Remove redundant spinlock acquire parameter from ena_com_admin_init()
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improves socket memory utilization when receiving packets larger
than 128 bytes (the previous rx copybreak) and smaller than 256 bytes.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently Rx refill is done when the number of required descriptors is
above 1/8 queue size. With a default of 1024 entries per queue the
threshold is 128 descriptors.
There is intention to increase the queue size to 8196 entries.
In this case threshold of 1024 descriptors is too large and can hurt
latency.
Add another limitation to Rx threshold to be at most 256 descriptors.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set skb->ip_summed to the correct value as reported by the device.
Add counter for the case where rx csum offload is enabled but
device didn't check it.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes all code changes necessary in ena_netdev to enable
packet sending via the LLQ placemnt mode.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces APIs for detection, initialization, configuration
and actual usage of low latency queues(LLQ). It extends transmit API with
creation of LLQ descriptors in device memory (which include host buffers
descriptors as well as packet header)
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Low Latency Queues(LLQ) allow usage of device's memory for descriptors
and headers. Such queues decrease processing time since data is already
located on the device when driver rings the doorbell.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new fields and definitions to host info and fill them
according to the latest ENA spec version.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce fastpath overhead by making ena_com_tx_comp_req_id_get() inline.
Also move it to ena_eth_com.h file with its dependency function
ena_com_cq_inc_head().
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate potential auto casting compilation error.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi poll functions should be initialized before running request_irq(),
to handle a rare condition where there is a pending interrupt, causing
the ISR to fire immediately while the poll function wasn't set yet,
causing a NULL dereference.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a rare scenario when ena_device_restore() fails, followed by device
remove, an FLR will not be issued. In this case, the device will keep
sending asynchronous AENQ keep-alive events, even after driver removal,
leading to memory corruption.
Fixes: 8c5c7abdeb ("net: ena: add power management ops to the ENA driver")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory mapped with devm_ioremap is automatically freed when the driver
is disconnected from the device. Therefore there is no need to
explicitly call devm_iounmap.
Fixes: 0857d92f71 ("net: ena: add missing unmap bars on device removal")
Fixes: 411838e7b4 ("net: ena: fix rare kernel crash when bar memory remap fails")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ena uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Netanel Belgazal <netanel@amazon.com>
Cc: Saeed Bishara <saeedb@amazon.com>
Cc: Zorik Machulsky <zorik@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
module.h already contained moduleparam.h, so it is safe to remove
the redundant include.
The issue is detected with the help of Coccinelle.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added memory barriers where they were missing to support multiple
architectures, and removed redundant ones.
As part of removing the redundant memory barriers and improving
performance, we moved to more relaxed versions of memory barriers,
as well as to the more relaxed version of writel - writel_relaxed,
while maintaining correctness.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add READ_ONCE calls where necessary (for example when iterating
over a memory field that gets updated by the hardware).
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
acquire the rtnl_lock during device destruction to avoid
using partially destroyed device.
ena_remove() shares almost the same logic as ena_destroy_device(),
so use ena_destroy_device() and avoid duplications.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ena_destroy_device() can potentially be called twice.
To avoid this, check that the device is running and
only then proceed destroying it.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ena_destroy_device() is called from ena_suspend(), the device is
still reachable from the driver. Therefore, the driver can send a command
to the device to free all resources.
However, in all other cases of calling ena_destroy_device(), the device is
potentially in an error state and unreachable from the driver. In these
cases the driver must not send commands to the device.
The current implementation does not request resource freeing from the
device even when possible. We add the graceful parameter to
ena_destroy_device() to enable resource freeing when possible, and
use it in ena_suspend().
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffer length field in the ena rx descriptor is 16 bit, and the
current driver passes a full page in each ena rx descriptor.
When PAGE_SIZE equals 64kB or more, the buffer length field becomes
zero.
To solve this issue, limit the ena Rx descriptor to use 16kB even
when allocating 64kB kernel pages. This change would not impact ena
device functionality, as 16kB is still larger than maximum MTU.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with driver version 1.5.0, in case of a surprise device
unplug, there is a race caused by invoking ena_destroy_device()
from two different places. As a result, the readless register might
be accessed after it was destroyed.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
UBSAN triggers the following undefined behaviour warnings:
[...]
[ 13.236124] UBSAN: Undefined behaviour in drivers/net/ethernet/amazon/ena/ena_eth_com.c:468:22
[ 13.240043] shift exponent 64 is too large for 64-bit type 'long long unsigned int'
[...]
[ 13.744769] UBSAN: Undefined behaviour in drivers/net/ethernet/amazon/ena/ena_eth_com.c:373:4
[ 13.748694] shift exponent 64 is too large for 64-bit type 'long long unsigned int'
[...]
