as GTP-U uplink and downlink, we need to add TCAM mask
matching capability. This allows comprehending different PTYPE
attributes by examining flags from the parser. Using this method,
different profiles can be used by examining flag values from the parser.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add more protocol support in flow filter, these
include PPPoE, L2TPv3, GTP, PFCP, ESP and AH.
Signed-off-by: Ting Xu <ting.xu@intel.com>
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
To support FDIR input set with protocol field like DSCP, TTL,
PROT, etc. which is not word aligned, we need to enable field
vector masking.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add more protocol and field support for flow filter include:
ETH, VLAN, ICMP, ARP and TCP flag.
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We want to change the current ndo_xdp_xmit drop semantics because it will
allow us to implement better queue overflow handling. This is working
towards the larger goal of a XDP TX queue-hook. Move XDP_REDIRECT error
path handling from each XDP ethernet driver to devmap code. According to
the new APIs, the driver running the ndo_xdp_xmit pointer, will break tx
loop whenever the hw reports a tx error and it will just return to devmap
caller the number of successfully transmitted frames. It will be devmap
responsibility to free dropped frames.
Move each XDP ndo_xdp_xmit capable driver to the new APIs:
- veth
- virtio-net
- mvneta
- mvpp2
- socionext
- amazon ena
- bnxt
- freescale (dpaa2, dpaa)
- xen-frontend
- qede
- ice
- igb
- ixgbe
- i40e
- mlx5
- ti (cpsw, cpsw-new)
- tun
- sfc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/bpf/ed670de24f951cfd77590decf0229a0ad7fd12f6.1615201152.git.lorenzo@kernel.org
Update the Intel drivers to make use of ethtool_sprintf. The general idea
is to reduce code size and overhead by replacing the repeated pattern of
string printf statements and ETH_STRING_LEN counter increments.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize ice_run_xdp_zc() for the XDP program verdict being
XDP_REDIRECT in the xsk zero-copy path. This path is only used when
having AF_XDP zero-copy on and in that case most packets will be
directed to user space. This provides a little over 100k extra packets
in throughput on my server when running l2fwd in xdpsock.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice_rx_offset(), that is supposed to initialize the Rx buffer headroom,
relies on ICE_RX_FLAGS_RING_BUILD_SKB flag as well as XDP prog presence.
Currently, the callsite of mentioned function is placed incorrectly
within ice_setup_rx_ring() where Rx ring's build skb flag is not
set yet. This causes the XDP_REDIRECT to be partially broken due to
inability to create xdp_frame in the headroom space, as the headroom is
0.
Fix this by moving ice_rx_offset() to ice_setup_rx_ctx() after the flag
setting.
Fixes: f1b1f409bf ("ice: store the result of ice_rx_offset() onto ice_ring")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the wrong napi work done reporting in the xsk path of the ice
driver. The code in the main Rx processing loop was written to assume
that the buffer allocation code returns true if all allocations where
successful and false if not. In contrast with all other Intel NIC xsk
drivers, the ice_alloc_rx_bufs_zc() has the inverted logic messing up
the work done reporting in the napi loop.
This can be fixed either by inverting the return value from
ice_alloc_rx_bufs_zc() in the function that uses this in an incorrect
way, or by changing the return value of ice_alloc_rx_bufs_zc(). We
chose the latter as it makes all the xsk allocation functions for
Intel NICs behave in the same way. My guess is that it was this
unexpected discrepancy that gave rise to this bug in the first place.
Fixes: 5bb0c4b5eb ("ice, xsk: Move Rx allocation out of while-loop")
Reported-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It was possible to have Rx queues that were not available for use
by RSS. This would happen when increasing the number of Rx queues
while there was a user defined RSS LUT.
Always update the number of available RSS queues when changing the
number of Rx queues.
Fixes: 87324e747f ("ice: Implement ethtool ops for channels")
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
DCBX_CAP bits were not being adjusted when switching
between SW and FW controlled LLDP.
Adjust bits to correctly indicate which mode the
LLDP logic is in.
Fixes: b94b013eb6 ("ice: Implement DCBNL support")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently if an AVF driver doesn't account for the possibility of a
port VLAN when determining its max packet size then packets at MTU will
be dropped. It is not the VF driver's responsibility to account for a
port VLAN so fix this. To fix this, do the following:
1. Add a function that determines the max packet size a VF is allowed by
using the port's max packet size and whether the VF is in a port
VLAN. If a port VLAN is configured then a VF's max packet size will
always be the port's max packet size minus VLAN_HLEN. Otherwise it
will be the port's max packet size.
2. Use this function to verify the max packet size from the VF.
3. If there is a port VLAN configured then add 4 bytes (VLAN_HLEN) to
the VF's max packet size configuration.
Also, the VIRTCHNL_OP_GET_VF_RESOURCES message provides the capability
to communicate a VF's max packet size. Use the new function for this
purpose.
Fixes: 1071a8358a ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the PF will only set a trusted VF as the default VSI when it
requests FLAG_VF_UNICAST_PROMISC over VIRTCHNL. However, when
FLAG_VF_MULTICAST_PROMISC is set it's expected that the trusted VF will
see multicast packets that don't have a matching destination MAC in the
devices internal switch. Fix this by setting the trusted VF as the
default VSI if either FLAG_VF_UNICAST_PROMISC or
FLAG_VF_MULTICAST_PROMISC is set.
Fixes: 01b5e89aab ("ice: Add VF promiscuous support")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In the driver currently, we are reporting max number of TCs
to the DCBNL callback as a kernel define set to 8. This is
preventing userspace applications performing DCBx to correctly
down map the TCs from requested to actual values.
Report the actual max TC value to userspace from the capability
struct.
Fixes: b94b013eb6 ("ice: Implement DCBNL support")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Output of ice_rx_offset() is based on ethtool's priv flag setting, which
when changed, causes PF reset (disables napi, frees irqs, loads
different Rx mem model, etc.). This means that within napi its result is
constant and there is no reason to call it per each processed frame.
Add new 'rx_offset' field to ice_ring that is meant to hold the
ice_rx_offset() result and use it within ice_clean_rx_irq().
Furthermore, use it within ice_alloc_mapped_page().
Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Whole zero-copy variant of clean Rx IRQ is executed when xsk_pool is
attached to rx_ring and it can happen only when XDP program is present
on interface. Therefore it is safe to assume that program is always
!NULL and there is no need for checking it in ice_run_xdp_zc.
Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
dev_validate_mtu checks that mtu value specified by user is not less
than min mtu and not greater than max allowed mtu. It is being done
before calling the ndo_change_mtu exposed by driver, so remove these
redundant checks in ice_change_mtu.
Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Similar thing has been done in i40e, as there is no real need for having
the sk_buff pointer in each rx_buf. Non-eop frames can be simply handled
on that pointer moved upwards to rx_ring.
Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There's no need for 'result' variable, we can directly return the
internal status based on action returned by xdp prog.
Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently if the driver is unable to get all the MSI-X vectors it wants, it
falls back to the minimum configuration which equates to a single Tx/Rx
traffic queue pair. Instead of using the minimum configuration, if given
more vectors than the minimum, utilize those vectors for additional traffic
queues after accounting for other interrupts.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
This message indicates an error on close, not open.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Casting a void * rvalue in an assignment is unnecessary in C; remove the
casts.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor the DCB related variables out of the ice_port_info_struct. The
goal is to make the ice_port_info struct cleaner.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Co-developed-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The writeback enable logic was incorrectly implemented (due to
misunderstanding what the side effects of the implementation would be
during polling).
Fix this logic issue, while implementing a new feature allowing the user
to control the writeback frequency using the knobs for controlling
interrupt throttling that we already have. Basically if you leave
adaptive interrupts enabled, the writeback frequency will be varied even
if busy_polling or if napi-poll is in use. If the interrupt rates are
set to a fixed value by ethtool -C and adaptive is off, the driver will
allow the user-set interrupt rate to guide how frequently the hardware
will complete descriptors to the driver.
Effectively the user will get a control over the hardware efficiency,
allowing the choice between immediate interrupts or delayed up to a
maximum of the interrupt rate, even when interrupts are disabled
during polling.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The core clock frequency is currently hardcoded at 446 MHz for the RL
profile calculations. This causes issues since not all devices use that
clock frequency. Read the GLGEN_CLKSTAT_SRC register to determine which PSM
clock frequency is selected. This ensures that the rate limiter profile
calculations will be correct.
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Create set scheduler aggregator node and move for VSIs into respective
scheduler node. Max children per aggregator node is 64.
There are two types of aggregator node(s) created.
1. dedicated node for PF and _CTRL VSIs
2. dedicated node(s) for VFs.
As part of reset and rebuild, aggregator nodes are recreated and VSIs
are moved to respective aggregator node.
Having related VSIs in respective tree avoid starvation between PF and VF
w.r.t Tx bandwidth.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Co-developed-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Victor Raj <victor.raj@intel.com>
Co-developed-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the framework and initial implementation for receiving and processing
netdev bonding events. This is only the software support and the
implementation of the HW offload for bonding support will be coming at a
later time. There are some architectural gaps that need to be closed
before that happens.
Because this is a software only solution that supports in kernel bonding,
SR-IOV is not supported with this implementation.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Current implementation of netdev already contains xsk_buff_pools.
We no longer have to contain these structures in ice_vsi.
Refactor the code to operate on netdev-provided xsk_buff_pools.
Move scheduling napi on each queue to a separate function to
simplify setup function.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is an issue with some NVMs where an already existent LLDP
filter is blocking the creation of a filter to allow LLDP packets
to be redirected to the default VSI for the interface. This is
blocking all LLDP functionality based in the kernel when the FW
LLDP agent is disabled (e.g. software based DCBx).
Implement the new AQ command to allow adding VSI destinations to
existent filters on NVM versions that support the new command.
The new lldp_fltr_ctrl AQ command supports Rx filters only, so the
code flow for adding filters to disable Tx of control frames will
remain intact.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently there is no message printed on the host when a VF goes in and
out of promiscuous mode. This is causing confusion because this is the
expected behavior based on i40e. Fix this.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The check for a NULL pf pointer is moot since the earlier declaration and
assignment of struct device *dev already de-referenced the pointer. Also,
the only caller of ice_set_dflt_mib() already ensures pf is not NULL.
Cc: Dave Ertman <david.m.ertman@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the flex_array_size() helper with the recently added flexible array
members in structures.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
Refactor the code according to the use of a flexible-array member in
struct ice_res_tracker, instead of a one-element array and use the
struct_size() helper to calculate the size for the allocations.