When splitting the address to high and low, GENMASK_ULL is used to generate
a bitmask with dma_addr_bits field from io_sq (in ena_com_prepare_tx and
ena_com_add_single_rx_desc).
The problem is that dma_addr_bits is not initialized with a proper value
(besides being cleared in ena_com_create_io_queue).
Assign dma_addr_bits the correct value that is stored in ena_dev when
initializing the SQ.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Gal Pressman <pressmangal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For most of these calls we can just pass NULL through to the fallback
function as the sb_dev. The only cases where we cannot are the cases where
we might be dealing with either an upper device or a driver that would
have configured things to support an sb_dev itself.
The only driver that has any significant change in this patch set should be
ixgbe as we can drop the redundant functionality that existed in both the
ndo_select_queue function and the fallback function that was passed through
to us.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes it so that instead of passing a void pointer as the
accel_priv we instead pass a net_device pointer as sb_dev. Making this
change allows us to pass the subordinate device through to the fallback
function eventually so that we can keep the actual code in the
ndo_select_queue call as focused on possible on the exception cases.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of implementing our own version of a SR-IOV configuration stub in
the ena driver, use the existing pci_sriov_configure_simple() function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Code includes barrier() followed by writel(). writel() already has a
barrier on some architectures like arm64.
This ends up CPU observing two barriers back to back before executing the
register write.
Create a new wrapper function with relaxed write operator. Use the new
wrapper when a write is following a barrier().
Since code already has an explicit barrier call, changing writel() to
writel_relaxed() and adding mmiowb() for ordering protection.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENA admin command queue errors are not handled as part of ena_down().
As a result, in case of error admin queue transitions to non-running
state and aborts all subsequent commands including those coming from
ena_up(). Reset scheduled by the driver from the timer service
context would not proceed due to sharing rtnl with ena_up()/ena_down()
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under certain conditions MSI-X interrupt might arrive right after it
was unmasked in ena_up(). There is a chance it would be processed by
the driver before device ENA_FLAG_DEV_UP flag is set. In such a case
the interrupt is ignored.
ENA device operates in auto-masked mode, therefore ignoring
interrupt leaves it masked for good.
Moving unmask of interrupt to be the last step in ena_up().
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A mechanism for detection of stuck Rx/Tx rings due to missed or
misrouted interrupts.
Check if there are unhandled completion descriptors before the first
MSI-X interrupt arrived.
The check is per queue and per interrupt vector.
Once such condition is detected, driver and device reset is scheduled.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases, ena driver would reset and re-start the device,
for example, in case of misbehaving application that causes
transmit timeout
The first step in the reset procedure is to stop the Tx traffic by
calling ena_carrier_off().
After the driver have just started the device reset procedure, device
happens to send an asynchronous notification (via AENQ) to the driver
than there was a link change (to link-up state).
This link change is mapped to a call to netif_carrier_on() which
re-activates the Tx queues, violating the assumption of no tx traffic
until device reset is completed, as the reset task might still be in
the process of queues initialization, leading to an access to
uninitialized memory.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge updates from Andrew Morton:
- a few misc bits
- ocfs2 updates
- almost all of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (131 commits)
memory hotplug: fix comments when adding section
mm: make alloc_node_mem_map a void call if we don't have CONFIG_FLAT_NODE_MEM_MAP
mm: simplify nodemask printing
mm,oom_reaper: remove pointless kthread_run() error check
mm/page_ext.c: check if page_ext is not prepared
writeback: remove unused function parameter
mm: do not rely on preempt_count in print_vma_addr
mm, sparse: do not swamp log with huge vmemmap allocation failures
mm/hmm: remove redundant variable align_end
mm/list_lru.c: mark expected switch fall-through
mm/shmem.c: mark expected switch fall-through
mm/page_alloc.c: broken deferred calculation
mm: don't warn about allocations which stall for too long
fs: fuse: account fuse_inode slab memory as reclaimable
mm, page_alloc: fix potential false positive in __zone_watermark_ok
mm: mlock: remove lru_add_drain_all()
mm, sysctl: make NUMA stats configurable
shmem: convert shmem_init_inodecache() to void
Unify migrate_pages and move_pages access checks
mm, pagevec: rename pagevec drained field
...
As the page free path makes no distinction between cache hot and cold
pages, there is no real useful ordering of pages in the free list that
allocation requests can take advantage of. Juding from the users of
__GFP_COLD, it is likely that a number of them are the result of copying
other sites instead of actually measuring the impact. Remove the
__GFP_COLD parameter which simplifies a number of paths in the page
allocator.
This is potentially controversial but bear in mind that the size of the
per-cpu pagelists versus modern cache sizes means that the whole per-cpu
list can often fit in the L3 cache. Hence, there is only a potential
benefit for microbenchmarks that alloc/free pages in a tight loop. It's
even worse when THP is taken into account which has little or no chance
of getting a cache-hot page as the per-cpu list is bypassed and the
zeroing of multiple pages will thrash the cache anyway.