Also, notice that the code below suggests that, currently, two too many
bytes are being allocated with devm_kzalloc(), as the total number of
entries (pf->irq_tracker->num_entries) for pf->irq_tracker->list[] is
_vectors_ and sizeof(*pf->irq_tracker) also includes the size of the
one-element array _list_ in struct ice_res_tracker.
drivers/net/ethernet/intel/ice/ice_main.c:3511:
3511 /* populate SW interrupts pool with number of OS granted IRQs. */
3512 pf->num_avail_sw_msix = (u16)vectors;
3513 pf->irq_tracker->num_entries = (u16)vectors;
3514 pf->irq_tracker->end = pf->irq_tracker->num_entries;
With this change, the right amount of dynamic memory is now allocated
because, contrary to one-element arrays which occupy at least as much
space as a single object of the type, flexible-array members don't
occupy such space in the containing structure.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.9-rc1/process/deprecated.html#zero-length-and-one-element-arrays
Built-tested-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Just as we recently added support for other stored firmware flash
versions, support display of the stored UNDI Option ROM version via
devlink info.
To do this, we need to introduce a new ice_get_inactive_orom_ver
function. This is a little trickier than with other flash versions. The
Option ROM version data was being read from a special "Boot
Configuration" block of the NVM Preserved Field Area. This block only
contains the *active* Option ROM version data. It is populated when the
device firmware finishes updating the Option ROM.
This method is ineffective at reading the stored Option ROM version
data. Instead of reading from this section of the flash, replace this
version extraction with one which locates the Combo Version information
from within the Option ROM binary.
This data is stored within the Option ROM at a 512 byte offset, in
a simple structured format. The structure uses a simple modulo 256
checksum for integrity verification. Scan through the Option ROM to
locate the CIVD data section, and extract the Combo Version.
Refactor ice_get_orom_ver_info so that it takes the bank select
enumeration parameter. Use this to implement ice_get_inactive_orom_ver.
Although all ice devices have a Boot Configuration block in the NVM PFA,
not all devices have a valid Option ROM. In this case, the old
ice_get_orom_ver_info would "succeed" but report a version of all
zeros. The new implementation would fail to locate the $CIV section in
the Option ROM and report an error. Thus, we must ensure that
ice_init_nvm does not fail if ice_get_orom_ver_info fails.
Use the new ice_get_inactive_orom_ver to allow reporting the Option ROM
versions for a pending update via devlink info.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a function to read the inactive netlist bank for version
information. To support this, refactor how we read the netlist version
data. Instead of using the firmware AQ interface with a module ID, read
from the flash as a flat NVM, using ice_read_flash_module.
This change requires a slight adjustment to the offset values used, as
reading from the flat NVM includes the type field (which was stripped by
firmware previously). Cleanup the macro names and move them to
ice_type.h. For clarity in how we calculate the offsets and so that
programmers can easily map the offset value to the data sheet, use
a wrapper macro to account for the offset adjustments.
Use the newly added ice_get_inactive_netlist_ver function to extract the
version data from the pending netlist module update. Add the stored
variants of "fw.netlist", and "fw.netlist.build" to the info version map
array.
With this change, we now report the "fw.netlist" and "fw.netlist.build"
versions into the stored section of the devlink info report. As with the
main NVM module versions, if there is no pending update, we report the
currently active values as stored.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The devlink info interface supports drivers reporting "stored" versions.
These versions indicate the version of an update that has been
downloaded to the device, but is not yet active.
The code for extracting the NVM version recently changed to enable
support for reading from either the active or the inactive bank. Use
this to implement ice_get_inactive_nvm_ver, which will read the NVM
version data from the inactive section of flash.
When reporting the versions via devlink info, first read the device
capabilities. Determine if there is a pending flash update, and if so,
extract relevant version information from the inactive flash. Store
these within the info context structure.
When reporting "stored" firmware versions, devlink documentation
indicates that we ought to always report a stored value, even if there
is no pending update. In this common case, the stored version should
match the running version. This means that each stored version should by
default fallback to the same value as reported by the running handler.
To support this, modify the version structure to have both a "getter"
and a "fallback". Modify the control loop so that it will use the
"fallback" function if the "getter" function does not report a version.
To report versions for which we can read the stored value, use a new
"stored()" macro. This macro will insert two entries into the version
list. The first entry is the traditional running version. The second is
the stored version, implemented with a fallback to the active version.
This is a little tricky, but reduces the overall duplication of elements
in the entry list, and ensures that running and stored values remain
consistent.
To avoid some duplication, add a combined() macro that will insert both
the running and stored versions into the version entry list.
Using this new support, add pending version reporter functions for
"fw.psid.api" and "fw.bundle_id". This enables reporting the stored
values for some of versions in the NVM module of the flash.
Reporting management versions is not implemented by this patch. The
active management version is reported to the driver via the AdminQ
mailbox during load. Although the version must be in the firmware binary
somewhere, accessing this from the inactive firmware is not trivial and
has not been implemented in this change.
Future changes will introduce support for reading the UNDI Option ROM
version and the version associated with the Netlist module.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When reading from the flash memory of the device, the ice driver has two
interfaces available to it. First, it can use a mediated interface via
firmware that allows specifying a module ID. This allows reading from
specific modules of the active flash bank.
The second interface available is to perform flat reads. This allows
complete access to the entire flash. However, using it requires the
software to handle calculating module location and interpret pointer
addresses.
While most data required is accessible through the convenient first
interface, certain flash contents are not. This includes the CSS header
information associated with the Option ROM and NVM banks, as well as any
access to the "inactive" banks used as scratch space for performing
flash updates.
In order to access all of the relevant flash contents, software must use
the flat reads. Rather than forcing all flows to perform flat read
calculations, introduce a new abstraction for reading from the flash:
ice_read_flash_module. This function provides an abstraction for reading
from either the active or inactive flash bank at the requested module.
This interface is very similar to the abstraction provided via firmware,
but allows access to additional modules, as well as providing
a mechanism to request access to both flash banks.
At first glance, it might make sense for this abstraction to allow
specifying precisely which bank (1st or 2nd) the caller wishes to read.
This is simpler to implement but more difficult to use. In practice,
most callers only know whether they want the active bank, or the
inactive bank. Rather than force callers to determine for themselves
which bank to read from, implement ice_read_flash_module in terms of
"active" vs "inactive". This significantly simplifies the implementation
at the caller level and is a more useful abstraction over the flash
contents.
Make use of this new interface to refactor reading of the main NVM
version information. Instead of using the firmware's mediated ShadowRAM
function, use the ice_read_flash_module abstraction.
To do this, notice that most reads of the NVM are going to be in 2-byte
word chunks. To simplify using ice_read_flash_module for this case,
ice_read_nvm_module is introduced. This is a simple wrapper around
ice_read_flash_module which takes the correct pointer address for the
NVM bank, and forces the 2-byte word format onto the caller.
When reading the NVM versions, some fields are read from the Shadow RAM.
The Shadow RAM is the first 64KB of flash memory, and is populated
during device load. Most fields are copied from a section within the
active NVM bank. In order to read this data from both the active and
inactive NVM banks, we need to read not from the first 64KB of flash,
but instead from the correct offset into the NVM bank. Introduce
ice_read_nvm_sr_copy for this purpose. This function wraps around
ice_read_nvm_module and has the same interface as the ice_read_sr_word,
with the exception of allowing the caller to specify whether to read the
active or inactive flash bank.
With this change, it is now trivial to refactor ice_get_nvm_ver_info to
read using the software mediated ice_read_flash_module interface instead
of relying on the firmware mediated interface. This will be used in the
following change to implement support for stored versions in the devlink
info report.
Additionally, the overall ice_read_flash_module interface will be used
and extended to support all three major flash banks, and additionally to
support reading the flash image security revision information.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice flash contains two copies of each of the NVM, Option ROM, and
Netlist modules. Each bank has a pointer word and a size word. In order
to correctly read from the active flash bank, the driver must calculate
the offset manually.
During NVM initialization, read the Shadow RAM control word and
determine which bank is active for each NVM module. Additionally, cache
the size and pointer values for use in calculating the correct offset.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver uses an array of structures which link an info name with
a function that formats the associated version data into a string.
All existing format functions simply format already captured static data
from the driver hw structure. Future changes will introduce format
functions for reporting the versions of flash sections stored but not
yet applied. This type of version data is not stored as a member of the
hw structure. This is because (a) it might not yet exist in the case
there is no pending flash update, and (b) even if it does, it might
change such as if an update is canceled or replaced by a new update
before finalizing.
We could simply have each format function gather its own data upon being
called. However, in some cases the raw binary version data is
a combination of multiple different reported fields. Additionally, the
current interface doesn't have a way for the function to indicate that
the version doesn't exist.
Refactor this function interface to take a new ice_info_ctx structure
instead of the buffer pointer and length. This context structure allows
for future extensions to pre-gather version data that is stored within
the context struct instead of the hw struct.
Allocate this context structure initially at the start of
ice_devlink_info_get. We use dynamic allocation instead of a local stack
variable in order to avoid using too much kernel stack once we extend it
with additional data structures.
Modify the main loop that drives the info reporting so that the version
buffer string is always cleared between each format. Explicitly check
that the format function actually filled in a version string of non-zero
length. If the string is not provided, simply skip this version without
reporting an error. This allows for introducing format functions of
versions which may or may not be present, such as the version of
a pending update that has not yet been activated.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_nvm_info structure has become somewhat of a dumping ground for
all of the fields related to flash version. It holds the NVM version and
EETRACK id, the OptionROM info structure, the flash size, the ShadowRAM
size, and more.
A future change is going to add the ability to read the NVM version and
EETRACK ID from the inactive NVM bank. To make this simpler, it is
useful to have these NVM version info fields extracted to their own
structure.
Rename ice_nvm_info into ice_flash_info, and create a separate
ice_nvm_info structure that will contain the eetrack and NVM map
version. Move the netlist_ver structure into ice_flash_info and rename it
ice_netlist_info for consistency.
Modify the static ice_get_orom_ver_info to take the option rom structure
as a pointer. This makes it more obvious what portion of the hw struct
is being modified. Do the same for ice_get_netlist_ver_info.
Introduce a new ice_get_nvm_ver_info function, which will be similar to
ice_get_orom_ver_info and ice_get_netlist_ver_info, used to keep the NVM
version extraction code co-located.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When erasing, notify userspace of how long we will potentially take to
erase a module. Doing so allows userspace to report the timeout, giving
a clear indication of the upper time bound of the operation.
Since we're re-using the erase timeout value, make it a macro rather
than a magic number.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Shannon Nelson <snelson@pensando.io>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Now we can remove a bunch of identical functions from the drivers and
make them use common dev_page_is_reusable(). All {,un}likely() checks
are omitted since it's already present in this helper.
Also update some comments near the call sites.