The truncate microbenchmarks are not shown as this patch affects the
allocation path and not the free path. A page fault microbenchmark was
tested but it showed no sigificant difference which is not surprising
given that the __GFP_COLD branches are a miniscule percentage of the
fault path.
Link: http://lkml.kernel.org/r/20171018075952.10627-9-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new statistic to ethtool stats that show the number of packets
without transmit acknowledgement from ENA device.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove ena_device_io_suspend/resume() methods
Those methods were intend to be used by the device to trigger
suspend/resume but eventually it was dropped.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ena admin commands timeout is in resolutions of 100ms.
Therefore, When the driver works in polling mode, it sleeps for 100ms
each time. The overall boot time of the ENA driver is ~1.5 sec.
To reduce the boot time, This change modifies the granularity of
the sleeps to 5ms.
This change improves the boot time to 220ms.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool ena_get_channels() expose the max number of queues as the max
number of queues ENA supports (128 queues) and not the actual number
of created queues.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Decrease log level of checksum errors as these messages can be
triggered remotely by bad packets.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx drop counter is reported by the device in the keep-alive
event.
update the driver's counter with the device counter.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ena_com_mem_addr_set(), use the above functions to split dma address
to the lower 32 bits and the higher 16 bits.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver tries to allocate msix vectors as the number of the
negotiated io queues. (with another msix vector for management).
If pci_alloc_irq_vectors() fails, the driver aborts the probe
and the ENA network device is never brought up.
With this patch, the driver's logic will reduce the number of IO
queues to the number of allocated msix vectors (minus one for management)
instead of failing probe().
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENA driver post Rx buffers through the Rx submission queue
for the ENA device to fill them with receive packets.
Each Rx buffer is marked with req_id in the Rx descriptor.
Newer ENA devices could consume the posted Rx buffer in out of order,
and as result the corresponding Rx completion queue will have Rx
completion descriptors with non contiguous req_id(s)
In this change the driver holds two rings.
The first ring (called free_rx_ids) is a mapping ring.
It holds all the unused request ids.
The values in this ring are from 0 to ring_size -1.
When the driver wants to allocate a new Rx buffer it uses the head of
free_rx_ids and uses it's value as the index for rx_buffer_info ring.
The req_id is also written to the Rx descriptor
Upon Rx completion,
The driver took the req_id from the completion descriptor and uses it
as index in rx_buffer_info.
The req_id is then return to the free_rx_ids ring.
This patch also adds statistics to inform when the driver receive out
of range or unused req_id.
Note:
free_rx_ids is only accessible from the napi handler, so no locking is
required
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each device reset, log to the device what is the cause
the reset occur.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using:
memset(ptr, 0x0, sizeof(struct ...))
use:
memset(ptr, 0x0, sizeor(*ptr))
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, ENA device can update the ena driver about
the desired timeout values:
These values are part of the "hardware hints" which are transmitted
to the driver as Asynchronous event through ENA async
event notification queue.
In case the ENA device does not support this capability,
the driver will use its own default values.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
check_for_missing_tx_completions() is called from a timer
task and looking for lost tx packets.
The old implementation accumulate all the lost tx packets
and did not check if those packets were retrieved on a later stage.
This cause to a situation where the driver reset
the device for no reason.
Fixes: 1738cd3ed3 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 1738cd3ed3 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the rare case where the device runs out of free rx buffer
descriptors (in case of pressure on kernel memory),
and the napi handler continuously fail to refill new Rx descriptors
until device rx queue totally runs out of all free rx buffers
to post incoming packet, leading to a deadlock:
* The device won't send interrupts since all the new
Rx packets will be dropped.
* The napi handler won't try to allocate new Rx descriptors
since allocation is part of NAPI that's not being invoked any more
The fix involves detecting this scenario and rescheduling NAPI
(to refill buffers) by the keepalive/watchdog task.
Fixes: 1738cd3ed3 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch also change the mapping functions to devm_ functions
Fixes: 1738cd3ed3 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug:
"Completion context is occupied" error printout will be noticed in
dmesg.
This error will cause the admin command to fail, which will lead to
an ena_probe() failure or a watchdog reset (depends on which admin
command failed).
Root cause:
__ena_com_submit_admin_cmd() is the function that submits new entries to
the admin queue.
The function have a check that makes sure the queue is not full and the
function does not override any outstanding command.
It uses head and tail indexes for this check.
The head is increased by ena_com_handle_admin_completion() which runs
from interrupt context, and the tail index is increased by the submit
function (the function is running under ->q_lock, so there is no risk
of multithread increment).
Each command is associated with a completion context. This context
allocated before call to __ena_com_submit_admin_cmd() and freed by
ena_com_wait_and_process_admin_cq_interrupts(), right after the command
was completed.