Suggested-by: David Rientjes <rientjes@google.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/can/dev.c
b552766c87 ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec9 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c4 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf2287 ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5a ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current MSI-X enablement logic tries to enable best-case MSI-X
vectors and if that fails we only support a bare-minimum set. This
includes a single MSI-X for 1 Tx and 1 Rx queue and a single MSI-X
for the OICR interrupt. Unfortunately, the driver fails to load when we
don't get as many MSI-X as requested for a couple reasons.
First, the code to allocate MSI-X in the driver tries to allocate
num_online_cpus() MSI-X for LAN traffic without caring about the number
of MSI-X actually enabled/requested from the kernel for LAN traffic.
So, when calling ice_get_res() for the PF VSI, it returns failure
because the number of available vectors is less than requested. Fix
this by not allowing the PF VSI to allocation more than
pf->num_lan_msix MSI-X vectors and pf->num_lan_msix Rx/Tx queues.
Limiting the number of queues is done because we don't want more than
1 Tx/Rx queue per interrupt due to performance conerns.
Second, the driver assigns pf->num_lan_msix = 2, to account for LAN
traffic and the OICR. However, pf->num_lan_msix is only meant for LAN
MSI-X. This is causing a failure when the PF VSI tries to
allocate/reserve the minimum pf->num_lan_msix because the OICR MSI-X has
already been reserved, so there may not be enough MSI-X vectors left.
Fix this by setting pf->num_lan_msix = 1 for the failure case. Then the
ICE_MIN_MSIX accounts for the LAN MSI-X and the OICR MSI-X needed for
the failure case.
Update the related defines used in ice_ena_msix_range() to align with
the above behavior and remove the unused RDMA defines because RDMA is
currently not supported. Also, remove the now incorrect comment.
Fixes: 152b978a1f ("ice: Rework ice_ena_msix_range")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently users could create more channels than LAN MSI-X available.
This is happening because there is no check against pf->num_lan_msix
when checking the max allowed channels and will cause performance issues
if multiple Tx and Rx queues are tied to a single MSI-X. Fix this by not
allowing more channels than LAN MSI-X available in pf->num_lan_msix.
Fixes: 87324e747f ("ice: Implement ethtool ops for channels")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the driver to copy the MAC address configured in ndo_set_mac_address
into dev_addr, even if the MAC filter already exists in HW. In some
situations (e.g. bonding) the netdev's dev_addr could have been modified
outside of the driver, with no change to the HW filter, so the driver
cannot assume that they match.
Fixes: 757976ab16 ("ice: Fix check for removing/adding mac filters")
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This patch is based on a similar change to i40e by Slawomir Laba:
"i40e: Implement flow for IPv6 next header (extension header)".
When a packet contains an IPv6 header with next header which is
an extension header and not a protocol one, the kernel function
skb_transport_header called with such sk_buff will return a
pointer to the extension header and not to the TCP one.
The above explained call caused a problem with packet processing
for skb with encapsulation for tunnel with ICE_TX_CTX_EIPT_IPV6.
The extension header was not skipped at all.
The ipv6_skip_exthdr function does check if next header of the IPV6
header is an extension header and doesn't modify the l4_proto pointer
if it points to a protocol header value so its safe to omit the
comparison of exthdr and l4.hdr pointers. The ipv6_skip_exthdr can
return value -1. This means that the skipping process failed
and there is something wrong with the packet so it will be dropped.
Fixes: a4e82a81f5 ("ice: Add support for tunnel offloads")
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The packet classifier would occasionally misrecognize an IPv6 training
packet when the next protocol field was 0. The correct value for
unspecified protocol is IPPROTO_NONE.
Fixes: 165d80d6ad ("ice: Support IPv6 Flow Director filters")
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-01-16
1) Extend atomic operations to the BPF instruction set along with x86-64 JIT support,
that is, atomic{,64}_{xchg,cmpxchg,fetch_{add,and,or,xor}}, from Brendan Jackman.
2) Add support for using kernel module global variables (__ksym externs in BPF
programs) retrieved via module's BTF, from Andrii Nakryiko.
3) Generalize BPF stackmap's buildid retrieval and add support to have buildid
stored in mmap2 event for perf, from Jiri Olsa.
4) Various fixes for cross-building BPF sefltests out-of-tree which then will
unblock wider automated testing on ARM hardware, from Jean-Philippe Brucker.
5) Allow to retrieve SOL_SOCKET opts from sock_addr progs, from Daniel Borkmann.
6) Clean up driver's XDP buffer init and split into two helpers to init per-
descriptor and non-changing fields during processing, from Lorenzo Bianconi.
7) Minor misc improvements to libbpf & bpftool, from Ian Rogers.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (41 commits)
perf: Add build id data in mmap2 event
bpf: Add size arg to build_id_parse function
bpf: Move stack_map_get_build_id into lib
bpf: Document new atomic instructions
bpf: Add tests for new BPF atomic operations
bpf: Add bitwise atomic instructions
bpf: Pull out a macro for interpreting atomic ALU operations
bpf: Add instructions for atomic_[cmp]xchg
bpf: Add BPF_FETCH field / create atomic_fetch_add instruction
bpf: Move BPF_STX reserved field check into BPF_STX verifier code
bpf: Rename BPF_XADD and prepare to encode other atomics in .imm
bpf: x86: Factor out a lookup table for some ALU opcodes
bpf: x86: Factor out emission of REX byte
bpf: x86: Factor out emission of ModR/M for *(reg + off)
tools/bpftool: Add -Wall when building BPF programs
bpf, libbpf: Avoid unused function warning on bpf_tail_call_static
selftests/bpf: Install btf_dump test cases
selftests/bpf: Fix installation of urandom_read
selftests/bpf: Move generated test files to $(TEST_GEN_FILES)
selftests/bpf: Fix out-of-tree build
...
====================
Link: https://lore.kernel.org/r/20210116012922.17823-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
napi_gro_receive() can never return GRO_DROP
GRO_DROP can only be returned from napi_gro_frags()
which is the other NAPI GRO entry point.
Followup patch will remove GRO_DROP, because drivers
are not supposed to call napi_gro_frags() if prior
napi_get_frags() has failed.
Note that I have left the gro_dropped variable. I leave to ice
maintainers the decision to further remove it from ethtool -S results.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All UDP tunnel port management is now routed via udp_tunnel_nic
infra directly. Remove the old callbacks.
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On the Rx side, the next_to_use index points to the next item in the
HW ring to be refilled/allocated, and next_to_clean points to the next
item to potentially be processed.
When the HW Rx ring is fully refilled, i.e. no packets has been
processed, the next_to_use will be next_to_clean - 1. When the ring is
fully processed next_to_clean will be equal to next_to_use. The latter
case is where a bug is triggered.
If the next_to_use bits are not cleared, and the "fully processed"
state is entered, a stale descriptor can be processed.
The skb-path correctly clear the status bit for the next_to_use
descriptor, but the AF_XDP zero-copy path did not do that.
This change adds the status bits clearing of the next_to_use
descriptor.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead doing the check for allocation in each loop, move it outside
the while loop and do it every NAPI loop.
This change boosts the xdpsock rxdrop scenario with 15% more
packets-per-second.
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/r/20201211085410.59350-1-bjorn.topel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The page recycle code, incorrectly, relied on that a page fragment
could not be freed inside xdp_do_redirect(). This assumption leads to
that page fragments that are used by the stack/XDP redirect can be
reused and overwritten.
To avoid this, store the page count prior invoking xdp_do_redirect().
Fixes: efc2214b60 ("ice: Add support for XDP")
Reported-and-analyzed-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add space to the end of 'Unknown' string in order to avoid
concatenation with 'bps' string when formatting netdev log message.
Signed-off-by: Simon Perron Caissy <simon.perron.caissy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When printing messages with ice_debug, align the printed string to the
origin line of the message in order to ease debugging and tracking
messages back to their source.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
sparse warns about cast to/from restricted types which is not
an actual problem; silence the warning.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The maximum Admin Queue buffer size and NVM shadow RAM sector size are both
4 Kilobytes. Some comments refer to those as 4Kb which can be confused with
4 Kilobits. Update the comments to use the commonly used KB symbol instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
vlan_ena was introduced to track whether VLAN filters are enabled on
the device, but
1) checking for num_vlan > 1 already gives us this information, and is
currently used in this way throughout the code
2) the logic for vlan_ena is broken when multiple VLANs are active
Just remove vlan_ena and use num_vlan instead.
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the gate that prevents the OROM and netlist info from being
populated. The NVM now has the appropriate section for software to
reference the versioning info.
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver is able to override the firmware when it comes to supporting
a more lenient link mode. This feature was limited to E810 devices. It
is now extended to E82X devices.
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There are times when the driver shouldn't return an error when the Get
PHY abilities AQ command (0x0600) returns an error. Instead the driver
should log that the error occurred and continue on. This allows the
driver to load even though the AQ command failed. The user can then
later determine the reason for the failure and correct it.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In ice_flow_add_prof_sync(), struct ice_flow_prof_params has recently
grown in size hogging stack space when allocated there. Hogging stack
space should be avoided. Change allocation to be on the heap when needed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Harikumar Bokkena <harikumarx.bokkena@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-12-03
The main changes are:
1) Support BTF in kernel modules, from Andrii.
2) Introduce preferred busy-polling, from Björn.
3) bpf_ima_inode_hash() and bpf_bprm_opts_set() helpers, from KP Singh.
4) Memcg-based memory accounting for bpf objects, from Roman.
5) Allow bpf_{s,g}etsockopt from cgroup bind{4,6} hooks, from Stanislav.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (118 commits)
selftests/bpf: Fix invalid use of strncat in test_sockmap
libbpf: Use memcpy instead of strncpy to please GCC
selftests/bpf: Add fentry/fexit/fmod_ret selftest for kernel module
selftests/bpf: Add tp_btf CO-RE reloc test for modules
libbpf: Support attachment of BPF tracing programs to kernel modules
libbpf: Factor out low-level BPF program loading helper
bpf: Allow to specify kernel module BTFs when attaching BPF programs
bpf: Remove hard-coded btf_vmlinux assumption from BPF verifier
selftests/bpf: Add CO-RE relocs selftest relying on kernel module BTF
selftests/bpf: Add support for marking sub-tests as skipped
selftests/bpf: Add bpf_testmod kernel module for testing
libbpf: Add kernel module BTF support for CO-RE relocations
libbpf: Refactor CO-RE relocs to not assume a single BTF object
libbpf: Add internal helper to load BTF data by FD
bpf: Keep module's btf_data_size intact after load
bpf: Fix bpf_put_raw_tracepoint()'s use of __module_address()
selftests/bpf: Add Userspace tests for TCP_WINDOW_CLAMP
bpf: Adds support for setting window clamp
samples/bpf: Fix spelling mistake "recieving" -> "receiving"
bpf: Fix cold build of test_progs-no_alu32
...