This can lead to a state where the head was increased, the check passed,
but the completion context is still in use.
Solution:
Use the atomic variable ->outstanding_cmds instead of using the head and
the tail indexes.
This variable is safe for use since it is bumped in get_comp_ctx() in
__ena_com_submit_admin_cmd() and is freed by comp_ctxt_release()
Fixes: 1738cd3ed3 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 1738cd3ed3 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixing a bug that the driver does not unmask the IO interrupts
in ndo_open():
occasionally, the MSI-X interrupt (for one or more IO queues)
can be masked when ndo_close() was called.
If that is followed by ndo open(),
then the MSI-X will be still masked so no interrupt
will be received by the driver.
Fixes: 1738cd3ed3 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current flow to detect admin completion is:
while (command_not_completed) {
if (timeout)
error
check_for_completion()
sleep()
}
So in case the sleep took more than the timeout
(in case the thread/workqueue was not scheduled due to higher priority
task or prolonged VMexit), the driver can detect a stall even if
the completion is present.
The fix changes the order of this function to first check for
completion and only after that check if the timeout expired.
Fixes: 1738cd3ed3 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the deprecated pci_enable_msix API in favour of its successor.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check in ena_remove() for the pci driver data not being NULL is not
needed, since it is always set in the probe() function. Remove the
superfluous check.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the host info config to be the first admin command that is executed.
This change require the driver to remove the 'feature check'
from host info configuration flow.
The check is removed since the supported features bitmask field
is retrieved only after calling ENA_ADMIN_DEVICE_ATTRIBUTES admin command.
If set host info is not supported an error will be returned by the device.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timeouts were too agressive and sometimes cause false alarms.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completion descriptors are accessed from the driver and from the device.
To avoid reading the old value, use READ_ONCE macro.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not unamsk interrupts if we are in busy poll mode.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ena driver detects that the device is not behave as expected,
it tries to reset the device.
The reset flow calls ena_down, which will frees all the resources
the driver allocates and then it will reset the device.
This flow can cause memory corruption if the device is still writes
to the driver's memory space.
To overcome this potential race, move the reset before the device
resources are freed.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_get_stat64() can be called from atomic context, but the current
implementation sends an admin command to retrieve the statistics from
the device. This admin command can sleep.
This patch re-factors the implementation of ena_get_stats64() to use
the {rx,tx}bytes/count from the driver's inner counters, and to obtain
the rx drop counter from the asynchronous keep alive (heart bit)
event.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENA default hash configures IPv4_frag hash twice instead of
configure non-IP packets.
The bug caused IPv4 fragmented packets to be calculated based on
L2 source and destination address instead of L3 source and destination.
IPv4 packets can reach to the wrong Rx queue.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ena_flow_data_to_flow_hash and ena_flow_hash_to_flow_type
treat the ena_flow_hash_to_flow_type enum as power of two values.
Change the values of ena_admin_flow_hash_fields to be power of two values.
This bug effect the ethtool set/get rxnfc.
ethtool will report wrong values hash fields for get and will
configure wrong hash fields in set.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ENA driver tries to open a queue per vCPU.
To determine how many vCPUs the instance have it uses num_possible_cpus()
while it should have use num_online_cpus() instead.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove NETIF_F_NTUPLE from netdev->features.
The ENA device driver does not support ntuple filtering.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer() instead of init_timer(), being the preferred/standard
way to set a timer up.
Also, quoting the mod_timer() function comment:
-> mod_timer() is a more efficient way to update the expire field of an
active timer (if the timer is inactive it will be activated).
Use setup_timer and mod_timer to setup and arm a timer, to make the code
cleaner and easier to read.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.
acenic:
- min_mtu = 0, max_mtu = 9000
amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu
amd/xgbe:
- min_mtu = 0, max_mtu = 9000
sb1250:
- min_mtu = 0, max_mtu = 1518
cxgb3:
- min_mtu = 81, max_mtu = 65535
cxgb4:
- min_mtu = 81, max_mtu = 9600
cxgb4vf:
- min_mtu = 81, max_mtu = 65535
benet:
- min_mtu = 256, max_mtu = 9000
ibmveth:
- min_mtu = 68, max_mtu = 65535
ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu
jme:
- min_mtu = 1280, max_mtu = 9202
mv643xx_eth:
- min_mtu = 64, max_mtu = 9500
mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
checks in the respective switch drivers' ndo_change_mtu functions
ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500
netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)
qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
the value is 1500 or 9000
qualcomm/emac:
- min_mtu = 46, max_mtu = 9194
xilinx_axienet:
- min_mtu = 64, max_mtu = 9000
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the return type of ena_set_push_mode() to be void,
as it always returns 0.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the invalid dma width
error handling case instead of 0.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a driver for the ENA family of networking devices.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