====================
Link: https://lore.kernel.org/r/20201204021936.85653-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add napi_id to the xdp_rxq_info structure, and make sure the XDP
socket pick up the napi_id in the Rx path. The napi_id is used to find
the corresponding NAPI structure for socket busy polling.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/bpf/20201130185205.196029-7-bjorn.topel@gmail.com
When performing a flash update via devlink, device drivers may inform
user space of status updates via
devlink_flash_update_(begin|end|timeout|status)_notify functions.
It is expected that drivers do not send any status notifications unless
they send a begin and end message. If a driver sends a status
notification without sending the appropriate end notification upon
finishing (regardless of success or failure), the current implementation
of the devlink userspace program can get stuck endlessly waiting for the
end notification that will never come.
The current ice driver implementation may send such a status message
without the appropriate end notification in rare cases.
Fixing the ice driver is relatively simple: we just need to send the
begin_notify at the start of the function and always send an end_notify
no matter how the function exits.
Rather than assuming driver authors will always get this right in the
future, lets just fix the API so that it is not possible to get wrong.
Make devlink_flash_update_begin_notify and
devlink_flash_update_end_notify static, and call them in devlink.c core
code. Always send the begin_notify just before calling the driver's
flash_update routine. Always send the end_notify just after the routine
returns regardless of success or failure.
Doing this makes the status notification easier to use from the driver,
as it no longer needs to worry about catching failures and cleaning up
by calling devlink_flash_update_end_notify. It is now no longer possible
to do the wrong thing in this regard. We also save a couple of lines of
code in each driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All drivers which implement the devlink flash update support, with the
exception of netdevsim, use either request_firmware or
request_firmware_direct to locate the firmware file. Rather than having
each driver do this separately as part of its .flash_update
implementation, perform the request_firmware within net/core/devlink.c
Replace the file_name parameter in the struct devlink_flash_update_params
with a pointer to the fw object.
Use request_firmware rather than request_firmware_direct. Although most
Linux distributions today do not have the fallback mechanism
implemented, only about half the drivers used the _direct request, as
compared to the generic request_firmware. In the event that
a distribution does support the fallback mechanism, the devlink flash
update ought to be able to use it to provide the firmware contents. For
distributions which do not support the fallback userspace mechanism,
there should be essentially no difference between request_firmware and
request_firmware_direct.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A subsequent addition of an IP4 or IP6 rule after other rules would
overwrite any existing TCAM entries of related L4 protocols(ex: tcp4 or
udp6). This was due to the mask including too many TCAM entries. Add new
packet type masks with bits properly excluded so rules are not overwritten.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pointers should be casted to unsigned long to avoid
-Wpointer-to-int-cast warnings:
drivers/net/ethernet/intel/ice/ice_flow.h:197:33: warning:
cast from pointer to integer of different size
drivers/net/ethernet/intel/ice/ice_flow.h:198:32: warning:
cast to pointer from integer of different size
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While debugging a recent failure to update the flash of an ice device,
I found it helpful to add additional logging which helped determine the
root cause of the problem being a timeout issue.
Add some extra dev_dbg() logging messages which can be enabled using the
dynamic debug facility, including one for ice_aq_wait_for_event that
will use jiffies to capture a rough estimate of how long we waited for
the completion of a firmware command.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the devlink_port structure is stored within the ice_pf. This
made sense because we create a single devlink_port for each PF. This
setup does not mesh with the abstractions in the driver very well, and
led to a flow where we accidentally call devlink_port_unregister twice
during error cleanup.
In particular, if devlink_port_register or devlink_port_unregister are
called twice, this leads to a kernel panic. This appears to occur during
some possible flows while cleaning up from a failure during driver
probe.
If register_netdev fails, then we will call devlink_port_unregister in
ice_cfg_netdev as it cleans up. Later, we again call
devlink_port_unregister since we assume that we must cleanup the port
that is associated with the PF structure.
This occurs because we cleanup the devlink_port for the main PF even
though it was not allocated. We allocated the port within a per-VSI
function for managing the main netdev, but did not release the port when
cleaning up that VSI, the allocation and destruction are not aligned.
Instead of attempting to manage the devlink_port as part of the PF
structure, manage it as part of the PF VSI. Doing this has advantages,
as we can match the de-allocation of the devlink_port with the
unregister_netdev associated with the main PF VSI.
Moving the port to the VSI is preferable as it paves the way for
handling devlink ports allocated for other purposes such as SR-IOV VFs.
Since we're changing up how we allocate the devlink_port, also change
the indexing. Originally, we indexed the port using the PF id number.
This came from an old goal of sharing a devlink for each physical
function. Managing devlink instances across multiple function drivers is
not workable. Instead, lets set the port number to the logical port
number returned by firmware and set the index using the VSI index
(sometimes referred to as VSI handle).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add "fw.app.bundle_id" to display the DDP Track ID of the active DDP
package. This id is similar to "fw.bundle_id" and is a unique identifier
for the DDP package that is loaded in the device. Each new DDP has
a unique Track ID generated for it, and the ID can be used to identify
and track the DDP package.
Add documentation for the new devlink info version.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ice_info_get_dsn always returns 0, so just make it void.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A new test in checkpatch detects repeated words; cleanup all pre-existing
occurrences of those now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Co-developed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use %*phD format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver initializes in safe mode, it will call
ice_set_safe_mode_caps. This results in clearing the capabilities
structures, in order to set them up for operating in safe mode, ensuring
many features are disabled.
This has a side effect of also clearing the capability bits that relate
to NVM update. The result is that the device driver will not indicate
support for unified update, even if the firmware is capable.
Fix this by adding the relevant capability fields to the list of values
we preserve. To simplify the code, use a common_cap structure instead of
a handful of local variables. To reduce some duplication of the
capability name, introduce a couple of macros used to restore the
capabilities values from the cached copy.
Fixes: de9b277ee0 ("ice: Add support for unified NVM update flow capability")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver needs to wait for a firmware response to each command to
write a block of data to the scratch area used to update the device
firmware. The driver currently waits for up to 1 second for this to be
returned.
It turns out that firmware might take longer than 1 second to return
a completion in some cases. If this happens, the flash update will fail
to complete.
Fix this by increasing the maximum time that the driver will wait for
both writing a block of data, and for activating the new NVM bank. The
timeout for an erase command is already several minutes, as the firmware
had to erase the entire bank which was already expected to take a minute
or more in the worst case.
In the case where firmware really won't respond, we will now take longer
to fail. However, this ensures that if the firmware is simply slow to
respond, the flash update can still complete. This new maximum timeout
should not adversely increase the update time, as the implementation for
wait_event_interruptible_timeout, and should wake very soon after we get
a completion event. It is better for a flash update be slow but still
succeed than to fail because we gave up too quickly.
Fixes: d69ea414c9 ("ice: implement device flash update via devlink")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
in_interrupt() is ill defined and does not provide what the name
suggests. The usage especially in driver code is deprecated and a tree wide
effort to clean up and consolidate the (ab)usage of in_interrupt() and
related checks is happening.
In this case the checks cover only parts of the contexts in which these
functions cannot be called. They fail to detect preemption or interrupt
disabled invocations.
As the functions which are invoked from the various places contain already
a broad variety of checks (always enabled or debug option dependent) cover
all invalid conditions already, there is no point in having inconsistent
warnings in those drivers.
Just remove them.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert ice to the new infra, use share port tables.
Leave a tiny bit more error checking in place than usual,
because this driver really does quite a bit of magic.
We need to calculate the number of VxLAN and GENEVE entries
the firmware has reserved.
Thanks to the conversion the driver will no longer sleep in
an atomic section.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ice_get_open_tunnel_port() is always passed TNL_ALL
as the second parameter.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the recently added DEVLINK_ATTR_FLASH_UPDATE_OVERWRITE_MASK
parameter in the ice flash update handler. Convert the overwrite mask
bitfield into the appropriate preservation level used by the firmware
when updating.
Because there is no equivalent preservation level for overwriting only
identifiers, this combination is rejected by the driver as not supported
with an appropriate extended ACK message.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink core recently gained support for checking whether the driver
supports a flash_update parameter, via `supported_flash_update_params`.
However, parameters are specified as function arguments. Adding a new
parameter still requires modifying the signature of the .flash_update
callback in all drivers.
Convert the .flash_update function to take a new `struct
devlink_flash_update_params` instead. By using this structure, and the
`supported_flash_update_params` bit field, a new parameter to
flash_update can be added without requiring modification to existing
drivers.
As before, all parameters except file_name will require driver opt-in.
Because file_name is a necessary field to for the flash_update to make
sense, no "SUPPORTED" bitflag is provided and it is always considered
valid. All future additional parameters will require a new bit in the
supported_flash_update_params bitfield.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When implementing .flash_update, drivers which do not support
per-component update are manually checking the component parameter to
verify that it is NULL. Without this check, the driver might accept an
update request with a component specified even though it will not honor
such a request.
Instead of having each driver check this, move the logic into
net/core/devlink.c, and use a new `supported_flash_update_params` field
in the devlink_ops. Drivers which will support per-component update must
now specify this by setting DEVLINK_SUPPORT_FLASH_UPDATE_COMPONENT in
the supported_flash_update_params in their devlink_ops.
This helps ensure that drivers do not forget to check for a NULL
component if they do not support per-component update. This also enables
a slightly better error message by enabling the core stack to set the
netlink bad attribute message to indicate precisely the unsupported
attribute in the message.
Going forward, any new additional parameter to flash update will require
a bit in the supported_flash_update_params bitfield.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Cc: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
This takes care of all of the trivial W=1 fixes in the Intel
Ethernet drivers, which allows developers and maintainers to
build more of the networking tree with more complete warning
checks.
There are three classes of kdoc warnings fixed:
- cannot understand function prototype: 'x'
- Excess function parameter 'x' description in 'y'
- Function parameter or member 'x' not described in 'y'
All of the changes were trivial comment updates on
function headers.
Inspired by Lee Jones' series of wireless work to do the same.
Compile tested only, and passes simple test of
$ git ls-files *.[ch] | egrep drivers/net/ethernet/intel | \
xargs scripts/kernel-doc -none
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During ice_vsi_setup, if ice_cfg_vsi_lan fails, it does not properly
release memory associated with the VSI rings. If we had used devres
allocations for the rings, this would be ok. However, we use kzalloc and
kfree_rcu for these ring structures.
Using the correct label to cleanup the rings during ice_vsi_setup
highlights an issue in the ice_vsi_clear_rings function: it can leave
behind stale ring pointers in the q_vectors structure.
When releasing rings, we must also ensure that no q_vector associated
with the VSI will point to this ring again. To resolve this, loop over
all q_vectors and release their ring mapping. Because we are about to
free all rings, no q_vector should remain pointing to any of the rings
in this VSI.
Fixes: 5513b920a4 ("ice: Update Tx scheduler tree for VSI multi-Tx queue support")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
